Table of Contents

Related Documents

03-Data buffer commands

Title	Size	Download
03-Data buffer commands	96.11 KB

Data buffer commands

Inappropriate data buffer changes can cause system problems. Before manually changing data buffer settings, make sure you understand its impact on your device. As a best practice, use the burst-mode enable command if the system requires large buffer spaces. The burst-mode enable command and the buffer apply command are mutually exclusive. If you have configured the data buffer by using one command, you must execute the undo form of the command before using the other command.

buffer apply

Use buffer apply to apply manually configured data buffer settings.

Use undo buffer apply to restore the default.

Syntax

buffer apply

undo buffer apply

Views

System view

Predefined user roles

network-admin

Usage guidelines

For data buffer settings to take effect, you must execute this command after configuring data buffer settings.

After applying manually configured data buffer settings, you cannot directly modify the applied settings. To modify them, you must cancel the application, reconfigure data buffer settings, and reapply the new settings.

This command might cause the PFC function to be on longer in effect or to operate incorrectly. For information about PFC configuration commands, see Ethernet interface commands in Layer 2—LAN Switching Command Reference.

Examples

# Apply manually configured data buffer settings.

<Sysname> system-view

[Sysname] buffer apply

buffer packet-drop alarm enable

Use buffer packet-drop alarm enable to enable packet-drop alarms.

Use undo buffer packet-drop alarm enable to disable packet-drop alarms.

Syntax

buffer packet-drop alarm enable

undo buffer packet-drop alarm enable

Default

Packet-drop alarms are disabled.

Views

System view

Predefined user roles

network-admin

Usage guidelines

The device generates and reports packet-drop alarms to a network management system (such as IMC) for displaying the data buffer usage.

This command does not take effect only on the Headroom buffer.

Examples

# Enable packet-drop alarms.

<Sysname> system-view

[Sysname] buffer packet-drop alarm enable

Related commands

buffer usage threshold queue (interface view)

buffer usage threshold queue (system view)

buffer packet-drop alarm interval

Use buffer packet-drop alarm interval to set the interval for sending packet-drop alarms.

Use undo buffer packet-drop alarm interval to restore the default.

Syntax

buffer packet-drop alarm interval interval

undo buffer packet-drop alarm interval

Default

The interval for sending packet-drop alarms is 5 seconds.

Views

System view

Predefined user roles

network-admin

Parameters

interval: Specifies the interval for sending packet-drop alarms, in the range of 0 to 60 seconds. The value of 0 indicates that packet-drop alarms are sent immediately after they are generated.

Usage guidelines

This command takes effect only when packet-drop alarms are enabled.

Examples

# Set the interval for sending packet-drop alarms to 20 seconds.

<Sysname> system-view

[Sysname] buffer packet-drop alarm interval 20

Related commands

buffer packet-drop alarm enable

buffer queue guaranteed

Use buffer queue guaranteed to set the fixed-area space for a queue.

Use undo buffer queue guaranteed to delete the fixed-area space setting of a queue.

Syntax

In standalone mode:

buffer egress [ slot slot-number ] cell queue queue-id guaranteed ratio ratio

undo buffer egress [ slot slot-number ] cell queue queue-id guaranteed

In IRF mode:

buffer egress [ chassis chassis-number slot slot-number ] cell queue queue-id guaranteed ratio ratio

undo buffer egress [ chassis chassis-number slot slot-number ] cell queue queue-id guaranteed

Default

The fixed-area ratio for a queue is 13%.

Views

System view

Predefined user roles

network-admin

Parameters

egress: Specifies the egress buffer.

slot slot-number: Specifies a card by its slot number. If you do not specify a card, this command applies to all cards. (In standalone mode.)

chassis chassis-number slot slot-number: Specifies a card on an IRF member device. The chassis-number argument represents the ID of the IRF member device. The slot-number argument represents the slot number of the card. If you do not specify this option, the command applies to all cards of the IRF fabric. (In IRF mode.)

cell: Specifies cell resources.

queue-id: Specifies a queue by its ID in the range of 0 to 7.

ratio ratio: Specifies the fixed-area space ratio, in percentage. The value range for ratio is 1 to 100.

Usage guidelines

By default, all queues have an equal share of the fixed area. You can set the fixed-area ratio for a queue. The other queues equally share the remaining part.

