vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, the command deletes all static routes for the public network.

Usage guidelines

CAUTION:

This command might interrupt network communication and cause packet forwarding failure. Before executing the command, make sure you fully understand the potential impact on the network.

When you use this command, the system will prompt you to confirm the operation before deleting all the static routes.

To delete one static route, use the undo ip route-static command. To delete all static routes, including the default route, use the delete static-routes all command.

Examples

# Delete all static routes.

<Sysname> system-view

[Sysname] delete static-routes all

This will erase all IPv4 static routes and their configurations, you must reconfigure all static routes.

Are you sure?[Y/N]:y

Related commands

ip route-static

display route-static nib

Use display route-static nib to display static route next hop information.

Syntax

display route-static nib [ nib-id ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

nib-id: Specifies a NIB by its ID, a hexadecimal string of 1 to ffffffff. If you do not specify this argument, the command displays all static route next hop information.

verbose: Displays detailed static route next hop information. If you do not specify this keyword, the command displays brief static route next hop information.

Examples

# Displays brief static route next hop information.

<Sysname> display route-static nib

Total number of nexthop(s): 44

NibID: 0x11000000 Sequence: 0

Type: 0x21 Flushed: Yes

UserKey0: 0x111 VrfNthp: 0

UserKey1: 0x0 Nexthop: 0.0.0.0

UserKey2: 0x0 IFIndex: 0x111

UserKey3: 0x0 LocalAddr: 0.0.0.0

TopoNthp: 0

Color: 0 COFlag: 0x0

LinkID: 0x0

SIDIndex: 0x0 SRPName:

OriNexthop: 0.0.0.0

NibID: 0x11000001 Sequence: 1

Type: 0x41 Flushed: Yes

UserKey0: 0x0 VrfNthp: 5

UserKey1: 0x0 Nexthop: 2.2.2.2

UserKey2: 0x0 IFIndex: 0x111

UserKey3: 0x0 LocalAddr: 0.0.0.0

TopoNthp: 0

Color: 0 COFlag: 0x0

LinkID: 0x0

SIDIndex: 0x0 SRPName:

OriNexthop: 0.0.0.0

...

Table 1 Command output

Field	Description
NibID	ID of the NIB.
Sequence	Sequence number of the NIB.
Type	Type of the NIB.
Flushed	Indicates whether the route with the NIB has been flushed to the FIB.
UserKey0	Reserved data 1.
UserKey1	Reserved data 2.
UserKey2	Reserved data 3.
UserKey3	Reserved data 4.
VrfNthp	Index of the VPN instance to which the next hop belongs. This field displays 0 if the next hop is on the public network.
Nexthop	Next hop address.
IFIndex	Interface index
LocalAddr	Local interface address.
TopoNthp	This field is not supported in the current software version. Index of the topology that contains the next hop. This field displays 0 if the next hop is on the public network.
Color	Color extended community attribute.
COFlag	Flag of the color extended community attribute.
LinkID	Link ID of the SDWAN TTE connection.
SIDIndex	SID index value.
SRPName	This field is not supported in the current software version. SR-MPLS TE policy name.
OriNexthop	Original next hop address of the route. If the route is obtained from a BGP UPDATE message, the address is the next hop IP address in the BGP UPDATE message.

# Displays detailed static route next hop information.

<Sysname> display route-static nib verbose

Total number of nexthop(s): 44

NibID: 0x11000000 Sequence: 0

Type: 0x21 Flushed: Yes

UserKey0: 0x111 VrfNthp: 0

UserKey1: 0x0 Nexthop: 0.0.0.0

UserKey2: 0x0 IFIndex: 0x10002

UserKey3: 0x0 LocalAddr: 0.0.0.0

TopoNthp: 0

Color: 0 COFlag: 0x0

LinkID: 0x0

SIDIndex: 0x0 SRPName:

OriNexthop: 0.0.0.0

RefCnt: 2 FlushRefCnt: 0

Flag: 0x2 Version: 1

1 nexthop(s):

