Contents

Routing policy commands· 1

Common routing policy commands· 1

apply cost 1

apply cost-type· 1

apply ip-precedence· 2

apply preference· 3

apply prefix-priority· 3

apply tag· 4

continue· 4

display route-policy· 5

if-match cost 6

if-match interface· 6

if-match route-type· 7

if-match tag· 8

route-policy· 8

IPv4 routing policy commands· 9

apply fast-reroute· 9

apply ip-address next-hop· 10

display ip prefix-list 10

if-match ip· 11

ip prefix-list 12

reset ip prefix-list 13

IPv6 routing policy commands· 14

apply ipv6 fast-reroute· 14

apply ipv6 next-hop· 15

display ipv6 prefix-list 15

if-match ipv6· 16

ipv6 prefix-list 17

reset ipv6 prefix-list 18

 

Routing policy commands

Common routing policy commands

apply cost

Use apply cost to set a cost for routes.

Use undo apply cost to restore the default.

Syntax

apply cost [ + | - ] cost-value

undo apply cost

Default

No cost is set for routes.

Views

Routing policy node view

Predefined user roles

network-admin

Parameters

+: Increases a cost value.

-: Decreases a cost value.

cost-value: Specifies a cost in the range of 0 to 4294967295.

Examples

# Configure node 10 in permit mode for routing policy policy1 to set a cost of 120 for OSPF external routes.

<Sysname> system-view

[Sysname] route-policy policy1 permit node 10

[Sysname-route-policy-policy1-10] if-match route-type external-type1or2

[Sysname-route-policy-policy1-10] apply cost 120

apply cost-type

Use apply cost-type to set a cost type for routes.

Use undo apply cost-type to restore the default.

Syntax

apply cost-type { type-1 | type-2 }

undo apply cost-type

Default

No cost type is set for routes.

Views

Routing policy node view

Predefined user roles

network-admin

Parameters

type-1: Sets the cost type to OSPF Type-1 external route.

type-2: Sets the cost type to OSPF Type-2 external route.

Examples

# Configure node 10 in permit mode for routing policy policy1 to set the cost type for routes that have a tag of 8 to OSPF Type-1 external routes.

<Sysname> system-view

[Sysname] route-policy policy1 permit node 10

[Sysname-route-policy-policy1-10] if-match tag 8

[Sysname-route-policy-policy1-10] apply cost-type type-1

apply ip-precedence

Use apply ip-precedence to set an IP precedence for matching routes.

Use undo apply ip-precedence to restore the default.

Syntax

apply ip-precedence { value | clear }

undo apply ip-precedence

Default

No IP precedence is set.

Views

Routing policy node view

Predefined user roles

network-admin

Parameters

value: Specifies an IP precedence in the range of 0 to 7.

clear: Clears the IP precedence of matching routes.

Examples

# Configure node 10 in permit mode for routing policy policy1 to set an IP precedence of 3 for routes matching prefix list 100.

<Sysname> system-view

[Sysname] ip prefix-list 100 permit 192.168.10.1 24

[Sysname] route-policy policy1 permit node 10

[Sysname-route-policy-policy1-10] if-match ip address prefix-list 100

[Sysname-route-policy-policy1-10] apply ip-precedence 3

apply preference

Use apply preference to set a preference for a routing protocol.

Use undo apply preference to restore the default.

Syntax

apply preference preference

undo apply preference

Default

No preference is set for a routing protocol.

Views

Routing policy node view

Predefined user roles

network-admin

Parameters

preference: Specifies a preference in the range of 1 to 255.

Usage guidelines

If you have set preferences for routing protocols by using the preference command, the apply preference command sets a new preference for the matching routing protocol. Unmatched routing protocols still use the preferences set by using the preference command.

Examples

# Configure node 10 in permit mode for routing policy policy1 to set the preference for OSPF external routes to 90.

<Sysname> system-view

[Sysname] route-policy policy1 permit node 10

[Sysname-route-policy-policy1-10] if-match route-type external-type1or2

[Sysname-route-policy-policy1-10] apply preference 90

apply prefix-priority

Use apply prefix-priority to set a prefix priority for routes.

