For this command to take effect, you must map the Layer 3 interface to a VSI. If you modify the VSI mapping, packet statistics of the interface are cleared.

Examples

# Map GigabitEthernet 1/0 to VSI vsia and enable packet statistics on the interface.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0

[Sysname-GigabitEthernet1/0] xconnect vsi vsia

[Sysname-GigabitEthernet1/0] ac statistics enable

Related commands

display l2vpn interface verbose

reset l2vpn statistics ac

arp suppression enable

Use arp suppression enable to enable ARP flood suppression.

Use undo arp suppression enable to disable ARP flood suppression.

Syntax

arp suppression enable

undo arp suppression enable

Default

ARP flood suppression is disabled.

Views

VSI view

Predefined user roles

network-admin

Usage guidelines

ARP flood suppression reduces ARP request broadcasts by enabling the VTEP to reply to ARP requests on behalf of VMs.

This feature snoops ARP packets to populate the ARP flood suppression table with local and remote MAC addresses. If an ARP request has a matching entry, the VTEP replies to the request on behalf of the VM. If no match is found, the VTEP floods the request to both local and remote sites.

Examples

# Enable ARP flood suppression for VSI vsi1.

<Sysname> system-view

[Sysname] vsi vsi1

[Sysname-vsi-vsi1] arp suppression enable

Related commands

display arp suppression vsi

reset arp suppression vsi

description

Use description to configure a description for a VSI.

Use undo description to restore the default.

Syntax

description text

undo description

Default

A VSI does not have a description.

Views

VSI view

Predefined user roles

network-admin

mdc-admin

Parameters

text: Specifies a description, a case-sensitive string of 1 to 80 characters.

Examples

# Configure a description for VSI vpn1.

<Sysname> system-view

[Sysname] vsi vpn1

[Sysname-vsi-vpn1] description vsi for vpn1

Related commands

display l2vpn vsi

display arp suppression vsi

Use display arp suppression vsi to display ARP flood suppression entries.

Syntax

In standalone mode:

display arp suppression vsi [ name vsi-name ] [ count ]

In IRF mode:

display arp suppression vsi [ name vsi-name ] [ slot slot-number ] [ count ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

name vsi-name: Specifies a VSI by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VSI, this command displays entries for all VSIs.

slot slot-number: Specifies an IRF member device by its member ID. If you do not specify a member device, this command displays entries on the master device. (In IRF mode.)

count: Displays the number of ARP flood suppression entries that match the command.

Examples

# Display ARP flood suppression entries.

<Sysname> display arp suppression vsi

IP address MAC address Vsi Name Link ID Aging

1.1.1.2 000f-e201-0101 vsi1 0x70000 14

1.1.1.3 000f-e201-0202 vsi1 0x80000 18

1.1.1.4 000f-e201-0203 vsi2 0x90000 10

# Display the number of ARP flood suppression entries.

<Sysname> display arp suppression vsi count

Total entries: 3

Table 1 Command output

Field	Description
Link ID	Link ID that uniquely identifies an AC or a VXLAN tunnel on a VSI.
Aging	Remaining lifetime (in minutes) of the ARP flood suppression entry. When the timer expires, the entry is deleted.

Related commands

arp suppression enable

reset arp suppression vsi

display l2vpn interface

Use display l2vpn interface to display L2VPN information for Layer 3 interfaces that are mapped to VSIs.

Syntax

display l2vpn interface [ vsi vsi-name | interface-type interface-number ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

vsi vsi-name: Specifies a VSI name, a case-sensitive string of 1 to 31 characters.

interface-type interface-number: Specifies an interface by its type and number.

verbose: Displays detailed information about Layer 3 interfaces. If you do not specify this keyword, the command displays brief information about Layer 3 interfaces.

Usage guidelines

If you do not specify any parameters, this command displays brief L2VPN information for all Layer 3 interfaces that are mapped to VSIs.

Examples

# Display brief L2VPN information for all Layer 3 interfaces that are mapped to VSIs.

<Sysname> display l2vpn interface

Total number of interfaces: 2, 1 up, 1 down

Interface Owner Link ID State Type

GE1/0 vxlan3 1 Up VSI

GE2/0 vxlan4 2 Down VSI

Table 2 Command output

Field	Description
Interface	Layer 3 interface name.
Owner	VSI name.
Link ID	The interface's link ID on the VSI.
State	Physical state of the interface: · Up—The interface is physically up. · Down—The interface is physically down.
Type	L2VPN type of the interface. This field displays VSI for the VXLAN feature.

# Display detailed L2VPN information for all Layer 3 interfaces that are mapped to VSIs.

<Sysname> display l2vpn interface verbose

Interface: GE1/0

Owner : vsi1

Link ID : 0

State : Up

Type : VSI

Statistics : Enabled

Input Statistics:

Octets :994496

Packets :15539

Output Statistics:

Octets :0

Packets :0

Interface: GE2/0

Owner : vsi2

Link ID : 0

State : Down

Type : VSI

Statistics : Enabled

Input Statistics:

Octets :0

Packets :0

Output Statistics:

Octets :0

Packets :0

Table 3 Command output

Field	Description
Interface	Layer 3 interface name.
Owner	VSI name.
Link ID	The interface's link ID on the VSI.
State	Physical state of the interface: · Up—The interface is physically up. · Down—The interface is physically down.
Type	L2VPN type of the interface. This field displays VSI for the VXLAN feature.
Statistics	Packet statistics state: · Enabled—The packet statistics feature is enabled for the interface. · Disabled—The packet statistics feature is disabled for the interface.
Input Statistics	Incoming traffic statistics: · Octets—Number of incoming bytes. · Packets—Number of incoming packets.
Output Statistics	Outgoing traffic statistics: · Octets—Number of outgoing bytes. · Packets—Number of outgoing packets.

display l2vpn mac-address

Use display l2vpn mac-address to display MAC address entries for VSIs.

Syntax

display l2vpn mac-address [ vsi vsi-name ] [ dynamic ] [ count ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

vsi vsi-name: Specifies a VSI name, a case-sensitive string of 1 to 31 characters. If you do not specify a VSI, this command displays MAC address entries for all VSIs.

dynamic: Specifies dynamic MAC address entries learned in the data plane. If you do not specify this keyword, the command displays all MAC address entries, including:

· Dynamic remote- and local-MAC entries.

· Remote-MAC entries advertised through BGP EVPN.

· Manually added static remote-MAC entries.

· Remote-MAC entries issued through OpenFlow.

· Remote-MAC entries issued through OVSDB.

VXLAN does not support static local-MAC entries.

count: Displays the number of MAC address entries. If you do not specify this keyword, the command displays detailed information about MAC address entries.

Examples

# Display MAC address entries for all VSIs.

<Sysname> display l2vpn mac-address

MAC Address State VSI Name Link ID/Name Aging

0000-0000-000b Static vpn1 Tunnel10 NotAging

0000-0000-000c Dynamic vpn1 Tunnel60 Aging

0000-0000-000d Dynamic vpn1 Tunnel99 Aging

--- 3 mac address(es) found ---

# Display the total number of MAC address entries in all VSIs.

<Sysname> display l2vpn mac-address count

3 mac address(es) found

Table 4 Command output

Field	Description
State	Entry state: · Dynamic—Local- or remote-MAC entry dynamically learned in the data plane. · Static—Static remote-MAC entry. · EVPN—Remote-MAC entry advertised through BGP EVPN. · OpenFlow—Remote-MAC entry issued by a remote controller through OpenFlow. · OVSDB—Remote-MAC entry issued by a remote controller through OVSDB.
Link ID/Name	For a local MAC address, this field displays the AC's link ID on the VSI. For a remote MAC address, this field displays the tunnel interface name.
Aging	Entry aging state: · Aging. · NotAging.

Related commands

reset l2vpn mac-address

display l2vpn vsi

Use display l2vpn vsi to display information about VSIs.

Syntax

display l2vpn vsi [ name vsi-name ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

name vsi-name: Specifies a VSI by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VSI, this command displays information about all VSIs.

verbose: Displays detailed information about VSIs. If you do not specify this keyword, the command displays brief information about VSIs.

Examples

# Display brief information about all VSIs.

<Sysname> display l2vpn vsi

Total number of VSIs: 1, 1 up, 0 down, 0 admin down

VSI Name VSI Index MTU State

vpna 0 1500 Up

Table 5 Command output

Field	Description
MTU	MTU on the VSI.
State	VSI state: · Up—The VSI is up. · Down—The VSI is down. · Admin down—The VSI has been manually shut down by using the shutdown command.

Field

Description

MTU

MTU on the VSI.

State

VSI state:

· Up—The VSI is up.

· Down—The VSI is down.

· Admin down—The VSI has been manually shut down by using the shutdown command.