PrefixIndex: 0 OrigNexthop: 0.0.0.0

RelyDepth: 0 RealNexthop: 0.0.0.0

Interface: NULL0 LocalAddr: 0.0.0.0

TunnelCnt: 0 Vrf: default-vrf

TunnelID: N/A Topology: base

Weight: 1000000 Flags: 0x0

SRPolicyNID: 4294967295 SRInterface:

ColorWeight: 0 Locator: N/A

OrigLinkID: 0x0 RealLinkID: 0x0

NibID: 0x11000001 Sequence: 1

Type: 0x41 Flushed: Yes

UserKey0: 0x0 VrfNthp: 5

UserKey1: 0x0 Nexthop: 2.2.2.2

UserKey2: 0x0 IFIndex: 0x10002

UserKey3: 0x0 LocalAddr: 0.0.0.0

TopoNthp: 0

Color: 0 COFlag: 0x0

LinkID: 0x0

SIDIndex: 0x0 SRPName:

OriNexthop: 0.0.0.0

RefCnt: 1 FlushRefCnt: 0

Flag: 0x12 Version: 1

2 nexthop(s):

PrefixIndex: 0 OrigNexthop: 2.2.2.2

RelyDepth: 7 RealNexthop: 8.8.8.8

Interface: GE1/0/1 LocalAddr: 12.12.12.12

TunnelCnt: 0 Vrf: default-vrf

TunnelID: N/A Topology: base

Weight: 1000000 Flags: 0x0

SRPolicyNID: 4294967295 SRInterface:

ColorWeight: 0 Locator: N/A

OrigLinkID: 0x0 RealLinkID: 0x0

PrefixIndex: 0 OrigNexthop: 2.2.2.2

RelyDepth: 9 RealNexthop: 0.0.0.0

Interface: NULL0 LocalAddr: 0.0.0.0

TunnelCnt: 0 Vrf: default-vrf

TunnelID: N/A Topology: base

Weight: 1000000 Flags: 0x0

SRPolicyNID: 4294967295 SRInterface:

ColorWeight: 0 Locator: N/A

OrigLinkID: 0x0 RealLinkID: 0x0

...

Table 2 Command output

Field	Description
NibID	ID of the NIB.
Sequence	Sequence number of the NIB.
Type	Type of the NIB.
Flushed	Indicates whether the route with the NIB has been flushed to the FIB.
UserKey0	Reserved data 1.
VrfNthp	Index of the VPN instance that the next hop belongs to. This field displays 0 if the next hop is on the public network.
UserKey1	Reserved data 2.
UserKey2	Reserved data 3.
UserKey3	Reserved data 4.
Nexthop	Next hop address.
IFIndex	Interface index
LocalAddr	Local interface address.
TopoNthp	This field is not supported in the current software version. Index of the topology that contains the next hop. This field displays 0 if the next hop is on the public network.
Color	Color extended community attribute.
COFlag	Flag of the color extended community attribute.
LinkID	Link ID of the SDWAN TTE connection.
SIDIndex	SID index value.
SRPName	This field is not supported in the current software version. SR-MPLS TE policy name.
OriNexthop	Original next hop address of the route. If the route is obtained from a BGP UPDATE message, the address is the next hop IP address in the BGP UPDATE message.
RefCnt	Reference count of the next hop.
FlushRefCnt	Reference count of the next hop that is flushed to the FIB.
Flag	Flag of the next hop.
Version	Version of the next hop.
x nexthop(s)	Number of next hops.
PrefixIndex	Prefix index of the next hop for an ECMP route.
OrigNexthop	Original next hop.
RelyDepth	Recursion depth.
RealNexthop	Real next hop.
Interface	Output interface.
localAddr	Local interface address.
TunnelCnt	Number of tunnels after route recursion.
Vrf	VPN instance name. For the public network, this field displays default-vrf.
TunnelID	ID of the tunnel after route recursion.
Topology	This field is not supported in the current software version. Topology name. The topology name for the public network is base.
Weight	ECMP route weight. This field displays 0 for non-ECMP routes.
Flags	Flags of the detailed next hop.
SRPolicyNID	This field is not supported in the current software version. NIB ID of the route obtained from an SR-MPLS TE policy through route recursion.
SRInterface	This field is not supported in the current software version. Output interface of the route obtained from the SR-MPLS TE policy through route recursion.
ColorWeight	This field is not supported in the current software version. Weight value of the color attribute in the SR-MPLS TE policy.
Locator	IPv6 prefix of the locator to which the SID belongs. If no locator is available, this field displays N/A.
OrigLinkID	Original link ID of the SDWAN TTE connection.
RealLinkID	Real link ID of the SDWAN TTE connection.

