Rule matching acceleration enhances connection establishment and packet forwarding performance, especially for a device using multiple rules to match packets from multiple users.

Rule matching acceleration does not take effect on newly added, modified, and moved rules unless the feature is activated for the rules. By default, the system automatically activates rule matching acceleration for such rules at specific intervals. The interval is 2 seconds if 100 or fewer rules exist and 20 seconds if over 100 rules exist.

To activate rule matching acceleration immediately after a rule change, you can execute this command.

If no rule change is detected, the system does not perform an activation operation.

Insufficient memory can cause rule matching acceleration failures. Unaccelerated rules do not take effect, and rules that have been accelerated are not affected.

Examples

# Activate rule matching acceleration.

<Sysname> system-view

[Sysname] security-policy ip

[Sysname-security-policy-ip] accelerate enhanced enable

action

Use action to set the action for a security policy rule.

Syntax

action { drop | pass }

Default

The action for a security policy rule is drop.

Views

Security policy rule view

Predefined user roles

network-admin

Parameters

drop: Discards matched packets.

pass: Allows matched packets to pass.

Usage guidelines

If you execute this command multiple times, the most recent configuration takes effect.

Examples

# Set the action for security policy rule rule1 to drop.

<Sysname> system-view

[Sysname] security-policy ip

[Sysname-security-policy-ip] rule 0 name rule1

[Sysname-security-policy-ip-0-rule1] action drop

Related commands

display security-policy

app-group

Use app-group to specify an application group as a filtering criterion of a security policy rule.

Use undo app-group to remove the specified application group filtering criterion from a security policy rule.

Syntax

app-group app-group-name

undo app-group [ app-group-name ]

Default

No application group is specified as a filtering criterion for a security policy rule.

Views

Security policy rule view

Predefined user roles

network-admin

Parameters

app-group-name: Specifies the name of an application policy, a case-insensitive string of 1 to 63 characters. The name cannot be invalid or other. If you do not specify this argument when executing the undo app-group command, the command removes all application groups from the rule. For more information about application groups, see APR in Security Configuration Guide.

Usage guidelines

You can execute the command multiple times to specify multiple application groups as the filtering criteria.

Examples

# Specify application groups app1 and app2 as the filtering criteria of security policy rule rule1.

<Sysname> system-view

[Sysname] security-policy ip

[Sysname-security-policy-ip] rule 0 name rule1

[Sysname-security-policy-ip-0-rule1] app-group app1

[Sysname-security-policy-ip-0-rule1] app-group app2

Related commands

app-group

display security-policy

application

Use application to specify an application as a filtering criterion of a security policy rule.

Use undo application to remove the specified application filtering criterion from a security policy rule.

Syntax

application application-name

undo application [ application-name ]

Default

No application is specified as a filtering criterion for a security policy rule.

Views

Security policy rule view

Predefined user roles

network-admin

Parameters

application-name: Specifies the name of an application, a case-insensitive string of 1 to 63 characters. The name cannot be invalid or other. If you do not specify this argument when executing the undo application command, the command removes all applications from the rule. For more information about applications, see APR in Security Configuration Guide.

Usage guidelines

You can execute the command multiple times to specify multiple applications as the filtering criteria.

For the application filtering criteria to be identified, you must permit the packets of the protocols on which the applications depend to pass through. If port-based packet filtering is configured and a dependent protocol uses a non-default port, you must permit the packets from the port to pass.

Examples

# Specify applications 139Mail and 51job as the filtering criteria of security policy rule rule1.

<Sysname> system-view

[Sysname] security-policy ip

[Sysname-security-policy-ip] rule 0 name rule1

[Sysname-security-policy-ip-0-rule1] application 139Mail

[Sysname-security-policy-ip-0-rule1] application 51job

Related commands

display security-policy

nbar application

port-mapping

counting enable

Use counting enable to enable statistics collection for matched packets.

Use undo counting enable to disable statistics collection for matched packets.

Syntax

counting enable

undo counting enable

Default

Statistics collection for matched packets is disabled.

Views

Security policy rule view

Predefined user roles

network-admin

Usage guidelines

This feature enables the device to collect statistics about matched packets. The collected statistics can be viewed by executing the display security-policy statistics command.

Examples

# Enable matched packet statistics collection for security policy rule rule1.

<Sysname> system-view

[Sysname] security-policy ip

[Sysname-security-policy-ip] rule 0 name rule1

[Sysname-security-policy-ip-0-rule1] counting enable

Related commands

display security-policy

display security-policy statistics

default rule action

Use default rule action to configure the action of the default security policy rule.

Syntax

default rule action { drop | pass }

Default

The action for the default security policy rule is drop.