The fixed-area space for a queue cannot be used by other queues. Therefore, it is also called the minimum guaranteed buffer for the queue. The sum of fixed-area space configured for all queues cannot exceed the total fixed-area space. Otherwise, the configuration fails.

Examples

# Configure queue 0 to use 20% fixed-area space of cell resources in the egress buffer.

<Sysname> system-view

[Sysname] buffer egress cell queue 0 guaranteed ratio 20

buffer queue shared

Use buffer queue shared to set the maximum shared-area ratio for a queue.

Use undo buffer queue shared to delete the maximum shared-area ratio setting of a queue.

Syntax

In standalone mode:

buffer egress [ slot slot-number ] cell queue queue-id shared ratio ratio

undo buffer egress [ slot slot-number ] cell queue queue-id shared

In IRF mode:

buffer egress [ chassis chassis-number slot slot-number ] cell queue queue-id shared ratio ratio

undo buffer egress [ chassis chassis-number slot slot-number ] cell queue queue-id shared

Default

The maximum shared-area ratio for a queue is 20%.

Views

System view

Predefined user roles

network-admin

Parameters

egress: Specifies the egress buffer.

slot slot-number: Specifies a card by its slot number. If you do not specify a card, this command applies to all cards. (In standalone mode.)

cell: Specifies cell resources.

queue-id: Specifies a queue by its ID in the range of 0 to 7.

ratio ratio: Specifies the maximum shared-area space ratio, in percentage. The value range for ratio is 0 to 100.

Usage guidelines

By default, all queues have an equal share of the shared area. You can set the shared-area ratio for a queue. The unconfigured queues use the default setting. The shared-area space for each queue is finally determined by the chip based on your configuration and the number of packets to be received and sent.

Examples

# Configure queue 0 to use up to 10% shared-area space of cell resources in the egress buffer.

<Sysname> system-view

[Sysname] buffer egress cell queue 0 shared ratio 10

buffer threshold alarm enable

Use buffer threshold alarm enable to enable threshold-crossing alarms.

Use undo buffer threshold alarm enable to disable threshold-crossing alarms.

Syntax

buffer threshold alarm { egress | headroom | ingress } enable

undo buffer threshold alarm { egress | headroom | ingress } enable

Default

Threshold-crossing alarms are disabled.

Views

System view

Predefined user roles

network-admin

Parameters

ingress: Specifies the ingress buffer.

headroom: Specifies the Headroom buffer.

egress: Specifies the egress buffer.

Usage guidelines

The device generates and reports threshold-crossing alarms to a network management system (such as IMC) for displaying the data buffer usage.

Examples

# Enable threshold-crossing alarms.

<Sysname> system-view

[Sysname] buffer threshold alarm ingress enable

Related commands

buffer usage threshold headroom

buffer usage threshold headroom queue

buffer usage threshold queue (interface view)

buffer usage threshold queue (system view)

buffer threshold alarm interval

Use buffer threshold alarm interval to set the interval for sending threshold-crossing alarms.

Use undo buffer threshold alarm interval to restore the default.

Syntax

buffer threshold alarm { egress | headroom | ingress } interval interval

undo buffer threshold alarm { egress | headroom | ingress } interval

Default

The interval for sending threshold-crossing alarms is 5 seconds.

Views

System view

Predefined user roles

network-admin

Parameters

ingress: Specifies the ingress buffer.

headroom: Specifies the Headroom buffer.

egress: Specifies the egress buffer.

interval: Specifies the interval for sending threshold-crossing alarms, in the range of 0 to 60 seconds. 0 indicates that threshold-crossing alarms are sent immediately after they are generated.

Usage guidelines

This command takes effect only when threshold-crossing alarms are enabled.

Examples

# Set the interval for sending threshold-crossing alarms to 20 seconds.

<Sysname> system-view

[Sysname] buffer threshold alarm ingress interval 20

Related commands

buffer threshold alarm enable

buffer usage threshold headroom

buffer usage threshold headroom queue

buffer usage threshold queue (interface view)

buffer usage threshold queue (system view)

buffer total-shared

Use buffer total-shared to set the total shared-area ratio.

Use undo buffer total-shared to delete the total shared-area ratio setting.