# Display detailed information about all VSIs.

<Sysname> display l2vpn vsi verbose

VSI Name: vpna

VSI Index : 0

VSI State : Up

MTU : 1500

Bandwidth : -

Broadcast Restrain : -

Multicast Restrain : -

Unknown Unicast Restrain: -

MAC Learning : Enabled

MAC Table Limit : -

MAC Leacning rate ：-

Drop Unknown : -

PW Redundancy : Slave

Flooding : Enabled

Statistics : Enabled

Input Statistics:

Octets : 0

Packets : 0

Errors : 0

Discards : 0

Output Statistics:

Octets : 0

Packets : 0

Errors : 0

Discards : 0

Gateway Interface : VSI-interface 100

VXLAN ID : 10

Tunnels:

Tunnel Name Link ID State Type Flood Proxy Split horizon

Tunnel1 0x5000001 Up Manual Disabled Enabled

Tunnel2 0x5000002 Up Manual Disabled Enabled

ACs:

AC Link ID State

GE1/0 0 Up

Table 6 Command output

Field	Description
VSI Description	Description of the VSI. If the VSI does not have a description, the command does not display this field.
VSI State	VSI state: · Up—The VSI is up. · Down—The VSI is down. · Administratively down—The VSI has been manually shut down by using the shutdown command.
MTU	MTU on the VSI.
Bandwidth	Maximum bandwidth (in kbps) for known unicast traffic on the VSI. This field displays a hyphen (-) if it is not available in the current software version.
Broadcast Restrain	Broadcast restraint bandwidth (in kbps). This field displays a hyphen (-) if it is not available in the current software version.
Multicast Restrain	Multicast restraint bandwidth (in kbps). This field displays a hyphen (-) if it is not available in the current software version.
Unknown Unicast Restrain	Unknown unicast restraint bandwidth (in kbps). This field displays a hyphen (-) if it is not available in the current software version.
MAC Learning	State of the MAC learning feature.
MAC Table Limit	Maximum number of MAC address entries on the VSI. This field displays a hyphen (-) if it is not available in the current software version.
Drop Unknown	Action on source MAC-unknown frames received after the maximum number of MAC entries is reached. · Enabled—Drops the frames. · Disabled—Forwards the frames without learning the source MAC address.
Flooding	State of the VSI's flooding feature: · Enabled—Flooding is enabled on the VSI. The VTEP floods unknown unicast frames to both local and remote sites. · Disabled—Flooding is disabled on the VSI. The VTEP floods unknown unicast frames only to local sites.
Statistics	Packet statistics state: · Enabled—The packet statistics feature is enabled for the VSI. · Disabled—The packet statistics feature is disabled for the VSI.
Input Statistics	Incoming traffic statistics: · Octets—Number of incoming bytes. · Packets—Number of incoming packets. · Errors—Number of error packets. · Discards—Number of discarded packets.
Output Statistics	Outgoing traffic statistics: · Octets—Number of outgoing bytes. · Packets—Number of outgoing packets. · Errors—Number of error packets. · Discards—Number of discarded packets.
Gateway Interface	VSI interface name.
State	Tunnel state: · Up—The tunnel is operating correctly. · Blocked—The tunnel is a backup proxy tunnel. Its tunnel interface is up, but the tunnel is blocked because the primary proxy tunnel is operating correctly. ‌ · Defect—The tunnel interface is up, but BFD cannot detect the remote VTEP. This state is not supported in the current software version. · Down—The tunnel interface is down.
Type	Tunnel assignment method: · Auto—The tunnel was automatically assigned to the VXLAN through EVPN. · Manual—The tunnel was manually assigned to the VXLAN.
Flood Proxy	Flood proxy state: · Enabled—Flood proxy is enabled. The VTEP sends broadcast, multicast, and unknown unicast traffic to a flood proxy server through the tunnel. The flood proxy server replicates and forwards flood traffic to remote VTEPs. · Disabled—Flood proxy is disabled.
Split horizon	State of split horizon: · Enabled—Split horizon is enabled on the VXLAN tunnel. The VXLAN tunnel does not forward the traffic that is received on other VXLAN tunnels. · Disabled—Split horizon is disabled on the VXLAN tunnel. The VXLAN tunnel forwards the traffic that is received on ACs and other VXLAN tunnels.
ACs	ACs that are bound to the VSI.
Link ID	AC's link ID on the VSI.
State	AC state: · Up. · Down.

display vxlan tunnel

Use display vxlan tunnel to display VXLAN tunnel information for VXLANs.

Syntax

display vxlan tunnel [ vxlan-id vxlan-id [ tunnel tunnel-number ] ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

vxlan-id: Specifies a VXLAN ID in the range of 0 to 16777215. If you do not specify a VXLAN, this command displays VXLAN tunnel information for all VXLANs.

tunnel tunnel-number: Specifies a VXLAN tunnel. The tunnel-number argument represents the tunnel interface number. The value range for the tunnel-number argument is 0 to 65534. If you do not specify a VXLAN tunnel, this command displays information about all VXLAN tunnels associated with the specified VXLAN.

Examples

# Display VXLAN tunnel information for all VXLANs.

<Sysname> display vxlan tunnel

Total number of VXLANs: 1

VXLAN ID: 10, VSI name: vpna, Total tunnels: 3 (3 up, 0 down, 0 defect, 0 blocked)

Tunnel name Link ID State Type Flood proxy Split horizon

Tunnel1 0x5000001 Up Manual Disabled Enabled

Tunnel2 0x5000002 Up Manual Disabled Enabled

# Display VXLAN tunnel information for VXLAN 10.

<Sysname> display vxlan tunnel vxlan-id 10

VXLAN ID: 10, VSI name: vpna, Total tunnels: 3 (3 up, 0 down, 0 defect, 0 blocked)

Tunnel name Link ID State Type Flood proxy Split horizon

Tunnel1 0x5000001 Up Manual Disabled Enabled

Tunnel2 0x5000002 Up Manual Disabled Enabled

# Display information about VXLAN tunnel 0 for VXLAN 10.

<Sysname> display vxlan tunnel vxlan-id 10 tunnel 0

Interface: Tunnel0

Link ID : 0x5000000

State : Up

Type : Auto

Flood Proxy: Disabled

Statistics : Enabled

Input statistics:

Octets : 994496

Packets: 15539

Output statistics:

Octets : 0

Packets: 0

Table 7 Command output

Field	Description
Link ID	Tunnel's link ID in the VXLAN.
State	Tunnel state: · Up—The tunnel is operating correctly. · Blocked—The tunnel is a backup proxy tunnel. Its tunnel interface is up, but the tunnel is blocked because the primary proxy tunnel is operating correctly. ‌ · Down—The tunnel interface is down.
Type	Tunnel assignment method: · Auto—The tunnel was automatically assigned to the VXLAN through EVPN. · Manual—The tunnel was manually assigned to the VXLAN.
Flood proxy	Flood proxy state: · Enabled—Flood proxy is enabled. The VTEP sends broadcast, multicast, and unknown unicast traffic to a flood proxy server through the tunnel. The flood proxy server replicates and forwards flood traffic to remote VTEPs. · Disabled—Flood proxy is disabled.
Split horizon	State of split horizon: · Enabled—Split horizon is enabled on the VXLAN tunnel. The VXLAN tunnel does not forward the traffic that is received on other VXLAN tunnels. · Disabled—Split horizon is disabled on the VXLAN tunnel. The VXLAN tunnel forwards the traffic that is received on ACs and other VXLAN tunnels.

‌

Related commands

tunnel

vxlan

flooding disable

Use flooding disable to disable flooding for a VSI.

Use undo flooding disable to enable flooding for a VSI.

Syntax

flooding disable

undo flooding disable

Default

Flooding is enabled for a VSI.

Views

VSI view

Predefined user roles

network-admin

Usage guidelines

By default, the device floods unknown unicast frames received from the local site to the following interfaces in the frame's VXLAN:

· All site-facing interfaces except for the incoming interface.

· All VXLAN tunnel interfaces.

To confine unknown unicast traffic to the site-facing interfaces, use this command to disable flooding for the VSI bound to the VXLAN. The VSI will not flood unknown unicast frames to VXLAN tunnel interfaces.

Examples

# Disable flooding for VSI vsi1.

<Sysname> system-view

[Sysname] vsi vsi1

[Sysname-vsi-vsi1] flooding disable

l2vpn enable

Use l2vpn enable to enable L2VPN.

Use undo l2vpn enable to disable L2VPN.

Syntax

l2vpn enable

undo l2vpn enable

Default

L2VPN is disabled.

Views

System view

Predefined user roles

network-admin

Usage guidelines

You must enable L2VPN before you can configure L2VPN settings.

Examples

# Enable L2VPN.

<Sysname> system-view

[Sysname] l2vpn enable

l2vpn rewrite inbound tag

Use l2vpn rewrite inbound tag to configure the VLAN tag processing rule for incoming traffic.

Use undo l2vpn rewrite inbound to restore the default.

Syntax

l2vpn rewrite inbound tag { nest { c-vid vlan-id | s-vid vlan-id [ c-vid vlan-id ] } | remark 1-to-2 s-vid vlan-id c-vid vlan-id } [ symmetric ]

undo l2vpn rewrite inbound

Default

VLAN tags of incoming traffic are not processed.

Views

Layer 3 aggregate interface view

Layer 3 Ethernet interface view

Predefined user roles

network-admin

Parameters

nest: Adds VLAN tags.

c-vid: Specifies an inner VLAN tag.

s-vid: Specifies an outer VLAN tag.

vlan-id: Specifies a VLAN ID in the range of 1 to 4094.

remark: Maps VLAN tags.

1-to-2: Performs one-to-two mapping to replace the VLAN tag of single tagged packets with the specified outer and inner VLAN tags.

symmetric: Applies the reverse VLAN tag processing rule to outgoing traffic. If you do not specify this keyword, VLAN tags of outgoing traffic are not processed.

