After the remote PEs are discovered through BGP, you can use the signaling-protocol command to specify the signaling protocol (LDP or BGP) to establish PWs to the discovered remote PEs.

Examples

# Enable VSI aaa to automatically discover neighbors through BGP and enter auto-discovery VSI view.

<Sysname> system-view

[Sysname] vsi aaa

[Sysname-vsi-aaa] auto-discovery bgp

[Sysname-vsi-aaa-auto]

Related commands

display l2vpn pw

display l2vpn vsi

backup-peer

Use back-peer in VSI LDP PW view to configure a VSI LDP backup PW and enter its view, or enter the view of an existing VSI LDP backup PW.

Use back-peer in VSI static PW view to configure a VSI static backup PW and enter its view, or enter the view of an existing VSI static backup PW.

Use undo backup-peer to restore the default.

Syntax

In VSI LDP PW view:

backup-peer ip-address [ pw-id pw-id ] [ pw-class class-name | tunnel-policy tunnel-policy-name ] *

undo backup-peer ip-address pw-id pw-id

In VSI static PW view:

backup-peer ip-address [ pw-id pw-id ] in-label label-value out-label label-value [ pw-class class-name | tunnel-policy tunnel-policy-name ] *

undo backup-peer ip-address pw-id pw-id

Default

No backup PWs exist for VPLS.

Views

VSI LDP PW view

VSI static PW view

Predefined user roles

network-admin

Parameters

ip-address: Specifies the LSR ID of the peer PE on the backup PW.

pw-id pw-id: Specifies a PW ID for the backup PW, in the range of 1 to 4294967295.

in-label label-value: Specifies the incoming label for the backup PW. The value range for the label-value argument is 16 to 2047.

out-label label-value: Specifies the outgoing label for the backup PW, in the range of 16 to 1048575.

pw-class class-name: Specifies a PW class by its name, a case-sensitive string of 1 to 19 characters. You can specify a PW class to configure the PW data encapsulation type and control word for the backup PW. If you do not specify a PW class, the PW data encapsulation type of the backup PW is VLAN and the backup PW does not support control word.

tunnel-policy tunnel-policy-name: Specifies a tunnel policy by its name, a case-insensitive string of 1 to 19 characters. If you do not specify a tunnel policy, the backup PW uses the default tunnel policy.

Usage guidelines

This command configures a backup PW for a PW to implement PW redundancy. The backup PW is used when the primary PW fails.

You must assign the backup PW a different peer LSR ID and PW ID than any existing VPLS PWs or cross-connect PWs.

If both the default PW ID in the default-pw-id command and a PW ID in the backup-peer command are configured, the PW ID in the backup-peer command is used. If only the default PW ID is configured, the default PW ID is used. If no default PW ID is configured, you must provide a PW ID in the backup-peer command.

A static PW must have a different incoming label than an existing static LSP or static CRLSP. If they are the same, the static PW is not available, even if you change the incoming label of the static LSP or the static CRLSP. To make the static PW available, delete the static PW, and reconfigure it with an unused incoming label.

Examples

# Configure a primary and a backup LDP PW for VSI vpn1, and specify the peer PE address and PW ID of the primary PW as 4.4.4.4 and 100, and those of the backup PW as 5.5.5.5 and 200.

<Sysname> system-view

[Sysname] vsi vpn1

[Sysname-vsi-vpn1] pwsignaling ldp

[Sysname-vsi-vpn1-ldp] peer 4.4.4.4 pw-id 100

[Sysname-vsi-vpn1-ldp-4.4.4.4-100] backup-peer 5.5.5.5 pw-id 200

[Sysname-vsi-vpn1-ldp-4.4.4.4-100-backup]

Related commands

default-pw-id

display l2vpn ldp

display l2vpn pw

peer

control-word enable

Use control-word enable to enable the control word feature.

Use undo control-word enable to disable the control word feature.

Syntax

control-word enable

undo control-word enable

Default

Control word is disabled.

Views

PW class view

Predefined user roles

network-admin

Usage guidelines

The control word field is between the MPLS label stack and the Layer 2 data. It carries extra control information about the Layer 2 frame, for example, the sequence number. The control word feature has the following functions:

· Avoids fragment disorder. In multipath forwarding, fragments received might be disordered. You can configure the control word feature on the device, so the device can reorder the fragments according to the sequence number carried in the control word field.

· Identifies the original payload length for packets that include padding.

Packets transmitted on a PW to carry the control word field only when control word is enabled on both PEs.

Examples

# Enable control word for PW class pw100.

<Sysname> system-view

[Sysname] pw-class pw100

[Sysname-pw-pw100] control-word enable

Related commands

display l2vpn pw-class

default-pw-id

Use default-pw-id to set the default PW ID for a VSI.

Use undo default-pw-id to restore the default.

Syntax

default-pw-id default-pw-id

undo default-pw-id

Default

No default PW ID is set for a VSI.

Views

VSI view

Predefined user roles

network-admin

Parameters

default-pw-id: Specifies the default PW ID for the VSI, in the range of 1 to 4294967295.

Usage guidelines

After you set the default PW ID for a VSI, you do not need to provide a PW ID in the backup-peer and peer commands.

Examples

# Set the default PW ID to 200 for VSI vpn1.

<Sysname> system-view

[Sysname] vsi vpn1

[Sysname-vsi-vpn1] default-pw-id 200

Related commands

backup-peer

peer

description

Use description to configure a description for a VSI.

Use undo description to restore the default.

Syntax

description text

undo description

Default

No description is configured for a VSI.

Views

VSI view

Predefined user roles

network-admin

Parameters

text: Specifies a description, a case-sensitive string of 1 to 80 characters.

Examples

# Configure a description of vsi for vpn1 for VSI vpn1.

<Sysname> system-view

[Sysname] vsi vpn1

[Sysname-vsi-vpn1] description vsi for vpn1

Related commands

display l2vpn vsi

display bgp l2vpn auto-discovery

Use display bgp l2vpn auto-discovery to display VPLS PE information discovered by BGP.

Syntax

display bgp [ instance instance-name ] l2vpn auto-discovery [ peer ip-address { advertised | received } [ statistics ] | route-distinguisher route-distinguisher [ pe-address ip-address [ advertise-info ] ] | statistics ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

instance instance-name: Displays VPLS PE information in a BGP instance. The instance-name argument specifies the BGP instance name, a case-sensitive string of 1 to 31 characters. If you do not specify a BGP instance, this command displays VPLS PE information in the default BGP instance.

peer ip-address: Displays VPLS PE information advertised to or received from a BGP peer specified by its IP address.

advertised: Displays VPLS PE information advertised to the BGP peer.

received: Displays VPLS PE information received from the BGP peer.

statistics: Displays BGP VPLS PE statistics.

route-distinguisher route-distinguisher: Displays BGP VPLS PE information for the route distinguisher (RD), which is a string of 3 to 21 characters. You can specify an RD in one of the following formats:

· 16-bit AS number:32-bit user-defined number. For example, 101:3.

· 32-bit IP address:16-bit user-defined number. For example, 192.168.122.15:1.

· 32-bit AS number:16-bit user-defined number, where the AS number must be equal to or greater than 65536. For example, 65536:1.

pe-address ip-address: Displays BGP VPLS PE information for a PE. The ip-address argument specifies the PE address.

advertise-info: Displays BGP VPLS PE advertisement information.

Usage guidelines

If you do not specify any parameters, this command displays brief information about all VPLS PEs discovered by BGP.

Examples

# Display brief information about all VPLS PEs discovered by BGP in the default BGP instance.

<Sysname> display bgp l2vpn auto-discovery

BGP local router ID is 192.168.1.140

Status codes: * - valid, > - best, d - dampened, h - history,

s - suppressed, S - stale, i - internal, e - external

Origin: i - IGP, e - EGP, ? - incomplete

Total number of automatically discovered PEs: 3

Route distinguisher: 2:2

Total number of automatically discovered PEs: 3

PE address Nexthop VPLS ID

* > 1.1.1.9 0.0.0.0 100:100

* >i 2.2.2.9 2.2.2.9 100:100

* >i 3.3.3.9 3.3.3.9 100:100

Table 1 Command output

Field	Description
Status codes	Status codes: · * – valid—Valid route. · > – best—Best route. · d – damped—Dampened route. · h – history—History route. · s – suppressed—Suppressed route. · S – Stale—Stale route. · i – internal—Internal route. · e – external—External route.
Origin	Origin of the label block: · i – IGP—Originated in the AS. · e – EGP—Learned through EGP. · ? – incomplete—Unknown origin.

Field

Description

Status codes

Status codes:

· * – valid—Valid route.

· > – best—Best route.

· d – damped—Dampened route.

· h – history—History route.

· s – suppressed—Suppressed route.

· S – Stale—Stale route.

· i – internal—Internal route.

· e – external—External route.

Origin

Origin of the label block:

· i – IGP—Originated in the AS.

· e – EGP—Learned through EGP.

· ? – incomplete—Unknown origin.

‌

# Display detailed information about the VPLS PE that has RD 2:2 and IP address 2.2.2.9 in the default BGP instance.

<Sysname> display bgp l2vpn auto-discovery route-distinguisher 2:2 pe-address 2.2.2.9

BGP local router ID: 192.168.1.140

Local AS number: 100

Route distinguisher: 2:2

Total number of automatically discovered PEs: 1

Paths: 1 available, 1 best

From : 2.2.2.9 (192.168.1.135)

Original nexthop: 2.2.2.9

Ext-Community : <RT: 2:2>, <VPLS ID: 100:100>

AS-path : (null)

Origin : igp

Attribute value : localpref 100, pref-val 0

PE address : 2.2.2.9

State : valid, internal, best

Table 2 Command output

Field	Description
Original nexthop	Original next hop. If the VPLS PE information was obtained from a BGP update, this field displays the next hop address in the received update.
Ext-Community	Extended community attribute: · RT—Route Target. · VPLS ID—VPLS instance identifier.
AS-path	AS path attribute, which records all ASs that the VPLS PE information passed to prevent routing loops.
Origin	Origin of the label block: · igp—Originated in the AS. · egp—Learned through EGP. · incomplete—Unknown origin.
Attribute value	Attribute of the VPLS PE information: · MED—Multi-Exit Discriminator attribute. · localpref—Local preference value. · pref-val—Preferred value. · pre—Preference value.
State	State of the VPLS PE information: · valid. · internal. · external. · local. · best.

