Field	Description
Ten-GigabitEthernet1/0/1	Information on Ten-GigabitEthernet 1/0/1.
Enable status	Ethernet OAM state (enabled or disabled).
Loopback status	Ethernet OAM loopback state: · No loopback. · Remote loopback. · Local loopback.
Link status	Link state (UP or DOWN).
OAM mode	Local Ethernet OAM mode: · Active—The port operates in the active Ethernet OAM mode. · Passive—The port operates in the passive Ethernet OAM mode.
PDU	The way in which the local end processes Ethernet OAMPDUs: · RX_INFO—The port only receives Information OAMPDUs and does not send any Ethernet OAMPDUs. · LF_INFO—The port only sends the Information OAMPDUs without Information TLV triplets and with their link error flag bits being set. · INFO—The port sends and receives only Information OAMPDUs. · ANY—The port sends and receives Ethernet OAMPDUs of any type.
Mux action	Operating mode of the local transmitter: · FWD—The port can send any packets. · DISCARD—The port only sends Ethernet OAMPDUs.
Par action	Operating mode of the local receiver: · FWD—The port can receive any packets. · DISCARD—The port only receives Ethernet OAMPDUs. · LB—The local receiver is in loopback state. All the packets, other than Ethernet OAMPDUs, received on the local receiver are returned to their sources along their original routes.
Flags	Local flags inserted in the local flag fields of the Ethernet OAMPDUs sent.
Link fault	Indicates whether an Ethernet OAM link error is present.
Dying gasp	Indicates whether a fatal error is present.
Critical event	Indicates whether a critical error is present.
Local evaluating	Indicates whether the local-to-remote configuration negotiation is complete: · COMPLETE—The negotiation is completed. · NOTCOMPLETE—The negotiation is uncompleted.
Remote evaluating	Indicates whether the remote-to-local configuration negotiation is complete: · COMPLETE—The negotiation is completed. · NOTCOMPLETE—The negotiation is uncompleted. · RESERVED—The field is reserved and the negotiation is uncompleted. · UNSATISFIED—The remote end is not satisfied with the local configuration and the negotiation is uncompleted.
Packets statistics	Statistics about Ethernet OAMPDUs sent and received.
OAMPDU	Total number of the Ethernet OAMPDUs sent and received.
OAMInformation	Number of the Information OAMPDUs sent and received.
OAMEventNotification	Number of the Event notification OAMPDUs sent and received.
OAMUniqueEventNotification	Number of the unduplicated Event notification OAMPDUs sent or received uniquely.
OAMDuplicateEventNotification	Number of the duplicate Event notification OAMPDUs sent or received.

Field	Description
Ten-GigabitEthernet1/0/1	Information on Ten-GigabitEthernet 1/0/1.
OAM mode	Local Ethernet OAM mode: · Active—The port operates in the active Ethernet OAM mode. · Passive—The port operates in the passive Ethernet OAM mode.
MAC address	MAC address of the remote end.
MTU size	MTU size, in bytes.
Mux action	Operating mode of the remote transmitter: · FWD—The port can send any packets. · DISCARD—The port only sends Ethernet OAMPDUs.
Par action	Operating mode of the remote receiver: · FWD—The port can receive any packets. · DISCARD—The port only receives Ethernet OAMPDUs. · LB—The local receiver is in loopback state. All the packets, other than Ethernet OAMPDUs, received on the local receiver are returned to their sources along their original routes.
Configuration	Configuration of the remote Ethernet OAM entity.
Unidirectional	Indicates whether unidirectional transmission is supported.
Remote loopback	Indicates whether Ethernet OAM remote loopback is supported.
Link events	Indicates whether Ethernet OAM link error events are supported.
MIB retrieval	Indicates whether MIB variable retrieval is supported.
Flags	Values of the peer Ethernet OAM flag fields in OAM packets.
Link fault	Indicates whether an Ethernet OAM link error is present.
Dying gasp	Indicates whether a fatal error is present.
Critical event	Indicates whether a critical error is present.
Local evaluating	Indicates whether the local-to-remote configuration negotiation is complete: · COMPLETE—The negotiation is completed. · NOTCOMPLETE—The negotiation is uncompleted. · RESERVED—The field is reserved and the negotiation is uncompleted. · UNSATISFIED—The remote end is not satisfied with the local configuration and the negotiation is uncompleted.
Remote evaluating	Indicates whether the remote-to-local configuration negotiation is complete: · COMPLETE—The negotiation is completed. · NOTCOMPLETE—The negotiation is uncompleted. · UNSATISFIED—The remote end is not satisfied with the local configuration and the negotiation is uncompleted.

display oam configuration

Use display oam configuration to display global Ethernet OAM configuration on the specified port, including the periods and thresholds for Ethernet OAM link error event detection.

