cellular [ interface-number ]: Specifies a cellular interface by its number. If you do not specify a cellular interface, this command displays call connection information for all cellular interfaces with mobile communication modems installed.

Examples

# Display call connection information for a 5G modem (LTE network).

<sysname>display cellular 0/0

Cellular0/0:

Modem State:

Hardware Information:

Model: RM500QGL_VH

Manufacturer: QUALCOMM INCORPORATED

Modem Firmware Version: RM500QGLABR01A01M4G

International Mobile Equipment Identity (IMEI): 863305040121609

International Mobile Subscriber Identity (IMSI): 460028012255957

Hardware Version: 20000

Modem Status: Online

Modem Status: IPv4 Active.

Modem Status: IPv6 Unknown.

Profile Information:

Profile index: 1

PDP Type: IPv4v6

Header Compression: Off

Data Compression: Off

Access Point Name (APN): cmiot

Authentication: NONE

* - Default profile

Profile index: 2

PDP Type: IPv4v6

Header Compression: Off

Data Compression: Off

Access Point Name (APN): ims

Authentication: NONE

Profile index: 3

PDP Type: IPv4v6

Header Compression: Off

Data Compression: Off

Access Point Name (APN): CMNET

Authentication: NONE

Profile index: 4

PDP Type: IPv4v6

Header Compression: Off

Data Compression: Off

Access Point Name (APN): CMWAP

Authentication: NONE

Profile index: 5

PDP Type: IPv4v6

Header Compression: Off

Data Compression: Off

Access Point Name (APN): SOS

Authentication: NONE

Network Information:

Current Service Status: Service Available

Registration Status: Registered

Current Service: Combined

Current Roaming Status: Home

Current Data Bearer Technology = NR

Network Selection Mode: Automatic

Current IP address Mode: Cellular-alloc

Current IPV6 address Mode: Unknown

Mobile Network Name: C

Mobile Country Code (MCC): 460

Mobile Network Code (MNC): 00

Tracking Area Code(TAC): 4526

Cell ID: 20027137

Radio Information:

Technology Preference: No preference specified (AUTO)

Technology Selected: NR && LTE

Configured LTE Band = 1,2,3,4,5,7,8,12,13,14,17,18,19,20,25,26,28,29,30,32,34,38,39,40,41,42,43

5G availability under LTE system info:

Current PCI: 537

Endc Available: 1

Restrict Dcnr: 0

R15Availabe: 1

NR related info:

Current RSRQ: -12 dB

Current RSRP: -93 dBm

Current SNR: 14 dB

LTE related info:

Current RSSI: -65 dBm

Current RSRQ: -13 dB

Current RSRP: -103 dBm

Current SNR: -2 dB

Tx Power: 10 dBm

Active Band = E-UTRA Operating Band 39

Modem Security Information:

PIN Verification: Disabled

PIN Status: PIN Requirement Disabled

Number of PIN Retries Remaining: 3

Number of PUK Retries Remaining: 10

SIM Status: OK

ICCID: 898600100119F0111820

SIM Number Information:

SIM Number: 0

Error Information:

IPv4 dialing failed: 0x00: No error in the request

IPv6 dialing failed: N/A

GNSS Information:

GNSS Info:

GNSS State: Enabled

GNSS Mode Configured: Standalone

Latitude(WGS84): 31 Deg 50 Min 21.17 Sec North

Longitude(WGS84): 117 Deg 7 Min 47.22 Sec East

Timestamp (UTC): 09/24/2020 01:27:26

Local time: 09/24/2020 09:27:26

Heading: 0.00, Velocity Horiz: 0.00, Velocity Vert: 0.00

Height (MSL): 212.30 m

Satellite Info:

Satellite ID: #2

SvSystem:GPS Elevation: 44.00, Azimuth: 309.00, SNR: 33.00, Processing Status: Track

Satellite ID: #1

SvSystem:BEIDOU Elevation: 61.00, Azimuth: 116.00, SNR: 40.00, Processing Status: Track

Satellite ID: #7

SvSystem:GALILEO Elevation: 42.00, Azimuth: 71.00, SNR: 44.00, Processing Status: Track

Table 1 Command output

Field	Description
Modem Status	Status of the modem: · Online—The modem is powered on. · Offline—The modem is powered off or in lower power mode. The cellular interface is not available. · IPv4 Active—IPv4 dialup is activated. · IPv4 Inactive—IPv4 dialup is not activated. · IPv4 Unknown—IPv4 dialup is disabled. · IPv6 Active—IPv6 dialup is activated. · IPv6 Inactive—IPv6 dialup is not activated. · IPv6 Unknown—IPv6 dialup is disabled.
PDP Type	PDP type, displayed only when Profile 1 is Active: · IPv4. · IPv6. · PPP (transparent transmission).
Header Compression	PDP header compression status: · On. · Off.
Data Compression	PDP data compression status: · On. · Off.
Authentication	Authentication mode: · NONE—No authentication. · CHAP—CHAP authentication. · PAP—PAP authentication. · PAP or CHAP—PAP or CHAP authentication.
Current Service Status	Service providing status of the modem: · Limited—The modem is not in the coverage of the selected network. The cellular interface is not available. · Service available—The modem is providing services correctly. · Emergency—The modem is providing limited services. The cellular interface is not available. · No service—The modem cannot provide services. The cellular interface is not available. · Low power—The modem is in low power mode. The cellular interface is not available.
Registration Status	Network registration status: · Registered—The modem has been registered to a network. · Not Registered—The modem has not been registered to a network. · Searching—The modem is searching for networks. · Denied—The modem has been denied from registration to a network. · Unknown—Other status.
Current Service	Current service status: · Combined. · Invalid. · Circuit-switched. · Packet-switched.
Current Roaming Status	Roaming status: · Roaming. · Home.
Current Data Bearer Technology	Current data carrier technology: · CDMA2000 1X. · CDMA2000 HRPD (1xEV-DO). · GSM. · UMTS. · CDMA2000 HRPD (1xEV-DO RevA). · EDGE. · HSDPA and WCDMA. · WCDMA and HSUPA. · HSDPA and HSUPA. · LTE. · NR. · CDMA2000 EHRPD. · HSDPA+ and WCDMA. · HSDPA+ and HSUPA. · DC_HSDPA+ and WCDMA. · DC_HSDPA+ and HSUPA. · HSDPA+ and 64QAM. · HSDPA+, 64QAM and HSUPA. · TDSCDMA. · TDSCDMA and HSDPA. · Unknown.
Network Selection Mode	Network selection mode · Manual. · Automatic.
Current IP address Mode	IPv4 address allocation method: · Cellular-alloc—Modem configuration. · dhcp-alloc—DHCP allocation. · Manual—Manual specification. · Unknown—Other allocation method.
Current IPV6 address Mode	IPv6 address allocation method: · Cellular-alloc—Modem configuration. · dhcp-alloc—DHCP allocation. · Manual—Manual specification. · Unknown—Other allocation method.
Mobile Country Code(MCC)	This information is displayed only when a network is found.
Mobile Network Code(MNC)	This information is displayed only when the modem has been registered to a network.
Tracking Area Code(TAC)	This information is displayed only when the modem has been registered to a network.
Cell ID	This information is displayed only when the modem has been registered to a network.
Radio Information	Wireless communication information
Technology Preference	Network connecting preference: · AUTO—Automatically selects a network for connection. · GSM only—Connects only to a GSM network. · GSM precedence—Connects preferentially to a GSM network. · WCDMA only—Connects only to a WCDMA network. · WCDMA precedence—Connects preferentially to a WCDMA network. · TD-SCDMA only—Connects only to a TD-SCDMA network. · TD-SCDMA precedence—Connects preferentially to a TD-SCDMA network. · EVDO—Connects only to a CDMA-EVDO network. · 1x RTT—Connects only to a CDMA-1x RTT network. · 1xRTT/EVDO HYBRID—Connects to CDMA-EVDO and CDMA-1x RTT networks simultaneously. · LTE only—Connects only to an LTE network. · NR only—Connects only to an NR network.
Technology Selected	Currently connected network: · GSM—Has connected to a GSM network. · WCDMA—Has connected to a WCDMA network. · TD-SCDMA—Has connected to a TD-SCDMA network. · EVDO—Has connected to a CDMA-EVDO network. · 1Xrtt—Has connected to a CDMA-1x RTT network. · 1xRTT/EVDO HYBRID—Has connected to the CDMA-EVDO and CDMA-1x RTT networks simultaneously. · LTE—Has connected to an LTE network. · NR && LTE—Has connected to an NR+LTE network (NSA networking) · NR—Has connected to an NR network.
5G availability under LTE system info	5G base station settings configured in NSA networking.
Current PCI	Current physical cell ID.
Endc Available	Whether 5G services are available (indicated by the SIB2 message).
Restrict Dcnr	Whether the modem can connect to both LTE and NR base stations.
R15Availabe	Whether R15 can be used (indicated by the PLMN message of the base station).
Current RSRQ	Current reference signal received quality.
Current RSRP	Current reference signal received power.
Current SNR	Current signal-to-noise ratio.
Current RSSI	The value is in the range of –110 dBm to –51 dBm. This field displays Unknown when no signal is received and the cellular interface is not available.
Tx Power	Signal transmit power.
Active Band	Band No. of the base station.
PIN Verification	PIN authentication status: · Disabled. · Enabled. · Unknown.
PIN Status	· Ready—The SIM card is normal. · PIN Requirement—Requires you to execute the pin verify command to enter the PIN for PIN verification. · PUK Requirement—Requires you to execute the pin unlock command to unlock the SIM or UIM card.
Number of PIN Retries Remaining	Remaining retries available for entering the PIN.
Number of PUK Retries Remaining	Remaining retries available for entering the PUK.
SIM Status	SIM card status: · OK—The SIM card is normal. · Locked—The SIM card is locked. The cellular interface is not available. · Not Inserted—No SIM card is present. The cellular interface is not available · Unknown—The SIM card status is unknown.
ICCID	ID of the SIM card, displayed only when the SIM card status is OK.
SIM Number Information	Slot information for the active SIM card.
SIM Number	Slot number for the active SIM card. The available values are 0 and 1.
IPv4 dialing failed	The system returns 0x00 if IPv4 dialup failed and displays N/A if no IPv4 dialup is performed.
IPv6 dialing failed	The system returns 0x00 if IPv6 dialup failed and displays N/A if no IPv6 dialup is performed.