‌

# Display BGP advertisement information for the specified VPLS PE in the default BGP instance.

<Sysname> display bgp l2vpn auto-discovery route-distinguisher 2:2 pe-address 1.1.1.9 advertise-info

BGP local router ID: 192.168.1.140

Local AS number: 100

Route distinguisher: 2:2

Total number of automatically discovered PEs: 1

Paths: 1 best

VPLS ID : 100:100

PE address : 1.1.1.9

Advertised to peers (2 in total):

2.2.2.9

3.3.3.9

display bgp l2vpn signaling

Use display bgp l2vpn signaling to display VPLS label block information maintained by BGP.

Syntax

display bgp [ instance instance-name ] l2vpn signaling [ peer ip-address { advertised | received } [ statistics ] | route-distinguisher route-distinguisher [ site-id site-id [ label-offset label-offset [ advertise-info ] ] ] | statistics ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

instance instance-name: Displays VPLS label block information in a BGP instance. The instance-name argument specifies the BGP instance name, a case-sensitive string of 1 to 31 characters. If you do not specify a BGP instance, this command displays VPLS label block information in the default BGP instance.

peer ip-address: Displays VPLS label block information advertised to or received from a BGP peer. The ip-address argument specifies the peer address.

advertised: Displays VPLS label block information advertised to the BGP peer.

received: Displays VPLS label block information received from the BGP peer.

statistics: Displays VPLS label block statistics.

route-distinguisher route-distinguisher: Displays BGP VPLS label block information for the route distinguisher (RD), which is a string of 3 to 21 characters. You can specify an RD in one of the following formats:

· 16-bit AS number:32-bit user-defined number. For example, 101:3.

· 32-bit IP address:16-bit user-defined number. For example, 192.168.122.15:1.

· 32-bit AS number:16-bit user-defined number, where the AS number must be equal to or greater than 65536. For example, 65536:1.

site-id site-id: Displays BGP VPLS label block information for a site. The site-id argument specifies the site ID.The site ID range is 0 to 65535.

label-offset label-offset: Displays information about the BGP VPLS label block with an offset. The label-offset argument specifies the offset in the range of 0 to 65535.

advertise-info: Displays BGP VPLS label block advertisement information.

Usage guidelines

If you do not specify any parameters, this command displays brief information about all BGP VPLS label blocks.

Examples

# Display brief information about all BGP VPLS label blocks in the default BGP instance.

<Sysname> display bgp l2vpn signaling

BGP local router ID is 192.168.1.135

Status codes: * - valid, > - best, d - dampened, h - history,

s - suppressed, S - stale, i - internal, e - external

Origin: i - IGP, e - EGP, ? - incomplete

Total number of label blocks: 2

Route distinguisher: 2:2

Total number of label blocks: 2

Site ID LB offset LB range LB base Nexthop

* > 1 0 10 1034 192.1.1.1

* >i 2 0 10 1162 192.3.3.3

Table 3 Command output

Field	Description
Status codes	Status codes: · * – valid—Valid route. · > – best—Best route. · d – damped—Dampened route. · h – history—History route. · s – suppressed—Suppressed route. · S – Stale—Stale route. · i – internal—Internal route. · e – external—External route.
Origin	Origin of the label block: · i – IGP—Originated in the AS. · e – EGP—Learned through EGP. · ? – incomplete—Unknown origin.
LB offset	Offset of the label block.
LB range	Size of the label block.
LB base	Initial value of the label block.

‌

# Display detailed information about the BGP VPLS label block that has RD 1:1, site ID 2, and offset 0 in the default BGP instance.

<Sysname> display bgp l2vpn signaling route-distinguisher 1:1 site-id 2 label-offset 0

BGP local router ID: 192.168.1.140

Local AS number: 100

Route distinguisher: 1:1

Total number of label blocks: 1

Paths: 1 available, 1 best

From : 2.2.2.9 (192.168.1.135)

Original nexthop: 2.2.2.9

Ext-Community : <RT: 1:1>, <L2VPN info: MTU 1500, Encap type BGP VPLS>

AS-path : (null)

Origin : igp

Attribute value : localpref 100, pref-val 0

Site ID : 2

LB offset : 0

LB base : 1418

LB range : 10

State : valid, internal, best

Table 4 Command output

Field	Description
Original nexthop	Original next hop. If the label block was obtained from a BGP route update, this field displays the next hop address in that BGP route update.
Ext-Community	Extended community attribute: · RT—Route target. · L2VPN info—L2VPN information, including the MTU and encapsulation type.
AS-path	AS path attribute, which records all ASs that the label block passed to prevent routing loops.
Origin	Origin of the label block: · igp—Originated in the AS. · egp—Learned through EGP. · incomplete—Unknown origin.
Attribute value	Attribute of the label block: · MED—Multi-Exit Discriminator attribute. · localpref—Local preference value. · pref-val—Preferred value. · pre—Preference value.
LB offset	Offset of the label block.
LB base	Initial value of the label block.
LB range	Size of the label block.
State	State of the label block: · valid. · internal. · external. · local. · best.

‌

# Display BGP advertisement information for the specified VPLS label block in the default BGP instance.

<Sysname> display bgp l2vpn signaling route-distinguisher 1:1 site-id 1 label-offset 0 advertise-info

BGP local router ID: 192.168.1.140

Local AS number: 100

Route distinguisher: 1:1

Total number of label blocks: 1

Paths: 1 best

Site ID : 1

LB offset : 0

LB base : 1418

LB range : 10

Advertised to peers (2 in total):

2.2.2.9

3.3.3.9

Table 5 Command output

Field	Description
LB offset	Offset of the label block.
LB base	Initial value of the label block.
LB range	Size of the label block.

‌

display l2vpn auto-discovery

Use display l2vpn auto-discovery to display information about automatically discovered VPLS PEs.

Syntax

display l2vpn auto-discovery [ peer ip-address ] [ vsi vsi-name ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

peer ip-address: Displays information about the specified VPLS PE. If you do not specify a PE, this command displays information about all automatically discovered VPLS PEs.

vsi vsi-name: Displays automatically discovered VPLS PEs for a VSI. The vsi-name argument specifies the VSI name, a case-sensitive string of 1 to 31 characters. If you do not specify a VSI, this command displays automatically discovered VPLS PEs for all VSIs.

Examples

# Display information about all automatically discovered VPLS PEs.

<Sysname> display l2vpn auto-discovery

Total number of automatically discovered peers: 2

VSI Name: bbb

RD PE_address VPLS ID Nexthop

2:2 1.1.1.9 100:100 1.1.1.9

2:2 3.3.3.9 100:100 3.3.3.9

Related commands

route-distinguisher

vpls-id

display l2vpn bgp

Use display l2vpn bgp to display VPLS label block information.

Syntax

display l2vpn bgp [ local | peer ip-address ] [ vsi vsi-name ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

local: Displays local VPLS label block information.

peer ip-address: Displays VPLS label block information received from a remote peer. The ip-address argument specifies the peer address.

vsi vsi-name: Displays VPLS label block information for a VSI. The vsi-name argument specifies the VSI name, a case-sensitive string of 1 to 31 characters. If you do not specify a VSI, this command displays VPLS label block information for all VSIs.

verbose: Displays detailed information. If you do not specify this keyword, the command displays brief information.

Usage guidelines

If you specify a peer, this command displays both the label block received from the peer and the local label block that matches the received label block.

If you do not specify a peer or the local keyword, this command displays label blocks received from all peers and local label blocks that match the received ones.

A local label block matches a received label block if the following condition is met: local label block LO ≤ remote site ID ≤ local label block LO + local label block LR – 1.

Examples

# Display brief information about label blocks received from all peers.

<Sysname> display l2vpn bgp

Total number of BGP PWs: 2, 2 up, 0 down

VSI Name: aaa

Rmt Site Offset RD Nexthop In/Out Label State

1 0 1:1 1.1.1.9 1419/1420 Up

3 0 1:1 3.3.3.9 1421/1282 Up

Table 6 Command output

Field	Description
Rmt Site	ID of the remote site.
Offset	Offset of the label block.

‌

# Display detailed information about label blocks received from all peers.

<Sysname> display l2vpn bgp verbose

VSI Name: aaa

Remote Site ID : 1

Offset : 0

RD : 1:1

PW State : Up

Encapsulation : BGP-VPLS

MTU : 1500

Nexthop : 1.1.1.9

Local VC Label : 1419

Remote VC Label : 1420

Link ID : 0x10000000

Local Label Block : 1418/10/0

Remote Label Block : 1418/10/0

Local Flow Label : Send

Reomote Flow Label : Recv

Export Route Target: 1:1

Table 7 Command output

Field	Description
Local VC Label	Incoming label of the PW.
Remote VC Label	Outgoing label of the PW.
Link ID	Link ID of the PW.
Local Label Block	Local label block: label base/label range/label-block offset.
Remote Label Block	Remote label block: label base/label range/label-block offset.
Local Flow Label	This field is not supported in the current software version. Flow label capability of the local PE: · Both—Flow label sending and receiving capabilities. · Send—Flow label sending capability. · Recv—Flow label receiving capability. This field display a hyphen (-) if the flow label feature is disabled.
Remote Flow Label	This field is not supported in the current software version. Flow label capability of the remote PE: · Both—Flow label sending and receiving capabilities. · Send—Flow label sending capability. · Recv—Flow label receiving capability. This field display a hyphen (-) if the flow label feature is disabled.
Export Route Target	Route target of the remote label block.

‌

# Display brief information about all local label blocks.

<Sysname> display l2vpn bgp local

VSI Name: aaa

Site Offset Range Label Base RD

2 0 10 1418 1:1

Table 8 Command output

Field	Description
Offset	Offset of the label block.
Range	Range of the label block.
Label Base	Initial value of the label block.
RD	RD of the label block. If no RD is configured, this field displays a hyphen (-).

‌

# Display detailed information about all local label blocks.

<Sysname> display l2vpn bgp local verbose

VSI Name: aaa

Site ID : 2

Offset : 0

RD : 1:1

Range : 10

Label Base : 1418

Link ID : 0x10000000,0x10000001,0x10000002

Table 9 Command output

Field	Description
Offset	Offset of the label block.
RD	RD of the label block. If no RD is configured, this field displays a hyphen (-).
Range	Range of the label block.
Label Base	Initial value of the label block.
Link ID	Link IDs of the PWs established using the label block.

‌

Related commands

display l2vpn pw

display l2vpn forwarding

Use display l2vpn forwarding to display L2VPN forwarding information.

Syntax

display l2vpn forwarding { ac | pw } [ vsi vsi-name ] [ slot slot-number ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

ac: Displays AC forwarding information.

pw: Displays PW forwarding information.

vsi vsi-name: Displays L2VPN forwarding information for a VSI. The vsi-name argument specifies the VSI name, a case-sensitive string of 1 to 31 characters. If you do not specify a VSI, this command displays L2VPN forwarding information for all VSIs.

slot slot-number: Specifies a card by its slot number. If you do not specify a card, this command displays L2VPN forwarding information for the active MPU.

verbose: Displays detailed information. If you do not specify this keyword, the command displays brief information.

