Contents

Configuring PBR·· 1

About PBR· 1

Packet forwarding process· 1

PBR types· 1

Policy· 1

Restrictions and guidelines: PBR configuration· 2

PBR tasks at a glance· 2

Configuring a policy· 3

Creating a node· 3

Setting match criteria for a node· 3

Configuring actions for a node· 3

Specifying a policy for PBR· 5

Specifying a policy for local PBR· 5

Specifying a policy for interface PBR· 5

Display and maintenance commands for PBR· 5

PBR configuration examples· 6

Example: Configuring packet type-based local PBR· 6

Example: Configuring packet type-based interface PBR· 7

 

Configuring PBR

About PBR

Policy-based routing (PBR) uses user-defined policies to route packets. A policy can specify parameters for packets that match specific criteria such as ACLs. The parameters include the next hop and default next hop.

Packet forwarding process

Upon receiving a packet, the device forwards the packet as follows:

1.     Uses the configured PBR policy to forward that packet.

2.     Searches the routing table for a route (except the default route) to forward the packet if one of the following conditions exists:

¡     No matching policy node is found.

¡     A matching policy node is found, but packet forwarding failed.

3.     Uses the default next hops specified in the PBR policy to forward the packet if the route-based forwarding failed.

4.     Uses the default route to forward the packet if the forwarding based on the default next hops failed.

PBR types

PBR includes the following types:

·     Local PBR—Guides the forwarding of locally generated packets, such as ICMP packets generated by using the ping command.

·     Interface PBR—Guides the forwarding of packets received on an interface.

Policy

A policy includes match criteria and actions to be taken on the matching packets. A policy can have one or multiple nodes as follows:

·     Each node is identified by a node number. A smaller node number has a higher priority.

·     A node contains if-match and apply clauses. An if-match clause specifies a match criterion, and an apply clause specifies an action.

·     A node has a match mode of permit or deny.

A policy compares packets with nodes in priority order. If a packet matches the criteria on a node, it is processed by the action on the node. If the packet does not match any criteria on the node, it goes to the next node for a match. If the packet does not match the criteria on any node, the device performs a routing table lookup.

Relationship between if-match clauses

On a node, you can specify multiple types of if-match clauses, but only one if-match clause for each type.

To match a node, a packet must match all types of the if-match clauses for the node but only one if-match clause for each type.

Relationship between apply clauses

You can specify multiple apply clauses for a node, but some of them might not be executed. For more information about relationship between apply clauses, see "Configuring actions for a node."

Relationship between the match mode and clauses on the node

Does a packet match all the if-match clauses on the node?	Match mode
	Permit	Deny
Yes.	·     If the node contains apply clauses, PBR executes the apply clauses on the node. ¡     If PBR-based forwarding succeeds, PBR does not compare the packet with the next node. ¡     If PBR-based forwarding fails, PBR does not compare the packet with the next node. ·     If the node does not contain apply clauses, the device performs a routing table lookup for the packet.	The device performs a routing table lookup for the packet.
No.	PBR compares the packet with the next node.	PBR compares the packet with the next node.

‌

NOTE: A node that has no if-match clauses matches any packet.

‌

Restrictions and guidelines: PBR configuration

If the device performs forwarding in software, PBR does not process IP packets destined for the local device.

If the device performs forwarding in hardware and a packet destined for it matches a PBR policy, PBR will execute the apply clauses in the policy, including the clause for forwarding. When you configure a PBR policy, be careful to avoid this situation.

PBR tasks at a glance

To configure PBR, perform the following tasks:

1.     Configuring a policy

a.     Creating a node

b.     Setting match criteria for a node

c.     Configuring actions for a node

2.     Specifying a policy for PBR

Choose the following tasks as needed:

¡     Specifying a policy for local PBR

¡     Specifying a policy for interface PBR

Configuring a policy

Creating a node

1.     Enter system view.

system-view

2.     Create a node for a policy, and enter its view.

policy-based-route policy-name [ deny | permit ] node node-number

3.     (Optional.) Configure a description for the policy node.

description text

By default, no description is configured for a policy node.

Setting match criteria for a node

1.     Enter system view.

system-view

2.     Enter policy node view.

policy-based-route policy-name [ deny | permit ] node node-number

3.     Set match criteria.

¡     Set an ACL match criterion.

if-match acl { acl-number | name acl-name }

By default, no ACL match criterion is set.

The ACL match criterion cannot match Layer 2 information.

When using the ACL to match packets, PBR ignores the action (permit or deny) in the ACL.

Configuring actions for a node

About this task

The apply clauses allow you to specify the actions to be taken on matching packets on a node.