Views

Security policy view

Predefined user roles

network-admin

Parameters

drop: Discards matched packets.

pass: Allows matched packets to pass.

Usage guidelines

If you execute this command multiple times, the most recent configuration takes effect.

Examples

# Set the action for the default security policy rule to drop.

<Sysname> system-view

[Sysname] security-policy ip

[Sysname-security-policy-ip] default rule action drop

default rule counting enable

Use default rule counting enable to enable statistics collection for the default security policy rule.

Use undo default rule counting enable to disable statistics collection for the default security policy rule.

Syntax

default rule counting enable

undo default rule counting enable

Default

Statistics collection is disabled for the default security policy rule.

Views

Security policy view

Predefined user roles

network-admin

Usage guidelines

This feature enables the device to collect statistics about packets matching the default security policy rule. To view the collected statistics, execute the display security-policy statistics command.

Examples

# Enable matched packet statistics collection for the default security policy rule.

<Sysname> system-view

[Sysname] security-policy ip

[Sysname-security-policy-ip] default rule counting enable

default rule logging enable

Use default rule logging enable to enable logging for the default security policy rule.

Use undo default rule logging enable to disable logging for the default security policy rule.

Syntax

default rule logging enable

undo default rule logging enable

Default

Logging for is disabled for the default security policy rule.

Views

Security policy view

Predefined user roles

network-admin

Usage guidelines

This feature enables the security policy module to generate log messages for packet matching events of the default security policy rule and send the messages to the information center.

With the information center, you can set log message filtering and output rules, including output destinations.

The information center can output packet matching logs to any destinations except the console and the monitor terminal. If you configure the console or monitor terminal as an output destination, the output destination setting will not take effect.

To view packet matching logs stored on the device, use the display logbuffer command or open the security policy log page from the Web interface of the device. Make sure you do not disable log output to the log buffer, which is enabled by default.

For more information about configuring the information center, see System Management Configuration Guide.

Examples

# Enable matched packet logging for the default security policy rule.

<Sysname> system-view

[Sysname] security-policy ip

[Sysname-security-policy-ip] default rule logging enable

description (security policy rule view)

Use description to configure a description for a security policy rule.

Use undo description to restore the default.

Syntax

description text

undo description

Default

No description is configured for a security policy rule.

Views

Security policy rule view

Predefined user roles

network-admin

Parameters

text: Specifies a description, a case-sensitive string of 1 to 127 characters.

Examples

# Configure the description as This rule is used for source-ip ip1 for security policy rule rule1.

<Sysname> system-view

[Sysname] security-policy ip

[Sysname-security-policy-ip] rule 0 name rule1

[Sysname-security-policy-ip-0-rule1] description This rule is used for source-ip ip1

Related commands

display object-policy ip

display object-policy ipv6

description (security policy view)

Use description to configure a description for the IPv4 or IPv6 security policy.

Use undo description to restore the default.

Syntax

description text

undo description

Default

No description is configured for the IPv4 or IPv6 security policy.

Views

IPv4 security policy view

IPv6 security policy view

Predefined user roles

network-admin

Parameters

text: Specifies a description, a case-sensitive string of 1 to 127 characters.

Examples

# Configure the description as zone-pair security office to library for the IPv4 security policy.

<Sysname> system-view

[Sysname] security-policy ip

[Sysname-security-policy-ip] description zone-pair security office to library

Related commands

display security-policy

destination-ip

Use destination-ip to specify a destination IP address object group as a filtering criterion of a security policy rule.

Use undo destination-ip to remove the specified destination IP address object group from a security policy rule.

Syntax

destination-ip object-group-name

undo destination-ip [ object-group-name ]

Default

No destination IP address object group is specified as a filtering criterion for a security policy rule.

Views

Security policy rule view

Predefined user roles

network-admin

Parameters

object-group-name: Specifies the name of a destination IP address object group, a case-insensitive string of 1 to 31 characters. The name cannot be any. If you do not specify this argument when executing the undo destination-ip command, the command removes all destination IP address object groups from the rule. For more information about object groups, see Security Configuration Guide.

Usage guidelines

You can execute the command multiple times to specify multiple destination IP address object groups as the filtering criteria.

If you specify a nonexistent object group, the device automatically creates the specified object group with empty configuration. A rule that contains an object group with empty configuration does not match any packets.

Examples

# Specify destination IP address object groups client1 and client2 as the filtering criteria of security policy rule rule1.

<Sysname> system-view

[Sysname] security-policy ip

[Sysname-security-policy-ip] rule 0 name rule1

[Sysname-security-policy-ip-0-rule1] destination-ip client1

[Sysname-security-policy-ip-0-rule1] destination-ip client2

Related commands

display security-policy

object-group

destination-zone

Use destination-zone to specify a destination security zone as a filtering criterion of a security policy rule.

