The monitoring diagnostic tests vary in enabling status. To view the enabling status of monitoring diagnostic tests, execute the display diagnostic content command.

Views

System view

Predefined user roles

network-admin

mdc-admin

Parameters

chassis chassis-number: Specifies an IRF member device by its member ID. (In IRF mode.)

slot slot-number-list: Specifies a space-separated list of up to seven slot number items. An item specifies a card by its slot number or specifies a range of cards in the form of start-slot-number to end-slot-number. The end slot number must be equal to or greater than the start slot number.

test test-name: Specifies a test by its name, a case-sensitive character string. You can use the test ? command to verify the value range of the test name. If you do not specify this option, the command enables all monitoring diagnostic tests.

Usage guidelines

Monitoring diagnostics enable the system to periodically run diagnostic tests to detect hardware faults and record test results. Monitoring diagnostics execute only non-disruptive tests.

Disruptive diagnostic tests that are being executed affect device operation or even disable certain functions, but non-disruptive diagnostic tests do not.

The system automatically executes enabled monitoring diagnostic tests after the device starts. Use the diagnostic monitor enable command to enable diagnostic tests that are disabled by default.

Examples

# (In standalone mode.) Enable test BoardStatusMonitor on the specified slot.

<Sysname> system-view

[Sysname] diagnostic monitor enable slot 1 test BoardStatusMonitor

Related commands

diagnostic monitor interval

Use diagnostic monitor interval to configure an execution interval for monitoring diagnostic tests.

Use undo diagnostic monitor interval to restore the default.

Syntax

In standalone mode:

diagnostic monitor interval slot slot-number-list [ test test-name ] time interval

undo diagnostic monitor interval slot slot-number-list [ test test-name ]

In IRF mode:

diagnostic monitor interval chassis chassis-number slot slot-number-list [ test test-name ] time interval

undo diagnostic monitor interval chassis chassis-number slot slot-number-list [ test test-name ]

Default

The execution interval varies by monitoring diagnostic test. To display the execution interval of a monitoring diagnostic test, execute the display diagnostic content command.

Views

System view

Predefined user roles

network-admin

mdc-admin

Parameters

chassis chassis-number: Specifies an IRF member device by its member ID. (In IRF mode.)

interval: Sets an execution interval in the form of hh:mm:ss. The value range for the hh argument is 0 to 23. The value range for the mm and ss arguments is both 0 to 59. If you specify only the hh argument, you can omit the mm and ss segments. If you specify only the hh and mm arguments, you can omit the ss segment. For example, to specify 01:00:00, you can enter 1.

Usage guidelines

Use this command to configure the interval at which the system automatically executes enabled monitoring diagnostic tests.

The configured interval cannot be smaller than the minimum execution interval of the tests. Use the display diagnostic content verbose command to view the minimum execution interval of the tests.

Examples

# (In standalone mode.) Set the execution interval to 1 minute for test BoardStatusMonitor on the specified slot.

<Sysname> system-view.

[Sysname] diagnostic monitor interval slot 1 test BoardStatusMonitor time 00:01:00

Related commands

diagnostic monitor enable

display diagnostic content

diagnostic simulation

Use diagnostic simulation to simulate diagnostic tests.

Use undo diagnostic simulation to restore the default.

Syntax

In standalone mode:

diagnostic simulation slot slot-number-list test test-name { failure | random-failure | success }

undo diagnostic simulation slot slot-number-list test test-name

In IRF mode:

diagnostic simulation chassis chassis-number slot slot-number-list test test-name { failure | random-failure | success }

undo diagnostic simulation chassis chassis-number slot slot-number-list test test-name

Default

All diagnostic tests are executed instead of simulated.

Views

User view

Predefined user roles

network-admin

mdc-admin

Parameters

chassis chassis-number: Specifies an IRF member device by its member ID. (In IRF mode.)

test-name: Specifies a test by its name, a case-sensitive character string. You can use the test ? command to verify the value range of the test name.

failure: Configures the system to generate failure results.

random-failure: Configures the system to randomly generate results.

success: Configures the system to generate success results.