‌

display route-static routing-table

Use display route-static routing-table to display static routing table information.

Syntax

display route-static routing-table [ vpn-instance vpn-instance-name ] [ ip-address { mask-length | mask } ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VPN instance, the command displays static routing table information for the public network.

ip-address: Specifies the destination IP address in dotted decimal notation. If you do not specify this argument, the command displays all static routing table information.

mask-length: Specifies the mask length, an integer in the range of 0 to 32.

mask: Specifies the subnet mask in dotted decimal notation.

Examples

# Display static routing table information.

<Sysname> display route-static routing-table

Total number of routes: 24

Status: * - valid

*Destination: 0.0.0.0/0

NibID: 0x1100000a NextHop: 2.2.2.10

MainNibID: N/A BkNextHop: N/A

BkNibID: N/A Interface: GigabitEthernet0/0/1

TableID: 0x2 BkInterface: GigabitEthernet0/0/2

Flag: 0x82d01 BfdSrcIp: N/A

DbIndex: 0xd BfdIfIndex: 0x0

Type: Normal BfdVrfIndex: 0

TrackIndex: 0xffffffff Label: NULL

Preference: 60 vrfIndexDst: 0

BfdMode: N/A vrfIndexNH: 0

Permanent: 0 Tag: 0

Destination: 0.0.0.0/0

NibID: 0x1100000b NextHop: 2.2.2.11

MainNibID: N/A BkNextHop: N/A

BkNibID: N/A Interface: GigabitEthernet0/0/3

TableID: 0x2 BkInterface: GigabitEthernet0/0/4

Flag: 0x82d01 BfdSrcIp: N/A

DbIndex: 0xd BfdIfIndex: 0x0

Type: Normal BfdVrfIndex: 0

TrackIndex: 0xffffffff Label: NULL

Preference: 60 vrfIndexDst: 0

BfdMode: N/A vrfIndexNH: 0

Permanent: 0 Tag: 0

...

Table 3 Command output

Field	Description
destination	Destination address/prefix.
NibID	ID of the NIB.
MainNibID	ID of the primary next hop for static route FRR.
BkNibID	ID of the backup next hop for static route FRR.
NextHop	Next hop address.
BkNextHop	Backup next hop address.
Interface	Output interface of the route.
BkInterface	Backup output interface.
TableID	ID of the table to which the route belongs.
Flag	Flag of the route.
DbIndex	Index of the database to which the route belongs.
Type	Route type: · Normal. · DHCP. · NAT.
BfdSrcIp	Source IP address of the indirect BFD session.
BfdIfIndex	Index of the interface where BFD is enabled.
BfdVrfIndex	Index of the VPN instance where BFD is enabled. This field displays 0 if BFD is enabled for the public network.
BfdMode	BFD session mode: · N/A—No BFD session is configured. · Ctrl—Control packet mode · Echo—Echo packet mode.
TrackIndex	NQA Track index.
vrfIndexDst	Index of VPN instance to which the destination belongs. For the public network, this field displays 0.
vrfIndexNH	Index of the VPN instance to which the next hop belongs. For the public network, this field displays 0.
Permanent	Permanent static route flag. 1 indicates a permanent static route.

ip route-static

Use ip route-static to configure a static route.

