Contents

Configuring flow log· 1

About flow log· 1

Flow log export 1

Flow log versions· 1

Flow log tasks at a glance· 3

Prerequisites for flow log· 3

Specifying a flow log export destination· 3

Restrictions and guidelines for flow log export destination configuration· 3

Specifying a log host as the flow log export destination· 3

Specifying the information center as the flow log export destination· 4

Configuring the flow log version· 4

Specifying a source IP address for flow log packets· 4

Configuring the timestamp of flow log entries· 5

Enabling load balancing for flow log entries· 5

Verifying and maintaining flow log· 5

Displaying flow log configuration and statistics· 5

Clearing flow log statistics· 6

Flow log configuration examples· 6

Example: Configuring flow log export 6

 

Configuring flow log

About flow log

Flow log records users' access to external networks based on flows. Each flow is identified by a 5-tuple of the source IP address, destination IP address, source port, destination port, and protocol number.

Flow log creates entries based on NAT sessions.

Flow log export

You can export flow log entries in the following methods:

·     Export flow log entries to log hosts. Flow log entries are sent as binary characters in UDP. One UDP packet can contain multiple log entries.

·     Export flow log entries to the information center. Flow log entries are converted to syslog entries in ASCII format, with the informational severity level. The information center specifies the output destinations for the logs. Available output destinations include the console, log host, and log file. For more information about the information center, see "Configuring the information center."

Log entries in ASCII format are human readable. However, the log data volume is higher in ASCII format than in binary format.

Flow log versions

Flow log has two versions: version 1.0 and version 3.0. Table 1 and Table 2 show the fields available in the versions.

Table 1 Flow log 1.0 fields

Field	Description
SrcIP	Source IP address before NAT.
DestIP	Destination IP address before NAT.
SrcPort	Source TCP/UDP port number before NAT.
DestPort	Destination TCP/UDP port number before NAT.
StartTime	Start time of the flow, in seconds.
EndTime	End time of the flow, in seconds. This field is 0 if the Operator field is 6 (regular connectivity check record for the active flow).
Protocol	Protocol number.
Operator	Reasons why a flow log entry was generated: ·     0—Reserved. ·     1—Flow was ended normally. ·     2—Flow was aged out because of aging timer expiration. ·     3—Flow was aged out because of configuration change or manual deletion. ·     4—Flow was aged out because of insufficient resources. ·     5—Reserved. ·     6—Regular connectivity check record for the active flow. ·     7—Flow was deleted because a new flow was created when the flow table was full. ·     8—Flow was created. ·     FE—Other reasons. ·     10-FE-1—Reserved for future use.
Reserved	Reserved for future use.

‌

Table 2 Flow log 3.0 fields

Field	Description
Protocol	Protocol number.
Operator	Reasons why a flow log was generated: ·     0—Reserved. ·     1—Flow was ended normally. ·     2—Flow was aged out because of aging timer expiration. ·     3—Flow was aged out because of configuration change. ·     4—Flow was aged out because of insufficient resources. ·     5—Reserved. ·     6—Regular connectivity check record for the active flow. ·     7—Flow was deleted because a new flow was created when the flow table was full. ·     8—Flow was created. ·     FE—Other reasons. ·     10-FE-1—Reserved for future use.
IPVersion	IP packet version.
TosIPv4	ToS field of the IPv4 packet.
SourceIP	Source IP address before NAT.
SrcNatIP	Source IP address after NAT.
DestIP	Destination IP address before NAT.
DestNatIP	Destination IP address after NAT.
SrcPort	Source TCP/UDP port number before NAT.
SrcNatPort	Source TCP/UDP port number after NAT.
DestPort	Destination TCP/UDP port number before NAT.
DestNatPort	Destination TCP/UDP port number after NAT.
StartTime	Start time of the flow, in seconds.
EndTime	End time of the flow, in seconds. This field is 0 when the Operator field is 6 (regular connectivity check record for the active flow).
InTotalPkg	Number of packets received for the session.
InTotalByte	Number of bytes received for the session.
OutTotalPkg	Number of packets sent for the session.
OutTotalByte	Number of bytes sent for the session.
InVPNID	ID of the source VPN instance.
OutVPNID	ID of the destination VPN instance.
Reserved1	Reserved field.
AppID	Application protocol ID.
Reserved3	Reserved field.

‌

Flow log tasks at a glance

To configure flow log, perform the following tasks:

1.     Specifying a flow log export destination

Choose one of the following tasks:

¡     Specifying a log host as the flow log export destination

¡     Specifying the information center as the flow log export destination

2.     (Optional.) Configuring the flow log version

3.     (Optional.) Specifying a source IP address for flow log packets

4.     (Optional.) Configuring the timestamp of flow log entries

5.     (Optional.) Enabling load balancing for flow log entries

Prerequisites for flow log

Before you configure the flow log feature, complete the following tasks:

·     Enable NAT logging by using the nat log enable command.