Use undo apply prefix-priority to restore the default.

Syntax

apply prefix-priority { critical | high | medium }

undo apply prefix-priority

Default

No prefix priority is set, which means the prefix priority is low.

Views

Routing policy node view

Predefined user roles

network-admin

Parameters

critical: Sets the critical prefix priority for routes.

high: Sets the high prefix priority for routes.

medium: Sets the medium prefix priority for routes.

Examples

# Configure node 10 in permit mode for routing policy policy1 to set prefix priority critical for routes matching prefix list abc.

<Sysname> system-view

[Sysname] route-policy policy1 permit node 10

[Sysname-route-policy-policy1-10] if-match ip address prefix-list abc

[Sysname-route-policy-policy1-10] apply prefix-priority critical

apply tag

Use apply tag to set a tag for IGP routes.

Use undo apply tag to restore the default.

Syntax

apply tag tag-value

undo apply tag

Default

No routing tag is set for IGP routes.

Views

Routing policy node view

Predefined user roles

network-admin

Parameters

tag-value: Specifies the tag value in the range of 0 to 4294967295.

Examples

# Configure node 10 in permit mode for routing policy policy1 to set a tag of 100 for IGP routes.

<Sysname> system-view

[Sysname] route-policy policy1 permit node 10

[Sysname-route-policy-policy1-10] apply tag 100

continue

Use continue to specify the next node to be matched.

Use undo continue to restore the default.

Syntax

continue [ node-number ]

undo continue

Default

No next node is specified.

Views

Routing policy node view

Predefined user roles

network-admin

Parameters

node-number: Specifies the routing policy node number in the range of 0 to 65535.

Usage guidelines

The specified next node must have a larger number than the current node.

Example

# Specify the next node 20 for node 10 of the routing policy policy1.

<Sysname> system-view

[Sysname] route-policy policy1 permit node 10

[Sysname-route-policy-policy1-10] continue 20

display route-policy

Use display route-policy to display routing policy information.

Syntax

display route-policy [ name route-policy-name ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

name route-policy-name: Specifies a routing policy by its name, a case-sensitive string of 1 to 63 characters. If you do not specify this option, the command displays information about all routing policies.

Examples

# Display information about routing policy policy1.

<Sysname> display route-policy name policy1

Route-policy: policy1

  Permit : 1

          if-match cost 10

          continue: next node 11

          apply preference 10

Table 1 Command output

Field	Description
Route-policy	Routing policy name.
permit	Match mode: ·         Permit. ·         Deny.
if-match	Match criterion.
continue	Specify the next node to be matched.
apply	Action.

 

if-match cost

Use if-match cost to match routes that have the specified cost.

Use undo if-match cost to restore the default.

Syntax

if-match cost cost-value

undo if-match cost

Default

No cost match criterion is configured.

Views

Routing policy node view

Predefined user roles

network-admin

Parameters

cost-value: Specifies a cost in the range of 0 to 4294967295.

Examples

# Configure node 10 in permit mode for routing policy policy1 to permit routes with a cost of 8.

<Sysname> system-view

[Sysname] route-policy policy1 permit node 10

[Sysname-route-policy-policy1-10] if-match cost 8

if-match interface

Use if-match interface to match routes that have the specified output interfaces.

Use undo if-match interface to remove the specified output interface match criterion.

Syntax

if-match interface { interface-type interface-number }&<1-16>

undo if-match interface [ interface-type interface-number ]&<1-16>

Default

No output interface match criterion is configured.

Views

Routing policy node view

Predefined user roles

network-admin

Parameters

interface-type interface-number: Specifies an interface by its type and number.

&<1-16>: Indicates that you can specify a maximum of 16 interfaces.

Examples

# Configure node 10 in permit mode for routing policy policy1 to permit routes with the output interface VLAN-interface 1.

