Login
- Table of Contents
- Related Documents
-
| Title | Size | Download |
|---|---|---|
| 03-Hardware resource management commands | 223.07 KB |
Hardware resource management commands
display cpu-usage
Use display cpu-usage to display the current CPU usage statistics.
Syntax
display cpu-usage [ control-plane] [ summary ] [ slot slot-number [ cpu cpu-number ] ]
Views
Any view
Predefined user roles
network-admin
network-operator
Parameters
control-plane: Displays CPU usage statistics for the control plane.
summary: Displays CPU usage statistics in table form. If you do not specify this keyword, the command displays CPU usage statistics in text form.
slot slot-number: Specifies the slot number of the device, which is fixed at 1.
cpu cpu-number: Specifies a CPU by its number.
Usage guidelines
If two hyphens (--) are displayed for the CPU usage during the most recent 5-second, 1-minute, and 5-minute intervals, the command might fail to obtain data from the database on the device. Try the command later.
Examples
# Display the current CPU usage statistics in text form.
<Sysname> display cpu-usage
Slot 1 CPU 0 CPU usage:
1% in last 5 seconds
1% in last 1 minute
1% in last 5 minutes
# Display the current CPU usage statistics in table form.
<Sysname> display cpu-usage
Slot CPU Last 5 sec Last 1 min Last 5 min
1 0 17% 29% 28%
Table 1 Command output
|
Field |
Description |
|
x% in last 5 seconds Last 5 sec |
Average CPU usage during the most recent 5-second interval. |
|
y% in last 1 minute Last 1 min |
Average CPU usage during the most recent 1-minute interval. |
|
z% in last 5 minutes Last 5 min |
Average CPU usage during the most recent 5-minute interval. |
display cpu-usage configuration
Use display cpu-usage configuration to display CPU usage monitoring settings.
Syntax
display cpu-usage configuration [ slot slot-number [ cpu cpu-number ] ]
Views
Any view
Predefined user roles
network-admin
Parameters
slot slot-number: Specifies the slot number of the device, which is fixed at 1.
cpu cpu-number: Specifies a CPU by its number.
Examples
# Display the CPU usage monitoring settings.
<Sysname> display cpu-usage configuration
CPU usage monitor is enabled.
Current monitor interval is 60 seconds.
Current severe alarm threshold is 99%.
Current minor alarm threshold is 79%.
Table 2 Command output
|
Field |
Description |
|
CPU usage monitor is enabled. |
CPU usage tracking is enabled. |
|
Current monitor interval is 60 seconds. |
Sampling interval for CPU usage tracking is 60 seconds. |
Related commands
monitor cpu-usage enable
monitor cpu-usage interval
monitor cpu-usage threshold
display cpu-usage history
Use display cpu-usage history to display the historical CPU usage statistics in a coordinate system.
Syntax
display cpu-usage history [ job job-id ] [ slot slot-number [ cpu cpu-number ] ]
Views
Any view
Predefined user roles
network-admin
network-operator
Parameters
job job-id: Specifies a process by its ID. The value range for job-id is 1 to 2147483647. If you do not specify a process, this command displays the statistics for the entire system's CPU usage (the total CPU usage of all processes). To view the IDs and names of the running processes, use the display process command. For more information, see Network Management and Monitoring Command Reference.
slot slot-number: Specifies the slot number of the device, which is fixed at 1.
cpu cpu-number: Specifies a CPU by its number. If you specify a process but do not specify a CPU, this command displays the statistics for the default CPU. If you do not specify a process or CPU, this command displays the historical statistics for all CPUs.
Usage guidelines
After CPU usage tracking is enabled, the system regularly samples CPU usage and saves the samples to a buffer. This command displays the most recent 60 samples in a coordinate system as follows:
· The vertical axis represents the CPU usage. If a statistic is not a multiple of the usage step, it is rounded up or down to the closest multiple of the usage step. For example, if the CPU usage step is 5%, the statistic 53% is rounded up to 55%, and the statistic 52% is rounded down to 50%.
· The horizontal axis represents the time.
· Pound signs (#) indicate the CPU usage. The value on the vertical axis for the topmost pound sign at a specific time represents the CPU usage at that time.
Examples
# Display the historical CPU usage statistics.
<Sysname> display cpu-usage history
100%|
95%|
90%|
85%|
80%|
75%|
70%|
65%|
60%|
55%|
50%|
45%|
40%|
35%|
30%|
25%|
20%|
15%| #
10%| ### #
5%| ########
------------------------------------------------------------
10 20 30 40 50 60 (minutes)
cpu-usage (Slot 1 CPU 0) last 60 minutes (SYSTEM)
The output shows the following items:
· Process name. The name SYSTEM represents the entire system.
