Configuration made in BGP EVPN address family view takes effect only on routes and peers of the BGP EVPN address family that are on the public network.

Examples

# Create the BGP EVPN address family and enter its view.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp-default] address-family l2vpn evpn

[Sysname-bgp-default-evpn]

advertise evpn route

Use advertise evpn route to enable BGP EVPN route advertisement for the BGP VPNv4 or VPNv6 address family.

Use undo advertise evpn route to disable BGP EVPN route advertisement for the BGP VPNv4 or VPNv6 address family.

Syntax

advertise evpn route [ replace-rt ][ advertise-policy policy-name ]

undo advertise evpn route

Default

BGP EVPN routes are not advertised through the BGP VPNv4 or VPNv6 address family.

Views

BGP VPNv4 address family

BGP VPNv6 address family

Predefined user roles

network-admin

Parameters

replace-rt: Replaces the route targets of BGP EVPN routes with the route targets of BGP VPNv4 or VPNv6 routes. If you do not specify this keyword, route targets of BGP EVPN routes are not modified.

advertise-policy policy-name: Specifies a routing policy to filter the BGP EVPN routes to be advertised to BGP VPNv4 or VPNv6 peers. The policy-name argument specifies the routing policy name, a case-sensitive string of 1 to 63 characters. If you do not specify this option, all BGP EVPN routes are advertised to BGP VPNv4 or VPNv6 peers.

Usage guidelines

To enable communication between data centers interconnected through an MPLS L3VPN network, you must configure the BGP EVPN address family and the BGP VPNv4 or VPNv6 address family to exchange routes on EDs.

After you execute this command, the device advertises IP prefix advertisement routes and MAC/IP advertisement routes that contain host route information through the BGP VPNv4 or VPNv6 address family.

Examples

# Enable BGP EVPN route advertisement for the BGP VPNv4 address family.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp-default] address-family vpnv4

[Sysname-bgp-default-vpnv4] advertise evpn route

advertise l2vpn evpn

Use advertise l2vpn evpn to enable BGP EVPN route advertisement to the local site.

Use undo advertise l2vpn evpn to disable BGP EVPN route advertisement to the local site.

Syntax

advertise l2vpn evpn

undo advertise l2vpn evpn

Default

BGP EVPN route advertisement to the local site is enabled.

Views

BGP-VPN IPv4 unicast address family view

BGP-VPN IPv6 unicast address family view

Predefined user roles

network-admin

Usage guidelines

This command enables the device to advertise BGP EVPN routes to the local site after the device adds the routes to the routing table of a VPN instance. The BGP EVPN routes here are IP prefix advertisement routes and MAC/IP advertisement routes that contain ARP or ND information.

Examples

# Enable BGP EVPN route advertisement to the local site for VPN instance vpn1.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp-default] ip vpn-instance vpn1

[Sysname-bgp-default-vpn1] address-family ipv4

[Sysname-bgp-default-ipv4-vpn1] advertise l2vpn evpn

advertise l3vpn route

Use advertise l3vpn route to enable BGP VPNv4 or VPNv6 route advertisement for the BGP EVPN address family.

Use undo advertise l3vpn route to disable BGP VPNv4 or VPNv6 route advertisement for the BGP EVPN address family.

Syntax

advertise l3vpn route [ replace-rt ][ advertise-policy policy-name ]

undo advertise l3vpn route

Default

BGP VPNv4 or VPNv6 routes are not advertised through the BGP EVPN address family.

Views

BGP EVPN address family view

Predefined user roles

network-admin

Parameters

replace-rt: Replaces the route targets of BGP VPNv4 or VPNv6 routes with the route targets of BGP EVPN routes. If you do not specify this keyword, route targets of BGP VPNv4 or VPNv6 routes are not modified.

advertise-policy policy-name: Specifies a routing policy to filter the BGP VPNv4 or VPNv6 routes to be advertised to BGP EVPN peers. The policy-name argument specifies the routing policy name, a case-sensitive string of 1 to 63 characters. If you do not specify this option, all BGP VPNv4 or VPNv6 routes are advertised to BGP EVPN peers.

Usage guidelines

After you execute this command, the device advertises BGP VPNv4 or VPNv6 routes as IP prefix advertisement routes through the BGP EVPN address family.

Examples

# Enable BGP VPNv4 or VPNv6 route advertisement for the BGP EVPN address family.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp-default] address-family l2vpn evpn

[Sysname-bgp-default-evpn] advertise l3vpn route

arp mac-learning disable

Use arp mac-learning disable to disable an EVPN instance from learning MAC addresses from ARP information.

Use undo arp mac-learning disable to restore the default.

Syntax

arp mac-learning disable

undo arp mac-learning disable

Default

An EVPN instance learns MAC addresses from ARP information.

Views

EVPN instance view

Predefined user roles

network-admin

Usage guidelines

The MAC information and ARP information advertised by a remote VTEP overlap. To avoid duplication, use this command to disable the learning of MAC addresses from ARP information. EVPN will learn remote MAC addresses only from the MAC information advertised from remote sites.

Examples

# Disable an EVPN instance from learning MAC addresses from ARP information.

<Sysname> system-view

[Sysname] vsi aaa

[Sysname-vsi-aaa] evpn encapsulation vxlan

[Sysname-vsi-aaa-evpn-vxlan] arp mac-learning disable

arp-advertising disable

Use arp-advertising disable to disable ARP information advertisement for an EVPN instance.

Use undo arp-advertising disable to restore the default.

Syntax

arp-advertising disable

undo arp-advertising disable

Default

ARP information advertisement is enabled for an EVPN instance.

Views

EVPN instance view

Predefined user roles

network-admin

Usage guidelines

In an EVPN network with distributed gateways, you can disable ARP information advertisement for a VXLAN to save resources if all its user terminals use the same EVPN gateway device. The EVPN instance of the VXLAN will stop advertising ARP information through MAC/IP advertisement routes and withdraw advertised ARP information. When ARP information advertisement is disabled, user terminals in other VXLANs still can communicate with that VXLAN through IP prefix advertisement routes.

Examples

# Disable ARP information advertisement for an EVPN instance.

<Sysname> system-view

[Sysname] vsi aaa

[Sysname-vsi-aaa] evpn encapsulation vxlan

[Sysname-vsi-aaa-evpn-vxlan] arp-advertising disable

dci enable

Use dci enable to enable DCI on an interface.

Use undo dci enable to disable DCI on an interface.

Syntax

dci enable

undo dci enable

Default

DCI is disabled on an interface.

Views

Interface view

Predefined user roles

network-admin

Usage guidelines

For EDs to automatically establish VXLAN-DCI tunnels, you must enable DCI on the Layer 3 interfaces that interconnect the EDs.

Subinterfaces of a DCI-enabled interface inherit configuration of the interface.

Examples

# Enable DCI on VLAN-interface 10.

<Sysname> system-view

[Sysname] interface vlan-interface 10

[Sysname-Vlan-interface10] dci enable

display bgp l2vpn evpn

Use display bgp l2vpn evpn to display BGP EVPN routes.

Syntax

display bgp [ instance instance-name ] l2vpn evpn [ peer ipv4-address { advertised-routes | received-routes } [ statistics ] | [ route-distinguisher route-distinguisher | route-type { auto-discovery | es | igmp-ls | igmp-js | imet | ip-prefix | mac-ip | smet } ] * [ { evpn-route route-length | evpn-prefix } [ advertise-info ] | ipv4-address | ipv6-address | mac-address ] | statistics ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

instance instance-name: Specifies a BGP instance by its name, a case-sensitive string of 1 to 31 characters. If you do not specify this option, the command displays BGP EVPN routes for the default BGP instance.

peer ipv4-address: Specifies a peer by its IPv4 address.

advertised-routes: Specifies the routes advertised to the specified peer.

received-routes: Specifies the routes received from the specified peer.

statistics: Displays BGP EVPN route statistics.

route-distinguisher route-distinguisher: Specifies a route distinguisher (RD), a string of 3 to 21 characters. The RD can use one of the following formats:

· 16-bit AS number:32-bit user-defined number. For example, 101:3.

· 32-bit IP address:16-bit user-defined number. For example, 192.168.122.15:1.

· 32-bit AS number:16-bit user-defined number. For example, 65536:1. The AS number must be equal to or greater than 65536.

route-type: Specifies a route type.

auto-discovery: Specifies Ethernet auto-discovery routes.

es: Specifies Ethernet segment (ES) routes.

igmp-ls: Specifies IGMP leave synch routes.

igmp-js: Specifies IGMP join synch routes.

imet: Specifies inclusive multicast Ethernet tag (IMET) routes.

ip-prefix: Specifies IP prefix advertisement routes.

mac-ip: Specifies MAC/IP advertisement routes.

smet: Specifies selective multicast Ethernet tag (SMET) routes.

evpn-route: Specifies a BGP EVPN route, a case-insensitive string of 1 to 512 characters.

route-length: Specifies the route length in bits, in the range of 0 to 65535.

evpn-prefix: Specifies a BGP EVPN route in the format of evpn-route/route-length, a case-insensitive string of 1 to 512 characters.

advertise-info: Displays advertisement information for BGP EVPN routes.

ipv4-address: Specifies an IPv4 address.

ipv6-address: Specifies an IPv6 address.

mac-address: Specifies a MAC address in MAC/IP advertisement routes. If you specify the route-type keyword, to use this argument, you must also specify the mac-ip keyword.

Usage guidelines

If you do not specify any parameter, this command displays brief information about all BGP EVPN routes.

