The term "AC" in this document refers to MSR routers that can function as ACs. For more information, see "Compatibility of hardware and AC functionality."

access-control acl

Use access-control acl to specify an ACL for ACL-based access control.

Use undo access-control acl to restore the default.

Syntax

access-control acl acl-number

undo access-control acl

Default

No ACL is specified.

Views

AP view

Service template view

Predefined user roles

network-admin

Parameters

acl-number: Specifies the number of a Layer 2 ACL, in the range of 4000 to 4999.

Usage guidelines

This feature controls client access by using the specified ACL rules. When the device receives an association request, it performs the following actions:

· Allows the client to access the WLAN if the MAC address of the client matches the MAC address attribute or MAC address OUI attribute in a rule and the rule action is permit. If multiple clients match the OUI attribute, all these clients are allowed to access the WLAN.

· Denies the client's access to the WLAN if no match is found or the matched rule has a deny statement.

When you configure this feature, follow these restrictions and guidelines:

· If the specified ACL contains a deny statement, configure a permit statement for the ACL to permit all clients. If you do not do so, no clients can come online.

· ACL-based access control configuration takes precedence over whitelist and blacklist configuration.

· You can specify only one ACL. If you execute this command multiple times, the most recent configuration takes effect.

· The configuration in AP view takes precedence over the configuration in service template view.

Examples

# Create ACL 4000 and create ACL rules to permit the client with MAC address 000e-35b2-000e and clients with the specified OUI. Specify ACL 4000 for service template service1.

<Sysname> system-view

[Syname] acl mac 4000

[Syname-acl-mac-4000] rule 0 permit source-mac 000e-35b2-000e ffff-ffff-ffff

[Syname-acl-mac-4000] rule 1 permit source-mac 000e-35b2-000f ffff-ff00-0000

[Syname-acl-mac-4000] rule 2 deny

[Syname-acl-mac-4000] quit

[Sysname] wlan service-template service1

[Sysname-wlan-st-service1] access-control acl 4000

# Create ACL 4000 and create ACL rules to permit the client with MAC address 000e-35b2-000e and clients with the specified OUI. Specify ACL 4000 for AP ap1.

<Sysname> system-view

[Syname] acl mac 4000

[Syname-acl-mac-4000] rule 0 permit source-mac 000e-35b2-000e ffff-ffff-ffff

[Syname-acl-mac-4000] rule 1 permit source-mac 000e-35b2-000f ffff-ff00-0000

[Syname-acl-mac-4000] rule 2 deny

[Syname-acl-mac-4000] quit

[Sysname] wlan ap ap1 model WA4320i-ACN

[Sysname-wlan-ap-ap1] access-control acl 4000

beacon ssid-hide

Use beacon ssid-hide to disable advertising of the Service Set Identifier (SSID) in beacon frames.

Use undo beacon ssid-hide to restore the default.

Syntax

beacon ssid-hide

undo beacon ssid-hide

Default

The SSID is advertised in beacon frames.

Views

Service template view

Predefined user roles

network-admin

Usage guidelines

This command disables a radio from carrying SSIDs in the beacon frames and responding to probe requests after the specified service template is bound to the radio.

Examples

# Disable advertising the SSID in beacon frames.

<Sysname> system-view

[Sysname] wlan service-template service1

[Sysname-wlan-st-service1] beacon ssid-hide

broadcast-probe reply

Use broadcast-probe reply enable to enable an AP to respond to broadcast probe requests.

Use broadcast-probe reply disable to disable an AP from responding to broadcast probe requests.

Use undo broadcast-probe reply to restore the default.

Syntax

broadcast-probe reply { disable | enable }

undo broadcast-probe reply

Default

In AP view, an AP uses the configuration in AP group view.

In AP group view, an AP responds to broadcast probe requests.

Views

AP view

AP group view

Predefined user roles

network-admin

Usage guidelines

Broadcast probe requests do not carry an SSID. Upon receiving a broadcast probe request, an AP responds with a probe response that carries service information for the AP. To ensure that clients that send unicast probe requests can associate with the AP, disable the AP from responding to broadcast probe requests.

The configuration in AP view takes precedence over the configuration in AP group view.

Examples

# Disable AP ap1 from responding to broadcast probe requests.

<Sysname> system-view

[Sysname] wlan ap ap1 model WA4320i-ACN

[Sysname-wlan-ap-ap1] broadcast-probe reply disable

# Disable APs in AP group group1 from responding to broadcast probe requests.

<Sysname> system-view

[Sysname] wlan ap-group group1

[Sysname-wlan-ap-group-group1] broadcast-probe reply disable

classifier acl

Use classifier acl to configure a forwarding rule for a forwarding policy.

Use undo classifier acl to remove a forwarding rule.

Syntax

classifier acl { acl-number | ipv6 ipv6-acl-number } behavior { local | remote }

undo classifier acl { acl-number | ipv6 ipv6-acl-number }

Default

No forwarding rules are configured.

Views

Forwarding policy view

Predefined user roles

network-admin

Parameters

acl-number: Specifies an IPv4 or Layer 2 ACL number in the range of 2000 to 4999.

ipv6 ipv6-acl-number: Specifies an IPv6 ACL number in the range of 2000 to 3999.

behavior: Specifies a forwarding mode for traffic that matches the specified ACL.

local: Specifies the local forwarding mode.

remote: Specifies the centralized forwarding mode.

Usage guidelines

Actions defined in ACL rules do not take effect in wireless packet forwarding. All matched packets are forwarded based on the forwarding mode.

A forwarding rule takes effect immediately after it is created. You can configure a maximum of 1000 forwarding rules for a forwarding policy.

Examples

# Configure a forwarding rule to locally forward packets that match ACL 2000.

<sysname> system-view

[sysname] wlan forwarding-policy abc

[sysname-wlan-fp-abc] classifier acl 2000 behavior local

client association-location

Use client association-location to enable client association at the AC or APs.

Use undo client association-location to restore the default.

Syntax

client association-location { ac | ap }

undo client association-location

Default

Client association is performed at the AC.

Views

Service template view

Predefined user roles

network-admin

Parameters

ac: Enables client association at the AC.

ap: Enables client association at APs.

Usage guidelines

Make sure the service template is disabled before you execute this command.

Examples

# Enable client association at the AC.

<Sysname> system-view

[Sysname] wlan service-template service1

[Sysname-wlan-st-service1] client association-location ac

client cache aging-time

Use client cache aging-time to set the aging time for the cache of clients.

Use undo client cache aging-time to restore the default.

Syntax

client cache aging-time aging-time

undo client cache aging-time

Default

The aging time for the cache of clients is 180 seconds.

Views

Service template view

Predefined user roles

network-admin

Parameters

aging-time: Specifies the aging time for the cache of clients, in the range of 0 to 86400 seconds.

Usage guidelines

If you set the aging time to 0 seconds, the AC clears the client cache immediately when the clients go offline.

Make sure the service template is disabled before you execute this command.

Examples

# Set the aging time for the cache of clients to 100 seconds.

<Sysname> system-view

[Sysname] wlan service-template service1

[Sysname-wlan-st-service1] client cache aging-time 100

client forwarding-location

Use client forwarding-location to specify the client data traffic forwarder.

Use undo client forwarding-location to restore the default.

Syntax

client forwarding-location { ac | ap [ vlan { start-vlan [ to end-vlan ] } ] }

undo client forwarding-location

Default

The AC forwards client data traffic.

Views

Service template view

Predefined user roles

network-admin

Parameters

ac: Enables the AC to forward client data traffic.

ap: Enables APs to forward client data traffic.

vlan start-vlan to end-vlan: Specifies a VLAN ID range. The value range for the start-vlan and end-vlan arguments is 1 to 4094. If you do not specify this option, APs forward client data traffic from all VLANs.

Usage guidelines

Make sure the service template is disabled before you execute this command.

If APs forward client data traffic, you can specify a VLAN or a VLAN range for the APs to forward client data traffic from the specified VLANs. The AC forwards data traffic from other VLANs.

Make sure client traffic forwarding is enabled when the AC is configured as the client traffic forwarder.

Examples

# Configure APs to forward client data traffic from all VLANs.

<Sysname> system-view

[Sysname] wlan service-template service1

[Sysname-wlan-st-service1] user-forward location ap

client forwarding-policy enable

Use client forwarding-policy enable to enable policy-based forwarding for a service template.

Use undo client forwarding-policy enable to disable policy-based forwarding for a service template.

Syntax

client forwarding-policy enable

undo client forwarding-policy enable

Default

Policy-based forwarding is disabled for a service template.

Views

Service template view

Predefined user roles

network-admin

Usage guidelines

Enable policy-based forwarding for a service template for the following forwarding policies to take effect:

· The forwarding policy applied to the service template.

· The forwarding policy applied to a user profile that uses the service template.

Examples

# Enable policy-based forwarding for service template service1.

<Sysname> system-view

[Sysname] wlan service-template service1

[Sysname-wlan-st-service1] client forwarding-policy enable

Related commands

client-security authentication-location

client forwarding-policy-name

Use client forwarding-policy-name to apply a forwarding policy to a service template.

Use undo client forwarding-policy-name to restore the default.

Syntax

client forwarding-policy-name policy-name

undo client forwarding-policy-name

Default

No forwarding policy is applied to a service template.

Views

Service template view

Predefined user roles

network-admin

Parameters

policy-name: Specifies a forwarding policy by its name, a case-insensitive string of 1 to 31 characters.

Usage guidelines

Make sure the service template is disabled before you execute this command.

For the forwarding policy to take effect, you must enable policy-based forwarding and specify the AC to perform client authentication for the service template.

Make sure the AC and its associated APs are in different network segments.

Examples

# Apply forwarding policy strategy to service template service1.

<Sysname> system-view

[Sysname] wlan service-template service1

[Sysname-wlan-st-service1] client forwarding-policy-name strategy

Related commands

client forwarding-policy enable

client-security authentication-location

client frame-format

Use client frame-format to set the client data frame format.

Use undo client frame-format to restore the default.

Syntax

client frame-format { dot3 | dot11 }

undo client frame-format

Default

Client data frames are encapsulated in 802.3 format.

Views

Service template view

Predefined user roles

network-admin

Parameters

dot3: Specifies the 802.3 format.

dot11: Specifies the 802.11 format.

Usage guidelines

This command takes effect only in centralized forwarding mode.

Make sure the service template is disabled before you execute this command.

Examples

# Configure the client data frames to be encapsulated in 802.11 format.

<Sysname> system-view

[Sysname] wlan service-template service1

[Sysname-wlan-st-service1] client frame-format dot11

Related commands

client forwarding-location

client idle-timeout

Use client idle-timeout to set the client idle timeout timer.

Use undo client idle-timeout to restore the default.

Syntax

client idle-timeout timeout

undo client idle-timeout

Default

In AP view, an AP uses the configuration in AP group view.

In AP group view, the client idle timeout timer is 3600 seconds.

Views

AP view

AP group view

Predefined user roles

network-admin

Parameters

timeout: Specifies the client idle timeout timer in the range of 60 to 86400 seconds.

Usage guidelines

If an online client does not send any frames to the associated AP before the client idle timeout timer expires, the AP logs off the client.