The following apply clauses determine the packet forwarding paths in a descending order:

·     apply next-hop

·     apply output-interface

·     apply default-next-hop

PBR supports the apply clauses in Table 1.

Table 1 Apply clauses supported in PBR

Clause	Meaning	Remarks
apply precedence	Sets an IP precedence.	This clause is always executed.
apply next-hop and apply output-interface	Sets next hops and sets output interfaces.	If both clauses are configured, only the apply next-hop clause is executed.
apply default-next-hop	Sets default next hops.	The clause takes effect only in the following cases: ·     No next hops are set or the next hops are invalid. ·     The packet does not match any route in the routing table.

‌

Restrictions and guidelines

If you specify a next hop or default next hop, PBR periodically performs FIB table lookup to determine its availability. Temporary service interruption might occur if PBR does not update the route immediately after its availability status changes.

Configuring actions to modify packet fields

1.     Enter system view.

system-view

2.     Enter policy node view.

policy-based-route policy-name [ deny | permit ] node node-number

3.     Set an IP precedence.

apply precedence { type | value }

By default, no IP precedence is specified.

Configuring actions to direct packet forwarding

1.     Enter system view.

system-view

2.     Enter policy node view.

policy-based-route policy-name [ deny | permit ] node node-number

3.     Configure actions.

¡     Set next hops.

apply next-hop [ vpn-instance vpn-instance-name ] { ip-address [ direct ] }&<1-2>

By default, no next hops are specified.

On a node, you can specify a maximum of two next hops for backup in one command line or by executing this command multiple times.

If multiple next hops on the same subnet are specified for backup, the device first uses the subnet route for the next hops to forward packets when the primary next hop fails. If the subnet route is not available, the device selects a backup next hop.

¡     Set output interfaces.

apply output-interface null 0

By default, no output interfaces are specified.

¡     Set default next hops.

apply default-next-hop [ vpn-instance vpn-instance-name ] { ip-address [ direct ] }&<1-2>

By default, no default next hops are specified.

On a node, you can specify a maximum of two default next hops for backup in one command line or by executing this command multiple times.

If multiple next hops on the same subnet are specified for backup, the device first uses the subnet route for the next hops to forward packets when the primary next hop fails. If the subnet route is not available, the device selects a backup next hop.

Specifying a policy for PBR

Specifying a policy for local PBR

About this task

Perform this task to specify a policy for local PBR to guide the forwarding of locally generated packets.

Restrictions and guidelines

You can specify only one policy for local PBR and must make sure the specified policy already exists. Before you apply a new policy, you must first remove the current policy.

Local PBR might affect local services such as ping and Telnet. When you use local PBR, make sure you fully understand its impact on local services of the device.

Procedure

1.     Enter system view.

system-view

2.     Specify a policy for local PBR.

ip local policy-based-route policy-name

By default, local PBR is not enabled.

Specifying a policy for interface PBR

About this task

Perform this task to apply a policy to an interface to guide the forwarding of packets received on the interface.

Restrictions and guidelines

You can apply only one policy to an interface and must make sure the specified policy already exists. Before you can apply a new interface PBR policy to an interface, you must first remove the current policy from the interface.

You can apply a policy to multiple interfaces.

Procedure

1.     Enter system view.

system-view

2.     Enter interface view.

interface interface-type interface-number

3.     Specify a policy for interface PBR.

ip policy-based-route policy-name

By default, no interface policy is applied to an interface.

Display and maintenance commands for PBR

Execute display commands in any view and reset commands in user view.

 

Task	Command
Display PBR policy information.	display ip policy-based-route [ policy policy-name ]
Display interface PBR configuration and statistics.	display ip policy-based-route interface interface-type interface-number [ slot slot-number ]
Display local PBR configuration and statistics.	display ip policy-based-route local [ slot slot-number ]
Display PBR configuration.	display ip policy-based-route setup
Clear PBR statistics.	reset ip policy-based-route statistics [ policy policy-name ]

‌

PBR configuration examples

Example: Configuring packet type-based local PBR

Network configuration

As shown in Figure 1, Switch B and Switch C do not have a route to reach each other.

Configure PBR on Switch A to forward all TCP packets to the next hop 1.1.2.2 (Switch B).