Examples

# Display brief information about all BGP EVPN routes.

<Sysname> display bgp l2vpn evpn

BGP local router ID is 8.8.8.8

Status codes: * - valid, > - best, d - dampened, h - history,

s - suppressed, S - stale, i - internal, e - external

a - additional-path

Origin: i - IGP, e - EGP, ? - incomplete

Total number of routes from all PEs: 3

Route distinguisher: 1:1

Total number of routes: 2

Network NextHop MED LocPrf PrefVal Path/Ogn

* >i [2][0][48][7010-0000-0001][0][0.0.0.0]/104

7.7.7.7 0 100 0 i

* i 7.7.7.7 0 100 0 i

Route distinguisher of public instance: 1:15

Total number of routes: 1

Network NextHop MED LocPrf PrefVal Path/Ogn

* >e [2][0][48][0011-0022-0033][32][11.22.33.55]/136

30.30.1.2 0 0 100i

Table 1 Command output

Field	Description
Status codes	Route status codes: · * - valid—Valid route. · > - best—Optimal route. · d - dampened—Dampened route. · h - history—History route. · i - internal—Internal route. · e - external—External route. · s - suppressed—Suppressed route. · S - Stale—Stale route. · a - additional-path—Add-Path optimal route.
Origin	Origin of the route: · i – IGP—Originated in the AS. The origin of routes advertised by using the network command is IGP. · e – EGP—Learned through EGP. · ? – incomplete—Unknown origin. The origin of routes redistributed from IGP protocols is incomplete.
Network	BGP EVPN route/route length. BGP EVPN routes are as follows: · [1][ESI][EthernetTagID] ? 1—Ethernet auto-discovery route. ? ESI—Ethernet segment identifier (ESI). ? EthernetTagID—Ethernet tag ID. · [2][EthernetTagID][MACLength][MAC][IPAddressLength][IPAddress] ? 2—MAC/IP advertisement route. ? EthernetTagID—Ethernet tag ID. ? MACLength—MAC address length. ? MAC—MAC address. ? IPAddressLength—IP address length. ? IPAddress—IP address. · [3][EthernetTagID][IPAddressLength][IPAddress] ? 3—IMET route. ? IPAddressLength—IP address length. ? IPAddress—IP address of the originating router. · [4][ESI][IPAddressLength][IPAddress] ? 4—ES route. ? ESI—ESI. ? IPAddressLength—IP address length. ? IPAddress—IP address of the originating router. · [5][EthernetTagID][IPAddressLength][IPAddress] ? 5—IP prefix advertisement route. ? EthernetTagID—Ethernet tag ID. ? IPAddressLength—IP address length. ? IPAddress—IP address of the originating router. · [6][EthernetTagID][Source Len][Source IP][Group Len][Group IP][Originator Len][Originator IP] ? 6—Selective multicast Ethernet tag route. ? EthernetTagID—Ethernet tag ID. ? Source Len—Length of the multicast source address. This field displays 0 if the multicast source is any (, G). ? Source IP—Source IP address of IGMP membership reports. This field is not displayed if the multicast source is any (, G). ? Group Len—Length of the multicast group address. ? Group IP—Multicast group address of IGMP membership reports. ? Originator Len—Length of the originating router's IP address. ? Originator IP—IP address of the originating router. · [7][ESI][EthernetTagID][Source Len][Source IP][Group Len][Group IP][Originator Len][Originator IP] ? 7—IGMP join synch route. ? ESI—ESI. ? EthernetTagID—Ethernet tag ID. ? Source Len—Length of the multicast source address. This field displays 0 if the multicast source is any (, G). ? Source IP—Source IP address of IGMP membership reports. This field is not displayed if the multicast source is any (, G). ? Group Len—Length of the multicast group address. ? Group IP—Multicast group address of IGMP membership reports. ? Originator Len—Length of the originating router's IP address. ? Originator IP—IP address of the originating router. · [8][ESI][EthernetTagID] [Source Len][Source IP][Group Len][Group IP][Originator Len][Originator IP][ [LeaveGroup Synchronization] ? 8—IGMP leave synch route. ? ESI—ESI. ? EthernetTagID—Ethernet tag ID. ? Source Len—Length of the multicast source address. This field displays 0 if the multicast source is any (, G). ? Source IP—Source IP address of IGMP membership reports. This field is not displayed if the multicast source is any (, G). ? Group Len—Length of the multicast group address. ? Group IP—Multicast group address of IGMP membership reports. ? Originator Len—Length of the originating router's IP address. ? Originator IP—IP address of the originating router. ? LeaveGroup Synchronization—Leave group synchronization sequence number.
NextHop	Next hop IP address.
MED	Multi-Exit Discriminator (MED) attribute.
LocPrf	Local precedence.
PrefVal	Preferred value.
Path/Ogn	AS_PATH and ORIGIN attributes of the route.

# Display detailed information about BGP EVPN route [1][0001.0203.0405.0607.0809][5]/120 with RD 1.1.1.1:100.

<Sysname> display bgp l2vpn evpn route-distinguisher 1.1.1.1:100 [1][0001.0203.0405.0607.0809][5] 120

BGP local router ID: 172.16.250.133

Local AS number: 100

Route distinguisher: 1.1.1.1:100

Total number of routes: 1

Paths: 1 available, 1 best

BGP routing table information of [1][0001.0203.0405.0607.0809][5]/120:

From : 10.1.1.2 (192.168.56.17)

Rely nexthop : 10.1.1.2

Original nexthop: 10.1.1.2

OutLabel : NULL

Ext-Community : <RT: 1:2>, <Encapsulation Type: VXLAN >, <ESI Label: Flag 0,

Label 1>

RxPathID : 0x0

TxPathID : 0x0

AS-path : 200

Origin : igp

Attribute value : MED 0, pref-val 0

State : valid, external, best

IP precedence : N/A

QoS local ID : N/A

Traffic index : N/A

EVPN route type : Ethernet auto-discovery route

ESI : 0001.0203.0405.0607.0809

Ethernet tag ID : 5

MPLS label : 10

Table 2 Command output

Field	Description
Paths	Number of routes: · available—Number of valid routes. · best—Number of optimal routes.
From	IP address of the BGP peer that advertised the route.
Rely Nexthop	Next hop after route recursion. If no next hop is found, this field displays not resolved.
Original nexthop	Original next hop of the route. If the route was obtained from a BGP update message, the original next hop is the next hop IP address in the message.
OutLabel	Outgoing label of the route.
Ext-Community	Extended community attributes: · RT. · Encapsulation Type. · ESI Label.
RxPathID	Add-Path ID value of the received route. This field is not supported by the BGP EVPN address family.
TxPathID	Add-Path ID value of the sent route. This field is not supported by the BGP EVPN address family.
AS-path	AS_PATH attribute of the route. This attribute records the ASs the route has passed and avoids routing loops.
Origin	Origin of the route: · igp—Originated in the AS. The origin of routes advertised by using the network command is IGP. · egp—Learned through EGP. · incomplete—Unknown origin. The origin of routes redistributed from IGP protocols is incomplete.
Attribute value	Attributes of the route: · MED—MED value for the destination network. · localpref—Local preference value. · pref-val—Preferred value. · pre—Route preference value.
State	Current state of the route: · valid. · internal. · external. · local. · synchronize. · best.
IP precedence	IP precedence in the range of 0 to 7. N/A indicates that the IP precedence is invalid.
QoS local ID	QoS local ID in the range of 1 to 4095. N/A indicates that the QoS local ID is invalid.
Traffic index	Traffic index in the range of 1 to 64. N/A indicates that the traffic index is invalid.
MPLS label	MPLS label. The current software version does not support this field.

‌

# Display detailed information about BGP EVPN route [2][5][48][0001-0203-0405][32][4.5.5.5]/136 with RD 1.1.1.1:100.

<Sysname> display bgp l2vpn evpn route-distinguisher 1.1.1.1:100 [2][5][48][0001-0203-0405][32][5.5.5.5] 136

BGP local router ID: 172.16.250.133

Local AS number: 100

Route distinguisher: 1.1.1.1:100

Total number of routes: 1

Paths: 1 available, 1 best

BGP routing table information of [2][5][48][0001-0203-0405][32][5.5.5.5]/136:

From : 10.1.1.2 (192.168.56.17)

Rely nexthop : 10.1.1.2

Original nexthop: 10.1.1.2

OutLabel : NULL

Ext-Community : <RT: 1:2>, <RT: 1:3>, <RT: 1:4>, <RT: 1:5>, <RT: 1:6>, <RT: 1:7

>, <Encapsulation Type: VXLAN>, <Router's Mac: 0006-0708-0910

>, <MAC Mobility: Flag 0, SeqNum 2>, <Default GateWay>

RxPathID : 0x0

TxPathID : 0x0

AS-path : 200

Origin : igp

Attribute value : MED 0, pref-val 0

State : valid, external, best

IP precedence : N/A

QoS local ID : N/A

Traffic index : N/A

EVPN route type : MAC/IP advertisement route

ESI : 0001.0203.0405.0607.0809

Ethernet tag ID : 5

MAC address : 0001-0203-0405

IP address : 5.5.5.5/32

MPLS label1 : 10

MPLS label2 : 0

Table 3 Command output

Field	Description
Ext-Community	Extended community attributes: · RT. · Encapsulation Type. · Router's Mac. · MAC Mobility—MAC mobility. ? Flag—Indicates whether the MAC address can move. A value of 1 indicates that the MAC address cannot move, and a value of 0 indicates that the MAC address can move. ? SeqNum—Identifies the most recent move of the MAC address. · Default GateWay—Route for the default gateway.
MPLS label1	VXLAN ID used for Layer 2 forwarding.
MPLS label2	L3 VXLAN ID used for Layer 3 forwarding.

‌

# Display detailed information about BGP EVPN route [3][0][32][5.5.5.5]/80 with RD 1.1.1.1:100.

<Sysname> display bgp l2vpn evpn route-distinguisher 1.1.1.1:100 [3][0][32][4.5.5.5] 80

BGP local router ID: 172.16.250.133

Local AS number: 100

Route distinguisher: 1.1.1.1:100

Total number of routes: 1

Paths: 1 available, 1 best

BGP routing table information of [3][0][32][4.5.5.5]/80:

From : 10.1.1.2 (192.168.56.17)

Rely nexthop : 10.1.1.2

Original nexthop: 10.1.1.2

OutLabel : NULL

Ext-Community : <RT: 1:2>, <Encapsulation Type: VXLAN>

RxPathID : 0x0

TxPathID : 0x0

PMSI tunnel : Flag 0, TunnelType 6, Label 10, EndPointAddress 10.1.1.2

AS-path : 200

Origin : igp

Attribute value : MED 0,pref-val 0

State : valid, external, best

IP precedence : N/A

QoS local ID : N/A

Traffic index : N/A

EVPN route type : Inclusive multicast Ethernet tag route

Ethernet tag ID : 0

Origin address : 5.5.5.5/32

Table 4 Command output

Field	Description
Ext-Community	Extended community attributes: · RT. · Encapsulation Type.
PMSI tunnel	P-Multicast Service Interface (PMSI) tunnel information: · Flag—This field is fixed at 0 in the current software version. · TunnelType—This field is fixed at 6 in the current software version, which represents a head-end replication tunnel. · Label—VXLAN ID. · EndPointAddress—Tunnel destination address.
Origin address	IP address of the originating router.