Use undo destination-zone to remove the specified destination security zone from a security policy rule.

Syntax

destination-zone destination-zone-name

undo destination-zone [ destination-zone-name ]

Default

No destination security zone is specified as a filtering criterion for a security policy rule.

Views

Security policy rule view

Predefined user roles

network-admin

Parameters

object-group-name: Specifies the name of a destination security zone, a case-insensitive string of 1 to 31 characters. If you do not specify this argument when executing the undo destination-zone command, the command removes all destination security zones from the rule. For more information about security zones, see Security Configuration Guide.

Usage guidelines

You can execute the command multiple times to specify multiple destination security zones as the filtering criteria.

Examples

# Specify destination security zones trust and server as the filtering criteria of security policy rule rule1.

<Sysname> system-view

[Sysname] security-policy ip

[Sysname-security-policy-ip] rule 0 name rule1

[Sysname-security-policy-ip-0-rule1] destination-zone trust

[Sysname-security-policy-ip-0-rule1] destination-zone server

Related commands

display security-policy

security-zone

disable

Use disable to disable a security policy rule.

Use undo disable to enable a security policy rule.

Syntax

disable

undo disable

Default

A security policy rule is disabled.

Views

Security policy rule view

Predefined user roles

network-admin

Examples

# Disable security policy rule rule1.

<Sysname> system-view

[Sysname] security-policy ip

[Sysname-security-policy-ip] rule 0 name rule1

[Sysname-security-policy-ip-0-rule1] disable

Related commands

display security-policy

Use display security-policy to display information about the specified security policy.

Syntax

display security-policy { ip | ipv6 }

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

ip: Specifies the IPv4 security policy.

ipv6: Specifies the IPv6 security policy.

Examples

# Display information about the IPv4 security policy.

<Sysname> display security-policy ip

Security-policy ip

rule 0 name der (Inactive)

action pass

profile er

vrf re

logging enable

counting enable

counting enable TTL 1200

time-range dere

track positive 23

session aging-time 5000

session persistent aging-time 2400

source-zone trust

destination-zone trust

source-ip erer

destination-ip client1

service ftp

app-group ere

application 110Wang

user der

user-group ere

undo disable

Table 1 Command output

Field	Description
rule id name rule-name	Rule ID and rule name.
action pass	Rule action: · pass—Allows matched packets to pass. · drop—Drops matched packets.
profile app-profile-name	DPI application profile applied to the rule.
vrf vrf-name	MPLS L3VPN instance whose packets can be filtered by the rule.
logging enable	Indicates that logging for matched packets is enabled.
counting enable	Indicates that statistics collection for matched packets is enabled.
counting enable TTL time-value	Indicates that statistics collection for matched packets is enabled. The time-value argument represents the remaining enabling period in seconds.
time-range time-range-name	Time range during which the rule is in effect.
track negative 1 (Active)	Track entry and track entry state associated with the security policy rule.
session aging-time time-value	Session aging time.
session persistent aging-time time-value	Persistent session aging time.
source-zone zone-name	Source security zone that acts as a filtering criterion.
destination-zone zone-name	Destination security zone that acts as a filtering criterion.
source-ip object-group-name	Source IP address object group that acts as a filtering criterion.
destination-ip object-group-name	Destination IP address object group that acts as a filtering criterion.
service object-group-name	Service object group that acts as a filtering criterion.
app-group app-group-name	Application group that acts as a filtering criterion.
application application-name	Application that acts as a filtering criterion.
user user-name	User that acts as a filtering criterion.
user-group user-group-name	User group that acts as a filtering criterion.
undo disable	The rule is enabled.

Related commands

security-policy ip

security-policy ipv6

display security-policy statistics

Use display security-policy statistics to display security policy statistics.

Syntax

display security-policy statistics { ip | ipv6 } [ rule rule-name ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

ip: Specifies the IPv4 security policy.

ipv6: Specifies the IPv6 security policy.

rule rule-name: Specifies a security policy rule by its name, a case-insensitive string of 1 to 127 characters. If you do not specify this option, the command displays statistics about all security policy rules of the specified IP version.

Examples

# Display statistics about IPv4 security policy rule abc.

<Sysname> display security-policy statistics ip rule abc

rule 0 name abc

action: pass (5 packets, 1000 bytes)

Table 2 Command output

Field	Description
rule id name rule-name	Rule ID and rule name.
action	Rule action: · pass—Allows matched packets to pass. · drop—Drops matched packets.
x packets, y bytes	The rule has matched x packets, a total of y bytes. This field is displayed only if the counting enable or the logging enable command has been executed for the rule.