Use undo ip route-static to delete a static route.

Syntax

ip route-static dest-address { mask-length | mask } interface-type interface-number [ next-hop-address ] [ backup-interface interface-type interface-number [ backup-nexthop backup-nexthop-address ] [ permanent ] | bfd { control-packet | echo-packet } | permanent | track track-entry-number ] [ preference preference ] [ tag tag-value ] [ description text ]

ip route-static dest-address { mask-length | mask } next-hop-address [ recursive-lookup host-route ] [ bfd control-packet bfd-source ip-address | permanent | track track-entry-number ] [ preference preference ] [ tag tag-value ] [ description text ]

ip route-static dest-address { mask-length | mask } vpn-instance d-vpn-instance-name next-hop-address [ recursive-lookup host-route ] [ bfd control-packet bfd-source ip-address | permanent | track track-entry-number ] [ preference preference ] [ tag tag-value ] [ description text ]

ip route-static group group-name interface-type interface-number [ next-hop-address ] [ backup-interface interface-type interface-number [ backup-nexthop backup-nexthop-address ] [ permanent ] | bfd { control-packet | echo-packet } | permanent | track track-entry-number ] [ preference preference ] [ tag tag-value ] [ description text ]

ip route-static group group-name next-hop-address [ recursive-lookup host-route ] [ bfd control-packet bfd-source ip-address | permanent | track track-entry-number ] [ preference preference ] [ tag tag-value ] [ description text ]

ip route-static group group-name vpn-instance d-vpn-instance-name next-hop-address [ recursive-lookup host-route ] [ bfd control-packet bfd-source ip-address | permanent | track track-entry-number ] [ preference preference ] [ tag tag-value ] [ description text ]

undo ip route-static { dest-address { mask-length | mask } | group group-name } [ interface-type interface-number [ next-hop-address ] | next-hop-address | vpn-instance d-vpn-instance-name next-hop-address ] [ preference preference ]

ip route-static dest-address { mask-length | mask } { srv6-policy { color color-value end-point ipv6 ipv6-address | name policy-name } [ sid sid ] } [ preference preference ] [ tag tag-value ] [ description text ]

undo ip route-static dest-address { mask-length | mask } [ srv6-policy { color color-value end-point ipv6 ipv6-address | name policy-name } ]

Default

No static route is configured.

Views

System view

Predefined user roles

network-admin

Parameters

dest-address: Specifies the destination IP address of the static route, in dotted decimal notation.

mask-length: Specifies the mask length, an integer in the range of 0 to 32.

mask: Specifies the subnet mask in dotted decimal notation.

group group-name: Specifies a static route group by its name, a case-sensitive string of 1 to 31 characters.

vpn-instance d-vpn-instance-name: Specifies a destination MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. If a destination VPN instance is specified, packets will search for the output interface in the destination VPN instance based on the configured next hop address.

interface-type interface-number: Specifies an output interface by its type and number. For more information, see Layer 3—IP Routing Configuration Guide.

next-hop-address: Specifies the IP address of the next hop, in dotted decimal notation. For more information, see Layer 3—IP Routing Configuration Guide.

recursive-lookup host-route: Specifies only host routes for static route recursion.

backup-interface interface-type interface-number: Specifies a backup output interface by its type and number. If the backup output interface is not a P2P interface (for example, a broadcast interface), you must specify the backup next hop address.

backup-nexthop backup-nexthop-address: Specifies a backup next hop address.

bfd: Enables BFD to detect reachability of the static route's next hop. When the next hop is unreachable, the system immediately switches to the backup route.

control-packet: Specifies the BFD control mode.

bfd-source ip-address: Specifies the source IP address of BFD packets. As a best practice, specify the loopback interface address.

echo-packet: Specifies the BFD echo mode.

permanent: Specifies the route as a permanent static route. If the output interface is down, the permanent static route is still active.