# Display detailed information about BGP EVPN route [4][0000.0000.0000.0000.000a][32][4.5.5.5]/128 with RD 1.1.1.1:100.

<Sysname> display bgp l2vpn evpn route-distinguisher 1.1.1.1:100 [4][0000.0000.0000.0000.000a][32][4.5.5.5] 128

BGP local router ID: 172.16.250.133

Local AS number: 100

Route distinguisher: 1.1.1.1:100

Total number of routes: 1

Paths: 1 available, 1 best

BGP routing table information of [4][0000.0000.0000.0000.000a][32][4.5.5.5]/128:

From : 10.1.1.2 (192.168.56.17)

Rely nexthop : 10.1.1.2

Original nexthop: 10.1.1.2

OutLabel : NULL

Ext-Community : <RT: 1:2>, <Encapsulation Type: VXLAN>, <ES-Import RT: 1:1>

RxPathID : 0x0

TxPathID : 0x0

AS-path : 200

Origin : igp

Attribute value : MED 0,pref-val 0

State : valid, external, best

IP precedence : N/A

QoS local ID : N/A

Traffic index : N/A

EVPN route type : Ethernet segment route

ESI : 0000.0000.0000.0000.000a

Origin address : 4.5.5.5/32

Table 5 Command output

Field	Description
Ext-Community	Extended community attributes: · RT. · Encapsulation Type. · ES-Import RT.
Origin address	IP address of the originating router.

Field

Description

Ext-Community

Extended community attributes:

· RT.

· Encapsulation Type.

· ES-Import RT.

Origin address

IP address of the originating router.

# Display detailed information about BGP EVPN route [5][10][32][4.5.5.5]/80 with RD 1.1.1.1:100.

<Sysname> display bgp l2vpn evpn route-distinguisher 1.1.1.1:100 [5][10][32][4.5.5.5] 80

BGP local router ID: 172.16.250.133

Local AS number: 100

Route distinguisher: 1.1.1.1:100

Total number of routes: 1

Paths: 1 available, 1 best

BGP routing table information of [5][10][32][4.5.5.5]/80:

From : 10.1.1.2 (192.168.56.17)

Rely nexthop : 10.1.1.2

Original nexthop: 10.1.1.2

OutLabel : NULL

Ext-Community : <RT: 1:2>, <Encapsulation Type: VXLAN>, <Router's Mac:

0006-0708-0910>

RxPathID : 0x0

TxPathID : 0x0

AS-path : 200

Origin : igp

Attribute value : MED 0,pref-val 0

State : valid, external, best

IP precedence : N/A

QoS local ID : N/A

Traffic index : N/A

EVPN route type : IP prefix advertisement route

ESI : 0000.0000.0000.0000.000a

Ethernet tag ID : 10

IP address : 4.5.5.5/32

Gateway address : 0.0.0.0

MPLS Label : 1

Table 6 Command output

Field	Description
Ext-Community	Extended community attributes: · RT. · Encapsulation Type. · Router's Mac.
IP address	IP address and prefix length.
MPLS Label	L3 VXLAN ID used for Layer 3 forwarding.

‌

# Display detailed information about BGP EVPN route [6][0][32][10.1.1.1][32][224.224.224.224][32][192.168.3.1]/160 with RD 1.1.1.1:100.

<Sysname> display bgp l2vpn evpn route-distinguisher 1.1.1.1:100 [6][0][32][10.1.1.1][32][224.224.224.224][32][192.168.3.1] 160

BGP local router ID: 172.16.250.133

Local AS number: 100

Route distinguisher: 1.1.1.1:100

Total number of routes: 1

Paths: 1 available, 1 best

BGP routing table information of [6][0][32][10.1.1.1][32][224.224.224.224][32][192.168.3.1]/160:

From : 10.1.1.2

Rely nexthop : 10.1.1.2

Original nexthop: 10.1.1.2

OutLabel : NULL

Ext-Community : <RT: 1:2>, <Encapsulation Type: VXLAN>,

RxPathID : 0x0

TxPathID : 0x0

AS-path : 200

Origin : igp

Attribute value : MED 0,pref-val 0

State : valid, external, best

IP precedence : N/A

QoS local ID : N/A

Traffic index : N/A

EVPN route type : Selective multicast Ethernet tag route

Ethernet tag ID : 0

Source length : 32

Source address : 10.1.1.1

Group length : 32

Group address : 224.224.224.224

Origin address : 192.168.3.1

IGMP flags : v3, include

Table 7 Command output

Field	Description
Ext-Community	Extended community attributes: · RT. · Encapsulation Type.
Source length	Length of the multicast source address.
Source address	Multicast source address.
Group length	Length of the multicast group address.
Group address	Multicast group address.
Origin address	IP address of the originating router.

# Display detailed information about BGP EVPN route [7][00:00:00:00:00:00:00:00:00][0][32][10.1.1.1][32][224.224.224.224][32][192.168.3.1]/240 with RD 1.1.1.1:100.

<Sysname> display bgp l2vpn evpn route-distinguisher 1.1.1.1:100 [7][0000.0000.0000.0000.0000][0][32][10.1.1.1][16][224.224.224.224][32][192.168.3.1] 240

BGP local router ID: 172.16.250.133

Local AS number: 100

Route distinguisher: 1.1.1.1:100

Total number of routes: 1

Paths: 1 available, 1 best

BGP routing table information of [7][0000.0000.0000.0000.0000][0][32][10.1.1.1][32][224.224.224.224][32][192.168.3.1]/240:

From : 10.1.1.2

Rely nexthop : 10.1.1.2

Original nexthop: 10.1.1.2

OutLabel : NULL

Ext-Community : <RT: 1:2>, <Encapsulation Type: VXLAN>, < ESI-RT: 0:0>

RxPathID : 0x0

TxPathID : 0x0

AS-path : 200

Origin : igp

Attribute value : MED 0,pref-val 0

State : valid, external, best

IP precedence : N/A

QoS local ID : N/A

Traffic index : N/A

EVPN route type : IGMP join synch route

ESI : 0000.0000.0000.0000.0000

Ethernet tag ID : 0

Source length : 32

Source address : 10.1.1.1

Group length : 32

Group address : 224.224.224.224

Origin address : 192.168.3.1

IGMP flags : v3, include

Table 8 Command output

Field	Description
Ext-Community	Extended community attributes: · RT. · Encapsulation Type. · EVI-RT—Route target associated with EVI.
Source length	Length of the multicast source address.
Source address	Multicast source address.
Group length	Length of the multicast group address.
Group address	Multicast group address.
Origin address	IP address of the originating router.

# Display detailed information about BGP EVPN route [8][ 00:00:00:00:00:00:00:00:00][0][32][10.1.1.1][32][224.224.224.224][32][192.168.3.1][0]/272 with RD 1.1.1.1:100.

<Sysname> display bgp l2vpn evpn route-distinguisher 1.1.1.1:100 [8][0000.0000.0000.0000.0000][0][32][10.1.1.1][32][224.224.224.224][32][192.168.3.1][0] 272

BGP local router ID: 172.16.250.133

Local AS number: 100

Route distinguisher: 1.1.1.1:100

Total number of routes: 1

Paths: 1 available, 1 best

BGP routing table information of [8][0000.0000.0000.0000.0000] [0][32][10.1.1.1][32][224.224.224.224][32][192.168.3.1][0]/272:

From : 10.1.1.2

Rely nexthop : 10.1.1.2

Original nexthop: 10.1.1.2

OutLabel : NULL

Ext-Community : <RT: 1:2>, <Encapsulation Type: VXLAN>, < ESI-RT: 1:200>

RxPathID : 0x0

TxPathID : 0x0

AS-path : 200

Origin : igp

Attribute value : MED 0,pref-val 0

State : valid, external, best

IP precedence : N/A

QoS local ID : N/A

Traffic index : N/A

EVPN route type : IGMP leave synch route

ESI : 0000.0000.0000.0000.0000

Ethernet tag ID : 0

Source length : 32

Source address : 10.1.1.1

Group length : 32

Group address : 224.224.224.224

Origin address : 192.168.3.1

Leave group sync: 0

Max ResponseTime: 2500ms

Max ResponseCode: 25

IGMP flags : v3, include

Table 9 Command output

Field	Description
Ext-Community	Extended community attributes: · RT. · Encapsulation Type. · ESI-RT—Route target associated with the ESI.
Source length	Length of the multicast source address.
Source address	Multicast source address.
Group length	Length of the multicast group address.
Group address	Multicast group address.
Origin address	IP address of the originating router.
Leave group sync	Leave group synchronization sequence number.
Max ResponseTime	Maximum response time in milliseconds.
Max ResponseCode	Maximum response time in the received packet, in deciseconds.

‌

# Display detailed information about BGP EVPN route [4][0000.0000.0000.0000.000a][32][4.5.5.5]/128 with RD 1.1.1.1:100.

<Sysname> display bgp l2vpn evpn route-distinguisher 1.1.1.1:100 [4][0000.0000.0000.0000.000a] [32][4.5.5.5] 128 advertise-info

BGP local router ID: 172.16.250.133

Local AS number: 100

Route distinguisher: 1.1.1.1:100

Total number of routes: 1

Paths: 1 best

BGP routing table information of [4][0000.0000.0000.0000.000a][32][4.5.5.5]/128:

Advertised to peers (1 in total):

10.2.1.2

Table 10 Command output

Field	Description
Paths	Number of optimal routes.
Advertised to peers (1 in total)	Peers to whom the route has been advertised and the number of the peers.