· CPU that is holding the process: CPU 0 in slot 1.
· Historical CPU usage statistics for the entire system during the last 60 minutes.
¡ 12 minutes ago—Approximately 5%.
¡ 13 minutes ago—Approximately 10%.
¡ 14 minutes ago—Approximately 15%.
¡ 15 minutes ago—Approximately 10%.
¡ 16 and 17 minutes ago—Approximately 5%.
¡ 18 minutes ago—Approximately 10%.
¡ 19 minutes ago—Approximately 5%.
¡ Other time—2% or lower.
monitor cpu-usage enable
monitor cpu-usage interval
display device
Use display device to display device hardware information.
Syntax
display device [ flash | usb ] [ slot slot-number [ subslot subslot-number ] | verbose ]
Views
Any view
Predefined user roles
network-admin
network-operator
Parameters
flash: Displays flash memory information.
usb: Displays USB interface information.
slot slot-number: Specifies the slot number of the device, which is fixed at 1.
subslot subslot-number: Specifies a subcard by its subslot number. If you do not specify a subcard, this command does not display information about any subcards.
verbose: Displays detailed information. If you do not specify this keyword, this command displays brief information, and does not display firewall card information.
Examples
# Display device hardware information.
<Sysname> display device
Slot 1
Slot Type State Subslot Soft Ver Patch Ver
1 S5580S-24T6X-EI Master 0 S5580S-1112 None
Table 3 Command output
|
Field |
Description |
|
Type |
Device type. |
|
State |
This field is not supported in the current software version. Role of the device in an IRF fabric: · Master—The device is the master. · Standby—The device is a subordinate member. |
|
Soft Ver |
Software version of the device. |
|
Patch Ver |
Most recently released patch image version that is running on the device. If no patch image is installed, this field displays None. If both incremental and non-incremental patch images are running on the device, this field displays the most recently released incremental patch image version. For more information about patch image types, see "Upgrading software." |
display device manuinfo
Use display device manuinfo to display hardware electronic label information for the device.
Syntax
display device manuinfo [ slot slot-number ]
Views
Any view
Predefined user roles
network-admin
network-operator
Parameters
slot slot-number: Specifies the slot number of the device, which is fixed at 1.
Usage guidelines
An electronic label contains the permanent configuration information, including the hardware serial number, manufacturing date, MAC address, and vendor name. The data is written to the storage component during hardware debugging or testing. This command displays only part of the electronic label information.
Examples
# Display hardware electronic label information for the device.
<Sysname> display device manuinfo
...
display device manuinfo fan
Use display device manuinfo fan to display electronic label information for a fan tray.
|
|
NOTE: Only the S5580X-EI switch series supports this command. |
Syntax
display device manuinfo slot slot-number fan fan-id
Views
Any view
Predefined user roles
network-admin
network-operator
Parameters
slot slot-number: Specifies the slot number of the device, which is fixed at 1.
fan-id: Specifies a fan tray by its ID.
Examples
# Display electronic label information for a fan tray.
<Sysname> display device manuinfo fan 1
...
display device manuinfo power
Use display device manuinfo power to display electronic label information for a power module.
Syntax
display device manuinfo slot slot-number power power-id
Views
Any view
Predefined user roles
network-admin
network-operator
Parameters
slot slot-number: Specifies the slot number of the device, which is fixed at 1.
power-id: Specifies a power module by its ID.
Examples
# Display electronic label information for a power module.
<Sysname> display device manuinfo slot 1 power 1
...
display environment
Use display environment to display temperature information.
Syntax
display environment [ slot slot-number ]
Views
Any view
Predefined user roles
network-admin
network-operator
Parameters
slot slot-number: Specifies the slot number of the device, which is fixed at 1.
Examples
# Display information about all temperature sensors on the device.
<Sysname> display environment
System temperature information (degree centigrade):
----------------------------------------------------------------------
Slot Sensor Temperature Lower Warning Alarm Shutdown
1 hotspot 1 53 0 80 92 NA
Table 4 Command output
|
Field |
Description |
|
System Temperature information (degree centigrade) |
Temperature information (°C). |
|
sensor |
Temperature sensor: hotspot—Hotspot sensor. |
|
Slot |
Sensor position. |
|
Temperature |
Current temperature. |
|
Lower |
Lower temperature limit. If the device does not support this field, this field displays NA. |
|
Warning |
Warning temperature threshold. If the device does not support this field, this field displays NA. |
|
Alarm |
Alarming temperature threshold. If the device does not support this field, this field displays NA. |
|
Shutdown |
Shutdown temperature threshold. When the sensor temperature reaches the limit, the system shuts down automatically. If the device does not support this field, this field displays NA. |
display fan
Use display fan to display fan tray operating status information.