Syntax

In standalone mode:

buffer egress [ slot slot-number ] cell total-shared ratio ratio

undo buffer egress [ slot slot-number ] cell total-shared

In IRF mode:

buffer egress [ chassis chassis-number slot slot-number ] cell total-shared ratio ratio

undo buffer egress [ chassis chassis-number slot slot-number ] cell total-shared

Default

The total shared-area ratio is 100%.

Views

System view

Predefined user roles

network-admin

Parameters

egress: Specifies the egress buffer.

slot slot-number: Specifies a card by its slot number. If you do not specify a card, this command applies to all cards. (In standalone mode.)

cell: Specifies cell resources.

ratio ratio: Specifies the ratio of the shared area, in percentage. The value range for ratio is 0 to 100.

Usage guidelines

After you set the shared-area ratio, the remaining buffer space is automatically assigned to the fixed area.

Examples

# Configure the shared area to use 50% space of cell resources in the egress buffer.

<Sysname> system-view

[Sysname] buffer egress cell total-shared ratio 50

buffer usage threshold

Use buffer usage threshold to set a per-interface buffer usage threshold.

Use undo buffer usage threshold to restore the default.

Syntax

In standalone mode:

buffer usage threshold slot slot-number ratio ratio

undo buffer usage threshold slot slot-number

In IRF mode:

buffer usage threshold chassis chassis-number slot slot-number ratio ratio

undo buffer usage threshold chassis chassis-number slot slot-number

Default

The per-interface buffer usage threshold is 100%.

Views

System view

Predefined user roles

network-admin

Parameters

slot slot-number: Specifies a card by its slot number. (In standalone mode.)

chassis chassis-number slot slot-number: Specifies a card on an IRF member device. The chassis-number argument represents the member ID of the IRF member device. The slot-number argument represents the slot number of the card. (In IRF mode.)

ratio ratio: Specifies the buffer usage threshold in percentage, in the range of 1 to 100.

Usage guidelines

After you configure this command, the switch automatically records buffer usage for each interface. When a queue on an interface uses more buffer space than the set threshold, the system counts one threshold violation for the queue.

To display the buffer usage statistics for interfaces, use the display buffer usage interface command.

Examples

# (In standalone mode.) Set the per-interface buffer usage threshold to 50% for card 3.

<Sysname> system-view

[Sysname] buffer usage threshold slot 3 ratio 50

# (In IRF mode.) Set the per-interface buffer usage threshold to 50% for card 3 on IRF member device 2.

<Sysname> system-view

[Sysname] buffer usage threshold chassis 2 slot 3 ratio 50

Related commands

display buffer usage interface

buffer usage threshold headroom

Use buffer usage threshold headroom to set the global per-queue alarm threshold for the Headroom buffer.

Use undo buffer usage threshold headroom to restore the default.

Syntax

In standalone mode:

buffer usage threshold headroom slot slot-number ratio ratio

undo buffer usage threshold headroom slot slot-number ratio

In IRF mode:

buffer usage threshold headroom chassis chassis-number slot slot-number ratio ratio

undo buffer usage threshold headroom chassis chassis-number slot slot-number ratio

Default

The global per-queue alarm threshold for the Headroom buffer is 100%.

Views

System view

Predefined user roles

network-admin

Parameters

slot slot-number: Specifies a card by its slot number. (In standalone mode.)

ratio ratio: Specifies the alarm threshold in percentage, in the range of 1 to 100.

Usage guidelines

This command takes effect only when threshold-crossing alarms are enabled. When a queue exceeds the global alarm threshold for the Headroom buffer, the device generates and reports a threshold-crossing alarm to a network management system (such as IMC).

Examples

# (In standalone mode.) Set the global per-queue alarm threshold to 50% for slot 1.

<Sysname> system-view

[Sysname] buffer usage threshold headroom slot 1 ratio 50

# (In IRF mode.) Set the global per-queue alarm threshold to 50% for slot 2 in chassis 1.

<Sysname> system-view

[Sysname] buffer usage threshold headroom chassis 1 slot 2 ratio 50

Related commands

buffer threshold alarm enable

buffer usage threshold headroom queue

Use buffer usage threshold headroom queue to set the Headroom buffer alarm threshold for a queue on an interface.

Use undo buffer usage threshold headroom queue to restore the default.