<Sysname> system-view

[Sysname] route-policy policy1 permit node 10

[Sysname-route-policy-policy1-10] if-match interface vlan-interface 1

if-match route-type

Use if-match route-type to set a route-type match criterion.

Use undo if-match route-type to remove the specified route-type match criterion.

Syntax

if-match route-type { external-type1 | external-type1or2 | external-type2 | internal | nssa-external-type1 | nssa-external-type1or2 | nssa-external-type2 } *

undo if-match route-type [ external-type1 | external-type1or2 | external-type2 | internal | nssa-external-type1 | nssa-external-type1or2 | nssa-external-type2 ] *

Default

No route-type match criterion is set.

Views

Routing policy node view

Predefined user roles

network-admin

Parameters

external-type1: Matches OSPF Type 1 external routes.

external-type1or2: Matches OSPF Type 1 and Type 2 external routes.

external-type2: Matches OSPF Type 2 external routes.

internal: Matches OSPF internal routes (including OSPF intra-area and inter-area routes).

nssa-external-type1: Matches OSPF NSSA Type 1 external routes.

nssa-external-type1or2: Matches OSPF NSSA Type 1 and 2 external routes.

nssa-external-type2: Matches OSPF NSSA Type 2 external routes.

Examples

# Configure node 10 in permit mode for routing policy policy1 to match OSPF internal routes.

<Sysname> system-view

[Sysname] route-policy policy1 permit node 10

[Sysname-route-policy-policy1-10] if-match route-type internal

if-match tag

Use if-match tag to match IGP routes that have the specified tag.

Use undo if-match tag to restore the default.

Syntax

if-match tag tag-value

undo if-match tag

Default

No tag match criterion is configured.

Views

Routing policy node view

Predefined user roles

network-admin

Parameters

tag-value: Specifies a tag in the range of 0 to 4294967295.

Examples

# Configure node 10 in permit mode for routing policy policy1 to match IGP routes that have a tag of 8.

<Sysname> system-view

[Sysname] route-policy policy1 permit node 10

[Sysname-route-policy-policy1-10] if-match tag 8

route-policy

Use route-policy to create a routing policy and a node and enter routing policy node view, or enter the view of an existing routing policy node.

Use undo route-policy to remove a routing policy or a node of it.

Syntax

route-policy route-policy-name { deny | permit } node node-number

undo route-policy route-policy-name [ deny | permit ] [ node node-number ]

Default

No routing policies exist.

Views

System view

Predefined user roles

network-admin

Parameters

route-policy-name: Specifies a routing policy name, a case-sensitive string of 1 to 63 characters.

deny: Specifies the deny match mode for the routing policy node. If a route matches all the if-match clauses of the node, it is denied without being compared with the next node. If a route does not match any if-match clauses of the node, the route is compared with the next node.

permit: Specifies the permit match mode for the routing policy node. If a route matches all the if-match clauses of the node, it is handled by the apply clauses of the node. If a route does not match any if-match clauses of the node, the route is compared with the next node.

node node-number: Specifies a node number in the range of 0 to 65535. A node with a smaller number is matched first.

Usage guidelines

Use a routing policy to filter routing information. A routing policy can contain several nodes and each node contains a set of if-match and apply clauses. The if-match clauses define the match criteria of the node and the apply clauses define the actions to be taken on packets matching the criteria. The relation between the if-match clauses of a node is logical AND. All the if-match clauses must be met. The relation between nodes is logical OR. A packet passing a node passes the routing policy. If a packet does not pass any nodes, the packet does not pass the routing policy.

Examples

# Create node 10 in permit mode for routing policy policy1 and enter routing policy node view.

<Sysname> system-view

[Sysname] route-policy policy1 permit node 10

[Sysname-route-policy-policy1-10]

Related commands

display route-policy

IPv4 routing policy commands

apply fast-reroute

Use apply fast-reroute to set a backup link for fast reroute (FRR).

Use undo apply fast-reroute to restore the default.

Syntax

apply fast-reroute { backup-interface interface-type interface-number [ backup-nexthop ip-address ] | backup-nexthop ip-address }

undo apply fast-reroute

Default

No backup link for FRR is configured.

