Contents

Port mirroring commands· 1

display mirroring-group· 1

mirroring-group· 2

mirroring-group mirroring-port (interface view) 2

mirroring-group mirroring-port (system view) 3

mirroring-group monitor-port (interface view) 4

mirroring-group monitor-port (system view) 4

Flow mirroring commands· 6

mirror-to interface· 6

 

Port mirroring commands

display mirroring-group

Use display mirroring-group to display mirroring group information.

Syntax

display mirroring-group { group-id | all | local }

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

group-id: Specifies a mirroring group by its ID. The value range for this argument is 1 to 6.  

all: Specifies all mirroring groups.

local: Specifies local mirroring groups.

Usage guidelines

Mirroring group information includes the type, status, and content of a mirroring group. It is sorted by mirroring group number.

Examples

# Display information about all mirroring groups.

<Sysname> display mirroring-group all

Mirroring group 1:

    Type: Local

    Status: Active

    Mirroring port: Ten-GigabitEthernet0/0/6 Inbound

    Monitor port: Ten-GigabitEthernet0/0/7

Table 1 Command output

Field	Description
Mirroring group	Number of the mirroring group.
Type	Type of the mirroring group: Local.
Status	Status of the mirroring group: ·     Active—The mirroring group has taken effect. ·     Incomplete—The mirroring group configuration is not complete and does not take effect.
Mirroring port	Source port.
Monitor port	Destination port.

 

mirroring-group

Use mirroring-group to create a mirroring group.

Use undo mirroring-group to delete mirroring groups.

Syntax

mirroring-group group-id local

undo mirroring-group { group-id | all | local }

Default

No mirroring groups exist.

Views

System view

Predefined user roles

network-admin

Parameters

group-id: Specifies a mirroring group ID. The value range for this argument is 1 to 6.  

local: Specifies local mirroring groups.

all: Specifies all mirroring groups.

Examples

# Create local mirroring group 1.

<Sysname> system-view

[Sysname] mirroring-group 1 local

mirroring-group mirroring-port (interface view)

Use mirroring-group mirroring-port to configure a port as a source port for a mirroring group.

Use undo mirroring-group mirroring-port to restore the default.

Syntax

mirroring-group group-id mirroring-port { both | inbound | outbound }

undo mirroring-group group-id mirroring-port

Default

A port does not act as a source port for any mirroring groups.

Views

Interface view

Predefined user roles

network-admin

Parameters

group-id: Specifies a mirroring group by its ID. The value range for this argument is 1 to 6.  

both: Mirrors both received and sent packets.

inbound: Mirrors only received packets.

outbound: Mirrors only sent packets.

Usage guidelines

A port can act as a source port for only one mirroring group.

A source port cannot be used as a monitor port.

Examples

# Create local mirroring group 1 to monitor the bidirectional traffic of the port Ten-GigabitEthernet 0/0/6.

<Sysname> system-view

[Sysname] mirroring-group 1 local

[Sysname] interface ten-gigabitethernet 0/0/6

[Sysname-Ten-GigabitEthernet0/0/6] mirroring-group 1 mirroring-port both

Related commands

mirroring-group

mirroring-group mirroring-port (system view)

Use mirroring-group mirroring-port to configure source ports for a mirroring group.

Use undo mirroring-group mirroring-port to remove source ports from a mirroring group.

Syntax

mirroring-group group-id mirroring-port interface-list { both | inbound | outbound }

undo mirroring-group group-id mirroring-port interface-list

Default

No source port is configured for a mirroring group.

Views

System view

Predefined user roles

network-admin

Parameters

group-id: Specifies a mirroring group by its ID. The value range for this argument is 1 to 6.  

interface-list: Specifies a space-separated list of up to eight interface items. Each item specifies an interface by its type and number or specifies a range of interfaces in the form of interface-type interface-number1 to interface-type interface-number2. When you specify a range of interfaces, the interfaces must be of the same type and on the same slot. The start interface number must be identical to or lower than the end interface number.

both: Mirrors both received and sent packets.

inbound: Mirrors only received packets.

outbound: Mirrors only sent packets.

Usage guidelines

A port can act as a source port for only one mirroring group.

A source port cannot be used as a monitor port.

Examples

# Create local mirroring group 1 to monitor the bidirectional traffic of Ten-GigabitEthernet 0/0/6.

<Sysname> system-view

[Sysname] mirroring-group 1 local

[Sysname] mirroring-group 1 mirroring-port ten-gigabitethernet 0/0/6 both

Related commands

mirroring-group

mirroring-group monitor-port (interface view)

Use mirroring-group monitor-port to configure a port as the monitor port for a mirroring group.

Use undo mirroring-group monitor-port to restore the default.

Syntax

mirroring-group group-id monitor-port

undo mirroring-group group-id monitor-port

Default

A port does not act as the monitor port for any mirroring groups.

Views

Interface view

Predefined user roles

network-admin

Parameters

group-id: Specifies a mirroring group by its ID. The value range for this argument is 1 to 6.  

Usage guidelines

Do not enable the spanning tree feature on the monitor port of a mirroring group.

Use a monitor port only for port mirroring, so the data monitoring device receives and analyzes only the mirrored traffic.

The member port of an existing mirroring group cannot be configured as a monitor port.

Examples

# Create local mirroring group 1 and configure Ten-GigabitEthernet 0/0/6 as its monitor port.

<Sysname> system-view

[Sysname] mirroring-group 1 local

[Sysname] interface ten-gigabitethernet 0/0/6

[Sysname-Ten-GigabitEthernet0/0/6] mirroring-group 1 monitor-port

Related commands

mirroring-group

mirroring-group monitor-port (system view)

Use mirroring-group monitor-port to configure the monitor ports for a mirroring group.

Use undo mirroring-group monitor-port to remove the monitor ports from a mirroring group.

Syntax

mirroring-group group-id monitor-port interface-type interface-number

undo mirroring-group group-id monitor-port interface-type interface-number

Default

No monitor port is configured for a mirroring group.

Views

System view

Predefined user roles

network-admin

Parameters

group-id: Specifies a mirroring group by its ID. The value range for this argument is 1 to 6.  

interface-type interface-number: Specifies an interface by its type and number.

Usage guidelines

Do not enable the spanning tree feature on the monitor port of a mirroring group.

Use a monitor port only for port mirroring, so the data monitoring device receives only the mirrored traffic.

The member port of an existing mirroring group cannot be configured as a monitor port.

Examples

# Create local mirroring group 1 and configure Ten-GigabitEthernet 0/0/6 as its monitor port.

<Sysname> system-view

[Sysname] mirroring-group 1 local

[Sysname] mirroring-group 1 monitor-port ten-gigabitethernet 0/0/6

Related commands

mirroring-group

Flow mirroring commands

mirror-to interface

Use mirror-to interface to configure a mirroring action that mirrors traffic to an interface.

Use undo mirror-to interface to delete a mirroring action that mirrors traffic to an interface.

Syntax

mirror-to interface interface-type interface-number

undo mirror-to interface interface-type interface-number

Default

No mirroring actions exist to mirror traffic to interfaces.

Views

Traffic behavior view

Predefined user roles

network-admin

Parameters

interface-type interface-number: Specifies an interface by its type and number.

Usage guidelines

You can execute this command multiple times for a traffic behavior to mirror traffic to different interfaces.

Examples

# Create traffic behavior 1 and configure the action of mirroring traffic to Ten-GigabitEthernet 0/0/6 for the traffic behavior.

<Sysname> system-view

[Sysname] traffic behavior 1

[Sysname-behavior-1] mirror-to interface ten-gigabitethernet 0/0/6