Related commands

reset security-policy statistics

group move

Use group move to move a security policy rule group to change the match order of security policy rules.

Syntax

group move group-name1 { after | before } { group group-name2 | rule rule-name }

Views

Security policy view

Predefined user roles

network-admin

Parameters

group-name1: Specifies the name of the security policy rule group to be moved, a case-insensitive string of 1 to 63 characters.

after: Moves the security policy rule group to the place after the target security policy rule group or the target security policy rule.

before: Moves the security policy rule group to the place before the target security policy rule group or the target security policy rule.

group group-name2: Specifies the name of the target security policy rule group, a case-insensitive string of 1 to 63 characters.

rule rule-name: Specifies the name of the target security policy rule, a case-insensitive string of 1 to 127 characters.

Usage guidelines

If you specify a target security policy rule that belongs to a security policy rule group, follow these restrictions and guidelines:

· If the target rule is neither the start nor end rule of the group, you cannot move a security policy rule group to the place before or after the rule.

· If the target rule is the start rule of the group, you can only move a security policy rule group to the place before the rule.

· If the target rule is the end rule of the group, you can only move a security policy rule group to the place after the rule.

Examples

# Move security policy rule group group1 to the place before security policy rule group group2.

<Sysname> system-view

[Sysname] security-policy ip

[Sysname-security-policy-ip] group move group1 before group group2

group name

Use group name to create a security policy rule group and add security policy rules to the group, or add security policy rules to an existing security policy rule group.

Use undo group name to delete a security policy rule group.

Syntax

group name group-name [ from rule-name1 to rule-name2 ] [ description description-text ] [ disable | enable ]

undo group name group-name [ description | include-member ]

Default

No security policy rule group exists.

Views

Security policy view

Predefined user roles

network-admin

Parameters

group-name: Specifies a security policy rule group name, a case-insensitive string of 1 to 63 characters.

from rule-name1: Specifies the start rule of a rule list. The rule-name1 argument represents the security policy rule name, a case-insensitive string of 1 to 127 characters.

to rule-name2: Specifies the end rule of the rule list. The rule-name2 argument represents the security policy rule name, a case-insensitive string of 1 to 127 characters.

description description-text: Specifies the security policy description, a case-sensitive string of 1 to 127 characters. By default, no description is specified for a security policy rule group.

disable: Disables the security policy rule group.

enable: Enables the security policy rule group. By default, a security policy rule group is enabled.

include-member: Specifies security policy rules in the security policy rule group.

Usage guidelines

Security policy rule grouping allows users to enable, disable, delete, and move security policy rules in batches.

A security policy rule in a security policy rule group takes effect only when both the rule and the group are enabled.

To add a list of security policy rules, make sure the end rule is listed behind the start rule and the specified rules do not belong to any other security policy rule group.

When you execute the undo command, follow these restrictions and guidelines:

· The undo group name group-name command deletes only the specified security policy rule group.

· The undo group name group-name description command deletes only the description for the specified security policy rule group.

· The undo group name group-name include-member command deletes both the specified security policy rule group and all the security policy rules in the group.

Examples

# Create security policy rule group group1, add security policy rules rule-name1 through rule-name10 to the group, and specify the group description as marketing.

<Sysname> system-view

[Sysname] security-policy ip

[Sysname-security-policy-ip] group name group1 from rule-name1 to rule-name10 enable description marketing

group rename

Use group rename to rename a security policy rule group.

Syntax

group rename old-name new-name

Views

Security policy view

Predefined user roles

network-admin

Parameters

old-name: Specifies the name of a security policy rule group, a case-insensitive string of 1 to 63 characters.

new-name: Specifies a new name for the security policy rule group, a case-insensitive string of 1 to 63 characters.

Examples

# Rename security policy rule group group1 to group2.

<Sysname> system-view

[Sysname] security-policy ip

[Sysname-security-policy-ip] group rename group1 group2

logging enable

Use logging enable to enable logging for matched packets.

Use undo logging enable to disable logging for matched packets.

Syntax

logging enable

undo logging enable

Default

Logging for matched packets is disabled.

Views

Security policy rule view

Predefined user roles

network-admin

Usage guidelines

This feature enables the security policy module to send log messages to the information center when packets match a security policy.

With the information center, you can set log message filtering and output rules, including output destinations.

For more information about configuring the information center, see System Management Configuration Guide.