track track-entry-number: Associates the static route with a track entry specified by its number in the range of 1 to 1024. For more information about Track, see High Availability Configuration Guide.

public: Indicates that the specified next hop address is on the public network.

srv6-policy name policy-name: Specifies an SRv6 TE policy by its name for static route recursion. The policy-name argument represents the SRv6 TE policy name, a case-sensitive string of 1 to 59 characters. For more information about SRv6 TE policies, see Segment Routing Configuration Guide.

srv6-policy color color-value end-point ipv6 ipv6-address: Specifies an SRv6 TE policy by its color and endpoint attributes for static route recursion. The color-value argument represents the color attribute value of the SRv6 TE policy, in the range of 0 to 4294967295. The ipv6-address argument represents the endpoint IPv6 address of the SRv6 TE policy.

sid sid: Specifies the SRv6 SID of the tail node. Packets forwarded by the specified SRv6 TE policy will continue to be forwarded based on the specified SRv6 SID.

preference preference: Specifies a preference for the static route, in the range of 1 to 255. The default is 60.

tag tag-value: Sets a tag value for marking the static route, in the range of 1 to 4294967295. The default is 0. Tags of routes are used for route control in routing policies. For more information about routing policies, see Layer 3—IP Routing Configuration Guide.

description text: Configures a description of 1 to 60 characters for the static route. The description can include special characters, such as the space, except the question mark (?).

Usage guidelines

If the destination IP address and the mask are both 0.0.0.0 (or 0), the configured route is a default route. The default route is used for forwarding a packet matching no entry in the routing table.

Implement different routing policies to configure different route preferences. For example, to enable load sharing for multiple routes to the same destination, assign the same preference to the routes. To enable the routes to back up one another, assign different preferences to them.

Follow these guidelines when you specify the output interface or the next hop address of the static route:

· If the output interface is a Null 0 interface, no next hop address is required.

· If the output interface is a broadcast interface, the device might have multiple next hops. Therefore, you must specify both the output interface and next hop IP address.

Follow these guidelines when you configure a static route:

· Enabling BFD for a flapping route could worsen the route flapping situation. Therefore, use it with caution. For more information about BFD, see High Availability Configuration Guide.

· For static routing-Track-NQA collaboration, you must configure the same VPN instance ID for the next hop to be detected and the NQA operation.

· If a static route needs route recursion, the associated track entry must monitor the next hop of the recursive route instead of that of the static route. Otherwise, a valid route might be mistakenly considered invalid.

· Do not specify the permanent keyword together with the bfd or track keyword.

If you specify a static route group, all prefixes in the static route group will be assigned the next hop and output interface specified by using this command.

Examples

# Configure a static route, whose destination address is 1.1.1.1/24, next hop address is 2.2.2.2, tag value is 45, and description information is for internet.

<Sysname> system-view

[Sysname] ip route-static 1.1.1.1 24 2.2.2.2 tag 45 description for internet

Related commands

display ip routing-table protocol

ip route-static-group

prefix

ip route-static arp-request

Use ip route-static arp-request to enable periodic sending of ARP requests to the next hops of static routes.

Use undo ip route-static arp-request to disable periodic sending of ARP requests to the next hops of static routes.

Syntax

ip route-static arp-request [ interval interval ]

undo ip route-static arp-request

Default

Periodic sending of ARP requests to the next hops of static routes is disabled.

Views

System view

Predefined user roles

network-admin

Parameters

interval: Specifies an ARP request sending interval in the range of 1 to 300 seconds. The default value is 5.

Usage guidelines

When the following conditions exist, a recursive static route becomes inactive:

· The static route uses a host route to reach its direct next hop.

· The host route is obtained by specifying the recursive-lookup host-route keyword in the ip route-static command or by routing policy-based recursive lookup.

· The host route is unavailable because the direct next hop cannot send gratuitous ARP messages and consequently no ARP entry exists for that host route on the device.

