If you do not specify a value for the pps argument in the arp rate-limit command, the default rate limit value applies. Packets that exceed the rate limit are discarded.

Examples

# Enable the ARP packet rate limit feature on GigabitEthernet 1/0/1, and set the maximum ARP packet rate to 50 pps.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] arp rate-limit 50

arp rate-limit log enable

Use arp rate-limit log enable to enable logging for ARP packet rate limit.

Use undo arp rate-limit log enable to disable logging for ARP packet rate limit.

Syntax

arp rate-limit log enable

undo arp rate-limit log enable

Default

Logging for ARP packet rate limit is disabled.

Views

System view

Predefined user roles

network-admin

Usage guidelines

When logging for ARP packet rate limit is enabled, the device sends the highest threshold-crossed ARP packet rate within the sending interval in a log message to the information center. You can configure the information center module to set the log output rules. For more information about information center, see System Management Configuration Guide.

Examples

# Enable logging for ARP packet rate limit.

<Sysname> system-view

[Sysname] arp rate-limit log enable

arp rate-limit log interval

Use arp rate-limit log interval to set the notification and log message sending interval for ARP packet rate limit.

Use undo arp rate-limit log interval to restore the default.

Syntax

arp rate-limit log interval interval

undo arp rate-limit log interval

Default

The device sends notifications or log messages every 60 seconds when the rate of ARP packets received on an interface exceeds the limit.

Views

System view

Predefined user roles

network-admin

Parameters

interval: Specifies an interval in the range of 1 to 86400 seconds.

Usage guidelines

To change the default interval and activate it, you must enable ARP packet rate limit and enable sending notifications or log messages for ARP packet rate limit.

Examples

# Set the device to send notifications and log messages every 120 seconds when the rate of ARP packets received on an interface exceeds the limit.

<Sysname> system-view

[Sysname] arp rate-limit log interval 120

Related commands

arp rate-limit

arp rate-limit log enable

snmp-agent trap enable arp

ARP SNMP notification commands

snmp-agent trap enable arp

Use snmp-agent trap enable arp to enable SNMP notifications for ARP.

Use undo snmp-agent trap enable arp to disable SNMP notifications for ARP.

Syntax

Default

SNMP notifications for ARP are disabled.

Views

System view

Predefined user roles

network-admin

Parameters

active-ack: Specifies ARP active acknowledgement notifications.

arp-miss: Specifies rate limit notifications for sending ARP Miss messages or ARP packets.

entry-check: Specifies ARP entry modification notifications.

entry-limit: Specifies ARP entry limit notifications.

gateway-check: Specifies ARP gateway protection notifications.

local-conflict: Specifies endpoint and local device conflict notifications.

mac-mismatch: Specifies MAC address inconsistency notifications.

packet-check: Specifies invalid ARP packet check notifications.

rate-limit: Specifies rate limit notifications for receiving ARP packets.

user-ip-conflict: Specifies user IP address conflict notifications.

user-move: Specifies user port migration notifications.

Usage guidelines

Enable SNMP notifications for ARP as required.

· If you enable ARP active acknowledgement notifications, the device sends a notification to the SNMP module when it does not establish an ARP entry due to active acknowledgement. The notification includes the sender IP address in the received ARP packet and the interface that receives the ARP packet.

· If you enable rate limit notifications for sending ARP Miss messages or ARP packets, the device sends the highest threshold-crossed rate as a notification to the SNMP module.

· If you enable ARP entry modification notifications, the device sends a notification to the SNMP module when it detects that the ARP entry for a user might be changed to the attacker's ARP entry. The notification includes the sender IP and MAC addresses in the ARP attack packet.

· If you enable ARP entry limit notifications, the device sends the current number of ARP entries as a notification to the SNMP module when the number of global ARP entries exceeds the alarm threshold.

· If you enable ARP gateway protection notifications, the device sends a notification to the SNMP module when it is attacked by gateway spoofing attacks. The notification includes the sender IP and MAC addresses in the ARP attack packet dropped by ARP gateway protection, and index of the interface that received the ARP attack packet. When an ARP packet with the same sender IP address triggers the SNMP notification again within 3 minutes, the device sends a recovery notification to the SNMP module.

