Contents

Configuring static routing· 1

About static routes· 1

Configuring a static route· 1

Configuring a static route group· 1

Deleting static routes· 2

Configuring BFD for static routes· 3

About BFD·· 3

Configuring BFD control packet mode· 3

Configuring BFD echo packet mode· 4

Configuring static route FRR· 4

About static route FRR· 4

Restrictions and guidelines for static route FRR· 5

Configuring static route FRR by specifying a backup next hop· 5

Configuring static route FRR to automatically select a backup next hop· 6

Enabling BFD echo packet mode for static route FRR· 6

Display and maintenance commands for static routing· 6

Configuring a default route· 7

 

Configuring static routing

About static routes

Static routes are manually configured. If a network's topology is simple, you only need to configure static routes for the network to work correctly.

Static routes cannot adapt to network topology changes. If a fault or a topological change occurs in the network, the network administrator must modify the static routes manually.

Configuring a static route

1.     Enter system view.

system-view

2.     Configure a static route.

Public network:

ip route-static dest-address { mask-length | mask } { interface-type interface-number [ next-hop-address ] | next-hop-address | vpn-instance d-vpn-instance-name next-hop-address } [ permanent | track track-entry-number ] [ preference preference ] [ tag tag-value ] [ description text ]

By default, no static route is configured.

You can associate Track with a static route to monitor the reachability of the next hops. For more information about Track, see Network Management and Monitoring Configuration Guide.

VPN:

ip route-static vpn-instance s-vpn-instance-name dest-address { mask-length | mask } { interface-type interface-number [ next-hop-address ] | next-hop-address [ public ] | vpn-instance d-vpn-instance-name next-hop-address } [ permanent | track track-entry-number ] [ preference preference ] [ tag tag-value ] [ description text ]

By default, no static route is configured.

You can associate Track with a static route to monitor the reachability of the next hops. For more information about Track, see Network Management and Monitoring Configuration Guide.

3.     (Optional.) Configure the default preference for static routes.

ip route-static default-preference default-preference

The default setting is 60.

Configuring a static route group

About this task

This task allows you to batch create static routes with different prefixes but the same output interface and next hop.

You can create a static route group, and specify the static group in the ip route-static command. All prefixes in the static route group will be assigned the next hop and output interface specified in the ip route-static command.

Procedure

1.     Enter system view.

system-view

2.     Create a static route group and enter its view.

ip route-static-group group-name

By default, no static route group is configured.

3.     Add a static route prefix to the static route group.

prefix dest-address { mask-length | mask }

By default, no static route prefix is added to the static route group.

4.     Return to system view.

quit

5.     Configure a static route.

Public network:

ip route-static group group-name { interface-type interface-number [ next-hop-address ] | next-hop-address | vpn-instance d-vpn-instance-name next-hop-address } [ permanent | track track-entry-number ] [ preference preference ] [ tag tag-value ] [ description text ]

VPN:

ip route-static vpn-instance s-vpn-instance-name group group-name { interface-type interface-number [ next-hop-address ] | next-hop-address [ public ] | vpn-instance d-vpn-instance-name next-hop-address } [ permanent | track track-entry-number ] [ preference preference ] [ tag tag-value ] [ description text ]

By default, no static route is configured.

Deleting static routes

About this task

To delete a static route, use the undo ip route-static command. To delete all static routes including the default route, use the delete static-routes all command.

Procedure

1.     Enter system view.

system-view

2.     Delete all static routes.

Public network:

delete static-routes all

VPN:

delete vpn-instance vpn-instance-name static-routes all

‌

	CAUTION: This command might interrupt network communication and cause packet forwarding failure. Before executing the command, make sure you fully understand the potential impact on the network.

‌

Configuring BFD for static routes

	IMPORTANT: Enabling BFD for a flapping route could worsen the situation.

 

About BFD

BFD provides a general-purpose, standard, medium-, and protocol-independent fast failure detection mechanism. It can uniformly and quickly detect the failures of the bidirectional forwarding paths between two routers for protocols, such as routing protocols.

For more information about BFD, see Network Management and Monitoring Configuration Guide.

Configuring BFD control packet mode

About this task

This mode uses BFD control packets to detect the status of a link bidirectionally at a millisecond level.

BFD control packet mode can be applied to static routes with a direct next hop or with an indirect next hop.

Restrictions and guidelines for BFD control packet mode

If you use BFD control packet mode at the local end, you must use this mode also at the peer end.

Configuring BFD control packet mode for a static route (direct next hop)

1.     Enter system view.

system-view

2.     Configure BFD control packet mode for a static route.

Public network:

ip route-static dest-address { mask-length | mask } interface-type interface-number { next-hop-address } bfd { control-packet | static session-name } [ preference preference ] [ tag tag-value ] [ description text ]

VPN:

ip route-static vpn-instance s-vpn-instance-name dest-address { mask-length | mask } interface-type interface-number { next-hop-address } bfd { control-packet | static session-name } [ preference preference ] [ tag tag-value ] [ description text ]

By default, BFD control packet mode for a static route is not configured.

Configuring BFD control packet mode for a static route (indirect next hop)

1.     Enter system view.

system-view

2.     Configure BFD control packet mode for a static route.

Public network:

ip route-static dest-address { mask-length | mask } { next-hop-address bfd control-packet bfd-source ip-address | vpn-instance d-vpn-instance-name next-hop-address bfd { control-packet bfd-source ip-address | static session-name } } [ preference preference ] [ tag tag-value ] [ description text ]

VPN:

ip route-static vpn-instance s-vpn-instance-name dest-address { mask-length | mask } { next-hop-address bfd { control-packet bfd-source ip-address | static session-name } | vpn-instance d-vpn-instance-name next-hop-address bfd { control-packet bfd-source ip-address | static session-name } } [ preference preference ] [ tag tag-value ] [ description text ]

By default, BFD control packet mode for a static route is not configured.