Examples

# Enable matched packet logging for security policy rule rule1.

<Sysname> system-view

[Sysname] security-policy ip

[Sysname-security-policy-ip] rule 0 name rule1

[Sysname-security-policy-ip-0-rule1] logging enable

Related commands

display security-policy

move rule

Use move rule to move a security policy rule by rule ID.

Syntax

move rule rule-id before insert-rule-id

Views

IPv4 security policy view

IPv6 security policy view

Predefined user roles

network-admin

Parameters

rule-id: Specifies the ID of a rule, in the range of 0 to 65534.

insert-rule-id: Specifies the ID of the target rule before which a rule is inserted. The target rule ID is in the range of 0 to 65535. If you specify 65535 as the target rule ID, the rule is moved to the end of the list.

Usage guidelines

The system does not execute the command in the following situations:

· You specify the same value for the rule-id and insert-rule-id arguments.

· You specify a nonexistent rule.

Examples

# Insert rule 5 before rule 2 for the IPv4 security policy.

<Sysname> system-view

[Sysname] security-policy ip

[Sysname-security-policy-ip] move rule 5 before 2

Related commands

rule

security-policy ip

security-policy ipv6

parent-group

Use parent-group to specify a security policy rule group for a security policy rule.

Use undo parent-group to restore the default.

Syntax

parent-group group-name

undo parent-group

Default

A security policy rule does not belong to any security policy rule group.

Views

Security policy rule view

Predefined user roles

network-admin

Parameters

group-name: Specifies the name of a security policy rule group, a case-insensitive string of 1 to 63 characters.

Examples

# Assign security policy rule rule1 to security policy rule group group1.

<Sysname> system-view

[Sysname] security-policy ip

[Sysname-security-policy-ip] rule 1 name rule1

[Sysname-security-policy-ip-1-rule1] parent-group group1

profile

Use profile to apply a DPI application profile to a security policy rule.

Use undo profile to remove the DPI application profile applied to a security policy rule.

Syntax

profile app-profile-name

undo profile

Default

No DPI application profile is applied to a security policy rule.

Views

Security policy rule view

Predefined user roles

network-admin

Parameters

app-profile-name: Specifies the name of a DPI application profile, a case-insensitive string of 1 to 63 characters. For more information about DPI application profiles, see DPI engine in DPI Configuration Guide.

Usage guidelines

This feature enables the device to perform DPI on packets matching the specified rule. For more information about DPI, see DPI Configuration Guide.

This feature takes effect only when the rule action is pass.

Examples

# Apply DPI application profile p1 to IPv4 security policy rule rule1.

<Sysname> system-view

[Sysname] security-policy ip

[Sysname-security-policy-ip] rule 0 name rule1

[Sysname-security-policy-ip-0-rule1] action pass

[Sysname-security-policy-ip-0-rule1] profile p1

Related commands

action pass

app-profile (DPI Command Reference)

display security-policy ip

reset security-policy statistics

Use reset security-policy statistics to clear security policy statistics.

Syntax

reset security-policy statistics [ ip | ipv6 ] [ rule rule-name ]

Views

Any view

Predefined user roles

network-admin

Parameters

ip: Specifies the IPv4 security policy.

ipv6: Specifies the IPv6 security policy.

rule rule-name: Specifies a security policy rule by its name, a case-insensitive string of 1 to 127 characters.

Usage guidelines

If you do not specify any keyword or option, the command clears all security policy statistics.

Examples

# Clear the security policy statistics about IPv4 security policy rule abc.

<Sysname> reset security-policy statistics ip rule abc

Related commands

display security-policy statistics

rule

Use rule to create a security policy rule and enter its view, or enter the view of an existing security policy rule.

Use undo rule to delete the specified security policy rule.

Syntax

rule { rule-id | [ rule-id ] name rule-name }

undo rule { rule-id | name rule-name } *

Default

No security policy rules exist.

Views

IPv4 security policy view

IPv6 security policy view

Predefined user roles

network-admin

Parameters

rule-id: Specifies a rule ID in the range of 0 to 65534. If you do not specify an ID for the rule, the system automatically assigns the rule the integer next to the greatest ID being used. If the greatest ID is 65534, the system assigns the rule the smallest unused number in the range.

rule-name: Specifies a globally unique rule name, a case-insensitive string of 1 to 127 characters. The name cannot be default. You must specify a rule name when creating a rule.

Examples

# Create an IPv4 security policy rule with rule ID 0 and rule name rule1.

<Sysname> system-view

[Sysname] security-policy ip

[Sysname-security-policy-ip] rule 0 name rule1

[Sysname-security-policy-ip-0-rule1]

Related commands

display security-policy ip

display security-policy ipv6

security-policy

Use security-policy to enter security policy view.

Use undo security-policy to delete all configurations in security policy view.