Examples

# Display brief AC forwarding information for all VSIs.

<Sysname> display l2vpn forwarding ac

Total number of VSIs: 1

Total number of ACs: 2

AC VSI Name Link ID

XGE0/0/6 test 0x3

XGE0/0/7 test 0x4

Table 10 Command output

Field	Description
Total number of VSIs	Total number of VSIs, including VSIs that are not bound to any ACs.
AC	AC type: Layer 3 interface.
Link ID	Link ID of the AC in the VSI.

‌

# Display detailed AC forwarding information for all VSIs.

<Sysname> display l2vpn forwarding ac verbose

VSI Name: vpls1

Interface: XGE0/0/6

Link ID : 0x0

Access Mode : Ethernet

MAC limit : maximum=1024 alarm=enabled action=discard

Interface: XGE0/0/7

Link ID : 0x1

Access Mode : Ethernet

Redundancy Mode : All-active

DF State : DF

MAC limit : maximum=500 alarm=disabled action=forward

Table 11 Command output

Field	Description
Link ID	Link ID of the AC in the VSI.
Access Mode	AC access mode: · VLAN. · Ethernet.
AC Attributes	This field is not supported in the current software version. Hub-spoke attribute of the AC: · Hub link—The AC is the hub link in the VPLS hub-spoke network. · Spoke link—The AC is a spoke link in the VPLS hub-spoke network. This field is displayed only when the VSI bound to the AC has the hub-spoke attribute.
Redundancy Mode	Redundancy mode of the Ethernet segment (ES): · All-active—All-active mode. · Single-active—Single-active mode. This field is not displayed if the interface is not configured with an Ethernet Segment Identifier (ESI).
DF State	Designated forwarder (DF) role of the EVPN ES: · DF —The ES is a DF. · BDF—The ES is a backup designated forwarder (BDF). This field is not displayed if the interface is not configured with an ESI.
MAC limit	This field is not supported in the current software version. MAC address learning restrictions on the AC: · maximum—Maximum number of MAC addresses that the AC can learn. If no limit is set, this field displays unlimited. The default value is unlimited. · alarm—Status of alarm: enabled or disabled. The default value is disabled. · action—Action to be taken on frames with unknown source MAC addresses when the number of MAC addresses that the AC has learned reaches the maximum. The default value is forward. ¡ discard—Drops the frames. ¡ forward—Forwards the frames. The MAC limit field is not displayed if the maximum, alarm, and action parameters all use the default values.
E-Tree Role	This field is not supported in the current software version. The AC acts as a leaf AC in the E-Tree network. This field is not displayed if the AC acts as a root AC.

‌

# Display brief PW forwarding information for all VSIs.

<Sysname> display l2vpn forwarding pw

Total number of VSIs: 1

Total number of PWs: 2, 2 up, 0 blocked, 0 down

VSI Name In/Out Label NID Link ID State

aaa 1272/1275 1034 0x10000000 Up

aaa 1271/1273 1035 0x10000001 Up

Table 12 Command output

Field	Description
Total number of VSIs	Total number of VSIs, including VSIs that do not contain PWs.
In/Out Label	Incoming and outgoing labels of the PW. A hyphen (-) indicates that no label exists.
NID	NHLFE ID for the public tunnel that carries the PW. If equal-cost tunnels are available, this field displays multiple NIDs. If no tunnel is available, this field displays None.
Link ID	Link ID of the PW in the VSI.
State	PW state: Up, Down, or Blocked. Blocked indicates that the PW is blocked.

‌

# Display detailed PW forwarding information for all VSIs.

<Sysname> display l2vpn forwarding pw verbose

VSI Name: aaa

Link ID: 0x10000000

PW Type : VLAN PW State : Up

In Label : 1272 Out Label: 1275

MTU : 1500

PW Attributes : Main

VCCV CC : Router-Alert

VCCV BFD : Fault Detection with BFD

Flow Label : Send

Tunnel Group ID : 0x960000000

Tunnel NHLFE IDs: 1034

MAC limit : maximum=2000 alarm=enabled action=discard

Table 13 Command output

Field	Description
Link ID	Link ID of the PW in the VSI.
PW Type	Data encapsulation type of the PW.
PW State	PW state: Up, Down, or Blocked. Blocked indicates that the PW is blocked.
In Label	Incoming label of the PW. A hyphen (-) indicates that no label exists.
Out Label	Outgoing label of the PW. A hyphen (-) indicates that no label exists.
PW Attributes	PW attribute: · Main—The PW is the primary PW. · Backup—The PW is the backup PW. · No-split-horizon—Split horizon forwarding is disabled. This attribute is not supported in the current software version. · Hub link—The PW is the hub link in the VPLS hub-spoke network. This attribute is not supported in the current software version. · Spoke link—The PW is a spoke link in the VPLS hub-spoke network. This attribute is not supported in the current software version.
VCCV CC	VCCV CC type: · Control-Word—Control word. · Router-Alert—MPLS Router Alert Label. · TTL—TTL expiry (MPLS PW Label with TTL=1.) This field displays a hyphen (-) if no VCCV CC type is specified.
VCCV BFD	VCCV BFD type: · Fault Detection with BFD—BFD packets use IP/UDP encapsulation (with IP/UDP headers). · Fault Detection with Raw-BFD—BFD packets use PW-ACH encapsulation (without IP/UDP headers). This field displays a hyphen (-) if BFD is not used to verify PW connectivity.
Flow Label	This field is not supported in the current software version. Flow label capability: · Both—Flow label sending and receiving capabilities. · Send—Flow label sending capability. · Recv—Flow label receiving capability. This field display a hyphen (-) if the flow label feature is disabled.
Tunnel Group ID	ID of the tunnel group for the PW.
Tunnel NHLFE IDs	NHLFE ID of the public tunnel that carries the PW. If equal-cost tunnels are available, this field displays multiple NIDs. If no tunnel is available, this field displays None.
MAC limit	This field is not supported in the current software version. MAC address learning restrictions on the PW: · maximum—Maximum number of MAC addresses that the PW can learn. If no limit is set, this field displays unlimited. The default value is unlimited. · alarm—Status of alarm: enabled or disabled. The default value is disabled. · action—Action to be taken on frames with unknown source MAC addresses when the number of MAC addresses that the PW has learned reaches the maximum. The default value is forward. ¡ discard—Drops the frames. ¡ forward—Forwards the frames. The MAC limit field is not displayed if the maximum, alarm, and action parameters all use the default values.

‌

display l2vpn interface

Use display l2vpn interface to display L2VPN information for Layer 3 interfaces bound to VSIs.

Syntax

display l2vpn interface [ vsi vsi-name | interface-type interface-number ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

vsi vsi-name: Displays L2VPN information for the Layer 3 interfaces bound to a VSI. The vsi-name argument specifies the VSI name, a case-sensitive string of 1 to 31 characters.

interface-type interface-number: Displays L2VPN information for an interface specified by its type and number.

verbose: Displays detailed information. If you do not specify this keyword, the command displays brief information.

Usage guidelines

If you do not specify any parameters, this command displays L2VPN information for all Layer 3 interfaces bound to VSIs.

Examples

# Display brief L2VPN information for all Layer 3 interfaces bound to VSIs.

<Sysname> display l2vpn interface

Total number of interfaces: 2, 2 up, 0 down

Interface Owner Link ID State Type

XGE0/0/6 vpls1 0x1 Up VSI

XGE0/0/7 vpls1 0x2 Down VSI

Table 14 Command output

Field	Description
Owner	VSI name.
Link ID	Link ID of the AC in the VSI.
Type	L2VPN type. The value can only be VSI on a VPLS network.

‌

# Display detailed L2VPN information for all Layer 3 interfaces bound to VSIs.

<Sysname> display l2vpn interface verbose

Interface: XGE0/0/6

Owner : vsi1

Link ID : 0x0

State : Up

Type : VSI

Table 15 Command output

Field	Description
Owner	VSI name.
Link ID	Link ID of the AC in the VSI.
State	Physical status of the interface: Up or Down.
Type	L2VPN type. The value can only be VSI on a VPLS network.

‌

display l2vpn ldp

Use display l2vpn ldp to display LDP PW label information.

Syntax

display l2vpn ldp [ peer ip-address [ pw-id pw-id | vpls-id vpls-id ] | vsi vsi-name ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

peer ip-address: Displays information about PW labels advertised by a peer PE through LDP. The ip-address argument specifies the LSR ID of the peer PE. If you do not specify a peer PE, this command displays information about LDP PW labels advertised by all peer PEs.

pw-id pw-id: Displays FEC 128 LDP PW label information for a PW. The pw-id argument specifies the PW ID in the range of 1 to 4294967295. If you specify the peer ip-address option without the pw-id pw-id option, this command displays all LDP PW label information advertised by the specified peer PE.

vpls-id vpls-id: Displays FEC 129 LDP PW label information for a VPLS instance. The vpls-id argument specifies the VPLS instance ID, a string of 3 to 21 characters. You can specify a VPLS ID in one of the following formats:

· 16-bit AS number:32-bit user-defined number. For example, 101:3.

· 32-bit IP address:16-bit user-defined number. For example, 192.168.122.15:1.

· 32-bit AS number:16-bit user-defined number, where the AS number must be equal to or greater than 65536. For example, 65536:1.

vsi vsi-name: Displays LDP PW label information for a VSI. The vsi-name argument specifies the VSI name, a case-sensitive string of 1 to 31 characters. If you do not specify a VSI, this command displays LDP PW label information for all VSIs.

verbose: Displays detailed information. If you do not specify this keyword, the command displays brief information.

Usage guidelines

LDP advertises FEC-to-PW label bindings in the following ways:

· After you specify a remote PE with the peer command, LDP advertises an FEC 128-to-PW label binding to the remote PE.

· After BGP discovers a remote PE, LDP advertises an FEC 129-to-PW label binding to the remote PE.

This command can display PW labels as follows:

· If you specify the pw-id pw-id option, this command displays PW labels for FEC 128.

· If you specify the vpls-id vpls-id option, this command displays PW labels for FEC 129.

· If you do not specify pw-id pw-id or vpls-id vpls-id, this command displays PW labels for both FEC 128 and FEC 129.