Usage guidelines

Test simulation is used to verify GOLD frame functionality. After you execute this command, the system simulates the specified test if the execution requirements for the test are met. The test is not actually executed and does not trigger hardware correcting actions.

Examples

# (In standalone mode.) Simulate test BoardStatusMonitor as failed on the specified slot.

<Sysname> diagnostic simulation slot 1 test BoardStatusMonitor failure

Related commands

display diagnostic simulation

display diagnostic content

Use display diagnostic content to display information about diagnostic tests.

Syntax

In standalone mode:

display diagnostic content [ slot slot-number ] [ verbose ]

In IRF mode:

display diagnostic content [ chassis chassis-number [ slot slot-number ] ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

slot slot-number: Specifies a card by its slot number. If you do not specify this option, the command applies to all cards. (In standalone mode.)

chassis chassis-number: Specifies an IRF member device by its member ID. If you do not specify a member device, the command applies to all member devices. (In IRF mode.)

slot slot-number: Specifies a card by its slot number. If you do not specify a card, the command applies to all cards. (In IRF mode.)

verbose: Displays detailed information about diagnostic tests. If you do not specify this keyword, the command displays brief information about the diagnostic tests.

Examples

# (In standalone mode.) Display brief information about all diagnostic tests on the specified slot.

<Sysname> display diagnostic content slot 1

Diagnostic test suite attributes:

#B/*: Bootup test/NA

#O/*: Ondemand test/NA

#M/*: Monitoring test/NA

#D/*: Disruptive test/Non-disruptive test

#P/*: Per port test/NA

#A/I/*: Monitoring test is active/Monitoring test is inactive/NA

Slot 1:

Name Attributes Interval

IPCMonitor **M*PA 00:01:00

BoardStatusMonitor **M*PA 01:00:00

TaskMonitor **M*PA 00:00:10

PortMonitor **M*PA 00:00:10

ComponentMonitor **M*PA 00:00:30

# (In standalone mode.) Display detailed information about all diagnostic tests on the specified slot.

<Sysname> display diagnostic content slot 1 verbose

Diagnostic test suite attributes:

#B/*: Bootup test/NA

#O/*: Ondemand test/NA

#M/*: Monitoring test/NA

#D/*: Disruptive test/Non-disruptive test

#P/*: Per port test/NA

#A/I/*: Monitoring test is active/Monitoring test is inactive/NA

Slot 1:

Test name : IPCMonitor

Test attributes : **M*PA

Test interval : 00:01:00

Min interval : 00:01:00

Correct-action : -NA-

Description : A Real-time test, enabled by default that checks ipc between

switch units.

Exec : -NA-

Test name : BoardStatusMonitor

Test attributes : **M*PA

Test interval : 01:00:00

Min interval : 00:00:06

Correct-action : -NA-

Description : A Real-time test, enabled by default that checks board status

between local master and other local boards.

Exec : -NA-

Test name : TaskMonitor

Test attributes : **M*PA

Test interval : 00:00:10

Min interval : 00:00:10

Correct-action : -NA-

Description : A Real-time test, enabled by default that checks the important

tasks.

Exec : -NA-

Test name : PortMonitor

Test attributes : **M*PA

Test interval : 00:00:10

Min interval : 00:00:10

Correct-action : -NA-

Description : A Real-time test, enabled by default that checks port status

for each inner port.

Exec : -NA-

Test name : ComponentMonitor

Test attributes : **M*PA

Test interval : 00:00:30

Min interval : 00:00:10

Correct-action : -NA-

Description : A Real-time test, enabled by default that checks component status.

Exec : -NA-

Table 1 Command output

Field	Description
B/*	(This field is not supported in the current software version.)Boot-up/Not boot-up.
O/*	(This field is not supported in the current software version.) On-demand/Not on-demand.
M/*	Monitoring/Not monitoring.
D/*	(This field is not supported in the current software version.) Disruptive/Non-disruptive.
P/*	Port-related/Not port-related.
A/I/*	Active and monitoring/Inactive and monitoring/Not monitoring.
Test name	Name of the diagnostic test.
Test attributes	Attributes of the diagnostic test. The characters from left to right indicate whether or not the test is boot-up, on-demand, monitoring, disruptive, port-related, or active. The asterisks (*) indicate that the test does not have the corresponding attributes.
Test interval	Execution interval for the test. If the execution interval for the test is not set, –NA–is displayed.
Min interval	Minimum execution interval for the test. If the test does not have a minimum execution interval, –NA–is displayed.
Correct-action	Correcting action triggered by failure of the test.
Description	Description for the test.