Syntax

buffer usage threshold headroom queue queue-id ratio ratio

undo buffer usage threshold headroom queue queue-id ratio

Default

The global per-queue alarm threshold for the Headroom buffer is used.

Views

Interface view

Predefined user roles

network-admin

Parameters

queue-id: Specifies a queue by its ID in the range of 0 to 7.

ratio ratio: Specifies the alarm threshold in percentage, in the range of 1 to 100.

Usage guidelines

This command takes effect only when threshold-crossing alarms are enabled. When a queue exceeds the alarm threshold, the device generates and reports a threshold-crossing alarm to a network management system (such as IMC).

Examples

# Set the Headroom buffer alarm threshold to 50% for queue 1 on HundredGigE 1/0/1.

<Sysname> system-view

[Sysname] interface hundredgige 1/0/1

[Sysname–HundredGigE1/0/1] buffer usage threshold headroom queue 1 ratio 50

Related commands

buffer threshold alarm enable

buffer usage threshold queue (interface view)

Use buffer usage threshold queue to set the ingress or egress buffer alarm threshold for a queue on an interface.

Use undo buffer usage threshold queue to restore the default.

Syntax

buffer { egress | ingress } usage threshold queue queue-id ratio ratio

undo buffer { egress | ingress } usage threshold queue queue-id ratio

Default

The global per-queue alarm threshold for the ingress or egress buffer is used.

Views

Interface view

Predefined user roles

network-admin

Parameters

ingress: Specifies the ingress buffer.

egress: Specifies the egress buffer.

queue-id: Specifies a queue by its ID in the range of 0 to 7.

ratio ratio: Specifies the alarm threshold in percentage, in the range of 1 to 100.

Usage guidelines

This command takes effect only when threshold-crossing alarms are enabled. When a queue exceeds the alarm threshold for the ingress or egress buffer, the device generates and reports a threshold-crossing alarm to a network management system (such as IMC).

Examples

# Set the ingress buffer alarm threshold to 50% for queue 1 on HundredGigE 1/0/1.

<Sysname> system-view

[Sysname] interface hundredgige 1/0/1

[Sysname–HundredGigE1/0/1] buffer ingress usage threshold queue 1 ratio 50

Related commands

buffer threshold alarm enable

buffer usage threshold queue (system view)

Use buffer usage threshold queue to set the global ingress or egress buffer alarm threshold for a queue.

Use undo buffer usage threshold queue to restore the default.

Syntax

In standalone mode:

buffer { egress | ingress } usage threshold slot slot-number queue queue-id ratio ratio

undo buffer { egress | ingress } usage threshold slot slot-number queue queue-id ratio

In IRF mode:

buffer { egress | ingress } usage threshold chassis chassis-number slot slot-number queue queue-id ratio ratio

undo buffer { egress | ingress } usage threshold chassis chassis-number slot slot-number queue queue-id ratio

Default

The global ingress or egress buffer alarm threshold for a queue is 100%.

Views

System view

Predefined user roles

network-admin

Parameters

ingress: Specifies the ingress buffer.

egress: Specifies the egress buffer.

slot slot-number: Specifies a card by its slot number. (In standalone mode.)

queue-id: Specifies a queue by its ID in the range of 0 to 7.

ratio ratio: Specifies the alarm threshold in percentage, in the range of 1 to 100.

Usage guidelines

This command takes effect only when threshold-crossing alarms are enabled. When a queue exceeds the global ingress or egress alarm threshold, the device generates and reports a threshold-crossing alarm to a network management system (such as IMC).

Examples

# (In standalone mode.) Set the global ingress alarm threshold to 50% for queue 1 in slot 1.

<Sysname> system-view

[Sysname] buffer ingress usage threshold slot 1 queue 1 ratio 50

# (In IRF mode.) Set the global ingress alarm threshold to 50% for queue 1 in slot 2 of chassis 1.

<Sysname> system-view

[Sysname] buffer ingress usage threshold chassis 1 slot 2 queue 1 ratio 50

Related commands

buffer threshold alarm enable

burst-mode enable

Use burst-mode enable to enable the Burst feature.

Use undo burst-mode enable to disable the Burst feature.

Syntax

In standalone mode:

burst-mode enable

undo burst-mode enable

Default

The Burst feature is disabled.

