As shown in Figure 1, when IGMP snooping is not enabled, the Layer 2 device floods multicast packets to all hosts. When IGMP snooping is enabled, the Layer 2 device forwards multicast packets of known multicast groups to only the receivers.

Figure 1 Multicast packet transmission without and with IGMP snooping

IGMP snooping ports

As shown in Figure 2, IGMP snooping runs on Device B and Device C, and Host A and Host C are receivers in a multicast group. IGMP snooping ports are divided into member ports and router ports.

Figure 2 IGMP snooping ports

Router ports

On an IGMP snooping Layer 2 device, the ports toward Layer 3 multicast devices are called router ports. In Figure 2, Port A1 of Device A and Port B1 of Device B are router ports.

Router ports contain the following types:

· Dynamic router port—When a port receives an IGMP general query whose source address is not 0.0.0.0 or receives a PIM hello message, the port is added into the dynamic router port list. At the same time, an aging timer is started for the port. If the port receives either of the messages before the timer expires, the timer is reset. If the port does not receive either of the messages when the timer expires, the port is removed from the dynamic router port list.

· Static router port—When a port is statically configured as a router port, it is added into the static router port list. The static router port does not age out, and it can be deleted only manually.

Do not confuse the "router port" in IGMP snooping with the "routed interface" commonly known as the "Layer 3 interface." The router port in IGMP snooping is a Layer 2 interface.

Member ports

On an IGMP snooping Layer 2 device, the ports toward receiver hosts are called member ports. In Figure 2, Port A2 and Port A3 of Device A and Port B2 of Device B are member ports.

Member ports contain the following types:

· Dynamic member port—When a port receives an IGMP report, it is added to the associated dynamic IGMP snooping forwarding entry as an outgoing interface. At the same time, an aging timer is started for the port. If the port receives an IGMP report before the timer expires, the timer is reset. If the port does not receive an IGMP report when the timer expires, the port is removed from the associated dynamic forwarding entry.

· Static member port—When a port is statically configured as a member port, it is added to the associated static IGMP snooping forwarding entry as an outgoing interface. The static member port does not age out, and it can be deleted only manually.

Unless otherwise specified, router ports and member ports in this document include both static and dynamic router ports and member ports.

How IGMP snooping works

The ports in this section are dynamic ports. For information about how to configure and remove static ports, see "Configuring a static member port" and "Configuring a static router port."

IGMP messages types include general query, IGMP report, and leave message. An IGMP snooping-enabled Layer 2 device performs differently depending on the message types.

General query

The IGMP querier periodically sends IGMP general queries to all hosts and devices on the local subnet to check for the existence of multicast group members.

After receiving an IGMP general query, the Layer 2 device forwards the query to all ports in the VLAN except the receiving port. The Layer 2 device also performs one of the following actions:

· If the receiving port is a dynamic router port in the dynamic router port list, the Layer 2 device restarts the aging timer for the port.

· If the receiving port does not exist in the dynamic router port list, the Layer 2 device adds the port to the dynamic router port list. It also starts an aging timer for the port.

IGMP report

A host sends an IGMP report to the IGMP querier for the following purposes:

· Responds to queries if the host is a multicast group member.

· Applies for a multicast group membership.

After receiving an IGMP report from a host, the Layer 2 device forwards the report through all the router ports in the VLAN. It also resolves the address of the reported multicast group, and looks up the forwarding table for a matching entry as follows:

· If no match is found, the Layer 2 device creates a forwarding entry with the receiving port as an outgoing interface. It also marks the receiving port as a dynamic member port and starts an aging timer for the port.

· If a match is found but the matching forwarding entry does not contain the receiving port, the Layer 2 device adds the receiving port to the outgoing interface list. It also marks the receiving port as a dynamic member port and starts an aging timer for the port.

· If a match is found and the matching forwarding entry contains the receiving port, the Layer 2 device restarts the aging timer for the port.

NOTE:

A Layer 2 device does not forward an IGMP report through a non-router port because of the host IGMP report suppression mechanism. If a non-router port has member host attached, the member hosts suppress their IGMP reports upon receiving IGMP reports forwarded by the non-router port. The Layer 2 device cannot know the existence of the member hosts attached to the non-router port. For more information about the IGMP report suppression mechanism, see "Configuring IGMP."

Leave message

An IGMPv1 receiver host does not send any leave messages when it leaves a multicast group. The Layer 2 device cannot immediately update the status of the port that connects to the receiver host. The Layer 2 device does not remove the port from the outgoing interface list in the associated forwarding entry until the aging time for the group expires.

An IGMPv2 or IGMPv3 host sends an IGMP leave message when it leaves a multicast group.

When the Layer 2 device receives an IGMP leave message on a dynamic member port, the Layer 2 device first examines whether a forwarding entry matches the group address in the message.

· If no match is found, the Layer 2 device discards the IGMP leave message.

· If a match is found but the receiving port is not an outgoing interface in the forwarding entry, the Layer 2 device discards the IGMP leave message.

· If a match is found and the receiving port is not the only outgoing interface in the forwarding entry, the Layer 2 device performs the following actions:

¡ Discards the IGMP leave message.

¡ Sends an IGMP group-specific query to identify whether the group has active receivers attached to the receiving port.

¡ Sets the aging timer for the receiving port to twice the IGMP last member query interval.

· If a match is found and the receiving port is the only outgoing interface in the forwarding entry, the Layer 2 device performs the following actions:

¡ Forwards the IGMP leave message to all router ports in the VLAN.

¡ Sends an IGMP group-specific query to identify whether the group has active receivers attached to the receiving port.

¡ Sets the aging timer for the receiving port to twice the IGMP last member query interval.

After receiving the IGMP leave message on a port, the IGMP querier resolves the multicast group address in the message. Then, it sends an IGMP group-specific query to the multicast group through the receiving port.

After receiving the IGMP group-specific query, the Layer 2 device forwards the query through all router ports and member ports of the group in the VLAN. Then, it waits for the responding IGMP report from the directly connected hosts. For the dynamic member port that received the leave message, the Layer 2 device also performs one of the following actions:

· If the port receives an IGMP report before the aging timer expires, the Layer 2 device resets the aging timer.

· If the port does not receive an IGMP report when the aging timer expires, the Layer 2 device removes the port from the forwarding entry for the multicast group.

IGMP snooping proxying

As shown in Figure 3, to reduce the number of IGMP report and leave messages received by the upstream device, you can enable IGMP snooping proxying on the edge device. With IGMP snooping proxying enabled, the edge device acts as a host for the upstream IGMP snooping querier to send IGMP report and leave messages to Device A. The host IGMP report suppression mechanism on the edge device does not take effect. For more information about the IGMP report suppression mechanism, see "Configuring IGMP."

Figure 3 IGMP snooping proxying

The IGMP snooping proxy device processes different IGMP messages as follows:

· General query.

After receiving an IGMP general query, the device forwards the query to all ports in the VLAN except the receiving port. The device also generates an IGMP report based on the local membership information and sends the report to all router ports.