‌

display controller cellular

Use display controller cellular to display information about cellular interfaces.

Syntax

display controller [ cellular [ interface-number ] ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

cellular [ interface-number ]: Specifies cellular interfaces or a cellular interface by its number. If you do not specify the cellular keyword, this command displays information about all interfaces. If you specify the cellular keyword but not the interface-number argument, this command displays information about all cellular interfaces.

Examples

# Display information about Cellular 2/4/0.

<Sysname> display controller cellular 2/4/0

Cellular2/4/0

Current state: UP

Description: Cellular2/4/0 Interface

Modem status: Present

DM port status: Disabled

Capability:

1 Control channel, 1 PPP channel

Control channel 0 traffic statistics:

TX: 0 packets, 0 errors

RX: 0 packets, 0 errors

PPP channel 0 traffic statistics:

TX: 0 packets, 0 errors

RX: 0 packets, 0 errors

Table 2 Command output

Field	Description
Cellular2/4/0 Current state	Status of the interface: · DOWN(Administratively)—The interface has been administratively shut down by using the shutdown command. · DOWN—The interface is administratively up but its physical state is down, possibly because of a connection or link failure. · UP—The administrative and physical states of the interface are both up.
Description	Description of the interface.
Modem status	This field is not supported in the current software version. Status of the USB mobile communication modem: · Present—The modem is present. · Absent—The modem is absent.
DM port status	DM status: · Enabled. · Disabled.
Capability: 1 Control channel, 1 PPP channel	Type and number of channels the cellular interface supports: · 1 Control channel—Supports one control channel. · 1 PPP channel—Supports one asynchronous serial subchannel. · 1 ETH channel—Supports one Ethernet subchannel.
Control channel 0 traffic statistics: TX: 0 packets, 0 errors RX: 0 packets, 0 errors	Control channel statistics: · TX: 0 packets, 0 errors—Number of packets and number of error packets sent through the control channel. · RX: 0 packets, 0 errors—Number of packets and number of error packets received through the control channel.
PPP channel 0 traffic statistics TX: 0 packets, 0 errors RX: 0 packets, 0 errors	PPP channel statistics: · TX: 0 packets, 0 errors—Number of packets and number of error packets sent through the PPP channel. · RX: 0 packets, 0 errors—Number of packets and number of error packets received through the PPP channel.
ETH channel 0 traffic statistics TX: 0 packets, 0 errors RX: 0 packets, 0 errors	Ethernet channel statistics: · TX: 0 packets, 0 errors—Number of packets and number of error packets sent through the Ethernet channel. · RX: 0 packets, 0 errors—Number of packets and number of error packets received through the Ethernet channel.

Field

Description

Cellular2/4/0

Current state

Status of the interface:

· DOWN(Administratively)—The interface has been administratively shut down by using the shutdown command.

· DOWN—The interface is administratively up but its physical state is down, possibly because of a connection or link failure.

· UP—The administrative and physical states of the interface are both up.

Description

Description of the interface.

Modem status

This field is not supported in the current software version.

Status of the USB mobile communication modem:

· Present—The modem is present.

· Absent—The modem is absent.

DM port status

DM status:

· Enabled.

· Disabled.

Capability:

1 Control channel, 1 PPP channel

Type and number of channels the cellular interface supports:

· 1 Control channel—Supports one control channel.

· 1 PPP channel—Supports one asynchronous serial subchannel.

· 1 ETH channel—Supports one Ethernet subchannel.

Control channel 0 traffic statistics:

TX: 0 packets, 0 errors

RX: 0 packets, 0 errors

Control channel statistics:

· TX: 0 packets, 0 errors—Number of packets and number of error packets sent through the control channel.

· RX: 0 packets, 0 errors—Number of packets and number of error packets received through the control channel.

PPP channel 0 traffic statistics

TX: 0 packets, 0 errors

RX: 0 packets, 0 errors

PPP channel statistics:

· TX: 0 packets, 0 errors—Number of packets and number of error packets sent through the PPP channel.

· RX: 0 packets, 0 errors—Number of packets and number of error packets received through the PPP channel.

ETH channel 0 traffic statistics

TX: 0 packets, 0 errors

RX: 0 packets, 0 errors

Ethernet channel statistics:

· TX: 0 packets, 0 errors—Number of packets and number of error packets sent through the Ethernet channel.

· RX: 0 packets, 0 errors—Number of packets and number of error packets received through the Ethernet channel.

‌

Related commands

reset counters controller cellular

dm-port open

Use dm-port open to enable diagnostic and monitoring (DM) on a mobile communication modem.