Views

System view

Predefined user roles

network-admin

Usage guidelines

The Burst feature is especially useful for reducing packet losses under the following circumstances:

· Broadcast or multicast traffic is intensive, resulting in bursts of traffic.

· Traffic enters a device from a high-speed interface and goes out of a low-speed interface.

· Traffic enters a device from multiple same-rate interfaces and goes out of an interface with the same rate.

The default data buffer settings are changed after the Burst feature is enabled. You can display the data buffer settings by using the display buffer command.

Disabling the Burst feature after enabling it might cause the PFC function to be on longer in effect or to operate incorrectly. For information about PFC configuration commands, see Ethernet interface commands in Layer 2—LAN Switching Command Reference.

Examples

# Enable the Burst feature.

<Sysname> system-view

[Sysname] burst-mode enable

display buffer

Use display buffer to display buffer size settings.

Syntax

In standalone mode:

display buffer [ slot slot-number ] [ queue [ queue-id ] ]

In IRF mode:

display buffer [ chassis chassis-number slot slot-number ] [ queue [ queue-id ] ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

slot slot-number: Specifies a card by its slot number. If you do not specify a card, this command displays buffer size settings for all cards. (In standalone mode.)

chassis chassis-number slot slot-number: Specifies a card on an IRF member device. The chassis-number argument represents the ID of the IRF member device. The slot-number argument represents the slot number of the card. If you do not specify this option, the command displays buffer size settings for all cards of the IRF fabric. (In IRF mode.)

queue queue-id: Specifies a queue by its number in the range of 0 to 7. If you specify a queue, this command displays the fixed-area ratio and shared-area ratio for the specified queue. If you specify the queue keyword without the queue-id argument, this command displays the fixed-area ratio and shared-area ratio for each queue. If you do not specify the queue keyword, this command displays the total shared-area ratio.

Examples

# (In standalone mode.) Display buffer size settings.

<Sysname> display buffer

Slot Type Eg(Total-shared)

1 cell 100

Eg: Size of the sending buffer

Total-shared: Size of the shared buffer for all ports

Unit: Ratio

# (In standalone mode.) Display the fixed-area ratio and shared-area ratio for the queues.

<Sysname> display buffer queue

Slot Queue Type Eg(Guaranteed , Shared)

1 0-7 cell -- , --

2 0-7 cell 13 , 20

Eg: Size of the sending buffer

Guaranteed: Size of the minimum guaranteed buffer per queue

Shared: Size of the maximum shared buffer per queue

Unit: Ratio

# (In IRF mode.) Display buffer size settings for slot 2 in chassis 1.

<Sysname> display buffer chassis 1 slot 5

Slot Type Eg(Total-shared)

1/5 cell 100

Eg: Size of the sending buffer

Total-shared: Size of the shared buffer for all ports

Unit: Ratio

# (In IRF mode.) Display the fixed-area ratio and shared-area ratio for the queues for slot 2 in chassis 1.

<Sysname> display buffer chassis 1 slot 5 queue

Slot Queue Type Eg(Guaranteed , Shared)

1/5 0,2-7 cell 13 , 20

1/5 1 cell 13 , 50

Eg: Size of the sending buffer

Guaranteed: Size of the minimum guaranteed buffer per queue

Shared: Size of the maximum shared buffer per queue

Unit: Ratio

Table 1 Command output

Field	Description
Type	Resource type.
Queue	Queue ID in the range of 0 to 7.
Eg	Egress buffer.
(Total-shared)	Total-shared indicates the total shared-area ratio. If the device does not support a resource type, this field displays two hyphens (--).
(Guaranteed , Shared)	· Guaranteed indicates the fixed-area ratio of a queue. If the device does not support a resource type, this field displays two hyphens (--). · Shared indicates the shared-area ratio of a queue. If the device does not support a resource type, this field displays two hyphens (--).

display buffer usage

Use display buffer usage to display buffer usage.

Syntax

In standalone mode:

display buffer usage [ slot slot-number ]

In IRF mode:

display buffer usage [ chassis chassis-number slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

slot slot-number: Specifies a card by its slot number. If you do not specify a card, this command displays buffer usage for all cards. (In standalone mode.)

chassis chassis-number slot slot-number: Specifies a card on an IRF member device. The chassis-number argument represents the ID of the IRF member device. The slot-number argument represents the slot number of the card. If you do not specify this option, the command displays buffer usage for all cards of the IRF fabric. (In IRF mode.)

