vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. The specified VPN instance must already exist.

ip-address: Specifies the IP address of the default next hop. If you do not specify the vpn-instance vpn-instance-name option, the default next hop belongs to the public network.

direct: Specifies a directly connected default next hop.

track track-entry-number: Specifies a track entry by its number in the range of 1 to 1024.

&<1-2>: Indicates that the argument before it can be entered up to two times.

Usage guidelines

You can specify multiple default next hops for backup in one command line or by executing this command multiple times.

With a default next hop specified, the undo apply default-next-hop command removes the default next hop.

Without any default next hop specified, the undo apply default-next-hop command removes all default next hops.

Examples

# Set a directly-connected default next hop of 1.1.1.1.

<Sysname> system-view

[Sysname] policy-based-route aa permit node 11

[Sysname-pbr-aa-11] apply default-next-hop 1.1.1.1 direct

apply next-hop

Use apply next-hop to set next hops.

Use undo apply next-hop to remove next hops.

Syntax

apply next-hop [ vpn-instance vpn-instance-name ] { ip-address [ direct ] [ track track-entry-number ] }&<1-2>

undo apply next-hop [ [ vpn-instance vpn-instance-name ] ip-address&<1-2> ]

Default

No next hop is set.

Views

Policy node view

Predefined user roles

network-admin

mdc-admin

Parameters

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. The specified VPN instance must already exist.

ip-address: Specifies the IP address of the next hop. If you do not specify the vpn-instance vpn-instance-name option, the next hop belongs to the public network.

direct: Specifies that the next hop must be directly connected to take effect.

track track-entry-number: Specifies a track entry by its number in the range of 1 to 1024.

&<1-2>: Indicates that the argument before it can be entered up to two times.

Usage guidelines

You can specify multiple next hops for backup in one command line or by executing this command multiple times.

With a next hop specified, the undo apply next-hop command removes the next hop.

Without any next hop specified, the undo apply next-hop command removes all next hops.

Examples

# Set a directly-connected next hop of 1.1.1.1.

<Sysname> system-view

[Sysname] policy-based-route aa permit node 11

[Sysname-pbr-aa-11] apply next-hop 1.1.1.1 direct

apply output-interface

Use apply output-interface to set output interfaces.

Use undo apply output-interface to remove output interfaces.

Syntax

apply output-interface { interface-type interface-number [ track track-entry-number ] }

undo apply output-interface [ { interface-type interface-number } ]

Default

No output interface is set.

Views

Policy node view

Predefined user roles

network-admin

mdc-admin

Parameters

interface-type interface-number: Specifies an interface by its type and number.

track track-entry-number: Specifies a track entry by its number in the range of 1 to 1024.

Usage guidelines

You can specify only null interfaces as the output interfaces.

Examples

# Specify Null 0 as the output interface for IP packets.

<Sysname> system-view

[Sysname] policy-based-route aa permit node 11

[Sysname-pbr-aa-11] apply output-interface NULL 0

apply precedence

Use apply precedence to set a precedence for IP packets.

Use undo apply precedence to restore the default.

Syntax

apply precedence { type | value }

undo apply precedence

Default

No precedence is set for IP packets.

Views

Policy node view

Predefined user roles

network-admin

mdc-admin

Parameters

type: Specifies the precedence type for IP packets.

value: Specifies the precedence for IP packets. Eight precedence values (0 to 7) are available. Each precedence value corresponds to a precedence type, as shown in Table 1. You can set either a precedence value or a precedence type for IP packets.

Table 1 IP precedences and corresponding types

Precedence value	Precedence type
0	routine
1	priority
2	immediate
3	flash
4	flash-override
5	critical
6	internet
7	network

Examples

# Set the precedence to 5 (critical) for IP packets.

<Sysname> system-view

[Sysname] policy-based-route aa permit node 11

[Sysname-pbr-aa-11] apply precedence critical

apply service-chain

Use apply service-chain to set the service chain information.

Use undo apply service-chain to restore the default.

Syntax

apply service-chain path-id service-path-id [ path-index service-patch-index ]

undo apply service-chain

Default

No service chain information is set.