· If you enable endpoint and local device conflict notifications, the device sends a notification to the SNMP module when an endpoint and local device conflict occurs. The notification includes the sender IP address, sender MAC address, target IP address, and target MAC address in the conflicting ARP packet.

· If you enable MAC address inconsistency notifications, the device sends a notification to the SNMP module when the MAC address in the configured static ARP entry and user's actual MAC address are inconsistent. The notification includes the IP address, VPN instance, and MAC address in the ARP entry.

· An invalid ARP packet contains an invalid hardware address type, protocol address type, hardware address length, protocol address length, operation code, or VLAN. For example, when the operation code value is not 1 (ARP request) or 2 (ARP reply), the operation code is invalid and the ARP packet is invalid. If you enable invalid ARP packet check notifications, the device sends a notification to the SNMP module when it receives an invalid ARP packet. The notification includes the name of the interface that received the ARP packet, sender MAC and IP addresses, user VLAN ID, and VLAN ID of the service provider.

· If you enable rate limit notifications for receiving ARP packets, the device sends the highest threshold-crossed rate as a notification to the SNMP module. For more information about ARP packet rate limit, see "ARP packet rate limit commands."

· If you enable user IP address conflict notifications, the device sends a notification to the SNMP module when a user IP address conflict occurs. The notification includes the sender IP and MAC addresses in the conflicting ARP packet, and MAC address in the corresponding local ARP entry. For more information about enabling recording user IP address conflicts, see ARP configuration in Layer 3—IP Services Configuration Guide.

· If you enable user port migration notifications, the device sends a notification to the SNMP module when a user port changes. The notification includes the IP address, MAC address, port before migration, and port after migration of the user. For more information about enabling recording user port migrations, see ARP configuration in Layer 3—IP Services Configuration Guide.

If you do not specify any keywords, this command enables all SNMP notifications for ARP.

For ARP event notifications to be sent correctly, you must also configure SNMP on the device. For more information about SNMP configuration, see Network Management and Monitoring Configuration Guide.

Examples

# Enable rate limit notifications for receiving ARP packets.

<Sysname> system-view

[Sysname] snmp-agent trap enable arp rate-limit

Source MAC-based ARP attack detection commands

arp source-mac

Use arp source-mac to enable the source MAC-based ARP attack detection feature and specify a handling method.

Use undo arp source-mac to disable the source MAC-based ARP attack detection feature.

Syntax

arp source-mac { filter | monitor }

undo arp source-mac [ filter | monitor ]

Default

The source MAC-based ARP attack detection feature is disabled.

Views

System view

Predefined user roles

network-admin

Parameters

filter: Specifies the filter handling method.

monitor: Specifies the monitor handling method.

Usage guidelines

Configure this feature on the gateways.

This feature checks the number of ARP packets delivered to the CPU. If the number of packets from the same MAC address within 5 seconds exceeds a threshold, the device generates an ARP attack entry for the MAC address. Before the entry ages out, the device handles the attack by using either of the following methods:

· Monitor—Only generates log messages.

· Filter—Generates log messages and filters out subsequent ARP packets from the MAC address.

Make sure you have enabled the ARP logging feature before enabling the source MAC-based ARP attack detection feature. For information about the ARP logging feature, see Layer 3—IP Services Configuration Guide.

If you do not specify any handling method in the undo arp source-mac command, the command disables this feature.

Examples

# Enable the source MAC-based ARP attack detection feature and specify the filter handling method.

<Sysname> system-view

[Sysname] arp source-mac filter

arp source-mac aging-time

Use arp source-mac aging-time to set the aging time for ARP attack entries.

Use undo arp source-mac aging-time to restore the default.

Syntax

arp source-mac aging-time time

undo arp source-mac aging-time

Default

The aging time for ARP attack entries is 300 seconds.

Views

System view

Predefined user roles

network-admin

Parameters

time: Sets the aging time for ARP attack entries, in the range of 60 to 6000 seconds.

Examples

# Set the aging time for ARP attack entries to 60 seconds.

<Sysname> system-view

[Sysname] arp source-mac aging-time 60

arp source-mac exclude-mac

Use arp source-mac exclude-mac to exclude specific MAC addresses from source MAC-based ARP attack detection.

Use undo arp source-mac exclude-mac to remove the excluded MAC addresses from source MAC-based ARP attack detection.