Syntax
display fan [ slot slot-number [ fan-id ] ]
Views
Any view
Predefined user roles
network-admin
network-operator
Parameters
slot slot-number: Specifies the slot number of the device, which is fixed at 1.
fan-id: Specifies a fan tray by its ID. If you do not specify a fan tray, this command displays operating status information for all fan trays at the specified position.
Examples
# Display the operating states of all fan trays.
<Sysname> display fan
Fan 1:
State : Normal
Airflow Direction: Fan-Panel-Exhaust
Fan 2:
State : Normal
Airflow Direction: Fan-Panel-Exhaust
Table 5 Command output
|
Field |
Description |
|
Fan 1 |
Fan tray number. |
|
State |
Fan tray status: · Absent—The slot is not installed with a fan tray. · Fault—The fan tray is faulty. · Normal—The fan tray is operating correctly. · FanDirectionFault—The actual airflow direction is not the preferred direction. |
|
Airflow Direction |
This field is supported only on the S5580X-EI switch series. Actual airflow direction: · Fan-Panel-Exhaust—Airflow exhaust on the fan panel side. · Fan-Panel-Intake—Airflow intake on the fan panel side. |
display hardware-mode status
Use display hardware-mode status to display the hardware resource mode for MAC address entries, ARP/ND entries, and routing entries.
|
|
NOTE: Only the S5580X-HI switch series supports this command. |
Syntax
display hardware-mode status
Views
Any view
Predefined user roles
network-admin
network-operator
Examples
# Specify the hardware resource mode for MAC address entries, ARP/ND entries, and routing entries
<H3C> display hardware-mode status
mode | Route-v4 | Route-v6 | MAC | ARP | ND
mode in use: 0 NORMAL 116K 58K 128K 80K 58K
mode for next reboot: 1 ROUTE 266K 133K 32K 32K 25K
Table 6 Command output
|
Field |
Description |
|
mode in use |
Current hardware resource mode for MAC address entries, ARP/ND entries, and routing entries. |
|
mode for next reboot |
Hardware resource mode for MAC address entries, ARP/ND entries, and routing entries after the device reboots. |
|
mode |
Hardware resource mode for MAC address entries, ARP/ND entries, and routing entries. |
|
Route-v4 |
Number of IPv4 routing entries. |
|
Route-v6 |
Number of IPv6 routing entries. |
|
MAC |
Number of MAC address entries. |
|
ARP |
Number of ARP entries. |
|
ND |
Number of ND entries. |
Related commands
hardware-mode
display memory
Use display memory to display memory usage information.
Syntax
display memory [ summary ] [ slot slot-number [ cpu cpu-number ] ]
Views
Any view
Predefined user roles
network-admin
network-operator
Parameters
summary: Displays brief information about memory usage. If you do not specify this keyword, the command displays detailed information about memory usage.
slot slot-number: Specifies the slot number of the device, which is fixed at 1.
cpu cpu-number: Specifies a CPU by its number.
Usage guidelines
If two hyphens (--) are displayed for all the fields in a line of the output, the command might fail to obtain data from the database on the device. Try the command later.
Examples
# Display detailed memory usage information.
<Sysname> display memory
Memory statistics are measured in KB:
Slot 1:
Total Used Free Shared Buffers Cached FreeRatio
Mem: 1990672 1549824 440848 0 74504 383792 27.4%
-/+ Buffers/Cache: 1091528 899144
Swap: 0 0 0
Container memory statistics are measured in KB:
Slot 1:
Total Used Free UsageRatio
Mem: 1990672 1222412 440848 61.4%
# Display brief memory usage information.
<Sysname> display memory summary
Memory statistics are measured in KB(Available):
Slot CPU Total Used Free Buffers Caches FreeRatio
0 0 16335164 4144720 12190444 8596 2472508 77.5%
Container memory statistics are measured in KB(Available):
Slot CPU Total Used Free UsageRatio
0 0 16335164 2358048 12190444 14.4%
Table 7 Command output
|
Field |
Description |
|
Memory statistics are measured in KB(Available) |
Usage information of the available memory on the physical device, in KB. |
|
Mem |
Memory usage information. |
|
Total |
Total size of the physical memory space that can be allocated. The memory space is virtually divided into two parts. Part 1 is solely used for kernel code, kernel management, and ISSU functions. Part 2 can be allocated and used for such tasks as running service modules and storing files. The size of part 2 equals the total size minus the size of part 1. |
|
Used |
Used physical memory. |
|
Free |
Free physical memory. |
|
Shared |
Physical memory shared by processes. If this field is not supported, two hyphens (--) are displayed. |
|
Buffers |
Physical memory used for buffers. If this field is not supported, two hyphens (--) are displayed. |
|
Cached Caches |
Physical memory used for caches. If this field is not supported, two hyphens (--) are displayed. |
|
FreeRatio |
Free memory ratio. |
|
-/+ Buffers/Cache |
-/+ Buffers/Cache:used = Mem:Used – Mem:Buffers – Mem:Cached, which indicates the physical memory used by applications. -/+ Buffers/Cache:free = Mem:Free + Mem:Buffers + Mem:Cached, which indicates the physical memory available for applications. |
|
Swap |
Memory space for swapping. |
|
Container memory statistics are measured in KB(Available) |
Container usage information of the available memory, including: · Total—Total size of the physical memory space that can be allocated in the Comware container, in KB. · Used—Used physical memory in the Comware container, in KB. · Free—Free physical memory in the Comware container, in KB. · UsageRatio—Free physical memory usage in the Comware container. |
display memory-threshold
Use display memory-threshold to display memory alarm thresholds and statistics.
Syntax
display memory-threshold [ slot slot-number [ cpu cpu-number ] ]
Views
Any view
Predefined user roles
network-admin
network-operator
Parameters
slot slot-number: Specifies the slot number of the device, which is fixed at 1.
cpu cpu-number: Specifies a CPU by its number.
Usage guidelines
For more information about memory usage notifications, see log information containing MEM_EXCEED_THRESHOLD or MEM_BELOW_THRESHOLD.
Examples
# Display memory alarm thresholds and statistics.
<Sysname> display memory-threshold
Memory usage threshold: 100%
Free memory threshold:
Minor: 256M
Severe: 192M
Critical: 128M
Normal: 320M
Current memory state: Normal
Event statistics:
[Back to normal state]
First notification: 0.0
Latest notification: 0.0
Total number of notifications sent: 0
[Enter minor low-memory state]
First notification at: 0.0
Latest notification at: 0.0
Total number of notifications sent: 0
[Back to minor low-memory state]
First notification at: 0.0
Latest notification at: 0.0
Total number of notifications sent: 0
[Enter severe low-memory state]
First notification at: 0.0
Latest notification at: 0.0
Total number of notifications sent: 0
[Back to severe low-memory state]
First notification at: 0.0
Latest notification at: 0.0
Total number of notifications sent: 0
[Enter critical low-memory state]
First notification at: 0.0
Latest notification at: 0.0
Total number of notifications sent: 0
display power
Use display power to display power module information.
Syntax
display power [ slot slot-number [ power-id ] ]
Views
Any view
Predefined user roles
network-admin
network-operator
Parameters
slot slot-number: Specifies the slot number of the device, which is fixed at 1.
power-id: Specifies a power module by its ID. If you do not specify a power module, this command displays information about all power modules at the specified position.
Examples
# Display brief power module information.
<Sysname> display power
PowerID State Mode Current(A) Voltage(V) Power(W) FanDirection
1 Absent -- -- -- -- --
2 Normal AC -- -- -- --
Table 8 Command output
|
Field |
Description |
|
PowerID |
Power module ID. |
|
State |
Power module status. · Absent—The slot is not installed with a power module. · Fault—The power module is faulty. · Normal—The power module is operating correctly. |
|
Mode |
Mode of the power module: · AC—AC power module. · DC—DC power module. |
|
Current(A) |
Output current of the power module, in amperes. If this field is not supported, two hyphens (--) are displayed. |
|
Voltage(V) |
Output voltage of the power module, in volts. If this field is not supported, two hyphens (--) are displayed. |
|
Power(W) |
Output power of the power module, in watts. If this field is not supported, two hyphens (--) are displayed. |
|
FanDirection |
Airflow direction of the power module: · PowerToPort—From the power module side to the port side. · PortToPower—From the port side to the power module side. |
display transceiver alarm
Use display transceiver alarm to display transceiver alarms.
Syntax
display transceiver alarm interface [ interface-type interface-number ]
Views
Any view
Predefined user roles
network-admin
network-operator
Parameters
interface [ interface-type interface-number ]: Specifies an interface by its type and number. If no interface is specified, this command displays the alarms present on every transceiver module.
Usage guidelines
Table 9 shows the common transceiver alarm components. If no error occurs, "None" is displayed.