Configuring BFD echo packet mode

About this task

With BFD echo packet mode enabled for a static route, the output interface sends BFD echo packets to the destination device, which loops the packets back to test the link reachability.

Restrictions and guidelines

You do not need to configure BFD echo packet mode at the peer end.

Do not use BFD for a static route with the output interface in spoofing state.

Procedure

1.     Enter system view.

system-view

2.     Configure the source address of echo packets.

bfd echo-source-ip ip-address

By default, the source address of echo packets is not configured.

For more information about this command, see Network Management and Monitoring Command Reference.

3.     Configure BFD echo packet mode for a static route.

Public network:

ip route-static dest-address { mask-length | mask } interface-type interface-number { next-hop-address } bfd { echo-packet | static session-name } [ preference preference ] [ tag tag-value ] [ description text ]

VPN:

ip route-static vpn-instance s-vpn-instance-name dest-address { mask-length | mask } interface-type interface-number { next-hop-address } bfd { echo-packet | static session-name } [ preference preference ] [ tag tag-value ] [ description text ]

By default, BFD echo packet mode for a static route is not configured.

Configuring static route FRR

About static route FRR

A link or router failure on a path can cause packet loss. Static route fast reroute (FRR) enables fast rerouting to minimize the impact of link or node failures.

Figure 1 Network diagram

 

As shown in Figure 1, upon a link failure, packets are directed to the backup next hop to avoid traffic interruption. You can either specify a backup next hop for FRR or enable FRR to automatically select a backup next hop (which must be configured in advance).

Restrictions and guidelines for static route FRR

Do not use static route FRR and BFD (for a static route) at the same time.

Equal-cost routes do not support static route FRR.

Besides the configured static route for FRR, the device must have another route to reach the destination. When the state of the primary link (with Layer 3 interfaces staying up) changes from bidirectional to unidirectional or down, static route FRR quickly redirects traffic to the backup next hop. When the Layer 3 interfaces of the primary link are down, static route FRR temporarily redirects traffic to the backup next hop. In addition, the device searches for another route to reach the destination and redirects traffic to the new path if a route is found. If no route is found, traffic interruption occurs.

Configuring static route FRR by specifying a backup next hop

Restrictions and guidelines

A static route does not take effect when the backup output interface is unavailable.

To change the backup output interface or next hop, you must first remove the current setting. The backup output interface and next hop must be different from the primary output interface and next hop.

Procedure

1.     Enter system view.

system-view

2.     Configure static route FRR.

Public network:

ip route-static dest-address { mask-length | mask } interface-type interface-number [ { next-hop-address } [ backup-interface interface-type interface-number [ backup-nexthop backup-nexthop-address ] ] ] [ permanent ] [ preference preference ] [ tag tag-value ] [ description text ]

VPN:

ip route-static vpn-instance s-vpn-instance-name dest-address { mask-length | mask } interface-type interface-number [ { next-hop-address } [ backup-interface interface-type interface-number [ backup-nexthop backup-nexthop-address ] ] ] [ permanent ] [ preference preference ] [ tag tag-value ] [ description text ]

By default, static route FRR is disabled.

Configuring static route FRR to automatically select a backup next hop

1.     Enter system view.

system-view

2.     Configure static route FRR to automatically select a backup next hop.

ip route-static fast-reroute auto

By default, static route FRR is disabled from automatically selecting a backup next hop.

Enabling BFD echo packet mode for static route FRR

About this task

By default, static route FRR uses ARP to detect primary link failures. Perform this task to enable static route FRR to use BFD echo packet mode for fast failure detection on the primary link.

Procedure

1.     Enter system view.

system-view

2.     Configure the source IP address of BFD echo packets.

bfd echo-source-ip ip-address

By default, the source IP address of BFD echo packets is not configured.

The source IP address cannot be on the same network segment as any local interface's IP address.

For more information about this command, see Network Management and Monitoring Command Reference.

3.     Enable BFD echo packet mode for static route FRR.

ip route-static primary-path-detect bfd echo

By default, BFD echo packet mode for static route FRR is disabled.

Display and maintenance commands for static routing

Execute display commands in any view.

 

Task	Command
Display static route information.	display ip routing-table protocol static [ inactive | verbose ]
Display static route next hop information.	display route-static nib [ nib-id ] [ verbose ]
Display static routing table information.	display route-static routing-table [ vpn-instance vpn-instance-name ] [ ip-address { mask-length | mask } ]

 

For more information about the display ip routing-table protocol static [ inactive | verbose ] command, see basic IP routing in Layer 3—IP Routing Command Reference.

Configuring a default route

A default route is used to forward packets that do not match any specific routing entry in the routing table. Without a default route, packets that do not match any routing entries are discarded and an ICMP destination-unreachable packet is sent to the source.

A default route can be configured in either of the following ways:

·     The network administrator can configure a default route with both destination and mask being 0.0.0.0. For more information, see "Configuring static routing."

·     Some dynamic routing protocols (such as OSPF and RIP) can generate a default route. For example, an upstream router running OSPF can generate a default route and advertise it to other routers. These routers install the default route with the next hop being the upstream router. For more information, see the respective chapters on these routing protocols in this configuration guide.