‌

display evpn auto-discovery

Use display evpn auto-discovery to display information about peers that are automatically discovered through BGP.

Syntax

display evpn auto-discovery { imet [ peer ip-address] [ vsi vsi-name ] | mac-ip | macip-prefix [ nexthop next-hop ] [ count ] }

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

imet: Specifies peers discovered through IMET routes.

peer ip-address: Specifies a peer by its IP address. If you do not specify this option, the command displays information about all automatically discovered peers.

vsi vsi-name: Specifies a VSI by its name, a case-sensitive string of 1 to 31 characters. If you do not specify this option, the command displays peer information for all VSIs.

mac-ip: Specifies peers discovered through MAC/IP advertisement routes that do not carry L3 VXLAN IDs.

macip-prefix: Specifies peers discovered through MAC/IP advertisement routes that carry L3 VXLAN IDs or IP prefix advertisement routes that carry L3 VXLAN IDs.

nexthop next-hop: Specifies a next hop. If you do not specify this option, the command displays peer information for all next hops.

count: Displays the number of peers. If you do not specify this keyword, the command displays detailed peer information.

Examples

# Display information about peers discovered through IMET routes.

<Sysname> display evpn auto-discovery imet

Total number of automatically discovered peers: 2

VSI name: vpna

RD PE_address Tunnel_address Tunnel mode VXLAN ID

1:10 2.2.2.2 2.2.2.2 VXLAN 10

2:100 3.3.3.3 3.3.3.3 VXLAN 10

Table 11 Command output

Field	Description
PE_address	Identifier of the remote VTEP on the VSI.
Tunnel_address	Tunnel destination IP address.
Tunnel mode	Tunnel mode: · VXLAN. · VXLAN-DCI.

# Display information about peers discovered through MAC/IP advertisement routes that do not carry L3 VXLAN IDs.

<Sysname> display evpn auto-discovery mac-ip

Total number of automatically discovered peers: 1

VSI name: vpna

Destination IP Source IP VXLAN ID Tunnel mode Tunnel name

6.6.6.6 1.1.1.9 100 VXLAN Tunnel1

Table 12 Command output

Field	Description
Destination IP	Tunnel destination IP address.
Source IP	Tunnel source IP address.
Tunnel mode	Tunnel mode. VXLAN represents a VXLAN tunnel.

# Display information about peers discovered through MAC/IP advertisement routes that carry L3 VXLAN IDs or IP prefix advertisement routes that carry L3 VXLAN IDs.

<Sysname> display evpn auto-discovery macip-prefix

Destination IP Source IP L3VNI Tunnel mode Outgoing interface

1.1.1.1 3.3.3.3 200 VXLAN Vsi-interface3

2.2.2.2 3.3.3.3 200 VXLAN Vsi-interface3

# Display the total number of peers discovered through MAC/IP advertisement routes that carry L3 VXLAN IDs or IP prefix advertisement routes that carry L3 VXLAN IDs.

<Sysname> display evpn auto-discovery macip-prefix count

Total number of entries: 2

Table 13 Command output

Field	Description
Destination IP	Tunnel destination IP address.
Source IP	Tunnel source IP address.
L3VNI	L3 VXLAN ID used for Layer 3 forwarding.
Tunnel mode	Tunnel mode: · VXLAN. · VXLAN-DCI.
Outgoing interface	VSI interface associated with the L3 VXLAN ID.

‌

display evpn route arp

Use display evpn route arp to display EVPN ARP entries.

Syntax

display evpn route arp [ local | remote ] [ public-instance | vpn-instance vpn-instance-name ] [ count ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

local: Specifies local ARP entries.

remote: Specifies remote ARP entries.

public-instance: Specifies the public instance.

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters.

count: Displays the number of ARP entries. If you do not specify this keyword, the command displays detailed information about ARP entries.

Usage guidelines

If you do not specify the local or remote keyword, this command displays both local and remote EVPN ARP entries.

If you do not specify the public-instance keyword or the vpn-instance vpn-instance-name option, this command displays EVPN ARP entries for the public instance and all VPN instances.

Examples

# Display all EVPN ARP entries.

<Sysname> display evpn route arp

Flags: D - Dynamic B - BGP L - Local active

G - Gateway S - Static M - Mapping I - Invalid

VPN instance: vpn1 Interface: Vsi-interface1

IP address MAC address Router MAC VSI index Flags

10.1.1.1 0003-0003-0003 a0ce-7e40-0400 0 GL

10.1.1.11 0001-0001-0001 a0ce-7e40-0400 0 DL

10.1.1.12 0001-0001-0011 a0ce-7e41-0401 0 B

10.1.1.13 0001-0001-0021 a0ce-7e42-0402 0 B

10.1.1.101 0001-0011-0101 a0ce-7e40-0400 0 SL

10.1.1.102 0001-0011-0102 0011-9999-0000 0 BS

Public instance Interface: Vsi-interface2

IP address MAC address Router MAC VSI index Flags

11.1.1.1 0033-0033-0033 a0ce-7e40-0400 0 GL

11.1.1.11 0011-0011-0011 a0ce-7e40-0400 0 DL

# Display the total number of EVPN ARP entries.

<Sysname> display evpn route arp count

Total number of entries: 8

Table 14 Command output

Field	Description
Interface	VSI interface.
Flags	ARP entry type: · D—The entry is dynamically learned. · B—The entry is learned from BGP EVPN routes. · L—The local entry is active. If this flag is not set and the B flag is set, the entry learned from BGP EVPN routes is active. · G—The entry for the gateway is active. · S—The static entry is active. · M—The entry from a remote VXLAN mapped to a local VXLAN is active. · I—The entry is invalid. Reasons: ? The VSI has been administratively shut down by using the shutdown command. ? The outgoing tunnel interface does not exist.

Field

Description

Interface

VSI interface.

Flags

ARP entry type:

· D—The entry is dynamically learned.

· B—The entry is learned from BGP EVPN routes.

· L—The local entry is active. If this flag is not set and the B flag is set, the entry learned from BGP EVPN routes is active.

· G—The entry for the gateway is active.

· S—The static entry is active.

· M—The entry from a remote VXLAN mapped to a local VXLAN is active.

· I—The entry is invalid. Reasons:

? The VSI has been administratively shut down by using the shutdown command.

? The outgoing tunnel interface does not exist.

display evpn route arp suppression

Use display evpn route arp suppression to display EVPN ARP flood suppression entries.

Syntax

display evpn route arp suppression [ local | remote ] [ vsi vsi-name ] [ count ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

local: Specifies local ARP flood suppression entries.

remote: Specifies remote ARP flood suppression entries.

vsi vsi-name: Specifies a VSI by its name, a case-sensitive string of 1 to 31 characters. If you do not specify this option, the command displays ARP flood suppression entries for all VSIs.

count: Displays the number of ARP flood suppression entries. If you do not specify this keyword, the command displays detailed information about ARP flood suppression entries.

Usage guidelines

If you do not specify the local or remote keyword, this command displays both local and remote EVPN ARP flood suppression entries.

Examples

# Display all EVPN ARP flood suppression entries.

<Sysname> display evpn route arp suppression

Flags: D - Dynamic B - BGP L - Local active

G - Gateway S - Static M - Mapping I - Invalid

VSI name: vpna

IP address MAC address Flags

10.1.1.12 0002-0002-0002 B

10.1.1.13 0002-0002-0002 BI

10.1.1.101 0001-0011-0101 BS

10.1.1.102 0001-0011-0102 DL

# Display the total number of ARP flood suppression entries.

<Sysname> display evpn route arp suppression count

Total number of entries: 4

Table 15 Command output

Field	Description
Flags	ARP flood suppression entry type: · D—The entry is dynamically learned. · B—The entry is learned from BGP EVPN routes. · L—The local entry is active. If this flag is not set and the B flag is set, the entry learned from BGP EVPN routes is active. · G—The entry for the gateway is active. · S—The static entry is active. · M—The entry from a remote VXLAN mapped to a local VXLAN is active. · I—The entry is invalid. Reasons: ? The VSI has been administratively shut down by using the shutdown command. ? The outgoing tunnel interface does not exist.

Field

Description

Flags

ARP flood suppression entry type:

· D—The entry is dynamically learned.

· B—The entry is learned from BGP EVPN routes.

· L—The local entry is active. If this flag is not set and the B flag is set, the entry learned from BGP EVPN routes is active.

· G—The entry for the gateway is active.

· S—The static entry is active.

· M—The entry from a remote VXLAN mapped to a local VXLAN is active.

· I—The entry is invalid. Reasons:

? The VSI has been administratively shut down by using the shutdown command.

? The outgoing tunnel interface does not exist.

display evpn route mac

Use display evpn route mac to display EVPN MAC address entries.

Syntax

display evpn route mac [ local | remote ] [ vsi vsi-name ] [ count ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

local: Specifies local MAC address entries.

remote: Specifies remote MAC address entries.

vsi vsi-name: Specifies a VSI by its name, a case-sensitive string of 1 to 31 characters. If you do not specify this option, the command displays MAC address entries for all VSIs.

count: Displays the number of MAC address entries. If you do not specify this keyword, the command displays detailed information about MAC address entries.

Usage guidelines

If you do not specify the local or remote keyword, this command displays both local and remote EVPN MAC address entries.