Syntax

arp source-mac exclude-mac mac-address&<1-n>

undo arp source-mac exclude-mac [ mac-address&<1-n> ]

Default

No MAC addresses are excluded from source MAC-based ARP attack detection.

Views

System view

Predefined user roles

network-admin

Parameters

mac-address&<1-n>: Specifies a MAC address list. The mac-address argument indicates an excluded MAC address in the format of H-H-H. &<1-n> indicates the number of excluded MAC addresses that you can configure. The value for n varies by device model.

Usage guidelines

If you do not specify a MAC address, the undo arp source-mac exclude-mac command removes all excluded MAC addresses.

Examples

# Exclude a MAC address from source MAC-based ARP attack detection.

<Sysname> system-view

[Sysname] arp source-mac exclude-mac 001e-1200-0213

arp source-mac threshold

Use arp source-mac threshold to set the threshold for source MAC-based ARP attack detection. If the number of ARP packets sent from a MAC address within 5 seconds exceeds this threshold, the device recognizes this as an attack.

Use undo arp source-mac threshold to restore the default.

Syntax

arp source-mac threshold threshold-value

undo arp source-mac threshold

Default

The threshold for source MAC-based ARP attack detection is 30.

Views

System view

Predefined user roles

network-admin

Parameters

threshold-value: Specifies the threshold for source MAC-based ARP attack detection. The value range is 1 to 5000.

Examples

# Set the threshold for source MAC-based ARP attack detection to 30.

<Sysname> system-view

[Sysname] arp source-mac threshold 30

display arp source-mac

Use display arp source-mac to display ARP attack entries detected by source MAC-based ARP attack detection.

Syntax

display arp source-mac { interface interface-type interface-number [ slot slot-number ] | slot slot-number }

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

interface interface-type interface-number: Specifies an interface by its type and number. If you specify a virtual interface, you can also specify a location on the device to display entries for the member physical interfaces that the virtual interface has at that location.

slot slot-number: Specifies the slot number of the device, which is fixed at 1.

Examples

# Display the ARP attack entries detected by source MAC-based ARP attack detection on GigabitEthernet 1/0/1.

<Sysname> display arp source-mac interface gigabitethernet 1/0/1

Source-MAC VLAN ID Interface Aging-time

23f3-1122-3344 4094 GE1/0/1 10

Table 2 Command output

Field	Description
Source-MAC	Source MAC address of the attack.
VLAN ID	ID of the VLAN in which the attack was detected.
Interface	Interface on which the attack was detected.
Aging-time	Aging time for the ARP attack entry, in minutes.

display arp source-mac statistics

Use display arp source-mac statistics to display statistics for packets dropped by source MAC-based ARP attack detection.

Syntax

display arp source-mac statistics slot slot-number

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

slot slot-number: Specifies the slot number of the device, which is fixed at 1.

Examples

# Display statistics for packets dropped by source MAC-based ARP attack detection.

<Sysname> display arp source-mac statistics

Dropped ARP packets:23321

Table 3 Command output

Field	Description
Dropped ARP packets	Number of packets dropped by source MAC-based ARP attack detection.

‌

Related commands

arp source-mac

reset arp source-mac statistics

Use reset arp source-mac statistics to clear statistics of packets dropped by source MAC-based ARP attack detection.

Syntax

reset arp source-mac statistics { all | [ slot slot-number ] }

Views

User view

Predefined user roles

network-admin

Parameters

all: Clear all statistics of packets.

slot slot-number: Specifies the slot number of the device, which is fixed at 1.

Usage guidelines

If you do not specify any parameter, the command clears all statistics of packets dropped by source MAC-based ARP attack detection.

Examples

# Clear all statistics of packets dropped by source MAC-based ARP attack detection.

<Sysname> reset arp source-mac statistics

Related commands

display arp source-mac statistics

ARP packet source MAC consistency check commands

arp valid-check enable

Use arp valid-check enable to enable ARP packet source MAC address consistency check.

Use undo arp valid-check enable to disable ARP packet source MAC address consistency check.

Syntax

arp valid-check enable

undo arp valid-check enable

Default

ARP packet source MAC address consistency check is disabled.

Views

System view

Predefined user roles

network-admin

Usage guidelines

Configure this feature on gateways. The gateways can filter out ARP packets whose source MAC address in the Ethernet header is different from the sender MAC address in the message body.