Figure 1 Network diagram

‌

Procedure

1.     Configure Switch A:

# Create VLAN 10 and VLAN 20.

<SwitchA> system-view

[SwitchA] vlan 10

[SwitchA-vlan10] quit

[SwitchA] vlan 20

[SwitchA-vlan20] quit

# Configure the IP addresses of VLAN-interface 10 and VLAN-interface 20.

[SwitchA] interface vlan-interface 10

[SwitchA-Vlan-interface10] ip address 1.1.2.1 24

[SwitchA-Vlan-interface10] quit

[SwitchA] interface vlan-interface 20

[SwitchA-Vlan-interface20] ip address 1.1.3.1 24

[SwitchA-Vlan-interface20] quit

# Configure ACL 3101 to match TCP packets.

[SwitchA] acl advanced 3101

[SwitchA-acl-ipv4-adv-3101] rule permit tcp

[SwitchA-acl-ipv4-adv-3101] quit

# Configure Node 5 for the policy aaa to forward TCP packets to next hop 1.1.2.2.

[SwitchA] policy-based-route aaa permit node 5

[SwitchA-pbr-aaa-5] if-match acl 3101

[SwitchA-pbr-aaa-5] apply next-hop 1.1.2.2

[SwitchA-pbr-aaa-5] quit

# Configure local PBR by applying the policy aaa to Switch A.

[SwitchA] ip local policy-based-route aaa

2.     Configure Switch B:

# Create VLAN 10.

<SwitchB> system-view

[SwitchB] vlan 10

[SwitchB-vlan10] quit

# Configure the IP address of VLAN-interface 10.

[SwitchB] interface vlan-interface 10

[SwitchB-Vlan-interface10] ip address 1.1.2.2 24

3.     Configure Switch C:

# Create VLAN 20.

<SwitchC> system-view

[SwitchC] vlan 20

[SwitchC-vlan20] quit

# Configure the IP address of VLAN-interface 20.

[SwitchC] interface vlan-interface 20

[SwitchC-Vlan-interface20] ip address 1.1.3.2 24

Verifying the configuration

1.     Perform telnet operations to verify that local PBR on Switch A operates as configured to forward the matching TCP packets to the next hop 1.1.2.2 (Switch B), as follows:

# Verify that you can telnet to Switch B from Switch A successfully. (Details not shown.)

# Verify that you cannot telnet to Switch C from Switch A. (Details not shown.)

2.     Verify that Switch A forwards packets other than TCP packets through VLAN-interface 20. For example, verify that you can ping Switch C from Switch A. (Details not shown.)

Example: Configuring packet type-based interface PBR

Network configuration

As shown in Figure 2, Switch B and Switch C do not have a route to reach each other.

Configure PBR on Switch A to forward all TCP packets received on VLAN-interface 11 to the next hop 1.1.2.2 (Switch B).

Figure 2 Network diagram

‌

Procedure

1.     Configure unicast routing protocol settings to make sure Switch B and Switch C can reach Host A. (Details not shown.)

2.     Configure Switch A:

# Create VLAN 10 and VLAN 20.

<SwitchA> system-view

[SwitchA] vlan 10

[SwitchA-vlan10] quit

[SwitchA] vlan 20

[SwitchA-vlan20] quit

# Configure the IP addresses of VLAN-interface 10 and VLAN-interface 20.

[SwitchA] interface vlan-interface 10

[SwitchA-Vlan-interface10] ip address 1.1.2.1 24

[SwitchA-Vlan-interface10] quit

[SwitchA] interface vlan-interface 20

[SwitchA-Vlan-interface20] ip address 1.1.3.1 24

[SwitchA-Vlan-interface20] quit

# Configure ACL 3101 to match TCP packets.

[SwitchA] acl advanced 3101

[SwitchA-acl-ipv4-adv-3101] rule permit tcp

[SwitchA-acl-ipv4-adv-3101] quit

# Configure Node 5 for the policy aaa to forward TCP packets to next hop 1.1.2.2.

[SwitchA] policy-based-route aaa permit node 5

[SwitchA-pbr-aaa-5] if-match acl 3101

[SwitchA-pbr-aaa-5] apply next-hop 1.1.2.2

[SwitchA-pbr-aaa-5] quit

# Configure interface PBR by applying the policy aaa to VLAN-interface 11.

[SwitchA] interface vlan-interface 11

[SwitchA-Vlan-interface11] ip address 10.110.0.10 24

[SwitchA-Vlan-interface11] ip policy-based-route aaa

[SwitchA-Vlan-interface11] quit

Verifying the configuration

1.     Perform telnet operations to verify that interface PBR on Switch A operates as configured to forward the matching TCP packets to the next hop 1.1.2.2 (Switch B), as follows:

# Verify that you can telnet to Switch B from Host A successfully. (Details not shown.)

# Verify that you cannot telnet to Switch C from Host A. (Details not shown.)

2.     Verify that Switch A forwards packets other than TCP packets through VLAN-interface 20. For example, verify that you can ping Switch C from Host A. (Details not shown.)