Examples

# Display brief information about all PW labels advertised by LDP.

<Sysname> display l2vpn ldp

Total number of LDP PWs: 2, 2 up, 0 down

Peer PW ID/VPLS ID In/Out Label State Owner

192.3.3.3 1001 775125/775126 Up vpls1

192.3.3.3 1003 775117/775122 Up vpls3

Table 16 Command output

Field	Description
PW ID/VPLS ID	PW ID for FEC 128, or VPLS ID of the PE for FEC 129.
State	PW state: Up or Down.
Owner	Name of the VSI to which the PW belongs.

‌

# Display detailed information about all PW labels advertised by LDP.

<Sysname> display l2vpn ldp verbose

Peer: 2.2.2.9 PW ID: 500

VSI Name: ccc

PW State: Up

PW Status Communication: Notification method

PW Preferential Forwarding Status Bit: Process

PW ID FEC (Local/Remote):

PW Type : VLAN/VLAN

Group ID : 0/0

Label : 1552/1552

Control Word: Disabled/Disabled

VCCV CV Type: -/-

VCCV CC Type: -/-

Flow Label : Send/Recv

MTU : 1500/1500

PW Status : PW forwarding/PW forwarding

Peer: 2.2.2.9 VPLS ID: 100:100

VSI Name: bbb

PW State: Up

PW Status Communication: Notification method

PW ID FEC (Local/Remote):

Local AII : (1.1.1.9, 2.2.2.9)

Remote AII : (2.2.2.9, 1.1.1.9)

PW Type : VLAN/VLAN

Group ID : 0/0

Label : 1553/1553

Control Word: Disabled/Disabled

VCCV CV Type: -/-

VCCV CC Type: -/-

Flow Label : Both/Both

MTU : 1500/1500

PW Status : PW forwarding/PW forwarding

Table 17 Command output

Field	Description
PW Status Communication	PW status communication method: · Notification method—Notifies the PW status through Notification messages. · Label withdraw method—Assigns a PW label to the PW when the AC associated with PW comes up, and withdraws the PW label when the AC goes down.
PW Preferential Forwarding Status Bit	PW state processing mode: · Process—Process the received PW states. · Ignore—Ignore the received PW states.
PW ID FEC (Local/Remote)	PW ID FEC information advertised from the local PE to the peer PE/PW ID FEC information advertised from the peer PE to the local PE.
VCCV CV Type	VCCV CV type: · LSP Ping—Uses MPLS LSP ping to verify PW connectivity. · BFD—Uses BFD to verify PW connectivity. BFD packets use IP/UDP encapsulation (with IP/UDP headers). · Raw-BFD—Uses BFD to verify PW connectivity. BFD packets use PW-ACH encapsulation (without IP/UDP headers). This field displays a hyphen (-) if VCCV is not performed on the PW.
VCCV CC Type	VCCV CC type: · Control-Word—Control word. · Router-Alert—MPLS Router Alert Label. · TTL—TTL expiry (MPLS PW Label with TTL=1.) This field displays a hyphen (-) if no VCCV CC type is specified. VCCV is an MPLS OAM technology. For more information about VCCV, see MPLS Configuration Guide.
Flow Label	This field is not supported in the current software version. Flow label capability: · Both—Flow label sending and receiving capabilities. · Send—Flow label sending capability. · Recv—Flow label receiving capability. This field display a hyphen (-) if the flow label feature is disabled.
MTU	Maximum transmission unit of the VSI.
PW Status	PW status: · PW forwarding—PW is ready for packet forwarding. · PW not forwarding—PW is not ready for packet forwarding. · AC receive fault—AC cannot receive packets. · AC transmit fault—AC cannot send packets. · PW receive fault—PW cannot receive packets. · PW transmit fault—PW cannot send packets. · PW standby—The PW is in standby state. · PW request switchover—The PW is requesting a switchover. · Unknown—Unknown protocol.
VPLS ID	ID of the VPLS instance.
Local AII	Source Attachment Individual Identifier (SAII) and Target Attachment Individual Identifier (TAII) advertised to the remote PE.
Remote AII	SAII and TAII received from the remote PE.

‌

display l2vpn mac-address

Use display l2vpn mac-address to display MAC address entries for L2VPNs.

Syntax

display l2vpn mac-address [ vsi vsi-name ] [ dynamic ] [ count | verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

vsi vsi-name: Specifies a VSI by its name, a case-sensitive string of 1 to 31 characters. If you do not specify the ac and pw keywords, this command displays all MAC address entries in the specified VSI.

dynamic: Displays dynamically generated MAC address entries. If you do not specify this keyword, the command displays all types of MAC address entries. The device supports only dynamic MAC address entries in the current software version.

count: Displays the number of the MAC address entries. If you do not specify this keyword, the command displays detailed information about the MAC address entries.

verbose: Displays detailed MAC address entry information. If you do not specify this keyword, the command displays brief MAC address entry information.

Usage guidelines

If you do not specify the interface interface-type interface-number, peer ip-address pw-id pw-id, and vsi vsi-name options, this command displays MAC address entries for all L2VPNs.

Examples

# Display MAC address entries for all L2VPNs.

<Sysname> display l2vpn mac-address

MAC Address State VSI Name Link ID/Name Aging

0000-0000-000a Dynamic vpn1 0x10000000 Aging

0000-0000-0009 Dynamic vpn1 0x10000001 Aging

--- 2 mac address(es) found ---

# Display the total number of MAC address entries for all L2VPNs.

<Sysname> display l2vpn mac-address count

2 mac address(es) found

Table 18 Command output

Field	Description
State	MAC address type. The MAC address type can only be Dynamic in the current software version, which indicates that the MAC address is dynamically learned.
Link ID/Name	The Link ID field represents the outgoing link ID of the MAC address entry. It is the link ID of the AC or PW in the VSI. The Name field applies to a VXLAN VSI. VPLS VSIs do not support the Name field.
Aging	Whether the MAC address entry will be aged.
XX mac address(es) found	Total number of MAC address entries.

‌

# Display detailed information about all MAC address entries.

<Sysname> display l2vpn mac-address verbose

MAC Address : 0000-0000-000b

VSI Name : vpn1

VXLAN ID : -

Interface : XGE0/0/6

Link ID : 1

State : Dynamic

Aging : Aging

Table 19 Command output

Field	Description
VSI Name	Name of the VSI to which the MAC address belongs.
VXLAN ID	VPLS does not support this field.
Interface	For the local site, if the AC of the MAC address is a Layer 3 interface, this field displays the name of the Layer 3 interface. For the remote site, this field displays a hyphen (-).
Link ID	Link ID of the AC or PW in the VSI.
State	MAC address type. The MAC address type can only be Dynamic in the current software version, which indicates that the MAC address is dynamically learned.
Aging	Whether the MAC address entry will be aged.

‌

Related commands

reset l2vpn mac-address

display l2vpn pw

Use display l2vpn pw to display L2VPN PW information.

Syntax

display l2vpn pw [ vsi vsi-name ] [ protocol { bgp | ldp | static } ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

vsi vsi-name: Displays L2VPN PW information for a VSI. The vsi-name argument specifies the VSI name, a case-sensitive string of 1 to 31 characters. If you do not specify a VSI, this command displays L2VPN PW information for all VSIs.

protocol: Displays PWs created by a signaling protocol. If you do not specify a protocol, this command displays PWs created by all protocols.

bgp: Displays BGP PW information.

ldp: Displays LDP PW information, including PWs for FEC 128 (LDP PWs) and FEC 129 (BGP auto-discovery LDP PWs).

static: Displays static PW information.

verbose: Displays detailed information. If you do not specify this keyword, the command displays brief information.

Usage guidelines

After you enable PW statistics, you can use the display l2vpn pw verbose command to display PW statistics.

Examples

# Display brief information about all PWs.

<Sysname> display l2vpn pw

Flags: M - main, B - backup, E - ecmp, BY - bypass, H - hub link, S - spoke link

N - no split horizon, A - administration, ABY – ac-bypass

PBY – pw-bypass

Total number of PWs: 5

5 up, 0 blocked, 0 down, 0 defect, 0 idle, 0 duplicate

VSI Name: aaa

Peer PWID/RmtSite/SrvID In/Out Label Proto Flag Link ID State

2.2.2.9 2 1420/1419 BGP M 10000000 Up

3.3.3.9 3 1421/1281 BGP M 10000001 Up

Table 20 Command output

Field	Description
PWID/RmtSite/SrvID	This field displays the following: · PW ID for an LDP PW (FEC 128) or a static PW. · A hyphen (-) for a BGP auto-discovery LDP PW (FEC 129). · Remote site ID for a BGP PW. · Remote service ID for an EVPN PW.
Proto	Protocol used to establish the PW: LDP, Static, or BGP.
Flag	PW attribute flag: · M—Primary PW. · B—Backup PW. · E—ECMP PW. (This value does not apply to VPLS.) · BY—Bypass PW. (This value does not apply to VPLS.) · H—The PW is the hub link in the VPLS hub-spoke network. This attribute is not supported in the current software version. · S—The PW is a spoke link in the VPLS hub-spoke network. This attribute is not supported in the current software version. · N—Split horizon forwarding is disabled. This attribute is not supported in the current software version. · A—The PW is an administration PW. · ABY—The PW is a bypass PW for AC bypass. (This value does not apply to VPLS.) · PBY—The PW is a bypass PW for PW bypass. (This value does not apply to VPLS.)
Link ID	Link ID of the PW in the VSI.
State	PW state: · Up—The PW is available. · Down—The PW is not available. · Blocked—The PW is a backup PW. · Defect—BFD has detected a defect on the PW. · Idle—The incoming label of the PW is not available. · Dup—The incoming label of the static PW is occupied by a static LSP or a static CRLSP.