Examples

# Display buffer usage.

<Sysname> display buffer usage

Egress total-shared cell buffer usage on slot 1 :

Unit 0 :

XPE 0

Total: 32678 KB

Used: 0 KB

Free: 32678 KB

Global_headroom: 0 KB

SP_headroom_used: 0 KB

SP_buffer_used: 0 KB

SP_Headroom_peak: 0 KB

5sec 1min 5min

------------------------------------------------------------------

HGE5/0/1 XPE 0 0% 0% 0%

HGE5/0/2 XPE 0 0% 0% 0%

HGE5/0/3 XPE 0 0% 0% 0%

HGE5/0/4 XPE 0 0% 0% 0%

HGE5/0/5 XPE 0 0% 0% 0%

HGE5/0/6 XPE 0 0% 0% 0%

HGE5/0/7 XPE 0 0% 0% 0%

HGE5/0/8 XPE 0 0% 0% 0%

HGE5/0/10 XPE 0 0% 0% 0%

Unit 1 :

XPE 0

Total: 32678 KB

Used: 0 KB

Free: 32678 KB

Global_headroom: 0 KB

SP_headroom_used: 0 KB

SP_buffer_used: 0 KB

SP_Headroom_peak: 0 KB

HGE5/0/9 XPE 0 0% 0% 0%

HGE5/0/11 XPE 0 0% 0% 0%

HGE5/0/12 XPE 0 0% 0% 0%

HGE5/0/13 XPE 0 0% 0% 0%

HGE5/0/14 XPE 0 0% 0% 0%

HGE5/0/15 XPE 0 0% 0% 0%

HGE5/0/16 XPE 0 0% 0% 0%

HGE5/0/17 XPE 0 0% 0% 0%

HGE5/0/18 XPE 0 0% 0% 0%

Unit 2 :

XPE 0

Total: 32678 KB

Used: 0 KB

Free: 32678 KB

Global_headroom: 0 KB

SP_headroom_used: 0 KB

SP_buffer_used: 0 KB

SP_Headroom_peak: 0 KB

HGE5/0/19 XPE 0 0% 0% 0%

HGE5/0/20 XPE 0 0% 0% 0%

HGE5/0/21 XPE 0 0% 0% 0%

HGE5/0/22 XPE 0 0% 0% 0%

HGE5/0/23 XPE 0 0% 0% 0%

HGE5/0/24 XPE 0 0% 0% 0%

HGE5/0/25 XPE 0 0% 0% 0%

HGE5/0/26 XPE 0 0% 0% 0%

HGE5/0/27 XPE 0 0% 0% 0%

Unit 3 :

XPE 0

Total: 32678 KB

Used: 0 KB

Free: 32678 KB

Global_headroom: 0 KB

SP_headroom_used: 0 KB

SP_buffer_used: 0 KB

SP_Headroom_peak: 0 KB

HGE5/0/28 XPE 0 0% 0% 0%

HGE5/0/29 XPE 0 0% 0% 0%

HGE5/0/30 XPE 0 0% 0% 0%

HGE5/0/31 XPE 0 0% 0% 0%

HGE5/0/32 XPE 0 0% 0% 0%

HGE5/0/33 XPE 0 0% 0% 0%

HGE5/0/34 XPE 0 0% 0% 0%

HGE5/0/35 XPE 0 0% 0% 0%

HGE5/0/36 XPE 0 0% 0% 0%

Table 2 Command output

Field	Description
Egress total-shared cell buffer usage on slot	Usage of cell resources in the shared area on an IRF member device.
Unit	Chip number.
XPE	Type of the data buffer.
Total	Total size of the data buffer.
Used	Size of used data buffer.
Free	Size of free data buffer.
5sec	Percentage of the buffer that the port uses for the last 5 seconds.
1min	Percentage of the buffer that the port uses for the last 1 minute.
5min	Percentage of the buffer that the port uses for the last 5 minutes.

‌

display buffer usage interface

Use display buffer usage interface to display buffer usage statistics for interfaces.