The configuration in AP view takes precedence over the configuration in AP group view.

Examples

# Set the client idle timeout timer to 2000 seconds for AP ap1.

<Sysname> system-view

[Sysname] wlan ap ap1 model WA4320i-ACN

[Sysname-wlan-ap-ap1] client idle-timeout 2000

# Set the client idle timeout timer to 2000 seconds for AP group group1.

<Sysname> system-view

[Sysname] wlan ap-group group1

[Sysname-wlan-ap-group-group1] client idle-timeout 2000

client keep-alive

Use client keep-alive enable to enable client keepalive.

Use client keep-alive disable to disable client keepalive.

Use undo client keep-alive to restore the default.

Syntax

client keep-alive { disable | enable }

undo client keep-alive

Default

In AP view, an AP uses the configuration in AP group view.

In AP group view, client keepalive is disabled.

Views

AP view

AP group view

Predefined user roles

network-admin

Parameters

disable: Disables client keepalive.

enable: Enables client keepalive.

Usage guidelines

This feature enables an AP to send keepalive packets to clients at the client keepalive interval to determine whether the clients are online. If the AP does not receive any replies from a client within three keepalive intervals, it logs off the client.

The configuration in AP view takes precedence over the configuration in AP group view.

Examples

# Enable client keepalive for AP ap1.

<Sysname> system-view

[Sysname] wlan ap ap1 model WA4320i-ACN

[Sysname-wlan-ap-ap1] client keep-alive enable

# Enable client keepalive for AP group group1.

<Sysname> system-view

[Sysname] wlan ap-group group1

[Sysname-wlan-ap-group-group1] client keep-alive enable

Related commands

client keep-alive interval

Use client keep-alive interval to set the client keepalive interval.

Use undo client keep-alive interval to restore the default.

Syntax

client keep-alive interval interval

undo client keep-alive interval

Default

In AP view, an AP uses the configuration in AP group view.

In AP group view, the client keepalive interval is 300 seconds.

Views

AP view

AP group view

Predefined user roles

network-admin

Parameters

interval: Specifies the client keepalive interval in the range of 3 to 1800 seconds.

Usage guidelines

Enable client keepalive before you execute this command.

The configuration in AP view takes precedence over the configuration in AP group view.

Examples

# Set the keepalive interval to 20 seconds for AP ap1.

<Sysname> system-view

[Sysname] wlan ap ap1 model WA4320i-ACN

[Sysname-wlan-ap-ap1] client keep-alive 20

# Set the keepalive interval to 20 seconds for AP group group1.

<Sysname> system-view

[Sysname] wlan ap-group group1

[Sysname-wlan-ap-group-group1] client keep-alive interval 20

Related commands

client keep-alive enable

client max-count

Use client max-count to set the maximum number of associated clients for a service template.

Use undo client max-count to restore the default.

Syntax

client max-count max-number

undo client max-count

Default

The number of associated clients for a service template is not limited.

Views

Service template view

Predefined user roles

network-admin

Parameters

max-number: Specifies the maximum number of clients in the range of 1 to 512.

Usage guidelines

With this feature configured, new clients cannot access the WLAN and the SSID is hidden when the maximum number is reached.

Examples

# Set the maximum number of associated clients to 38 for service template service1.

<Sysname> system-view

[Sysname] wlan service-template service1

[Sysname-wlan-st-service1] client max-count 38

Related commands

beacon ssid-hide

client preferred-vlan authorized

Use client preferred-vlan authorized to configure clients to prefer the authorization VLAN after roaming.

Use undo client preferred-vlan authorized to configure client VLANs to remain unchanged after client roaming.

Syntax

client preferred-vlan authorized

undo client preferred-vlan authorized

Default

Clients prefer the authorization VLAN after roaming.

Views

Service template view

Predefined user roles

network-admin

Usage guidelines

This feature takes effect only on 802.1X and MAC authentication clients.

Typically, the VLAN of a client remains unchanged after client roaming. However, if the client triggers a security alert configured on IMC after roams to another AP, the issued authorization VLAN for user isolation takes effect.

Examples

# Configure clients to prefer the authorization VLAN after roaming.

<Sysname> system-view

[Sysname] wlan service-template service1

[Sysname-wlan-st-service1] client preferred-vlan authorized

client report-mandatory

Use client report-mandatory to allow locally authenticated clients to come online after successful client information reporting.

Use undo client report-mandatory to allow locally authenticated clients to come online immediately after successful local authentication.

Syntax

client report-mandatory

undo client report-mandatory

Default

Locally authenticated clients come online after successful client information reporting.

Views

Service template view

Predefined user roles

network-admin

Usage guidelines

By default, an AP reports information about locally authenticated clients that pass authentication to the AC, and the AC creates client entries and informs the AP to get the clients online. If the CAPWAP tunnel between the AC and the AP operates incorrectly, clients might fail to come online and perform reauthentication repeatedly. To avoid this problem, you can allow clients to come online immediately after successful local authentication so that the AP can forward client traffic when the AC cannot be reached. The AP synchronizes client information to the AC when the tunnel recovers.

Examples

# Allow locally authenticated clients to come online immediately after successful local authentication.

<Sysname> system-view

[Sysname] wlan service-template service1

[Sysname-wlan-st-service1] undo client report-mandatory

client vlan-alloc

Use client vlan-alloc to set the VLAN allocation method for clients.

Use undo client vlan-alloc to restore the default.

Syntax

client vlan-alloc { dynamic | static }

undo client vlan-alloc

Default

The VLAN allocation method for clients is dynamic.

Views

Service template view

Predefined user roles

network-admin

Parameters

dynamic: Specifies dynamic VLAN allocation.

static: Specifies static VLAN allocation.

Usage guidelines

When a client comes online for the first time, the associated AP assigns a random VLAN to it. When the client comes online again, the VLAN assigned to the client depends on the allocation method.

· Static allocation—The client inherits the VLAN that has been assigned to it. If the IP address lease has not expired, the client will use the same IP address. This method helps save IP addresses.

· Dynamic allocation—The radio re-assigns a VLAN to the client. This method balances clients in all VLANs.

Examples

# Set the VLAN allocation method for clients to dynamic.

<Sysname> system-view

[Sysname] wlan service-template service1

[Sysname-wlan-st-service1] client vlan-alloc dynamic

Related commands

service-template

client-statistics-report

Use client-statistics-report enable to enable client statistics reporting.

Use client-statistics-report disable to disable client statistics reporting.

Use undo client-statistics-report to restore the default.

Syntax

client-statistics-report { disable | enable [ interval interval ] }

undo client-statistics-report

Default

In AP view, an AP uses the configuration in AP group view.

In AP group view, client statistics reporting is enabled.

Views

AP view

AP group view

Predefined user roles

network-admin

Parameters

interval interval: Specifies the interval at which client statistics are reported, in the range of 2 to 120 seconds. The interval is 50 seconds by default.

Usage guidelines

This feature enables an AP to report client statistics to the AC at the specified intervals for client entry update. The AC informs the AP to log off a client if the client's information does not exist in the saved entries.

To avoid frequent client re-association, disable this feature when the network is in a bad condition.

The configuration in AP view takes precedence over the configuration in AP group view.

Examples

# Enable client statistics reporting and set the reporting interval to 20 seconds for AP ap1.

<Sysname> system-view

[Sysname] wlan ap ap1 model WA4320i-ACN

[Sysname-wlan-ap-ap1] client-statistics-report enable interval 20

# Enable client statistics reporting and set the reporting interval to 20 seconds for AP group group1.

<Sysname> system-view

[Sysname] wlan ap-group group1

[Sysname-wlan-ap-group-group1] client-statistics-report enable interval 20

customlog format wlan

Use customlog format wlan to enable the device to generate client logs in the specified format.

Use undo customlog format wlan to restore the default.

Syntax

customlog format wlan { normal | sangfor }

undo customlog format wlan

Default

The device generates client logs only in H3C format.

Views

System view

Predefined user roles

network-admin

Parameters

normal: Specifies normal format.

sangfor: Specifies sangfor format.

Usage guidelines

By default, the device generates client logs only in H3C format that logs AP name, radio ID, client MAC address, SSID, BSSID, and client online status.

You can configure the device to generate client logs in one of the following formats:

· Normal—Logs AP MAC address, AP name, client IP address, client MAC address, SSID, and BSSID.

· Sangfor—Logs AP MAC address, client IP address, and client MAC address.

This feature does not affect the generation of client logs in H3C format.

Examples

# Enable the device to generate client logs in sangfor format.

<Sysname> system-view

[Sysname] customlog format wlan sangfor

description

Use description to configure a description for a service template.

Use undo description to restore the default.

Syntax

description text

undo description

Default

No description is configured for a service template.

Views

Service template view

Predefined user roles

network-admin

Parameters

text: Specifies a description, a case-sensitive string of 1 to 64 characters.

Examples

# Configure a description for service template service1.

<Sysname> system-view

[Sysname] wlan service-template service1

[Sysname-wlan-st-service1] description wlanst

display wlan ap all client-number

Use display wlan ap all client-number to display the number of online clients at the 2.4 GHz band and the 5 GHz band.

Syntax

display wlan ap all client-number

Views

Any view

Predefined user roles

network-admin

network-operator

Examples

# Display the number of online clients at both the 2.4 GHz and 5 GHz bands.

<System> display wlan ap all client-number

AP name Clients 2.4GHz 5GHz

ap1 2 2 0

Table 1 Command output

Field	Description
Clients	Total number of online clients.
2.4GHz	Number of online clients at the 2.4 GHz band.
5GHz	Number of online clients at the 5 GHz band.

display wlan ap all radio client-number

Use display wlan ap all radio client-number to display the number of online clients and channel information for each radio.

Syntax

display wlan ap all radio client-number

Views

Any view

Predefined user roles

network-admin

network-operator

Examples

# Display the number of online clients and channel information for each radio.

<Sysname> display wlan ap all radio client-number

AP name RID Channel Clients

ap1 1 44 12

ap1 2 11 4

display wlan ap region-code

Use display wlan ap region-code to display region code information for all APs or the specified AP.

Syntax

display wlan ap { all | name ap-name } region-code

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

all: Specifies all APs.

name ap-name: Specifies an AP by its name, a case-insensitive string of 1 to 64 characters. The string can contain letters, digits, underscores (_), dots (.), left brackets ([), right brackets (]), forward slashes (/), and hyphens (-).

Examples

# Display region code information for all APs.

<Sysname> display wlan ap all region-code

Region Code

AP name Region Code

ap1 CN CHINA

ap2 CN CHINA

ap3 CN CHINA

Table 2 Command output

Field	Description
Region Code	Region code. For more information about region codes, see Table 15.

display wlan ap-group all client-number

Use display wlan ap-group all client-number to display the number of online clients in each radio group.

Syntax

display wlan ap-group all client-number

Views

Any view

Predefined user roles

network-admin

network-operator

Examples

# Display the number of online clients in each radio group.

<Sysname> display wlan ap-group all client-number

AP group name Group ID Clients 2.4GHz 5GHz

default-group 1 150 100 50

1 2 250 50 200

Table 3 Command output

Field	Description
2.4GHz	Number of clients at the 2.4 GHz band.
5GHz	Number of clients at the 5 GHz band.

display wlan blacklist

Use display wlan blacklist to display blacklist entries.