Use undo dm-port open to disable DM on a mobile communication modem.

Syntax

dm-port open

undo dm-port open

Default

The default setting for this command depends on the modem model.

Views

Cellular interface view

Predefined user roles

network-admin

Usage guidelines

Enabling DM on a mobile communication modem allows third-party debugging tools to diagnose and monitor the mobile communication modem through cellular interface debugging output.

Examples

# Enable DM on a mobile communication modem.

<Sysname> system-view

[Sysname] controller cellular 2/4/0

[Sysname-Cellular2/4/0] dm-port open

mode

Use mode to specify the network connection preference.

Syntax

mode { auto | lte | nr| wcdma | wcdma-precedence }

Default

The default setting for this command depends on the modem model.

Views

Cellular interface view

Predefined user roles

network-admin

Parameters

auto: Connects to a network automatically.

lte: Connects only to an LTE network.

nr: Connects only to an NR network.

wcdma: Connects only to a WCDMA network.

wcdma-preference: Connects to a WCDMA network preferentially.

Usage guidelines

The available parameters depend on the modem model.

Specify the nr keyword with caution. On an NSA network, if you specify the nr keyword for the modem to connect only to an NR network, the modem might fail to connect to the Internet.

Examples

# Specify the LTE service for the 5G modem.

<Sysname> system-view

[Sysname] controller cellular 2/4/0

[Sysname-Cellular2/4/0] mode lte

modem reboot

Use modem reboot to reboot a mobile communication modem.

Syntax

modem reboot

Views

Cellular interface view

Predefined user roles

network-admin

Usage guidelines

CAUTION:

Execute this command with caution. It will disconnect the established modem connections.

A mobile communication modem module can automatically detect running errors and reboot. If the mobile communication modem fails to reboot by itself, you can use this command to reboot it.

Examples

# Manually reboot the mobile communication modem.

<Sysname> system-view

[Sysname] controller cellular 2/4/0

[Sysname-Cellular2/4/0] modem reboot

modem response

Use modem response to set a mobile communication modem response timer and a consecutive response failure threshold for auto recovery.

Use undo modem response to restore the default.

Syntax

modem response timer time auto-recovery threshold

undo modem response

Default

The response timer is 10 seconds and the consecutive response failure threshold is 3.

Views

Cellular interface view

Predefined user roles

network-admin

Parameters

timer time: Sets the response timer, in the range of 1 to 300, in seconds.

auto-recovery threshold: Specifies the consecutive response failure threshold for auto recovery. The value range for the threshold argument is 0 to 10. To disable auto recovery, set the value to 0.

Usage guidelines

A mobile communication modem might malfunction in an unstable mobile communication network or when the application environment changes. During a malfunction, the modem cannot respond to the device's requests or configuration commands. If the device does not receive any responses from the mobile communication modem before the timer times out, a response failure occurs. When the number of consecutive response failures reaches the threshold, the device restarts the mobile communication modem automatically. This releases the user from manually rebooting the modem.

The device does not restart the mobile communication modem when the mobile communication modem has not made a successful dialup since the last restart. This restriction avoids repeated restarts of the mobile communication modem when there are configuration errors.

Examples

# Set the response timer to 20 seconds and the consecutive response failure threshold for auto recovery to 4.

<Sysname> system-view

[Sysname] controller cellular 2/4/0

[Sysname-Cellular2/4/0] modem response timer 20 auto-recovery 4

pin modify

Use pin modify to modify the PIN of a SIM/UIM card.

Syntax

pin modify current-pin new-pin

Views

Cellular interface view

Predefined user roles

network-admin

Parameters

current-pin: Specifies the current PIN of the SIM/UIM card, a string of 4 to 8 digits.

new-pin: Specifies the new PIN, a string of 4 to 8 digits.

Usage guidelines

The new PIN is saved on the SIM/UIM card.

If PIN verification is enabled, execute the pin verify command to save the new PIN on the device after the PIN is modified.

Failure to modify the PIN in a maximum number of attempts locks the SIM/UIM card. The maximum number of attempts depend on the mobile communication modem model. To unlock the card, execute the pin unlock command.

For some mobile communication modems, you can modify their PINs only when the mobile communication modems pass the PIN authentication.

Examples

# Modify the PIN of a SIM/UIM card.

<Sysname> system-view

[Sysname] controller cellular 2/4/0

[Sysname-Cellular2/4/0] pin modify 1234 4321

PIN will be changed to “4321”. Continue? [Y/N]:y

PIN has been changed successfully.

Related commands

pin unlock

pin verification enable

pin verify

pin unlock

Use pin unlock to specify the Personal Unlock Code (PUK) to unlock a SIM/UIM card.

Syntax

pin unlock puk new-pin

Views

Cellular interface view

Predefined user roles

network-admin

Parameters

puk: Specifies the PUK of the SIM/UIM card, a string of 4 to 8 digits. The PUK code of a SIM/UIM card is provided by the network service provider.

new-pin: Specifies the new PIN, a string of 4 to 8 digits.

Usage guidelines

A SIM/UIM card will be locked in the following circumstances:

· Consecutive PIN modification failures.

· Consecutive failures for enabling or disabling PIN authentication.

· Consecutive PIN authentication failures.

If the SIM/UIM card is locked, the modem cannot be used. To unlock the card, you can use the pin unlock command. The new PIN is saved on the SIM/UIM card.

If PIN verification is enabled, use the pin verify command to save the new PIN on the device after the SIM/UIM card is unlocked.

If you consecutively fail to unlock a card by using the PUK, the card will be locked permanently. To unlock a permanently locked card, contact the service provider of the card.

Examples

# Use the PUK to unlock a SIM/UIM card.

<Sysname> system-view

[Sysname] controller cellular 2/4/0

[Sysname-Cellular2/4/0] pin unlock 87654321 1234

PIN will be unlocked and changed to “1234”. Continue? [Y/N]:y

PIN has been unlocked and changed successfully.

Related commands

pin modify

pin verification enable

Use pin verification enable to enable PIN verification for a mobile communication modem.

Use undo pin verification enable to disable PIN verification for a mobile communication modem.

Syntax

pin verification enable [ pin ]

undo pin verification enable [ pin ]

Default

The default setting for this command depends on the modem model.

Views

Cellular interface view

Predefined user roles

network-admin

Parameters

pin: Specifies the PIN of the SIM/UIM card, a string of 4 to 8 digits.

Usage guidelines

If PIN verification is enabled, PIN verification is performed after you perform any of the following tasks:

· Install a mobile communication modem.

· Reboot the mobile communication modem.

¡ Reboot the device.

¡ Execute the modem reboot command to reboot the modem.

To perform PIN verification, you also need to execute the pin verify command to save the PIN of the SIM/UIM card on the device. After the PIN is saved on the device, the PIN is used for verification automatically when required.

You might be required to provide the current PIN when you enable or disable PIN verification. Consecutive failures for enabling or disabling PIN verification lock a SIM/UIM card. To unlock the card, execute the pin unlock command.

For some mobile communication modems, you can disable PIN verification only when the mobile communication modems pass PIN authentication.

Examples

# Enable PIN authentication.

<Sysname> system-view

[Sysname] controller cellular 2/4/0

[Sysname-Cellular2/4/0] pin verification enable 1234

Related commands

pin unlock

pin verify

Use pin verify to specify the PIN of a SIM/UIM card on a mobile communication modem.

Use undo pin verify to restore the default.

Syntax

pin verify { cipher | simple } string

undo pin verify

Default

No PIN is specified for a SIM/UIM card.