Syntax

display oam configuration [ interface interface-type interface-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

interface interface-type interface-number: Specifies a port by its type and number.

Usage guidelines

If you do not specify the interface keyword, the command displays Ethernet OAM configuration globally and on ports that do not use the default configuration.

Examples

# Display Ethernet OAM configuration globally and on ports that do not use the default configuration.

<Sysname> display oam configuration

---------------- [Global] ----------------

OAM timers

Hello timer : 1000 milliseconds

Keepalive timer : 5000 milliseconds

Link monitoring

Errored symbol period

Window : 100 x 1000000 symbols

Threshold : 1 error symbols

Errored frame

Window : 10 x 100 milliseconds

Threshold : 1 error frames

Errored frame period

Window : 1000 x 10000 frames

Threshold : 1 error frames

Errored frame seconds

Window : 600 x 100 milliseconds

Threshold : 1 error seconds

----------- [Ten-GigabitEthernet1/0/1] -----------

OAM timers

Hello timer : 500 milliseconds

Keepalive timer : 5000 milliseconds

Link monitoring

Errored symbol period

Window : 100 x 1000000 symbols

Threshold : 1 error symbols

Errored frame

Window : 10 x 100 milliseconds

Threshold : 1 error frames

Errored frame period

Window : 1000 x 10000 frames

Threshold : 1 error frames

Errored frame seconds

Window : 600 x 100 milliseconds

Threshold : 1 error seconds

Table 3 Command output

Field	Description
Global	Global information.
Ten-GigabitEthernet1/0/1	Information on Ten-GigabitEthernet 1/0/1.
OAM timers	Ethernet OAM connection detection timers.
Hello timer	Ethernet OAM handshake packet transmission interval.
Keepalive timer	Ethernet OAM connection timeout timer.
Link monitoring	Link event detection window and threshold.
Errored symbol period	Errored symbol event.
Errored frame	Errored frame event.
Errored frame period	Errored frame period event.
Errored frame seconds	Errored frame seconds event.
Window	Detection window configured for link events.
Threshold	Triggering threshold configured for link events.

display oam critical-event

Use display oam critical-event to display the statistics of critical Ethernet OAM link events that occurred on a port.

Syntax

display oam critical-event [ interface interface-type interface-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

interface interface-type interface-number: Specifies a port by its type and number.

Usage guidelines

If you do not specify the interface keyword, the command displays the statistics of the critical Ethernet OAM link events that occurred on all the ports of the switch.

Examples

# Display the statistics of critical Ethernet OAM link events that occurred on all the ports.

<Sysname> display oam critical-event

----------- [Ten-GigabitEthernet1/0/1] -----------

Local link status : UP

Event statistics

Link fault : Not occurred

Dying gasp : Not occurred

Critical event : Not occurred

Table 4 Command output

Field	Description
Ten-GigabitEthernet1/0/1	Information on Ten-GigabitEthernet 1/0/1.
Local link status	Local link status, up or down.
Event statistics	Statistics of critical Ethernet OAM link events.
Link fault	Indicates whether a link fault is present.
Dying Gasp	Indicates whether a fatal fault is present.
Critical Event	Indicates whether a critical fault is present.

Use display oam link-event to display the statistics of Ethernet OAM link error events that occurred on a local port or a peer port. Ethernet OAM link error events include errored symbol events, errored frame events, errored frame period events, and errored frame seconds events.

Syntax

display oam link-event { local | remote } [ interface interface-type interface-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

local: Displays the statistics on the local Ethernet OAM link error events.

remote: Displays the statistics on the peer Ethernet OAM link error events.

interface interface-type interface-number: Specifies a port by its type and number.

Usage guidelines

If you do not specify the interface keyword, the command displays the statistics of the Ethernet OAM link error events that occurred on all the local/peer ports.