Syntax

security-policy { ip | ipv6 }

undo security-policy { ip | ipv6 }

Default

No configurations exist in security policy view.

Views

System view

Predefined user roles

network-admin

Parameters

ip: Specifies the IPv4 security policy.

ipv6: Specifies the IPv6 security policy.

Examples

# Enter IPv4 security policy view.

<Sysname> system-view

[Sysname] security-policy ip

[Sysname-security-policy-ip]

Related commands

display security-policy

security-policy log real-time-sending enable

Use security-policy log real-time-sending enable to enable real-time sending for security policy log messages.

Use undo security-policy log real-time-sending enable to disable real-time sending for security policy log messages.

Syntax

security-policy log real-time-sending enable

undo security-policy log real-time-sending enable

Default

The buffering mode is used to generate and send security policy log messages.

Views

System view

Predefined user roles

network-admin

Usage guidelines

The device can send security policy log messages in the following ways:

· Buffering mode—After the device generates and sends the log message for the first packet of a flow, it buffers that log message and starts a 5-second timer, which is not configurable. If other packets of the same flow match are received before the timer expires, the buffered log message is sent. Otherwise, the buffered log message is deleted. After the number of log messages reaches the limit, no log messages can be generated for subsequent flows.

· Real-time mode—The device generates and sends a log message for the first packet of a flow but does not buffer it. For packets of a flow permitted by a security policy, the device generates and sends only one log message. For packets of a flow denied by a security policy, the device generates and sends one log message for each packet.

Examples

# Enable real-time sending for security policy log messages.

<Sysname>system-view

[Sysname] security-policy log real-time-sending enable

Related commands

logging enable

service

Use service to specify a service object group as a filtering criterion of a security policy rule.

Use undo service to remove the specified service object group from a security policy rule.

Syntax

service { object-group-name | any }

undo service [ object-group-name | any ]

Default

No service object group is specified as a filtering criterion for a security policy rule.

Views

Security policy rule view

Predefined user roles

network-admin

Parameters

object-group-name: Specifies the name of a service object group, a case-insensitive string of 1 to 31 characters.

any: Specifies all service object groups.

Usage guidelines

You can execute the command multiple times to specify multiple service object groups as the filtering criteria.

If you specify neither an object group nor the any keyword when executing the undo service command, the command removes all service object groups from the security policy rule.

Examples

# Specify service object groups http and ftp as the filtering criteria of security policy rule rule1.

<Sysname> system-view

[Sysname] security-policy ip

[Sysname-security-policy-ip] rule 0 name rule1

[Sysname-security-policy-ip-0-rule1] service http

[Sysname-security-policy-ip-0-rule1] service ftp

Related commands

display security-policy

object-group

session aging-time

Use session aging-time to set the session aging time for a security policy rule.

Use undo session aging-time to restore the default.

Syntax

session aging-time time-value

undo session aging-time

Default

The session aging time is not configured for a security policy rule.

Views

Security policy rule view

Predefined user roles

network-admin

Parameters

time-value: Specifies the aging time in the range of 1 to 2000000 seconds.

Usage guidelines

This command sets the aging time for stable sessions created for packets matching the specified security policy rule, and takes effect only on newly created sessions.

If the aging time is not configured for a rule, the stable sessions use the aging time set by using the session aging-time application or the session aging-time state command. For more information about session management, see Security Configuration Guide.

The session aging time for unstable sessions is one hour.

Examples

# Set the session aging time to 5000 seconds for security policy rule rule1.

<Sysname> system-view

[Sysname] security-policy ip

[Sysname-security-policy-ip] rule 0 name rule1

[Sysname-security-policy-ip-0-rule1] action pass

[Sysname-security-policy-ip-0-rule1] session aging-time 5000

Related commands

display security-policy

session aging-time application

session aging-time state

session persistent acl

session persistent aging-time

Use session persistent aging-time to set the aging time for persistent sessions.

Use undo session persistent aging-time to restore the default.

Syntax

session persistent aging-time time-value

undo session persistent aging-time

Default

The persistent session aging time is not configured for a security policy rule.

Views

Security policy rule view

Predefined user roles

network-admin

Parameters

time-value: Specifies the aging time in the range of 0 to 24000 hours. If you set the aging time to 0, persistent sessions do not age out.

Usage guidelines

This command is effective only on TCP sessions in ESTABLISHED state.

It sets the aging time for persistent sessions created for packets matching the specified security policy rule, and takes effect only on newly created sessions.

The aging time configured by using this command takes precedence over the aging times configured by using the session aging-time and session persistent acl commands.

