07-AP and WT Management Command Reference

HomeSupportResource CenterReference GuidesCommand ReferencesH3C Access Controllers Command References(R5447P04)-6W10007-AP and WT Management Command Reference
02-WT commands
Title Size Download
02-WT commands 57.07 KB

WT commands

The AP models and serial numbers in this document are used only as examples. Support for AP models and serial numbers depends on the AC model.

The following compatibility matrixes show the support of hardware platforms for WT:

 

Hardware series

Model

Product code

WT compatibility

WX1800H series

WX1804H-PWR

EWP-WX1804H-PWR-CN

No

WX2500H series

WX2508H-PWR-LTE

WX2510H-PWR

WX2510H-F-PWR

WX2540H

WX2540H-F

WX2560H

EWP-WX2508H-PWR-LTE

EWP-WX2510H-PWR

EWP-WX2510H-F-PWR

EWP-WX2540H

EWP-WX2540H-F

EWP-WX2560H

Yes

MAK series

MAK204

MAK206

EWP-MAK204

EWP-MAK206

No

WX3000H series

WX3010H

WX3010H-X-PWR

WX3010H-L-PWR

WX3024H

WX3024H-L-PWR

WX3024H-F

EWP-WX3010H

EWP-WX3010H-X-PWR

EWP-WX3010H-L-PWR

EWP-WX3024H

EWP-WX3024H-L-PWR

EWP-WX3024H-F

Yes

WX3500H series

WX3508H

WX3508H

WX3510H

WX3510H

WX3520H

WX3520H-F

WX3540H

WX3540H

EWP-WX3508H

EWP-WX3508H-F

EWP-WX3510H

EWP-WX3510H-F

EWP-WX3520H

EWP-WX3520H-F

EWP-WX3540H

EWP-WX3540H-F

Yes

WX5500E series

WX5510E

WX5540E

EWP-WX5510E

EWP-WX5540E

Yes

WX5500H series

WX5540H

WX5560H

WX5580H

EWP-WX5540H

EWP-WX5560H

EWP-WX5580H

Yes

Access controller modules

LSUM1WCME0

EWPXM1WCME0

LSQM1WCMX20

LSUM1WCMX20RT

LSQM1WCMX40

LSUM1WCMX40RT

EWPXM2WCMD0F

EWPXM1MAC0F

LSUM1WCME0

EWPXM1WCME0

LSQM1WCMX20

LSUM1WCMX20RT

LSQM1WCMX40

LSUM1WCMX40RT

EWPXM2WCMD0F

EWPXM1MAC0F

Yes

Hardware series

Model

Product code

WT compatibility

WX1800H series

WX1804H-PWR

WX1810H-PWR

WX1820H

WX1840H

EWP-WX1804H-PWR

EWP-WX1810H-PWR

EWP-WX1820H

EWP-WX1840H-GL

No

WX3800H series

WX3820H

WX3840H

EWP-WX3820H-GL

EWP-WX3840H-GL

No

WX5800H series

WX5860H

EWP-WX5860H-GL

No

display wlan wt

Use display wlan wt to display wireless terminator (WT) information and information about the wireless terminator units (WTUs) connected to it.

Syntax

display wlan wt { all | name wt-name }

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

all: Specifies all WTs.

name wt-name: Specifies a WT by its name, a case-sensitive string of 1 to 64 characters. The string can contain letters, digits, underscores (_), dots (.), left brackets ([), right brackets (]), forward slashes (/), and hyphens (-).

Examples

# Display information about all WTs.

<Sysname> display wlan wt all

WT name          : wt1

Model            : WT1020

Serial ID        : 219801A0SS9156G00072

MAC address      : 0000-f3ea-0a3e

WTU number       : 2

  Wireless Terminator Unit:

  ---------------------------------------------------------

  WTU name      Port         Model      Serial ID

  ---------------------------------------------------------

  wtu1          1            WTU430     219801A0SS9156G00185

  wtu2          2            WTU430     219801A0SS9156G00133

 

WT name          : wt2

Model            : WT1020

Serial ID        : 219801A0SS9156G00068

MAC address      : 0000-f3ea-0a3a

WTU number       : 2

Wireless Terminator Unit:

  ---------------------------------------------------------

  WTU name      Port         Model      Serial ID

  ---------------------------------------------------------

  wtu3          3            WTU430     219801A0SS9156G00054

  Wtu4          4            WTU430     219801A0SS9156G00167

Table 1 Command output

Fields

Description

WTU number

Number of WTUs that are connected to the WT.

Wireless Terminator Unit

WTU information.

Port

Port that connects the WT to a WTU.

 

poe wtu-port

Use poe wtu-port enable to enable PoE for a WTU port.

Use poe wtu-port disable to disable PoE for a WTU port.

Use undo poe wtu-port to restore the default.

Syntax

poe wtu-port port-number1 [ to port-number2 ] { disable | enable }

undo poe wtu-port port-number1 [ to port-number2 ]

Default

In AP view, an AP uses the configuration in an AP group's AP model view.