Examples

# Display the statistics of Ethernet OAM link error events that occurred on all the local ports.

<Sysname> display oam link-event local

----------- [Ten-GigabitEthernet1/0/1] -----------

Link status: UP

OAM local errored frame event

Event time stamp : 49582 x 100 milliseconds

Errored frame window : 10 x 100 milliseconds

Errored frame threshold : 1 error frames

Errored frame : 1 error frames

Error running total : 6 error frames

Event running total : 6 events

OAM local errored frame period event

Event time stamp : 16382 x 100 milliseconds

Errored frame period window : 10000000 frames

Errored frame period threshold : 1 error frames

Errored frame period : 1 error frames

Error running total : 5 error frames

Event running total : 5 events

OAM local errored frame seconds summary event

Event time stamp : 50022 x 100 milliseconds

Errored frame seconds window : 600 x 100 milliseconds

Errored frame seconds threshold : 1 error seconds

Errored frame seconds : 1 error seconds

Error running total : 1 error seconds

Event running total : 1 events

# Display Ethernet OAM link event statistics of the remote ends of all the ports.

<Sysname> display oam link-event remote

----------- [Ten-GigabitEthernet1/0/1] -----------

Link status: UP

OAM remote errored symbol event

Event time stamp : 35498 x 100 milliseconds

Errored symbol window : 100000000 symbols

Errored symbol threshold : 1 error symbols

Errored symbol : 1 error symbols

Error running total : 4 error symbols

Event running total : 4 events

OAM remote errored frame event

Event time stamp : 49582 x 100 milliseconds

Errored frame window : 10 x 100 milliseconds

Errored frame threshold : 1 error frames

Errored frame : 1 error frames

Error running total : 6 error frames

Event running total : 6 events

OAM remote errored frame period event

Event time stamp : 16382 x 100 milliseconds

Errored frame period window : 10000000 frames

Errored frame period threshold : 1 error frames

Errored frame period : 1 error frames

Error running total : 5 error frames

Event running total : 5 events

OAM remote errored frame seconds summary event

Event time stamp : 50022 x 100 milliseconds

Errored frame seconds window : 600 x 100 milliseconds

Errored frame seconds threshold : 1 error seconds

Errored frame seconds : 1 error seconds

Error running total : 1 error seconds

Event running total : 1 events

Table 5 Command output

Field	Description
Ten-GigabitEthernet1/0/1	Information on Ten-GigabitEthernet 1/0/1.
Link status	Link status, up or down.
OAM remote errored symbol event	Information about remote errored symbol events (available only when remote errored symbol events occur): · Event time stamp—Time when an errored symbol event occurred. · Errored symbol window—Errored symbol detection interval. · Errored symbol threshold—Errored threshold that triggers an errored symbol event. · Errored symbol—Number of detected errored symbols in the most recent errored symbol event. · Error running total—Total number of errored symbols. · Event running total—Total number of errored symbol events that have occurred.
OAM local/remote errored frame event	Information about local/remote end errored frame events (available only when local/remote end errored frame events occur): · Event time stamp—Time when an errored frame event occurred. · Errored frame window—Errored frame detection interval. · Errored frame threshold—Errored threshold that triggers an errored frame event. · Errored frame—Number of detected errored frames in the most recent errored frame event. · Error running total—Total number of errored frames. · Event running total—Total number of errored frame events that have occurred.
OAM local/remote errored frame period event	Information about local/remote errored frame period events (available only when local/remote errored frame period events occur): · Event time stamp—Time when an errored frame period event occurred. · Errored frame period window—Errored frame period detection interval. · Errored frame period threshold—Errored threshold that triggers an errored frame period event. · Errored frame period—Number of detected errored frames in the most recent errored frame period event. · Error running total—Total number of errored frames that have detected. · Event running total—Total number of errored frame period events.
OAM local/remote errored frame seconds summary event	Information about local/remote end errored frame seconds events (available only when local/remote end errored frame seconds events occur): · Event time stamp—Time when an errored frame seconds event occurred. · Errored frame second window—Errored frame second detection interval. · Errored Frame seconds threshold—Errored threshold that triggers an errored frame seconds event. · Errored frame seconds—Number of detected errored frame seconds in the most recent errored frame seconds event. · Error running total—Total number of errored frame seconds. · Event running total—Total number of errored frame seconds events that have occurred.

Related commands

reset oam

oam enable

Use oam enable to enable Ethernet OAM.

Use undo oam enable to disable Ethernet OAM.

Syntax

oam enable

undo oam enable

Default

Ethernet OAM is disabled.

Views

Layer 2 Ethernet port view

Predefined user roles

network-admin

Examples

# Enable OAM on Ten-GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] oam enable

oam errored-frame threshold

Use oam errored-frame threshold to set the errored frame event triggering threshold for a port.

Use undo oam errored-frame threshold to restore the default.

Syntax

oam errored-frame threshold threshold-value

undo oam errored-frame threshold

Default

The port uses the global setting.

Views

Layer 2 Ethernet port view

Predefined user roles

network-admin

Parameters

threshold-value: Specifies the errored frame event triggering threshold in number of errored frame seconds, in the range of 0 to 4294967295.