Examples

# Set the persistent session aging time to one hour for security policy rule rule1.

<Sysname> system-view

[Sysname] security-policy ip

[Sysname-security-policy-ip] rule 0 name rule1

[Sysname-security-policy-ip-0-rule1] action pass

[Sysname-security-policy-ip-0-rule1] session persistent aging-time 1

Related commands

display security-policy

session persistent acl

source-ip

Use source-ip to specify a source IP address object group as a filtering criterion of a security policy rule.

Use undo source-ip to remove the specified source IP address object group from a security policy rule.

Syntax

source-ip object-group-name

undo source-ip [ object-group-name ]

Default

No source IP address object group is specified as a filtering criterion for a security policy rule.

Views

Security policy rule view

Predefined user roles

network-admin

Parameters

object-group-name: Specifies the name of a source IP address object group, a case-insensitive string of 1 to 31 characters. The name cannot be any. If you do not specify this argument when executing the undo source-ip command, the command removes all source IP address object groups from the rule. For more information about object groups, see Security Configuration Guide.

Usage guidelines

You can execute the command multiple times to specify multiple source IP address object groups as the filtering criteria.

Examples

# Specify source IP address object groups server1 and server2 as the filtering criteria of security policy rule rule1.

<Sysname> system-view

[Sysname] security-policy ip

[Sysname-security-policy-ip] rule 0 name rule1

[Sysname-security-policy-ip-0-rule1] source-ip server1

[Sysname-security-policy-ip-0-rule1] source-ip server2

Related commands

display security-policy

object-group

source-zone

Use source-zone to specify a source security zone as a filtering criterion of a security policy rule.

Use undo source-zone to remove the specified source security zone from a security policy rule.

Syntax

source-zone source-zone-name

undo source-zone [ source-zone-name ]

Default

No source security zone is specified as a filtering criterion for a security policy rule.

Views

Security policy rule view

Predefined user roles

network-admin

Parameters

source-zone-name: Specifies the name of a source security zone, a case-insensitive string of 1 to 31 characters. If you do not specify this argument when executing the undo source-zone command, the command removes all source security zones from the rule. For more information about security zones, see Security Configuration Guide.

Usage guidelines

You can execute the command multiple times to specify multiple source security zones as the filtering criteria.

Examples

# Specify source security zones trust and dmz as the filtering criteria of security policy rule rule1.

<Sysname> system-view

[Sysname] security-policy ip

[Sysname-security-policy-ip] rule 0 name rule1

[Sysname-security-policy-ip-0-rule1] source-zone trust

[Sysname-security-policy-ip-0-rule1] source-zone dmz

Related commands

display security-policy

security-zone

time-range

Use time-range to specify the time range during which a security policy rule is in effect.

Use undo time-range to restore the default.

Syntax

time-range time-range-name

undo time-range

Default

A security policy rule is in effect at any time.

Views

Security policy rule view

Predefined user roles

network-admin

Parameters

time-range-name: Specifies the name of a time range, a case-insensitive string of 1 to 32 characters. For more information about time ranges, see ACL and QoS Configuration Guide.

Usage guidelines

If you execute this command multiple times, the most recent configuration takes effect.

Examples

# Enable security policy rule rule1 to be in effect during time range work.

<Sysname> system-view

[Sysname] security-policy ip

[Sysname-security-policy-ip] rule 0 name rule1

[Sysname-security-policy-ip-0-rule1] time-range work

Related commands

display security-policy

time-range (ACL and QoS Command Reference)

track

Use track to associate a security policy rule with a track entry.

Use undo track to disassociate a security policy rule from the track entry.

Syntax

track { negative | positive } track-entry-number

undo track

Default

No track entry is associated with a security policy rule.

Views

Security policy rule view

Predefined user roles

network-admin

Parameters

negative: Specifies the Negative state of a track entry.

positive: Specifies the Positive state of a track entry.

track-entry-number: Specifies the number of a track entry, in the range of 1 to 1024. For more information about Track, see High Availability Configuration Guide.

Usage guidelines

Use this command to enable the collaboration between the track module and a security policy rule. The collaboration operates as follows:

· If a rule is associated with the Negative state of a track entry, the device:

¡ Sets the rule state to Active if the track entry is in Negative state.

¡ Sets the rule state to Inactive if the track entry is in Positive state.

· If a rule is associated with the Positive state of a track entry, the device:

¡ Sets the rule state to Active if the track entry is in Positive state.

¡ Sets the rule state to Inactive if the track entry is in Negative state.

If you execute this command multiple times, the most recent configuration takes effect.