Usage guidelines

To modify the VLAN tag processing rule for incoming traffic, first execute the undo l2vpn rewrite inbound command to remove the existing rule, and then execute the l2vpn rewrite inbound command.

When you use this command, follow these restrictions:

· The l2vpn rewrite inbound tag nest s-vid vlan-id c-vid vlan-id command takes effect only on untagged packets.

· The l2vpn rewrite inbound tag remark 1-to-2 command takes effect only on single tagged packets.

Examples

# Configure Layer 3 Ethernet interface GigabitEthernet 1/0 to add outer VLAN tag 100 to incoming frames and remove outer VLAN tag 100 from outgoing frames.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0

[Sysname-GigabitEthernet1/0] l2vpn rewrite inbound tag nest s-vid 100 symmetric

mac-address static vsi

Use mac-address static vsi to add a static remote-MAC address entry for a VXLAN VSI.

Use undo mac-address static vsi to remove static remote-MAC address entries for a VXLAN VSI.

Syntax

mac-address static mac-address interface tunnel tunnel-number vsi vsi-name

undo mac-address static [ mac-address ] [ interface tunnel tunnel-number ] vsi vsi-name

Default

VXLAN VSIs do not have static remote-MAC address entries.

Views

System view

Predefined user roles

network-admin

Parameters

mac-address: Specifies a MAC address in H-H-H format. Do not specify a multicast MAC address or an all-zeros MAC address. You can omit the consecutive zeros at the beginning of each segment. For example, you can enter f-e2-1 for 000f-00e2-0001.

interface tunnel tunnel-number: Specifies a VXLAN tunnel interface by its tunnel interface number. The value range for the tunnel-number argument is 0 to 65534.

vsi vsi-name: Specifies a VSI name, a case-sensitive string of 1 to 31 characters.

Usage guidelines

A remote MAC address is the MAC address of a VM in a remote site. Remote MAC entries include manually added MAC entries, dynamically learned MAC entries, and MAC entries advertised through a protocol, for example, BGP EVPN.

When you add a remote MAC address entry, make sure the specified VSI's VXLAN has been assigned the specified VXLAN tunnel.

The undo mac-address static vsi vsi-name command removes all static MAC address entries for a VSI.

Do not configure static remote-MAC entries for tunnels that are automatically established by using EVPN.

· EVPN re-establishes tunnels if the transport-facing interface goes down and then comes up. If you have configured static remote-MAC entries, the entries are deleted when the tunnels are re-established.

· EVPN re-establishes tunnels if you perform configuration rollback. If the tunnel IDs change during tunnel re-establishment, configuration rollback fails, and static remote-MAC entries on the tunnels cannot be restored.

Examples

# Add MAC address 000f-e201-0101 to VSI vsi1. Specify Tunnel-interface 1 as the outgoing interface.

<Sysname> system-view

[Sysname] mac-address static 000f-e201-0101 interface tunnel 1 vsi vsi1

Related commands

vxlan tunnel mac-learning disable

mtu

Use mtu to set the MTU for a VSI.

Use undo mtu to restore the default.

Syntax

mtu size

undo mtu

Default

The default MTU of a VSI is 1500 bytes.

Views

VSI view

Predefined user roles

network-admin

Parameters

size: Specifies an MTU value. The value range for this argument is 46 to 9216.

Usage guidelines

The MTU set by using this command limits the maximum length of the packets that a VSI receives from ACs and forwards through VXLAN tunnels. The MTU does not limit the maximum length of other packets in the VXLAN VSI.

Fragmentation is disabled for a VSI that uses the default MTU. If you set a MTU for a VSI, the packets longer than the MTU are fragmented.

Examples

# Set the MTU to 1400 bytes for VSI vxlan1.

<Sysname> system-view

[Sysname] vsi vxlan1

[Sysname-vsi-vxlan1] mtu 1400

Related commands

display l2vpn vsi

reserved vxlan

Use reserved vxlan to specify a reserved VXLAN.

Use undo reserved vxlan to restore the default.

Syntax

reserved vxlan vxlan-id

undo reserved vxlan

Default

No VXLAN has been reserved.

Views

System view

Predefined user roles

network-admin

Parameters

vxlan-id: Specifies a VXLAN ID in the range of 0 to 16777215.

Usage guidelines

You can specify only one reserved VXLAN on the VTEP. The reserved VXLAN cannot be the VXLAN created on any VSI.

The reserved VXLAN ID cannot be the same as the remote VXLAN ID specified by using the mapping vni command.

Examples

# Specify VXLAN 10000 as the reserved VXLAN.

<Sysname> system-view

[Sysname] reserved vxlan 10000

Related commands

mapping vni (EVPN Command Reference)

reset arp suppression vsi

Use reset arp suppression vsi to clear ARP flood suppression entries on VSIs.

Syntax

reset arp suppression vsi [ name vsi-name ]

Views

User view

Predefined user roles

network-admin

Parameters

name vsi-name: Specifies a VSI by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VSI, this command clears ARP flood suppression entries on all VSIs.

Examples

# Clear ARP flood suppression entries on all VSIs.

<Sysname> reset arp suppression vsi

This command will delete all entries. Continue? [Y/N]:y

Related commands

arp suppression enable

display arp suppression vsi

reset l2vpn mac-address

Use reset l2vpn mac-address to clear dynamic MAC address entries on VSIs.

Syntax

reset l2vpn mac-address [ vsi vsi-name ]

Views

User view

Predefined user roles

network-admin

Parameters

vsi vsi-name: Specifies a VSI by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VSI, this command clears all dynamic MAC address entries on all VSIs.

Usage guidelines

Use this command when the number of dynamic MAC address entries reaches the limit or the device learns incorrect MAC addresses.

Examples

# Clear the dynamic MAC address entries on VSI vpn1.

<Sysname> reset l2vpn mac-address vsi vpn1

Related commands

display l2vpn mac-address vsi

reset l2vpn statistics ac

Use reset l2vpn statistics ac to clear packet statistics on ACs.

Syntax

reset l2vpn statistics ac [ interface interface-type interface-number ]

Views

User view

Predefined user roles

network-admin

Parameters

interface interface-type interface-number: Specifies an interface by its type and number.

Usage guidelines

If you do not specify any parameters, this command clears packet statistics on all ACs.

Examples

# Clear packet statistics for Layer 3 interface GigabitEthernet 1/0.

<Sysname> reset l2vpn statistics ac interface gigabitethernet 1/0

Related commands

ac statistics enable

display l2vpn interface

reset l2vpn statistics vsi

Use reset l2vpn statistics vsi to clear packet statistics on VSIs.

Syntax

reset l2vpn statistics vsi [ name vsi-name ]

Views

User view

Predefined user roles

network-admin

Parameters

name vsi-name: Specifies a VSI by its name, a case-sensitive string of 1 to 31 characters. If you do not specify a VSI, this command clears packet statistics on all VSIs.

Examples

# Clear packet statistics on all VSIs.

<Sysname> reset l2vpn statistics vsi

Related commands

statistics enable (VSI view)

selective-flooding mac-address

Use selective-flooding mac-address to enable selective flood for a MAC address.

Use undo selective-flooding mac-address to disable selective flood for a MAC address.

Syntax

selective-flooding mac-address mac-address

undo selective-flooding mac-address mac-address

Default

Selective flood is disabled for all MAC addresses.

Views

VSI view

Predefined user roles

network-admin

Parameters

mac-address: Specifies a MAC address. The MAC address cannot be all Fs.

Usage guidelines

This command excludes a remote MAC address from the flood suppression done by using the flooding disable command. The VTEP will flood the frames destined for the specified MAC address to remote sites when unknown-unicast floods are confined to the local site.

Examples

# Enable selective flood for 000f-e201-0101 on VSI vsi1.

<Sysname> system-view

[Sysname] vsi vsi1

[Sysname-vsi-vsi1] selective-flooding mac-address 000f-e201-0101

Related commands

flooding disable

shutdown

Use shutdown to shut down a VSI.

Use undo shutdown to bring up a VSI.

Syntax

shutdown

undo shutdown

Default

VSIs are not manually shut down.

Views

VSI view

Predefined user roles

network-admin

Usage guidelines

Use this command to temporarily disable a VSI to provide Layer 2 switching services. The shutdown action does not change settings on the VSI. You can continue to configure the VSI. After you bring up the VSI again, the VSI provides services based on the latest settings.

Examples

# Shut down VSI vpn1.

<Sysname> system-view

[Sysname] vsi vpn1

[Sysname-vsi-vpn1] shutdown

Related commands

display l2vpn vsi

tunnel

Use tunnel to assign a VXLAN tunnel to a VXLAN.

Use undo tunnel to remove a VXLAN tunnel from a VXLAN.

Syntax

tunnel tunnel-number { flooding-proxy | no-split-horizon }

undo tunnel tunnel-number

Default

A VXLAN does not contain VXLAN tunnels.

Views

VXLAN view

Predefined user roles

network-admin

Parameters

tunnel-number: Specifies a tunnel interface number. The value range for this argument is 0 to 65534. The tunnel must be a VXLAN tunnel.

flooding-proxy: Enables flood proxy on the tunnel for the VTEP to send flood traffic to the flood proxy server. The flood proxy server replicates and forwards flood traffic to remote VTEPs. If you do not specify this keyword, flood proxy is disabled on the tunnel.

no-split-horizon: Disables split horizon on the tunnel. The tunnel can forward the traffic that is received on ACs and other VXLAN tunnels. If you do not specify this keyword, split horizon is enabled on the tunnel, and it does not forward the traffic that is received on other VXLAN tunnels.