Views

Routing policy node view

Predefined user roles

network-admin

Parameters

backup-interface interface-type interface-number: Specifies a backup output interface by its type and number. If the specified interface is a non-P2P interface, you must also specify a backup next hop. Non-P2P interfaces include NBMA and broadcast interfaces.

backup-nexthop ip-address: Specifies a backup next hop.

Examples

# Configure node 10 of routing policy policy1 to set the backup output interface VLAN-interface 1 and backup next hop 193.1.1.8 for the route destined for 100.1.1.0/24.

<Sysname> system-view

[Sysname] ip prefix-list abc index 10 permit 100.1.1.0 24

[Sysname] route-policy policy1 permit node 10

[Sysname-route-policy-policy1-10] if-match ip address prefix-list abc

[Sysname-route-policy-policy1-10] apply fast-reroute backup-interface vlan-interface 1 backup-nexthop 193.1.1.8

apply ip-address next-hop

Use apply ip-address next-hop to set a next hop for IPv4 routes.

Use undo apply ip-address next-hop to restore the default.

Syntax

apply ip-address next-hop ip-address [ public ]

undo apply ip-address next-hop

Default

No next hop is set for IPv4 routes.

Views

Routing policy node view

Predefined user roles

network-admin

Parameters

ip-address: Specifies the next hop IP address.

public: Specifies the public network.

Usage guidelines

If you use this command to set a next hop for redistributed routes, the configuration does not take effect.

If you do not specify the public keyword, the next hop belongs to the public network.

Examples

# Configure node 10 in permit mode for routing policy policy1 to set next hop 193.1.1.8 for routes matching prefix list 100.

<Sysname> system-view

[Sysname] ip prefix-list 100 permit 192.168.10.1 24

[Sysname] route-policy policy1 permit node 10

[Sysname-route-policy-policy1-10] if-match ip address prefix-list 100

[Sysname-route-policy-policy1-10] apply ip-address next-hop 193.1.1.8

display ip prefix-list

Use display ip prefix-list to display IPv4 prefix list statistics.

Syntax

display ip prefix-list [ name prefix-list-name ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

name prefix-list-name: Specifies an IP prefix list by its name, a case-sensitive string of 1 to 63 characters. If you do not specify this option, the command displays statistics for all IPv4 prefix lists.

Examples

# Display the statistics for IPv4 prefix list abc.

<Sysname> display ip prefix-list name abc

Prefix-list: abc

 Permitted 0

 Denied 0

         index: 10        Deny   6.6.6.0/24              ge  26  le  28

Table 2 Command output

Field	Description
Prefix-list	Name of the IPv4 prefix list.
Permitted	Number of routes matching the criterion.
Denied	Number of routes not matching the criterion.
index	Index of an item.
deny	Match mode of the item: ·         Permit. ·         Deny.
6.6.6.0/24	IP address and mask.
ge	Greater-equal, the lower mask length limit.
le	Less-equal, the upper mask length limit.

 

Related commands

ip prefix-list

reset ip prefix-list

if-match ip

Use if-match ip to match IPv4 routes whose destination, next hop, or source address matches an ACL or IPv4 prefix list.

Use undo if-match ip to remove the specified ACL or IPv4 prefix list match criterion.

Syntax

if-match ip { address | next-hop } { acl ipv4-acl-number | prefix-list prefix-list-name }

undo if-match ip { address | next-hop | route-source } [ acl | prefix-list ]

Default

No ACL or IPv4 prefix list match criterion is configured.

Views

Routing policy node view

Predefined user roles

network-admin

Parameters

address: Matches the destination address of IPv4 routes.

next-hop: Matches the next hop of IPv4 routes.

acl ipv4-acl-number: Specifies an ACL by its number. The value range for the ipv4-acl-number argument is 2000 to 3999 for the address keyword, and 2000 to 2999 for the next-hop keyword and route-source keyword.

prefix-list prefix-list-name: Specifies an IP prefix list by its name, a case-sensitive string of 1 to 63 characters.