‌

# Display detailed information about all L2VPN PWs.

<Sysname> display l2vpn pw verbose

VSI Name: aaa

Peer: 2.2.2.9 Remote Site: 2

Signaling Protocol : BGP

Link ID : 0x10000001 PW State : Up

In Label : 1420 Out Label: 1419

MTU : 1500

PW Attributes : Main

VCCV CC : -

VCCV BFD : -

Flow Label : -

Tunnel Group ID : 0x800000960000000

Tunnel NHLFE IDs : 1038

VSI Name: bbb

Peer: 2.2.2.9 VPLS ID: 100:100

Signaling Protocol : LDP

Link ID : 0x10000000 PW State : Up

In Label : 1553 Out Label: 1553

MTU : 1500

PW Attributes : Main

VCCV CC : -

VCCV BFD : -

Flow Label : -

Tunnel Group ID : 0x800000960000000

Tunnel NHLFE IDs : 1038

Admin PW : Associated AC interface Loop0

VSI Name: ccc

Peer: 2.2.2.9 PW ID: 500

Signaling Protocol : LDP

Link ID : 0x10000000 PW State : Up

In Label : 1552 Out Label: 1552

MTU : 1500

PW Attributes : Main

VCCV CC : -

VCCV BFD : -

Flow Label : -

Tunnel Group ID : 0x800000960000000

Tunnel NHLFE IDs : 1038

Admin PW : -

Table 21 Command output

Field	Description
Peer	IP address of the peer PE to which the PW is destined.
Signaling Protocol	Protocol used to establish the PW: LDP, Static, or BGP.
Link ID	Link ID of the PW in the VSI.
PW State	PW state: · Up—The PW is available. · Down—The PW is not available. · Blocked—The PW is a backup PW. · Defect—BFD has detected a defect on the PW. · Idle—The incoming label of the PW is not available. · Duplicate—The incoming label of the static PW is occupied by a static LSP or a static CRLSP.
Wait to Restore Time	Wait time to switch traffic from the backup PW to the primary PW when the primary PW recovers, in seconds. If the switchover is disabled, this field displays Infinite. This field is available when both primary and backup PW exist, and is displayed only for the primary PW.
Remaining Time	Remaining wait time for traffic switchover, in seconds. This field is displayed after the switchover wait timer is started.
MTU	Negotiated MTU of the PW.
PW Attributes	PW attribute: · Main—The PW is the primary PW. · Backup—The PW is the backup PW. · Administration—Administration PW. · Hub link—The PW is the hub link in the VPLS hub-spoke network. This attribute is not supported in the current software version. · Spoke link—The PW is a spoke link in the VPLS hub-spoke network. This attribute is not supported in the current software version. · No-split-horizon—Split horizon forwarding is disabled. This attribute is not supported in the current software version.
VCCV CC	VCCV CC type: · Control-Word—Control word. · Router-Alert—MPLS Router Alert Label. · TTL—TTL expiry (MPLS PW Label with TTL=1.) This field displays a hyphen (-) if no VCCV CC type is specified.
VCCV BFD	VCCV BFD type: · Fault Detection with BFD—BFD packets use IP/UDP encapsulation (with IP/UDP headers). · Fault Detection with Raw-BFD—BFD packets use PW-ACH encapsulation (without IP/UDP headers). This field displays a hyphen (-) if BFD is not used to verify PW connectivity.
Flow Label	This field is not supported in the current software version. Flow label capability: · Both—Flow label sending and receiving capabilities. · Send—Flow label sending capability. · Recv—Flow label receiving capability. This field display a hyphen (-) if the flow label feature is disabled.
Tunnel Group ID	ID of the tunnel group for the PW.
Tunnel NHLFE IDs	NHLFE ID of the public tunnel that carries the PW. If equal-cost tunnels are available, this field displays multiple NIDs. If no tunnel is available, this field displays None.
Admin PW	Administration PW to which the PW is bound. This field displays a hyphen (-) if the PW is not bound to an administration PW.
VPLS ID	ID of the VPLS instance.
Remote Site	ID of the remote site.
Down Reasons	Reason why the PW went down: · BFD session for PW down. · BGP RD was deleted. · BGP RD was empty. · Control word not match. · Encapsulation not match. · Label not allocated. · LDP interface parameter not match. · Local and remote LDP PWs have different AII. · Non-existent remote LDP PW—The remote end has deleted the LDP PW. · Local AC Down. · Local AC was non-existent—Local AC was not configured. · Local LDP PW VN defect—Local LDP PW had VN defects. · Local LDP PW was not sent mapping message—The local end did not send LDP mapping messages. · Local VSI Down. · MTU not match. · Remote AC Down. · Remote LDP PW VN defect—Remote LDP PW had VN defects. · PW down after created—The PW is in down state after being created. · Tunnel Down.
Color	This field is not supported in the current software version. Color attribute expected to be recursed to the SR-MPLS TE policy. If no color attribute exists, this field displays a hyphen (-). This field is displayed only for EVPN PWs.

‌

display l2vpn pw-class

Use display l2vpn pw-class to display PW class information.

Syntax

display l2vpn pw-class [ class-name ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

class-name: Displays information about the PW class specified by its name, a case-sensitive string of 1 to 19 characters. If you do not specify a PW class, this command displays information about all PW classes.

verbose: Displays detailed PW class information. If you do not specify this keyword, the command displays brief PW class information.

Examples

# Display information about all PW classes.

<Sysname> display l2vpn pw-class

Total number of PW classes: 2

PW Class Name PW Type Control Word VCCV CC VCCV BFD

pw1 Ethernet Enabled Control-Word BFD

pw2 VLAN Disabled Control-Word BFD

Table 22 Command output

Field	Description
VCCV CC	VCCV CC type: · Control-Word—Control word. · Router-Alert—MPLS Router Alert Label. · TTL—TTL expiry (MPLS PW Label with TTL=1.) This field displays a hyphen (-) if no VCCV CC type is specified.
VCCV BFD	VCCV BFD type: · Fault Detection with BFD—BFD packets use IP/UDP encapsulation (with IP/UDP headers). · Fault Detection with Raw-BFD—BFD packets use PW-ACH encapsulation (without IP/UDP headers). This field displays a hyphen (-) if BFD is not used to verify PW connectivity.

Field

Description

VCCV CC

VCCV CC type:

· Control-Word—Control word.

· Router-Alert—MPLS Router Alert Label.

· TTL—TTL expiry (MPLS PW Label with TTL=1.)

This field displays a hyphen (-) if no VCCV CC type is specified.

VCCV BFD

VCCV BFD type:

· Fault Detection with BFD—BFD packets use IP/UDP encapsulation (with IP/UDP headers).

· Fault Detection with Raw-BFD—BFD packets use PW-ACH encapsulation (without IP/UDP headers).

This field displays a hyphen (-) if BFD is not used to verify PW connectivity.

‌

# Display detailed information about all PW classes.

<Sysname> display l2vpn pw-class verbose

PW Class Name : pw1

PW Type : Ethernet

Control Word: Enabled

VCCV CC : Router-Alert

VCCV BFD : BFD

Sequencing : -

Flow Label : -

PW Class Name : pw2

PW Type : VLAN

Control Word: Disabled

VCCV CC : Router-Alert

VCCV BFD : BFD

Sequencing : -

Flow Label : -

Table 23 Command output

Field	Description
PW Type	PW data encapsulation type. Options include Ethernet, VLAN, TDM-CESoPSN-Basic, and TDM-SAToP-E1.
VCCV CC	VCCV CC type: · Control-Word—Control word. · Router-Alert—MPLS Router Alert Label. · TTL—TTL expiry (MPLS PW Label with TTL=1.) This field displays a hyphen (-) if no VCCV CC type is specified.
VCCV BFD	VCCV BFD type: · BFD—BFD packets use IP/UDP encapsulation (with IP/UDP headers). · Raw-BFD—BFD packets use PW-ACH encapsulation (without IP/UDP headers). This field displays a hyphen (-) if BFD is not used to verify PW connectivity.
Sequencing	Packet sequencing on the PW. The value is Both, which means sequencing is enabled for both incoming and outgoing packets on a PW. A hyphen (-) in this field indicates that packet sequencing is disabled on the PW.
Flow Label	This field is not supported in the current software version. Flow label capability: · Both—Flow label sending and receiving capabilities. · Send—Flow label sending capability. · Recv—Flow label receiving capability. This field display a hyphen (-) if the flow label feature is disabled.

‌

Related commands

pw-class

display l2vpn vsi

Use display l2vpn vsi to display VSI information.

Syntax

display l2vpn vsi [ name vsi-name | verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

name vsi-name: Displays information about a VSI. The vsi-name argument specifies the VSI name, a case-sensitive string of 1 to 31 characters. If you do not specify a VSI, this command displays information about all VSIs.

verbose: Displays detailed information. If you do not specify this keyword, the command displays brief information.

Examples

# Display brief information about all VSIs.

<Sysname> display l2vpn vsi

Total number of VSIs: 2, 1 up, 1 down, 0 admin down

VSI Name VSI Index MTU State

vpls1 0 1500 Up

vpls2 1 1500 Down

# Display VSI statistics.

<Sysname> display l2vpn vsi count

Total number of VSIs: 1, 1 up, 0 down, 0 admin down

Table 24 Command output

Field	Description
State	VSI state: · Up. · Down. · Admin down—The VSI is manually brought down by using the shutdown command.

Field

Description

State

VSI state:

· Up.

· Down.

· Admin down—The VSI is manually brought down by using the shutdown command.

‌

# Display detailed information about all VSIs.

<Sysname> display l2vpn vsi verbose

VSI Name: vpls1

VSI Index : 0

VSI Description : vsi for vpls1

VSI State : Up

MTU : 1500

Diffserv Mode : -

Bandwidth : Unlimited

Broadcast Restrain : -

Multicast Restrain : -

Unknown Unicast Restrain: -

MAC Learning : Enabled

MAC Table Limit : Unlimited

MAC Learning rate : Unlimited

Drop Unknown : Disabled

PW Redundancy Mode : Independent

Flooding : Enabled

VXLAN ID : -

LDP PWs:

Peer PW ID Link ID State

192.3.3.3 1 0x10000000 Up

192.3.3.3 1001 0x10000000 Blocked

BGP PWs:

Peer Remote Site Link ID State

192.4.4.4 1 0x10000001 Up

ACs:

AC Link ID State

XGE0/0/6 0x1 Up

Table 25 Command output

Field	Description
VSI Description	If no description is configured for the VSI, this field is not displayed.
VSI State	VSI state: · Up. · Down. · Admin down—The VSI is manually brought down by using the shutdown command.
Diffserv Mode	DiffServ mode. Options include the following: · ingress—MPLS DiffServ mode for the inbound direction. · egress—MPLS DiffServ mode for the outbound direction. · pipe—Pipe mode. · short-pipe—Short-pipe mode. · uniform—Uniform mode · trust—Priority trust mode ¡ inner-dot1p—Trusts the inner 802.1p priority in packets. ¡ dscp—Trusts the DSCP in packets. af1, af2, af3, af4, be, cs6, cs7, or ef represents the MPLS EXP value. If no DiffServ mode is configured, this field displays a hyphen (-).
Bandwidth	This field is not supported in the current software version. Maximum bandwidth for known unicast traffic in the VSI, in kbps.
Broadcast Restrain	This field is not supported in the current software version. Broadcast suppression bandwidth for the VSI, in kbps.
Multicast Restrain	This field is not supported in the current software version. Multicast suppression bandwidth for the VSI, in kbps.
Unknown Unicast Restrain	This field is not supported in the current software version. Unknown unicast suppression bandwidth for the VSI, in kbps.
MAC Table Limit	Maximum number of MAC addresses that the VSI can learn. This field displays Unlimited if no limit is set on the number of MAC addresses that the VSI can learn.
MAC Learning rate	MAC address learning rate of the VSI.
Drop Unknown	Whether the VSI drops packets with unknown source MAC addresses after it has leaned the maximum number of MAC addresses: · Enabled—Drops packets with unknown source MAC addresses. · Disabled—Forwards packets with unknown source MAC addresses.
PW Redundancy Mode	PW redundancy operation mode: · Slave—Master/slave mode and the local PE operates as the slave node. · Master—Master/slave mode and the local PE operates as the master node. · Independent—Independent mode.
Hub-Spoke	This field is not supported in the current software version. Hub-spoke capability. If the hub-spoke capability is enabled, this field displays Enabled. If the hub-spoke capability is disabled, this field is not displayed.
Flooding	VPLS does not support this field.
VXLAN ID	VPLS does not support this field.
State	PW state: Up, Down, Blocked, or BFD Defect.
AC	AC type: Layer 3 interface.