Syntax

display wlan blacklist { dynamic | static }

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

dynamic: Specifies the dynamic blacklist.

static: Specifies the static blacklist.

Examples

# Display static blacklist entries.

<Sysname> display wlan blacklist static

Total number of clients: 3

MAC addresses:

000e-35b2-000e

0019-5b8e-b709

001c-f0bf-9c92

# Display dynamic blacklist entries.

<Sysname> display wlan blacklist dynamic

Total number of clients: 3

MAC address APID Lifetime (s) Duration (hh:mm:ss)

000f-e2cc-0001 1 300 00:02:11

000f-e2cc-0002 2 300 00:01:17

000f-e2cc-0003 3 300 00:02:08

Table 4 Command output

Field	Description
MAC address	Client MAC address.
APID	ID of the AP that detects the rogue client.
Lifetime (s)	Lifetime of the entry in seconds.
Duration (hh:mm:ss)	Duration for the entry since the entry was added to the dynamic blacklist.

display wlan bss

Use display wlan bss to display basic service set (BSS) information.

Syntax

display wlan bss { all | ap ap-name | bssid bssid } [ verbose ]

In IRF mode:

display wlan bss { all | ap ap-name | bssid bssid } [ slot slot-number ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

all: Displays all BSSs.

ap ap-name: Specifies an AP by its name, a case-insensitive string of 1 to 64 characters. The string can contain letters, digits, underscores (_), dots (.), left brackets ([), right brackets (]), forward slashes (/), and hyphens (-).

bssid bssid: Specifies a BSS by its ID. The value is a 48-bit hexadecimal number in the format of H-H-H.

slot slot-number: Specifies an IRF member device by its member ID. If you do not specify a member device, this command displays client information on the master device. (In IRF mode.)

verbose: Displays detailed client information. If you do not specify this keyword, the command displays brief client information.

Examples

# Display brief information about all BSSs.

<Sysname> display wlan bss all

Total number of BSSs: 4

AP name RID SSID BSSID

ap1 1 SSID1 001c-f08f-f804

ap1 2 SSID1 001c-f08f-f806

ap2 1 SSID1 001c-f0bf-9c92

ap2 2 SSID1 001c-f0bf-9c94

# Display detailed information about the BSS with ID 001c-f08f-f804 on member device 1.

<Sysname> display wlan bss bssid 001c-f08f-f804 slot 1 verbose

AP name : ap1

BSSID : 001c-f08f-f804

Radio ID : 1

Service template name : servcie1

SSID : SSID1

VLAN ID : 1

AKM mode : Not configured

User authentication mode : Bypass

Table 5 Command output

Field	Description
AKM mode	AKM mode: · 802.1X. · PSK. · Not configured.
User authentication mode	User authentication mode: · Bypass—No client authentication. · MAC. · 802.1X. · OUI.

Field

Description

AKM mode

AKM mode:

· 802.1X.

· PSK.

· Not configured.

User authentication mode

User authentication mode:

· Bypass—No client authentication.

· MAC.

· 802.1X.

· OUI.

display wlan client

Use display wlan client to display client information.

Syntax

display wlan client [ ap ap-name [ radio radio-id ] | mac-address mac-address | service-template service-template-name | frequency-band { 2.4 | 5 } | vlan vlan-id ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

ap ap-name: Displays information about clients that are connected to the specified AP. The AP name is a case-insensitive string of 1 to 64 characters. The string can contain letters, digits, underscores (_), dots (.), left brackets ([), right brackets (]), forward slashes (/), and hyphens (-).

radio radio-id: Displays information about clients that are connected to the specified radio. The value range for the radio-id argument varies by AP model. If you do not specify this option, the command displays information about all clients that are connected to the specified AP.

mac-address mac-address: Specifies a client by its MAC address.

service-template service-template-name: Displays information about clients that are associated with the specified service template. The service template name is a case-insensitive string of 1 to 63 characters.

frequency-band: Displays information about clients working on the specified band.

2.4: Specifies the 2.4 GHz band.

5: Specifies the 5 GHz band.

verbose: Displays detailed client information. If you do not specify this keyword, the command displays brief client information.

vlan vlan-id: Displays information about clients in the specified VLAN. The VLAN ID is in the range of 1 to 4094.

Examples

# Display brief information about all clients.

<Sysname> display wlan client

Total number of clients: 3

MAC address Username AP name RID IP address VLAN

000f-e265-6400 N/A ap1 1 1.1.1.1 100

000f-e265-6401 user ap2 1 3.0.0.3 200

84db-ac14-dd08 N/A ap1 1 5.5.5.3 1

Table 6 Command output

Field	Description
MAC address	Client MAC address.
Username	Client username: · The field displays the client username if the client uses 802.1X or MAC authentication. · The field displays N/A if the client does not use 802.1X or MAC authentication. NOTE: If the client uses portal authentication, this field does not display the portal username of the client.
AP name	Name of the AP that the client is associated with.
RID	ID of the radio that the client is associated with.
IP address	IPv4 address of the client.
VLAN ID	ID of the VLAN to which the client belongs.

# Display detailed information about the client with MAC address 000f-e265-6400.

<Sysname> display wlan client mac-address 000f-e265-6400 verbose

Total number of clients: 1

MAC address : 000f-e265-6400

IPv4 address : 10.1.1.114

IPv6 address : 2001::1234:5678:0102:0304

Username : N/A

AID : 1

AP ID : 1

AP name : ap1

Radio ID : 1

SSID : office

BSSID : 0026-3e08-1150

VLAN ID : 3

Sleep count : 3

Wireless mode : 802.11gn

Channel bandwidth : 20MHz

SM power save : Enabled

Short GI for 20MHz : Supported

Short GI for 40MHz : Supported

STBC RX capability : Not supported

STBC TX capability : Not supported

LDPC RX capability : Not supported

Block Ack : TID 0 In

Supported HT MCS set : 0, 1, 2, 3, 4, 5, 6, 7,

8, 9, 10, 11, 12, 13, 14,

Supported rates : 1, 2, 5.5, 6, 9, 11,

12, 18, 24, 36, 48, 54 Mbps

QoS mode : WMM

Listen interval : 10

RSSI : 62

Rx/Tx rate : 130/195 Mpbs

Authentication method : Open system

Security mode : PRE-RSNA

AKM mode : Not configured

Cipher suite : N/A

User authentication mode : Bypass

Authorization ACL ID : 3001(Not effective)

Authorization user profile : N/A

Roam status : N/A

Key derivation : SHA1

PMF status : Enabled

Forwarding policy name : Not configured

Online time : 0days 0hours 1minutes 13seconds

FT status : Inactive

Table 7 Command output

Field	Description
MAC address	Client MAC address.
IPv4 address	Client IPv4 address.
IPv6 address	Client IPv6 address.
Username	Client username: · The field displays the client username if the client uses 802.1X or MAC authentication. · The field displays N/A if the client does not use 802.1X or MAC authentication. NOTE: If the client uses portal authentication, this field does not display the portal username of the client.
AID	Association ID.
AP ID	ID of the AP that the client is associated with.
AP name	Name of the AP that the client is associated with.
Radio ID	ID of the radio that the client is associated with.
SSID	SSID with which the client is associated.
VLAN ID	ID of the VLAN to which the client belongs.
Sleep count	Client sleep times.
Wireless mode	Wireless mode: · 802.11a. · 802.11b. · 802.11g. · 802.11gn. · 802.11an. · 802.11ac. · 802.11gac.
Cha nnel bandwidth	Channel bandwidth: · 20 MHz. · 40 MHz. · 80 MHz. · 160 MHz.
20/40 BSS Coexistence Management	Whether the client supports 20/40MHz channel bandwidth coexistence.
SM Power Save	SM Power Save status: · Enabled—Only one antenna of a client operates in active state, and others operate in sleep state to save power. · Disabled.
Short GI for 20MHz	Whether the client supports short GI when its channel bandwidth is 20 MHz: · Supported. · Not supported.
Short GI for 40MHz	Whether the client supports short GI when its channel bandwidth is 40 MHz: · Supported. · Not supported.
Short GI for 80MHz	Whether the client supports short GI when its channel bandwidth is 80 MHz: · Supported. · Not supported.
Short GI for 160/80+80MHz	Whether the client supports short GI when its channel bandwidth is 160 MHz or 80 + 80 MHz: · Supported. · Not supported.
STBC Rx Capability	Client STBC receive capability; · Not Supported. · Supported.
STBC Tx Capability	Client STBC transmission capability: · Not Supported. · Supported.
LDPC Rx capability	Client LDPC receive capability; · Not Supported. · Supported.
SU beamformee capability	Client SU beamformee capability: · Not Supported. · Supported.
MU beamformee capability	Client MU beamformee capability: · Not Supported. · Supported.
Beamformee STS capability	Supported spatial stream quantity if the client is a beamformee receiver, in the range of 0 to 7 (the maximum spatial stream quantity specified by the MIMO mode minus one). This field displays N/A if the client cannot act as a beamformee receiver.
Number of Sounding Dimensions	Supported spatial stream quantity if the client is a beamformee transmitter, in the range of 0 to 7 (the maximum spatial stream quantity specified by the MIMO mode minus one). This field displays N/A if the client cannot act as a beamformee transmitter.
Block Ack	Negotiation result of Block ACK with TID: · TID 0 In—Sends Block ACK for inbound traffic. · TID 0 Out—Sends Block ACK for outbound traffic. · TID 0 Both—Sends Block ACK for both inbound and outbound traffic. · N/A—Does not send Block ACK for both inbound and outbound traffic.
Supported VHT-MCS set	VHT-MCS supported by the client.
Supported HT MCS set	HT-MCS supported by the client.
QoS mode	QoS mode: · N/A—WMM is not supported. · WMM—WMM is supported. WMM information negotiation is carried out between an AP and a client that both support WMM.
Listen interval	Interval at which the client wakes up to listen for beacon frames. It is counted by beacon interval.
RSSI	Received signal strength indication. This value indicates the client signal strength detected by the AP.
Rx/Tx rate	Sending and receiving rates of data, management, and control frames.
Authentication method	Authentication method: · Open system. · Shared key.
Security mode	Security mode: · RSN—Beacons and probe responses carry RSN IE. · WPA—Beacons and probe responses carry WPA IE. · PRE-RSNA—Beacons and probe responses do not carry RSN IE or WPA IE.
AKM mode	AKM mode: · 802.1X. · PSK. · Not configured.
Cipher suite	Cipher suite: · N/A. · WEP40. · WEP104. · WEP128. · CCMP. · TKIP.
User authentication mode	User authentication mode: · Bypass—No client authentication. · MAC. · 802.1X. · OUI.
Authorization ACL ID	Authorized ACL number: · This field displays the ACL number if the authorized ACL takes effect. · This field displays ACL number(Not effective) if the authorized ACL does not take effect. · This field displays N/A if the authentication server is configured without any authorized ACL.
Authorization user profile	Name of the authorized user profile: · This field displays the authorized user profile name if the authorized user profile takes effect. · This field displays authorized user profile name + Not effective if the authorized user profile does not take effect. · This field displays N/A if the authentication server is configured without any authorized user profile.
Roam status	Roam status: · Roaming in progress. · Intra-AC roam. · This field displays N/A if the client stays in one BSS after coming online.
Key derivation	Key derivation type: · SHA1—Uses the HMAC-SHA1 hash algorithm. · SHA256—Uses the HMAC-SHA256 hash algorithm. · N/A—No key derivation algorithm is involved for the authentication type.
PMF status	PMF status: · Enabled—Management frame protection is enabled. · Disabled—Management frame protection is disabled. · N/A—Management frame protection is not involved.
Forwarding policy name	WLAN forwarding policy name: · Not configured. · Policy-name.
Online time	Client online duration.
FT status	This field is not supported in the current software version. Fast BSS transition (FT): · Active—FT is enabled. · Inactive—FT is disabled.

display wlan client ipv6

Use display wlan client ipv6 to display information about client IPv6 addresses.