Examples

# Enable ARP packet source MAC address consistency check.

<Sysname> system-view

[Sysname] arp valid-check enable

display arp valid-check statistics

Use display arp valid-check statistics to display statistics for packets dropped by ARP packet source MAC address consistency check.

Syntax

display arp valid-check statistics slot slot-number

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

slot slot-number: Specifies the slot number of the device, which is fixed at 1.

Examples

# Display statistics for packets dropped by ARP packet source MAC address consistency check.

<Sysname> display arp valid-check statistics

Dropped ARP packets: 23321

Table 4 Command output

Field	Description
Dropped ARP packets	Number of packets dropped by ARP packet source MAC address consistency check.

‌

Related commands

arp valid-check enable

reset arp valid-check statistics

Use reset arp valid-check statistics to clear statistics for packets dropped by ARP packet source MAC address consistency check.

Syntax

reset arp valid-check statistics { all | slot slot-number }

Views

User view

Predefined user roles

network-admin

Parameters

all: Specifies all statistics for packets dropped by ARP packet source MAC address consistency check.

slot slot-number: Specifies the slot number of the device, which is fixed at 1.

Examples

# Clear statistics for packets dropped by ARP packet source MAC address consistency check.

<Sysname> reset arp valid-check statistics

Related commands

display arp valid-check statistics

ARP active acknowledgement commands

arp active-ack enable

Use arp active-ack enable to enable the ARP active acknowledgement feature.

Use undo arp active-ack enable to disable the ARP active acknowledgement feature.

Syntax

arp active-ack [ strict ] enable

undo arp active-ack [ strict ] enable

Default

The ARP active acknowledgement feature is disabled.

Views

System view

Predefined user roles

network-admin

Parameters

strict: Enables strict mode for ARP active acknowledgement.

Usage guidelines

Configure this feature on gateways to prevent user spoofing.

Examples

# Enable the ARP active acknowledgement feature.

<Sysname> system-view

[Sysname] arp active-ack enable

Authorized ARP commands

arp authorized enable

Use arp authorized enable to enable authorized ARP on an interface.

Use undo arp authorized enable to disable authorized ARP on an interface.

Syntax

arp authorized enable

undo arp authorized enable

Default

Authorized ARP is disabled on the interface.

Views

Layer 3 Ethernet interface view

Layer 3 Ethernet subinterface view

Layer 3 aggregate interface view

Layer 3 aggregate subinterface view

VSI interface view

VLAN interface view

Predefined user roles

network-admin

Examples

# Enable authorized ARP on VLAN-interface 200.

<Sysname> system-view

[Sysname] interface vlan-interface 200

[Sysname-Vlan-interface200] arp authorized enable

ARP scanning and fixed ARP commands

arp fixup

Use arp fixup to convert existing dynamic ARP entries to static ARP entries.

Use undo arp fixup to convert valid static ARP entries to dynamic ARP entries and delete invalid static ARP entries.

Syntax

arp fixup

undo arp fixup

Views

System view

Predefined user roles

network-admin

Usage guidelines

The ARP conversion is a one-time operation. You can use this command again to convert the dynamic ARP entries learned later to static.

The static ARP entries converted from dynamic ARP entries have the same attributes as the manually configured static ARP entries. Due to the device's limit on the total number of static ARP entries, some dynamic ARP entries might fail the conversion.

The static ARP entries after conversion can include the following entries:

· Existing dynamic and static ARP entries before conversion.

· New dynamic ARP entries learned during the conversion.

Dynamic ARP entries that are aged out during the conversion are not converted to static ARP entries.

To delete a static ARP entry changed from a dynamic one, use the undo arp ip-address [ vpn-instance-name ] command. To delete all such static ARP entries, use the reset arp all or reset arp static command.

Examples

# Convert existing dynamic ARP entries to static ARP entries.

<Sysname> system-view

[Sysname] arp fixup

This command will convert existing dynamic ARP entries to static ARP entries. Continue? [Y/N]:Y

Fixup ARP. Please wait...

Fixup is complete.

arp scan

Use arp scan to trigger an ARP scanning in an address range.

Syntax

arp scan [ start-ip-address to end-ip-address ]

Views

Layer 3 Ethernet interface view

Layer 3 Ethernet subinterface view

Layer 3 aggregate interface view

Layer 3 aggregate subinterface view

VSI interface view

VLAN interface view

Predefined user roles

network-admin

Parameters

start-ip-address: Specifies the start IP address of the scanning range.

end-ip-address: Specifies the end IP address of the scanning range. The end IP address must be higher than or equal to the start IP address.