Usage guidelines

This command assigns a VXLAN tunnel to a VXLAN to provide Layer 2 connectivity for the VXLAN between two sites. In unicast mode, the system floods unknown unicast, multicast, and broadcast traffic to each tunnel in the VXLAN.

You can assign multiple VXLAN tunnels to a VXLAN, and configure a VXLAN tunnel to trunk multiple VXLANs.

On a VSI, you can enable flood proxy on multiple VXLAN tunnels. The first tunnel that is enabled with flood proxy works as the primary proxy tunnel to forward broadcast, multicast, and unknown unicast traffic. Other proxy tunnels are backups that do not forward traffic when the primary proxy tunnel is operating correctly.

If you disable split horizon on a VXLAN tunnel, make sure the corresponding VXLAN does not have another VXLAN tunnel that is destined for the same remote VTEP.

To modify the flood proxy or split horizon setting on a VXLAN tunnel, you must first use the undo tunnel command to remove the tunnel.

Examples

# Assign VXLAN tunnels 1 and 2 to VXLAN 10000.

<Sysname> system-view

[Sysname] vsi vpna

[Sysname-vsi-vpna] vxlan 10000

[Sysname-vsi-vpna-vxlan-10000] tunnel 1

[Sysname-vsi-vpna-vxlan-10000] tunnel 2

Related commands

display vxlan tunnel

tunnel bfd enable

Use tunnel bfd enable to enable BFD on a VXLAN tunnel interface.

Use undo tunnel bfd enable to disable BFD on a VXLAN tunnel interface.

Syntax

tunnel bfd enable destination-mac mac-address

undo tunnel bfd enable

Default

BFD is disabled on a VXLAN tunnel interface.

Views

VXLAN tunnel interface view

Predefined user roles

network-admin

Parameters

destination-mac mac-address: Specifies a destination MAC address in H-H-H format for BFD control packets. The MAC address can be a remote VTEP address or a multicast address. You can omit the consecutive zeros at the beginning of each segment. For example, you can enter f-e2-1 for 000f-00e2-0001.

Usage guidelines

Enable BFD on both ends of a VXLAN tunnel for quick link connectivity detection. The VTEPs periodically send BFD single-hop control packets to each other through the VXLAN tunnel. A VTEP sets the tunnel state to Defect if it has not received control packets from the remote end for 5 seconds. In this situation, the tunnel interface state is still Up. The tunnel state will change from Defect to Up if the VTEP can receive BFD control packets again.

Examples

# Enable BFD on VXLAN tunnel interface Tunnel 9, and specify 1-1-1 as the destination MAC address for BFD control packets.

<Sysname> system-view

[Sysname] interface tunnel 9 mode vxlan

[Sysname-Tunnel9] tunnel bfd enable destination-mac 1-1-1

tunnel global source-address

Use tunnel global source-address to specify a global source address for VXLAN tunnels.

Use undo tunnel global source-address to restore the default.

Syntax

tunnel global source-address { ipv4-address | ipv6 ipv6-address }

undo tunnel global source-address [ ipv6 ]

Default

No global source address is specified for VXLAN tunnels.

Views

System view

Predefined user roles

network-admin

Parameters

ipv4-address: Specifies an IPv4 address.

ipv6 ipv6-address: Specifies an IPv6 address. If you do not specify the ipv6 keyword when executing the undo tunnel global source-address command, the command deletes the global source IPv4 address for VXLAN tunnels.

Usage guidelines

IMPORTANT:

For correct VXLAN deployment and VTEP management, do not manually specify tunnel-specific source addresses for VXLAN tunnels if OVSDB is used.

‌

A VXLAN tunnel uses the global source address if you do not specify a source interface or source address for the tunnel.

The global source address takes effect only on VXLAN tunnels (excluding VXLAN-DCI tunnels).

IPv4 VXLAN tunnels use the global source IPv4 address, and IPv6 VXLAN tunnels use the global source IPv6 address.

Examples

# Specify 1.1.1.1 as the global source address for VXLAN tunnels.

<Sysname> system-view

[Sysname] tunnel global source-address 1.1.1.1

tunnel statistics enable

Use tunnel statistics enable to enable packet statistics for all VXLAN tunnels associated with a VSI.

Use undo tunnel statistics enable to disable packet statistics for all VXLAN tunnels associated with a VSI.

Syntax

tunnel statistics enable

undo tunnel statistics enable

Default

The packet statistics feature is disabled for the VXLAN tunnels associated with a VSI.

Views

VSI view

Predefined user roles

network-admin

Usage guidelines

This command enables packet statistics only for VXLAN tunnels. It does not take effect on VXLAN-DCI tunnels.

Examples

# Enable packet statistics for all VXLAN tunnels associated with VSI vpna.

<Sysname> system-view

[Sysname] vsi vpna

[Sysname-vsi-vpna] tunnel statistics enable

Related commands

display vxlan tunnel

vsi

Use vsi to create a VSI and enter its view, or enter the view of an existing VSI.

Use undo vsi to delete a VSI.

Syntax

vsi vsi-name

undo vsi vsi-name

Default

No VSIs exist.

Views

System view

Predefined user roles

network-admin

Parameters

vsi-name: Specifies a VSI name, a case-sensitive string of 1 to 31 characters.

Usage guidelines

A VSI acts as a virtual switch to provide Layer 2 switching services for a VXLAN on a VTEP. A VSI has all functions of a physical Ethernet switch, including source MAC address learning, MAC address aging, and flooding.

A VSI can provide services only for one VXLAN.

Examples

# Create VSI vxlan10 and enter VSI view.

<Sysname> system-view

[Sysname] vsi vxlan10

[Sysname-vsi-vxlan10]

Related commands

display l2vpn vsi

vxlan

Use vxlan to create a VXLAN and enter its view, or enter the view of an existing VXLAN.

Use undo vxlan to restore the default.

Syntax

vxlan vxlan-id

undo vxlan

Default

No VXLANs exist.

Views

VSI view

Predefined user roles

network-admin

Parameters

vxlan-id: Specifies a VXLAN ID in the range of 0 to 16777215.

Usage guidelines

You can create only one VXLAN for a VSI. The VXLAN ID for each VSI must be unique.

Examples

# Create VXLAN 10000 for VSI vpna and enter VXLAN view.

<Sysname> system-view

[Sysname] vsi vpna

[Sysname-vsi-vpna] vxlan 10000

[Sysname-vsi-vpna-vxlan-10000]

Related commands

vsi

vxlan fast-forwarding enable

Use vxlan fast-forwarding enable to enable VXLAN fast forwarding.

Use undo vxlan fast-forwarding enable to disable VXLAN fast forwarding.

Syntax

vxlan fast-forwarding enable

undo vxlan fast-forwarding enable

Default

VXLAN fast forwarding is disabled.

Views

System view

Predefined user roles

network-admin

Usage guidelines

VXLAN fast forwarding enables the device to bypass QoS and security services when the device forwards data traffic over VXLAN tunnels based on the software. As a best practice, enable this feature to improve forwarding speed only when QoS and security services are not configured on the following interfaces:

· VSI interfaces.

· VSI subinterfaces.

· Traffic outgoing interfaces for VXLAN tunnels.

When VXLAN fast forwarding is enabled, a VXLAN tunnel cannot use ECMP routes to load share traffic. Instead, it selects one route from the ECMP routes to forward VXLAN packets.

Examples

# Enable VXLAN fast forwarding.

<Sysname> system

[Sysname] vxlan fast-forwarding enable

vxlan invalid-udp-checksum discard

Use vxlan invalid-udp-checksum discard to enable the device to drop the VXLAN packets that fail UDP checksum check.

Use undo vxlan invalid-udp-checksum discard to restore the default.

Syntax

vxlan invalid-udp-checksum discard

undo vxlan invalid-udp-checksum discard

Default

The device does not check the UDP checksum of VXLAN packets.

Views

System view

Predefined user roles

network-admin

Usage guidelines

This command enables the device to check the UDP checksum of VXLAN packets.

The device always sets the UDP checksum of VXLAN packets to 0. For compatibility with third-party devices, a VXLAN packet can pass the check if its UDP checksum is 0 or correct. If its UDP checksum is incorrect, the VXLAN packet fails the check and is dropped.

Examples

# Enable the device to drop the VXLAN packets that fail UDP checksum check.

<Sysname> system-view

[Sysname] vxlan invalid-udp-checksum discard

vxlan local-mac report

Use vxlan local-mac report to enable local-MAC logging.

Use undo vxlan local-mac report to disable local-MAC logging.

Syntax

vxlan local-mac report

undo vxlan local-mac report

Default

Local-MAC logging is disabled.

Views

System view

Predefined user roles

network-admin

Usage guidelines

When the local-MAC logging feature is enabled, the VXLAN module immediately sends a log message with its local MAC addresses to the information center. When a local MAC address is added or removed, a log message is also sent to the information center to notify the local-MAC change.

With the information center, you can set log message filtering and output rules, including output destinations. For more information about configuring the information center, see Network Management and Monitoring Configuration Guide.