Syntax

display wlan client ipv6

Views

Any view

Predefined user roles

network-admin

network-operator

Examples

# Display brief status information about the specified client.

<Sysname> display wlan client ipv6

MAC address AP name RID IPv6 address VLAN

84db-ac14-dd08 ap1 1 1::2:0:0:3 300

Table 8 Command output

Field	Description
MAC address	Client MAC address.
RID	Radio ID
IPv6 address	Client IPv6 address.

display wlan client online-duration

Use display wlan client online-duration to display client online duration.

Syntax

display wlan client online-duration [ ap ap-name ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

verbose: Displays detailed information. If you do not specify this keyword, the command displays brief information.

Examples

# Display brief information about client online duration.

<Sysname> display wlan client online-duration

Total number of online clients: 2

MAC address IPv4 address Online duration

a4c1-5b79-fa5b-1d62 192.168.11.123 0days 0hours 2minutes 23seconds

22d3-c5b7-a4b5-96fa 192.168.11.234 0days 0hours 5minutes 34seconds

Table 9 Command output

Field	Description
MAC address	Client MAC address.
IPv4 address	Client IPv4 address.
Online duration	Client online duration.

display wlan client status

Use display wlan client status to display client status information.

Syntax

display wlan client status [ mac-address mac-address ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

mac-address mac-address: Specifies a client by its MAC address in the format of H-H-H. If you do not specify this option, the command displays status information about all clients.

verbose: Displays detailed client status information. If you do not specify this keyword, the command displays brief client status information.

Examples

# Display brief status information about the specified client.

<Sysname> display wlan client status mac-address 001c-f08f-f804

Total number of clients: 1

MAC address Access time RSSI Rx/Tx rate Discard AP name RID

001c-f08f-f804 41ms 0 39/117Mbps 0.00 ap2 2

# Display brief status information about all clients.

<Sysname> display wlan client status

Total number of clients: 2

MAC address Access time RSSI Rx/Tx rate Discard AP name RID

000b-c002-9d09 41ms 65 39/117Mbps 0.00% ap2 2

000f-e265-6401 10ms 62 130/195Mbps 0.00% ap1 1

Table 10 Command output

Field	Description
MAC address	Client MAC address.
Access time	Time the client took to associate with the WLAN.
RSSI	RSSI of the client.
Rx/Tx rate	Rates at which the client receives and sends data, management packets, and control packets.
Discard	Ratio of packets discarded by the client.
AP name	Name of the AP with which the client is associated.
RID	ID of the radio with which the client is associated.

# Display detailed status information about the specified client.

<Sysname> display wlan client status mac-address 001c-f08f-f804 verbose

Total number of clients: 1

MAC address : 001c-f08f-f804

AP name : ap2

Radio ID : 2

Access time : 41 ms

RSSI : 0

Rx/Tx rate : 39/117 Mbps

Received:

Retransmitted packets : 84

Retransmitted packet ratio : 64.12%

Sent:

Retransmitted packets : 0

Retransmitted packet ratio : 0.00%

Discarded:

Discarded packets : 0

Discarded packet ratio : 0.00%

Table 11 Command output

Field	Description
MAC address	Client MAC address.
AP name	Name of the AP that the client is associated with.
Radio ID	ID of the radio that the client is associated with.
Access time	Time the client took to associate with the WLAN.
RSSI	RSSI of the client.
Rx/Tx rate	Rates at which the client receives and sends data, management packets, and control packets.
Received	Received packet statistics: · Retransmitted packets. · Retransmitted packet ratio.
Sent	Sent packet statistics: · Retransmitted packets. · Retransmitted packet ratio.
Discarded	Discarded packet statistics: · Discarded packets. · Discarded packet ratio.

display wlan forwarding-policy

Use display wlan forwarding-policy to display WLAN forwarding policy information.

Syntax

display wlan forwarding-policy [ policy-name ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameter

policy-name: Specifies a WLAN forwarding policy by its name, a case-insensitive string of 1 to 31 characters. If you do not specify this argument, the command displays information about all WLAN forwarding policies.

Examples

# Display information about all WLAN forwarding policies.

<Sysname> display wlan forwarding-policy

Total number of forwarding policies: 2

Forwarding policy name: fwd1

Classifier ACL 2000: Local

Classifier ACL 2004: Local

Classifier IPv6 ACL 2001: Remote

Classifier IPv6 ACL 2002: Remote

Forwarding policy name: fwd2

Classifier ACL 4021: Local

Classifier IPv6 ACL 2000: Remote

Classifier IPv6 ACL 3024: Remote

Table 12 Command output

Field	Description
Classifier ACL number	IPv4 packet forwarding mode: · Local—Local forwarding. · Remote—Centralized forwarding.
Classifier IPv6 ACL number	IPv6 packet forwarding mode: · Local—Local forwarding. · Remote—Centralized forwarding.

Field

Description

Classifier ACL number

IPv4 packet forwarding mode:

· Local—Local forwarding.

· Remote—Centralized forwarding.

Classifier IPv6 ACL number

IPv6 packet forwarding mode:

· Local—Local forwarding.

· Remote—Centralized forwarding.

Related commands

wlan forwarding-policy

display wlan service-template

Use display wlan service-template to display service template information.

Syntax

display wlan service-template [ service-template-name ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

service-template-name: Specifies a service template by its name, a case-insensitive string of 1 to 63 characters. If you do not specify this argument, the command displays information about all service templates.

verbose: Displays detailed service template information.

Examples

# Display brief information about all service templates.

[Sysname] display wlan service-template

Total number of service templates: 2

Service template name SSID Status

1 2333 Enabled

2 3222 Enabled

# Display detailed information about all service templates.

<Sysname> display wlan service-template verbose

Service template name : service1

Description : Not configured

SSID : wuxianfuwu

SSID-hide : Disabled

User-isolation : Disabled

Service template status : Disabled

Maximum clients per BSS : 64

Frame format : Dot3

Seamless roam status : Disabled

Seamless roam RSSI threshold : 50

Seamless roam RSSI gap : 20

VLAN ID : 1

AKM mode : PSK

Security IE : RSN

Cipher suite : CCMP

WEP key ID : 1

TKIP countermeasure time : 100 sec

PTK lifetime : 43200 sec

PTK rekey : Enabled

GTK rekey : Enabled

GTK rekey method : Time-based

GTK rekey time : 86400 sec

GTK rekey client-offline : Enabled

User authentication mode : Bypass

Intrusion protection : Disabled

Intrusion protection mode : Temporary-block

Temporary block time : 180 sec

Temporary service stop time : 20 sec

Fail VLAN ID : 1

802.1X handshake : Enabled

802.1X handshake secure : Disabled

802.1X domain : my-domain

MAC-auth domain : Not configured

Max 802.1X users per BSS : 4096

Max MAC-auth users per BSS : 4096

802.1X re-authenticate : Enabled

Authorization fail mode : Online

Accounting fail mode : Online

Authorization : Permitted

Key derivation : SHA1

PMF status : Optional

Hotspot policy number : Not configured

Forwarding policy status : Disabled

Forwarding policy name : Not configured

Forwarder : AP

FT status : Disabled

QoS trust : Port

QoS priority : 0

Table 13 Command output

Field	Description
SSID	SSID of the service template.
SSID-hide	Whether the SSID is hidden in beacons: · Disabled. · Enabled.
User-isolation	This field is not supported in the current software version. Use isolation: · Disabled. · Enabled.
Service template status	Service template status: · Disabled. · Enabled.
Maximum clients per BSS	Maximum number of clients that the BSS supports.
Frame format	Client data frame encapsulation format: · Dot3—802.3 format. · Dot11—802.11 format.
Seamless roam status	This field is not supported in the current software version. Seamless roaming status: · Disabled. · Enabled.
Seamless roam RSSI threshold	This field is not supported in the current software version. Seamless roaming RSSI threshold.
Seamless roam RSSI gap	This field is not supported in the current software version. Seamless roaming RSSI gap.
VLAN ID	ID of the VLAN to which clients belong after they come online through the service template.
AKM mode	AKM mode: · 802.1X. · PSK.
Security IE	Security IE: · RSN. · WPA.
Cipher suite	Cipher suite: · WEP40. · WEP104. · WEP128. · TKIP. · CCMP.
TKIP countermeasure time	TKIP countermeasure time. The value 0 indicates no countermeasures are taken.
PTK rekey	Whether PTK rekey is enabled: · Enabled. · Disabled.
GTK rekey	Whether GTK rekey is enabled: · Enabled. · Disabled.
GTK rekey method	GTK rekey method: · Time-based. · Packet-based.
GTK rekey time	GTK rekey interval.
GTK rekey packets	Number of packets that can be transmitted before the GTK is refreshed.
GTK rekey client-offline	Whether client-off GTK rekey is enabled: · Enabled. · Disabled.
User authentication mode	Authentication mode: · Bypass—No authentication. · MAC. · MAC-or-802.1X—MAC authentication is performed first. If MAC authentication fails, 802.1X authentication is performed. · 802.1X. · 802.1X-or-MAC—802.1X authentication is performed first. If 802.1X authentication fails, MAC authentication is performed. · OUI-or-802.1X—OUI authentication is performed first. If OUI authentication fails, 802.1X authentication is performed.
Intrusion protection	Whether intrusion protection is enabled: · Enabled. · Disabled.
Intrusion protection mode	Intrusion protection mode: · Temporary-block—Temporarily adds intruders to the block list. · Service-stop—Stops all services provided by the BSS that receives illegal packets until it resets. · Temporary-service-stop—Temporarily stops the access service provided by the BSS that receives illegal packets.
Temporary block time	Temporary block time in seconds.
Temporary service stop time	Temporary service stop time in seconds.
Fail VLAN ID	ID of the VLAN to which clients are added if they cannot pass the authentication when the authentication server can be reached. This field displays Not configured if the fail VLAN ID is not configured.
Critical VLAN ID	ID of the VLAN to which clients are added if they cannot pass the authentication because the authentication server cannot be reached. This field displays Not configured if the critical VLAN ID is not configured.
802.1X handshake	Whether 802.1X handshake is enabled: · Enabled. · Disabled.
802.1X handshake secure	Whether secure 802.1X handshake is enabled: · Enabled. · Disabled.
802.1X domain	802.1X authentication domain. This field displays Not configured if the domain is not configured.
MAC-auth domain	MAC authentication domain. This field displays Not configured if the domain is not configured.
Max 802.1X users per BSS	Maximum number of supported 802.1X users in a BSS.
Max MAC-auth users per BSS	Maximum number of supported users that pass the MAC authentication in a BSS.
802.1X re-authenticate	Whether 802.1X reauthentication is enabled: · Enabled. · Disabled.
Authorization fail mode	Authorization fail mode: · Offline—Clients are logged off when authorization fails. · Online—Clients are not logged off when authorization fails.
Accounting fail mode	Accounting fail mode: · Offline—Clients are logged off when accounting fails. · Online—Clients are not logged off when accounting fails.
Authorization	Authorization information: · Permitted—Applies the authorization information issued by the RADIUS server or the local device. · Ignored—Ignores the authorization information issued by the RADIUS server or the local device.
Key derivation	Key derivation type: · SHA1—Uses the HMAC-SHA1 hash algorithm. · SHA256—Uses the HMAC-SHA256 hash algorithm. · SHA1-AND-SHA256—Uses the HMAC SHA1 and SHA256 hash algorithm.
PMF status	PMF status: · Disabled—Management frame protection is disabled. · Optional—Management frame protection in optional mode is enabled. · Mandatory—Management frame protection in mandatory mode is enabled.
Hotspot policy number	This field is not supported in the current software version. Hotspot 2.0 policy number.
Forwarding policy status	WLAN forwarding policy status: · Disabled. · Enabled.
Forward policy name	WLAN forwarding policy name: · Not configured—No WLAN forwarding policy is configured. · policy-name.
Forwarder	Client traffic forwarder: · AC. · AP.
FT status	This field is not supported in the current software version. FT status: · Disabled. · Enabled.
FT method	This field is not supported in the current software version. FT method: · over-the-air. · over-the-ds.
FT reassociation deadline	This field is not supported in the current software version. FT reassociation timeout timer in seconds.
QoS trust	QoS priority trust mode: · Port—Port priority trust mode. · Dot11e—802.11e priority trust mode.
QoS priority	Port priority in the range of 0 to 7.