Examples

# Display all EVPN MAC address entries.

<Sysname> display evpn route mac

Flags: D - Dynamic B - BGP L - Local active

G - Gateway S - Static M - Mapping I - Invalid

VSI name: bbb

MAC address Link ID/Name Flags Next hop

0000-0000-000a 1 DL -

0000-0000-0009 Tunnel1 B 2.2.2.2

0001-2000-4000 - BI 3.3.3.3

# Display the total number of EVPN MAC address entries.

<Sysname> display evpn route mac count

Total number of entries: 3

Table 16 Command output

Field	Description
Link ID/Name	For a local MAC address, this field displays the AC's link ID on the VSI. For a remote MAC address, this field displays the tunnel interface name.
Flags	MAC address entry type: · D—The entry is dynamically learned. · B—The entry is learned from BGP EVPN routes. · L—The local entry is active. If this flag is not set and the B flag is set, the entry learned from BGP EVPN routes is active. · G—The entry for the gateway is active. · S—The static entry is active. · M—The entry from a remote VXLAN mapped to a local VXLAN is active. · I—The entry is invalid. Reasons: ? The VSI has been administratively shut down by using the shutdown command. ? The outgoing tunnel interface does not exist.
Next hop	IP address of the remote VTEP. If the MAC address entry is a local entry, a hyphen (-) is displayed.

display evpn route nd

Use display evpn route nd to display EVPN ND entries.

Syntax

display evpn route nd [ local | remote ] [ public-instance | vpn-instance vpn-instance-name ] [ count ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

local: Specifies local ND entries.

remote: Specifies remote ND entries.

public-instance: Specifies the public instance.

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters.

count: Displays the number of ND entries. If you do not specify this keyword, the command displays detailed information about ND entries.

Usage guidelines

If you do not specify the local or remote keyword, this command displays both local and remote EVPN ND entries.

If you do not specify the public-instance keyword or the vpn-instance vpn-instance-name option, this command displays EVPN ND entries for the public instance and all VPN instances.

Examples

# Display all EVPN ND entries.

<Sysname> display evpn route nd

Flags: D - Dynamic B - BGP L - Local active

G - Gateway S - Static M - Mapping

VPN instance: vpn1 Interface: Vsi-interface1

IPv6 address : AD80:0300:1000:0050:0200:0300:0100:0012

MAC address : 0001-0001-0001 Router MAC : a0ce-7e40-0400

VSI index : 0 Flags : GL

IPv6 address : AD10:0300:1000:0020:0200:0300:0100:0022

MAC address : 0001-0001-0002 Router MAC : a0ce-7e40-0411

VSI index : 0 Flags : GL

Public instance Interface: Vsi-interface1

IPv6 address : BC80:0300:1000:0050:0200:0300:0100:0033

MAC address : 0002-0002-0001 Router MAC : a0ce-7e40-0422

VSI index : 0 Flags : GL

IPv6 address : BC10:0300:1000:0020:0200:0300:0100:0034

MAC address : 0002-0002-0002 Router MAC : a0ce-7e40-0433

VSI index : 0 Flags : GL

# Display the total number of EVPN ND entries.

<Sysname>display evpn route nd count

Total number of entries: 2

Table 17 Command output

Field	Description
Interface	VSI interface.
Flags	ND entry type: · D—The entry is dynamically learned. · B—The entry is learned from BGP EVPN routes. · L—The local entry is active. If this flag is not set and the B flag is set, the entry learned from BGP EVPN routes is active. · G—The entry for the gateway is active. · S—The static entry is active. This type is not supported in the current software version. · M—The entry from a remote VXLAN mapped to a local VXLAN is active.

Field

Description

Interface

VSI interface.

Flags

ND entry type:

· D—The entry is dynamically learned.

· B—The entry is learned from BGP EVPN routes.

· L—The local entry is active. If this flag is not set and the B flag is set, the entry learned from BGP EVPN routes is active.

· G—The entry for the gateway is active.

· S—The static entry is active. This type is not supported in the current software version.

· M—The entry from a remote VXLAN mapped to a local VXLAN is active.

display evpn routing-table

Use display evpn routing-table to display the EVPN routing table for a VPN instance.

Syntax

display evpn routing-table [ ipv6 ] { public-instance | vpn-instance vpn-instance-name } [ count ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

ipv6: Specifies IPv6 information. If you do not specify this keyword, the command displays IPv4 information.

public-instance: Specifies the public instance.

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters.

count: Displays the number of entries in the routing table. If you do not specify this keyword, the command displays detailed information about the routing table.

Examples

# Display the EVPN IPv4 routing table for VPN instance vpn1.

<Sysname> display evpn routing-table vpn-instance vpn1

Flags: E - with valid ESI A – A-D ready L - Local ES exists

VPN instance name: vpn1 Local L3VNI: 7

IP address Nexthop Outgoing interface NibID Flags

10.1.1.11 1.1.1.1 Vsi-interface3 0x18000000 EAL

10.1.1.12 2.2.2.2 Vsi-interface3 0x18000001 EA

# Display the EVPN IPv4 routing table for the public instance.

<Sysname> display evpn routing-table public-instance

Flags: E - with valid ESI A – A-D ready L - Local ES exists

Public instance Local L3VNI: 3900

IP address Nexthop Outgoing interface NibID Flags

10.1.1.11 1.1.1.1 Vsi-interface3 0x18000000 EAL

10.1.1.12 2.2.2.2 Vsi-interface3 0x18000001 EA

# Display the number of EVPN route entries in the IPv4 routing table for VPN instance vpn1.

<Sysname> display evpn routing-table vpn-instance vpn1 count

Total number of entries: 2

# Display the EVPN IPv6 routing table for VPN instance vpna.

<Sysname> display evpn routing-table ipv6 vpn-instance vpna

VPN instance: vpna Local L3VNI: 7

IPv6 address : BC10:0300:1000:0020:0200:0300:0100:0034

Next hop : 1.1.1.1

Outgoing interface : Vsi-interface3

NibID : 0x18000000

IPv6 address : BC10:0300:1000:0020:0200:0300:0100:0035

Next hop : 2.2.2.2

Outgoing interface : Vsi-interface3

NibID : 0x18000001

Table 18 Command output

Field	Description
Local L3VNI	L3 VXLAN ID associated with the VPN instance or the public instance.
NibID	Next hop ID.
Flags	Flags of the route: · E—The route carries a valid ESI. · A—All Ethernet auto-discovery routes are received. The ECMP routes for the next hop can be issued. · L—An active local ESI exists. Remote routes are not issued. · -—The MAC/IP advertisement route does not have a valid ESI. ECMP routes are not supported.

evpn edge group

Use evpn edge group to configure a virtual ED address.

Use undo evpn edge group to restore the default.

Syntax

evpn edge group group-ip

undo evpn edge group

Default

No virtual ED address is configured.

Views

System view

Predefined user roles

network-admin

Parameters

group-ip: Specifies the virtual ED address.

Usage guidelines

For high availability and load sharing, you can deploy two EDs at a data center. To virtualize the redundant EDs into one device, you must configure the same virtual ED address on them. The redundant EDs use the virtual ED address to establish tunnels with VTEPs and remote EDs.

Redundant EDs cannot provide access service for local VMs. They can act only as EDs. For correct communication, do not redistribute external routes on only one of the redundant EDs. However, you can redistribute the same external routes on both EDs.

On a redundant ED, the virtual ED address must be the IP address of a loopback interface, and it cannot be the BGP peer IP address of the ED.

Examples

# Configure 1.2.3.4 as the virtual ED address.

<Sysname> system-view

[Sysname] evpn edge group 1.2.3.4

evpn encapsulation

Use evpn encapsulation to create an EVPN instance and enter its view, or enter the view of an existing EVPN instance.

Use undo evpn encapsulation to restore the default.

Syntax

evpn encapsulation vxlan

undo evpn encapsulation

Default

No EVPN instance exists.

Views

VSI view

Predefined user roles

network-admin

Parameters

vxlan: Specifies VXLAN encapsulation.

Usage guidelines

Before you can configure EVPN settings, you must create an EVPN instance.

Examples

# Create an EVPN instance and enter its view.

<Sysname> system-view

[Sysname] vsi aaa

[Sysname-vsi-aaa] evpn encapsulation vxlan

[Sysname-vsi-aaa-evpn-vxlan]

evpn route arp-mobility suppression

Use evpn route arp-mobility suppression to enable ARP mobility event suppression.

Use undo evpn route arp-mobility suppression to disable ARP mobility event suppression.

Syntax

evpn route arp-mobility suppression

undo evpn route arp-mobility suppression

Default

ARP mobility event suppression is disabled.

Views

System view

Predefined user roles

network-admin

Usage guidelines

Misconfiguration of IP addresses might cause two sites attached to different distributed EVPN gateways to contain the same IP address. In this condition, the gateways constantly synchronize and update EVPN ARP entries and determine that ARP mobility events occur. As a result, an inter-site loop might occur, and the bandwidth is occupied by ARP entry synchronization traffic. To eliminate loops and suppress those ARP mobility events, enable ARP mobility event suppression on distributed EVPN gateways. This feature allows an IP address to move at most four times between sites within 180 seconds. If an IP address moves more than four times within 180 seconds, distributed EVPN gateways suppress the excess ARP mobility events and do not advertise ARP information for the IP address.

Examples

# Enable ARP mobility event suppression.

<Sysname> system-view

[Sysname] evpn route arp-mobility suppression

export route-policy

Use export route-policy to apply an export routing policy to EVPN on a VPN instance.

Use undo export route-policy to restore the default.

Syntax

export route-policy route-policy

undo export route-policy

Default

No export routing policy is applied to EVPN on a VPN instance.

Views

VPN instance EVPN view

Predefined user roles

network-admin

Parameters

route-policy: Specifies a routing policy by its name, a case-sensitive string of 1 to 63 characters.

Usage guidelines

You can specify an export routing policy to filter advertised routes or modify their route attributes for EVPN.

If you execute this command multiple times, the most recent configuration takes effect.

EVPN can use an export routing policy specified in VPN instance view or in VPN instance EVPN view. Export routing policy configuration in VPN instance EVPN view takes precedence over that in VPN instance view.

Examples

# Apply export routing policy poly-1 to EVPN on VPN instance vpn1.

<Sysname> system-view

[Sysname] ip vpn-instance vpn1

[Sysname-vpn-instance-vpn1] address-family evpn

[Sysname-vpn-evpn-vpn1] export route-policy poly-1

Related commands

route-policy (Layer 3—IP Routing Command Reference)

import evpn mac-ip

Use import evpn mac-ip to enable the device to redistribute received MAC/IP advertisement routes that contain ARP or ND information into a BGP unicast routing table.