Table 9 Common transceiver alarm components
|
Field |
Description |
|
APD |
Avalanche photo diode |
|
PCS |
Physical coding sublayer |
|
PHY XS |
PHY extended sublayer |
|
PMA/PMD |
Physical medium attachment/physical medium dependent |
|
power |
Optical power |
|
REFCLK |
Reference clock |
|
RX |
Receive |
|
TEC |
Thermoelectric cooler |
|
Temp |
Temperature |
|
TX |
Transmit |
|
WIS |
WAN interface sublayer |
|
FEC |
Forward error correction |
|
BER |
Bit error ratio |
|
CFO |
Carrier frequency offset |
Examples
# Display the alarms present on the transceiver module in interface GigabitEthernet 1/0/1.
<Sysname> display transceiver alarm interface gigabitethernet 1/0/1
GigabitEthernet1/0/1 transceiver current alarm information:
RX loss of signal
RX power low
Table 10 Command output
|
Field |
Description |
|
transceiver current alarm information |
Alarms present on the transceiver module. |
|
RX loss of signal |
Received signals are lost. |
|
RX power low |
Received power is low. |
display transceiver diagnosis
Use display transceiver diagnosis to display the current values of the digital diagnosis parameters on transceiver modules.
Syntax
display transceiver diagnosis interface [ interface-type interface-number ]
Views
Any view
Predefined user roles
network-admin
network-operator
Parameters
interface [ interface-type interface-number ]: Specifies an interface by its type and number. If no interface is specified, this command displays the current values of the digital diagnosis parameters on every transceiver module.
Examples
# Display the current values of the digital diagnosis parameters on the transceiver module in interface GigabitEthernet 1/0/1.
<Sysname> display transceiver diagnosis interface gigabitethernet 1/0/1
GigabitEthernet1/0/1 transceiver diagnostic information:
Current diagnostic parameters:
Temp(C) Voltage(V) Bias(mA) RX power(dBm) TX power(dBm)
36 3.31 6.13 -35.64 -5.19
Alarm thresholds:
Temp(C) Voltage(V) Bias(mA) RX power(dBM) TX power(dBM)
High 50 3.55 1.44 -10.00 5.00
Low 30 3.01 1.01 -30.00 0.00
Table 11 Command output
|
Field |
Description |
|
transceiver diagnostic information |
Digital diagnosis information for the transceiver module in the interface. |
|
Temp.(C) |
Temperature in °C, accurate to 1°C. |
|
Voltage(V) |
Voltage in V, accurate to 0.01 V. |
|
Bias(mA) |
Bias current in mA, accurate to 0.01 mA. |
|
RX power(dBm) |
Receive power in dBm, accurate to 0.01 dBm. |
|
TX power(dBm) |
Transmit power in dBm, accurate to 0.01 dBm. |
display transceiver interface
Use display transceiver interface to display the key parameters of transceiver modules.
Syntax
display transceiver interface [ interface-type interface-number ]
Views
Any view
Predefined user roles
network-admin
network-operator
Parameters
interface-type interface-number: Specifies an interface by its type and number. If you do not specify an interface, this command displays the key parameters of every transceiver module.
Examples
# Display the key parameters of the transceiver module in interface GigabitEthernet 1/0/1.
<Sysname> display transceiver interface gigabitethernet 1/0/1
GigabitEthernet1/0/1 transceiver information:
Transceiver type : 400G_BASE_SR8_QSFPDD
Connector type : MPO
Wavelength (nm) : 850
Transfer distance (m) : 70(OM3),100(OM4)
Max power(W) : 12
Digital diagnostic monitoring : Yes
Vendor name : H3C
Table 12 Command output
|
Field |
Description |
|
Transceiver Type |
Model of the transceiver module. |
|
Connector Type |
Connector type of the transceiver module: · Optical connectors, including SC connector developed by NTT, and 1.25mm/RJ45 LC connector developed by Lucent. · Other connectors, including RJ-45 and CX4. |
|
Wavelength(nm) |
For the transceiver module, this field displays central wavelength of the laser sent, in nm. If the transceiver module such as 10GBASE-LX4, supports multiple wavelengths, each wavelength value is separated by a comma. For the electrical transceiver, this field displays N/A. |
|
Transfer Distance(xx) |
Transfer distance. For a single-mode transceiver module, the distance is measured in km. For other transceiver modules, the distance is measured in m. If the transceiver module supports multiple transfer media, the transfer distances are separated by commas. The corresponding transfer medium is enclosed in the brackets following the transfer distance value. The following are the transfer media: · 9um—9/125um single-mode optical fiber. · 50um—50/125um OM 2 multi-mode optical fiber. · 62.5um—62.5/125um OM 1 multi-mode optical fiber. · CX4—CX4 cable. · OM3—50 um OM3 multi-mode optical fiber. · OM4—50 um OM4 multi-mode optical fiber. · OM5—50 um OM5 multi-mode optical fiber. · STACK—Stack cable. · TP—Twisted pair cable. |
|
Max power(W) |
Maximum power of the transceiver module. |
|
Digital Diagnostic Monitoring |
Support for digital diagnostic monitoring: · Yes. · No. |
|
Vendor Name |
Vendor name or vendor name specified for the transceiver module. |
|
Ordering Name |
Ordering name of the transceiver module. |
display transceiver manuinfo
Use display transceiver manuinfo to display electronic label information for transceiver modules.