· Group-specific query or group-and-source-specific query.

After receiving an IGMP group-specific query or group-and-source-specific query, the device forwards the query to all ports in the VLAN except the receiving port. If the forwarding entry has a member port, the device sends a report to all router ports in the VLAN.

· Report.

After receiving an IGMP report from a host, the device looks up the forwarding table for a matching entry as follows:

¡ If a match is found and the matching forwarding entry contains the receiving port, the device resets the aging timer for the port.

¡ If a match is found but the matching forwarding entry does not contain the receiving port, the device adds the receiving port to the outgoing interface list. It also marks the receiving port as a dynamic member port and starts an aging timer for the port.

¡ If no match is found, the device creates a forwarding entry with the receiving port as an outgoing interface. It also marks the receiving port as a dynamic member port and starts an aging timer for the port. Then it sends the report to all router ports.

· Leave message.

After receiving the IGMP leave message on a port, the device sends an IGMP group-specific query through the receiving port. The device sends the IGMP leave message to all router ports only when the last member port is removed from the forwarding entry.

Protocols and standards

RFC 4541, Considerations for Internet Group Management Protocol (IGMP) and Multicast Listener Discovery (MLD) Snooping Switches

Restrictions and guidelines: IGMP snooping configuration

The IGMP snooping configurations made on Layer 2 aggregate interfaces do not interfere with the configurations made on member ports. In addition, the configurations made on Layer 2 aggregate interfaces do not take part in aggregation calculations. The configuration made on a member port of the aggregate group takes effect after the port leaves the aggregate group.

To configure IGMP snooping features for VLANs, you must enable IGMP snooping for the specific VLANs even though IGMP snooping is enabled globally.

Some features can be configured for a VLAN in VLAN view or for multiple VLANs in IGMP-snooping view. The configuration made in VLAN view and the configuration made in IGMP-snooping view have the same priority, and the most recent configuration takes effect.

Some features can be configured for a VLAN in VLAN view or globally for all VLANs in IGMP-snooping view. The VLAN-specific configuration takes priority over the global configuration.

Some features can be configured for an interface in interface view or for all interfaces of the specified VLANs in IGMP-snooping view. The interface-specific configuration takes priority over the configuration made in IGMP-snooping view.

VLAN-based IGMP snooping tasks at a glance

To configure IGMP snooping for VLANs, perform the following tasks:

1. Enabling IGMP snooping

2. (Optional.) Configuring basic IGMP snooping features

¡ Specifying an IGMP snooping version

¡ Setting the maximum number of IGMP snooping forwarding entries

¡ Configuring static multicast MAC address entries

¡ Setting the IGMP last member query interval

3. (Optional.) Configuring IGMP snooping port features

¡ Setting aging timers for dynamic ports

¡ Configuring a static member port

¡ Configuring a static router port

¡ Configuring a port as a simulated member host

¡ Enabling fast-leave processing

4. (Optional.) Configuring the IGMP snooping querier

¡ Enabling the IGMP snooping querier

¡ Configuring parameters for IGMP general queries and responses

5. (Optional.) Enabling IGMP snooping proxying

6. (Optional.) Configuring parameters for IGMP messages

¡ Configuring source IP addresses for IGMP messages

¡ Setting the 802.1p priority for IGMP messages

7. (Optional.) Configuring IGMP snooping policies

¡ Configuring a multicast group policy

¡ Enabling multicast source port filtering

¡ Enabling dropping unknown multicast data

¡ Enabling IGMP report suppression

¡ Setting the maximum number of multicast groups on a port

¡ Enabling host tracking

Enabling IGMP snooping

Enabling IGMP snooping for multiple VLANs

1. Enter system view.

system-view

2. Enable IGMP snooping globally and enter IGMP-snooping view.

igmp-snooping

By default, IGMP snooping is globally disabled.

3. Enable IGMP snooping for the specified VLANs.

enable vlan vlan-list

By default, IGMP snooping is disabled for a VLAN.

IGMP snooping configuration in a VLAN takes effect only on the member ports in the VLAN.

Enabling IGMP snooping for a VLAN

1. Enter system view.

system-view

2. Enable IGMP snooping globally and enter IGMP-snooping view.

igmp-snooping

By default, IGMP snooping is globally disabled.

3. Return to system view.

quit

4. Enter VLAN view.

vlan vlan-id

5. Enable IGMP snooping for the VLAN.

igmp-snooping enable

By default, IGMP snooping is disabled for a VLAN.

IGMP snooping configuration in a VLAN takes effect only on the member ports in the VLAN.

Configuring basic IGMP snooping features

Specifying an IGMP snooping version

About this task

Different IGMP snooping versions process different versions of IGMP messages.

· IGMPv2 snooping processes IGMPv1 and IGMPv2 messages, but it floods IGMPv3 messages in the VLAN instead of processing them.

· IGMPv3 snooping processes IGMPv1, IGMPv2, and IGMPv3 messages.

Restrictions and guidelines

If you change the IGMP snooping version from 2 to 3, the device performs the following actions:

· Clears all IGMP snooping forwarding entries that are dynamically created.

· Keeps static IGMPv3 snooping forwarding entries (*, G).

· Clears static IGMPv3 snooping forwarding entries (S, G), which will be restored when the IGMP snooping version is switched back to 3.

For more information about static IGMP snooping forwarding entries, see "Configuring a static member port."

Specifying an IGMP snooping version for multiple VLANs

1. Enter system view.

system-view

2. Enter IGMP-snooping view.

igmp-snooping

3. Specify an IGMP snooping version for multiple VLANs.

version version-number vlan vlan-list

By default, the IGMP snooping version for a VLAN is 2.

Specifying an IGMP snooping version for a VLAN

1. Enter system view.

system-view

2. Enter VLAN view.

vlan vlan-id

3. Specify an IGMP snooping version for the VLAN.

igmp-snooping version version-number

By default, the IGMP snooping version for a VLAN is 2.

Setting the maximum number of IGMP snooping forwarding entries

About this task

You can modify the maximum number of IGMP snooping forwarding entries, including dynamic entries and static entries. When the number of forwarding entries on the device reaches the upper limit, the device does not automatically remove any existing entries. To allow new entries to be created, remove some entries manually.

Procedure

1. Enter system view.

system-view

2. Enter IGMP-snooping view.

igmp-snooping

3. Set the maximum number of IGMP snooping forwarding entries.

entry-limit limit

By default, the maximum number of IGMP snooping forwarding entries is 4294967295.

Configuring static multicast MAC address entries

About this task

In Layer 2 multicast, multicast MAC address entries can be dynamically created through Layer 2 multicast protocols (such as IGMP snooping). You can also manually configure static multicast MAC address entries by binding multicast MAC addresses and ports to control the destination ports of the multicast data.

Restrictions and guidelines

You must specify an unused multicast MAC address when configuring a static multicast MAC address entry. A multicast MAC address is the MAC address in which the least significant bit of the most significant octet is 1.