‌

display wlan statistics client

Use display wlan statistics client to display client statistics.

Syntax

display wlan statistics client [ mac-address mac-address ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

mac-address mac-address: Specifies a client by its MAC address. If you do not specify this option, the command displays statistics for all clients.

Examples

# Display statistics for all clients.

<Sysname> display wlan statistics client

MAC address : 0014-6c8a-43ff

AP name : ap1

Radio ID : 1

SSID : office

BSSID : 000f-e2ff-7700

RSSI : 31

Sent frames:

Back ground : 0/0 (frames/bytes)

Best effort : 9/1230 (frames/bytes)

Video : 0/0 (frames/bytes)

Voice : 2/76 (frames/bytes)

Received frames:

Back ground : 0/0 (frames/bytes)

Best effort : 18/2437 (frames/bytes)

Video : 0/0 (frames/bytes)

Voice : 7/468 (frames/bytes)

Discarded frames:

Back ground : 0/0 (frames/bytes)

Best effort : 0/0 (frames/bytes)

Video : 0/0 (frames/bytes)

Voice : 5/389 (frames/bytes)

Table 14 Command output

Field	Description
SSID	SSID of the service template.
MAC address	Client MAC address.
Back ground	AC-BK queue.
Best effort	AC-BE queue.
Video	AC-VI queue.
Voice	AC-VO queue.

display wlan statistics connect-history

Use display wlan statistics connect-history to display client connection history.

Syntax

display wlan statistics { ap { all | name ap-name } | service-template service-template-name } connect-history

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

ap: Specifies APs.

all: Specifies all APs.

service-template service-template-name: Specifies a service template by its name.

Examples

# Display the connection history for service template 1.

<Sysname> display wlan statistics service-template 1 connect-history

AP name : ap1

Radio ID : 1

Associations : 132

Association failures : 3

Reassociations : 30

Rejections : 12

Abnormal disassociations : 2

Current associations : 57

# Display the connection history for AP ap1.

<Sysname> display wlan statistics ap name ap1 connect-history

AP name : ap1

Associations : 1

Reassociations : 0

Failures : 0

Rejections : 0

Abnormal disassociations : 0

Current associations : 1

display wlan statistics service template

Use display wlan statistics service-template to display service template statistics.

Syntax

display wlan statistics service-template service-template-name

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

service-template service-template-name: Specifies a service template by its name.

Examples

# Display statistics for service template 1.

<Sysname> display wlan statistics service-template 1

AP name : ap1

Radio ID : 1

Received:

Frame count : 1713

Frame bytes : 487061

Data frame count : 1683

Data frame bytes : 485761

Association request count : 2

Sent:

Frame count : 62113

Frame bytes : 25142076

Data frame count : 55978

Data frame bytes : 22626600

Association response count : 2

display wlan whitelist

Use display wlan whitelist to display whitelist entries.

Syntax

display wlan whitelist

Views

Any view

Predefined user roles

network-admin

network-operator

Examples

# Display whitelist entries.

<Sysname> display wlan whitelist

Total number of clients: 3

MAC addresses:

000e-35b2-000e

0019-5b8e-b709

001c-f0bf-9c92

inherit exclude service-template

Use inherit exclude service-template to configure an AP to not inherit the specified service template from the AP group to which it belongs.

Use undo inherit exclude service-template to restore the default.

Syntax

inherit exclude service-template service-template-name

undo inherit exclude service-template service-template-name

Default

An AP inherits the service template bound to an AP group.

Views

Radio view

Predefined user roles

network-admin

Parameters

service-template-name: Specifies a service template by its name, a case-insensitive string of 1 to 63 characters.

Examples

# Configure AP ap1 to not inherit service template st from an AP group.

<Sysname> system-view

[Sysname] wlan ap ap1

[Sysname-ap-ap1] radio 1

[Sysname-ap-ap1-radio-1] inherit exclude service-template st

map-configuration

Use map-configuration to deploy a configuration file to an AP.

Use undo map-configuration to restore the default.

Syntax

map-configuration filename

undo map-configuration

Default

No configuration file is deployed to an AP.

Views

AP view

AP group's AP model view

Predefined user roles

network-admin

Parameters

filename: Specifies a configuration file by its name, a case-insensitive string of 1 to 63 characters. Make sure the configuration file is stored in the storage medium of the AC.

Usage guidelines

Contents in the configuration file must be complete commands.

The configuration file takes effect when the CAPWAP tunnel to the AC is in Run state. It does not survive an AP reboot.

An AP can only use its main IP address to establish a CAPWAP tunnel to the AC if the AP is configured by using a configuration file.

Examples

# Deploy configuration file downconfig.txt to AP ap1.

<Sysname> system-view

[Sysname] wlan ap ap1 model WA4320i-ACN

[Sysname-wlan-ap-ap1] map-configuration downconfig.txt

# Deploy configuration file downconfig.txt to APs with model WA4320i-ACN in AP group apgroup1.

<Sysname> system-view

[Sysname] wlan ap-group apgroup1

[Sysname-wlan-ap-group-apgroup1] ap-model WA4320i-ACN

[Sysname-wlan-ap-group-apgroup1-ap-model-WA4320i-ACN] map-configuration downconfig.txt

nas-id

Use nas-id to set the network access server identifier (NAS ID).

Syntax

nas-id nas-id

undo nas-id

Default

In AP view, an AP uses the configuration in AP group view. If no configuration exists in AP group view, the AP uses the configuration in global configuration view.

In AP group view, an AP uses the configuration in global configuration view.

In global configuration view, no NAS ID is specified.

Views

AP view

AP group view

Global configuration view

Predefined user roles

network-admin

Parameters

nas-id: Specifies a NAS ID, a case-sensitive string of 1 to 63 characters.

Usage guidelines

After coming online, a client sends a RADIUS request that carries the NAS ID to the RADIUS server to indicate its network access server.

The priorities for the configuration in AP view, AP group view, and global configuration view are in descending order. You can also set the NAS ID when binding a service template to a radio. If you have specified a NAS ID when binding a service template to a radio, the AP uses the NAS ID specified for the service template.

Examples

# Set the NAS ID to abc123 for AP ap1.

<Sysname> system-view

[Sysname] wlan ap ap1 model WA4320i-AGN

[Sysname-wlan-ap-ap1] nas-id abc123

# Set the NAS ID to abc123 for AP group group1.

<Sysname> system-view

[Sysname] wlan ap-group group1

[Sysname-wlan-ap-group-group1] nas-id abc123

# Set the global NAS ID to abc123.

<Sysname> system-view

[Sysname] wlan global-configuration

[Sysname-wlan-global-configuration] nas-id abc123

nas-port-id

Use nas-port-id to set the network access server port identifier (NAS port ID).

Use the undo nas-port-id to restore the default.

Syntax

nas-port-id nas-port-id

undo nas-port-id

Default

In AP view, an AP uses the configuration in AP group view. If no NAS ID is specified in AP group view, the AP uses the configuration in global configuration view.

In AP group view, an AP uses the configuration in global configuration view.

In global configuration view, no NAS port ID is specified.

Views

AP view

AP group view

Global configuration view

Predefined user roles

network-admin

Parameters

nas-port-id: Specifies a NAS port ID, a case-sensitive string of 1 to 63 characters.

Usage guidelines

After coming online, a client sends a RADIUS request that carries the NAS port ID to the RADIUS server to indicate its network access server.

The priorities for the configuration in AP view, AP group view, and global configuration view are in descending order. You can also set the NAS port ID when binding a service template to a radio. If you have specified a NAS port ID when binding a service template to a radio, the AP uses the NAS port ID specified for the service template.

Examples

# Set the NAS port ID to abcd1234 for AP ap1.

<Sysname> system-view

[Sysname] wlan ap ap1 model WA4320i-AGN

[Sysname-wlan-ap-ap1] nas-port-id abcd1234

# Set the NAS port ID to abcd1234 for AP group group1.

<Sysname> system-view

[Sysname] wlan ap-group group1

[Sysname-wlan-ap-group-group1] nas-port-id abcd1234

# Set the global NAS port ID to abcd1234.

<Sysname> system-view

[Sysname] wlan global-configuration

[Sysname-wlan-global-configuration] nas-port-id abcd1234

nas-vlan

Use nas-vlan to set the network access server VLAN identifier (NAS VLAN ID) and enable the AC to encapsulate the VLAN ID in RADIUS requests.

Use undo nas-vlan to restore the default.

Syntax

nas-vlan vlan-id

undo nas-vlan

Default

No NAS VLAN ID is set. Authentication requests sent to the RADIUS server do not contain the NAS VLAN ID field.

Views

AP view

Predefined user roles

network-admin

Parameters

vlan-id: Specifies a NAS VLAN ID in the range of 1 to 4096.

Usage guidelines

When the NAS VLAN ID is set, the AC encapsulates the VLAN ID in RADIUS requests sent to the RADIUS server to indicate clients' network access server.

Set the NAS VLAN ID when a third-party Security Accounting Management (SAM) server is used as the RADIUS server.