Syntax
display transceiver manuinfo interface [ interface-type interface-number ]
Views
Any view
Predefined user roles
network-admin
network-operator
Parameters
interface [ interface-type interface-number ]: Specifies an interface by its type and number. If no interface is specified, this command displays electronic label information for the transceiver modules on all interfaces.
Examples
# Display electronic label information for the transceiver module in interface GigabitEthernet 1/0/1.
<Sysname> display transceiver manuinfo interface gigabitethernet 1/0/1
GigabitEthernet1/0/1 transceiver manufacture information:
Manu. Serial Number : 213410A0000054000251
Manufacturing Date : 2019-09-01
Vendor Name : H3C
Table 13 Command output
|
Field |
Description |
|
Manu. Serial Number |
Serial number generated during debugging and testing. |
|
Manufacturing Date |
Debugging and testing date. The date takes the value of the system clock of the computer when debugging and testing is performed. |
|
Vendor Name |
The value is H3C. |
hardware-mode
Use hardware-mode to specify the hardware resource mode for MAC address entries, APR/ND entries, and routing entries.
|
|
NOTE: Only the S5580X-HI switch series supports this command. |
Syntax
hardware-mode { 0 | 1 | 2 }
Default
The normal hardware resource mode applies.
Views
System view
Predefined user roles
network-admin
Parameters
0: Specifies the normal hardware resource mode for MAC address entries, APR/ND entries, and routing entries.
1: Specifies the routing hardware resource mode for MAC address entries, APR/ND entries, and routing entries.
2: Specifies the MAC hardware resource mode for MAC address entries, APR/ND entries, and routing entries.
Usage guidelines
The quantities of MAC address entries, APR/ND entries, and routing entries supported by the device vary by hardware resource mode. For more information, see the device management configuration in Fundamentals Configuration Guide.
For the command to take effect, you must save the configuration and reboot the device. Before rebooting the device, evaluate the impact on the network and make preparations.
Examples
# Specify the routing hardware resource mode for MAC address entries, APR/ND entries, and routing entries.
<Sysname> system-view
[Sysname] hardware-mode 1
Reboot device to make the configuration take effect.
Related commands
display hardware-mode status
memory-threshold
Use memory-threshold to set free-memory thresholds.
Use undo memory-threshold to restore the default.
Syntax
memory-threshold [ slot slot-number [ cpu cpu-number ] ] [ ratio ] minor minor-value severe severe-value critical critical-value normal normal-value
undo memory-threshold [ slot slot-number [ cpu cpu-number ] ]
Default
Minor alarm threshold: 256 MB.
Severe alarm threshold: 192 MB.
Critical alarm threshold: 128 MB.
Normal state threshold: 320 MB.
Views
System view
Predefined user roles
network-admin
Parameters
ratio: Specifies free-memory thresholds in percentage. If you do not specify this keyword, the command sets free-memory thresholds in MB.
minor minor-value: Specifies the minor alarm threshold. To view the value range for this threshold, enter a question mark (?) in the place of the minor-value argument. Setting this threshold to 0 disables the minor alarm feature.
severe severe-value: Specifies the severe alarm threshold. To view the value range for this threshold, enter a question mark (?) in the place of the severe-value argument. Setting this threshold to 0 disables the severe alarm feature.
critical critical-value: Specifies the critical alarm threshold. To view the value range for this threshold, enter a question mark (?) in the place of the critical-value argument. Setting this threshold to 0 disables the critical alarm feature.
normal normal-value: Specifies the normal state threshold. To view the value range for this threshold, enter a question mark (?) in the place of the normal-value argument.
slot slot-number: Specifies the slot number of the device, which is fixed at 1.
cpu cpu-number: Specifies a CPU by its number.
Usage guidelines
To ensure correct operation and improve memory efficiency, the system monitors the amount of free memory space in real time. If the amount of free memory space decreases to or below the minor, severe, or critical alarm threshold, the system issues an alarm to affected service modules or processes.
You can use the display memory command to display memory usage information.
If a memory alarm occurs, delete unused configuration items or disable some features to increase the free memory space. Because the memory space is insufficient, some configuration items might not be able to be deleted.
For more information about the thresholds, see Fundamentals Configuration Guide.