Configuring a static multicast MAC address entry in system view

1. Enter system view.

system-view

2. Configure a static multicast MAC address entry.

mac-address multicast mac-address interface interface-list vlan vlan-id

Configuring a static multicast MAC address entry in interface view

1. Enter system view.

system-view

2. Enter Layer 2 interface view.

¡ Enter Layer 2 Ethernet interface view.

interface interface-type interface-number

¡ Enter Layer 2 aggregate interface view.

interface bridge-aggregation interface-number

3. Configure a static multicast MAC address entry.

mac-address multicast mac-address vlan vlan-id

Setting the IGMP last member query interval

About this task

A receiver host starts a report delay timer for a multicast group when it receives an IGMP group-specific query for the group. This timer is set to a random value in the range of 0 to the maximum response time advertised in the query. When the timer value decreases to 0, the host sends an IGMP report to the group.

The IGMP last member query interval defines the maximum response time advertised in IGMP group-specific queries. Set an appropriate value for the IGMP last member query interval to speed up hosts' responses to IGMP group-specific queries and avoid IGMP report traffic bursts.

Setting the IGMP last member query interval globally

1. Enter system view.

system-view

2. Enter IGMP-snooping view.

igmp-snooping

3. Set the IGMP last member query interval globally.

last-member-query-interval interval

By default, the global IGMP last member query interval is 1 second.

Setting the IGMP last member query interval for a VLAN

1. Enter system view.

system-view

2. Enter VLAN view.

vlan vlan-id

3. Set the IGMP last member query interval for the VLAN.

igmp-snooping last-member-query-interval interval

By default, the IGMP last member query interval is 1 second for a VLAN.

Configuring IGMP snooping port features

Setting aging timers for dynamic ports

About this task

A dynamic router port is removed from the dynamic router port list if it does not receive an IGMP general query or PIM hello message when its aging timer expires.

A dynamic member port is removed from the dynamic member port if it does not receive an IGMP report when its aging timer expires.

Restrictions and guidelines

Set an appropriate value for the aging timers of dynamic ports. For example, if the memberships of multicast groups frequently change, set a relatively small value for the aging timer of the dynamic member ports. If the memberships of multicast groups rarely change, set a relatively large value.

If a dynamic router port receives a PIMv2 hello message, the aging timer for the port is specified by the hello message. In this case, the router-aging-time or igmp-snooping router-aging-time command does not take effect on the port.

IGMP group-specific queries originated by the Layer 2 device trigger the adjustment of aging timers for dynamic member ports. If a dynamic member port receives such a query, its aging timer is set to twice the IGMP last member query interval. For more information about setting the IGMP last member query interval on the Layer 2 device, see "Setting the IGMP last member query interval."

Setting the aging timers for dynamic ports globally

1. Enter system view.

system-view

2. Enter IGMP-snooping view.

igmp-snooping

3. Set the aging timer for dynamic router ports globally.

router-aging-time seconds

By default, the aging timer for dynamic router ports is 260 seconds.

4. Set the global aging timer for dynamic member ports globally.

host-aging-time seconds

By default, the aging timer for dynamic member ports is 260 seconds.

Setting the aging timers for dynamic ports in a VLAN

1. Enter system view.

system-view

2. Enter VLAN view.

vlan vlan-id

3. Set the aging timer for dynamic router ports in the VLAN.

igmp-snooping router-aging-time seconds

By default, the aging timer for dynamic router ports is 260 seconds.

4. Set the aging timer for dynamic member ports in the VLAN.

igmp-snooping host-aging-time seconds

By default, the aging timer for dynamic member ports is 260 seconds.

Configuring a static member port

About this task

You can configure a port as a static member port for a multicast group so that hosts attached to the port can always receive multicast for the group. The static member port does not respond to IGMP queries. When you complete or cancel this configuration on a port, the port does not send an unsolicited IGMP report or leave message.

Procedure

1. Enter system view.

system-view

2. Enter Layer 2 interface view.

¡ Enter Layer 2 Ethernet interface view.

interface interface-type interface-number

¡ Enter Layer 2 aggregate interface view.

interface bridge-aggregation interface-number

3. Configure the port as a static member port.

igmp-snooping static-group group-address [ source-ip source-address ] vlan vlan-id

By default, a port is not a static member port.

Configuring a static router port

About this task

You can configure a port as a static router port for a multicast group so that all multicast data for the group received on the port will be forwarded.

Procedure

1. Enter system view.

system-view

2. Enter Layer 2 interface view.

¡ Enter Layer 2 Ethernet interface view.

interface interface-type interface-number

¡ Enter Layer 2 aggregate interface view.

interface bridge-aggregation interface-number

3. Configure the port as a static router port.

igmp-snooping static-router-port vlan vlan-id

By default, a port is not a static router port.

Configuring a port as a simulated member host

About this task

When a port is configured as a simulated member host, it is equivalent to an independent host in the following ways:

· It sends an unsolicited IGMP report when you complete the configuration.

· It responds to IGMP general queries with IGMP reports.

· It sends an IGMP leave message when you cancel the configuration.

The version of IGMP running on the simulated member host is the same as the version of IGMP snooping running on the port. The port ages out in the same way as a dynamic member port.

Procedure

1. Enter system view.

system-view

2. Enter Layer 2 interface view.

¡ Enter Layer 2 Ethernet interface view.

interface interface-type interface-number

¡ Enter Layer 2 aggregate interface view.

interface bridge-aggregation interface-number

3. Configure the port as a simulated member host.

igmp-snooping host-join group-address [ source-ip source-address ] vlan vlan-id

By default, the port is not a simulated member host.

Enabling fast-leave processing

About this task

This feature enables the Layer 2 device to immediately remove a port from the forwarding entry for a multicast group when the port receives a leave massage. The Layer 2 device no longer sends or forwards IGMP group-specific queries for the group to the port.

Restrictions and guidelines

Do not enable fast-leave processing on a port that has multiple receiver hosts in a VLAN. If you do so, the remaining receivers cannot receive multicast data for a group after a receiver leaves the group.

Enabling fast-leave processing globally

1. Enter system view.

system-view

2. Enter IGMP-snooping view.

igmp-snooping

3. Enable fast-leave processing globally.

fast-leave [ vlan vlan-list ]

By default, fast-leave processing is disabled globally.

Enabling fast-leave processing on a port

1. Enter system view.

system-view

2. Enter Layer 2 interface view.

¡ Enter Layer 2 Ethernet interface view.

interface interface-type interface-number

¡ Enter Layer 2 aggregate interface view.

interface bridge-aggregation interface-number

3. Enable fast-leave processing on the port.

igmp-snooping fast-leave [ vlan vlan-list ]

By default, fast-leave processing is disabled on a port.