Usage guidelines

The configuration in port view takes effect on the specified port. For a port, the configuration in port view takes precedence.

Examples

# Set the errored frame event triggering threshold to 100.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] oam errored-frame threshold 100

Related commands

· display oam configuration

· display oam link-event

· oam global errored-frame threshold

oam errored-frame window

Use oam errored-frame window to set the errored frame event detection window.

Use undo oam errored-frame window to restore the default.

Syntax

oam errored-frame window window-value

undo oam errored-frame window

Default

The port uses the global setting.

Views

Layer 2 Ethernet port view

Predefined user roles

network-admin

Parameters

window-value: Specifies the errored frame event detection window in the range of 10 to 600 and in steps of 10 (in 100 milliseconds).

Usage guidelines

The configuration in port view takes effect on the specified port. For a port, the configuration in port view takes precedence.

Examples

# Set the errored frame event detection window on Ten-GigabitEthernet 1/0/1 to 2000 milliseconds.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] oam errored-frame window 20

Related commands

· display oam configuration

· display oam link-event

· oam global errored-frame window

oam errored-frame-period threshold

Use oam errored-frame-period threshold to set the errored frame period event triggering threshold on a port.

Use undo oam errored-frame-period threshold to restore the default.

Syntax

oam errored-frame-period threshold threshold-value

undo oam errored-frame-period threshold

Default

The port uses the global setting.

Views

Layer 2 Ethernet port view

Predefined user roles

network-admin

Parameters

threshold-value: Specifies the errored frame period event triggering threshold in the range of 0 to 4294967295.

Usage guidelines

The configuration in port view takes effect on the specified port. For a port, the configuration in port view takes precedence.

Examples

# Set the errored frame period event triggering threshold on Ten-GigabitEthernet 1/0/1 to 100.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] oam errored-frame-period threshold 100

Related commands

· display oam configuration

· display oam link-event

· oam global errored-frame-period threshold

oam errored-frame-period window

Use oam errored-frame-period window to set the errored frame period event detection window.

Use undo oam errored-frame-period window to restore the default.

Syntax

oam errored-frame-period window window-value

undo oam errored-frame-period window

Default

The port uses the global setting.

Views

Layer 2 Ethernet port view

Predefined user roles

network-admin

Parameters

window-value: Specifies the errored frame period event detection window in the range of 1 to 65535. The value of this argument must be a multiple of 10000.

Usage guidelines

The configuration in port view takes effect on the specified port. For a port, the configuration in port view takes precedence.

Examples

# Set the errored frame period event detection window to 20000000.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] oam errored-frame-period window 2000

Related commands

· display oam configuration

· display oam link-event

· oam global errored-frame-period window

oam errored-frame-seconds threshold

Use oam errored-frame-seconds threshold to set the errored frame seconds event triggering threshold on a port.

Use undo oam errored-frame-seconds threshold to restore the default.

Syntax

oam errored-frame-seconds threshold threshold-value

undo oam errored-frame-seconds threshold

Default

The port uses the global setting.

Views

Layer 2 Ethernet port view

Predefined user roles

network-admin

Parameters

threshold-value: Specifies the errored frame seconds event triggering threshold in the range of 0 to 900.

Usage guidelines

The value of the errored frame seconds event triggering threshold cannot be greater than the value of the errored frame seconds event detection window (in seconds). Otherwise, errored frame seconds events cannot be generated.

The configuration in port view takes effect on the specified port. For a port, the configuration in port view takes precedence.

Examples

# Set the errored frame seconds event triggering threshold on Ten-GigabitEthernet 1/0/1 to 100.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] oam errored-frame-seconds threshold 100

Related commands

· display oam configuration

· display oam link-event

· oam errored-frame-seconds window

· oam global errored-frame-seconds threshold

oam errored-frame-seconds window

Use oam errored-frame-seconds window to set the errored frame seconds event detection window.

Use undo oam errored-frame-seconds window to restore the default.

Syntax

oam errored-frame-seconds window window-value

undo oam errored-frame-seconds window

Default

The port uses the global setting.

Views

Layer 2 Ethernet port view

Predefined user roles

network-admin

Parameters

window-value: Specifies the errored frame seconds event detection window in the range of 100 to 9000 and in steps of 10 (in 100 milliseconds).

Usage guidelines

The configuration in port view takes effect on the specified port. For a port, the configuration in port view takes precedence.