Examples

# Set the NAS VLAN ID to 1234 for the AP ap1.

<Sysname> system-view

[Sysname] wlan ap ap1 model WA4320i-ACN

[Sysname-wlan-ap-ap1] nas-vlan 1234

quick-association enable

Use quick-association to enable quick association.

Use undo quick-association to disable quick association.

Syntax

quick-association enable

undo quick-association enable

Default

Quick association is disabled.

Views

Service template view

Predefined user roles

network-admin

Usage guidelines

This command disables APs from performing load balancing or band navigation on clients associated with the specified service template.

Examples

# Enable quick association for service template service1.

<Sysname> system-view

[Sysname] wlan service-template service1

[Sysname-wlan-st-service1]quick-association enable

region-code (AP provision view/AP group provision view)

Use region-code to specify a region code.

Use undo region-code to restore the default.

Syntax

region-code code

undo region-code

Default

In AP provision view, an AP uses the configuration in AP group provision view.

In AP group provision view, no region code is specified.

Views

AP provision view

AP group provision view

Predefined user roles

network-admin

Parameters

code: Specifies a region code. For more information about region codes, see Table 15.

Table 15 Region code information

Country	Code	Country	Code
Andorra	AD	Korea, Republic of Korea	KR
United Arab Emirates	AE	Kenya	KE
Albania	AL	Kuwait	KW
Armenia	AM	Kazakhstan	KZ
Australia	AU	Lebanon	LB
Argentina	AR	Liechtenstein	LI
Australia	AT	Sri Lanka	LK
Azerbaijan	AZ	Lithuania	LT
Bosnia and Herzegovina	BA	Luxembourg	LU
Belgium	BE	Latvia	LV
Bulgaria	BG	Libyan	LY
Bahrain	BH	Morocco	MA
Brunei Darussalam	BN	Monaco	MC
Bolivia	BO	Moldova	MD
Brazil	BR	Macedonia	MK
Bahamas	BS	Macau	MO
Belarus	BY	Martinique	MQ
Belize	BZ	Malta	MT
Canada	CA	Mauritius	MU
Switzerland	CH	Mexico	MX
Cote d'ivoire	CI	Malay Archipelago	MY
Chile	CL	Namibia	NA
China	CN	Nigeria	NG
Colombia	CO	Nicaragua	NI
Costarica	CR	Netherlands	NL
Serbia	RS	Norway	NO
Cyprus	CY	New Zealand	NZ
Czech Republic	CZ	Oman	OM
Germany	DE	Panama	PA
Denmark	DK	Peru	PE
Dominica	DO	Poland	PL
Algeria	DZ	Philippines	PH
Ecuador	EC	Pakistan	PK
Estonia	EE	Puerto Rico	PR
Egypt	EG	Portugal	PT
Spain	ES	Paraguay	PY
Faroe Islands	FO	Qatar	QA
Finland	FI	Romania	RO
France	FR	Russian Federation	RU
Britain	GB	Saudi Arabia	SA
Georgia	GE	Sweden	SE
Gibraltar	GI	Singapore	SG
Greenland	GL	Slovenia	SI
Guadeloupe	GP	Slovak	SK
Greece	GR	San Marino	SM
Guatemala	GT	Salvador	SV
Guyana	GY	Syrian	SY
Honduras	HN	Thailand	TH
Hong Kong	HK	Tunisia	TN
Croatia	HR	Turkey	TR
Hungary	HU	Trinidad and Tobago	TT
Iceland	IS	, Province of China	TW
India	IN	Ukraine	UA
Indonesia	ID	United States of America	US
Ireland	IE	Uruguay	UY
Israel	IL	Uzbekistan	UZ
Iraq	IQ	The Vatican City State	VA
Italy	IT	Venezuela	VE
Iran	IR	Virgin Islands	VI
Jamaica	JM	Vietnam	VN
Jordan	JO	Yemen	YE
Japan	JP	South Africa	ZA
Democratic People's Republic of Korea	KP	Zimbabwe	ZW

Usage guidelines

The region code will take effect after an AP reboots and become invalid after the AP associates with the target AC.

The configuration in AP provision view takes precedence over the configuration in AP group provision view.

Examples

# Specify US as the region code in AP provision view of AP ap1.

<Sysname> system-view

[Sysname] wlan ap ap1 model WA4320i-ACN

[Sysname-wlan-ap-ap1] provision

[Sysname-wlan-ap-ap1-prvs] region-code US

# Specify US as the region code in AP group provision view of AP group group1.

<Sysname> system-view

[Sysname] wlan ap-group group1

[Sysname-wlan-ap-group-group1] provision

[Sysname-wlan-ap-group-group1-prvs] region-code US

region-code (AP view/AP group view/global configuration view)

Use region-code to specify a region code.

Use undo region-code to restore the default.

Syntax

region-code code

undo region-code

Default

In AP view, an AP uses the configuration in AP group view. If no region code is specified in AP group view, the AP uses the configuration in global configuration view.

In AP group view, an AP uses the configuration in global configuration view.

In global configuration view, the region code is CN.

Views

AP view

AP group view

Global configuration view

Predefined user roles

network-admin

Parameters

code: Specifies a region code. For more information about region codes, see Table 15.

Usage guidelines

A region code determines characteristics such as available frequencies, available channels, and transmit power level. Set a valid region code before configuring an AP.

The priorities for the configuration in AP view, AP group view, and global configuration view are in descending order.

Examples

# Specify US as the region code for AP ap1.

<Sysname> system-view

[Sysname] wlan ap ap1 model WA4320i-ACN

[Sysname-wlan-ap-ap1] region-code US

# Specify US as the region code for AP group group1.

<Sysname> system-view

[Sysname] wlan ap-group group1

[Sysname-wlan-ap-group-group1] region-code US

# Specify US as the global region code.

<Sysname> system-view

[Sysname] wlan global-configuration

[Sysname-wlan-global-configuration] region-code US

Related commands

region-code-lock

Use region-code-lock enable to lock the region code.

Use region-code-lock disable to unlock the region code.

Use undo region-code-lock to restore the default.

Syntax

region-code-lock { disable | enable }

undo region-code-lock

Default

In AP view, an AP uses the configuration in AP group view. If no configuration exists in AP group view, the AP uses the configuration in global configuration view.

In AP group view, an AP uses the configuration in global configuration view.

In global configuration view, the region code is not locked.

Views

AP view

AP group view

Global configuration view

Predefined user roles

network-admin

Parameters

A locked region code cannot be changed.

The region-code-lock enable command does not take effect on an AP if you execute this command without specifying a region code first in AP view. The AP's region code is determined by the region code configuration for the AP group to which the AP belongs, or by the global configuration. The same rule applies to an AP group in the same situation.

The priorities for the configuration in AP view, AP group view, and global configuration view are in descending order.

Examples

# Lock the region code for AP ap1.

<Sysname> system-view

[Sysname] wlan ap ap1 model WA4320i-ACN

[Sysname-wlan-ap-ap1] region-code-lock enable

# Lock the region code for AP group group1.

<Sysname> system-view

[Sysname] wlan ap-group group1

[Sysname-wlan-ap-group-group1] region-code-lock enable

# Lock the global region code.

<Sysname> system-view

[Sysname] wlan global-configuration

[Sysname-wlan-global-configuration] region-code-lock enable

Related commands

region-code

reset wlan client

Use reset wlan client to log off a client or all clients.

Syntax

reset wlan client { all | mac-address mac-address }

View

User view

Predefined user roles

network-admin

Parameters

all: Specifies all clients.

mac-address mac-address: Specifies a client by its MAC address.

Examples

# Log off all clients.

<Sysname> reset wlan client all

Related commands

display wlan client

reset wlan dynamic-blacklist

Use reset wlan dynamic-blacklist to remove the specified client or all clients from the dynamic blacklist.

Syntax

reset wlan dynamic-blacklist [ mac-address mac-address ]

Views

User view

Predefined user roles

network-admin

Parameters

mac-address mac-address: Specifies a client by its MAC address. If you do not specify this option, the command removes all clients from the dynamic blacklist.

Examples

# Remove all clients from the dynamic blacklist.

<Sysname> reset wlan dynamic-blacklist

# Remove the specified client from the dynamic blacklist.

<Sysname> reset wlan dynamic-blacklist mac-address b8ca-32a2-df69

Related commands

display wlan blacklist

reset wlan guest-tunnel

Use reset wlan guest-tunnel to delete the specified guest tunnel or all guest tunnels.

Syntax

reset wlan guest-tunnel { all | ip ipv4-address }

View

User view

Predefined user roles

network-admin

Parameters

all: Specifies all guest tunnels.

ip ipv4-address: Specifies a guest tunnel by its peer IPv4 address.

Examples

# Delete all guest tunnels.

<Sysname> reset wlan guest-tunnel all

reset wlan statistics client

Use reset wlan statistics client to clear client statistics.

Syntax

reset wlan statistics client { all | mac-address mac-address }

View

User view

Predefined user roles

network-admin

Parameters

all: Specifies all clients.

mac-address mac-address: Specifies a client by its MAC address.

Examples

# Clear statistics about all clients.

<Sysname> reset wlan statistics client all

Related commands

display wlan statistics

reset wlan statistics service-template

Use reset wlan statistics service-template to clear service template statistics.

Syntax

reset wlan statistics service-template service-template-name

View

User view

Predefined user roles

network-admin

Parameters

service-template-name: Specifies a service template by its name, a case-insensitive string of 1 to 63 characters.

Examples

# Clear statistics about service template service1.

<Sysname> reset wlan statistics service-template service1

Related commands

display wlan statistics

service-template

Use service-template to bind a service template to a radio.

Use undo service-template to unbind a service template from a radio.

Syntax

service-template service-template-name [ nas-id nas-id | nas-port-id nas-port-id ] [ ssid-hide ] [ vlan vlan-id1 | vlan-group vlan-group-name ]

undo service-template service-template-name

Default

In radio view, an AP uses the configuration in AP group view.

In an AP group's radio view, no service template is bound to a radio.

Views

Radio view

AP group's radio view

Predefined user roles

network-admin

Parameters

service-template-name: Specifies a service template by its name, a case-insensitive string of 1 to 63 characters.

nas-id nas-id: Specifies a NAS ID, a case-insensitive string of 1 to 63 characters that do not contain spaces.

nas-port-id nas-port-id: Specifies a NAS port ID, a case-insensitive string of 1 to 63 characters that do not contain spaces.

ssid-hide: Hides SSIDs in beacon frames.

vlan vlan-id1: Specifies a VLAN ID in the range of 1 to 4094.

vlan-group vlan-group-name: Specifies a VLAN group name, a case-insensitive string of 1 to 31 characters. If you do not specify this option, the radio uses the VLAN configured for the service template. For more information about configuring VLAN groups, see VLAN commands in Layer 2—LAN Switching Command Reference.

Usage guidelines

Before you bind a service template to a radio or a radio interface, you must create the service template.

If you specify a non-existent VLAN, the AC creates the VLAN when a client comes online.

The VLAN ID or VLAN group configured using this command takes precedence over the VLAN ID configured for a service template.

The configuration in radio view takes precedence over the configuration in an AP group's radio view.