Examples

# Enable local-MAC logging.

<Sysname> system-view

[Sysname] vxlan local-mac report

vxlan source udp-port acl

Use vxlan source udp-port acl to configure an ACL match criterion and specify the source UDP port number in the VXLAN encapsulation for matching frames.

Use undo vxlan source udp-port to restore the default.

Syntax

vxlan source udp-port port-number acl acl-number

undo vxlan source udp-port

Default

The source UDP port number in the VXLAN encapsulation is generated based on the source and destination MAC addresses of the inner Ethernet frame.

Views

VXLAN tunnel interface view

VXLAN-DCI tunnel interface view

Predefined user roles

network-admin

Parameters

port-number: Specifies a UDP port number in the range of 1024 to 65535. As a best practice, specify a port number in the range of 1024 to 49151.

acl-number: Specifies an ACL by its number in the range of 3000 to 3999. The ACL must be an advanced ACL.

Usage guidelines

This command takes effect only on IPv4-based VXLAN. Only manually created VXLAN tunnel interfaces support this command.

This command enables a VXLAN tunnel interface to filter frames by using an ACL and encapsulate a specific source UDP port number for matching frames. This allows IPsec to identify the VXLAN packets to encrypt by the source UDP port number in the VXLAN encapsulation.

If the ACL specified by using this command does not exist or does not contain an IP address-related rule, frames are encapsulated based on the default setting.

This command has a higher priority than the vxlan source udp-port five-tuple command.

If you execute this command multiple times, the most recent configuration takes effect.

Examples

# Configure VXLAN tunnel interface Tunnel 1 to encapsulate source UDP port number 50001 for the frames that match ACL 3001.

<Sysname> system-view

[Sysname] interface tunnel 1 mode vxlan

[Sysname-Tunnel1] vxlan source udp-port 50001 acl 3001

Related commands

acl (ACL and QoS Command Reference)

vxlan source udp-port five-tuple

Use vxlan source udp-port five-tuple to configure a VXLAN tunnel interface to generate the source UDP port number in the VXLAN encapsulation based on the IP five-tuple of the inner Ethernet frame.

Use undo vxlan source udp-port five-tuple to restore the default.

Syntax

vxlan source udp-port five-tuple

undo vxlan source udp-port five-tuple

Default

The source UDP port number in the VXLAN encapsulation is generated based on the source and destination MAC addresses of the inner Ethernet frame.

Views

VXLAN tunnel interface view

VXLAN-DCI tunnel interface view

Predefined user roles

network-admin

Usage guidelines

This command takes effect only on IPv4-based VXLAN. Only manually created VXLAN tunnel interfaces support this command.

This command has a lower priority than the vxlan source udp-port acl command. If you use both commands on a VXLAN tunnel interface, the vxlan source udp-port five-tuple command takes effect only on the frames that fail to match the ACL specified by using the vxlan source udp-port acl command.

Examples

# Configure VXLAN tunnel interface Tunnel 1 to generate the source UDP port number in the VXLAN encapsulation based on the IP five-tuple of the inner Ethernet frame.

<Sysname> system-view

[Sysname] interface tunnel 1 mode vxlan

[Sysname-Tunnel1] vxlan source udp-port five-tuple

Related commands

vxlan source udp-port acl

vxlan tunnel mac-learning disable

Use vxlan tunnel mac-learning disable to disable remote-MAC address learning.

Use undo vxlan tunnel mac-learning disable to enable remote-MAC address learning.

Syntax

vxlan tunnel mac-learning disable

undo vxlan tunnel mac-learning disable

Default

Remote-MAC address learning is enabled.

Views

System view

Predefined user roles

network-admin

Usage guidelines

When network attacks occur, use this command to prevent the device from learning incorrect remote MAC addresses in the data plane.

Examples

# Disable remote-MAC address learning.

<Sysname> system-view

[Sysname] vxlan tunnel mac-learning disable

vxlan udp-port

Use vxlan udp-port to set the destination UDP port number for VXLAN packets.

Use undo vxlan udp-port to restore the default.

Syntax

vxlan udp-port port-number

undo vxlan udp-port

Default

The destination UDP port number is 4789 for VXLAN packets.

Views

System view

Predefined user roles

network-admin

Parameters

port-number: Specifies a UDP port number in the range of 1 to 65535. As a best practice, specify a port number in the range of 1024 to 65535 to avoid conflict with well-known ports.

Usage guidelines

You must configure the same destination UDP port number on all VTEPs in a VXLAN.

Examples

# Set the destination UDP port number to 6666 for VXLAN packets.

<Sysname> system-view

[Sysname] vxlan udp-port 6666

xconnect vsi

Use xconnect vsi to map an AC to a VSI.

Use undo xconnect vsi to restore the default.

Syntax

xconnect vsi vsi-name [ access-mode { ethernet | vlan } ] [ track track-entry-number&<1-3> ]

undo xconnect vsi

Default

An AC is not mapped to any VSI.

Views

Ethernet service instance view

Interface view

Predefined user roles

network-admin

Parameters

vsi-name: Specifies the VSI name, a case-sensitive string of 1 to 31 characters.

track track-entry-number&<1-3>: Specifies a space-separated list of up to three track entry numbers in the range of 1 to 1024. The AC is up only if a minimum of one associated track entry is in positive state.

Usage guidelines

For traffic that matches a Layer 3 interface, the system uses the VSI's MAC address table to make a forwarding decision.

The access mode determines how a VTEP processes the 802.1Q VLAN tags in the inner Ethernet frames assigned to the VSI.

· VLAN access mode—Ethernet frames received from or sent to the local site must contain 802.1Q VLAN tags.

¡ For an Ethernet frame received from the local site, the VTEP removes all its 802.1Q VLAN tags before forwarding the frame.

¡ For an Ethernet frame destined for the local site, the VTEP adds 802.1Q VLAN tags to the frame before forwarding the frame.

In VLAN access mode, VXLAN packets sent between VXLAN sites do not contain 802.1Q VLAN tags. VXLAN can provide Layer 2 connectivity for different 802.1Q VLANs between sites. You can use different 802.1Q VLANs to provide the same service in different sites.

· Ethernet access mode—The VTEP does not process the 802.1Q VLAN tags of Ethernet frames received from or sent to the local site.

¡ For an Ethernet frame received from the local site, the VTEP forwards the frame with the 802.1Q VLAN tags intact.

¡ For an Ethernet frame destined for the local site, the VTEP forwards the frame without adding 802.1Q VLAN tags.

In Ethernet access mode, VXLAN packets sent between VXLAN sites contain 802.1Q VLAN tags. VXLAN cannot provide Layer 2 connectivity for different 802.1Q VLANs between sites. You must use the same 802.1Q VLAN to provide the same service between sites.

After you modify the access mode on a Layer 3 subinterface AC, local VMs that access the VXLAN network through the subinterface cannot communicate with remote VMs. To resolve this issue, you must clear the ARP entries on the local VMs or configure them to periodically send gratuitous ARP packets.

Examples

# Map GigabitEthernet 1/0 to VSI vpn1.

<Sysname> system-view

[Sysname] vsi vpn1

[Sysname-vsi-vpn1] quit

[Sysname] interface gigabitethernet 1/0

[Sysname-GigabitEthernet1/0] xconnect vsi vpn1

Related commands

display l2vpn interface

vsi

VXLAN IP gateway commands

arp distributed-gateway dynamic-entry synchronize

Use arp distributed-gateway dynamic-entry synchronize to enable dynamic ARP entry synchronization for distributed VXLAN IP gateways.

Use undo arp distributed-gateway dynamic-entry synchronize to disable dynamic ARP entry synchronization for distributed VXLAN IP gateways.

Syntax

arp distributed-gateway dynamic-entry synchronize

undo arp distributed-gateway dynamic-entry synchronize

Default

Dynamic ARP entry synchronization is disabled for distributed VXLAN IP gateways.

Views

System view

Predefined user roles

network-admin

Usage guidelines

When local proxy ARP is enabled on distributed VXLAN IP gateways, each gateway learns ARP information independently. A gateway does not forward ARP packets destined for its local VSI interfaces to other gateways. For distributed VXLAN IP gateways to have the same ARP entries, you must enable dynamic ARP entry synchronization.

A controller or the EVPN feature can also synchronize ARP entries among distributed VXLAN IP gateways. When you use a controller or the EVPN feature, do not enable dynamic ARP entry synchronization.

Examples

# Enable dynamic ARP entry synchronization for distributed VXLAN IP gateways.

<Sysname> system-view

[Sysname] arp distributed-gateway dynamic-entry synchronize

Related commands

distributed-gateway local

local-proxy-arp enable (Layer 3—IP Services Command Reference)

bandwidth

Use bandwidth to set the expected bandwidth for a VSI interface or VSI subinterface.

Use undo bandwidth to restore the default.

Syntax

bandwidth bandwidth-value

undo bandwidth

Default

The expected bandwidth (in kbps) equals the interface baudrate divided by 1000.

Views

VSI interface view

VSI subinterface view

Predefined user roles

network-admin

Parameters

bandwidth-value: Specifies the expected bandwidth, in the range of 1 to 400000000 kbps.

Usage guidelines

The expected bandwidth is an informational parameter used only by higher-layer protocols for calculation. You cannot adjust the actual bandwidth of an interface by using this command.