Examples

# Set the errored frame seconds event detection window to 10000 milliseconds.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] oam errored-frame-seconds window 100

Related commands

· display oam configuration

· display oam link-event

· oam errored-frame-seconds threshold

· oam errored-frame-seconds period

oam errored-symbol-period threshold

Use oam errored-symbol-period threshold to set the errored symbol event triggering threshold.

Use undo oam errored-symbol-period threshold to restore the default.

Syntax

oam errored-symbol-period threshold threshold-value

undo oam errored-symbol-period threshold

Default

The port uses the global setting.

Views

Layer 2 Ethernet port view

Predefined user roles

network-admin

Parameters

threshold-value: Specifies the errored symbol event triggering threshold in the range of 0 to 4294967295.

Usage guidelines

The configuration in port view takes effect on the specified port. For a port, the configuration in port view takes precedence.

Examples

# Set the errored symbol event triggering threshold to 100.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] oam errored-symbol-period threshold 100

Related commands

· display oam configuration

· display oam link-event

· oam global errored-symbol-period threshold

oam errored-symbol-period window

Use oam errored-symbol-period window to set the errored symbol event detection window.

Use undo oam errored-symbol-period window to restore the default.

Syntax

oam errored-symbol-period window window-value

undo oam errored-symbol-period window

Default

The port uses the global setting.

Views

Layer 2 Ethernet port view

Predefined user roles

network-admin

Parameters

window-value: Specifies the errored symbol event detection window in the range of 1 to 65535. The value of this argument must be a multiple of 1000000.

Usage guidelines

The configuration in port view takes effect on the specified port. For a port, the configuration in port view takes precedence.

Examples

# Set the errored symbol event detection window on Ten-GigabitEthernet 1/0/1 to 200000000.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] oam errored-symbol-period window 200

Related commands

· display oam configuration

· display oam link-event

· oam global errored-symbol-period window

oam global errored-frame threshold

Use oam global errored-frame threshold to set the global errored frame event triggering threshold.

Use undo oam global errored-frame threshold to restore the default.

Syntax

oam global errored-frame threshold threshold-value

undo oam global errored-frame threshold

Default

The errored frame event triggering threshold is 1.

Views

System view

Predefined user roles

network-admin

Parameters

threshold-value: Specifies the errored frame event triggering threshold in the range of 0 to 4294967295.

Usage guidelines

The configuration in system view takes effect on all ports, but has a lower precedence than the configuration in port view.

Examples

# Set the errored frame event triggering threshold to 100.

<Sysname> system-view

[Sysname] oam global errored-frame threshold 100

Related commands

· display oam configuration

· display oam link-event

· oam errored-frame threshold

oam global errored-frame window

Use oam global errored-frame window to set the global errored frame event detection window.

Use undo oam global errored-frame window to restore the default.

Syntax

oam global errored-frame window window-value

undo oam global errored-frame window

Default

The global errored frame event detection window is 1000 milliseconds.

Views

System view

Predefined user roles

network-admin

Parameters

window-value: Specifies the errored frame event detection window in the range of 10 to 600 and in steps of 10 (in 100 milliseconds).

Usage guidelines

The configuration in system view takes effect on all ports, but has a lower precedence than the configuration in port view.

Examples

# Set the errored frame event detection window to 2000 milliseconds.

<Sysname> system-view

[Sysname] oam global errored-frame window 20

Related commands

· display oam configuration

· display oam link-event

· oam errored-frame window

oam global errored-frame-period threshold

Use oam global errored-frame-period threshold to set the global errored frame period event triggering threshold.

Use undo oam global errored-frame-period threshold to restore the default.

Syntax

oam global errored-frame-period threshold threshold-value

undo oam global errored-frame-period threshold

Default

The errored frame period event triggering threshold is 1.

Views

System view

Predefined user roles

network-admin

Parameters

threshold-value: Specifies the errored frame period event triggering threshold in the range of 0 to 4294967295.

Usage guidelines

The configuration in system view takes effect on all ports, but has a lower precedence than the configuration in port view.

Examples

# Set the errored frame period event triggering threshold to 100.

<Sysname> system-view

[Sysname] oam global errored-frame-period threshold 100

Related commands

· display oam configuration

· display oam link-event

· oam errored-frame-period threshold

oam global errored-frame-period window

Use oam global errored-frame-period window to set the global errored frame period event detection window.

Use undo oam global errored-frame-period window to restore the default.

Syntax

oam global errored-frame-period window window-value

undo oam global errored-frame-period window

Default

The global errored frame period event detection window is 10000000.

Views

System view

Predefined user roles

network-admin

Parameters

window-value: Specifies the errored frame period event detection window in the range of 1 to 65535. The value of this argument must be a multiple of 10000.