‌

display diagnostic event-log

Use display diagnostic event-log to display GOLD log entries.

Syntax

display diagnostic event-log [ error | info ]

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

error: Displays all error log entries.

info: Displays all log entries except error log entries.

Usage guidelines

If you do not specify the error and info keywords, the command displays all GOLD log entries.

The system records information about test execution in the form of logs. A log entry contains test name, execution time, test result, and failure cause. Log entries are generated for every execution. To reduce the burden of the information center, GOLD logs are not sent to the information center.

(In standalone mode.) GOLD logs are cleared when the device restarts or when an active/standby MPU switchover occurs.

(In IRF mode.) GOLD logs are cleared when the device restarts or when a global active/standby MPU switchover occurs.

Examples

# (In standalone mode.) Display all GOLD log entries.

<Sysname> display diagnostic event-log

Event: E_INFO, Wed Jan 7 11:39:53:314 2014, -Slot=1 TestName->IPCMonitor, Event_INFO: Result->Success.

display diagnostic result

Use display diagnostic result to display test results.

Syntax

In standalone mode:

display diagnostic result [ slot slot-number [ test test-name ] ] [ verbose ]

In IRF mode:

display diagnostic result [ chassis chassis-number [ slot slot-number [ test test-name ] ] ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

slot slot-number: Specifies a card by its slot number. If you do not specify this option, the command applies to all cards. (In standalone mode.)

chassis chassis-number: Specifies an IRF member device by its member ID. If you do not specify a member device, the command applies to all member devices. (In IRF mode.)

slot slot-number: Specifies a card by its slot number. If you do not specify a card, the command applies to all cards. (In IRF mode.)

verbose: Displays detailed test results for diagnostic tests that are enabled or executed. (Statistics are not included.) If you do not specify this parameter, the command displays brief test results for the diagnostic tests.

Examples

# (In standalone mode.) Display brief test results for all diagnostic tests on the specified slot.

<Sysname> display diagnostic result slot 1

Slot 1:

Name Run count Failure count Last result

IPCMonitor 51 0 Success

BoardStatusMonitor 386 0 Success

TaskMonitor 310 0 Success

PortMonitor 310 0 Success

ComponentMonitor 103 0 Success

# (In standalone mode.) Display detailed test results for all diagnostic tests.

<Sysname> display diagnostic result verbose

Slot 1:

Test name : IPCMonitor

Total run count : 52

Total failure count : 0

Consecutive failure count: 0

Last execution time : Fri Nov 21 23:13:25 2014

First failure time : -NA-

Last failure time : -NA-

Last pass time : Fri Nov 21 23:13:25 2014

Last execution result : Success

Last failure reason : -NA-

Next execution time : Fri Nov 21 23:14:25 2014

ipc link status : Normal

Test name : BoardStatusMonitor

Total run count : 386

Total failure count : 0

Consecutive failure count: 0

Last execution time : Fri Nov 21 23:00:01 2014

First failure time : -NA-

Last failure time : -NA-

Last pass time : Fri Nov 21 23:00:01 2014

Last execution result : Success

Last failure reason : -NA-

Next execution time : Sat Nov 22 00:00:07 2014

Slot check status : Normal

Test name : TaskMonitor

Total run count : 313

Total failure count : 0

Consecutive failure count: 0

Last execution time : Fri Nov 21 23:13:35 2014

First failure time : -NA-

Last failure time : -NA-

Last pass time : Fri Nov 21 23:13:35 2014

Last execution result : Success

Last failure reason : -NA-

Next execution time : Fri Nov 21 23:13:45 2014

Task check status : Normal

Test name : PortMonitor

Total run count : 313

Total failure count : 0

Consecutive failure count: 0

Last execution time : Fri Nov 21 23:13:35 2014

First failure time : -NA-

Last failure time : -NA-

Last pass time : Fri Nov 21 23:13:35 2014

Last execution result : Success

Last failure reason : -NA-

Next execution time : Fri Nov 21 23:13:45 2014

test result: pass

Test name : ComponentMonitor

Total run count : 104

Total failure count : 0

Consecutive failure count: 0

Last execution time : Fri Nov 21 23:13:25 2014

First failure time : -NA-

Last failure time : -NA-

Last pass time : Fri Nov 21 23:13:25 2014

Last execution result : Success

Last failure reason : -NA-

Next execution time : Fri Nov 21 23:13:55 2014

test result: pass

Table 2 Command output

Field	Description
Test name	Name of the test.
Total run count	Total number of executions.
Total failure count	Total number of failed tests.
Consecutive failure count	Number of consecutive failed tests.
Last execution time	Most recent execution time.
First failure time	First failed test time. If no failure occurs, –NA– is displayed.
Last failure time	Most recent failed test time. If no failure occurs, –NA– is displayed.
Last pass time	Most recent success test time. If no success occurs, –NA– is displayed.
Last execution result	Most recent test result.
Last failure reason	Cause for the most recent failed test. If the failed test is simulated, Simulated Test is displayed. If no failure occurs, –NA– is displayed.
Next execution time	Time for the next execution. The next execution time is the most recent execution time plus the execution interval.

‌

display diagnostic simulation

Use display diagnostic simulation to display configurations for simulated diagnostic tests.

Syntax

In standalone mode:

display diagnostic simulation [ slot slot-number ]

In IRF mode:

display diagnostic simulation [ chassis chassis-number [ slot slot-number ] ]

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

slot slot-number: Specifies a card by its slot number. If you do not specify this option, the command applies to all cards. (In standalone mode.)

chassis chassis-number: Specifies an IRF member device by its member ID. If you do not specify a member device, the command applies to all member devices. (In IRF mode.)

slot slot-number: Specifies a card by its slot number. If you do not specify a card, the command applies to all cards. (In IRF mode.)

Examples

# (In standalone mode.) Display configurations for all simulated diagnostic tests on the specified slot.

<Sysname> display diagnostic simulation slot 1

Slot 1:

Name Mode

BoardStatusMonitor failure

Related commands

diagnostic simulation

reset diagnostic event-log

Use reset diagnostic event-log to clear GOLD logs.

Syntax

reset diagnostic event-log

Views

User view

Predefined user roles

network-admin

mdc-admin

Examples

# Clear GOLD logs.

<Sysname> reset diagnostic event-log

Related commands

display diagnostic event-log

reset diagnostic result

Use reset diagnostic result to clear test results.

Syntax

In standalone mode:

reset diagnostic result [ slot slot-number [ test test-name ] ]

In IRF mode:

reset diagnostic result [ chassis chassis-number [ slot slot-number [ test test-name ] ] ]

Views

User view

Predefined user roles

network-admin

mdc-admin

Parameters

slot slot-number: Specifies a card by its slot number. If you do not specify this option, the command applies to all cards. (In standalone mode.)

chassis chassis-number: Specifies an IRF member device by its member ID. If you do not specify a member device, the command applies to all member devices. (In IRF mode.)

slot slot-number: Specifies a card by its slot number. If you do not specify a card, the command applies to all cards. (In IRF mode.)

Usage guidelines

This command does not clear the next execution time.

Examples

# (In standalone mode.) Clear test results for test BoardStatusMonitor on the specified slot.

<Sysname> reset diagnostic result slot 1 test BoardStatusMonitor

Related commands

display diagnostic result

12-Network Management and Monitoring Command Reference

GOLD commands

diagnostic event-log size

diagnostic monitor enable

diagnostic monitor interval

diagnostic simulation

display diagnostic content

display diagnostic event-log

display diagnostic result

display diagnostic simulation

reset diagnostic event-log

reset diagnostic result

Cloud & AI

InterConnect

Intelligent Computing

Security

SMB Products

Intelligent Terminal Products

Industry Solutions

Product Support Services

Technical Service Solutions

Resource Center

Policy

Online Help

Training & Certification

Become a Partner

Partner Resources

Partner Business Management

Company Information

News & Events

Online Exhibition Center

Contact Us