The system will restart a card if one of the following conditions is met:
· After a critical alarm occurs, the remaining free-memory value has been smaller than the critical alarm threshold for 30 seconds.
· The interval between two consecutive critical alarms is shorter than 30 seconds.
· The critical alarm has occurred three times within three minutes.
· After a critical alarm occurs, the system will periodically sample free memory space and predict if the free memory space will be exhausted within 30 seconds. If the prediction result indicates that the free memory space will be exhausted within 30 seconds, the system will restart the card.
Once the free memory space reaches the minor, severe, or critical alarm threshold, the device will display the current memory usage information when you log in to the device through console or Telnet login, and execute every command.
If the free memory space has been smaller than the minor alarm threshold for 12 hours, the system will report a minor memory event. If the free memory space has been smaller than the severe alarm threshold for 3 hours, the system will report a severe memory event. If the free memory space has been smaller than the critical alarm threshold for 1 hour, the system will report a critical memory event.
# Set the minor alarm, severe alarm, critical alarm, and normal state thresholds to 64 MB, 48 MB, 32 MB, and 96 MB, respectively.
<Sysname> system-view
[Sysname] memory-threshold minor 64 severe 48 critical 32 normal 96
# Set the minor alarm, severe alarm, critical alarm, and normal state thresholds to 3%, 2%, 1%, and 5% of the total memory size, respectively.
<Sysname> system-view
[Sysname] memory-threshold ratio minor 3 severe 2 critical 1 normal 5
Related commands
display memory-threshold
memory-threshold usage
Use memory-threshold usage to set the memory usage threshold.
Use undo memory-threshold usage to restore the default.
Syntax
memory-threshold [ slot slot-number [ cpu cpu-number ] ] usage memory-threshold
undo memory-threshold [ slot slot-number [ cpu cpu-number ] ] usage
Default
The memory usage threshold is 100%.
Views
System view
Predefined user roles
network-admin
Parameters
slot slot-number: Specifies the slot number of the device, which is fixed at 1.
cpu cpu-number: Specifies a CPU by its number.
memory-threshold: Specifies the memory usage threshold in percentage. The value range is 0 to 100.
Usage guidelines
The device samples memory usage at 1-minute intervals. If the sample is greater than the memory usage threshold, the device sends a trap.
Examples
# Set the memory usage threshold to 80%.
<Sysname> system-view
[Sysname] memory-threshold usage 80
Related commands
display memory-threshold
monitor cpu-usage enable
Use monitor cpu-usage enable to enable CPU usage tracking.
Use undo monitor cpu-usage enable to disable CPU usage tracking.
Syntax
monitor cpu-usage enable [ slot slot-number [ cpu cpu-number ] ]
undo monitor cpu-usage enable [ slot slot-number [ cpu cpu-number ] ]
Default
CPU usage tracking is enabled.
Views
System view
Predefined user roles
network-admin
Parameters
slot slot-number: Specifies the slot number of the device, which is fixed at 1.
cpu cpu-number: Specifies a CPU by its number.
Usage guidelines
After you enable CPU usage tracking, the system samples and saves CPU usage at the interval specified by the monitor cpu-usage interval command. You can use the display cpu-usage history command to view recent CPU usage.
Examples
# Enable CPU usage tracking.
<Sysname> system-view
[Sysname] monitor cpu-usage enable
display cpu-usage configuration
display cpu-usage history
monitor cpu-usage interval
monitor cpu-usage interval
Use monitor cpu-usage interval to set the sampling interval for CPU usage monitoring.
Use undo monitor cpu-usage interval to restore the default.
Syntax
monitor cpu-usage interval interval [ slot slot-number [ cpu cpu-number ] ]
undo monitor cpu-usage interval [ slot slot-number [ cpu cpu-number ] ]
Default
The system samples CPU usage every 1 minute.
Views
System view
Predefined user roles
network-admin
Parameters
interval: Specifies the sampling interval for CPU usage monitoring. Valid values include 5Sec (5 seconds), 1Min (1 minute), and 5Min (5 minutes), case insensitive.
slot slot-number: Specifies the slot number of the device, which is fixed at 1.
cpu cpu-number: Specifies a CPU by its number.
Usage guidelines
After CPU usage monitoring is enabled, the system samples and saves CPU usage at the specified interval. You can use the display cpu-usage history command to view recent CPU usage.
Examples
# Set the sampling interval for CPU usage monitoring to 5 seconds.
<Sysname> system-view
[Sysname] monitor cpu-usage interval 5Sec
Related commands
display cpu-usage configuration
display cpu-usage history
monitor cpu-usage enable
monitor resend cpu-usage
Use monitor resend cpu-usage to set CPU usage alarm resending intervals.