Usage guidelines

The configuration in system view takes effect on all ports, but has a lower precedence than the configuration in port view.

Examples

# Set the errored frame period event detection window to 20000000.

<Sysname> system-view

[Sysname] oam global errored-frame-period window 2000

Related commands

· display oam configuration

· display oam link-event

· oam errored-frame-period window

oam global errored-frame-seconds threshold

Use oam global errored-frame-seconds threshold to set the global errored frame seconds event triggering threshold.

Use undo oam global errored-frame-seconds threshold to restore the default.

Syntax

oam global errored-frame-seconds threshold threshold-value

undo oam global errored-frame-seconds threshold

Default

The global errored frame seconds event detection interval is 1.

Views

System view

Predefined user roles

network-admin

Parameters

threshold-value: Specifies the errored frame seconds event triggering threshold in the range of 0 to 900.

Usage guidelines

The configuration in system view takes effect on all ports, but has a lower precedence than the configuration in port view.

Examples

# Set the errored frame seconds event triggering threshold to 100.

<Sysname> system-view

[Sysname] oam global errored-frame-seconds threshold 100

Related commands

· display oam configuration

· display oam link-event

· oam errored-frame-seconds threshold

· oam global errored-frame-seconds window

oam global errored-frame-seconds window

Use oam global errored-frame-seconds window to set the global errored frame seconds event detection window.

Use undo oam global errored-frame-seconds window to restore the default.

Syntax

oam global errored-frame-seconds window window-value

undo oam global errored-frame-seconds window

Default

The global errored frame seconds event detection window is 60000 milliseconds.

Views

System view

Predefined user roles

network-admin

Parameters

window-value: Specifies the errored frame seconds event detection window in the range of 100 to 9000 and in steps of 10 (in 100 milliseconds).

Usage guidelines

The configuration in system view takes effect on all ports, but has a lower precedence than the configuration in port view.

Examples

# Set the errored frame seconds event detection window to 10000 milliseconds.

<Sysname> system-view

[Sysname] oam global errored-frame-seconds window 100

Related commands

· display oam configuration

· display oam link-event

· oam errored-frame-seconds period

· oam global errored-frame-seconds threshold

oam global errored-symbol-period threshold

Use oam global errored-symbol-period threshold to set the global errored symbol event triggering threshold.

Use undo oam global errored-symbol-period threshold to restore the default.

Syntax

oam global errored-symbol-period threshold threshold-value

undo oam global errored-symbol-period threshold

Default

The global errored symbol event triggering threshold is 1.

Views

System view

Predefined user roles

network-admin

Parameters

threshold-value: Specifies the errored symbol event triggering threshold in the range of 0 to 4294967295.

Usage guidelines

The configuration in system view takes effect on all ports, but has a lower precedence than the configuration in port view.

Examples

# Set the errored symbol event triggering threshold to 100.

<Sysname> system-view

[Sysname] oam global errored-symbol-period threshold 100

Related commands

· display oam configuration

· display oam link-event

· oam errored-symbol-period threshold

oam global errored-symbol-period window

Use oam global errored-symbol-period window to set the global errored symbol event detection window.

Use undo oam global errored-symbol-period window to restore the default.

Syntax

oam global errored-symbol-period window window-value

undo oam global errored-symbol-period window

Default

The global errored symbol event detection window is 100000000.

Views

System view

Predefined user roles

network-admin

Parameters

window-value: Specifies the errored symbol event detection window in the range of 1 to 65535. The value of this argument must be a multiple of 1000000.

Usage guidelines

The configuration in system view takes effect on all ports, but has a lower precedence than the configuration in port view.

Examples

# Set the errored symbol event detection window to 200000000.

<Sysname> system-view

[Sysname] oam global errored-symbol-period window 200

Related commands

· display oam configuration

· display oam link-event

· oam global errored-symbol-period window

oam global timer hello

Use oam global timer hello to configure the global Ethernet OAM handshake packet transmission interval.

Use undo oam global timer hello to restore the default.

Syntax

oam global timer hello interval

undo oam global timer hello

Default

The global Ethernet OAM handshake packet transmission interval is 1000 milliseconds.

Views

System view

Predefined user roles

network-admin

Parameters

interval: Specifies the Ethernet OAM handshake packet transmission interval, in steps of 100 (in milliseconds). The value range for this argument is 500 to 5000.

Usage guidelines

After the timeout timer of an Ethernet OAM connection expires, the local OAM entity ages out its connection with the peer OAM entity, causing the OAM connection to disconnect. As a best practice to keep the Ethernet OAM connections stable, set the connection timeout timer to be a minimum of five times the handshake packet transmission interval.

