Contents

Tunnel policy commands· 1

display mpls tunnel 1

display tunnel-policy· 2

select-seq load-balance-number 3

tunnel-policy (system view) 4

 

Tunnel policy commands

Only advanced mode supports tunnel policies. For more information about system operating modes, see device management in Fundamentals Configuration Guide.

Layer 3 aggregate interfaces do not support tunnel policies. The device does not support MPLS forwarding for tunnel packets.

display mpls tunnel

Use display mpls tunnel to display tunnel information.

Syntax

display mpls tunnel { all | statistics | [ vpn-instance vpn-instance-name ] destination ipv4-address }

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

all: Displays all tunnels.

statistics: Displays tunnel statistics.

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, this command displays tunnel information for the public network.

destination: Displays the tunnel destined for the specified address.

ipv4-address: Specifies the tunnel destination IPv4 address.

Examples

# Display information about all tunnels.

<Sysname> display mpls tunnel all

Destination      Type     Tunnel/NHLFE      VPN Instance

2.2.2.2          LSP      NHLFE1024         -

Table 1 Command output

Field	Description
Destination	Tunnel destination address.
Type	Tunnel type: LSP
Tunnel/NHLFE	Tunnel or NHLFE entry. NHLFEnumber represents the ingress LSP that matches the NHLFE entry with NID of number.
VPN Instance	VPN instance name. If the tunnel belongs to the public network, this field displays a hyphen (-).

‌

# Display tunnel statistics.

<Sysname> display mpls tunnel statistics

LSP  :     1

GRE  :     0

CRLSP:     0

SRLSP:     0

Table 2 Command output

Field	Description
LSP	Number of LSP tunnels.
GRE	This field is not supported in the current software version. Number of GRE tunnels.
CRLSP	This field is not supported in the current software version. Number of CRLSP tunnels.
SRLSP	This field is not supported in the current software version. Number of SRLSP tunnels.

‌

display tunnel-policy

Use display tunnel-policy to display tunnel policy information.

Syntax

display tunnel-policy [ tunnel-policy-name ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

tunnel-policy-name: Specifies a tunnel policy by its name, a case-sensitive string of 1 to 19 characters. If you do not specify a tunnel policy, this command displays information about all tunnel policies.

Examples

# Display information about all tunnel policies.

<Sysname> display tunnel-policy

Tunnel policy name   : policy1

Preferred paths      :

  Interface  : not configured

  Tunnel type: not configured

Select-Seq           : LSP

Load balance number  : 8

Strict               : no

# Display information about tunnel policy policy1.

<Sysname> display tunnel-policy policy1

Tunnel policy name  : policy1

Preferred paths     :

  Interface  : not configured

  Tunnel type: not configured

Select-Seq          : LSP

Load balance number : 1

Strict              : no

Table 3 Command output

Field	Description
Preferred paths	Preferred tunnels information.
Interface	Tunnel interface name of the preferred tunnel.
Tunnel type	This field is not supported in the current software version. Type of the preferred tunnel: TE.
Select-Seq	Tunnel selection order. The tunnel types are displayed in descending order of priority in tunnel selection.
Load balance number	Number of tunnels for load balancing.
Strict	Whether the strict method is used to select tunnels for load balancing: ·     no—The tunnel policy can use a hybrid of the specified types of tunnels for load balancing. ·     yes—The tunnel policy uses only one type of tunnels for load balancing.

‌

select-seq load-balance-number

Use select-seq load-balance-number to configure the tunnel selection order and set the number of tunnels for load balancing.

Use undo select-seq to restore the default.

Syntax

select-seq [ strict ] lsp load-balance-number number

undo select-seq

Default

The device selects only one tunnel.

Views

Tunnel policy view

Predefined user roles

network-admin

Parameters

strict: Uses the same type of tunnels for load balancing. If you do not specify this keyword, the device can use a hybrid of the specified types of tunnels for load balancing.

lsp: Uses LSP tunnels.

load-balance-number number: Specifies the number of tunnels for load balancing, in the range of 1 to 16.

Examples

# Configure tunnel policy policy1 to use only LSP tunnels, and set the load balancing number to 2.

<Sysname> system-view

[Sysname] tunnel-policy policy1

[Sysname-tunnel-policy-policy1] select-seq lsp load-balance-number 2

Related commands

preferred-path

tunnel-policy (system view)

Use tunnel-policy to create a tunnel policy and enter its view, or enter the view of an existing tunnel policy.

Use undo tunnel-policy to delete a tunnel policy.

Syntax

tunnel-policy tunnel-policy-name

undo tunnel-policy tunnel-policy-name

Default

No tunnel policies exist.

Views

System view

Predefined user roles

network-admin

Parameters

tunnel-policy-name: Specifies a name for the tunnel policy, a case-sensitive string of 1 to 19 characters.

Examples

# Create tunnel policy policy1 and enter its view.

<Sysname> system-view

[Sysname] tunnel-policy policy1

[Sysname-tunnel-policy-policy1]