Configuring the IGMP snooping querier

Enabling the IGMP snooping querier

About this task

This feature enables the Layer 2 device to periodically send IGMP general queries to establish and maintain multicast forwarding entries at the data link Layer. You can configure an IGMP snooping querier on a network without Layer 3 multicast devices.

Restrictions and guidelines

Do not enable the IGMP snooping querier on a multicast network that runs IGMP. An IGMP snooping querier does not take part in IGMP querier elections. However, it might affect IGMP querier elections if it sends IGMP general queries with a low source IP address.

Enabling the IGMP snooping querier for a VLAN

1. Enter system view.

system-view

2. Enter VLAN view.

vlan vlan-id

3. Enable the IGMP snooping querier for the VLAN.

igmp-snooping querier

By default, the IGMP snooping querier is disabled for a VLAN.

Configuring parameters for IGMP general queries and responses

About this task

You can modify the IGMP general query interval for a VLAN based on the actual condition of the network.

A receiver host starts a report delay timer for each multicast group that it has joined when it receives an IGMP general query. This timer is set to a random value in the range of 0 to the maximum response time advertised in the query. When the timer value decreases to 0, the host sends an IGMP report to the corresponding multicast group.

Set an appropriate value for the maximum response time for IGMP general queries to speed up hosts' responses to IGMP general queries and avoid IGMP report traffic bursts.

Restrictions and guidelines

To avoid mistakenly deleting multicast group members, make sure the IGMP general query interval is greater than the maximum response time for IGMP general queries.

Configuring parameters for IGMP general queries and responses globally

1. Enter system view.

system-view

2. Enter IGMP-snooping view.

igmp-snooping

3. Set the maximum response time for IGMP general queries.

max-response-time seconds

By default, the maximum response time for IGMP general queries is 10 seconds.

Configuring parameters for IGMP general queries and responses in a VLAN

1. Enter system view.

system-view

2. Enter VLAN view.

vlan vlan-id

3. Set the IGMP general query interval in the VLAN.

igmp-snooping query-interval interval

By default, the IGMP general query interval is 125 seconds for a VLAN.

4. Set the maximum response time for IGMP general queries in the VLAN.

igmp-snooping max-response-time seconds

By default, the maximum response time for IGMP general queries is 10 seconds for a VLAN.

Enabling IGMP snooping proxying

5. Enter system view.

system-view

6. Enter VLAN view.

vlan vlan-id

7. Enable IGMP snooping proxying for the VLAN.

igmp-snooping proxy enable

By default, IGMP snooping proxying is disabled for a VLAN.

Configuring parameters for IGMP messages

Configuring source IP addresses for IGMP messages

About this task

The IGMP snooping querier might send IGMP general queries with the source IP address 0.0.0.0. The port that receives such queries will not be maintained as a dynamic router port. This might prevent the associated dynamic IGMP snooping forwarding entry from being correctly created at the data link layer and eventually cause multicast traffic forwarding failures. To avoid this problem, you can configure a non-all-zero IP address as the source IP address of the IGMP queries on the IGMP snooping querier. This configuration might affect the IGMP querier election within the subnet.

You can also change the source IP address of IGMP reports or leave messages sent by a simulated member host or an IGMP snooping proxy.

Configuring the source IP addresses for IGMP messages in a VLAN

1. Enter system view.

system-view

2. Enter VLAN view.

vlan vlan-id

3. Configure the source IP address for IGMP general queries.

igmp-snooping general-query source-ip ip-address

By default, the source IP address of IGMP general queries is the IP address of the current VLAN interface. If the current VLAN interface does not have an IP address, the source IP address is 0.0.0.0.

4. Configure the source IP address for IGMP group-specific queries.

igmp-snooping special-query source-ip ip-address

By default, the source IP address of IGMP group-specific queries is one of the following:

¡ The source address of IGMP group-specific queries if the IGMP snooping querier of the VLAN has received IGMP general queries.

¡ The IP address of the current VLAN interface if the IGMP snooping querier does not receive an IGMP general query.

¡ 0.0.0.0 if the IGMP snooping querier does not receive an IGMP general query and the current VLAN interface does not have an IP address.

5. Configure the source IP address for IGMP reports.

igmp-snooping report source-ip ip-address

By default, the source IP address of IGMP reports is the IP address of the current VLAN interface. If the current VLAN interface does not have an IP address, the source IP address is 0.0.0.0.

6. Configure the source IP address for IGMP leave messages.

igmp-snooping leave source-ip ip-address

By default, the source IP address of IGMP leave messages is the IP address of the current VLAN interface. If the current VLAN interface does not have an IP address, the source IP address is 0.0.0.0.

Setting the 802.1p priority for IGMP messages

About this task

When congestion occurs on outgoing ports of the Layer 2 device, it forwards IGMP messages in their 802.1p priority order, from highest to lowest. You can assign a higher 802.1p priority to IGMP messages that are created or forwarded by the device.

Setting the 802.1p priority for IGMP messages globally

1. Enter system view.

system-view

2. Enter IGMP-snooping view.

igmp-snooping

3. Set the 802.1p priority for IGMP messages.

dot1p-priority priority

By default, the 802.1p priority is 6 for IGMP packets.

Setting the 802.1p priority for IGMP messages in a VLAN

1. Enter system view.

system-view

2. Enter VLAN view.

vlan vlan-id

3. Set the 802.1p priority for IGMP messages in the VLAN.

igmp-snooping dot1p-priority priority

By default, the 802.1p priority is 6 for IGMP packets in a VLAN.

Configuring IGMP snooping policies

Configuring a multicast group policy

About this task

This feature enables the Layer 2 device to filter IGMP reports by using an ACL that specifies the multicast groups and the optional sources. It is used to control the multicast groups that hosts can join. This configuration takes effect only on the multicast groups that ports join dynamically.

In a multicast application, a host sends an unsolicited IGMP report when a user requests a multicast program. The Layer 2 device uses the multicast group policy to filter the IGMP report. The host can join the multicast group only if the IGMP report is permitted by the multicast group policy.

Configuring a multicast group policy globally

1. Enter system view.

system-view

2. Enter IGMP-snooping view.

igmp-snooping

3. Configure a multicast group policy globally.

group-policy ipv4-acl-number [ vlan vlan-list ]

By default, no multicast group policies are configured, and hosts can join any multicast groups.

Configuring a multicast group policy on a port

1. Enter system view.

system-view

2. Enter Layer 2 interface view.

¡ Enter Layer 2 Ethernet interface view.

interface interface-type interface-number

¡ Enter Layer 2 aggregate interface view.

interface bridge-aggregation interface-number

3. Configure a multicast group policy on the port.

igmp-snooping group-policy ipv4-acl-number [ vlan vlan-list ]

By default, no multicast group policies are configured on a port, and hosts attached to the port can join any multicast groups.

Enabling multicast source port filtering

About this task

This feature enables the Layer 2 device to discard all multicast data packets and to accept multicast protocol packets. You can enable this feature on ports that connect only to multicast receivers.

Restrictions and guidelines

When IPv4 multicast source port filtering is enabled, the device also enables IPv6 multicast source port filtering.