Examples

# Set the expected bandwidth to 10000 kbps for VSI-interface 100.

<Sysname> system-view

[Sysname] interface vsi-interface 100

[Sysname-Vsi-interface100] bandwidth 10000

default

Use default to restore the default settings for a VSI interface or VSI subinterface.

Syntax

default

Views

VSI interface view

VSI subinterface view

Predefined user roles

network-admin

Usage guidelines

CAUTION:

The default command might interrupt ongoing network services. Make sure you are fully aware of the impact of this command when you use it on a live network.

This command might fail to restore the default settings for some commands for reasons such as command dependencies and system restrictions.

To resolve this problem:

1. Use the display this command in interface view to identify these commands.

2. Use their undo forms or follow the command reference to restore their default settings.

3. If the restoration attempt still fails, follow the error message instructions to resolve the problem.

Examples

# Restore the default settings for VSI-interface 100.

<Sysname> system-view

[Sysname] interface vsi-interface 100

[Sysname-Vsi-interface100] default

This command will restore the default settings. Continue? [Y/N]:y

description

Use description to configure the description of a VSI interface or VSI subinterface.

Use undo description to restore the default.

Syntax

description text

undo description

Default

The description of a VSI interface or VSI subinterface is interface-name plus Interface (for example, Vsi-interface100 Interface).

Views

VSI interface view

VSI subinterface view

Predefined user roles

network-admin

Parameters

text: Specifies a description, a case-sensitive string of 1 to 255 characters.

Examples

# Configure the description as gateway for VXLAN 10 for VSI-interface 100.

<Sysname> system-view

[Sysname] interface vsi-interface 100

[Sysname-Vsi-interface100] description gateway for VXLAN 10

display interface vsi-interface

Use display interface vsi-interface to display information about VSI interfaces or VSI subinterfaces.

Syntax

display interface [ vsi-interface [ vsi-interface-id | vsi-interface-id.subid ] ] [ brief [ description | down ] ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

vsi-interface [ vsi-interface-id | vsi-interface-id.subid ]: Specifies a VSI interface or VSI subinterface by its number. Make sure the specified VSI interface or VSI subinterface has been created on the device. If you do not specify the vsi-interface [ vsi-interface-id | vsi-interface-id.subid ] option, this command displays information about all interfaces except for VA interfaces. If you specify only the vsi-interface keyword, this command displays information about all VSI interfaces and VSI subinterfaces. If you specify a VSI interface or VSI subinterface, this command displays information about the specified interface or subinterface. For more information about VA interfaces, see PPPoE configuration in Layer 2—WAN Access Configuration Guide.

brief: Display brief interface information. If you do not specify this keyword, the command displays detailed interface information.

description: Displays complete interface descriptions. If you do not specify this keyword, the command displays only the first 27 characters of interface descriptions.

down: Displays interfaces that are physically down as well as the down reason. If you do not specify this keyword, the command does not filter output by physical interface state.

Examples

# Display information about VSI-interface 100.

<Sysname> display interface vsi-interface 100

Vsi-interface100

Current state: UP

Line protocol state: UP

Description: Vsi-interface100 Interface

Bandwidth: 1000000 kbps

Maximum transmission unit: 1500

Internet address: 10.1.1.1/24 (primary)

IP packet frame type: Ethernet II, hardware address: 0011-2200-0102

IPv6 packet frame type: Ethernet II, hardware address: 0011-2200-0102

Physical: Unknown, baudrate: 1000000 kbps

Last clearing of counters: Never

Last 300 seconds input rate: 0 bytes/sec, 0 bits/sec, 0 packets/sec

Last 300 seconds output rate: 0 bytes/sec, 0 bits/sec, 0 packets/sec

Input: 0 packets, 0 bytes, 0 drops

Output: 0 packets, 0 bytes, 0 drops

Table 8 Command output

Field	Description
Current state	Physical link state of the interface: · Administratively DOWN—The interface has been shut down by using the shutdown command. · DOWN—The interface is administratively up, but its physical state is down. · UP—The interface is both administratively and physically up.
Line protocol state	Data link layer state of the interface: · UP—The data link layer protocol is up. · UP(spoofing)—The data link layer protocol is up, but the link is an on-demand link or does not exist. · DOWN—The data link layer protocol is down.
Description	Description of the interface.
Bandwidth	Expected bandwidth of the interface.
Maximum transmission unit	MTU of the interface.
Internet protocol processing: Disabled	The interface is not assigned an IP address and cannot process IP packets.
Internet address: ip-address/mask-length (Type)	IP address of the interface and type of the address in parentheses. Possible IP address types include: · Primary—Manually configured primary IP address. · Sub—Manually configured secondary IP address. If the interface has both primary and secondary IP addresses, the primary IP address is displayed. If the interface has only secondary IP addresses, the lowest secondary IP address is displayed. · DHCP-Allocated—DHCP allocated IP address. For more information, see DHCP client configuration in Layer 3—IP Services Configuration Guide. · BOOTP-Allocated—BOOTP allocated IP address. For more information, see BOOTP client configuration in Layer 3—IP Services Configuration Guide. · PPP-Negotiated—IP address assigned by a PPP server during PPP negotiation. For more information, see PPP configuration in Layer 2—WAN Access Configuration Guide. · Unnumbered—IP address borrowed from another interface. · MAD—IP address assigned to an IRF member device for MAD on the interface. For more information, see IRF configuration in Virtual Technologies Configuration Guide. · MTunnel—IP address of the multicast tunnel interface (MTI), which is the same as the IP address of the MVPN source interface. For more information, see multicast VPN configuration in IP Multicast Configuration Guide.
IP packet frame type	IPv4 packet framing format.
hardware address	MAC address.
IPv6 packet frame type	‌ IPv6 packet framing format.
Physical	Physical type of the interface, which is fixed at Unknown.
baudrate	Interface baudrate in kbps.
Last clearing of counters	Last time when the reset counters interface vsi-interface command was used to clear interface statistics. This field displays Never if the reset counters interface vsi-interface command has never been used on the interface since the device startup.
Last 300 seconds input rate	Average input rate for the last 300 seconds.
Last 300 seconds output rate	Average output rate for the last 300 seconds.
Input: 0 packets, 0 bytes, 0 drops	Incoming traffic statistics on the interface: · Number of incoming packets. · Number of incoming bytes. · Number of dropped incoming packets.
Output: 0 packets, 0 bytes, 0 drops	Outgoing traffic statistics on the interface: · Number of outgoing packets. · Number of outgoing bytes. · Number of dropped outgoing packets.

# Display brief information about all VSI interfaces.

<Sysname> display interface vsi-interface brief

Brief information on interfaces in route mode:

Link: ADM - administratively down; Stby - standby

Protocol: (s) - spoofing

Interface Link Protocol Primary IP Description

Vsi100 DOWN DOWN --

# Display brief information and complete description for VSI-interface 100.

<Sysname> display interface vsi-interface 100 brief description

Brief information on interfaces in route mode:

Link: ADM - administratively down; Stby - standby

Protocol: (s) - spoofing

Interface Link Protocol Primary IP Description

Vsi100 UP UP 1.1.1.1 VSI-interface100

# Displays interfaces that are physically down and the down reason.

<Sysname> display interface brief down

Brief information on interfaces in route mode:

Link: ADM - administratively down; Stby - standby

Interface Link Cause

Vsi100 DOWN Administratively

Vsi200 DOWN Administratively

Table 9 Command output

Field	Description
Interface	Abbreviated interface name.
Link	Physical link state of the interface: · UP—The interface is physically up. · DOWN—The interface is physically down. · ADM—The interface has been shut down by using the shutdown command. To restore the physical state of the interface, use the undo shutdown command. · Stby—The interface is a backup interface in standby state. To see the primary interface, use the display interface-backup state command.
Protocol	Data link layer protocol state of the interface: · UP—The data link layer protocol of the interface is up. · UP (s)—The data link layer protocol of the interface is up, but the link is an on-demand link or does not exist. The (s) attribute represents the spoofing flag. · DOWN—The data link layer protocol of the interface is down.
Primary IP	Primary IP address of the interface. This field displays two hyphens (--) if the interface does not have an IP address.
Description	Description of the interface.
Cause	Cause for the physical link state of an interface to be DOWN: · Administratively—The interface has been manually shut down by using the shutdown command. To restore the physical state of the interface, use the undo shutdown command. · Not connected—The interface is not mapped to any VSI, or the mapped VSI does not have any AC or VXLAN tunnel.

Related commands

reset counters interface vsi-interface

distributed-gateway local

Use distributed-gateway local to specify a VSI interface as a distributed gateway to provide services for the local site.

Use undo distributed-gateway local to restore the default.

Syntax

distributed-gateway local

undo distributed-gateway local

Default

A VSI interface is not a distributed gateway.

Views

VSI interface view

Predefined user roles

network-admin

Usage guidelines

If a VXLAN uses distributed gateway services, you must assign the same IP address to the VXLAN's VSI interfaces on different VTEPs. To avoid IP address conflicts, you must specify the VSI interface on each VTEP as a distributed gateway.

Examples

# Specify VSI-interface 100 as a distributed gateway.

<Sysname> system-view

[Sysname] interface vsi-interface 100

[Sysname-Vsi-interface100] distributed-gateway local

gateway subnet

Use gateway subnet to assign a subnet to a VSI.

Use undo gateway subnet to remove a subnet from a VSI.