Views

Cellular interface view

Predefined user roles

network-admin

Parameters

cipher ciphered-pin: Specifies a PIN in encrypted form.

simple pin: Specifies a PIN in plaintext form. For security purposes, the PIN specified in plaintext form will be stored in encrypted form.

string: Specifies the PIN. Its plaintext form is 4 to 8 digits long. Its encrypted form is a string of 37 to 41 characters.

Usage guidelines

This command saves the PIN of the SIM/UIM card on the device. The PIN is used for verifying the mobile communication modem when PIN verification is performed. You can execute this command before or after you enable PIN verification.

Consecutive PIN verification failures might lock a SIM/UIM card. To unlock the card, execute the pin unlock command.

Examples

# Specify the plaintext form PIN 1234 for the SIM/UIM card.

<Sysname> system-view

[Sysname] controller cellular 2/4/0

[Sysname-Cellular2/4/0] pin verify simple 1234

Related commands

pin unlock

pin verification enable

plmn search

Use plmn search to search for available mobile networks.

Syntax

plmn search

Views

Cellular interface view

Predefined user roles

network-admin

Usage guidelines

Before you use a mobile communication modem to access a mobile network, use the plmn search command to search a PLMN for available mobile networks. The search takes a few minutes. After the search is complete, the CLI displays the available mobile networks. Some mobile communication modems automatically access an available network. You can also specify a mobile network for the mobile communication modem from the available mobile networks.

Examples

# Search for mobile networks on Cellular 2/4/0.

<Sysname> system-view

[Sysname] controller cellular 2/4/0

[Sysname-Cellular2/4/0] plmn search

PLMN search done.

Available PLMNs:

PLMN No. MCC MNC Status Type

01 460 00 Current GSM

02 460 00 Available UTRAN

03 460 01 Forbidden GSM

Table 3 Command output

Field	Description
PLMN No	PLMN number.
MCC	Mobile Country Code.
MNC	Mobile Network Code: · 00, 02, and 07—China Mobile. · 01—China Unicom. · 03—China Telecom.
Status	Status of the mobile network: · Current. · Available. · Forbidden.
Type	Type of the mobile network.

Related commands

display cellular

plmn select

Use plmn select to configure the mobile network selection mode.

Syntax

plmn select { auto | manual mcc mnc }

Default

The default setting for this command depends on the modem model.

Views

Cellular interface view

Predefined user roles

network-admin

Parameters

auto: Specifies the auto selection mode. The modem automatically selects a mobile network.

manual: Specifies the manual selection mode.

mcc: Specifies the mobile country code (MCC) in the range of 0 to 65535.

mnc: Specifies the mobile network code (MNC) in the range of 0 to 65535.

Usage guidelines

For manual selection, you can first use the plmn search command to obtain the MCC and MNC of a mobile network.

Examples

# Manually specify a mobile network.

<Sysname> system-view

[Sysname] controller cellular 2/4/0

[Sysname-Cellular2/4/0] plmn select manual 65524 65524

Related commands

display cellular

plmn search

reset counters controller cellular

Use reset counters controller cellular to clear statistics on cellular interfaces.

Syntax

reset counters controller cellular [ interface-number ]

Views

User view

Predefined user roles

network-admin

Parameters

cellular [ interface-number ]: Specifies cellular interfaces or a cellular interface by its number. If you do not specify the interface-number argument, this command clears statistics on all cellular interfaces. If you specify the interface-number argument, this command clears statistics on the specified cellular interface.

Usage guidelines

To collect traffic statistics on an interface during a period of time, first use the reset counters controller cellular command to clear the existing statistics on the interface.

Examples

# Clear statistics on Cellular 2/4/0.

<Sysname> reset counters controller cellular 2/4/0

Related commands

display controller cellular

rssi

Use rssi to set the RSSI thresholds for a mobile communication modem.

Use undo rssi to restore the default.

Syntax

rssi { 1xrtt | evdo | gsm | lte } { low lowthreshold | medium mediumthreshold } *

undo rssi { 1xrtt | evdo | gsm | lte } [ low | medium ]

Default

The lower and upper RSSI thresholds for a mobile communication modem are –150 dBm and 0 dBm, respectively.

Views

Cellular interface view

Predefined user roles

network-admin

Parameters

1xrtt: Specifies the 1xRTT mode.

evdo: Specifies the EVDO mode.

gsm: Specifies the GSM mode.

lte: Specifies the LTE mode.

low lowthreshold: Specifies the lower RSSI threshold value in the range of 0 to 150, which represents a lower RSSI threshold in the range of –150 dBm to 0 dBm. The value of lowthreshold cannot be smaller than the value of mediumthreshold because the system automatically adds a negative sign to the RSSI thresholds.

medium mediumthreshold: Specifies the upper RSSI threshold value in the range of 0 to 150, which represents an upper RSSI threshold in the range of –150 dBm to 0 dBm.

Usage guidelines

The device performs the following operations based on the actual RSSI of the mobile communication modem:

· Sends a trap that indicates high RSSI when the RSSI exceeds the upper threshold.

· Sends a trap that indicates normal RSSI when the RSSI is between the lower threshold and upper threshold (included).

· Sends a trap that indicates low RSSI when the RSSI drops to or below the lower threshold.

· Sends a trap that indicates low RSSI every 10 minutes when the RSSI remains equal to or smaller than the lower threshold.

To view the RSSI change information for a mobile communication modem, use the display cellular command.

Examples

# Set the lower threshold for a mobile communication modem in GSM mode to –110 dBm.

<Sysname> system-view

[Sysname] controller cellular 0/0

[Sysname-Cellular0/0] rssi gsm low 110

sendat

Use sendat to issue a configuration directive to a mobile communication modem.

Syntax

sendat at-string

Views

Cellular interface view

Predefined user roles

network-admin

Parameters

at-string: Specifies a configuration directive string, a string of 1 to 300 characters. This argument can be an AT directive (containing +++, A/, or be any string beginning with AT) or a CNS directive. For more information about AT directives, see the sendat command in Layer 2—WAN Access Command Reference. Table 4 describes the CNS directive samples. The format of this argument depends on the modem model.

Table 4 CNS directive description

Directive	Description
CNSn	Controls the CNS heartbeat debugging switch. · n = 00000500000000000000—Enables CNS heartbeat debugging. · n = 00000800000000000000—Disables CNS heartbeat debugging.

Directive

Description

CNSn

Controls the CNS heartbeat debugging switch.

· n = 00000500000000000000—Enables CNS heartbeat debugging.

· n = 00000800000000000000—Disables CNS heartbeat debugging.

Usage guidelines

The sendat command does not verify the configuration directive. Each time it issues one configuration directive to the mobile communication modem, lowercase characters are automatically converted to uppercase characters.

One sendat command issues one configuration directive. To issue multiple configuration directives to a modem, you must repeat the sendat command.

Configuration directives might cause malfunction of a mobile communication modem. When you issue a configuration directive to the modem, make sure you understand the impact on the mobile communication modem.

Examples

# Issue the ATD169 directive to the mobile communication modem to call number 169.

<Sysname> system-view

[Sysname] controller cellular 2/4/0

[Sysname-Cellular2/4/0] sendat ATD169

# Issue the cns00000500000000000000 directive to the mobile communication modem to enable CNS heartbeat debugging.

<Sysname> system-view

[Sysname] controller cellular 2/4/0

[Sysname-Cellular2/4/0] sendat cns00000500000000000000

shutdown

Use shutdown to shut down a cellular interface.