The configuration in system view takes effect on all ports, but has a lower precedence than the configuration in port view.

Examples

# Set the Ethernet OAM handshake packet transmission interval to 600 milliseconds.

<Sysname> system-view

[Sysname] oam global timer hello 600

Related commands

· display oam configuration

· oam timer hello

oam global timer keepalive

Use oam global timer keepalive to configure the global Ethernet OAM connection timeout timer.

Use undo oam global timer keepalive to restore the default.

Syntax

oam global timer keepalive interval

undo oam global timer keepalive

Default

The global Ethernet OAM connection timeout timer is 5000 milliseconds.

Views

System view

Predefined user roles

network-admin

Parameters

interval: Specifies the Ethernet OAM connection timeout timer, in steps of 100 (in milliseconds). The value range for this argument is 1000 to 25000.

Usage guidelines

The configuration in system view takes effect on all ports, but has a lower precedence than the configuration in port view.

Examples

# Set the Ethernet OAM connection timeout timer to 6000 milliseconds.

<Sysname> system-view

[Sysname] oam global timer keepalive 6000

Related commands

· display oam configuration

· oam timer keepalive

oam mode

Use oam mode to set the Ethernet OAM mode.

Use undo oam mode to restore the default.

Syntax

oam mode { active | passive }

undo oam mode

Default

An Ethernet OAM-enabled Ethernet port operates in the active Ethernet OAM mode.

Views

Layer 2 Ethernet port view

Predefined user roles

network-admin

Parameters

active: Specifies the active Ethernet OAM mode.

passive: Specifies the passive Ethernet OAM mode.

Usage guidelines

To change the Ethernet OAM mode of an Ethernet OAM-enabled Ethernet port, first disable Ethernet OAM on the port.

Examples

# Disable Ethernet OAM on Ten-GigabitEthernet 1/0/1, and then configure Ten-GigabitEthernet 1/0/1 to operate in passive Ethernet OAM mode.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] undo oam enable

[Sysname-Ten-GigabitEthernet1/0/1] oam mode passive

Related commands

oam enable

oam remote-failure action

Use oam remote-failure action to configure the action the port takes after it receives an Ethernet OAM event from the remote end.

Use undo oam remote-failure action to restore the default.

Syntax

oam remote-failure { connection-expired | critical-event | dying-gasp | link-fault } action error-link-down

undo oam remote-failure { connection-expired | critical-event | dying-gasp | link-fault } action error-link-down

Default

The port only logs the Ethernet OAM event it receives from the remote end.

Views

Layer 2 Ethernet port view

Predefined user roles

network-admin

Parameters

connection-expired: Specifies a connection timeout fault.

critical-event: Specifies a critical fault.

dying-gasp: Specifies a fatal fault.

link-fault: Specifies a link fault.

error-link-down: Terminates the OAM connection, and sets the link state of the port to down.

Examples

# Configure Ten-GigabitEthernet 1/0/1 to terminate the OAM connection after it receives a fatal fault from the remote end, and set the link state of the port to down.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] oam remote-failure dying-gasp action error-link-down

oam remote-loopback

Use oam remote-loopback start to enable Ethernet OAM remote loopback on the specified Ethernet port.

Use oam remote-loopback stop to disable Ethernet OAM remote loopback on the Ethernet port.

Syntax

oam remote-loopback start

oam remote-loopback stop

Default

Ethernet OAM remote loopback is disabled on the Ethernet port.

Views

Layer 2 Ethernet port view

Predefined user roles

network-admin

Usage guidelines

Ethernet OAM remote loopback is available only after the Ethernet OAM connection is established and can be performed only by the Ethernet OAM entities operating in active Ethernet OAM mode.

You can enable Ethernet OAM remote loopback on a specified port in user view or system view, or enable it on the current port in port view. The configurations have the same effect.

Examples

# Configure the active Ethernet OAM mode and enable Ethernet OAM on Ten-GigabitEthernet 1/0/1, and then enable Ethernet OAM remote loopback on Ten-GigabitEthernet 1/0/1 in Layer 2 Ethernet port view.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] oam mode active

[Sysname-Ten-GigabitEthernet1/0/1] oam enable

[Sysname-Ten-GigabitEthernet1/0/1] oam remote-loopback start

Related commands

· oam enable

· oam mode

· oam remote-loopback interface

oam remote-loopback interface

Use oam remote-loopback start interface to enable Ethernet OAM remote loopback on an Ethernet port.