Usage guidelines

CAUTION:

ARP scanning will take some time and occupy a lot of system and network resources. To stop an ongoing scan, press Ctrl + C. Dynamic ARP entries are created based on ARP replies received before the scan is terminated.

ARP scanning automatically creates ARP entries for devices in the specified address range. IP addresses already in existing ARP entries are not scanned.

If the interface's primary and secondary IP addresses are in the address range, the sender IP address in the ARP request is the address on the smallest network segment.

If no address range is specified, the device learns ARP entries for devices on the subnet where the primary IP address of the interface resides. The sender IP address in the ARP requests is the primary IP address of the interface.

The start and end IP addresses must be on the same subnet as the primary IP address or secondary IP addresses of the interface.

Examples

# Configure the device to scan the neighbors on the network where the primary IP address of VLAN-interface 2 resides.

<Sysname> system-view

[Sysname] interface vlan-interface 2

[Sysname-Vlan-interface2] arp scan

# Configure the device to scan neighbors in an address range.

<Sysname> system-view

[Sysname] interface vlan-interface 2

[Sysname-Vlan-interface2] arp scan 1.1.1.1 to 1.1.1.20

arp scan auto enable

Use arp scan auto enable to enable automatic ARP scanning in a specified address range on an interface.

Use undo arp scan auto enable to disable automatic ARP scanning or cancel specified ARP scanning range settings for subnets on an interface.

Syntax

arp scan auto enable [ start-ip-address to end-ip-address [ source-addr source-ip-address ] ]

undo arp scan auto enable [ start-ip-address to end-ip-address ]

Default

Automatic ARP scanning is disabled on an interface.

Views

Layer 3 Ethernet interface view

Layer 3 Ethernet subinterface view

Layer 3 aggregate interface view

Layer 3 aggregate subinterface view

VSI interface view

VLAN interface view

Predefined user roles

network-admin

Parameters

start-ip-address: Specifies the start IP address of the scanning range.

to end-ip-address: Specifies the end IP address of the scanning range. The end IP address must be higher than or equal to the start IP address. The maximum number of IP addresses in the IP range is 65535.

source-addr source-ip-address: Specifies the source address for the ARP requests. The source-ip-address argument can be any valid IP address. If you do not specify this option, the interface uses its IP address as the source address of the ARP requests.

Usage guidelines

Application scenarios

Automatic ARP scanning enables an interface to update its ARP entries in time. It automatically sends ARP requests to the IP addresses in the specified address range to create ARP entries for them. IP addresses that already have ARP entries are not scanned any more.

Operating mechanism

If you know the IP address range assigned to the neighbors on the LAN, you can specify the assigned IP address range as the ARP scanning range to shorten the scanning waiting time. You can use this command to specify a maximum of 16 scanning ranges for different subnets. The subnet addresses for each scanning range cannot overlap with each other.

If you specify the ARP scanning range without specifying the source address for ARP requests, the interface scans the IP address intersection of the scanning range and the subnet of the interface. If the interface is configured with IP addresses on different subnets that intersect with the scanning range, the device uses the target IP address in each ARP request to match the subnets. The source IP address is the IP address with the longest subnet mask on the matching subnet. If the subnet masks are of the same length, the source address is the primary IP address for the interface. If all IP addresses in the scanning range are on the same subnet of the interface, the source address is that subnet IP address.

If you specify the ARP scanning range and source address for the sending ARP requests, the interface scans all IP addresses in the scanning range without considering the subnet addresses of the interface.

If the ARP scanning range is not specified, the interface scans neighbors on the subnets where the primary IP address and secondary IP addresses of the interface reside. The source IP addresses for the ARP requests are the primary IP address and secondary IP addresses for the interface.

You can set the ARP request sending rate by using the arp scan auto send-rate command.

Restrictions and guidelines

If you trigger ARP scanning and enable automatic ARP scanning on an interface, both of them take effect. As a best practice, enable automatic ARP scanning only on networks where user come online and go offline frequently.

Examples

# Configure the device to automatically scan the neighbors on the network where the primary IP address of VLAN-interface 2 resides.