Use undo shutdown to bring up a cellular interface.

Syntax

shutdown

undo shutdown

Default

The cellular interface is up.

Views

Cellular interface view

Predefined user roles

network-admin

Examples

# Shut down Cellular 2/4/0.

<Sysname> system-view

[Sysname] interface cellular 2/4/0

[Sysname-Cellular2/4/0] shutdown

sim backup enable track

Use sim backup enable track to associate mobile communication link backup with a track entry.

Use undo sim backup enable to restore the default.

Syntax

sim backup enable track entry-number

undo sim backup enable

Default

Mobile communication link backup is not associated with a track entry.

Views

Cellular interface view

Predefined user roles

network-admin

Parameters

entry-number: Specifies a track entry by its ID in the range of 1 to 1024.

Usage guidelines

This command uses a track entry to monitor the status of the primary mobile communication link. When the track entry state changes from Positive to Negative, the secondary mobile communication link takes over. For information about track entries, see track configuration in High Availability Configuration Guide.

You can associate only one track entry with a mobile communication link. If you execute this command multiple times, the most recent configuration takes effect.

The association takes effect only after the track entry is created.

Examples

# Associate Cellular 1/0 with track entry 1.

<sysname> system

[system] controller cellular 1/0

[system-Cellular1/0] sim backup enable track 1

Related commands

sim switch-back enable

sim switch-to

sim switch-back enable

Use sim switch-back enable to enable automatic switchback to the primary SIM card.

Use undo sim switch-back enable to disable automatic switchback to the primary SIM card.

Syntax

sim switch-back enable [ wait-time time ]

undo sim switch-back enable

Default

Automatic switchback to the primary SIM card is disabled.

Views

Cellular interface view

Predefined user roles

network-admin

Parameters

time: Specifies the length of time for using the secondary SIM card. The value is in the range of 1 to 65535, in minutes. The default value is 60. After the time expires, the device automatically switches back to the primary SIM card.

Usage guidelines

This command allows the device to automatically switch back to the primary SIM card after the specified length of time for using the secondary SIM card. To avoid frequent primary/secondary switchovers, make sure the link of the primary SIM card can recover after the specified length of time.

Examples

# Enable the device to automatically switch back to the primary SIM card after 100 minutes of using the secondary SIM card.

<Sysname> system-view

[Sysname] controller cellular 1/0

[Sysname-Cellular1/0] sim switch-back enable wait-time 100

sim switch-to

Use sim switch-to to specify the primary or secondary SIM card.

Syntax

sim switch-to card-number

Default

The primary SIM card is used.

Views

Cellular interface view

Predefined user roles

network-admin

Parameters

card-number: Specifies a SIM card by its slot number. The value is 0 or 1. 0 represents the primary SIM card. 1 represents the secondary SIM card.

Usage guidelines

CAUTION:

This command might cause traffic interruption. Be aware of the impact of this command before executing it.

On a device that uses dual SIM card, you can execute this command to specify the use of the secondary SIM card when one of the following problems occurs:

· The mobile communication link signals of the primary SIM card are weak.

· The service provider network that the primary SIM card connects to is unavailable.

· The primary SIM card has failed.

If the problems of the primary SIM card are resolved, you can use this command to specify the use of the primary SIM card.

Examples

# Specify the secondary SIM card for the device.

<Sysname> system-view

[Sysname] controller cellular 1/0

[Sysname-Cellular1/0] sim switch-to 1

trust-imsi

Use trust-imsi to configure a trusted IMSI.

Use undo trust-imsi to remove a trusted IMSI.

Syntax

trust-imsi string-imsi

undo trust-imsi [ string-imsi ]

Default

No trusted IMSI is configured.

Views

Cellular interface view

Predefined user roles

network-admin

Parameters

string-imsi: Specifies an IMSI. The string-imsi argument is a case-insensitive string of 1 to 31 characters.

Usage guidelines

For a successful dialup, configure the IMSI of the SIM card as a trusted IMSI.

You can configure a maximum of 16 trusted IMSIs.

Examples

# Configure trusted IMSI hccc123456789 for Cellular 0/0.

<Sysname> system-view

[Sysname] controller cellular 0/0

[Sysname-Cellular0/0] trust-imsi hccc123456789

wcdma band

Use wcdma band to specify a WCDMA band.

Use undo wcdma band to restore the default.

Syntax

wcdma band { wcdma800 | wcdma850 | wcdma900 | wcdma1700ip | wcdma1700us | wcdma1800 | wcdma1900 | wcdma2100 | wcdma2600 }

undo wcdma band

Default

No WCDMA band is specified.

Views

Cellular interface view

Predefined user roles

network-admin

Parameters

wcdma800: Specifies the WCDMA 800 MHz band.

wcdma850: Specifies the WCDMA 850 MHz band.

wcdma900: Specifies the WCDMA 900 MHz band.

wcdma1700jp: Specifies the Japan WCDMA 1700 MHz band.

wcdma1700us: Specifies the US WCDMA 1700 MHz band.

wcdma1800: Specifies the WCDMA 1800 MHz band.

wcdma1900: Specifies the WCDMA 1900 MHz band.

wcdma2100: Specifies the WCDMA 2100 MHz band.

wcdma2600: Specifies the WCDMA 2600 MHz band.

Usage guidelines

Multiple frequency bands are available for accessing the WCDMA network. When the network environment changes, the modem might change the working band automatically to adapt to the change. To avoid link instability caused by frequency changes, you can specify a WCDMA band for the modem.

Examples

# Specify the WCDMA 1700 MHz band for the modem.

<Sysname> system-view

[Sysname] controller cellular 0/0

[Sysname-Cellular0/0] wcdma band wcdma1700

Related commands

gsm band

lte band

5G modem-specific management commands

apn

Use apn to specify an access point name (APN) for a 5G modem.

Use undo apn to remove an APN.

Syntax

apn { dynamic | static apn }

undo apn

Default

No APN is specified for a 5G modem.

Views

5G modem profile view

Predefined user roles

network-admin

Parameters

dynamic: Uses an APN automatically assigned by the service provider.

static apn: Specifies the APN provided by the service provider. The apn argument is a string of 1 to 100 characters. Whether the string is case-sensitive depends on the service provider.

Examples

# Specify APN apn1 for 5G modem profile test.

<Sysname> system-view

[Sysname] apn-profile test

[Sysname-apn-profile-test] apn static apn1

Related commands

apn-profile

Use apn-profile to create a 5G modem profile.

Use undo apn-profile to remove a 5G modem profile.

Syntax

apn-profile profile-name

undo apn-profile profile-name

Default

No 5G modem profile exists.

Views

System view

Predefined user roles

network-admin

Parameters

profile-name: Specifies a 5G modem profile name.

Usage guidelines

A 5G modem profile takes effect only after you apply the profile to an Eth-channel interface. To remove a 5G modem profile, you must first cancel the application.

Examples

# Create 5G modem profile test.

<Sysname> system-view

[Sysname] apn-profile test

Related commands

apn-profile apply

Use apn-profile apply to specify 5G modem profiles for an Eth-channel interface.

Use undo apn-profile apply to restore the default.

Syntax

apn-profile apply profile-name [ backup profile-name ]

undo apn-profile apply

Default

No 5G modem profiles are specified for an Eth-channel interface.

Views

Eth-channel interface view

Predefined user roles

network-admin

Parameters

profile-name: Specifies a primary 5G modem profile name.

backup profile-name: Specifies a backup 5G modem profile name.