Use undo monitor resend cpu-usage to restore the default.
Syntax
monitor resend cpu-usage { minor-interval minor-interval | severe-interval severe-interval } * [ slot slot-number [ cpu cpu-number ] ]
undo monitor resend cpu-usage [ minor-interval | severe-interval ] [ slot slot-number [ cpu cpu-number ] ]
Default
The minor CPU usage alarm resending interval is 300 seconds. The severe CPU usage alarm resending interval is 60 seconds.
Views
System view
Predefined user roles
network-admin
Parameters
minor-interval minor-interval: Specifies the minor CPU usage alarm resending interval in seconds, a multiple of 5 in the range of 10 to 3600.
severe-interval severe-interval: Specifies the severe CPU usage alarm resending interval in seconds, a multiple of 5 in the range of 10 to 3600.
slot slot-number: Specifies the slot number of the device, which is fixed at 1.
cpu cpu-number: Specifies a CPU by its number.
Usage guidelines
The device samples CPU usage at intervals, and compares the samples with CPU usage thresholds to identify the CPU usage status and send alarms or notifications accordingly.
In minor alarm state, the device sends minor alarms periodically until the CPU usage increases above the severe threshold or the minor alarm is removed. In severe alarm state, the device sends severe alarms periodically until the severe alarm is removed. This command sets the alarm resending intervals.
If you do not specify a keyword for the undo monitor resend cpu-usage command, the command restores the default minor and severe CPU usage alarm resending intervals.
Examples
# Set the minor CPU usage alarm resending interval to 60 seconds for a slot.
<Sysname> system-view
[Sysname] monitor resend cpu-usage minor-interval 60 slot 1 cpu 0
shutdown-interval
Use shutdown-interval to set the port status detection timer.
Use undo shutdown-interval to restore the default.
Syntax
shutdown-interval interval
undo shutdown-interval
Default
The port status detection timer setting is 30 seconds.
Views
System view
Predefined user roles
network-admin
Parameters
interval: Specifies the port status detection timer value in seconds. The value range is 0 to 300. The value of 0 indicates that port status detection is not automatically performed, and you need to execute the undo shutdown command to restore the port status manually.
Usage guidelines
The device starts a port status detection timer when a port is shut down by a protocol. If the port has been in down state before the timer expires, the device will set the port status to the port's physical status.
If you change the timer setting during port detection, the device compares the new setting (T1) with the time that elapsed since the port was shut down (T).
If T < T1, the port will be brought up after T1 – T seconds.
If T ≥ T1, the port is brought up immediately.
For example, the timer setting is 30 seconds. If you change it to 10 seconds 2 seconds after the port is shut down, the port will come up 8 seconds later. If you change the timer setting to 2 seconds 10 seconds after the port is shut down, the port comes up immediately.
Examples
# Set the port status detection timer to 100 seconds.
<Sysname> system-view
[Sysname] shutdown-interval 100
temperature-limit
Use temperature-limit to set the temperature alarm thresholds.
Use undo temperature-limit to restore the default.
Syntax
temperature-limit slot slot-number { hotspot } sensor-number lowlimit warninglimit [ alarmlimit ]
undo temperature-limit slot slot-number { hotspot } sensor-number
Default
The default varies by temperature sensor model. To view the default, execute the undo temperature-limit and display environment commands in turn.
Views
System view
Predefined user roles
network-admin
Parameters
slot slot-number: Specifies the slot number of the device, which is fixed at 1.
hotspot: Configures temperature alarm thresholds for hotspot sensors. A hotspot sensor is typically near the chip that generates a great amount of heat and used to monitor the chip.
sensor-number: Specifies a sensor by its number. To view the value range, enter a question mark (?) in the place of this argument.
lowlimit: Specifies the low-temperature threshold in Celsius degrees. The value range varies by temperature sensor. To view the value range, enter a question mark (?) in the place of this argument.
warninglimit: Specifies the high-temperature warning threshold in Celsius degrees. This threshold must be greater than the low-temperature threshold. To view the value range, enter a question mark (?) in the place of this argument.
alarmlimit: Specifies the high-temperature alarming threshold in Celsius degrees. This threshold must be greater than the warning threshold. To view the value range, enter a question mark (?) in the place of this argument.
Usage guidelines
When the device temperature drops below the low-temperature threshold or reaches the high-temperature warning or alarming threshold, the device performs the following operations:
· Sends log messages and traps.
· Sets LEDs on the device panel.
Examples
# Set temperature alarm thresholds for hotspot sensor 1 in a slot.
<Sysname> system-view
[Sysname] temperature-limit slot 1 hotspot 1 -10 50 60
Related commands
display environment