‌

Related commands

vsi

l2vpn enable

Use l2vpn enable to enable L2VPN.

Use undo l2vpn enable to disable L2VPN.

Syntax

l2vpn enable

undo l2vpn enable

Default

L2VPN is disabled.

Views

System view

Predefined user roles

network-admin

Usage guidelines

You must enable L2VPN before configuring other L2VPN settings.

Examples

# Enable L2VPN.

<Sysname> system-view

[Sysname] l2vpn enable

l2vpn log enable

Use l2vpn log enable to enable L2VPN logging.

Use undo l2vpn log enable to disable L2VPN logging.

Syntax

l2vpn log enable

undo l2vpn log enable

Default

L2VPN logging is enabled.

Views

System view

Predefined user roles

network-admin

Usage guidelines

This feature enables L2VPN to generate logs for running state changes. The generated logs are sent to the information center. The information center processes the logs according to user-defined output rules (whether to output logs and where to output).

For more information about the information center, see information center configuration in Network Management and Monitoring Configuration Guide.

Examples

# Enable L2VPN logging.

<Sysname> system-view

[Sysname] l2vpn log enable

l2vpn switchover

Use l2vpn switchover to switch traffic from a PW to its backup or primary PW.

Syntax

l2vpn switchover peer ip-address pw-id pw-id

Views

User view

Predefined user roles

network-admin

Parameters

peer ip-address: Specifies the LSR ID of the peer PE.

pw-id pw-id: Specifies a PW by its ID in the range of 1 to 4294967295.

Usage guidelines

The specified LSR ID and PW ID uniquely identify a PW.

If a PW has a backup PW or primary PW, this command switches traffic from the PW to the backup or primary PW. If the PW does not have a backup or primary PW, this command does not perform the switchover.

Examples

# Switch traffic from PW 100 destined for 3.3.3.3 to its backup PW.

<Sysname> l2vpn switchover peer 3.3.3.3 pw-id 100

mac-learning enable

Use mac-learning enable to enable MAC address learning for a VSI.

Use undo mac-learning enable to disable MAC address learning for a VSI.

Syntax

mac-learning enable

undo mac-learning enable

Default

MAC address learning is enabled for a VSI.

Views

VSI view

Predefined user roles

network-admin

Usage guidelines

If MAC address learning is disabled for a VSI, the VSI does not learn the source MAC addresses of received packets.

Examples

# Disable MAC address learning for VSI vpn1.

<Sysname> system-view

[Sysname] vsi vpn1

[Sysname-vsi-vpn1] undo mac-learning enable

Related commands

display l2vpn vsi

peer

Use peer in VSI LDP signaling view to configure a VSI LDP PW and enter its view, or enter the view of an existing VSI LDP PW.

Use peer in VSI static configuration view to configure a VSI static PW and enter its view, or enter the view of an existing VSI static PW.

Use undo peer to delete a VPLS PW.

Syntax

In VSI LDP signaling view:

peer ip-address [ pw-id pw-id ] [ ignore-standby-state | pw-class class-name | tunnel-policy tunnel-policy-name ] *

undo peer ip-address pw-id pw-id

In VSI static configuration view:

peer ip-address [ pw-id pw-id ] [ in-label label-value out-label label-value [ pw-class class-name | tunnel-policy tunnel-policy-name ] * ]

undo peer ip-address pw-id pw-id

Default

No PWs exist for VPLS.

Views

VSI LDP signaling view

VSI static configuration view

Predefined user roles

network-admin

Parameters

ip-address: Specifies the LSR ID of the peer PE.

pw-id pw-id: Specifies a PW ID for the PW, in the range of 1 to 4294967295.

in-label label-value: Specifies the incoming label of the PW. The value range for the label-value argument is 16 to 2047.

out-label label-value: Specifies the outgoing label of the PW, in the range of 16 to 1048575.

ignore-standby-state: Ignores the PW active/standby status bit received from the remote PE. If you do not specify this keyword, the local PE does not ignore the PW active/standby status bit received from the remote PE. This keyword is applicable only to LDP PWs.

pw-class class-name: Specifies a PW class by its name, a case-sensitive string of 1 to 19 characters. You can specify a PW class to configure the PW data encapsulation type and control word. If you do not specify a PW class, the PW data encapsulation type is VLAN and the PW does not support control word.

tunnel-policy tunnel-policy-name: Specifies a tunnel policy by its name, a case-insensitive string of 1 to 19 characters. If you do not specify a tunnel policy, the PW uses the default tunnel policy.

Usage guidelines

A PE uses the PW Preferential Forwarding Status bit in LDP messages to advertise the local PWs' active/standby states. When the bit is set, it indicates that the local PW is in standby state. When the bit is cleared, it indicates that the local PW is in active state.

In independent mode, a PE considers the status bits received from the remote PEs when it selects the the forwarding PW among the set of redundant PWs. If you specify the ignore-standby-state keyword, the PE ignores the status bits received from the remote PEs and selects the forwarding PW using its own local rule.

In master/slave mode, a slave PE selects the forwarding PW among the set of redundant PWs based on the status bit received from the remote PEs. If you specify the ignore-standby-state keyword, the PE ignores the status bit received from the remote PEs and uses the primary PW to forward packets as long as the primary PW is up.

To create a static PW, you must specify the incoming and outgoing labels. To enter VSI static PW view of an existing static PW, you do not need to specify the incoming and outgoing labels.

The PW ID for a PW must be the same on the PEs at the ends of the PW.

On a PE, the LSR ID of the peer PE and the PW ID uniquely identify a PW. The peer LSR ID and PW ID combination of a PW must be unique among all VPLS PWs and cross-connect PWs.

If both the default PW ID in the default-pw-id command and a PW ID in the peer command are configured, the PW ID in the peer command is used. If only the default PW ID is configured, the default PW ID is used. If no default PW ID is configured, you must provide a PW ID in the peer command.

Examples

# Configure an LDP PW for VSI vpn1 and enter VSI LDP PW view: specify the peer PE address as 4.4.4.4, and set the PW ID to 200.

<Sysname> system-view

[Sysname] vsi vpn1

[Sysname-vsi-vpn1] pwsignaling ldp

[Sysname-vsi-vpn1-ldp] peer 4.4.4.4 pw-id 200

[Sysname-vsi-vpn1-ldp-4.4.4.4-200]

# Configure a static PW for VSI vpn1 and enter VSI static PW view: specify the peer PE address as 5.5.5.5, and set the PW ID to 200, incoming label to 100, and outgoing label to 200.

<Sysname> system-view

[Sysname] vsi vpn1

[Sysname-vsi-vpn1] pwsignaling static

[Sysname-vsi-vpn1-static] peer 5.5.5.5 pw-id 200 in-label 100 out-label 200

[Sysname-vsi-vpn1-static-5.5.5.5-200]

Related commands

default-pw-id

display l2vpn ldp

display l2vpn pw

pw-class

tunnel-policy

pw-class (auto-discovery VSI view)

Use pw-class to specify a PW class for an auto-discovery VSI.

Use undo pw-class to restore the default.

Syntax

pw-class class-name

undo pw-class

Default

No PW class is specified.

Views

Auto-discovery VSI view

Predefined user roles

network-admin

Parameters

class-name: Specifies a PW class by its name, a case-sensitive string of 1 to 19 characters.

Usage guidelines

The specified PW class will be used to establish all PWs on the auto-discovery VSI.

Examples

# Specify a PW class named pw100 for auto-discovery VSI aaa.

<Sysname> system-view

[Sysname] pw-class pw100

[Sysname-pw-pw100] quit

[Sysname] vsi aaa

[Sysname-vsi-aaa] auto-discovery bgp

[Sysname-vsi-aaa-auto] pw-class pw100

Related commands

control-word enable

display l2vpn pw-class

pw-type

pw-class (system view)

Use pw-class to create a PW class and enter its view, or enter the view of an existing PW class.

Use undo pw-class to delete a PW class.

Syntax

pw-class class-name

undo pw-class class-name

Default

No PW classes exist.

Views

System view

Predefined user roles

network-admin

Parameters

class-name: Specifies a name for the PW class, a case-sensitive string of 1 to 19 characters.

Usage guidelines

In PW class view, you can configure PW attributes such as the PW data encapsulation type and whether to enable control word. A PW class simplifies PW attribute configuration for PWs that have the same PW attributes. You can configure the PW attributes in a PW class, and specify the PW class for the PWs.

Examples

# Create a PW class named pw100 and enter PW class view.

<Sysname> system-view

[Sysname] pw-class pw100

[Sysname-pw-pw100]

Related commands

control-word enable

display l2vpn pw-class

pw-type

pw-redundancy

Use pw-redundancy to specify a PW redundancy operation mode.

Use undo pw-redundancy to restore the default.

Syntax

pw-redundancy { independent | master }

undo pw-redundancy

Default

The PW redundancy operation mode is master/slave and the local PE operates as the slave node.

Views

VSI LDP signaling view

Predefined user roles

network-admin

Parameters

Independent: Specifies the independent PW redundancy operation mode.

master: Specifies the master/slave PW redundancy operation mode and uses the local PE as the master node.

Usage guidelines

This command is applicable only to LDP PWs.

LDP PWs support the independent and master/slave PW redundancy operation modes.

· Independent mode—The two PEs of a PW use LDP to advertise their respective PW active/standby state to each other. A PW can forward traffic only when it is up and active at both ends of the PW. In this mode, make sure both PEs of a PW use the independent PW redundancy operation mode.

· Master/slave mode—One PE of a PW operates as the master node and the other PE operates as the slave node. The master PE determines the PW active/standby state and then uses LDP to advertise the PW state to the slave PE. The slave PE uses the same PW state as the master PE based on the information received from the master PE. In this way, the master and slave PEs for the set of redundant PWs can use the same active PW to forward user packets.