Use undo import evpn mac-ip to disable the device from redistributing received MAC/IP advertisement routes that contain ARP or ND information into a BGP unicast routing table.

Syntax

import evpn mac-ip

undo import evpn mac-ip

Default

MAC/IP advertisement routes that contain ARP or ND information are not redistributed into any BGP unicast routing table.

Views

BGP IPv4 unicast address family view

BGP IPv6 unicast address family view

BGP-VPN IPv4 unicast address family view

BGP-VPN IPv6 unicast address family view

Predefined user roles

network-admin

Usage guidelines

This command enables the device to redistribute received MAC/IP advertisement routes that contain ARP or ND information into a BGP unicast routing table.

· If you use this command in BGP IPv4 or IPv6 unicast address family view, the device will redistribute the routes into the BGP IPv4 or IPv6 unicast routing table. In addition, the device will advertise the routes to the local site.

· If you use this command in BGP-VPN IPv4 or IPv6 unicast address family view, the device will redistribute the routes into the BGP-VPN IPv4 or IPv6 unicast routing table of the corresponding VPN instance. To advertise the routes to the local site, you must configure the advertise l2vpn evpn command.

Examples

# Redistribute received MAC/IP advertisement routes into the BGP-VPN IPv4 unicast routing table of VPN instance vpna.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp-default] ip vpn-instance vpna

[Sysname-bgp-default-vpna] address-family ipv4

[Sysname-bgp-default-ipv4-vpna] import evpn mac-ip

Related commands

advertise l2vpn evpn

import route-policy

Use import route-policy to apply an import routing policy to EVPN on a VPN instance.

Use undo import route-policy to restore the default.

Syntax

import route-policy route-policy

undo import route-policy

Default

No import routing policy is applied to EVPN on a VPN instance. The VPN instance accepts a route when the export route targets of the route match local import route targets.

Views

VPN instance EVPN view

Predefined user roles

network-admin

Parameters

route-policy: Specifies a routing policy by its name, a case-sensitive string of 1 to 63 characters.

Usage guidelines

You can specify an import routing policy to filter received routes or modify their route attributes for EVPN.

If you execute this command multiple times, the most recent configuration takes effect.

EVPN can use an import routing policy specified in VPN instance view or in VPN instance EVPN view. Import routing policy configuration in VPN instance EVPN view takes precedence over that in VPN instance view.

Examples

# Apply import routing policy poly-1 to EVPN on VPN instance vpn1.

<Sysname> system-view

[Sysname] ip vpn-instance vpn1

[Sysname-vpn-instance-vpn1] address-family evpn

[Sysname-vpn-evpn-vpn1] import route-policy poly-1

Related commands

route-policy (Layer 3—IP Routing Command Reference)

ip forwarding-conversational-learning

Use ip forwarding-conversational-learning to enable conversational learning for host route FIB entries.

Use undo ip forwarding-conversational-learning to disable conversational learning for host route FIB entries.

Syntax

ip forwarding-conversational-learning [ aging aging-time ]

undo ip forwarding-conversational-learning

Default

Conversational learning is disabled for host route FIB entries.

Views

System view

Predefined user roles

network-admin

Parameters

aging aging-time: Specifies an aging timer in minutes for host route FIB entries, in the range of 60 to 1440. The default value is 60.

Usage guidelines

Use this command only on an EVPN network.

By default, the device issues a host route FIB entry to the hardware after the entry is generated. This feature enables the device to issue a host route FIB entry to the hardware only when the entry is required for packet forwarding. This feature saves hardware resources on the device.

Set an appropriate aging timer for host route FIB entries according to your network. A much longer or shorter aging timer will degrade the device performance.

· If the aging timer is too long, the device will save many outdated host route FIB entries and fail to accommodate the most recent network changes. These entries cannot be used for correct packet forwarding and exhaust FIB resources.

· If the aging timer is too short, the device will delete the valid host route FIB entries that can still be effective for packet forwarding. As a result, FIB entry flapping will occur, and the device performance will be affected.

Examples

# Enable conversational learning for host route FIB entries.

<Sysname> system-view

[Sysname] ip forwarding-conversational-learning

ip public-instance

Use ip public-instance to create the public instance and enter its view, or enter the view of the existing public instance.

Use undo ip public-instance to delete the public instance.

Syntax

ip public-instance

undo ip public-instance

Default

The public instance does not exist.

Views

System view

Predefined user roles

network-admin

Usage guidelines

A distributed EVPN gateway uses the public instance to perform Layer 3 forwarding for the public network and to enable communication between private and public networks. The public instance is similar to a VPN instance. A distributed EVPN gateway processes traffic of the public instance in the same way it does for a VPN instance.

Examples

# Create the public instance and enter its view.

<Sysname> system-view

[Sysname] ip public-instance

[Sysname-public-instance]

ip-prefix-route generate disable

Use ip-prefix-route generate disable to disable generation of IP prefix advertisement routes for the subnets of a VSI interface.

Use undo ip-prefix-route generate disable to enable generation of IP prefix advertisement routes for the subnets of a VSI interface.

Syntax

ip-prefix-route generate disable

undo ip-prefix-route generate disable

Default

The device only generates MAC/IP advertisement routes for a VSI interface that provides centralized VXLAN IP gateway service. The device generates IP prefix advertisement routes for the subnets of a VSI interface that provides distributed VXLAN IP gateway service.

Views

VSI interface view

Predefined user roles

network-admin

Usage guidelines

This command takes effect only on a VSI interface that provides distributed VXLAN IP gateway service (configured by using the distributed-gateway local command). It does not take effect on VSI interfaces that provide centralized VXLAN IP gateway service.

Examples

# Disable generation of IP prefix advertisement routes for the subnets of VSI-interface 1.

<Sysname> system-view

[Sysname] interface vsi-interface 1

[Sysname-Vsi-interface1] ip-prefix-route generate disable

ipv6 forwarding-conversational-learning

Use ipv6 forwarding-conversational-learning to enable conversational learning for IPv6 host route FIB entries.

Use undo ipv6 forwarding-conversational-learning to disable conversational learning for IPv6 host route FIB entries.

Syntax

ipv6 forwarding-conversational-learning [ aging aging-time ]

undo ipv6 forwarding-conversational-learning

Default

Conversational learning is disabled for IPv6 host route FIB entries.

Views

System view

Predefined user roles

network-admin

Parameters

aging aging-time: Sets an aging timer in minutes for IPv6 host route FIB entries, in the range of 60 to 1440. The default value is 60.

Usage guidelines

Use this command only on an EVPN network.

By default, the device issues an IPv6 host route FIB entry to the hardware after the entry is generated. This feature enables the device to issue an IPv6 host route FIB entry to the hardware only when the entry is required for packet forwarding. This feature saves hardware resources on the device.

Set an appropriate aging timer for IPv6 host route FIB entries according to your network. A much longer or shorter aging timer will degrade the device performance.

· If the aging timer is too long, the device will save many outdated IPv6 host route FIB entries and fail to accommodate the most recent network changes. These entries cannot be used for correct packet forwarding and exhaust FIB resources.

· If the aging timer is too short, the device will delete the valid IPv6 host route FIB entries that can still be effective for packet forwarding. As a result, FIB entry flapping will occur, and the device performance will be affected.

Examples

# Enable conversational learning for IPv6 host route FIB entries and set the entry aging timer to 80 minutes.

<Sysname> system-view

[Sysname] ipv6 forwarding-conversational-learning aging 80

l3-vni

Use l3-vni to configure an L3 VXLAN ID for a VSI interface or for the public instance.

Use undo l3-vni to remove the L3 VXLAN ID for a VSI interface or for the public instance.

Syntax

l3-vni vxlan-id

undo l3-vni

Default

No L3 VXLAN ID is configured for a VSI interface or for the public instance.

Views

VSI interface view

Public instance view

Predefined user roles

network-admin

Parameters

vxlan-id: Specifies a VXLAN ID in the range of 0 to 16777215.

Usage guidelines

On distributed EVPN gateways, you must configure L3 VXLAN IDs for the gateways to differentiate traffic of different VPN instances.

To forward Layer 3 traffic of a VPN instance, you must assign an L3 VXLAN ID to the VSI interface of the VPN instance. To forward Layer 3 traffic of the public network, you must assign the same L3 VXLAN ID to the public instance and the VSI interface of the public instance.

To modify the L3 VXLAN ID for the public instance, you must first delete the original L3 VXLAN ID.

The L3 VXLAN ID specified by using this command cannot be the same as any VXLAN ID specified by using the mapping vni command.

Examples

# Configure the L3 VXLAN ID as 1000 for VSI-interface 100.

<Sysname> system-view

[Sysname] interface vsi-interface 100

[Sysname-Vsi-interface100] l3-vni 1000

mac-address forwarding-conversational-learning

Use mac-address forwarding-conversational-learning to enable conversational learning for remote MAC address entries.

Use undo mac-address forwarding-conversational-learning to disable conversational learning for remote MAC address entries.

Syntax

mac-address forwarding-conversational-learning

undo mac-address forwarding-conversational-learning

Default

Conversational learning is disabled for remote MAC address entries.

Views

System view

Predefined user roles

network-admin

Usage guidelines

Use this command only on an EVPN network.

By default, the device issues a remote MAC address entry to the hardware after the remote MAC address is advertised to the local site by BGP EVPN routes. This feature enables the device to issue a remote MAC address entry to the hardware only when the entry is required for packet forwarding. This feature saves hardware resources on the device.

With this feature enabled, the device generates a blackhole MAC address entry for an unknown MAC address if receiving 50 frames destined for that MAC address within the MAC aging time. For more information about the MAC aging time and blackhole MAC address entries, see MAC address table configuration in Layer 2—LAN Switching Configuration Guide.

Examples

# Enable conversational learning for remote MAC address entries.

<Sysname> system-view

[Sysname] mac-address forwarding-conversational-learning

mac-advertising disable

Use mac-advertising disable to disable MAC address advertisement and withdraw advertised MAC addresses.

Use undo mac-advertising disable to restore the default.

Syntax

mac-advertising disable

undo mac-advertising disable

Default

MAC address advertisement is enabled.