The configuration made for multiple interfaces in IGMP-snooping view has the same priority as the interface-specific configuration, and the most recent configuration takes effect.

Enabling multicast source port filtering in IGMP-snooping view

1. Enter system view.

system-view

2. Enter IGMP-snooping view.

igmp-snooping

3. Enable multicast source port filtering.

source-deny port interface-list

By default, multicast source port filtering is disabled.

Enabling multicast source port filtering in interface view

1. Enter system view.

system-view

2. Enter Layer 2 Ethernet interface view.

interface interface-type interface-number

3. Enable multicast source port filtering.

igmp-snooping source-deny

By default, multicast source port filtering is disabled.

Enabling dropping unknown multicast data

About this task

This feature enables the Layer 2 device to drop all unknown multicast data. Unknown multicast data refers to multicast data for which no forwarding entries exist in the IGMP snooping forwarding table.

If you do not enable this feature, the unknown multicast data is flooded in the VLAN to which the data belongs.

Restrictions and guidelines

When dropping unknown IPv4 multicast data is enabled, the device also drops unknown IPv6 multicast data.

When this feature is enabled for a VLAN, the device still forwards unknown multicast data out of router ports except the receiving router port in this VLAN.

Enabling dropping unknown multicast data for a VLAN

1. Enter system view.

system-view

2. Enter VLAN view.

vlan vlan-id

3. Enable dropping unknown multicast data for the VLAN.

igmp-snooping drop-unknown

By default, dropping unknown multicast data is disabled for a VLAN. Unknown multicast data is flooded in the VLAN.

Enabling IGMP report suppression

About this task

This feature enables the Layer 2 device to forward only the first IGMP report for a multicast group to its directly connected Layer 3 device. Other reports for the same group in the same query interval are discarded. Use this feature to reduce multicast traffic.

Procedure

1. Enter system view.

system-view

2. Enter IGMP-snooping view.

igmp-snooping

3. Enable IGMP report suppression.

report-aggregation

By default, IGMP report suppression is enabled.

Setting the maximum number of multicast groups on a port

About this task

You can set the maximum number of multicast groups on a port to regulate the port traffic. This feature takes effect only on the multicast groups that a port joins dynamically.

If the number of multicast groups on a port exceeds the limit, the system removes all the forwarding entries associated with the port. The receiver hosts attached to that port can join multicast groups again before the number of multicast groups on the port reaches the limit. When the number of multicast groups on the port reaches the limit, the port automatically drops IGMP reports for new groups.

Procedure

1. Enter system view.

system-view

2. Enter Layer 2 interface view.

¡ Enter Layer 2 Ethernet interface view.

interface interface-type interface-number

¡ Enter Layer 2 aggregate interface view.

interface bridge-aggregation interface-number

3. Set the maximum number of multicast groups on the port.

igmp-snooping group-limit limit [ vlan vlan-list ]

By default, no limit is placed on the maximum number of multicast groups on a port.

Enabling host tracking

About this task

This feature enables the Layer 2 device to record information about member hosts that are receiving multicast data. The information includes IP addresses of the hosts, length of time elapsed since the hosts joined multicast groups, and remaining timeout time for the hosts. This feature facilitates monitoring and managing member hosts.

Enabling host tracking globally

1. Enter system view.

system-view

2. Enter IGMP-snooping view.

igmp-snooping

3. Enable host tracking globally.

host-tracking

By default, host tracking is disabled globally.

Enabling host tracking for a VLAN

1. Enter system view.

system-view

2. Enter VLAN view.

vlan vlan-id

3. Enable host tracking for the VLAN.

igmp-snooping host-tracking

By default, host tracking is disabled for a VLAN.

Display and maintenance commands for IGMP snooping

Execute display commands in any view and reset commands in user view.

Task	Command
Display IGMP snooping status.	display igmp-snooping [ global \| vlan vlan-id ]
Display dynamic IGMP snooping group entries.	display igmp-snooping group [ group-address \| source-address ] * [ vlan vlan-id ] [ verbose ] [ slot slot-number ]
Display host tracking information.	display igmp-snooping host-tracking vlan vlan-id group group-address [ source source-address ] [ slot slot-number ]
Display dynamic router port information.	display igmp-snooping router-port [ verbose \| vlan vlan-id [ verbose ] ] [ slot slot-number ]
Display static IGMP snooping group entries.	display igmp-snooping static-group [ group-address \| source-address ] * [ vlan vlan-id ] [ verbose ] [ slot slot-number ]
Display static router port information.	display igmp-snooping static-router-port [ vlan vlan-id ] [ slot slot-number ]
Display statistics for the IGMP messages and PIMv2 hello messages learned by IGMP snooping.	display igmp-snooping statistics
Display Layer 2 multicast fast forwarding entries.	display l2-multicast fast-forwarding cache [ vlan vlan-id ] [ source-address \| group-address ] * [ slot slot-number ]
Display information about Layer 2 IP multicast groups.	display l2-multicast ip [ group group-address \| source source-address ] * [ vlan vlan-id ] [ slot slot-number ]
Display Layer 2 IP multicast group entries.	display l2-multicast ip forwarding [ group group-address \| source source-address ] * [ vlan vlan-id ] [ slot slot-number ]
Display information about Layer 2 MAC multicast groups.	display l2-multicast mac [ mac-address ] [ vlan vlan-id ] [ slot slot-number ]
Display Layer 2 MAC multicast group entries.	display l2-multicast mac forwarding [ mac-address ] [ vlan vlan-id ] [ slot slot-number ]
Display static multicast MAC address entries.	display mac-address [ mac-address [ vlan vlan-id ] \| [ multicast ] [ vlan vlan-id ] [ count ] ]
Clear Layer 2 multicast fast forwarding entries.	reset l2-multicast fast-forwarding cache [ vlan vlan-id ] { { source-address \| group-address } * \| all } [ slot slot-number ]
Clear dynamic IGMP snooping group entries.	reset igmp-snooping group { group-address [ source-address ] \| all } [ vlan vlan-id ]
Clear dynamic router port information.	reset igmp-snooping router-port { all \| vlan vlan-id }
Clear statistics for IGMP messages and PIMv2 hello messages learned through IGMP snooping.	reset igmp-snooping statistics

IGMP snooping configuration examples

Example: Configuring VLAN-based IGMP snooping group polices and simulated joining

Network configuration

As shown in Figure 4, Router A runs IGMPv2 and acts as the IGMP querier. Device A runs IGMPv2 snooping.

Configure a multicast group policy and simulated joining to meet the following requirements:

· Host A and Host B receive only the multicast data addressed to multicast group 224.1.1.1. Multicast data can be forwarded through HundredGigE 1/0/3 and HundredGigE 1/0/4 of Device A uninterruptedly, even though Host A and Host B fail to receive the multicast data.

· Device A will drop unknown multicast data instead of flooding it in VLAN 100 .