A slave node does not advertise the PW active/standby state to the master node, and the master node ignores the PW active/standby state received from the slave nodes.

Examples

# In VSI LDP signaling view, specify the master/slave PW redundancy operation mode and use the local PE as the master node.

<Sysname> system-view

[Sysname] vsi aaa

[Sysname-vsi-aaa] pwsignaling ldp

[Sysname-vsi-aaa-ldp] pw-redundancy master

Related commands

backup-peer

display l2vpn ldp

display l2vpn pw

peer

pwsignaling

Use pwsignaling to specify a PW signaling protocol for a VSI, and enter the VSI signaling protocol view.

Use undo pwsignaling to remove the specified PW signaling protocol for a VSI.

Syntax

pwsignaling { ldp | static }

undo pwsignaling { ldp | static }

Default

No PW signaling protocol is specified for a VSI.

Views

VSI view

Predefined user roles

network-admin

Parameters

ldp: Establishes PWs through LDP (FEC 128) and enters VSI LDP signaling view.

static: Establishes PWs statically and enters VSI static configuration view.

Examples

# Configure VSI vpn1 to use LDP to establish LDP PWs, and enter VSI LDP signaling view.

<Sysname> system-view

[Sysname] vsi vpn1

[Sysname-vsi-vpn1] pwsignaling ldp

[Sysname-vsi-vpn1-ldp]

Related commands

display l2vpn pw

pw-type

Use pw-type to specify a PW data encapsulation type for a PW class.

Use undo pw-type to restore the default.

Syntax

pw-type { ethernet | vlan } [ force-for-vpls ]

undo pw-type

Default

The PW data encapsulation type for a PW class is VLAN.

Views

PW class view

Predefined user roles

network-admin

Parameters

ethernet: Specifies the PW data encapsulation type as Ethernet.

vlan: Specifies the PW data encapsulation type as VLAN.

force-for-vpls: Forces VPLS to use and advertise the specified encapsulation type (Ethernet or VLAN). If you do not specify this keyword, the device always advertises the BGP-VPLS encapsulation type for VPLS BGP PW establishment.

Usage guidelines

When the PW data encapsulation type is Ethernet, the PE encapsulates packets forwarded between the AC and PW as follows:

· Traffic from the AC to the PW cannot carry the P-tag assigned by the service provider.

¡ If traffic from the AC has the P-tag, the PE removes the P-tag, and adds a PW label and an outer tag into the packet before forwarding it.

¡ If traffic from the AC does not have the P-tag, the PE adds a PW label and an outer tag into the packet before forwarding it.

· For traffic received from the PW:

¡ If the AC access mode is VLAN, the PE adds the P-tag and forwards the traffic through the AC.

¡ If the AC access mode is Ethernet, the PE directly forwards the traffic through the AC. The PE cannot modify or delete the P-tag for the traffic from the PW.

When the PW data encapsulation type is VLAN, the PE encapsulates packets forwarded between the AC and PW as follows:

· Traffic from the AC to the PW must carry the P-tag.

¡ If traffic from the AC has the P-tag, the PE performs one of the following operations:

- Keeps the P-tag when the peer PE does not require the ingress to modify the P-tag.

- Changes the P-tag to the expected value (which can be zero) when the peer PE requires the ingress to modify the P-tag. Then, the PE adds a PW label and an outer tag into the packet before forwarding it.

¡ If traffic from the AC does not have the P-tag, the PE performs one of the following operations:

- Adds a P-tag of 0 when the peer PE does not require the ingress to modify the P-tag.

- Adds the expected P-tag (which can be zero) when the peer PE requires the ingress to modify the P-tag. Then, the PE adds a PW label and an outer tag into the packet before forwarding it.

· For traffic received from the PW:

¡ If the AC access mode is VLAN, the PE modifies or keeps the P-tag and forwards the traffic through the AC.

¡ If the AC access mode is Ethernet, the PE removes the P-tag and forwards the traffic through the AC.

Use the force-for-vpls keyword only when you establish BGP PWs between Comware 7 devices and Comware 5 devices.

To ensure successful negotiation of the encapsulation type during VPLS BGP PW establishment between a Comware 7 device and a Comware 5 device, perform the following tasks:

· Configure the same encapsulation type on the devices.

· Specify the force-for-vpls keyword on the Comware 7 device if the Comware 5 device uses the Ethernet or VLAN encapsulation type.

To ensure successful PW establishment, configure the same encapsulation type for all devices in a VPLS instance.

Examples

# Configure the PW data encapsulation type as Ethernet.

<Sysname> system-view

[Sysname] pw-class pw100

[Sysname-pw-pw100] pw-type ethernet

Related commands

display l2vpn pw-class

reset l2vpn mac-address

Use reset l2vpn mac-address to clear MAC address entries for VSIs.

Syntax

reset l2vpn mac-address [ vsi vsi-name ]

Views

User view

Predefined user roles

network-admin

Parameters

vsi vsi-name: Specifies a VSI by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VSI, this command clears MAC address entries for all VSIs.

Usage guidelines

When a VSI learns wrong MAC addresses or has learned the maximum number of MAC addresses, use this command to clear MAC addresses for the VSI. Then, the VSI can learn MAC addresses again.

Examples

# Clear MAC address entries for VSI vpn1.

<Sysname> reset l2vpn mac-address vsi vpn1

Related commands

display l2vpn mac-address vsi

revertive

Use revertive to specify the switchover mode and set the switchover wait time.

Use undo revertive to restore the default.

Syntax

revertive { wtr wtr-time | never }

undo revertive { wtr | never }

Default

The switchover mode is revertive and the switchover wait time is 0 seconds. When the primary PW recovers, traffic is immediately switched back from the backup PW to the primary PW.

Views

VSI LDP signaling view

VSI static configuration view

Predefined user roles

network-admin

Parameters

wtr wtr-time: Specifies the switchover mode as revertive and specifies the wait time in the range of 0 to 3600 seconds. When the primary PW recovers, the PE waits for the specified time before switching traffic from the backup PW to the primary PW.

never: Specifies the switchover mode as non-revertive. After the primary PW recovers, traffic is not switched from the backup PW to the primary PW.

Examples

# Specify the revertive mode and set the switchover wait time to 120 seconds for static PWs in VSI vpn1.

<Sysname> system-view

[Sysname] vsi vpn1

[Sysname-vsi-vpn1] pwsignaling static

[Sysname-vsi-vpn1-static] revertive wtr 120

Related commands

display l2vpn pw

route-distinguisher

Use route-distinguisher to configure a route distinguisher (RD) for an auto-discovery VSI.

Use undo route-distinguisher to restore the default.

Syntax

route-distinguisher route-distinguisher

undo route-distinguisher

Default

No RD is configured for an auto-discovery VSI.

Views

Auto-discovery VSI view

Predefined user roles

network-admin

Parameters

route-distinguisher: Specifies an RD, a string of 3 to 21 characters. An RD can be in one of the following formats:

· 16-bit AS number:32-bit user-defined number. For example, 101:3.

· 32-bit IP address:16-bit user-defined number. For example, 192.168.122.15:1.

· 32-bit AS number:16-bit user-defined number, where the AS number must be equal to or greater than 65536. For example, 65536:1.

Usage guidelines

VPLS uses RDs to differentiate the sites with the same site ID but in different VPNs.

BGP adds the configured RD before the site ID. The RD and the site ID uniquely identify a VPN site.

The configured RD applies to both BGP neighbor auto-discovery and VPLS label block advertisement.

You cannot configure the same RD for different BGP VSIs.

To modify an RD, execute the undo route-distinguisher command to remove the RD and then execute the route-distinguisher command.

Examples

# Configure RD 22:1 for BGP VSI aaa.

<Sysname> system-view

[Sysname] vsi aaa

[Sysname-vsi-aaa] auto-discovery bgp

[Sysname-vsi-aaa-auto] route-distinguisher 22:1

shutdown

Use shutdown to disable a VSI.

Use undo shutdown to enable a VSI.

Syntax

shutdown

undo shutdown

Default

A VSI is enabled.

Views

VSI view

Predefined user roles

network-admin

Usage guidelines

After you disable a VSI, the VSI cannot provide VPLS services.

Use the shutdown command when you want to temporarily disable VPLS. When a VSI is disabled, you can still configure the VSI. After the configuration, use the undo shutdown command to enable the VSI. The VSI will provide VPLS services using the new settings.

Examples

# Disable VSI vpn1.

<Sysname> system-view

[Sysname] vsi vpn1

[Sysname-vsi-vpn1] shutdown

Related commands

display l2vpn vsi

signaling-protocol

Use signaling-protocol to specify a signaling protocol and enter the specified signaling view. The specified signaling protocol is used to establish PWs to the automatically discovered remote PEs.

Use undo signaling-protocol to restore the default.

Syntax

signaling-protocol { bgp | ldp }

undo signaling-protocol

Default

No signaling protocol is specified.

Views

Auto-discovery VSI view

Predefined user roles

network-admin

Parameters

bgp: Specifies the signaling protocol as BGP and enters auto-discovery VSI BGP signaling view.

ldp: Specifies the signaling protocol as LDP and enters auto-discovery VSI LDP signaling view.

Usage guidelines

You can specify only one signaling protocol in the same auto-discovery VSI view. To modify the signaling protocol, execute the undo signaling-protocol command to remove the signaling protocol and then execute the signaling-protocol command.

Examples

# Use LDP (FEC 129) to establish a PW to a remote PE discovered by BGP and enter auto-discovery VSI LDP signaling view.

<Sysname> system-view

[Sysname] vsi aaa

[Sysname-vsi-aaa] auto-discovery bgp

[Sysname-vsi-aaa-auto] signaling-protocol ldp

[Sysname-vsi-aaa-auto-ldp]

Related commands

display l2vpn pw

display l2vpn vsi

site

Use site to create a local site.

Use undo site to delete the local site.

Syntax

site site-id [ range range-value ] [ default-offset default-offset ]

undo site

Default

No sites exist.

Views

Auto-discovery VSI BGP signaling view

Predefined user roles

network-admin

Parameters

site-id: Specifies a local site ID. The value range for this argument is 0 to 120.

range range-value: Specifies the maximum number of sites in a VPLS instance, in the range of 2 to 1 + the maximum number of site-id. The default value is 10.

default-offset default-offset: Specifies the start site ID, 0 or 1. The default value is 0.

Usage guidelines

You can use the site command to increase the range value for an existing site. You cannot decrease the range value for an existing site with the site command. To decrease the range value, execute the undo site command to delete the site and then execute the site command.

You cannot modify the default-offset for a site with the site command. To modify it, execute the undo site command to delete the site and then execute the site command.