Views

EVPN instance view

Predefined user roles

network-admin

Usage guidelines

The MAC information and ARP information advertised by the VTEP overlap. To avoid duplication, use this command to disable MAC address advertisement and withdraw the MAC addresses advertised to remote VTEPs.

Examples

# Disable MAC address advertisement and withdraw advertised MAC addresses for an EVPN instance.

<Sysname> system-view

[Sysname] vsi aaa

[Sysname-vsi-aaa] evpn encapsulation vxlan

[Sysname-vsi-aaa-evpn-vxlan] mac-advertising disable

mapping vni

Use mapping vni to map a local VXLAN to a remote VXLAN.

Use undo mapping vni to restore the default.

Syntax

mapping vni vxlan-id

undo mapping vni

Default

A local VXLAN is not mapped to any remote VXLAN.

Views

EVPN instance view

Predefined user roles

network-admin

Parameters

vxlan-id: Specifies a remote VXLAN ID in the range of 0 to 16777215.

Usage guidelines

The VXLAN mapping feature provides Layer 2 connectivity for a tenant subnet that uses different VXLAN IDs in multiple data centers.

VXLAN mapping includes the following types:

· Non-intermediate VXLAN mapping—When two data centers use different VXLAN IDs for a subnet, map the local VXLAN to the remote VXLAN on the ED of one data center. For example, for VXLAN 10 of data center 1 to communicate with VXLAN 20 of data center 2, map VXLAN 10 to VXLAN 20 on the ED of data center 1.

· Intermediate VXLAN mapping—When multiple data centers use different VXLAN IDs for a subnet, map the VXLANs to an intermediate VXLAN on all EDs. For example, data center 1 uses VXLAN 10, data center 2 uses VXLAN 20, and data center 3 uses VXLAN 30. To provide connectivity for the VXLANs, map them to intermediate VXLAN 500 on EDs of the data centers. You must use intermediate VXLAN mapping if more than two data centers use different VXLAN IDs. The intermediate VXLAN can be used only for VXLAN mapping, and it cannot be used for common VXLAN services.

You must create mapped remote VXLANs on the device, create an EVPN instance for each remote VXLAN, and configure RD and route target settings for the EVPN instances.

The mapped remote VXLAN ID cannot be any L3 VXLAN ID specified by using the l3-vni command or the reserved VXLAN ID specified by using the reserved vxlan command.

Examples

# Map local VXLAN 100 to remote VXLAN 200.

<Sysname> system-view

[Sysname] vsi aaa

[Sysname-vsi-aaa] vxlan 100

[Sysname-vsi-aaa-vxlan-100] quit

[Sysname-vsi-aaa] evpn encapsulation vxlan

[Sysname-vsi-aaa-evpn-vxlan] mapping vni 200

Related commands

reserved vxlan (VXLAN Command Reference)

nd mac-learning disable

Use nd mac-learning disable to disable an EVPN instance from learning MAC addresses from ND information.

Use undo nd mac-learning disable to restore the default.

Syntax

nd mac-learning disable

undo nd mac-learning disable

Default

An EVPN instance learns MAC addresses from ND information.

Views

EVPN instance view

Predefined user roles

network-admin

Usage guidelines

The MAC information and ND information advertised by a remote VTEP overlap. To avoid duplication, use this command to disable the learning of MAC addresses from ND information. EVPN will learn remote MAC addresses only from the MAC information advertised from remote sites.

Examples

# Disable an EVPN instance from learning MAC addresses from ND information.

<Sysname> system-view

[Sysname] vsi aaa

[Sysname-vsi-aaa] evpn encapsulation vxlan

[Sysname-vsi-aaa-evpn-vxlan] nd mac-learning disable

peer advertise evpn-route suppress

Use peer advertise evpn-route suppress to suppress the advertisement of specific BGP EVPN routes to a peer or peer group.

Use undo peer advertise evpn-route suppress to restore the default.

Syntax

peer { group-name | ipv4-address [ mask-length ] } advertise evpn-route suppress { ip-prefix | mac-ip }

undo peer { group-name | ipv4-address [ mask-length ] } advertise evpn-route suppress { ip-prefix | mac-ip }

Default

Advertisement of BGP EVPN routes is not suppressed.

Views

BGP EVPN address family view

Predefined user roles

network-admin

Parameters

group-name: Specifies a peer group by its name, a case-sensitive string of 1 to 47 characters. The peer group must exist.

ipv4-address: Specifies a peer by its IPv4 address. The peer must exist.

mask-length: Specifies a mask length in the range of 0 to 32. To specify a subnet, you must specify both the ipv4-address and mask-length arguments.

ip-prefix: Suppresses IP prefix advertisement routes.

mac-ip: Suppresses MAC/IP advertisement routes.

Usage guidelines

To reduce the number of BGP EVPN routes on EDs of an EVPN-DCI network, suppress the advertisement of specific BGP EVPN routes on the EDs.

If two VSI interfaces on EVPN gateways of different data centers use the same IP address, do not suppress the advertisement of MAC/IP advertisement routes on the EDs of the data centers. If you suppress the advertisement of these routes, the EDs cannot communicate with each other.

Examples

# Suppress the IP prefix advertisement routes advertised to peer 1.1.1.1.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp-default] address-family l2vpn evpn

[Sysname-bgp-default-evpn] peer 1.1.1.1 advertise evpn-route suppress ip-prefix

peer default-gateway no-advertise

Use peer default-gateway no-advertise to remove the default-gateway extended community attribute from the EVPN gateway routes advertised to a peer or peer group.

Use undo peer default-gateway no-advertise to restore the default.

Syntax

peer { group-name | ipv4-address [ mask-length ] } default-gateway no-advertise

undo peer { group-name | ipv4-address [ mask-length ] } default-gateway no-advertise

Default

EVPN gateway routes advertised to peers and peer groups contain the default-gateway extended community attribute.

Views

BGP EVPN address family view

Predefined user roles

network-admin

Parameters

group-name: Specifies a peer group by its name, a case-sensitive string of 1 to 47 characters. The peer group must exist.

ipv4-address: Specifies a peer by its IPv4 address. The peer must exist.

mask-length: Specifies a mask length in the range of 0 to 32. To specify a subnet, you must specify both the ipv4-address and mask-length arguments.

Usage guidelines

An EVPN gateway route is the route for the IP address of a VSI interface on an EVPN gateway. By default, the EVPN gateway routes advertised by an EVPN gateway contain the default-gateway extended community attribute. The EVPN gateway routes with that attribute cannot be used as ECMP routes. You can use this command to remove the default-gateway extended community attribute from EVPN gateway routes for the routes to be used for load sharing.

Examples

# Remove the default-gateway extended community attribute from the EVPN gateway routes advertised to peer 1.1.1.1.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp-default] address-family l2vpn evpn

[Sysname-bgp-default-evpn] peer 1.1.1.1 default-gateway no-advertise

peer next-hop-invariable

Use peer next-hop-invariable to configure the device to not change the next hop of routes advertised to an EBGP peer or peer group.

Use undo peer next-hop-invariable to configure the device to use its address as the next hop of routes advertised to an EBGP peer or peer group.

Syntax

peer { group-name | ipv4-address [ mask-length ] } next-hop-invariable

undo peer { group-name | ipv4-address [ mask-length ] } next-hop-invariable

Default

The device uses its address as the next hop of routes advertised to EBGP peers or peer groups.

Views

BGP EVPN address family view

Predefined user roles

network-admin

Parameters

group-name: Specifies a peer group by its name, a case-sensitive string of 1 to 47 characters.

ipv4-address: Specifies a peer by its IPv4 address.

mask-length: Specifies a mask length in the range of 0 to 32. To specify a subnet, you must specify both the ipv4-address and mask-length arguments.

Usage guidelines

This command is exclusive with the peer next-hop-local command.

The next hop in BGP EVPN routes is the IP address of the originating VTEP. By default, the device replaces the next hop of IBGP routes with its address when advertising the routes to an EBGP peer. If the device is a transport network device, it will modify the next hop of BGP EVPN routes. For VTEPs to learn one another's IP address, you must configure the device to not change the next hop of routes advertised to EBGP peers.

Examples

# Configure the device to not change the next hop of routes advertised to EBGP peer 1.1.1.1.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp-default] address-family l2vpn evpn

[Sysname-bgp-default-evpn] peer 1.1.1.1 next-hop-invariable

Related commands

peer next-hop-local (Layer 3—IP Routing Command Reference)

peer re-originated

Use peer re-originated to replace the L3 VXLAN ID and RD of IP prefix advertisement routes.

Use undo peer re-originated to restore the default.

Syntax

peer { group-name | ipv4-address [ mask-length ] } re-originated

undo peer { group-name | ipv4-address [ mask-length ] } re-originated

Default

The device does not modify the L3 VXLAN ID or RD of the IP prefix advertisement routes that are received from peers or peer groups.

Views

BGP EVPN address family view

Predefined user roles

network-admin

Parameters

group-name: Specifies a peer group by its name, a case-sensitive string of 1 to 47 characters. The peer group must exist.

ipv4-address: Specifies a peer by its IPv4 address. The peer must exist.

mask-length: Specifies a mask length in the range of 0 to 32. To specify a subnet, you must specify both the ipv4-address and mask-length arguments.

Usage guidelines

In an EVPN-DCI network, use this command to enable communication between data centers that use different L3 VXLAN IDs or hide the L3 VXLAN ID of a data center. After you execute this command on an ED, the ED performs the following operations after receiving IP prefix advertisement routes:

1. Matches the route targets of the routes with the import route targets of local VPN instances.

2. Replaces the L3 VXLAN ID and RD of the routes with the L3 VXLAN ID and RD of the matching local VPN instance.

3. Advertises the routes to a VTEP or remote ED.

After you execute this command, an ED advertises only IP prefix advertisement routes with the replaced L3 VXLAN ID and RD. The IP prefix advertisement routes with the original L3 VXLAN ID and RD are not advertised.