Examples

# Configure node 10 of routing policy policy1 to match IPv4 routes whose next hop matches IP prefix list p1.

<Sysname> system-view

[Sysname] route-policy policy1 permit node 10

[Sysname-route-policy-policy1-10] if-match ip next-hop prefix-list p1

ip prefix-list

Use ip prefix-list to configure an IPv4 prefix list or an item for the list.

Use undo ip prefix-list to remove an IPv4 prefix list or an item of it.

Syntax

ip prefix-list prefix-list-name [ index index-number ] { deny | permit } ip-address mask-length [ greater-equal min-mask-length ] [ less-equal max-mask-length ]

undo ip prefix-list prefix-list-name [ index index-number ]

Default

No IPv4 prefix lists exist.

Views

System view

Predefined user roles

network-admin

Parameters

prefix-list-name: Specifies an IPv4 prefix list name, a case-sensitive string of 1 to 63 characters.

index index-number: Specifies an index number for an IPv4 prefix list item, in the range of 1 to 65535. An item with a smaller index number is matched first. If you do not specify this option, the index number starts from 10 and increments by 10 for each of the consecutive prefix list items.

deny: Specifies the deny mode. If a route matches the item, the route is denied without being compared with the next item. If a route does not match the item, the route is compared with the next item.

permit: Specifies the permit mode. If a route matches the item, it passes the IPv4 prefix list. If a route does not match the item, the route is compared with the next item.

ip-address mask-length: Specifies an IPv4 prefix and mask length. The value range for the mask-length argument is 0 to 32.

greater-equal min-mask-length, less-equal max-mask-length: Specifies a prefix length range. The greater-equal keyword means "greater than or equal to" and the less-equal keyword means "less than or equal to." The prefix length range relation is mask-length <= min-mask-length <= max-mask-length <= 32.

·          If only the min-mask-length argument is specified, the prefix length range is [ min-mask-length, 32 ].

·          If only the max-mask-length argument is specified, the prefix length range is [ mask-length, max-mask-length ].

·          If both the min-mask-length and max-mask-length arguments are specified, the prefix length range is [ min-mask-length, max-mask-length ].

Usage guidelines

An IPv4 prefix list is used to filter IPv4 addresses. It can contain multiple items, each of which specifies a range of IPv4 prefixes. The relation between the items is logical OR. If an item is passed, the IPv4 prefix list is passed. If no item is passed, the IP prefix list cannot be passed.

If both the ip-address and mask-length arguments are specified as 0.0.0.0 0, only the default route will be matched.

To match all routes, use 0.0.0.0 0 less-equal 32.

Examples

# Configure IP prefix list p1 to permit routes destined for network 10.0.0.0/8 and with mask length 17 or 18.

<Sysname> system-view

[Sysname] ip prefix-list p1 permit 10.0.0.0 8 greater-equal 17 less-equal 18

Related commands

display ip prefix-list

reset ip prefix-list

reset ip prefix-list

Use reset ip prefix-list to clear IPv4 prefix list statistics.

Syntax

reset ip prefix-list [ prefix-list-name ]

Views

User view

Predefined user roles

network-admin

Parameters

prefix-list-name: Specifies an IP prefix list by its name, a case-sensitive string of 1 to 63 characters. If you do not specify this argument, the command clears statistics for all IPv4 prefix lists.

Examples

# Clear the statistics for IPv4 prefix list abc.

<Sysname> reset ip prefix-list abc

Related commands

display ip prefix-list

ip prefix-list

IPv6 routing policy commands

apply ipv6 fast-reroute

Use apply ipv6 fast-reroute to set a backup link for fast reroute (FRR).

Use undo apply ipv6 fast-reroute to restore the default.

Syntax

apply ipv6 fast-reroute { backup-interface interface-type interface-number [ backup-nexthop ipv6-address ] | backup-nexthop ipv6-address }

undo apply ipv6 fast-reroute

Default

No backup link for FRR is configured.