Syntax

gateway subnet { ipv4-address wildcard-mask | ipv6-address prefix-length }

undo gateway subnet { ipv4-address wildcard-mask | ipv6-address prefix-length }

Default

No subnet is assigned to a VSI.

Views

VSI view

Predefined user roles

network-admin

Parameters

ipv4-address: Specifies an IPv4 subnet address in dotted-decimal notation.

wildcard-mask: Specifies a wildcard mask in dotted decimal notation. In contrast to a network mask, the 0 bits in a wildcard mask represent "do care" bits, and the 1 bits represent "don't care" bits. If the "do care" bits in a packet's IP address are identical to the "do care" bits in the specified subnet address, the packet is assigned to the VSI. All "don't care" bits are ignored. The 0s and 1s in a wildcard mask can be noncontiguous. For example, 0.255.0.255 is a valid wildcard mask.

ipv6-address prefix-length: Specifies an IPv6 subnet address and the address prefix length in the range of 1 to 128.

Usage guidelines

You must configure this command on VSIs that share a gateway interface. This command enables the VSI interface to identify the VSI of a packet.

You can assign a maximum of eight IPv4 and IPv6 subnets to a VSI.

You must specify a gateway interface for a VSI before you can assign subnets to the VSI. If you remove the gateway interface from the VSI, the VSI's subnet settings are automatically deleted.

For VSIs that share a gateway interface, the subnets must be unique.

Examples

# Assign subnet 100.0.10.0/24 to VSI vxlan.

<Sysname> system-view

[Sysname] vsi vxlan

[Sysname-vsi-vxlan] gateway subnet 100.0.10.0 0.0.0.255

gateway vsi-interface

Use gateway vsi-interface to specify a gateway interface for a VSI.

Use undo gateway vsi-interface to restore the default.

Syntax

gateway vsi-interface vsi-interface-id

undo gateway vsi-interface

Default

No gateway interface is specified for a VSI.

Views

VSI view

Predefined user roles

network-admin

Parameters

vsi-interface-id: Specifies a VSI interface by its number. The value range for this argument is 0 to 8191.

Usage guidelines

A VSI can have only one gateway interface. Multiple VSIs can share a gateway interface.

Examples

# Specify VSI-interface 100 as the gateway interface for VSI vpna.

<Sysname> system-view

[Sysname] vsi vpna

[Sysname-vsi-vpna] gateway vsi-interface 100

Related commands

interface vsi-interface

Use interface vsi-interface to create a VSI interface or VSI subinterface and enter its view, or enter the view of an existing VSI interface or VSI subinterface.

Use undo interface vsi-interface to delete a VSI interface or VSI subinterface.

Syntax

interface vsi-interface { vsi-interface-id | vsi-interface-id.subid }

undo interface vsi-interface { vsi-interface-id | vsi-interface-id.subid }

Default

No VSI interfaces or VSI subinterfaces exist.

Views

System view

Predefined user roles

network-admin

Parameters

vsi-interface-id: Specifies a VSI interface number. The value range for this argument is 0 to 8191.

vsi-interface-id.subid: Specifies a VSI subinterface by its number. The value range for this argument is 1 to 8192.

Usage guidelines

Before you create a VSI subinterface, make sure its main VSI interface has been created.

The number of VSI subinterfaces that you can create varies by device model.

Examples

# Create VSI-interface 100 and enter VSI interface view.

<Sysname> system-view

[Sysname] interface vsi-interface 100

[Sysname-Vsi-interface100]

Related commands

gateway vsi-interface

mac-address

Use mac-address to assign a MAC address to a VSI interface or VSI subinterface.

Use undo mac-address to restore the default.

Syntax

mac-address mac-address

undo mac-address

Default

The MAC address of a VSI interface is the bridge MAC address.

Views

VSI interface view

VSI subinterface view

Predefined user roles

network-admin

Parameters

mac-address: Specifies a MAC address in H-H-H format.

Examples

# Assign MAC address 0001-0001-0001 to VSI-interface 100.

<Sysname> system-view

[Sysname] interface vsi-interface 100

[Sysname-Vsi-interface100] mac-address 1-1-1

mtu

Use mtu to set the MTU for a VSI interface or VSI subinterface.

Use undo mtu to restore the default.

Syntax

mtu size

undo mtu

Default

The MTU is 1500 bytes.

Views

VSI interface view

VSI subinterface view

Predefined user roles

network-admin

Parameters

size: Specifies an MTU value in the range of 46 to 9216 bytes.

Examples

# Set the MTU to 1430 bytes for VSI-interface 100.

<Sysname> system-view

[Sysname] interface vsi-interface 100

[Sysname-Vsi-interface100] mtu 1430

reset counters interface vsi-interface

Use reset counters interface vsi-interface to clear packet statistics on VSI interfaces or VSI subinterfaces.

Syntax

reset counters interface [ vsi-interface [ vsi-interface-id | vsi-interface-id.subid ] ]

Views

User view

Predefined user roles

network-admin

Parameters

vsi-interface [ vsi-interface-id | vsi-interface-id.subid ]: Specifies a VSI interface or VSI subinterface by its number. Make sure the specified VSI interface or VSI subinterface has been created on the device. If you do not specify the vsi-interface [ vsi-interface-id | vsi-interface-id.subid ] option, this command clears packet statistics on all interfaces except for VA interfaces. If you specify only the vsi-interface keyword, this command clears packet statistics on all VSI interfaces and VSI subinterfaces. If you specify a VSI interface or subinterface, this command clears packet statistics on the specified interface or subinterface.

Usage guidelines

Use this command to clear history statistics before you collect traffic statistics for a time period.

Examples

# Clear packet statistics on VSI-interface 100.

<Sysname> reset counters interface vsi-interface 100

Related commands

display interface vsi-interface

shutdown

Use shutdown to shut down a VSI interface or VSI subinterface.

Use undo shutdown to bring up a VSI interface or VSI subinterface.

Syntax

shutdown

undo shutdown

Default

A VSI interface or subinterface is not manually shut down.

Views

VSI interface view

VSI subinterface view

Predefined user roles

network-admin

Examples

# Shut down VSI-interface 100.

<Sysname> system-view

[Sysname] interface vsi-interface 100

[Sysname-Vsi-interface100] shutdown

vtep group member local

Use vtep group member local to assign the local VTEP to a VTEP group.

Use undo vtep group member local to remove the local VTEP from a VTEP group.

Syntax

vtep group group-ip member local member-ip

undo vtep group group-ip member local

Default

A VTEP is not assigned to any VTEP group.

Views

System view

Predefined user roles

network-admin

Parameters

group-ip: Specifies a VTEP group by its group IP address. The IP address must already exist on the local VTEP.

member-ip: Specifies the member VTEP IP address for the local VTEP. The IP address must already exist on the local VTEP.

Usage guidelines

Member VTEPs in a VTEP group cannot use the group IP address or share an IP address.

Examples

# Assign the local VTEP to VTEP group 1.1.1.1, and specify 2.2.2.2 as the member VTEP IP address of the local VTEP.

<Sysname> system-view

[Sysname] vtep group 1.1.1.1 member local 2.2.2.2

Related commands

vtep group member remote

Use vtep group member remote to specify a VTEP group and its member VTEPs.

Use undo vtep group member remote to remove a VTEP group and its member VTEPs.

Syntax

vtep group group-ip member remote member-ip&<1-8>

undo vtep group group-ip member remote

Default

No VTEP group is specified.

Views

System view

Predefined user roles

network-admin

Parameters

group-ip: Specifies a VTEP group by its group IP address.

member-ip&<1-8>: Specifies a space-separated list of up to eight member VTEP IP addresses.

Examples

# Specify VTEP group 1.1.1.1 and its member VTEPs at 2.2.2.2, 3.3.3.3, and 4.4.4.4.

<Sysname> system-view

[Sysname] vtep group 1.1.1.1 member remote 2.2.2.2 3.3.3.3 4.4.4.4

Related commands

vtep group member local

vxlan tunnel arp-learning disable

Use vxlan tunnel arp-learning disable to disable remote ARP learning for VXLANs.

Use undo vxlan tunnel arp-learning disable to enable remote ARP learning for VXLANs.

Syntax

vxlan tunnel arp-learning disable

undo vxlan tunnel arp-learning disable

Default

Remote ARP learning is enabled for VXLANs.

Views

System view

Predefined user roles

network-admin

Usage guidelines

By default, the device learns ARP information of remote VMs from packets received on VXLAN tunnel interfaces. To save resources on VTEPs in an SDN transport network, you can temporarily disable remote ARP learning when the controller and VTEPs are synchronizing entries. After the entry synchronization is completed, use the undo vxlan tunnel arp-learning disable command to enable remote ARP learning.

As a best practice, disable remote ARP learning for VXLANs only when the controller and VTEPs are synchronizing entries.

Examples

# Disable remote ARP learning for VXLANs.

<Sysname> system

[Sysname] vxlan tunnel arp-learning disable

OVSDB commands

ovsdb server bootstrap ca-certificate

Use ovsdb server bootstrap ca-certificate to specify a CA certificate file for establishing OVSDB SSL connections.

Use undo ovsdb server bootstrap ca-certificate to restore the default.

Syntax

ovsdb server bootstrap ca-certificate ca-filename

undo ovsdb server bootstrap ca-certificate

Default

SSL uses the CA certificate file in the PKI domain.

