Contents

Policy-based routing commands· 1

apply next-hop· 1

display ip policy-based-route· 1

display ip policy-based-route interface· 2

display ip policy-based-route local 4

display ip policy-based-route setup· 5

if-match acl 6

ip local policy-based-route· 6

ip policy-based-route· 7

policy-based-route· 8

reset ip policy-based-route statistics· 9

 

Policy-based routing commands

apply next-hop

Use apply next-hop to set next hops.

Use undo apply next-hop to remove next hops.

Syntax

apply next-hop { ip-address [ direct ] [ track track-entry-number ] }&<1-2>

undo apply next-hop [ ip-address&<1-2> ]

Default

No next hop is set.

Views

Policy node view

Predefined user roles

network-admin

Parameters

ip-address: Specifies the IP address of the next hop.

direct: Specifies that the next hop must be directly connected to take effect.

track track-entry-number: Specifies a track entry by its number in the range of 1 to 1024.

&<1-2>: Indicates that the argument before it can be entered up to two times.

Usage guidelines

You can specify multiple next hops for backup in one command line or by executing this command multiple times.

With a next hop specified, the undo apply next-hop command removes the next hop.

Without any next hop specified, the undo apply next-hop command removes all next hops.

Examples

# Set a directly-connected next hop of 1.1.1.1.

<Sysname> system-view

[Sysname] policy-based-route aa permit node 11

[Sysname-pbr-aa-11] apply next-hop 1.1.1.1 direct

display ip policy-based-route

Use display ip policy-based-route to display PBR policy information.

Syntax

display ip policy-based-route [ policy policy-name ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

policy policy-name: Specifies a policy by its name, a case-sensitive string of 1 to 19 characters. If you do not specify a policy, this command displays information for all PBR policies.

Examples

# Display all policy information.

<Sysname> display ip policy-based-route

Policy name: aaa

  node 1 permit:

    if-match acl 2000

    apply next-hop 1.1.1.1

Table 1 Command output

Field	Description
node 1 permit	The match mode of Node 1 is permit.
if-match acl	Compares packets with the ACL.
apply next-hop	Specifies a next hop for permitted packets.

 

Related commands

policy-based-route

display ip policy-based-route interface

Use display ip policy-based-route interface to display interface PBR configuration and statistics.

Syntax

display ip policy-based-route interface interface-type interface-number [ slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

interface-type interface-number: Specifies an interface by its type and number.

slot slot-number: Specifies an IRF member device by its member ID. If you do not specify a member device, this command displays information on the master device.

Examples

# Display PBR configuration and statistics on VLAN-interface 2.

<Sysname> display ip policy-based-route interface vlan-interface 2

Policy based routing information for interface Vlan-interface2:

Policy name: aaa

  node 0 deny:

  Matched: 0

  node 1 permit:

    if-match acl 3999

  Matched: 0

  node 2 permit:

    if-match acl 2000

    apply next-hop 2.2.2.2

  Matched: 0

  node 5 permit:

    if-match acl 3101

    apply next-hop 1.1.1.1

    apply output-interface Vlan-interface3 track 1

    apply output-interface Vlan-interface4 track 2

  Matched: 0

Total matched: 0

<Sysname> display ip policy-based-route interface vlan-interface 2

Policy based routing information for interface Vlan-interface2:

Policy name: aaa

  node 0 deny:

  Matched: 0

  node 1 permit:

    if-match acl 3999

  Matched: 0

  node 2 permit:

    if-match acl 2000

    apply next-hop 2.2.2.2

    apply output-interface Vlan-interface3 track 1

    apply output-interface Vlan-interface4 track 2

  Matched: 0

  node 5 permit:

    if-match acl 3101

    apply next-hop 1.1.1.1

  Matched: 0

Total matched: 0

Table 2 Command output

Field	Description
Policy based routing information for interface XXXX(failed)	PBR configuration and statistics on the interface. NOTE: If you specify a slot number, this field displays failed in brackets for a policy that failed to be issued to the driver. The failure means that all node configurations in the PBR policy failed to be issued.
node 0 deny(not support) node 2 permit(no resource)	Match mode of the node, permit or deny. NOTE: If you specify a slot number, this field displays the cause in brackets for a node that does not take effect: ·         not support—The device does not support the match criteria configured on the node. ·         no resource—The node does not have sufficient resources (for example, ACLs).
if-match acl	Compares packets with the ACL.
apply next-hop	Specifies a next hop for permitted packets.
apply output-interface  track 1 (down)	Specifies an output interface and its associated track entry for permitted packets. This field displays the interface status in brackets. ·         up—The interface is up. ·         down—The interface is down at network layer. ·         inactive—The card that hosts the interface is not in position.
Matched: 0 (no statistics resource)	Number of successful matches on the node. NOTE: If you specify a slot number but the device does not have sufficient resources to collect statistics on the slot, this field displays no statistics resource in brackets.
Total matched	Total number of successful matches on all nodes.

 

Related commands

reset ip policy-based-route statistics

display ip policy-based-route local

Use display ip policy-based-route local to display local PBR configuration and statistics.

Syntax

display ip policy-based-route local [ slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

slot slot-number: Specifies an IRF member device by its member ID. If you do not specify a member device, this command displays local PBR configuration and statistics for the master device.

Examples

# Display local PBR configuration and statistics.

<Sysname> display ip policy-based-route local

Policy based routing information for local:

Policy name: aaa

  node 0 deny:

  Matched: 0

  node 1 permit:

    if-match acl 3999

  Matched: 0

  node 2 permit:

    if-match acl 2000

    apply next-hop 2.2.2.2

  Matched: 0

  node 5 permit:

    if-match acl 3101

    apply next-hop 1.1.1.1

  Matched: 0

Total matched: 0

Table 3 Command output

Field	Description
Policy based routing information for local	Local PBR configuration and statistics.
node 0 deny/node 2 permit	Match mode of the node: permit or deny.
if-match acl	Compares packets with the ACL.
apply next-hop	Specifies a next hop for permitted packets.
Matched: 0	Number of successful matches on the node.
Total matched	Total number of successful matches on all nodes.