Figure 4 Network diagram

‌

Prerequisites

By default, interfaces on the device are disabled (in ADM or Administratively Down state). To have an interface operate, you must use the undo shutdown command to enable that interface.

Interfaces in this example refer to Layer 2 interfaces. By default, interfaces on the device operate at Layer 3 mode. To change the link mode of an interface, use the port link-mode command in interface view.

Assign an IP address and subnet mask to each interface.

Procedure

1. Configure Router A:

# Enable IP multicast routing.

<RouterA> system-view

[RouterA] multicast routing

[RouterA-mrib] quit

# Enable IGMP on HundredGigE 1/0/1.

[RouterA] interface hundredgige 1/0/1

[RouterA-HundredGigE1/0/1] igmp enable

[RouterA-HundredGigE1/0/1] quit

# Enable PIM-DM on HundredGigE 1/0/2.

[RouterA] interface hundredgige 1/0/2

[RouterA-HundredGigE1/0/2] pim dm

[RouterA-HundredGigE1/0/2] quit

2. Configure Device A:

# Enable IGMP snooping globally.

<DeviceA> system-view

[DeviceA] igmp-snooping

[DeviceA-igmp-snooping] quit

# Create VLAN 100, and assign HundredGigE 1/0/1 through HundredGigE 1/0/4 to the VLAN.

[DeviceA] vlan 100

[DeviceA-vlan100] port hundredgige 1/0/1 to hundredgige 1/0/4

# Enable IGMP snooping, and enable dropping unknown multicast data for VLAN 100.

[DeviceA-vlan100] igmp-snooping enable

[DeviceA-vlan100] igmp-snooping drop-unknown

[DeviceA-vlan100] quit

# Configure a multicast group policy so that hosts in VLAN 100 can join only multicast group 224.1.1.1.

[DeviceA] acl basic 2001

[DeviceA-acl-ipv4-basic-2001] rule permit source 224.1.1.1 0

[DeviceA-acl-ipv4-basic-2001] quit

[DeviceA] igmp-snooping

[DeviceA-igmp-snooping] group-policy 2001 vlan 100

[DeviceA-igmp-snooping] quit

# Configure HundredGigE 1/0/3 and HundredGigE 1/0/4 as simulated member hosts of multicast group 224.1.1.1.

[DeviceA] interface hundredgige 1/0/3

[DeviceA-HundredGigE1/0/3] igmp-snooping host-join 224.1.1.1 vlan 100

[DeviceA-HundredGigE1/0/3] quit

[DeviceA] interface hundredgige 1/0/4

[DeviceA-HundredGigE1/0/4] igmp-snooping host-join 224.1.1.1 vlan 100

[DeviceA-HundredGigE1/0/4] quit

Verifying the configuration

# Send IGMP reports from Host A and Host B to join multicast groups 224.1.1.1 and 224.2.2.2. (Details not shown.)

# Display dynamic IGMP snooping group entries for VLAN 100 on Device A.

[DeviceA] display igmp-snooping group vlan 100

Total 1 entries.

VLAN 100: Total 1 entries.

(0.0.0.0, 224.1.1.1)

Host slots (0 in total):

Host ports (2 in total):

HGE1/0/3 (00:03:23)

HGE1/0/4 (00:04:10)

The output shows the following information:

· Host A and Host B have joined multicast group 224.1.1.1 through the member ports HundredGigE 1/0/4 and HundredGigE 1/0/3 on Device A, respectively.

· Host A and Host B have failed to join multicast group 224.2.2.2.

Example: Configuring VLAN-based IGMP snooping static ports

Network configuration

As shown in Figure 5:

· Router A runs IGMPv2 and acts as the IGMP querier. Device A, Device B, and Device C run IGMPv2 snooping.

· Host A and host C are permanent receivers of multicast group 224.1.1.1.

Configure static ports to meet the following requirements:

· To enhance the reliability of multicast traffic transmission, configure HundredGigE 1/0/3 and HundredGigE 1/0/5 on Device C as static member ports for multicast group 224.1.1.1.

· Suppose the STP runs on the network. To avoid data loops, the forwarding path from Device A to Device C is blocked. Multicast data flows to the receivers attached to Device C only along the path of Device A—Device B—Device C. When this path is blocked, a minimum of one IGMP query-response cycle must be completed before multicast data flows to the receivers along the path of Device A—Device C. In this case, the multicast delivery is interrupted during the process. For more information about the STP, see Layer 2—LAN Switching Configuration Guide.

Configure HundredGigE 1/0/3 on Device A as a static router port. Then, multicast data can flow to the receivers nearly uninterruptedly along the path of Device A—Device C when the path of Device A—Device B—Device C is blocked.

Figure 5 Network diagram

‌

Prerequisites

By default, interfaces on the device are disabled (in ADM or Administratively Down state). To have an interface operate, you must use the undo shutdown command to enable that interface.

Assign an IP address and subnet mask to each interface.