Syntax

display buffer usage interface [ interface-type [ interface-number ] ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

interface-type [ interface-number ]: Specifies an interface by its type and number. If you do not specify the interface-type argument, this command displays buffer usage statistics for all Ethernet interfaces. If you specify the interface-type argument without the interface-number argument, this command displays buffer usage statistics for all Ethernet interfaces of the specified type.

verbose: Displays detailed buffer usage statistics. If you do not specify this keyword, the command displays brief buffer usage statistics.

Examples

# Display brief buffer usage statistics for HundredGigE 1/0/1.

<Sysname> display buffer usage interface hundredgige 1/0/1

Interface QueueID Total Used Threshold(%) Violations

--------------------------------------------------------------------------------

HGE1/0/1 0 5437952 0 100 0

1 5437952 0 100 0

2 5437952 0 100 0

3 5437952 0 100 0

4 5437952 0 100 0

5 5437952 0 100 0

6 5437952 0 100 0

7 5437952 0 100 0

Table 3 Command output

Field	Description
Total	Data buffer size in bytes allowed for a queue.
Used	Data buffer size in bytes that has been used by a queue.
Threshold(%)	Buffer usage threshold for a queue. The threshold value is the same as the per-interface threshold value.
Violations	Number of threshold violations for a queue. The value of this field is reset upon a switch reboot.

‌

# Display detailed buffer usage statistics for HundredGigE 1/0/1.

[Sysname] display buffer usage interface hundredgige 1/0/1 verbose

HundredGigE1/0/1

Ingress:

QueueID: 0

Total: 127974 Used: 0 Threshold(%): 70

Violations: 0 Shared: 0 Headroom: 0

XoffThres: 127968 IsDynamic: 0

Used(%): 0 Free: 127968 UsedPeak: 0

HeadroomUsed(%): 0 HeadroomFree: 0 HeadroomPeak: 0

QueueID: 1

Total: 127974 Used: 0 Threshold(%): 70

Violations: 0 Shared: 0 Headroom: 0

XoffThres: 127968 IsDynamic: 0

Used(%): 0 Free: 127968 UsedPeak: 0

HeadroomUsed(%): 0 HeadroomFree: 0 HeadroomPeak: 0

QueueID: 2

Total: 127974 Used: 0 Threshold(%): 70

Violations: 0 Shared: 0 Headroom: 0

XoffThres: 127968 IsDynamic: 0

Used(%): 0 Free: 127968 UsedPeak: 0

HeadroomUsed(%): 0 HeadroomFree: 0 HeadroomPeak: 0

QueueID: 3

Total: 127974 Used: 0 Threshold(%): 70

Violations: 0 Shared: 0 Headroom: 0

XoffThres: 127968 IsDynamic: 0

Used(%): 0 Free: 127968 UsedPeak: 0

HeadroomUsed(%): 0 HeadroomFree: 0 HeadroomPeak: 0

QueueID: 4

Total: 127974 Used: 0 Threshold(%): 70

Violations: 0 Shared: 0 Headroom: 0

XoffThres: 127968 IsDynamic: 0

Used(%): 0 Free: 127968 UsedPeak: 0

HeadroomUsed(%): 0 HeadroomFree: 0 HeadroomPeak: 0

QueueID: 5

Total: 127974 Used: 0 Threshold(%): 70

Violations: 0 Shared: 0 Headroom: 0

XoffThres: 127968 IsDynamic: 0

Used(%): 0 Free: 127968 UsedPeak: 0

HeadroomUsed(%): 0 HeadroomFree: 0 HeadroomPeak: 0

QueueID: 6

Total: 127974 Used: 0 Threshold(%): 70

Violations: 0 Shared: 0 Headroom: 0

XoffThres: 127968 IsDynamic: 0

Used(%): 0 Free: 127968 UsedPeak: 0

HeadroomUsed(%): 0 HeadroomFree: 0 HeadroomPeak: 0

QueueID: 7

Total: 127974 Used: 0 Threshold(%): 70

Violations: 0 Shared: 0 Headroom: 0

XoffThres: 127968 IsDynamic: 0

Used(%): 0 Free: 127968 UsedPeak: 0

HeadroomUsed(%): 0 HeadroomFree: 0 HeadroomPeak: 0

Egress:

QueueID: 0