Views

Routing policy node view

Predefined user roles

network-admin

Parameters

backup-interface interface-type interface-number: Specifies a backup output interface by its type and number. If the specified interface is a non-P2P interface, you must also specify a backup next hop. Non-P2P interfaces include NBMA and broadcast interfaces.

backup-nexthop ipv6-address: Specifies an IPv6 backup next hop.

Examples

# Configure node 10 of routing policy policy1 to set the backup next hop 1::1/64 for the route destined for 100::1/64.

<Sysname> system-view

[Sysname] ipv6 prefix-list abc index 10 permit 100::1 64

[Sysname] route-policy policy1 permit node 10

[Sysname-route-policy-policy1-10] if-match ipv6 address prefix-list abc

[Sysname-route-policy-policy1-10] apply ipv6 fast-reroute backup-nexthop 1::1

apply ipv6 next-hop

Use apply ipv6 next-hop to set a next hop for IPv6 routes.

Use undo apply ipv6 next-hop to restore the default.

Syntax

apply ipv6 next-hop ipv6-address

undo apply ipv6 next-hop

Default

No next hop is set for IPv6 routes.

Views

Routing policy node view

Predefined user roles

network-admin

Parameters

ipv6-address: Specifies the next hop IPv6 address.

Usage guidelines

If you use this command to set a next hop for redistributed routes, the configuration does not take effect.

Examples

# Configure node 10 in permit mode for routing policy policy1 to set next hop 3ffe:506::1 for IPv6 routes matching prefix list 100.

<Sysname> system-view

[Sysname] ipv6 prefix-list 100 permit 2::2 64

[Sysname] route-policy policy1 permit node 10

[Sysname-route-policy-policy1-10] if-match ipv6 address prefix-list 100

[Sysname-route-policy-policy1-10] apply ipv6 next-hop 3ffe:506::1

display ipv6 prefix-list

Use display ipv6 prefix-list to display IPv6 prefix list statistics.

Syntax

display ipv6 prefix-list [ name prefix-list-name ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

name prefix-list-name: Specifies an IPv6 prefix list by its name, a case-sensitive string of 1 to 63 characters. If you do not specify this option, the command displays statistics for all IPv6 prefix lists.

Examples

# Display the statistics for all IPv6 prefix lists.

<Sysname> display ipv6 prefix-list

Prefix-list6: 666

 Permitted 0

 Denied 0

         index: 10        Permit 6::/64                  ge  66  le  88

Table 3 Command output

Field	Description
Prefix-list6	Name of the IPv6 prefix list.
Permitted	Number of routes matching the criterion.
Denied	Number of routes not matching the criterion.
index	Index number of an item.
permit	Match mode of the item: ·         Permit. ·         Deny.
6::/64	IPv6 address and prefix length for matching.
ge	Greater-equal, the lower prefix length limit.
le	Less-equal, the upper prefix length limit.

 

Related commands

ipv6 prefix-list

reset ipv6 prefix-list

if-match ipv6

Use if-match ipv6 to match IPv6 routes whose destination, next hop, or source address matches an ACL or IPv6 prefix list.

Use undo if-match ipv6 to remove the specified ACL or IPv6 prefix list match criterion.

Syntax

if-match ipv6 { address | next-hop | route-source } { acl ipv6-acl-number | prefix-list prefix-list-name

undo if-match ipv6 { address | next-hop | route-source } [ acl | prefix-list ]

Default

No ACL or IPv6 prefix list match criterion is configured.

Views

Routing policy node view

Predefined user roles

network-admin

Parameters

address: Matches the destination address of IPv6 routes.

next-hop: Matches the next hop of IPv6 routes.

route-source: Matches the source address of IPv6 routes.

acl ipv6-acl-number: Specifies an IPv6 ACL by its number. The value range for the ipv6-acl-number argument is 2000 to 3999 for the address keyword, and 2000 to 2999 for the next-hop and route-source keywords.

prefix-list prefix-list-name: Specifies an IPv6 prefix list by its name, a case-sensitive string of 1 to 63 characters.