Examples

# Bind service template service1 to radio 1 and specify VLAN group vg1 for the radio.

<Sysname> system-view

[Sysname] wlan ap ap1

[Sysname-ap-ap1] radio 1

[Sysname-ap-ap1-radio-1] service-template service1 vlan-group vg1

# Bind service template service1 to radio 1 and specify VLAN group vg1 for the radios in AP group apgroup1.

<Sysname> system-view

[Sysname] wlan ap-group apgroup1

[Sysname-wlan-ap-group-apgroup1] ap-model WA4320i-ACN

[Sysname-wlan-ap-group-apgroup1-ap-model-WA4320i-ACN] radio 1

[Sysname-wlan-ap-group-apgroup1-ap-model-WA4320i-ACN-radio-1] service-template service1 vlan-group vg1

service-template enable

Use service-template enable to enable a service template.

Use undo service-template enable to disable a service template.

Syntax

service-template enable

undo service-template enable

Default

A service template is disabled.

Views

Service template view

Predefined user roles

network-admin

Usage guidelines

If the number of BSSs on a device exceeds the limit, you cannot enable a new service template.

Examples

# Enable service template service1.

<Sysname> system-view

[Sysname] wlan service-template service1

[Sysname-wlan-st-service1] service-template enable

snmp-agent trap enable wlan client

Use snmp-agent trap enable wlan client to enable SNMP notification for client access.

Use undo snmp-agent trap enable wlan client to disable SNMP notification for client access.

Syntax

snmp-agent trap enable wlan client

undo snmp-agent trap enable wlan client

Default

SNMP notification is disabled for client access.

Views

System view

Predefined user roles

network-admin

Usage guidelines

When this feature is enabled, the device sends a client status change notification to an NMS every time the status of a client changes. For the notifications to be sent correctly, you must also configure SNMP as described in Network Management and Monitoring Configuration Guide.

Examples

# Enable SNMP notification for client access.

<Sysname> system-view

[Sysname] snmp-agent trap enable wlan client

snmp-agent trap enable wlan client-audit

Use snmp-agent trap enable wlan client-audit to enable SNMP notification for client audit.

Use undo snmp-agent trap enable wlan client-audit to disable SNMP notification for client audit.

Syntax

snmp-agent trap enable wlan client-audit

undo snmp-agent trap enable wlan client-audit

Default

SNMP notification is disabled for client audit.

Views

System view

Predefined user roles

network-admin

Usage guidelines

When this feature is enabled, the device sends a client status change notification to an NMS when a client comes online, goes offline, roams to another AP, or obtains an IP address. For the notifications to be sent correctly, you must also configure SNMP as described in Network Management and Monitoring Configuration Guide.

Examples

# Enable SNMP notification for client audit.

<Sysname> system-view

[Sysname] snmp-agent trap enable wlan client-audit

ssid

Use ssid to set an SSID for a service template.

Use undo ssid to restore the default.

Syntax

ssid ssid-name

undo ssid

Default

No SSID is configured for a service template.

Views

Service template view

Predefined user roles

network-admin

Parameters

ssid-name: Specifies an SSID name, a case-sensitive string of 1 to 32 characters.

Usage guidelines

Disable the service template before you execute this command.

Examples

# Set the SSID to lynn for service template service1.

<Sysname> system-view

[Sysname] wlan service-template service1

[Sysname-wlan-st-service1] ssid lynn

unknown-client

Use unknown-client to set the way that an AP processes traffic from unknown clients.

Use undo unknown-client to restore the default.

Syntax

unknown-client { deauthenticate | drop }

undo unknown-client

Default

An AP drops packets from unknown clients and deauthenticates these clients.

Views

Service template view

Predefined user roles

network-admin

Parameters

deauthenticate: Drops packets from unknown clients and deauthenticates these clients.

drop: Drops packets from unknown clients.

Examples

# Configure APs that use service template example to drop packets from unknown clients but not deauthenticate these clients.

<Sysname> system-view

[Sysname] wlan service-template example

[Sysname-wlan-st-example] unknown-client drop

vlan

Use vlan to assign clients coming online through a service template to the specified VLAN.

Use undo vlan to restore the default.

Syntax

vlan vlan-id

undo vlan

Default

Clients are assigned to VLAN 1 after coming online through a service template.

Views

Service template view

Predefined user roles

network-admin

Parameters

vlan-id: Specifies a VLAN by its VLAN ID, in the range of 1 to 4094. If the specified VLAN does not exist, this command creates the VLAN when clients come online.

Usage guidelines

Disable the service template before you execute this command.

If the specified VLAN does not exist, this command creates the VLAN when clients come online.

Examples

# Assign clients coming online through service template service1 to VLAN 2.

<Sysname> system-view

[Sysname] wlan service-template service1

[Sysname-wlan-st-service1] vlan 2

wlan association optimization

Use wlan association optimization to set the index for optimizing client association ratios.

Use undo wlan association optimization to restore the default.

Syntax

wlan association optimization value

undo wlan association optimization

Default

The index is 0. The device does not optimize client association ratios.

Views

System view

Predefined user roles

network-admin

Parameters

value: Specifies the index for optimizing client association ratios, in the range of 900 to 1000. The smaller the index is, the smaller the calculated association success ratio will be and the larger the calculated congestion ratio and abnormal disassociation ratio will be.

Usage guidelines

This feature enables the device to recalculate the client association success ratio, association congestion ratio, and abnormal disassociation ratio by using the specified index to get smaller ratio values.

The client association success ratio is the number of successful client associations divided by the total number of client association attempts. The client association congestion ratio is the number of failed client associations caused by AP overloading divided by the total number of client association attempts. The client abnormal disassociation ratio is the number of abnormal disassociations divided by the sum of successful associations and online clients.

Examples

# Set the index for optimizing client association ratios to 950.

<Sysname> system-view

[Sysname] wlan association optimization 950

wlan client forwarding enable

Use wlan client forwarding enable to enable client traffic forwarding.

Use undo wlan client forwarding enable to disable client traffic forwarding.

Syntax

wlan client forwarding enable

undo wlan client forwarding enable

Default

Client traffic forwarding is enabled.

Views

System view

Predefined user roles

network-admin

Usage guidelines

You must enable this feature if you configure the AC as the client traffic forwarder.

Examples

# Disable client traffic forwarding.

<Sysname> system-view

[Sysname] undo wlan client forwarding enable

Related commands

client forwarding-location

wlan client forwarding-policy-name

Use wlan client forwarding-policy-name to apply a forwarding policy to a user profile.

Use undo wlan client forwarding-policy-name to restore the default.

Syntax

wlan client forwarding-policy-name policy-name

undo wlan client forwarding-policy-name

Default

No forwarding policy is applied to a user profile.

Views

User profile view

Predefined user roles

network-admin

Parameters

policy-name: Specifies a forwarding policy name, a case-insensitive string of 1 to 31 characters.

Usage guidelines

For the AC to perform policy-based forwarding for clients that use a user profile, apply a forwarding policy to the user profile. After a client passes authentication, the authentication server sends the user profile name specified for the client to the AC. The AC will forward traffic of the client based on the forwarding policy applied to the user profile.

For the forwarding policy applied to a user profile to take effect, perform the following tasks for the service template that the user profile uses:

· Enable policy-based forwarding.

· Specify the AC to perform client authentication.

If you modify or delete the applied forwarding policy, the change takes effect when the client comes online again.

The AC preferentially uses the forwarding policy applied to a user profile to direct client traffic forwarding. If the user profile of a client does not have a forwarding policy applied, the AC uses the forwarding policy applied to the service template.

Make sure the AC and its associated APs are in different network segments.

Examples

# Apply forwarding policy policyname to user profile profilename.

<Sysname> system-view

[Sysname] user-profile profilename

[Sysname-user-profile-profilename] wlan client forward-policy-name policyname

Related commands

client forwarding-policy enable

client-security authentication-location

wlan client reauthentication-period

Use wlan client reauthentication-period to set the idle period before client reauthentication.

Use undo wlan client reauthentication-period to restore the default.

Syntax

wlan client reauthentication-period [ period-value ]

undo wlan client reauthentication-period

Default

The idle period is not configured.

Views

System view

Predefined user roles

network-admin

Parameters

period-value: Specifies the idle period in the range of 1 to 3600 seconds. By default, the idle period is 10 seconds.

Usage guidelines

When URL redirection for WLAN MAC authentication is enabled, an AP redirects clients whose information is not recorded on the RADIUS server to the specified URL for Web authentication. Clients passing Web authentication are logged off and must perform MAC reauthentication to come online. However, MAC reauthentication fails if the IP addresses assigned to the clients have not expired.

Perform this task to add these clients to the dynamic blacklist for the specified idle period after they pass Web authentication to reduce reauthentication failures.

Examples

# Set the idle period before client reauthentication to 100 seconds.

<Sysname> system-view

[Sysname] wlan client reauthentication-period 100

wlan dynamic-blacklist active-on-ap

Use wlan dynamic-blacklist active-on-ap to configure the dynamic blacklist to take effect on APs.

Use undo wlan dynamic-blacklist active-on-ap to configure the dynamic blacklist to take effect on the AC.

Syntax

wlan dynamic-blacklist active-on-ap

undo wlan dynamic-blacklist active-on-ap

Default

The dynamic blacklist takes effect on APs.

Views

System view

Predefined user roles

network-admin

Usage guidelines

If you configure the dynamic blacklist to take effect on the AC, all APs connected to the AC will reject the client in the dynamic blacklist. If you configure the dynamic blacklist to take effect on APs, the AP associated with the client in the dynamic blacklist will reject the client, but the client can still associate with other APs connected to the AC. As a best practice, configure the dynamic blacklist to take effect on the AC in high-density environments.

Examples

# Configure the dynamic blacklist to take effect on the AC.

<Sysname> system-view

[Sysname] undo wlan dynamic-blacklist active-on-ap

wlan dynamic-blacklist lifetime

Use wlan dynamic-blacklist lifetime to set the aging time for dynamic blacklist entries.

Use undo wlan dynamic-blacklist lifetime to restore the default.

Syntax

wlan dynamic-blacklist lifetime lifetime

undo wlan dynamic-blacklist lifetime

Default

The aging time is 300 seconds for dynamic blacklist entries.

Views

System view

Predefined user roles

network-admin

Parameters

lifetime: Specifies the aging time in the range of 1 to 3600 seconds.

Usage guidelines

The configured aging time takes effect only on entries added to the dynamic blacklist after this command is executed.

The aging time for dynamic blacklist entries only applies to rogue client entries.

Examples

# Set the aging time for dynamic blacklist entries to 3600 seconds.

<Sysname> system-view

[Sysname] wlan dynamic-blacklist lifetime 3600

wlan forwarding-policy

Use wlan forwarding-policy to create a forwarding policy and enter its view, or enter the view of an existing forwarding policy.

Use undo wlan forwarding-policy to delete a forwarding policy.

Syntax

wlan forwarding-policy policy-name

undo wlan forwarding-policy policy-name

Default

No forwarding policies are created.

Views

System view

Predefined user roles

network-admin

Parameters

policy-name: Specifies a forwarding policy name, a case-insensitive string of 1 to 31 characters.

Usage guidelines

Actions defined in ACL rules do not take effect in wireless packet forwarding. All matched packets are forwarded based on the forwarding mode.