 

Related commands

reset ip policy-based-route statistics

display ip policy-based-route setup

Use display ip policy-based-route setup to display PBR configuration.

Syntax

display ip policy-based-route setup

Views

Any view

Predefined user roles

network-admin

network-operator

Examples

# Display PBR configuration.

<Sysname> display ip policy-based-route setup

Policy name              Type     Interface

pr01                     Forward  Vlan-interface2

aaa                      Local    N/A

Table 4 Command output

Field	Description
Type	Type of the PBR: ·         Forward—Interface PBR. ·         Local—Local PBR.
Interface	Interface where the policy is applied.

 

Related commands

ip policy-based-route

if-match acl

Use if-match acl to set an ACL match criterion.

Use undo if-match acl to restore the default.

Syntax

if-match acl { acl-number | name acl-name }

undo if-match acl

Default

No ACL match criterion is set.

Views

Policy node view

Predefined user roles

network-admin

Parameters

acl-number: Specifies an ACL by its number in the range of 2000 to 2999 for a basic ACL, and in the range of 3000 to 3999 for an advanced ACL.

name acl-name: Specifies an ACL by its name, a case-insensitive string of 1 to 63 characters starting with letter a to z or A to Z. The ACL name cannot be all.

Examples

# Configure Node 11 of policy aa to permit the packets matching ACL 2011.

<Sysname> system-view

[Sysname] policy-based-route aa permit node 11

[Sysname-pbr-aa-11] if-match acl 2011

# Configure Node 11 of policy aa to permit the packets matching ACL aaa.

<Sysname> system-view

[Sysname] policy-based-route aa permit node 11

[Sysname-pbr-aa-11] if-match acl name aaa

ip local policy-based-route

Use ip local policy-based-route to specify a policy for local PBR.

Use undo ip local policy-based-route to restore the default.

Syntax

ip local policy-based-route policy-name

undo ip local policy-based-route

Default

No policy is referenced for local PBR.

Views

System view

Predefined user roles

network-admin

Parameters

policy-name: Specifies a policy by its name, a case-sensitive string of 1 to 19 characters. The specified policy must already exist.

Usage guidelines

Local PBR guides the forwarding of locally generated packets, such as ICMP packets generated by using the ping command.

Local PBR might affect local services, such as ping and Telnet. When you use local PBR, make sure you fully understand its impact on local services of the device.

You can specify only one policy for local PBR and must make sure the specified policy already exists.

Before you apply a new policy, you must first remove the current policy.

Examples

# Configure local PBR based on policy aaa.

<Sysname> system-view

[Sysname] ip local policy-based-route aaa

Related commands

display ip policy-based-route setup

ip policy-based-route apply

policy-based-route

ip policy-based-route

Use ip policy-based-route to specify a policy for interface PBR on an interface.

Use undo ip policy-based-route to restore the default.

Syntax

ip policy-based-route policy-name

undo ip policy-based-route

Default

No policy is applied to an interface.

Views

Interface view

Predefined user roles

network-admin

Parameters

policy-name: Specifies a policy by its name, a case-sensitive string of 1 to 19 characters. The specified policy must already exist.

Usage guidelines

You can apply only one policy to an interface. Before you apply a new policy, you must first remove the current policy from the interface.

Examples

# Apply policy aaa to VLAN-interface 2.

<Sysname> system-view

[Sysname] interface vlan-interface 2

[Sysname-Vlan-interface2] ip policy-based-route aaa

Related commands

display ip policy-based-route setup

ip policy-based-route apply

policy-based-route

policy-based-route

Use policy-based-route to create a policy node and enter its view, or enter the view of an existing policy node.

Use undo policy-based-route to delete a policy or policy node.

Syntax

policy-based-route policy-name [ deny | permit ] node node-number

undo policy-based-route policy-name [ deny | node node-number | permit ]

Default

No policy nodes exist.

Views

System view

Predefined user roles

network-admin

Parameters

policy-name: Specifies a policy by its name, a case-sensitive string of 1 to 19 characters.

deny: Specifies the match mode for the policy node as deny.

permit: Specifies the match mode for the policy node as permit (default mode).

node node-number: Specifies a policy node by its number. A smaller number has a higher priority. The value range for the node-number argument is 0 to 255.

Usage guidelines

A policy that has been applied to an interface or locally cannot be deleted. To delete it, you must first cancel the application.

·          If a policy node is specified, the undo policy-based-route command deletes the specified policy node.

·          If a match mode is specified, the command deletes all nodes configured with the match mode.

·          If no policy node or match mode is specified, the command deletes the whole policy.

Examples

# Create permit-mode of Node 10 for policy policy1 and enter its view.

<Sysname> system-view

[Sysname] policy-based-route policy1 permit node 10

[Sysname-pbr-policy1-10]

Related commands

display ip policy-based-route

reset ip policy-based-route statistics

Use reset ip policy-based-route statistics to clear PBR statistics.

Syntax

reset ip policy-based-route statistics [ policy policy-name ]

Views

User view

Predefined user roles

network-admin

Parameters

policy policy-name: Specifies a policy by its name, a case-sensitive string of 1 to 19 characters. If you do not specify a policy, this command clears PBR statistics for all policies.

Examples

# Clear all PBR statistics.

<Sysname> reset ip policy-based-route statistics

Related commands

display ip policy-based-route interface

display ip policy-based-route local