Examples

# Associate security policy rule rule1 with the Positive state of track entry 10.

<Sysname> system-view

[Sysname] security-policy ip

[Sysname-security-policy-ip] rule 0 name rule1

[Sysname-security-policy-ip-0-rule1] track positive 10

Related commands

display security-policy

track bfd (High Availability Command Reference)

track interface (High Availability Command Reference)

track ip route reachability (High Availability Command Reference)

track nqa (High Availability Command Reference)

user

Use user to specify a user as a filtering criterion of a security policy rule.

Use undo user to remove the specified user filtering criterion from a security policy rule.

Syntax

user username [ domain domain-name ]

undo user [ username [ domain domain-name ] ]

Default

No user is specified as a filtering criterion for a security policy rule.

Views

Security policy rule view

Predefined user roles

network-admin

Parameters

username: Specifies a username, a case-sensitive string of 1 to 55 characters. The name cannot be a, al, or all and cannot contain at signs (@). If you do not specify this argument when executing the undo user command, the command removes all users from the rule. For more information about users and identity domains, see user identification in User Access and Authentication Configuration Guide.

domain domain-name: Matches the user in an identity domain. The domain-name argument represents the identity domain name, a case-insensitive string of 1 to 255 characters. The string cannot contain forward slashes (/), backslashes (\), vertical bars (|), colons (:), asterisks (*), question marks (?), left angle brackets (<), right angle brackets (>), or at signs (@). If you do not specify this option, the command matches the user among users that do not belong to any identity domain.

Usage guidelines

You can execute the command multiple times to specify multiple users as the filtering criteria.

Examples

# Specify users usera and userb in identity domain test as the filtering criteria of security policy rule rule1.

<Sysname> system-view

[Sysname] security-policy ip

[Sysname-security-policy-ip] rule 0 name rule1

[Sysname-security-policy-ip-0-rule1] user usera domain test

[Sysname-security-policy-ip-0-rule1] user userb domain test

Related commands

display security-policy

user-identity enable

user-identity static-user

user-group

Use user-group to specify a user group as a filtering criterion of a security policy rule.

Use undo user-group to remove the specified user group filtering criterion from a security policy rule.

Syntax

user-group user-group-name [ domain domain-name ]

undo user-group [ user-group-name [ domain domain-name ] ]

Default

No user group is specified as a filtering criterion for a security policy rule.

Views

Security policy rule view

Predefined user roles

network-admin

Parameters

user-group-name: Specifies the name of a user group, a case-insensitive string of 1 to 200 characters. If you do not specify this argument when executing the undo user-group command, the command removes all user groups from the rule. For more information about user groups and identity domains, see user identification in User Access and Authentication Configuration Guide.

domain domain-name: Matches the user group in an identity domain. The domain-name argument represents the identity domain name, a case-insensitive string of 1 to 255 characters. The string cannot contain forward slashes (/), backslashes (\), vertical bars (|), colons (:), asterisks (*), question marks (?), left angle brackets (<), right angle brackets (>), or at signs (@). If you do not specify this option, the command matches the user group among user groups that do not belong to any identity domain.

Usage guidelines

You can execute the command multiple times to specify multiple user groups as the filtering criteria.

Examples

# Specify user groups groupa and groupb in identity domain test as the filtering criteria of security policy rule rule1.

<Sysname> system-view

[Sysname] security-policy ip

[Sysname-security-policy-ip] rule 0 name rule1

[Sysname-security-policy-ip-0-rule1] user-group groupa domain test

[Sysname-security-policy-ip-0-rule1] user-group groupb domain test

Related commands

display security-policy

user-group

vrf

Use vrf to configure a security policy rule to take effect on received packets of the specified MPLS L3VPN instance.

Use undo vrf to restore the default.

Syntax

vrf vrf-name

undo vrf

Default

A security policy rule takes effect on received packets of the public network.

Views

Security policy rule view

Predefined user roles

network-admin

Parameters

vrf-name: Specifies the name of an MPLS L3VPN instance, a case-sensitive string of 1 to 31 characters.

Usage guidelines

If you execute this command multiple times, the most recent configuration takes effect.

Examples

# Configure security policy rule rule1 to take effect on received packets of MPLS L3VPN instance vpn1.

<Sysname> system-view

[Sysname] security-policy ip

[Sysname-security-policy-ip] rule 0 name rule1

[Sysname-security-policy-ip-0-rule1] user-group groupa

[Sysname-security-policy-ip-0-rule1] user-group groupb

Related commands

display security-policy

19-Security Command Reference

move rule

Cloud & AI

InterConnect

Intelligent Terminal Products

Product Support Services

Technical Service Solutions

Resource Center

Policy

Online Help

Become a Partner

Partner Resources

Partner Business Management

Company Information

News & Events

Contact Us