Use oam remote-loopback stop interface to disable Ethernet OAM remote loopback on an Ethernet port.

Syntax

oam remote-loopback start interface interface-type interface-number

oam remote-loopback stop interface interface-type interface-number

Default

Ethernet OAM remote loopback is disabled on an Ethernet port.

Views

User view, system view

Predefined user roles

network-admin

Parameters

interface-type interface-number: Specifies a port by its type and number.

Usage guidelines

Ethernet OAM remote loopback is available only after the Ethernet OAM connection is established and can be performed only by the Ethernet OAM entities operating in active Ethernet OAM mode.

You can enable Ethernet OAM remote loopback on a specified port in user view or system view, or enable it on the current port in port view. The configurations have the same effect.

Examples

# Configure the active Ethernet OAM mode and enable Ethernet OAM on Ten-GigabitEthernet 1/0/1, and then enable Ethernet OAM remote loopback on Ten-GigabitEthernet 1/0/1 in system view.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] oam mode active

[Sysname-Ten-GigabitEthernet1/0/1] oam enable

[Sysname-Ten-GigabitEthernet1/0/1] quit

[Sysname] oam remote-loopback start interface ten-gigabitethernet 1/0/1

Related commands

· oam enable

· oam mode

· oam remote-loopback

oam remote-loopback reject-request

Use oam remote-loopback reject-request to configure a port to reject the Ethernet OAM remote loopback request from a remote port.

Use undo oam remote-loopback reject-request to restore the default.

Syntax

oam remote-loopback reject-request

undo oam remote-loopback reject-request

Default

A port does not reject the Ethernet OAM remote loopback request from a remote port.

Views

Layer 2 Ethernet port view

Predefined user roles

network-admin

Usage guidelines

If a port is in loopback state when you execute the oam remote-loopback reject-request command, the configuration takes effect when the next loopback starts.

Examples

# Configure Ten-GigabitEthernet 1/0/1 to reject the Ethernet OAM remote loopback request from a remote port.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] oam remote-loopback reject-request

oam timer hello

Use oam timer hello to configure the Ethernet OAM handshake packet transmission interval.

Use undo oam timer hello to restore the default.

Syntax

oam timer hello interval

undo oam timer hello

Default

The port uses the global setting.

Views

Layer 2 Ethernet port view

Predefined user roles

network-admin

Parameters

interval: Specifies the Ethernet OAM handshake packet transmission interval, in steps of 100 (in milliseconds). The value range for this argument is 500 to 5000.

Usage guidelines

The configuration in port view takes effect on the specified port. For a port, the configuration in port view takes precedence.

Examples

# Set the Ethernet OAM handshake packet transmission interval to 600 milliseconds.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] oam timer hello 600

Related commands

· display oam configuration

· oam global timer hello

oam timer keepalive

Use oam timer keepalive to configure the Ethernet OAM connection timeout timer.

Use undo oam timer keepalive to restore the default.

Syntax

oam timer keepalive interval

undo oam timer keepalive

Default

The port uses the global setting.

Views

Layer 2 Ethernet port view

Predefined user roles

network-admin

Parameters

interval: Specifies the Ethernet OAM connection timeout timer, in steps of 100 (in milliseconds). The value range for this argument is 1000 to 25000.

Usage guidelines

The configuration in port view takes effect on the specified port. For a port, the configuration in port view takes precedence.

Examples

# Set the Ethernet OAM connection timeout timer to 6000 milliseconds.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] oam timer keepalive 6000

Related commands

· display oam configuration

· oam global timer keepalive

reset oam

Use reset oam to clear the statistics of Ethernet OAM packets and Ethernet OAM link error events for an Ethernet port.

Syntax

reset oam [ interface interface-type interface-number ]

Views

User view

Predefined user roles

network-admin

Parameters

interface interface-type interface-number: Specifies a port by its type and number.

Usage guidelines

If you do not specify the interface keyword, the command clears the statistics of Ethernet OAM packets and Ethernet OAM link error events for all the ports.

Examples

# Clear the statistics of Ethernet OAM packets and Ethernet OAM link error events for all the ports.

<Sysname> reset oam

Related commands

· display oam

· display oam link-event

10-High Availability Command Reference

display oam critical-event

oam errored-frame threshold

oam errored-frame window

oam errored-frame-seconds window

oam errored-symbol-period threshold

oam timer hello

Cloud & AI

InterConnect

Intelligent Terminal Products

Product Support Services

Technical Service Solutions

Resource Center

Policy

Online Help

Become a Partner

Partner Resources

Partner Business Management

Company Information

News & Events

Contact Us