To resolve this issue, you can use this command to enable the device to periodically send ARP requests to the direct next hop. When the device receives an ARP response from the direct next hop, it stops sending ARP requests and activates the recursive static route.

This command applies only to a recursive static route that meets the following requirements:

· The static route has no output interface specified.

· The static route fails the next-hop recursion.

Examples

# Enable sending of ARP requests to the next hops of static routes and set the sending interval to 10 seconds.

<Sysname> system-view

[Sysname] ip route-static arp-request interval 10

Related commands

ip route-static

protocol nexthop recursive-lookup

ip route-static default-preference

Use ip route-static default-preference to configure a default preference for static routes.

Use undo ip route-static default-preference to restore the default.

Syntax

ip route-static default-preference default-preference

undo ip route-static default-preference

Default

The default preference of static routes is 60.

Views

System view

Predefined user roles

network-admin

Parameters

default-preference: Specifies a default preference for static routes, in the range of 1 to 255.

Usage guidelines

If no preference is specified for a static route, the default preference applies.

When the default preference is reconfigured, it applies only to newly added static routes.

Examples

# Set a default preference of 120 for static routes.

<Sysname> system-view

[Sysname] ip route-static default-preference 120

Related commands

display ip routing-table protocol

ip route-static fast-reroute auto

Use ip route-static fast-reroute auto to configure static route FRR to automatically select a backup next hop.

Use undo ip route-static fast-reroute auto to disable static route FRR from automatically selecting a backup next hop.

Syntax

ip route-static fast-reroute auto

undo ip route-static fast-reroute auto

Default

Static route FRR is disabled from automatically selecting a backup next hop.

Views

System view

Predefined user roles

network-admin

Examples

# Configure static route FRR to automatically select a backup next hop.

<Sysname> system-view

[Sysname] ip route-static fast-reroute auto

ip route-static primary-path-detect bfd echo

Use ip route-static primary-path-detect bfd echo to enable BFD echo packet mode for static route FRR.

Use undo ip route-static primary-path-detect bfd to disable BFD echo packet mode for static route FRR.

Syntax

ip route-static primary-path-detect bfd echo

undo ip route-static primary-path-detect bfd

Default

BFD echo packet mode for static route FRR is disabled.

Views

System view

Predefined user roles

network-admin

Usage guidelines

This command enables static route FRR to use BFD echo packet mode for fast failure detection on the primary link.

Examples

# Enable BFD echo packet mode for static route FRR.

<Sysname> system-view

[Sysname] ip route-static 1.1.1.1 32 gigabitethernet 0/0/1 2.2.2.2 backup-interface gigabitethernet 0/0/2 backup-nexthop 3.3.3.3

[Sysname] ip route-static primary-path-detect bfd echo

ip route-static vpn-instance

Use ip route-static vpn-instance to configure a static route in a VPN instance.

Use undo ip route-static vpn-instance to delete a static route from a VPN instance.

Syntax

ip route-static vpn-instance s-vpn-instance-name dest-address { mask-length | mask } interface-type interface-number [ next-hop-address [ nexthop-index index-string ] ] [ backup-interface interface-type interface-number [ backup-nexthop backup-nexthop-address ] [ permanent ] | bfd { control-packet | echo-packet } | permanent | track track-entry-number ] [ preference preference ] [ tag tag-value ] [ description text ]

ip route-static vpn-instance s-vpn-instance-name dest-address { mask-length | mask } next-hop-address [ nexthop-index index-string ] [ recursive-lookup host-route ] [ public ] [ bfd control-packet bfd-source ip-address | permanent | track track-entry-number ] [ preference preference ] [ tag tag-value ] [ description text ]

ip route-static vpn-instance s-vpn-instance-name dest-address { mask-length | mask } vpn-instance d-vpn-instance-name next-hop-address [ nexthop-index index-string ] [ recursive-lookup host-route ] [ bfd control-packet bfd-source ip-address | permanent | track track-entry-number ] [ preference preference ] [ tag tag-value ] [ description text ]