If the RD of a received IP prefix advertisement route is identical to the RD of the matching local VPN instance, an ED does not replace the L3 VXLAN ID of the route or regenerate the route. As a result, the ED does not advertise the route. As a best practice, assign unique RDs to VPN instances on different EVPN gateways and EDs when you use this command.

Examples

# Replace the L3 VXLAN ID and RD of IP prefix advertisement routes.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp-default] address-family l2vpn evpn

[Sysname-bgp-default-evpn] peer 1.1.1.1 re-originated

peer router-mac-local

Use peer router-mac-local to enable route router MAC replacement for a peer or peer group.

Use undo peer router-mac-local to cancel route router MAC replacement configuration for a peer or peer group.

Syntax

peer { group-name | ipv4-address [ mask-length ] } router-mac-local

undo peer { group-name | ipv4-address [ mask-length ] } router-mac-local

Default

The device does not modify the router MAC address of routes before advertising the routes.

Views

BGP EVPN address family view

Predefined user roles

network-admin

Parameters

group-name: Specifies a peer group by its name, a case-sensitive string of 1 to 47 characters. The peer group must exist.

ipv4-address: Specifies a peer by its IPv4 address. The peer must exist.

mask-length: Specifies a mask length in the range of 0 to 32. To specify a subnet, you must specify both the ipv4-address and mask-length arguments

Usage guidelines

This command enables an ED to use its router MAC address to replace the router MAC address of routes received from and advertised to a peer or peer group in the local data center. The router MAC replacement process is as follows:

· For routes received from the peer or peer group, the ED performs router MAC replacement and advertises the routes to remote EDs.

· For routes received from a remote data center, the ED performs router MAC replacement and advertises the routes to the peer or peer group.

Examples

# In BGP EVPN address family view, enable route router MAC replacement for peer 1.1.1.1.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp-default] address-family l2vpn evpn

[Sysname-bgp-default-evpn] peer 1.1.1.1 router-mac-local

policy vpn-target

Use policy vpn-target to enable route target filtering for BGP EVPN routes.

Use undo policy vpn-target to disable route target filtering for BGP EVPN routes.

Syntax

policy vpn-target

undo policy vpn-target

Default

Route target filtering is enabled for BGP EVPN routes.

Views

BGP EVPN address family view

Predefined user roles

network-admin

Usage guidelines

When route target filtering is enabled for BGP EVPN routes, the EVPN routing table accepts only BGP EVPN routes of which the export route targets match the local import route targets. If the device must save all BGP EVPN routes, use the undo policy vpn-target command to disable route target filtering for BGP EVPN routes.

Examples

# Disable route target filtering for BGP EVPN routes.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp-default] address-family l2vpn evpn

[Sysname-bgp-default-evpn] undo policy vpn-target

route-distinguisher (EVPN instance view)

Use route-distinguisher to configure an RD for an EVPN instance.

Use undo route-distinguisher to restore the default.

Syntax

route-distinguisher { route-distinguisher | auto [ router-id ] }

undo route-distinguisher

Default

No RD is configured for an EVPN instance.

Views

EVPN instance view

Predefined user roles

network-admin

Parameters

route-distinguisher: Specifies an RD, a string of 3 to 21 characters. The RD cannot be all zeros and can use one of the following formats:

· 16-bit AS number:32-bit user-defined number. For example, 101:3.

· 32-bit IP address:16-bit user-defined number. For example, 192.168.122.15:1.

· 32-bit AS number:16-bit user-defined number. For example, 65536:1. The AS number must be equal to or greater than 65536.

auto: Automatically generates an RD in the N:VXLAN ID format. The initial value of N is 1. If N:VXLAN ID is already in use, the system increases the value of N by 1 until the RD is available.

router-id: Automatically generates an RD based on the router ID in the Router ID:N format. The initial value of N is 1. If Router ID:N is already in use, the system increases the value of N by 1 until the RD is available. If you do not specify this keyword with the auto keyword, the system automatically generates an RD based on the VXLAN ID in the N:VXLAN ID format.

Usage guidelines

EVPN uses MP-BGP to advertise BGP EVPN routes for automatic VTEP discovery, MAC reachability information advertisement, and host route advertisement. MP-BGP uses the RD to differentiate BGP EVPN routes of different EVPN instances.

Examples

# Configure 22:1 as the RD of an EVPN instance.

<Sysname> system-view

[Sysname] vsi aaa

[Sysname-vsi-aaa] evpn encapsulation vxlan

[Sysname-vsi-aaa-evpn-vxlan] route-distinguisher 22:1

route-distinguisher (public instance view)

Use route-distinguisher to configure an RD for the public instance.

Use undo route-distinguisher to restore the default.

Syntax

route-distinguisher route-distinguisher

undo route-distinguisher

Default

No RD is configured for the public instance.

Views

Public instance view

Predefined user roles

network-admin

Parameters

route-distinguisher: Specifies an RD, a string of 3 to 21 characters. The RD can use one of the following formats:

· 16-bit AS number:32-bit user-defined number. For example, 101:3.

· 32-bit IP address:16-bit user-defined number. For example, 192.168.122.15:1.

· 32-bit AS number:16-bit user-defined number. For example, 65536:1. The AS number must be equal to or greater than 65536.

Usage guidelines

To modify the RD of the public instance, first execute the undo route-distinguisher command to remove the original RD.

Examples

# Configure 22:1 as the RD of the public instance.

<Sysname> system-view

[Sysname] ip public-instance

[Sysname-public-instance] route-distinguisher 22:1

rr-filter

Use rr-filter to create a route reflector (RR) reflection policy.

Use undo rr-filter to restore the default.

Syntax

rr-filter ext-comm-list-number

undo rr-filter

Default

An RR does not filter reflected BGP EVPN routes.

Views

BGP EVPN address family view

Predefined user roles

network-admin

Parameters

ext-comm-list-number: Specifies an extended community attribute list by its number in the range of 1 to 199.

Usage guidelines

This command enables an RR to reflect only received BGP EVPN routes that match the attributes in the specified extended community attribute list.

If a cluster contains multiple RRs, you can configure different reflection policies on the RRs for load sharing among the RRs.

For more information about the extended community attribute list, see Layer 3—IP Routing Configuration Guide.

Examples

# Configure a reflection policy for the device to reflect BGP EVPN routes that match extended community attribute list 10.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp-default] address-family l2vpn evpn

[Sysname-bgp-default-evpn] rr-filter 10

Related commands

ip extcommunity-list (Layer 3—IP Routing Command Reference)

vpn-route cross multipath

Use vpn-route cross multipath to enable ECMP VPN route redistribution.

Use undo vpn-route cross multipath to disable ECMP VPN route redistribution.

Syntax

vpn-route cross multipath

undo vpn-route cross multipath

Default

ECMP VPN route redistribution is disabled. If multiple routes have the same prefix and RD, BGP only imports the optimal route into the EVPN routing table.

Views

BGP EVPN address family view

Predefined user roles

network-admin

Usage guidelines

ECMP VPN route redistribution enables BGP to import all routes that have the same prefix and RD into the EVPN routing table.

Examples

# Enable ECMP VPN route redistribution.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp-default] address-family l2vpn evpn

[Sysname-bgp-default-evpn] vpn-route cross multipath

vpn-target

Use vpn-target to configure route targets for EVPN.

Use undo vpn-target to delete route targets for EVPN.

Syntax

In EVPN instance view:

vpn-target { vpn-target&<1-8> | auto } [ both | export-extcommunity | import-extcommunity ]

undo vpn-target { vpn-target&<1-8> | auto | all } [ both | export-extcommunity | import-extcommunity ]

VPN instance EVPN view, public instance view, public instance IPv4 address family view, public instance IPv6 address family view, or public instance EVPN view:

vpn-target vpn-target&<1-8> [ both | export-extcommunity | import-extcommunity ]

undo vpn-target { all | vpn-target&<1-8> [ both | export-extcommunity | import-extcommunity ] }

Default

EVPN does not have route targets.

Views

EVPN instance view

VPN instance EVPN view

Public instance view

Public instance EVPN view

Public instance IPv4 address family view

Public instance IPv6 address family view

Predefined user roles

network-admin

Parameters

vpn-target&<1-8>: Specifies a space-separated list of up to eight route targets. Each route target is a string of 3 to 21 characters in one of the following formats:

· 16-bit AS number:32-bit user-defined number. For example, 101:3.

· 32-bit IP address:16-bit user-defined number. For example, 192.168.122.15:1.

· 32-bit AS number:16-bit user-defined number. For example, 65536:1. The AS number must be equal to or greater than 65536.

auto: Automatically generates a route target in the format of BGP AS number:VXLAN ID.

both: Uses the specified route targets as both import and export targets. If you do not specify the both, export-extcommunity, or import-extcommunity keyword, the both keyword applies.

export-extcommunity: Uses the specified route targets as export targets.

import-extcommunity: Uses the specified route targets as import targets.

all: Specifies all route targets.

Usage guidelines

EVPN uses MP-BGP to advertise BGP EVPN routes for automatic VTEP discovery, MAC reachability information advertisement, and host route advertisement. MP-BGP uses route targets to control the advertisement and acceptance of BGP EVPN routes.

A VTEP sets the export targets for BGP EVPN routes before advertising the routes to remote VTEPs. The VTEP checks the export targets of BGP EVPN routes from remote VTEPs and imports only BGP EVPN routes of which the export targets match the local import targets.

If you execute this command multiple times, all configured route targets take effect.

Examples

# Configure import route targets 10:1, 100:1, and 1000:1 for an EVPN instance.

<Sysname> system-view

[Sysname] vsi aaa

[Sysname-vsi-aaa] evpn encapsulation vxlan

[Sysname-vsi-aaa-evpn-vxlan] vpn-target 10:1 100:1 1000:1 import-extcommunity

19-EVPN Command Reference

EVPN commands

address-family evpn (VPN instance view)

evpn encapsulation

nd mac-learning disable

route-distinguisher (public instance view)

rr-filter

Intelligent Terminal Products

Product Support Services

Technical Service Solutions

Resource Center

Policy

Online Help

Become a Partner

Partner Policy & Program

Global Learning

Partner Sales Resources

Service Business

News & Events

Contact Us