Procedure

1. Configure Router A:

# Enable IP multicast routing.

<RouterA> system-view

[RouterA] multicast routing

[RouterA-mrib] quit

# Enable IGMP on HundredGigE 1/0/1.

[RouterA] interface hundredgige 1/0/1

[RouterA-HundredGigE1/0/1] igmp enable

[RouterA-HundredGigE1/0/1] quit

# Enable PIM-DM on HundredGigE 1/0/2.

[RouterA] interface hundredgige 1/0/2

[RouterA-HundredGigE1/0/2] pim dm

[RouterA-HundredGigE1/0/2] quit

2. Configure Device A:

# Enable IGMP snooping globally.

<DeviceA> system-view

[DeviceA] igmp-snooping

[DeviceA-igmp-snooping] quit

# Create VLAN 100, and assign HundredGigE 1/0/1 through HundredGigE 1/0/3 to the VLAN.

[DeviceA] vlan 100

[DeviceA-vlan100] port hundredgige 1/0/1 to hundredgige 1/0/3

# Enable IGMP snooping for VLAN 100.

[DeviceA-vlan100] igmp-snooping enable

[DeviceA-vlan100] quit

# Configure HundredGigE 1/0/3 as a static router port.

[DeviceA] interface hundredgige 1/0/3

[DeviceA-HundredGigE1/0/3] igmp-snooping static-router-port vlan 100

[DeviceA-HundredGigE1/0/3] quit

3. Configure Device B:

# Enable IGMP snooping globally.

<DeviceB> system-view

[DeviceB] igmp-snooping

[DeviceB-igmp-snooping] quit

# Create VLAN 100, and assign HundredGigE 1/0/1 and HundredGigE 1/0/2 to the VLAN.

[DeviceB] vlan 100

[DeviceB-vlan100] port hundredgige 1/0/1 hundredgige 1/0/2

# Enable IGMP snooping for VLAN 100.

[DeviceB-vlan100] igmp-snooping enable

[DeviceB-vlan100] quit

4. Configure Device C:

# Enable IGMP snooping globally.

<DeviceC> system-view

[DeviceC] igmp-snooping

[DeviceC-igmp-snooping] quit

# Create VLAN 100, and assign HundredGigE 1/0/1 through HundredGigE 1/0/5 to the VLAN.

[DeviceC] vlan 100

[DeviceC-vlan100] port hundredgige 1/0/1 to hundredgige 1/0/5

# Enable IGMP snooping for VLAN 100.

[DeviceC-vlan100] igmp-snooping enable

[DeviceC-vlan100] quit

# Configure HundredGigE 1/0/3 and HundredGigE 1/0/5 as static member ports for multicast group 224.1.1.1.

[DeviceC] interface hundredgige 1/0/3

[DeviceC-HundredGigE1/0/3] igmp-snooping static-group 224.1.1.1 vlan 100

[DeviceC-HundredGigE1/0/3] quit

[DeviceC] interface hundredgige 1/0/5

[DeviceC-HundredGigE1/0/5] igmp-snooping static-group 224.1.1.1 vlan 100

[DeviceC-HundredGigE1/0/5] quit

Verifying the configuration

# Display static router port information for VLAN 100 on Device A.

[DeviceA] display igmp-snooping static-router-port vlan 100

VLAN 100:

Router slots (0 in total):

Router ports (1 in total):

HGE1/0/3

The output shows that HundredGigE 1/0/3 on Device A has become a static router port.

# Display static IGMP snooping group entries for VLAN 100 on Device C.

[DeviceC] display igmp-snooping static-group vlan 100

Total 1 entries.

VLAN 100: Total 1 entries.

(0.0.0.0, 224.1.1.1)

Host slots (0 in total):

Host ports (2 in total):

HGE1/0/3

HGE1/0/5

The output shows that HundredGigE 1/0/3 and HundredGigE 1/0/5 on Device C have become static member ports of multicast group 224.1.1.1.

Example: Configuring the VLAN-based IGMP snooping querier

Network configuration

As shown in Figure 6:

· The network is a Layer 2-only network.

· Source 1 and Source 2 send multicast data to multicast groups 224.1.1.1 and 225.1.1.1, respectively.

· Host A and Host C are receivers of multicast group 224.1.1.1, and Host B and Host D are receivers of multicast group 225.1.1.1.

· All host receivers run IGMPv2, and all devices run IGMPv2 snooping. Device A (which is close to the multicast sources) acts as the IGMP snooping querier.

Configure the devices to meet the following requirements:

· To prevent the devices from flooding unknown data in the VLAN, enable all the devices to drop unknown multicast data.

· A device does not mark a port that receives an IGMP query with source IP address 0.0.0.0 as a dynamic router port. This adversely affects the establishment of Layer 2 forwarding entries and multicast traffic forwarding. To avoid this, configure the source IP address of IGMP queries as a non-zero IP address.

Figure 6 Network diagram

‌

Prerequisites

By default, interfaces on the device are disabled (in ADM or Administratively Down state). To have an interface operate, you must use the undo shutdown command to enable that interface.

Procedure

1. Configure Device A:

# Enable IGMP snooping globally.

<DeviceA> system-view

[DeviceA] igmp-snooping

[DeviceA-igmp-snooping] quit

# Create VLAN 100, and assign HundredGigE 1/0/1 through HundredGigE 1/0/3 to the VLAN.

[DeviceA] vlan 100

[DeviceA-vlan100] port hundredgige 1/0/1 to hundredgige 1/0/3

# Enable IGMP snooping, and enable dropping unknown multicast data for VLAN 100.

[DeviceA-vlan100] igmp-snooping enable

[DeviceA-vlan100] igmp-snooping drop-unknown

# Configure Device A as the IGMP snooping querier.

[DeviceA-vlan100] igmp-snooping querier

[DeviceA-vlan100] quit

# In VLAN 100, specify 192.168.1.1 as the source IP address of IGMP general queries.

[DeviceA-vlan100] igmp-snooping general-query source-ip 192.168.1.1

# In VLAN 100, specify 192.168.1.1 as the source IP address of IGMP group-specific queries.

[DeviceA-vlan100] igmp-snooping special-query source-ip 192.168.1.1

[DeviceA-vlan100] quit

2. Configure Device B:

# Enable IGMP snooping globally.

<DeviceB> system-view

[DeviceB] igmp-snooping

[DeviceB-igmp-snooping] quit

# Create VLAN 100, and assign HundredGigE 1/0/1 through HundredGigE 1/0/4 to the VLAN.

[DeviceB] vlan 100

[DeviceB-vlan100] port hundredgige 1/0/1 to hundredgige 1/0/4

# Enable IGMP snooping, and enable dropping unknown multicast data for VLAN 100.

[DeviceB-vlan100] igmp-snooping enable

[DeviceB-vlan100] igmp-snooping drop-unknown

[DeviceB-vlan100] quit

3. Configure Device C:

# Enable IGMP snooping globally.

<DeviceC> system-view

[DeviceC] igmp-snooping

[DeviceC-igmp-snooping] quit

# Create VLAN 100, and assign HundredGigE 1/0/1 through HundredGigE 1/0/3 to the VLAN.

[DeviceC] vlan 100

[DeviceC-vlan100] port hundredgige 1/0/1 to hundredgige 1/0/3

# Enable IGMP snooping, and enable dropping unknown multicast data for VLAN 100.

[DeviceC-vlan100] igmp-snooping enable

[DeviceC-vlan100] igmp-snooping drop-unknown

[DeviceC-vlan100] quit

4. Configure Device D:

# Enable IGMP snooping globally.

<SwitchD> system-view

[SwitchD] igmp-snooping

[SwitchD-igmp-snooping] quit

# Create VLAN 100, and assign HundredGigE 1/0/1 and HundredGigE 1/0/2 to the VLAN.

[SwitchD] vlan 100

[SwitchD-vlan100] port hundredgige 1/0/1 to hundredgige 1/0/2

# Enable IGMP snooping, and enable dropping unknown multicast data for VLAN 100.

[SwitchD-vlan100] igmp-snooping enable

[DeviceD-vlan100] igmp-snooping drop-unknown

[SwitchD-vlan100] quit

Verifying the configuration

# Display statistics for IGMP messages and PIMv2 hello messages learned through IGMP snooping on Device B.

[DeviceB] display igmp-snooping statistics

Received IGMP general queries: 3

Received IGMPv1 reports: 0

Received IGMPv2 reports: 12

Received IGMP leaves: 0

Received IGMPv2 specific queries: 0

Sent IGMPv2 specific queries: 0

Received IGMPv3 reports: 0

Received IGMPv3 reports with right and wrong records: 0

Received IGMPv3 specific queries: 0

Received IGMPv3 specific sg queries: 0

Sent IGMPv3 specific queries: 0

Sent IGMPv3 specific sg queries: 0

Received PIMv2 hello: 0

Received error IGMP messages: 0

The output shows that all devices except Device A can receive the IGMP general queries after Device A acts as the IGMP snooping querier.