·     Enable the following NAT logging features as needed:

¡     Logging of active NAT flows.

¡     Logging of NAT session establishment events.

¡     Logging of NAT session removal events.

For more information about the NAT logging commands, see NAT Command Reference.

Specifying a flow log export destination

Restrictions and guidelines for flow log export destination configuration

You can export flow log entries to a log host or the information center, but not both. If you configure both methods, the system exports flow log entries to the information center.

Flow log entries exported to the information center has the informational severity level.

Specifying a log host as the flow log export destination

1.     Enter system view.

system-view

2.     Specify a log host as the destination for flow log export.

userlog flow export [ vpn-instance vpn-instance-name ] host { hostname | ipv4-address | ipv6 ipv6-address } port udp-port

By default, no log hosts are specified.

You can specify multiple log hosts.

Specifying the information center as the flow log export destination

1.     Enter system view.

system-view

2.     Specify the information center as the destination for flow log export.

userlog flow syslog

By default, flow log entries are not exported to the information center.

Configuring the flow log version

Restrictions and guidelines

Make sure the specified flow log version is supported on the log host.

If you configure the flow log version multiple times, the most recent configuration takes effect.

Procedure

1.     Enter system view.

system-view

2.     Configure the flow log version.

userlog flow export version version-number

The default flow log version is 1.0.

Specifying a source IP address for flow log packets

About this task

By default, the source IP address for flow log packets is the IP address of their outgoing interface. For the log hosts to filter log entries by log sender, specify a source IP address for all flow log packets.

Restrictions and guidelines

As a best practice, use a Loopback interface's address as the source IP address for flow log packets. A Loopback interface is always up. The setting avoids export failure on interfaces that might go down.

Procedure

1.     Enter system view.

system-view

2.     Specify a source IP address for flow log packets.

userlog flow export source-ip { ipv4-address | ipv6 ipv6-address }

By default, the source IP address for flow log packets is the IP address of their outgoing interface.

Configuring the timestamp of flow log entries

About this task

The device uses either the local time or the UTC time in the timestamp of flow logs.

·     UTC time—Standard Greenwich Mean Time (GMT).

·     Local time—Standard GMT plus or minus the time zone offset.

The time zone offset can be configured by using the clock timezone command. For more information, see basic device management commands in System Management Command Reference.

Procedure

1.     Enter system view.

system-view

2.     Configure the device to use the local time in the flow log timestamp.

userlog flow export timestamp localtime

By default, the UTC time is used in the flow log timestamp.

Enabling load balancing for flow log entries

About this task

By default, the device sends a copy of each flow log entry to all configured log hosts. When one log host fails, other log hosts still have complete flow log entries.

In load balancing mode, flow log entries are distributed among log hosts based on the source IP addresses (before NAT) that are recorded in the entries. The flow log entries generated for the same source IP address are sent to the same log host.

Restrictions and guidelines

In load balancing mode, flow logs are load balanced among all configured log hosts, regardless of whether the log hosts are reachable. If a log host is unreachable, the flow logs sent to it will be lost.

Procedure

1.     Enter system view.

system-view

2.     Enable load balancing for flow log entries.

userlog flow export load-balancing

By default, load balancing is disabled.

Verifying and maintaining flow log

Displaying flow log configuration and statistics

To display flow log configuration and statistics, execute the following command in any view:

display userlog export

Clearing flow log statistics

To clear flow log statistics, execute the following command in user view:

reset userlog flow export

Flow log configuration examples

Example: Configuring flow log export

Network configuration

As shown in Figure 1, configure flow log on the device to send flow log entries generated for the user to the log host.

Figure 1 Network diagram

‌

Procedure

# Configure IP addresses, as shown in Figure 1. Make sure the device, user, and the log host can reach one another. (Details not shown.)

# Enable NAT logging.

<Device> system-view

[Device] nat log enable

# Enable NAT logging for session establishment events, session removal events, and active flows.

[Device] nat log flow-begin

[Device] nat log flow-end

[Device] nat log flow-active 10

# Set the flow log version to 3.0.

[Device] userlog flow export version 3

# Specify the log host at 1.2.3.6 as the destination for flow log export. Set the UDP port number to 2000.

[Device] userlog flow export host 1.2.3.6 port 2000

# Specify 2.2.2.2 as the source IP address for flow log packets.

[Device] userlog flow export source-ip 2.2.2.2

[Device] quit

Verifying the configuration

# Display the flow log configuration and statistics.

<Device> display userlog export

Flow:

  Export flow log as UDP Packet.

  Version: 3.0

  Source ipv4 address: 2.2.2.2

  Log load balance function: Disabled

  Local time stamp: Disabled

  Number of log hosts: 1

 

  Log host 1:

    Host/Port: 1.2.3.6/2000

    Total logs/UDP packets exported: 112/87