Usage guidelines

After you specify a 5G modem profile for a 5G modem, the 5G modem uses the settings in the profile to negotiate with the service provider's device.

A primary profile always has priority over a backup profile. For each dialup connection establishment, the 5G modem uses the backup profile only when it has failed to dial up using the primary profile.

This command takes effect only on dialup connections initiated after the command is configured. It does not take effect on a dialup connection that has been established.

Examples

# Specify primary 5G modem profile test and backup 5G modem profile bktest for Eth-channel interface 2/4/0:0.

<Sysname> system-view

[Sysname] interface eth-channel 2/4/0:0

[Sysname-Eth-channel2/4/0:0] apn-profile apply test backup bktest

Related commands

apn-profile

attach-format imsi-sn split

Use attach-format imsi-sn split to specify a delimiter for the IMSI/SN binding authentication information.

Use undo attach-format imsi-sn split to restore the default.

Syntax

attach-format imsi-sn split splitchart

undo attach-format imsi-sn split

Default

No delimiter is specified for the IMSI/SN binding authentication information.

Views

5G modem profile view

Predefined user roles

network-admin

Parameters

split splitchart: Specifies a delimiter. It can be a letter, a digit, or a sign such as a percent sign (%) or a pound sign (#).

Usage guidelines

If IMSI/SN binding authentication is enabled, the IMSI/SN information is included in the authentication information in addition to the username. You need to configure a delimiter to separate different types of information. For example, if you specify the delimiter as #, the authentication information will be sent in the imsiinfo#sninfo#username format.

Examples

# Configure the pound sign (#) as the delimiter for the IMSI/SN binding authentication information.

<Sysname> system-view

[Sysname] apn-profile test

[Sysname-apn-profile-test] attach-format imsi-sn split #

Related commands

apn-profile

authentication-mode

Use authentication-mode to specify an authentication mode for accessing a 5G network.

Use undo authentication-mode to restore the default.

Syntax

authentication-mode { pap | chap| pap-chap } user user-name password { cipher | simple } string

undo authentication-mode

Default

No authentication mode is specified for accessing a 5G network.

Views

5G modem profile view

Predefined user roles

network-admin

Parameters

chap: Specifies CHAP authentication.

pap: Specifies PAP authentication.

pap-chap: Specifies CHAP or PAP authentication.

user username: Specifies the username for authentication, a case-sensitive string of 1 to 32 characters.

cipher: Specifies a password in encrypted form.

simple: Specifies a password in plaintext form. For security purposes, the password specified in plaintext form will be stored in encrypted form.

string: Specifies the password. Its plaintext form is a case-sensitive string of 1 to 32 characters. Its encrypted form is a case-sensitive string of 1 to 73 characters.

Examples

# Specify the CHAP authentication mode for 5G modem profile test. Specify the username as user1 and the password as 123456.

<Sysname> system-view

[Sysname] apn-profile test

[Sysname-apn-profile-test] authentication-mode chap user user1 password simple 123456

Related commands

apn-profile

bandwidth

Use bandwidth to configure the expected bandwidth for an Eth-channel interface.

Use undo bandwidth to restore the default.

Syntax

bandwidth bandwidth-value

undo bandwidth

Default

The expected bandwidth (in kbps) is the interface baud rate divided by 1000.

Views

Eth-channel interface view

Predefined user roles

network-admin

Parameters

bandwidth-value: Specifies the expected bandwidth in the range of 1 to 400000000 kbps.

Usage guidelines

The expected bandwidth for an interface affects the link costs in OSPF, OSPFv3, and IS-IS. For more information, see Layer 3—IP Routing Configuration Guide.

Examples

# Set the expected bandwidth for Eth-channel 2/4/0:0 to 1000 kbps.

<Sysname> system-view

[Sysname] interface eth-channel 2/4/0:0

[Sysname-Eth-channel2/4/0:0] bandwidth 1000

default

Use default to restore the default settings for an interface.

Syntax

default

Views

Eth-channel interface view

Predefined user roles

network-admin

Usage guidelines

CAUTION:

The default command might interrupt ongoing network services. Make sure you are fully aware of the impact of this command before using it on a live network.

This command might fail to restore the default settings for some commands for reasons such as command dependencies and system restrictions. Use the display this command in interface view to identify these commands. Then, use their undo forms or follow the command reference to individually restore their default settings. If your restoration attempt fails, follow the error message instructions to resolve the problem.

Examples

# Restore the default settings for Eth-channel 2/4/0:0.

<Sysname> system-view

[Sysname] interface eth-channel 2/4/0:0

[Sysname-Eth-channel2/4/0:0] default

description

Use description to configure the description of an interface.

Use undo description to restore the default.

Syntax

description text

undo description

Default

The description for an interface is in the interface name Interface format, for example, Echannel2/4/0:0 Interface.

Views

Eth-channel interface view

Predefined user roles

network-admin

Parameters

text: Sets an interface description, a case-sensitive string of 1 to 255 characters.

Usage guidelines

Configure the description of an interface for easy identification and management purposes.

You can use the display interface command to view the description for an interface.

Examples

# Configure the description for Eth-channel 2/4/0:0 as Echannel-interface.

<Sysname> system-view

[Sysname] interface eth-channel 2/4/0:0

[Sysname-Eth-channel2/4/0:0] description Echannel-interface

display interface eth-channel

Use display interface eth-channel to display information about the specified or all Eth-channel interfaces.

Syntax

display interface [ eth-channel [ channel-id ] ] [ brief [ description | down ] ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

eth-channel [ channel-id ]: Specifies Eth-channel interfaces or an Eth-channel interface by its number. If you do not specify the eth-channel keyword, the command displays information about all interfaces. If you specify the eth-channel keyword but not the channel-id argument, this command displays information about all Eth-channel interfaces.

brief: Displays brief interface information. If you do not specify this keyword, the command displays detailed interface information.

description: Displays complete interface descriptions. If you do not specify this keyword, the command displays only the first 27 characters of interface descriptions.

down: Displays information about interfaces in down state and the causes. If you do not specify this keyword, the command displays information about interfaces in all states.

Examples

# Display detailed information about Eth-channel 2/4/0:0, including its operating status.

<Sysname> display interface eth-channel 2/4/0:0

Echannel2/4/0:0

Current state: DOWN

Line protocol state: DOWN

Description: Echannel2/4/0:0 Interface

Bandwidth: 100000kbps

Maximum Transmit Unit: 1500

Internet protocol processing: disabled

IP Packet Frame Type:PKTFMT_ETHNT_2, Hardware Address: 000c-2963-b75d

IPv6 Packet Frame Type:PKTFMT_ETHNT_2, Hardware Address: 000c-2963-b75d

Output queue - Urgent queuing: Size/Length/Discards 0/100/0

Output queue - Protocol queuing: Size/Length/Discards 0/500/0

Output queue - FIFO queuing: Size/Length/Discards 0/75/0

Last link flapping: Never

Last clearing of counters: Never

Last 300 seconds input rate 0.00 bytes/sec, 0.00 packets/sec

Last 300 seconds output rate 0.00 bytes/sec, 0.00 packets/sec

Input: 0 packets, 0 bytes, 0 buffers

Output:0 packets, 0 bytes

# Display brief information about Eth-channel 2/4/0:0.

<Sysname> display interface eth-channel 2/4/0:0 brief

Brief information on interface(s) under route mode:

Link: ADM - administratively down; Stby - standby

Protocol: (s) - spoofing

Interface Link Protocol Main IP Description

Echannel2/4/0:0 UP UP(s) 192.168.80.239

# Display information about all Eth-channel interfaces in down state and the causes.

<Sysname> display interface eth-channel brief down

Brief information on interface(s) under route mode:

Link: ADM - administratively down; Stby - standby

Interface Link Cause

Echannel2/4/0:0 ADM Administratively

Table 5 Command output

Field	Description
Current state	Physical link state of the interface: · Administratively DOWN—The interface has been shut down by using the shutdown command. · DOWN—The interface is administratively up, but its physical state is down (possibly because no physical link exists or the link has failed). · UP—The interface is both administratively and physically up.
Line protocol state	Data link layer state of the interface. The state is determined through automatic parameter negotiation at the data link layer. · UP—The data link layer protocol is up. · UP (spoofing)—The data link layer protocol is up, but the link is an on-demand link or does not exist. This attribute is typical of null interfaces and loopback interfaces. · DOWN—The data link layer protocol is down.
Description	Description for the interface.
Bandwidth	Expected bandwidth of the interface.
Maximum Transmit Unit	MTU of the interface.
Internet address: ip-address/mask-length (Type)	IP address of the interface and type of the address in parentheses. Possible IP address types include: · Primary—Manually configured primary IP address. · Sub—Manually configured secondary IP address. If the interface has both primary and secondary IP addresses, the primary IP address is displayed. If the interface has only secondary IP addresses, the lowest secondary IP address is displayed. · DHCP-allocated—DHCP allocated IP address. For more information, see DHCP client configuration in Layer 3—IP Services Configuration Guide. · BOOTP-allocated—BOOTP allocated IP address. For more information, see BOOTP client configuration in Layer 3—IP Services Configuration Guide. · PPP-negotiated—IP address assigned by a PPP server during PPP negotiation. For more information, see PPP configuration in Layer 2—WAN Access Configuration Guide. · Unnumbered—IP address borrowed from another interface. · Cellular-allocated—IP address allocated through the modem-manufacturer's proprietary protocol. For more information, see mobile communication modem management in Layer 2—WAN Access Configuration Guide. · MTunnel—IP address of the multicast tunnel interface (MTI), which is the same as the IP address of the MD source interface. For more information, see multicast VPN configuration in IP Multicast Configuration Guide.
Internet protocol processing: disabled	The interface is not assigned an IP address and cannot process IP packets.
Internet Address is 192.168.1.200/24 Primary	IP address of the interface. The primary attribute indicates that the address is the primary IP address..
IP Packet Frame Type	IPv4 packet framing format.
Hardware Address	MAC address of the interface.
IPv6 Packet Frame Type	IPv6 packet framing format.
Output queue - Urgent queuing: Size/Length/Discards	Packet statistics for urgent queuing in the output queue of the interface: · Size—Current number of packets in the queue. · Length—Maximum number of packets that can stay in the queue. · Discards—Number of dropped packets.
Output queue - Protocol queuing: Size/Length/Discards	Packet statistics for protocol queuing in the output queue of the interface: · Size—Current number of packets in the queue. · Length—Maximum number of packets that can stay in the queue. · Discards—Number of dropped packets.
Output queue - FIFO queuing: Size/Length/Discards	Packet statistics for FIFO queuing in the output queue of the interface: · Size—Current number of packets in the queue. · Length—Maximum number of packets that can stay in the queue. · Discards—Number of dropped packets.
Last link flapping	The amount of time that has elapsed since the most recent physical state change of the interface. This field displays Never if the interface has been physically down since device startup.
Last clearing of counters	Time when statistics on the logical interface were last cleared by using the reset counters interface command. If the statistics of the interface have never been cleared by using the reset counters interface command since the device started, this field displays Never.
Last 300 seconds input rate	Average input rate during the last 300 seconds: · bytes/sec—Average number of received bytes per second. · bits/sec—Average number of received bits per second. · packets/sec—Average number of received packets per second.
Last 300 seconds output rate	Average output rate over the last 300 seconds: · bytes/sec—Average number of sent bytes per second. · bits/sec—Average number of sent bits per second. · packets/sec—Average number of sent packets per second.
Input: 0 packets, 0 bytes, 0 buffers	Incoming packet statistics: · 0 packets—Packet number. · 0 bytes—Packet size in bytes. · 0 buffers—Number of buffered units.
Output: 0 packets, 0 bytes	Outgoing packet statistics: · 0 packets—Packet number. · 0 bytes—Packet size in bytes.
Link	Physical link state of the interface: · UP—The interface is physically up. · DOWN—The interface is physically down. · ADM—The interface has been shut down by using the shutdown command. To restore the physical state of the interface, use the undo shutdown command. · Stby—The interface is a backup interface in standby state. To see the primary interface, use the display interface-backup state command.
Protocol	Data link layer protocol state of the interface: · UP—The data link layer protocol of the interface is up. · DOWN—The data link layer protocol of the interface is down. · UP(s)—The data link layer protocol of the interface is up, but the link is an on-demand link or does not exist. The (s) attribute represents the spoofing flag. This value is typical of null interfaces and loopback interfaces.
Main IP	Main IP address of the interface.
Description	Description of the interface.
Cause	Cause for the physical link state of the interface to be DOWN. Administratively represents that the interface has been manually shut down by using the shutdown command. To restore the physical state of the interface, use the undo shutdown command.

eth-channel

Use eth-channel to channelize a cellular interface into an Eth-channel interface.

Use undo eth-channel to remove the Eth-channel interface channelized from a cellular interface.

Syntax

eth-channel channel-number

undo eth-channel channel-number

Views

Cellular interface view

Predefined user roles

network-admin

Parameters

channel-number: Specifies an Eth-channel interface by its number. The value range for this argument varies by modem model.

Usage guidelines

This command names the Eth-channel interface channelized from a cellular interface as eth-channel cellular-number:channel-number.

Examples

# Channelize Cellular 2/4/0 into an Eth-channel interface.

<Sysname> system-view

[Sysname] controller cellular 2/4/0

[Sysname-Cellular2/4/0] eth-channel 0

imsi bind

Use imsi bind to bind the IMSI on the SIM card to an interface.

Use undo imsi bind to restore the default.

Syntax

imsi bind interface-type interface-number

undo imsi bind

Default

The IMSI on the SIM card is not bound to any interface.

Views

Cellular interface view

Predefined user roles

network-admin

Parameters

interface-type interface-number: Specifies an interface by its type and number. In the current software version, the IMSI on the SIM card can only be bound to an L2TP virtual PPP interface.

Usage guidelines

This command is not available for distributed devices or devices operating in IRF mode.

A 5G router must support PPP LCP negotiation of the IMSI/SI when it acts as a LAC to access the LNS in LAC-auto-initiated mode. After you bind the IMSI on the SIM card to a virtual PPP interface, the packets sent by the router carry the IMSI.

Examples

# Bind the IMSI on the SIM card to Virtual-PPP 1.

<Sysname> system-view

[Sysname] controller Cellular 0/0

[Sysname-Cellular0/0] imsi bind virtual-ppp 1

interface eth-channel

Use interface eth-channel to enter Eth-channel interface view.

Syntax

interface eth-channel interface-number

Views

System view

Predefined user roles

network-admin

Parameters

interface-number: Specifies an Eth-channel interface by its number.

Examples

# Enter Eth-channel 2/4/0:0 interface view.

<Sysname> system-view

[Sysname] interface eth-channel 2/4/0:0

[Sysname-Eth-channel2/4/0:0]

ip address cellular-alloc

Use ip address cellular-alloc to enable an Eth-channel interface to obtain an IP address by using the modem-manufacturer's proprietary protocol.