Views

System view

Predefined user roles

network-admin

Parameters

ca-filename: Specifies the CA certificate file name, a case-insensitive string. The file name cannot contain the slot string, and the file must be stored on the active MPU.

Usage guidelines

For the specified certificate to take effect, you must execute the ovsdb server enable command to enable the OVSDB server. You must disable and then re-enable the OVSDB server if it has been enabled.

If the specified CA certificate file does not exist, the device obtains a self-signed certificate from the controller. The obtained file uses the name specified for the ca-filename argument.

Examples

# Specify CA certificate file ca-new for establishing OVSDB SSL connections.

<Sysname> system-view

[Sysname] ovsdb server bootstrap ca-certificate ca-new

Related commands

ovsdb server enable

ovsdb server pki domain

ovsdb server pssl

ovsdb server ssl

ovsdb server enable

Use ovsdb server enable to enable the OVSDB server.

Use undo ovsdb server enable to disable the OVSDB server.

Syntax

ovsdb server enable

undo ovsdb server enable

Default

The OVSDB server is disabled.

Views

System view

Predefined user roles

network-admin

Usage guidelines

To obtain configuration data from controllers, you must enable the OVSDB server.

Before you enable the OVSDB server, you must establish an OVSDB SSL or TCP connection with a minimum of one controller.

Examples

# Enable the OVSDB server.

<Sysname> system-view

[Sysname] ovsdb server enable

ovsdb server pki domain

Use ovsdb server pki domain to specify a PKI domain for establishing OVSDB SSL connections.

Use undo ovsdb bootstrap server pki domain to restore the default.

Syntax

ovsdb server pki domain domain-name

undo ovsdb server pki domain

Default

No PKI domain is specified for establishing OVSDB SSL connections.

Views

System view

Predefined user roles

network-admin

Parameters

domain-name: Specifies a PKI domain name, a case-sensitive string of 1 to 31 characters. The PKI domain must already exist and contain a complete certificate and key.

Usage guidelines

To communicate with controllers through SSL, you must specify a PKI domain.

For the specified PKI domain to take effect, you must execute the ovsdb server enable command to enable the OVSDB server. You must disable and then re-enable the OVSDB server if it has been enabled.

For more information about PKI domains, see PKI in Security Configuration Guide.

Examples

# Specify PKI domain ovsdb_test for establishing OVSDB SSL connections.

<Sysname> system-view

[Sysname] ovsdb server pki domain ovsdb_test

Related commands

ovsdb server bootstrap ca-certificate

ovsdb server enable

ovsdb server pssl

ovsdb server ssl

ovsdb server pssl

Use ovsdb server pssl to enable the device to listen for OVSDB SSL connection requests.

Use undo ovsdb server pssl to restore the default.

Syntax

ovsdb server pssl [ port port-number ]

undo ovsdb server pssl

Default

The device does not listen for OVSDB SSL connection requests.

Views

System view

Predefined user roles

network-admin

Parameters

port port-number: Specifies a port to listen for OVSDB SSL connection requests. The value range for the port-number argument is 1 to 65535. If you do not specify a port, the device uses the port number 6640.

Usage guidelines

Before you use this command, you must specify a PKI domain for SSL.

You can specify only one port to listen for OVSDB SSL connection requests. If you execute this command multiple times, the most recent configuration takes effect.

For the specified port setting to take effect, you must execute the ovsdb server enable command to enable the OVSDB server. You must disable and then re-enable the OVSDB server if it has been enabled.

Examples

# Enable the device to listen for OVSDB SSL connection requests on port 6640.

<Sysname> system-view

[Sysname] ovsdb server pssl

Related commands

ovsdb server bootstrap ca-certificate

ovsdb server enable

ovsdb server pki domain

ovsdb server ssl

ovsdb server ptcp

Use ovsdb server ptcp to enable the device to listen for OVSDB TCP connection requests.

Use undo ovsdb server ptcp to restore the default.

Syntax

ovsdb server ptcp [ port port-number ]

undo ovsdb server ptcp

Default

The device does not listen for OVSDB TCP connection requests.

Views

System view

Predefined user roles

network-admin

Parameters

port-number: Specifies a port to listen for OVSDB TCP connection requests. The value range for the port-number argument is 1 to 65535. If you do not specify a port, the device uses the port number 6640.

Usage guidelines

You can specify only one port to listen for OVSDB TCP connection requests. If you execute this command multiple times, the most recent configuration takes effect.

Examples

# Enable the device to listen for OVSDB TCP connection requests on port 6640.

<Sysname> system-view

[Sysname] ovsdb server ptcp

Related commands

ovsdb server enable

ovsdb server tcp

ovsdb server ssl

Use ovsdb server ssl to set up an active OVSDB SSL connection to a controller.

Use undo ovsdb server ssl to remove an OVSDB SSL connection from a controller.

Syntax

ovsdb server ssl ip ip-address port port-number

undo ovsdb server ssl ip ip-address port port-number

Default

The device does not have active OVSDB SSL connections to a controller.

Views

System view

Predefined user roles

network-admin

Parameters

ip ip-address: Specifies the destination IP address for the SSL connection.

port port-number: Specifies the destination port for the SSL connection. The value range for the port-number argument is 1 to 65535.

Usage guidelines

Before you use this command, you must specify a PKI domain for SSL.

The device can have a maximum of eight active SSL connections.

To establish the connection, you must execute the ovsdb server enable command. You must disable and then re-enable the OVSDB server if it has been enabled.

Examples

# Set up an active SSL connection to port 6632 at 192.168.12.2.

<Sysname> system-view

[Sysname] ovsdb server ssl ip 192.168.12.2 port 6632

Related commands

ovsdb server bootstrap ca-certificate

ovsdb server enable

ovsdb server pki domain

ovsdb server pssl

ovsdb server tcp

Use ovsdb server tcp to set up an active OVSDB TCP connection to a controller.

Use undo ovsdb server tcp to remove an OVSDB TCP connection.

Syntax

ovsdb server tcp ip ip-address port port-number

undo ovsdb server tcp ip ip-address port port-number

Default

The device does not have active OVSDB TCP connections.

Views

System view

Predefined user roles

network-admin

Parameters

ip ip-address: Specifies the destination IP address for the TCP connection.

port port-number: Specifies the destination port for the TCP connection. The value range for the port-number argument is 1 to 65535.

Usage guidelines

The device can have a maximum of eight active OVSDB TCP connections.

To establish the connection, you must execute the ovsdb server enable command. You must disable and then re-enable the OVSDB server if it has been enabled.

Examples

# Set up an active OVSDB TCP connection to port 6632 at 192.168.12.2.

<Sysname> system-view

[Sysname] ovsdb server tcp ip 192.168.12.2 port 6632

Related commands

ovsdb server enable

ovsdb server ptcp

vtep access port

Use vtep access port to specify a site-facing interface as a VTEP access port.

Use undo vtep access port to restore the default.

Syntax

vtep access port

undo vtep access port

Default

An interface is not a VTEP access port.

Views

Layer 2 aggregate interface view

Layer 2 Ethernet interface view

Layer 3 interface view

Predefined user roles

network-admin

Usage guidelines

For controllers to manage a site-facing interface, you must specify the interface as a VTEP access port.

Examples

# Specify GigabitEthernet 1/0 as a VTEP access port.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0

[Sysname-GigabitEthernet1/0] vtep access port

vtep enable

Use vtep enable to enable the OVSDB VTEP service.

Use undo vtep enable to disable the OVSDB VTEP service.

Syntax

vtep enable

undo vtep enable

Default

The OVSDB VTEP service is disabled.

Views

System view

Predefined user roles

network-admin

Examples

# Enable the OVSDB VTEP service.

<Sysname> system-view

[Sysname] vtep enable

vxlan tunnel flooding-proxy

Use vxlan tunnel flooding-proxy to enable flood proxy on multicast VXLAN tunnels.

Use undo vxlan tunnel flooding-proxy to disable flood proxy on multicast VXLAN tunnels.

Syntax

vxlan tunnel flooding-proxy

undo vxlan tunnel flooding-proxy

Default

Flood proxy is disabled on multicast VXLAN tunnels.

Views

System view

Predefined user roles

network-admin

Usage guidelines

If you use a flood proxy server, you must enable flood proxy globally on multicast tunnels. Then the multicast tunnels are converted into flood proxy tunnels. The VTEP sends broadcast, multicast, and unknown unicast traffic for a VXLAN to the flood proxy server through the tunnels. The flood proxy server then replicates and forwards flood traffic to remote VTEPs.

The vxlan tunnel flooding-proxy command and its undo form affect only VXLAN tunnels that are issued after the vxlan tunnel flooding-proxy command.

Examples

# Enable flood proxy on all multicast VXLAN tunnels.

<Sysname> system

[Sysname] vxlan tunnel flooding-proxy

15-VXLAN Command Reference

VXLAN commands

arp suppression enable

display arp suppression vsi

flooding disable

mac-address static vsi

tunnel

vxlan

vxlan local-mac report

vxlan source udp-port acl

display interface vsi-interface

reset counters interface vsi-interface

Cloud & AI

InterConnect

Intelligent Terminal Products

Product Support Services

Technical Service Solutions

Resource Center

Policy

Online Help

Become a Partner

Partner Resources

Partner Business Management

Company Information

News & Events

Contact Us