ip route-static vpn-instance s-vpn-instance-name group group-name interface-type interface-number [ next-hop-address ] [ backup-interface interface-type interface-number [ backup-nexthop backup-nexthop-address ] [ permanent ] | bfd { control-packet | echo-packet } | permanent | track track-entry-number ] [ preference preference ] [ tag tag-value ] [ description text ]

ip route-static vpn-instance s-vpn-instance-name group group-name next-hop-address [ recursive-lookup host-route ] [ public ] [ bfd control-packet bfd-source ip-address | permanent | track track-entry-number ] [ preference preference ] [ tag tag-value ] [ description text ]

ip route-static vpn-instance s-vpn-instance-name group group-name vpn-instance d-vpn-instance-name next-hop-address [ recursive-lookup host-route ] [ bfd control-packet bfd-source ip-address | permanent | track track-entry-number ] [ preference preference ] [ tag tag-value ] [ description text ]

undo ip route-static vpn-instance s-vpn-instance-name { dest-address { mask-length | mask } | group group-name } [ interface-type interface-number [ next-hop-address ] | next-hop-address [ public ] | vpn-instance d-vpn-instance-name next-hop-address ] [ preference preference ]

ip route-static vpn-instance s-vpn-instance-name dest-address { mask-length | mask } { srv6-policy { color color-value end-point ipv6 ipv6-address | name policy-name } [ sid sid ] } [ preference preference ] [ tag tag-value ] [ description text ]

undo ip route-static vpn-instance s-vpn-instance-name dest-address { mask-length | mask } [ srv6-policy { color color-value end-point ipv6 ipv6-address | name policy-name } ]

Default

No static route is configured in a VPN instance.

Views

System view

Predefined user roles

network-admin

Parameters

vpn-instance s-vpn-instance-name: Specifies a source MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. Each VPN instance has its own routing table, and the configured static route is installed in the routing tables of the specified VPN instances.

dest-address: Specifies the destination IP address of the static route, in dotted decimal notation.

mask-length: Specifies the mask length, an integer in the range of 0 to 32.

mask: Specifies the subnet mask in dotted decimal notation.

group group-name: Specifies a static route group by its name, a case-sensitive string of 1 to 31 characters.

interface-type interface-number: Specifies an output interface by its type and number. For more information, see Layer 3—IP Routing Configuration Guide.

next-hop-address: Specifies the IP address of the next hop, in dotted decimal notation. For more information, see Layer 3—IP Routing Configuration Guide.

nexthop-index index-string: Specifies the index of the next hop. The index-string argument represents the index, which is a case-insensitive string of 1 to 93 characters. If you do not specify an index for the next hop, the static route uses the output interface and the IP address of the next hop as the next hop index. Do not specify the same next hop index for routes to the same destination.

recursive-lookup host-route: Specifies only host routes for static route recursion.

backup-interface interface-type interface-number: Specifies a backup output interface by its type and number. If the backup output interface is a non-P2P interface (a broadcast interface), you must specify the backup next hop address.

backup-nexthop backup-nexthop-address: Specifies a backup next hop address.

bfd: Enables BFD to detect reachability of the static route's next hop. When the next hop is unreachable, the system immediately switches to the backup route.

control-packet: Specifies the BFD control mode.

bfd-source ip-address: Specifies the source IP address of BFD packets. As a best practice, specify the loopback interface address.

echo-packet: Specifies the BFD echo mode.

permanent: Specifies the route as a permanent static route. If the output interface is down, the permanent static route is still active.

public: Specifies the public network, which indicates that the specified next hop address is on the public network.

sid sid: Specifies the SRv6 SID of the tail node. Packets forwarded by the specified SRv6 TE policy will continue to be forwarded based on the specified SRv6 SID.

preference preference: Specifies a preference for the static route, in the range of 1 to 255. The default is 60.

description text: Configures a description of 1 to 60 characters for the static route. The description can include special characters, such as the space, except the question mark (?).