Example: Configuring VLAN-based IGMP snooping proxying

Network configuration

As shown in Figure 7, Router A runs IGMPv2 and acts as the IGMP querier. Device A runs IGMPv2 snooping. Configure IGMP snooping proxying so that Device A can perform the following actions:

· Forward IGMP report and leave messages to Router A.

· Respond to IGMP queries sent by Router A and forward the queries to downstream hosts.

Figure 7 Network diagram

‌

Prerequisites

By default, interfaces on the device are disabled (in ADM or Administratively Down state). To have an interface operate, you must use the undo shutdown command to enable that interface.

Assign an IP address and subnet mask to each interface.

Procedure

1. Configure Router A:

# Enable IP multicast routing.

<RouterA> system-view

[RouterA] multicast routing

[RouterA-mrib] quit

# Enable IGMP and PIM-DM on HundredGigE 1/0/1.

[RouterA] interface hundredgige 1/0/1

[RouterA-HundredGigE1/0/1] igmp enable

[RouterA-HundredGigE1/0/1] pim dm

[RouterA-HundredGigE1/0/1] quit

# Enable PIM-DM on HundredGigE 1/0/2.

[RouterA] interface hundredgige 1/0/2

[RouterA-HundredGigE1/0/2] pim dm

[RouterA-HundredGigE1/0/2] quit

2. Configure Device A:

# Enable IGMP snooping globally.

<DeviceA> system-view

[DeviceA] igmp-snooping

[DeviceA-igmp-snooping] quit

# Create VLAN 100, and assign HundredGigE 1/0/1 through HundredGigE 1/0/4 to the VLAN.

[DeviceA] vlan 100

[DeviceA-vlan100] port hundredgige 1/0/1 to hundredgige 1/0/4

# Enable IGMP snooping and IGMP snooping proxying for the VLAN.

[DeviceA-vlan100] igmp-snooping enable

[DeviceA-vlan100] igmp-snooping proxy enable

[DeviceA-vlan100] quit

Verifying the configuration

# Send IGMP reports from Host A and Host B to join multicast groups 224.1.1.1 and 224.1.1.1. (Details not shown.)

# Display brief information about IGMP snooping group entries on Device A.

[DeviceA] display igmp-snooping group

Total 1 entries.

VLAN 100: Total 1 entries.

(0.0.0.0, 224.1.1.1)

Host ports (2 in total):

HGE1/0/3 (00:04:00)

HGE1/0/4 (00:04:04)

The output shows that HundredGigE1/0/3 and HundredGigE1/0/4 are member ports of multicast group 224.1.1.1. Host A and Host B become receivers of the group.

# Display IGMP group membership information on Router A.

[RouterA] display igmp group

IGMP groups in total: 1

HundredGigE1/0/1(10.1.1.1):

IGMP groups reported in total: 1

Group address Last reporter Uptime Expires

224.1.1.1 0.0.0.0 00:00:31 00:02:03

# Send an IGMP leave message from Host A to leave multicast group 224.1.1.1. (Details not shown.)

# Display brief information about IGMP snooping group entries on Device A.

[DeviceA] display igmp-snooping group

Total 1 entries.

VLAN 100: Total 1 entries.

(0.0.0.0, 224.1.1.1)

Host ports (1 in total):

HGE1/0/3 ( 00:01:23 )

The output shows that HundredGigE1/0/3 is the only member port of multicast group 224.1.1.1. Only Host B remains as the receiver of the group.

Troubleshooting IGMP snooping

Layer 2 multicast forwarding cannot function

Symptom

Layer 2 multicast forwarding cannot function on the Layer 2 device.

Solution

To resolve the issue:

1. Use the display igmp-snooping command to display IGMP snooping status.

2. If IGMP snooping is not enabled, use the igmp-snooping command in system view to enable IGMP snooping globally. Then, use the igmp-snooping enable command in VLAN view to enable IGMP snooping for the VLAN.

3. If IGMP snooping is enabled globally but not enabled for the VLAN, use the igmp-snooping enable command in VLAN view to enable IGMP snooping for the VLAN.

4. If the issue persists, contact H3C Support.

Multicast group policy does not work

Symptom

Hosts can receive multicast data for multicast groups that are not permitted by the multicast group policy.

Solution

To resolve the issue:

1. Use the display acl command to verify that the configured ACL meets the multicast group policy requirements.

2. Use the display this command in IGMP-snooping view or in a corresponding interface view to verify that the correct multicast group policy has been applied. If the applied policy is not correct, use the group-policy or igmp-snooping group-policy command to apply the correct multicast group policy.

3. Use the display igmp-snooping command to verify that dropping unknown multicast data is enabled. If it is not, use the igmp-snooping drop-unknown command to enable dropping unknown multicast data.

4. If the issue persists, contact H3C Support.

05-IP Multicast Configuration Guide

About IGMP snooping

Router ports

Member ports

General query

IGMP report

Leave message

Protocols and standards

Enabling IGMP snooping

Enabling IGMP snooping for multiple VLANs

Specifying an IGMP snooping version

About this task

Specifying an IGMP snooping version for multiple VLANs

Specifying an IGMP snooping version for a VLAN

About this task

Procedure

About this task

Restrictions and guidelines

Configuring a static multicast MAC address entry in system view

Configuring a static multicast MAC address entry in interface view

About this task

Setting the IGMP last member query interval globally

Setting the IGMP last member query interval for a VLAN

Setting aging timers for dynamic ports

About this task

Restrictions and guidelines

Setting the aging timers for dynamic ports globally

Setting the aging timers for dynamic ports in a VLAN

About this task

Procedure

About this task

Procedure

Configuring a port as a simulated member host

About this task

Procedure

About this task

Restrictions and guidelines

Enabling fast-leave processing on a port

Configuring the IGMP snooping querier

Enabling the IGMP snooping querier

Restrictions and guidelines

Enabling the IGMP snooping querier for a VLAN

About this task

Restrictions and guidelines

Configuring parameters for IGMP general queries and responses globally

Configuring source IP addresses for IGMP messages

About this task

Configuring the source IP addresses for IGMP messages in a VLAN

About this task

Setting the 802.1p priority for IGMP messages globally

Setting the 802.1p priority for IGMP messages in a VLAN

Configuring IGMP snooping policies

Configuring a multicast group policy

About this task

Configuring a multicast group policy globally

Configuring a multicast group policy on a port

Enabling multicast source port filtering

About this task

Restrictions and guidelines

Enabling multicast source port filtering in IGMP-snooping view

Enabling multicast source port filtering in interface view

About this task

Restrictions and guidelines

Enabling dropping unknown multicast data for a VLAN

Enabling IGMP report suppression

About this task

Procedure

About this task

Procedure

About this task

Enabling host tracking globally

Enabling host tracking for a VLAN

IGMP snooping configuration examples

Network configuration

Prerequisites

Procedure

Verifying the configuration

Network configuration

Prerequisites

Procedure