Examples

# Configure node 10 of routing policy policy1 to permit routes whose next hop matches IPv6 prefix list p1.

<Sysname> system-view

[Sysname] route-policy policy1 permit node 10

[Sysname-route-policy-policy1-10] if-match ipv6 next-hop prefix-list p1

ipv6 prefix-list

Use ipv6 prefix-list to configure an IPv6 prefix list or an item for it.

Use undo ipv6 prefix-list to remove an IPv6 prefix list or an item.

Syntax

ipv6 prefix-list prefix-list-name [ index index-number ] { deny | permit } ipv6-address { prefix-length [ greater-equal min-prefix-length ] [ less-equal max-prefix-length ] | inverse inverse-prefix-length }

undo ipv6 prefix-list prefix-list-name [ index index-number ]

Default

No IPv6 prefix lists exist.

Views

System view

Predefined user roles

network-admin

Parameters

prefix-list-name: Specifies an IPv6 prefix list name, a case-sensitive string of 1 to 63 characters.

index index-number: Specifies an index number for an IPv6 prefix list item, in the range of 1 to 65535. An item with a smaller index number is matched first. If you do not specify this option, the index number starts from 10 and increments by 10 for each of the consecutive IPv6 prefix list items.

deny: Specifies the deny mode. If a route matches the item, the route is denied without being compared with the next item. If a route does not match the item, the route is compared with the next item.

permit: Specifies the permit mode. If a route matches the item, it passes the IPv6 prefix list. If a route does not match the item, the route is compared with the next item.

ipv6-address: Specifies an IPv6 address.

prefix-length: Specifies the IPv6 prefix length. The value range for the prefix-length argument is 0 to 128.

greater-equal min-mask-length, less-equal max-mask-length: Specifies a prefix length range. The greater-equal keyword means "greater than or equal to" and the less-equal keyword means "less than or equal to."

The prefix length range relation is mask-length <= min-mask-length <= max-mask-length <= 128.

·          If only the min-prefix-length argument is specified, the prefix length range is [ min-prefix-length, 128 ].

·          If only the max-prefix-length argument is specified, the prefix length range is [ prefix-length, max-prefix-length ].

·          If both the min-prefix-length and max-prefix-length arguments are specified, the prefix length range is [ min-prefix-length, max-prefix-length ].

inverse inverse-prefix-length: Matches IPv6 addresses from the least significant bit to the specified length. The value range for the inverse-prefix-length argument is 1 to 128.

Usage guidelines

An IPv6 prefix list is used to filter IPv6 addresses. An IPv6 prefix list can have multiple items, and each of them specifies a range of IPv6 prefixes. The relation between the items is logical OR. A route passing an item passes the IPv6 prefix list. A route passing no item does not pass the IPv6 prefix list.

If the ipv6-address prefix-length argument is specified as :: 0, only the default route matches.

To match all routes, configure :: 0 less-equal 128.

Examples

# Permit IPv6 addresses with a mask length between 32 bits and 64 bits.

<Sysname> system-view

[Sysname] ipv6 prefix-list abc permit :: 0 greater-equal 32 less-equal 64

# Deny IPv6 addresses with a prefix 3FFE:D00::/32 and a prefix length greater than or equal to 32 bits.

<Sysname> system-view

[Sysname] ipv6 prefix-list abc deny 3FFE:D00:: 32 less-equal 128

Related commands

display ipv6 prefix-list

reset ipv6 prefix-list

reset ipv6 prefix-list

Use reset ipv6 prefix-list to clear IPv6 prefix list statistics.

Syntax

reset ipv6 prefix-list [ prefix-list-name ]

Views

User view

Predefined user roles

network-admin

Parameters

prefix-list-name: Specifies an IPv6 prefix list by its name, a case-sensitive string of 1 to 63 characters. If you do not specify this argument, the command clears statistics for all IPv6 prefix lists.

Examples

# Clear the statistics for IPv6 prefix list abc.

<Sysname> reset ipv6 prefix-list abc

Related commands

display ipv6 prefix-list

ipv6 prefix-list