Usage guidelines

If the destination IP address and the mask are both 0.0.0.0 (or 0), the configured route is a default route. The default route is used for forwarding a packet matching no entry in the routing table.

Follow these guidelines when you specify the output interface or the next hop address of the static route:

· If the output interface is a Null 0 interface, no next hop address is required.

· If the output interface is a broadcast interface that might have multiple next hops, you must specify both the output interface and next hop IP address.

Follow these guidelines when you configure a static route:

· Enabling BFD for a flapping route could worsen the route flapping situation. Therefore, use it with caution. For more information about BFD, see High Availability Configuration Guide.

· For static routing-Track-NQA collaboration, you must configure the same VPN instance ID for the next hop to be detected and the NQA operation.

· If a static route needs route recursion, the associated track entry must monitor the next hop of the related route instead of that of the recursive static route. Otherwise, a valid route might be mistakenly considered invalid.

· You cannot specify the permanent keyword together with the bfd and track keywords.

If you specify a static route group, all prefixes in the static route group will be assigned the next hop and output interface specified by using this command.

Examples

# Configure a static route in VPN instance vpn1, whose destination address is 1.1.1.1/24, next hop address is 2.2.2.2 in VPN instance vpn2, tag value is 45, and description information is for internet.

<Sysname> system-view

[Sysname] ip route-static vpn-instance vpn1 1.1.1.1 24 vpn-instance vpn2 2.2.2.2 tag 45 description for internet

Related commands

display ip routing-table protocol

ip route-static-group

prefix

ip route-static-group

Use ip route-static-group to create a static route group and enter its view, or enter the view of an existing static route group.

Use undo ip route-static-group to delete a static route group.

Syntax

ip route-static-group group-name

undo ip route-static-group group-name

Default

No static route groups exist.

Views

System view

Predefined user roles

network-admin

Parameters

group-name: Specifies the static route group name, a case-sensitive string of 1 to 31 characters.

Examples

# Create static route group test and enter its view.

<Sysname> system-view

[Sysname] ip route-static-group test

[Sysname-route-static-group-test]

Related commands

ip route-static

prefix

Use prefix to add a static route prefix to a static route group.

Use undo prefix to delete a static route prefix from a static route group.

Syntax

prefix dest-address { mask-length | mask }

undo prefix dest-address { mask-length | mask }

Default

No static route prefix is added to a static route group.

Views

Static route group view

Predefined user roles

network-admin

Parameters

dest-address: Specifies the destination IP address of the static route, in dotted decimal notation.

mask-length: Specifies the mask length, an integer in the range of 0 to 32.

mask: Specifies the subnet mask in dotted decimal notation.

Usage guidelines

Execute this command repeatedly to add multiple static route prefixes to a static route group.

After you add static route prefixes to a static route group, you can specify that group in the ip route-static group command to configure static routes with the prefixes. To configure more static routes, you only need to add new static route prefixes to the group.

Examples

# Add static route prefix 1.1.1.1/32 to static route group test.

<Sysname> system-view

[Sysname] ip route-static-group test

[Sysname-route-static-group-test] prefix 1.1.1.1 32

Related commands

ip route-static

ip route-static-group

08-Layer 3—IP Routing Command Reference

Static routing commands

delete static-routes all

display route-static nib

display route-static routing-table

ip route-static

ip route-static arp-request

ip route-static default-preference

ip route-static fast-reroute auto

ip route-static primary-path-detect bfd echo

ip route-static vpn-instance

ip route-static-group

prefix

Cloud & AI

InterConnect

Intelligent Computing

Security

SMB Products

Intelligent Terminal Products

Industry Solutions

Product Support Services

Technical Service Solutions

Resource Center

Policy

Online Help

Training & Certification

Become a Partner

Partner Resources

Partner Business Management

Company Information

News & Events

Online Exhibition Center

Contact Us