<Sysname> system-view

[Sysname] interface vlan-interface 2

[Sysname-Vlan-interface2] arp scan auto enable

Related commands

arp scan auto send-rate

Use arp scan auto send-rate to set the ARP packet sending rate for automatic ARP scanning.

Use undo arp scan auto send-rate to restore the default.

Syntax

arp scan auto send-rate { ppm ppm | pps }

undo arp scan auto send-rate

Default

The device sends ARP packets at the rate of 48 pps during automatic ARP scanning.

Views

System view

Predefined user roles

network-admin

Parameters

ppm ppm: Specifies the ARP packet sending rate, in packets per minute (ppm). The value range for the ppm argument is 10 to 600, and the value must be a multiple of 10.

pps: Specifies the ARP packet sending rate, in packets per second (pps). The value range for the pps argument is 10 to 1000, and the value must be a multiple of 10.

Usage guidelines

You can set the ARP packet sending rate if the scanning range has a large number of IP addresses. This setting can avoid high CPU usage and heavy network load caused by a burst of ARP traffic.

When you set the sending rate to a large value, the device might use a rate lower than the specified rate to ensure the device performance.

Examples

# Set the ARP packet sending rate to 10 pps during automatic ARP scanning.

<Sysname> system-view

[Sysname] arp scan auto send-rate 10

Related commands

arp scan auto enable

ARP gateway protection commands

arp filter source

Use arp filter source to enable ARP gateway protection for a gateway.

Use undo arp filter source to disable ARP gateway protection for a gateway.

Syntax

arp filter source ip-address

undo arp filter source ip-address

Default

ARP gateway protection is disabled.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Parameters

ip-address: Specifies the IP address of a protected gateway.

Usage guidelines

You can enable ARP gateway protection for a maximum of eight gateways on an interface.

You cannot configure both the arp filter source and arp filter binding commands on the same interface.

Examples

# Enable ARP gateway protection for the gateway with IP address 1.1.1.1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] arp filter source 1.1.1.1

ARP filtering commands

arp filter binding

Use arp filter binding to enable ARP filtering and configure an ARP permitted entry.

Use undo arp filter binding to remove an ARP permitted entry.

Syntax

arp filter binding ip-address mac-address

undo arp filter binding ip-address

Default

ARP filtering is disabled.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Predefined user roles

network-admin

Parameters

ip-address: Specifies a permitted sender IP address.

mac-address: Specifies a permitted sender MAC address.

Usage guidelines

If the sender IP and MAC addresses of an ARP packet match an ARP permitted entry, the ARP packet is permitted. If the sender IP and MAC addresses of an ARP packet do not match an ARP permitted entry, the ARP packet is discarded.

You can configure a maximum of eight ARP permitted entries on an interface.

You cannot configure both the arp filter source and arp filter binding commands on the same interface.

Examples

# Enable ARP filtering and configure an ARP permitted entry.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] arp filter binding 1.1.1.1 0e10-0213-1023

ARP packet sender IP address checking commands

arp sender-ip-range

Use arp sender-ip-range to specify the sender IP address range for ARP packet checking.

Use undo arp sender-ip-range to restore the default.

Syntax

arp sender-ip-range start-ip-address end-ip-address

undo arp sender-ip-range

Default

No sender IP address range is specified for ARP packet checking.

Views

VLAN view

Predefined user roles

network-admin

Parameters

start-ip-address: Specifies the start IP address.

end-ip-address: Specifies the end IP address. The end IP address must be higher than or equal to the start IP address.

Usage guidelines

The gateway discards an ARP packet if its sender IP address is not within the allowed IP address range.

If you execute this command multiple times, the most recent configuration takes effect.

Examples

# Specify the sender IP address range 1.1.1.1 to 1.1.1.20 for ARP packet checking in VLAN 2.

<Sysname> system-view

[Sysname] vlan 2

[Sysname–vlan2] arp sender-ip-range 1.1.1.1 1.1.1.20

12-Security Command Reference

display arp source-suppression

Application scenarios

Operating mechanism

Restrictions and guidelines

Intelligent Terminal Products

Product Support Services

Technical Service Solutions

Resource Center

Policy

Online Help

Become a Partner

Partner Policy & Program

Global Learning

Partner Sales Resources

Service Business

News & Events

Contact Us