In an AP group's AP model view, PoE is enabled for WTU ports.

Views

AP view

AP group's AP model view

Predefined user roles

network-admin

Parameters

port-number1: Specifies the WTU port number. The value range varies by WT model.

port-number1 to port-number2: Specifies a WTU port range. The port-number1 argument represents the start port number, and the port-number2 argument represents the end port number. The end port number cannot be smaller than the start port number. Value range for a port number varies by WT model.

Usage guidelines

A WT stops power supply to the connected WTU through PoE after you disable PoE for a WTU port of the WT.

This command is configurable only when the AP is a WT.

Examples

# Disable PoE for WTU port 1 in AP view.

<Sysname> system-view

[Sysname] wlan ap ap1 model WT1020

[Sysname-wlan-ap-ap1] poe wtu-port 1 disable

# Disable PoE for WTU port 1 in AP model view of AP group 1.

<Sysname> system-view

[Sysname] wlan ap-group 1

[Sysname-wlan-ap-group-1] ap-model WT1020

[Sysname-wlan-ap-group-1-ap-model-WT1020] poe wtu-port 1 disable

port-type switch

 

NOTE:

Support for this command depends on the WT model.

 

Use port-type switch to enable switching between an Ethernet port and a WTU port on a WT.

Use undo port-type switch to restore the default.

Syntax

port-type switch number port-number-list { gigabitethernet | wtu }

undo port-type switch number port-number-list

Default

In AP view, an AP uses the configuration in an AP group's AP model view.

In an AP group's AP model view, the default setting varies by AP model.

Views

AP view

AP group's AP model view

Predefined user roles

network-admin

Parameters

gigabitethernet: Switches a WTU port to an Ethernet port.

wtu: Switches an Ethernet port to a WTU port.

port-number-list: Specifies a space-separated list of Ethernet or WTU port items. Each item specifies an Ethernet/WTU port or a range of Ethernet/WTU ports in the form of port-number1 to port-number2. The value for the port-number2 argument must be equal to or greater than the value for the port-number1 argument. &<1-n> Indicates that you can specify up to n port numbers. The value for n varies by WT model.

Usage guidelines

CAUTION

CAUTION:

To prevent the chips on the connected from being damaged because of PoE power supply capacity change, make sure the port to switch is not connected to any other device.

 

You can execute this command to increase the number of WTU ports on a WT.

This command will reboot the WT and the new port will use its default settings.

If a port has a mark of two different port names separated by a slash (/), G3/WTU26 for example, the port supports port type switching.

The configuration in AP view takes precedence over the configuration in an AP group's AP model view.

Examples

# Switch Ethernet port 2 to a WTU port in AP view.

<Sysname> system-view

[Sysname] wlan ap ap1 model WT1024-X-Q

[Sysname-wlan-ap-ap1] port-type switch number 2 wtu

# Switch Ethernet port 2 to a WTU port in AP model view of AP group 1.

<Sysname> system-view

[Sysname] wlan ap-group 1

[Sysname-wlan-ap-group-1] ap-model WT1024-X-Q

[Sysname-wlan-ap-group-1-ap-model-WT1024-X-Q] port-type switch number 2 wtu

wt version

 

NOTE:

Support for this command depends on the WT model.

 

Use wt version to specify the WT version.

Use undo wt version to restore the default.

Syntax

wt version { 1 | 2 | 3 }

undo wt version

Default

In AP view, an AP uses the configuration in an AP group's AP model view.

In an AP group's AP model view, the default setting varies by AP model.

Views

AP view

AP group's AP model view

Predefined user roles

network-admin

Parameters

1: Specifies version 1.0.

2: Specifies version 2.0.

3: Specifies version 3.0.

Usage guidelines

This command is configurable only when the AP is a WT.

If the specified WT version is different from the WT version in use, the WT will restart automatically. Then, it will switch to the specified WT version and restore the factory settings.

Support for WT versions varies by AP model.

This command does not take effect on WTs that support different types of WTUs.

Examples

# Specify version 2.0 as the WT version in AP view.

<Sysname> system-view

[Sysname] wlan ap ap1 mode WT1020

[Sysname-wlan-ap-ap1] wt version 2

# Specify version 2.0 as the WT version in AP model view of AP group 1.

<Sysname> system-view

[Sysname] wlan ap-group 1

[Sysname-wlan-ap-group-1] ap-model WT1020

[Sysname-wlan-ap-group-1-ap-model-WT1020] wt version 2

  • Cloud & AI
  • InterConnect
  • Intelligent Computing
  • Security
  • SMB Products
  • Intelligent Terminal Products
  • Product Support Services
  • Technical Service Solutions
All Services
  • Resource Center
  • Policy
  • Online Help
All Support
  • Become a Partner
  • Partner Resources
  • Partner Business Management
All Partners
  • Profile
  • News & Events
  • Online Exhibition Center
  • Contact Us
All About Us
新华三官网