Use undo ip address cellular-alloc to restore the default.

Syntax

ip address cellular-alloc

undo ip address cellular-alloc

Default

An Eth-channel interface does not obtain an IP address by using the modem-manufacturer's proprietary protocol.

Views

Eth-channel interface view

Predefined user roles

network-admin

Usage guidelines

To enable an interface to obtain an IP address from the modem by using the modem-manufacturer's proprietary protocol, use the ip address cellular-alloc command.

To enable an interface to obtain an IP address from the modem by using DHCP, use the ip address dhcp-alloc command.

The IP address of the modem is automatically allocated by the service provider.

Examples

# Channelize Cellular 2/4/0 into an Eth-channel interface. Enable the Eth-channel interface to obtain an IP address by using the modem-manufacturer's proprietary protocol.

<Sysname> system-view

[Sysname] controller cellular 2/4/0

[Sysname-Cellular2/4/0] eth-channel 0

[Sysname-Cellular2/4/0] quit

[Sysname] interface eth-channel 2/4/0:0

[Sysname-Eth-channel2/4/0:0] ip address cellular-alloc

ipv6 address cellular-alloc

Use ipv6 address cellular-alloc to enable an interface to obtain an IPv6 address by using the modem-manufacturer's proprietary protocol.

Use undo ipv6 address cellular-alloc to restore the default.

Syntax

ipv6 address cellular-alloc

undo ipv6 address cellular-alloc

Default

An interface does not obtain an IPv6 address by using the modem-manufacturer's proprietary protocol.

Views

Eth-channel interface view

Predefined user roles

network-admin

Usage guidelines

To enable an interface to obtain an IPv6 address by using the modem-manufacturer's proprietary protocol, use the ipv6 address cellular-alloc command.

To enable an interface to obtain an IP address by using DHCP, use the ipv6 address dhcp-alloc command.

The IPv6 address of the modem is automatically allocated by the service provider.

Examples

# Channelize Cellular 2/4/0 into an Eth-channel interface. Enable the Eth-channel interface to obtain an IPv6 address by using the modem-manufacturer's proprietary protocol.

<Sysname> system-view

[Sysname] controller cellular 2/4/0

[Sysname-Cellular2/4/0] eth-channel 0

[Sysname-Cellular2/4/0] quit

[Sysname] interface eth-channel 2/4/0:0

[Sysname-Eth-channel2/4/0:0] ipv6 address cellular-alloc

Related commands

ip address cellular-alloc

lte band

Use lte band to specify a band for a 5G modem.

Use undo lte band to restore the default.

Syntax

lte band band-number

undo lte band

Default

The default setting for this command varies by modem model.

Views

Cellular interface view

Predefined user roles

network-admin

Parameters

band-number: Specifies a band for a modem. The available bands vary by modem model.

Examples

# Specify band 3 for Cellular 2/4/0.

<Sysname> system-view

[Sysname] controller cellular 2/4/0

[Sysname-Controller-Cellular2/4/0] lte band 3

mtu

Use mtu to set the maximum transmission unit (MTU) for an interface.

Use undo mtu to restore the default.

Syntax

mtu size

undo mtu

Default

The MTU of an interface is 1500 bytes.

Views

Eth-channel interface view

Predefined user roles

network-admin

Parameters

size: Sets the MTU in bytes. The value range for this argument varies by modem model.

Examples

# Set the MTU for Eth-channel 2/4/0:0 to 1430 bytes.

<Sysname> system-view

[Sysname] interface eth-channel 2/4/0:0

[Sysname-Eth-channel2/4/0:0] mtu 1430

nr band

Use nr band to specify a 5G NR frequency band.

Use undo nr band to restore the default.

Syntax

nr band nr-band-number

undo nr band

Default

The default setting of this command varies by modem model.

Views

Cellular interface view

Predefined user roles

network-admin

Parameters

nr-band-number: Specifies a 5G NR frequency band. The value range varies by modem model.

Examples

# Specify NR frequency band 3 for Cellular 2/4/0.

<Sysname> system-view

[Sysname] controller cellular 2/4/0

[Sysname-Controller-Cellular2/4/0] nr band n3

Related commands

gsm band

lte band

wcdma band

nr mode

Use nr mode to specify the 5G new radio (NR) network deployment mode for 5G modem network registration.

Use undo nr mode to restore the default.

Syntax

nr mode { nsa | sa | auto }

undo nr mode

Default

A 5G modem registers with a 5G NR network deployed in SA mode preferentially than that deployed in NSA mode.

Views

Cellular interface view

Predefined user roles

network-admin

Parameters

nsa: Specifies the NSA 5G NR network deployment mode for 5G modem network registration.

sa: Specifies the SA 5G NR network deployment mode for 5G modem network registration.

auto: Enables the 5G modem to register with a 5G NR network deployed in SA mode preferentially than that deployed in NSA mode.

Examples

# Specify the NSA 5G network deployment mode for 5G modem network registration.

<Sysname> system-view

[Sysname] controller cellular 0/0

[Sysname-Cellular0/0]nr mode nsa

pdp-type

Use pdp-type to specify the PDP data carrying protocol.

Use undo pdp-type to restore the default.

Syntax

pdp-type { ipv4 | ipv6 | ipv4v6 }

undo pdp-type

Default

The PDP data carrying protocol is IPv4 and IPv6.

Views

Apn-profile view

Predefined user roles

network-admin

Parameters

ipv4: Specifies the IPv4 protocol.

ipv6: Specifies the IPv6 protocol.

ipv4v6: Specifies the IPv4 and IPv6 protocols.

Examples

# Specify the PDP data carrying protocol as IPv4.

<Sysname> system-view

[Sysname] apn-profile 1

[Sysname-apn-profile-1] pdp-type ipv4

reset counters interface

Use reset counters interface to clear the statistics on the specified or all Eth-channel interfaces.

Syntax

reset counters interface [ eth-channel [ channel-id ] ]

Views

User view

Predefined user roles

network-admin

Parameters

eth-channel [ channel-id ]: Specifies Eth-channel interfaces or an Eth-channel interface by its number. If you do not the eth-channel keyword, the command clears statistics on all interfaces. If you specify the eth-channel keyword but not the channel-id argument, this command clears statistics on all Eth-channel interfaces. If you specify both the eth-channel keyword and the channel-id argument, this command clears statistics on the specified Eth-channel interface.

Usage guidelines

Use this command to clear history statistics if you want to collect traffic statistics for a specific period.

Examples

# Clear the statistics on Eth-channel 2/4/0:0.

<Sysname> reset counters interface eth-channel 2/4/0:0

shutdown

Use shutdown to shut down an Eth-channel interface.

Use undo shutdown to bring up an Eth-channel interface.

Syntax

shutdown

undo shutdown

Default

The default setting for this command depends on the modem model.

Views

Eth-channel interface view

Predefined user roles

network-admin

Examples

# Shut down Eth-channel 2/4/0:0.

<Sysname> system-view

[Sysname] interface eth-channel 2/4/0:0

[Sysname-Eth-channel2/4/0:0] shutdown

06-Layer 2—WAN Access Command Reference

description

sim backup enable track

display interface eth-channel

Cloud & AI

InterConnect

Intelligent Terminal Products

Product Support Services

Technical Service Solutions

Resource Center

Policy

Online Help

Become a Partner

Partner Resources

Partner Business Management

Company Information

News & Events

Contact Us