You can create a maximum of 1000 forwarding policies.

Examples

# Create forwarding policy abc and enter its view.

<Sysname> system-view

[Sysname] wlan forwarding-policy abc

[Sysname-wlan-fp-abc]

wlan link-test

Use wlan link-test to test wireless link quality.

Syntax

wlan link-test mac-address

Views

Any view

Predefined user roles

network-admin

Parameters

mac-address: Specifies the client MAC address in the H-H-H format.

Usage guidelines

Wireless link quality detection enables an AP to test the quality of the link to a wireless client. The AP sends empty data frames to the client at each supported rate. Then it calculates link quality information such as RSSI, packet retransmissions, and RTT based on the responses from the client.

The timeout timer for wireless link quality detection is 10 seconds. If wireless link detection is not completed within the timeout timer, test results cannot be obtained.

Examples

# Test the quality of the wireless link to the client with MAC address 60a4-4cda-eff0.

<Sysname> wlan link-test 60a4-4cda-eff0

Testing link to 60a4-4cda-eff0. Press CTRL + C to break.

Link Status

-----------------------------------------------------------------------

MAC address: 60a4-4cda-eff0

-----------------------------------------------------------------------

VHT-MCS Rate(Mbps) Tx packets Rx packets RSSI Retries RTT(ms)

-----------------------------------------------------------------------

NSS = 1

-----------------------------------------------------------------------

0 32.5 5 5 54 0 0

1 65 5 5 51 0 0

2 97.5 5 5 49 0 0

3 130 5 5 47 0 0

4 195 5 5 45 0 0

5 260 5 5 45 0 0

6 292.5 5 5 44 0 0

7 325 5 5 44 0 0

8 390 5 5 44 0 0

9 433.3 5 5 43 0 0

-----------------------------------------------------------------------

NSS = 2

-----------------------------------------------------------------------

0 65 5 5 44 0 0

1 130 5 5 44 0 0

2 195 5 5 44 0 0

3 260 5 5 44 0 0

4 390 5 5 44 0 0

5 520 5 5 44 0 0

6 585 5 5 43 0 0

7 650 5 5 43 0 0

8 780 5 5 43 0 0

9 866.7 5 5 43 0 0

# Test the quality of the wireless link to the client with MAC address 60a4-4cda-eff0.

<Sysname> wlan link-test 784f-43b6-077c

Testing link to 784f-43b6-077c. Press CTRL + C to break.

Link Status

-----------------------------------------------------------------------

MAC address: 784f-43b6-077c

-----------------------------------------------------------------------

MCS Rate(Mbps) Tx packets Rx packets RSSI Retries RTT(ms)

-----------------------------------------------------------------------

0 6.5 5 5 54 0 0

1 13 5 5 51 0 0

2 19.5 5 5 49 0 0

3 26 5 5 47 0 0

4 39 5 5 45 0 0

5 52 5 5 45 0 0

6 58.5 5 5 44 0 0

7 72.2 5 5 44 0 0

8 13 5 5 44 0 0

9 26 5 5 43 0 0

10 39 5 5 44 0 0

11 52 5 5 44 0 0

12 78 5 5 44 0 0

13 104 5 5 44 0 0

14 117 5 5 44 0 0

15 144.4 5 5 44 11 0

-----------------------------------------------------------------------

Table 16 Command output

Field	Description
No./MCS/VHT-MCS	· No.—Rate number for link quality test on 802.11a, 802.11b, or 802.11g clients. · MCS—MCS index for link quality test on 802.11n clients. · VHT-MCS—VHT-MCS index for link quality test on 802.11ac clients.
Rate(Mbps)	Rate at which the AP sends wireless link quality detection frames.
Tx packets	Number of wireless link quality detection frames sent by the AP.
Rx packets	Number of responses received by the AP.
RSSI	RSSI of the client detected by the AP.
Retries	Number of wireless link quality retransmission frames sent by the AP.
RTT(ms)	Round trip time for link quality test frames from the AP to the client.
NSS	Number of spatial streams for link quality test on 802.11n or 802.11ac clients.

wlan permit-ap-group

Use wlan permit-ap-group to specify a permitted AP group for client association.

Use undo permit-ap-group to delete a permitted AP group.

Syntax

wlan permit-ap-group ap-group-name

undo wlan permit-ap-group [ ap-group-name ]

Default

No permitted AP group is specified for client association.

Views

User profile view

Predefined user roles

network-admin

Parameters

ap-group-name: Specifies an AP group by its name, a case-insensitive string of 1 to 31 characters.

Usage guidelines

If no permitted AP group is specified for client association, client access is not restricted.

If you specify a permitted AP group for client association, clients can only associate with APs in the AP group.

The undo form of the command deletes all permitted AP groups if you do not specify the ap-group-name argument.

Examples

# Specify AP group group1 as the permitted AP group for client association.

<Sysname> system-view

[Sysname] user-profile profile1

[Sysname-user-profile-profile1] wlan permit-ap-group group1

wlan permit-ssid

Use wlan permit-ssid to specify a permitted SSID for client association.

Use undo permit-ssid to delete a permitted SSID.

Syntax

wlan permit-ssid ssid-name

undo wlan permit-ssid [ ssid-name ]

Default

No permitted SSID is specified for client association.

Views

User profile view

Predefined user roles

network-admin

Parameters

ssid-name: Specifies an SSID by its name, a case-sensitive string of 1 to 32 characters.

Usage guidelines

If no permitted SSID is specified for client association, client association is not restricted.

If you specify a permitted SSID for client association, clients can only associate with WLANs through the SSID.

The undo form of the command deletes all permitted SSIDs if you do not specify the ssid-name argument.

Examples

# Specify SSID ssid1 as the permitted SSID for client access.

<Sysname> system-view

[Sysname] user-profile profile1

[Sysname-user-profile- profile1] wlan permit-ssid ssid1

wlan service-template

Use wlan service-template to create a service template and enter its view, or enter the view of an existing service template.

Use undo wlan service-template to delete a service template.

Syntax

wlan service-template service-template-name

undo wlan service-template service-template-name

Default

No service template exists.

Views

System view

Predefined user roles

network-admin

Parameters

service-template-name: Specifies a service template by its name, a case-insensitive string of 1 to 63 characters.

Usage guidelines

You cannot delete a service template that has been bound to a radio.

Examples

# Create service template service1 and enter its view.

<Sysname> system-view

[Sysname] wlan service-template service1

wlan static-blacklist mac-address

Use wlan static-blacklist mac-address to add a client to the static blacklist.

Use undo wlan static-blacklist mac-address to remove a client from the static blacklist.

Syntax

wlan static-blacklist mac-address mac-address

undo wlan static-blacklist [ mac-address mac-address ]

Default

No clients exist in the static blacklist.

Views

System view

Predefined user roles

network-admin

Parameters

mac-address mac-address: Specifies a client by its MAC address in the format of H-H-H.

Usage guidelines

If you add an online client to the static blacklist, the command logs off the client.

You cannot add a client to both the whitelist and the static blacklist.

The undo form of the command removes all clients from the static blacklist if you do not specify the mac-address mac-address option.

Do not add multicast or broadcast MAC addresses to the static blacklist.

Examples

# Add MAC address 001c-f0bf-9c92 to the static blacklist.

<Sysname> system-view

[Sysname] wlan static-blacklist mac-address 001c-f0bf-9c92

Related commands

display wlan blacklist

wlan web-server api-path

Use wlan web-server api-path to specify the path of the Web server to which client information is reported.

Use undo wlan web-server api-path to restore the default.

Syntax

wlan web-server api-path path

undo wlan web-server api-path

Default

The path of the Web server is not specified.

Views

System view

Predefined user roles

network-admin

Parameters

path: Specifies a path, a case-sensitive string of 1 to 256 characters.

Usage guidelines

The Web server accepts client information only when the server's host name, port number, and path are specified.

If you execute this command multiple times, the most recent configuration takes effect.

Examples

# Specify the path of the Web server as /wlan/dev-cfg.

<Sysname> system-view

[Sysname] wlan web-server api-path /wlan/dev-cfg

Related commands

wlan web-server host

wlan web-server max-client-entry

wlan web-server host

Use wlan web-server host to specify the host name and port number of the Web server to which client information is reported.

Use undo wlan web-server host to restore the default.

Syntax

wlan web-server host host-name port port-number

undo wlan web-server host

Default

The host name and port number of the Web server are not specified.

Views

System view

Predefined user roles

network-admin

Parameters

host host-name: Specifies a host name, a case-insensitive string of 3 to 127 characters that can contain letters, digits, hyphens (-), underscores (_), and dots (.).

port port-number: Specifies a port number in the range of 1 to 65534.

Usage guidelines

The Web server accepts client information only when the server's host name, port number, and path are specified.

Client information changes are reported to the Web server in real time.

If you execute this command multiple times, the most recent configuration takes effect.

Examples

# Specify the host name and port number of the Web server as www.abc.com and 668, respectively.

<Sysname> system-view

[Sysname] wlan web-server host www.abc.com port 668

Related commands

wlan web-server api-path

wlan web-server max-client-entry

Use wlan web-server max-client-entry to set the maximum number of client entries that can be reported at a time.

Use undo wlan web-server max-client-entry to restore the default.

Syntax

wlan web-server max-client-entry number

undo wlan web-server max-client-entry

Default

A maximum of ten client entries can be reported at a time.

Views

System view

Predefined user roles

network-admin

Parameters

number: Specifies a maximum number of client entries that can be reported at a time, in the range of 1 to 25.

Examples

# Set the maximum of client entries that can be reported at a time to 12.

<Sysname> system-view

[Sysname] wlan web-server max-client-entry 12

Related commands

wlan web-server api-path

wlan web-server host

wlan whitelist mac-address

Use wlan whitelist mac-address to add a client to the whitelist.

Use undo wlan whitelist mac-address to remove a client from the whitelist.

Syntax

wlan whitelist mac-address mac-address

undo wlan whitelist [ mac-address mac-address ]

Default

No clients exist in the whitelist.

Views

System view

Predefined user roles

network-admin

Parameters

mac-address mac-address: Specifies a client by its MAC address in the format of H-H-H.

Usage guidelines

When you add the first client to the whitelist, the system asks you whether to disconnect all online clients. Enter Y at the prompt to configure the whitelist.

If you remove an online client from the whitelist, the command logs off the client. If you remove all clients from the whitelist, online clients will not be logged off.

You cannot add a client to both the whitelist and the static blacklist.

The undo form of the command removes all clients from the whitelist if you do not specify the mac-address mac-address option.

Do not add multicast or broadcast MAC addresses to the whitelist.

Examples

# Add MAC address 001c-f0bf-9c92 to the whitelist.

<Sysname> system-view

[Sysname] wlan whitelist mac-address 001c-f0bf-9c92

This command will disconnect all clients. Continue? [Y/N]:

Related commands

display wlan whitelist

15-WLAN Command Reference (AC)

region-code (AP view/AP group view/global configuration view)

Intelligent Terminal Products

Product Support Services

Technical Service Solutions

Resource Center

Policy

Online Help

Become a Partner

Partner Policy & Program

Global Learning

Partner Sales Resources

Service Business

News & Events

Contact Us