Examples

# Create site 1, configure the VPLS instance to contain a maximum of 30 sites, and set the start site ID to 0 for VSI aaa.

<Sysname> system-view

[Sysname] vsi aaa

[Sysname-vsi-aaa] auto-discovery bgp

[Sysname-vsi-aaa-auto] signaling-protocol bgp

[Sysname-vsi-aaa-auto-bgp] site 1 range 30 default-offset 0

Related commands

display l2vpn pw

display l2vpn vsi

snmp-agent trap enable l2vpn

Use snmp-agent trap enable l2vpn to enable SNMP notifications for L2VPN PW.

Use undo snmp-agent trap enable l2vpn to disable SNMP notifications for L2VPN PW.

Syntax

snmp-agent trap enable l2vpn [ pw-delete | pw-switch | pw-up-down ] *

undo snmp-agent trap enable l2vpn [ pw-delete | pw-switch | pw-up-down ] *

Default

SNMP notifications for L2VPN PW are disabled.

Views

System view

Predefined user roles

network-admin

Parameters

pw-delete: Enables PW deletion notifications.

pw-switch: Enables PW primary/backup switchover notifications.

pw-up-down: Enables PW up-down notifications.

Usage guidelines

This feature enables L2VPN to generate SNMP notifications when PW deletions, PW status changes, or PW switchovers occur. For L2VPN event notifications to be sent correctly, you must also configure SNMP on the device. For more information about SNMP configuration, see Network Management and Monitoring Configuration Guide.

If you do not specify a notification type, this command enables all types of notifications for L2VPN PW.

Examples

# Enable PW up-down SNMP notifications.

<Sysname> system-view

[Sysname] snmp-agent trap enable l2vpn pw-up-down

Related commands

display snmp-agent trap-list (Network Management and Monitoring Command Reference)

tunnel-policy (auto-discovery VSI view)

Use tunnel-policy to specify a tunnel policy for an auto-discovery VSI.

Use undo tunnel-policy to restore the default.

Syntax

tunnel-policy tunnel-policy-name

undo tunnel-policy

Default

No tunnel policy is specified.

Views

Auto-discovery VSI view

Predefined user roles

network-admin

Parameters

tunnel-policy-name: Specifies a tunnel policy by its name, a case-sensitive string of 1 to 19 characters.

Usage guidelines

The PWs on the auto-discovery VSI use the specified tunnel policy to select public tunnels.

If you do not specify a tunnel policy or specify a nonexistent tunnel policy, the default tunnel policy applies. The default tunnel policy selects only one public tunnel for a PW in this order: LSP tunnel, GRE tunnel, CRLSP tunnel, and SRLSP tunnel.

Examples

# Specify tunnel policy policy1 for auto-discovery VSI aaa.

<Sysname> system-view

[Sysname] tunnel-policy policy1

[Sysname-tunnel-policy-policy1] quit

[Sysname] vsi aaa

[Sysname-vsi-aaa] auto-discovery bgp

[Sysname-vsi-aaa-auto] tunnel-policy policy1

Related commands

tunnel-policy (system view)

vpls-id

Use vpls-id to set the VPLS ID for a VSI.

Use undo vpls-id to restore the default.

Syntax

vpls-id vpls-id

undo vpls-id

Default

No VPLS ID is specified for a VSI.

Views

Auto-discovery VSI LDP signaling view

Predefined user roles

network-admin

Parameters

vpls-id: Specifies a VPLS ID, a string of 3 to 21 characters. You can specify a VPLS ID in one of the following formats:

· 16-bit AS number:32-bit user-defined number. For example, 101:3.

· 32-bit IP address:16-bit user-defined number. For example, 192.168.122.15:1.

· 32-bit AS number:16-bit user-defined number, where the AS number must be equal to or greater than 65536. For example, 65536:1.

Usage guidelines

A VPLS ID uniquely identifies a VPLS instance. Two PEs must have the same VPLS ID to establish a PW.

VPLS IDs are used in the scenarios where BGP is used to find remote PEs and where FEC 129 LDP is used to establish PWs to the remote PEs.

The local PE advertises a BGP update that includes the configured VPLS ID as an extended community attribute to the remote PE. The remote PE compares the received VPLS ID with its own VPLS ID. If the two VPLS IDs are identical, the two PEs use FEC 129 LDP to establish a PW. If not, the PEs do not establish a PW.

To change a VPLS ID, execute the undo vpls-id command to remove the VPLS ID and then execute the vpls-id command.

Examples

# Configure the VPLS ID 100:1 for VSI aaa.

<Sysname> system-view

[Sysname] vsi aaa

[Sysname-vsi-aaa] auto-discovery bgp

[Sysname-vsi-aaa-auto] signaling-protocol ldp

[Sysname-vsi-aaa-auto-ldp] vpls-id 100:1

Related commands

display l2vpn pw

display l2vpn vsi

vpn-target

Use vpn-target to configure route targets for an auto-discovery VSI.

Use undo vpn-target to remove route targets for an auto-discovery VSI.

Syntax

vpn-target vpn-target&<1-8> [ both | export-extcommunity | import-extcommunity ]

undo vpn-target { vpn-target&<1-8> | all } [ both | export-extcommunity | import-extcommunity ]

Default

No route targets are configured for an auto-discovery VSI.

Views

Auto-discovery VSI view

Predefined user roles

network-admin

Parameters

vpn-target&<1-8>: Specifies a space-separated list of a maximum of eight route targets.

A route target is a string of 3 to 21 characters in one of the following formats:

· 16-bit AS number:32-bit user-defined number. For example, 101:3.

· 32-bit IP address:16-bit user-defined number. For example, 192.168.122.15:1.

· 32-bit AS number:16-bit user-defined number, where the AS number must be equal to or greater than 65536. For example, 65536:1.

both: Uses the specified route targets as both import targets and export targets. The both keyword is used when you do not specify any of both, export-extcommunity, and import-extcommunity.

export-extcommunity: Uses the specified route targets as export targets.

import-extcommunity: Uses the specified route targets as import targets.

all: Removes all route targets.

Usage guidelines

A local PE sets the route targets as export targets in BGP update messages when it advertises L2VPN information through the update messages to a remote peer. The peer uses its import targets to match the received export targets. If a match is found, the peer accepts the L2VPN information.

You can repeat the vpn-target command to configure multiple route targets for an auto-discovery VSI.

Examples

# Configure import route targets as 10:1 100:1 1000:1 and export route targets as 20:1 200:1 2000:1 for auto-discovery VSI aaa.

<Sysname> system-view

[Sysname] vsi aaa

[Sysname-vsi-aaa] auto-discovery bgp

[Sysname-vsi-aaa-auto] vpn-target 10:1 100:1 1000:1 import-extcommunity

[Sysname-vsi-aaa-auto] vpn-target 20:1 200:1 2000:1 export-extcommunity

vsi

Use vsi to create a VSI and enter its view, or enter the view of an existing VSI.

Use undo vsi to delete a VSI.

Syntax

vsi vsi-name

undo vsi vsi-name

Default

No VSIs exist.

Views

System view

Predefined user roles

network-admin

Parameters

vsi-name: Specifies a name for the VSI, a case-sensitive string of 1 to 31 characters.

Usage guidelines

You can create multiple PWs for a VSI manually, or by using LDP or BGP.

Examples

# Create a VSI named vpls1 and enter VSI view.

<Sysname> system-view

[Sysname] vsi vpls1

[Sysname-vsi-vpls1]

Related commands

display l2vpn vsi

xconnect vsi

Use xconnect vsi to bind a Layer 3 interface to a VSI.

Use undo xconnect vsi to restore the default.

Syntax

xconnect vsi vsi-name [ access-mode { ethernet | vlan } ]

undo xconnect vsi

Default

An interface is not bound to any VSI.

Views

Layer 3 interface view

Predefined user roles

network-admin

Parameters

vsi-name: Specifies the name of a VSI, a case-sensitive string of 1 to 31 characters.

access-mode: Specifies the AC access mode.

· When the AC is a VLAN interface or a Layer 3 subinterface, the default access mode is VLAN.

· When the AC is a non-VLAN Layer 3 interface, the default access mode is Ethernet.

ethernet: Specifies the access mode as Ethernet.

vlan: Specifies the access mode as VLAN.

Usage guidelines

After you bind a Layer 3 interface to a VSI, packets received from the interface are forwarded according to the MAC address table of the VSI.

Table 26 shows the description and usage guidelines for the parameters in this command.

Table 26 Description and usage guidelines for command parameter

Parameter	Usage guidelines
access-mode { ethernet \| vlan }	The AC access mode determines how the device (PE) considers the VLAN tag in Ethernet frames received from the CE and how the PE forwards Ethernet frames to the CE. · VLAN access mode—Ethernet frames received from the CE must carry a VLAN tag in the Ethernet header. The PE considers the VLAN tag as a P-tag assigned by the service provider. Ethernet frames sent to the CE must also carry the P-tag. · Ethernet access mode—If Ethernet frames from the CE have a VLAN tag in the header, the PE considers it as a U-tag and ignores it. Ethernet frames sent to the CE do not carry the P-tag.

Parameter

Usage guidelines

access-mode { ethernet | vlan }

The AC access mode determines how the device (PE) considers the VLAN tag in Ethernet frames received from the CE and how the PE forwards Ethernet frames to the CE.

· VLAN access mode—Ethernet frames received from the CE must carry a VLAN tag in the Ethernet header. The PE considers the VLAN tag as a P-tag assigned by the service provider. Ethernet frames sent to the CE must also carry the P-tag.

· Ethernet access mode—If Ethernet frames from the CE have a VLAN tag in the header, the PE considers it as a U-tag and ignores it. Ethernet frames sent to the CE do not carry the P-tag.

‌

Examples

# Bind Ten-GigabitEthernet 0/0/6 to VSI vpn1.

<Sysname> system-view

[Sysname] vsi vpn1

[Sysname-vsi-vpn1] quit

[Sysname] interface ten-gigabitethernet 0/0/6

[Sysname-Ten-GigabitEthernet0/0/6] xconnect vsi vpn1

Related commands

display l2vpn interface

vsi

11-MPLS Command Reference

VPLS commands

control-word enable

display bgp l2vpn auto-discovery

display bgp l2vpn signaling

display l2vpn mac-address

display l2vpn vsi

l2vpn switchover

pw-class (auto-discovery VSI view)

revertive

tunnel-policy (auto-discovery VSI view)

Intelligent Terminal Products

Product Support Services

Technical Service Solutions

Resource Center

Policy

Online Help

Become a Partner

Partner Policy & Program

Global Learning

Partner Sales Resources

Service Business

News & Events

Contact Us