Contents

Configuring port mirroring· 1

About port mirroring· 1

Terminology· 1

Local port mirroring· 2

Restrictions: Hardware compatibility with port mirroring· 2

Configuring local port mirroring· 3

Restrictions and guidelines for local port mirroring configuration· 3

Local port mirroring tasks at a glance· 3

Creating a local mirroring group· 3

Configuring mirroring sources· 4

Configuring the monitor port 4

Display and maintenance commands for port mirroring· 5

Port mirroring configuration examples· 5

Example: Configuring local port mirroring· 5

 

Configuring port mirroring

About port mirroring

Port mirroring copies the packets passing through a port to a port that connects to a data monitoring device for packet analysis.

Terminology

The following terms are used in port mirroring configuration.

Mirroring source

The mirroring sources can be one or more monitored ports (called source ports).

Packets passing through mirroring sources are copied to a port connecting to a data monitoring device for packet analysis. The copies are called mirrored packets.

Source device

The device where the mirroring sources reside is called a source device.

Mirroring destination

The mirroring destination connects to a data monitoring device and is the destination port (also known as the monitor port) of mirrored packets. Mirrored packets are sent out of the monitor port to the data monitoring device.

A monitor port might receive multiple copies of a packet when it monitors multiple mirroring sources. For example, two copies of a packet are received on Port A when the following conditions exist:

·     Port A is monitoring bidirectional traffic of Port B and Port C on the same device.

·     The packet travels from Port B to Port C.

Destination device

The device where the monitor port resides is called the destination device.

Mirroring direction

The mirroring direction specifies the direction of the traffic that is copied on a mirroring source.

·     Inbound—Copies packets received.

·     Outbound—Copies packets sent.

·     Bidirectional—Copies packets received and sent.

Mirroring group

Port mirroring is implemented through local mirroring groups. The mirroring sources and destination reside on the same device, which is directly connected to a data monitoring device. Packets received on the mirroring sources are sent through the mirroring destination to the data monitoring device.

Local port mirroring

Figure 1 Local port mirroring implementation

‌

As shown in Figure 1, the source port (Port A) and the monitor port (Port B) reside on the same device. Packets received on Port A are copied to Port B. Port B then forwards the packets to the data monitoring device for analysis.

Restrictions: Hardware compatibility with port mirroring

Hardware series	Models	Product code	Port mirroring compatibility
WX1800H series	WX1804H	EWP-WX1804H-PWR-CN	Yes
WX2500H series	WX2508H-PWR-LTE WX2510H WX2510H-F WX2540H WX2540H-F WX2560H	EWP-WX2508H-PWR-LTE EWP-WX2510H-PWR EWP-WX2510H-F-PWR EWP-WX2540H EWP-WX2540H-F EWP-WX2560H	Yes
WX3000H series	WX3010H WX3010H-X WX3010H-L WX3024H WX3024H-L WX3024H-F	EWP-WX3010H EWP-WX3010H-X-PWR EWP-WX3010H-L-PWR EWP-WX3024H EWP-WX3024H-L-PWR EWP-WX3024H-F	Yes
WX3500H series	WX3508H WX3510H WX3520H WX3520H-F WX3540H	EWP-WX3508H EWP-WX3510H EWP-WX3520H EWP-WX3520H-F EWP-WX3540H	Yes
WX5500E series	WX5510E WX5540E	EWP-WX5510E EWP-WX5540E	Yes
WX5500H series	WX5540H WX5560H WX5580H	EWP-WX5540H EWP-WX5560H EWP-WX5580H	Yes
Access controller modules	LSUM1WCME0 EWPXM1WCME0 LSQM1WCMX20 LSUM1WCMX20RT LSQM1WCMX40 LSUM1WCMX40RT EWPXM2WCMD0F EWPXM1MAC0F	LSUM1WCME0 EWPXM1WCME0 LSQM1WCMX20 LSUM1WCMX20RT LSQM1WCMX40 LSUM1WCMX40RT EWPXM2WCMD0F EWPXM1MAC0F	No

‌

Hardware series	Models	Product code	Port mirroring compatibility
WX1800H series	WX1804H WX1810H WX1820H WX1840H	EWP-WX1804H-PWR EWP-WX1810H-PWR EWP-WX1820H EWP-WX1840H-GL	Yes
WX3800H series	WX3820H WX3840H	EWP-WX3820H-GL EWP-WX3840H-GL	Yes
WX5800H series	WX5860H	EWP-WX5860H-GL	Yes

‌

Configuring local port mirroring

Restrictions and guidelines for local port mirroring configuration

A local mirroring group takes effect only after it is configured with the monitor port and mirroring sources.

Local port mirroring tasks at a glance

To configure local port mirroring, perform the following tasks:

1.     Creating a local mirroring group

2.     Configuring mirroring sources

3.     Configuring the monitor port

Creating a local mirroring group

1.     Enter system view.

system-view

2.     Create a local mirroring group.

mirroring-group group-id local

Configuring mirroring sources

Restrictions and guidelines for mirroring source configuration

When you configure source ports for a local mirroring group, follow these restrictions and guidelines:

·     A mirroring group can contain multiple source ports.

·     A port can act as a source port for only one mirroring group.

·     A source port cannot be configured as a monitor port.

Configuring source ports

·     Configure source ports in system view:

a.     Enter system view.

system-view

b.     Configure source ports for a local mirroring group.

mirroring-group group-id mirroring-port interface-list { both | inbound | outbound }

By default, no source port is configured for a local mirroring group.

·     Configure source ports in interface view:

a.     Enter system view.

system-view

b.     Enter interface view.

interface interface-type interface-number

c.     Configure the port as a source port for a local mirroring group.

mirroring-group group-id mirroring-port { both | inbound | outbound }

By default, a port does not act as a source port for any local mirroring groups.

Configuring the monitor port

Restrictions and guidelines

Do not enable the spanning tree feature on the monitor port.

Only one monitor port can be specified for a local mirroring group.

Use a monitor port only for port mirroring, so the data monitoring device receives only the mirrored traffic.

Procedure

·     Configure the monitor port in system view:

a.     Enter system view.

system-view

b.     Configure the monitor port for a local mirroring group.

mirroring-group group-id monitor-port interface-type interface-number

By default, no monitor port is configured for a local mirroring group.

·     Configure the monitor port in interface view:

a.     Enter system view.

system-view

b.     Enter interface view.

interface interface-type interface-number

c.     Configure the port as the monitor port for a mirroring group.

mirroring-group group-id monitor-port

By default, a port does not act as the monitor port for any local mirroring groups.

Display and maintenance commands for port mirroring

Execute display commands in any view.

 

Task	Command
Display mirroring group information.	display mirroring-group { group-id | all | local }

‌

Port mirroring configuration examples

Example: Configuring local port mirroring

Network configuration

As shown in Figure 2, configure local port mirroring to enable the server to monitor the bidirectional traffic of the marketing and technical departments.

Figure 2 Network diagram

‌

Procedure

# Create local mirroring group 1.

<AC> system-view

[AC] mirroring-group 1 local

# Configure the source port and the monitor port in local mirroring group 1.

[AC] mirroring-group 1 mirroring-port gigabitethernet 1/0/1 both

[AC] mirroring-group 1 monitor-port gigabitethernet 1/0/2

Verifying the configuration

# Verify the mirroring group configuration.

[AC] display mirroring-group 1

Mirroring group 1:

    Type: Local

    Status: Active

    Mirroring port:

        GigabitEthernet1/0/1  Both

    Monitor port: GigabitEthernet1/0/2