Views

Policy node view

Predefined user roles

network-admin

mdc-admin

Parameters

path-id service-path-id: Specifies a service chain by its path ID in the range of 1 to 16777215. The path ID uniquely identifies a service chain.

path-index service-path-index: Specifies a node in a service chain by its index in the range of 1 to 255. This option is used to distinguish different nodes in a service chain. If all packets are sent from one node, you do not need to specify this option.

Examples

# Set service chain path ID 1 and node index 10.

<Sysname> system-view

[Sysname] policy-based-route aa permit node 5

[Sysname-pbr-aa-5] apply service-chain path-id 1 path-index 10

description

Use description to configure a description for a policy node.

Use undo description to restore the default.

Syntax

description text

undo description

Default

No description is configured for a policy node.

Views

Policy node view

Predefined user roles

network-admin

mdc-admin

Parameters

text: Specifies a description, a case-sensitive string of 1 to 127 characters.

Examples

# Configure the description as Officeuse for policy node 1.

<Sysname> system-view

[Sysname] policy-based-route 1 permit node 1

[Sysname-pbr-1-1] description Officeuse

display ip policy-based-route

Use display ip policy-based-route to display PBR policy information.

Syntax

display ip policy-based-route [ policy policy-name ]

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

policy policy-name: Specifies a policy by its name, a case-sensitive string of 1 to 19 characters. If you do not specify a policy, this command displays information for all PBR policies.

Examples

# Display all policy information.

<Sysname> display ip policy-based-route

Policy name: aaa

node 1 permit:

if-match acl 2000

apply next-hop 1.1.1.1

Table 2 Command output

Field	Description
node 1 permit	The match mode of Node 1 is permit.
if-match acl	Compares packets with the ACL.
apply next-hop	Specifies a next hop for permitted packets.

Related commands

policy-based-route

display ip policy-based-route interface

Use display ip policy-based-route interface to display interface PBR configuration and statistics.

Syntax

In standalone mode:

display ip policy-based-route interface interface-type interface-number [ slot slot-number ]

In IRF mode:

display ip policy-based-route interface interface-type interface-number [ chassis chassis-number slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

interface-type interface-number: Specifies an interface by its type and number.

slot slot-number: Specifies a card by its slot number. If you do not specify a card, this command displays information on the active MPU. (In standalone mode.)

chassis chassis-number slot slot-number: Specifies a card on an IRF member device. The chassis-number argument represents the member ID of the IRF member device. The slot-number argument represents the slot number of the card. If you do not specify a card, this command displays information on the global active MPU. (In IRF mode.)

Examples

# Display PBR configuration and statistics on VLAN-interface 2.

<Sysname> display ip policy-based-route interface vlan-interface 2

Policy based routing information for interface Vlan-interface2:

Policy name: aaa

node 0 deny:

Matched: 0

node 1 permit:

if-match acl 3999

Matched: 0

node 2 permit:

if-match acl 2000

apply next-hop 2.2.2.2

Matched: 0

node 5 permit:

if-match acl 3101

apply next-hop 1.1.1.1

apply output-interface Vlan-interface3 track 1

apply output-interface Vlan-interface4 track 2

Matched: 0

Total matched: 0

<Sysname> display ip policy-based-route interface vlan-interface 2

Policy based routing information for interface Vlan-interface2:

Policy name: aaa

node 0 deny:

Matched: 0

node 1 permit:

if-match acl 3999

Matched: 0

node 2 permit:

if-match acl 2000

apply next-hop 2.2.2.2

apply output-interface Vlan-interface3 track 1

apply output-interface Vlan-interface4 track 2

Matched: 0

node 5 permit:

if-match acl 3101

apply next-hop 1.1.1.1

Matched: 0

Total matched: 0

Table 3 Command output

Field	Description
Policy based routing information for interface XXXX(failed)	PBR configuration and statistics on the interface. This field displays failed in brackets if none of the nodes in the policy has been successfully issued to the driver. The failed status will persist even after the policy is successfully issued. To clear the failed status, you must remove the policy from the interface and then apply it on the interface again. NOTE: The failed status is available on a per-slot basis. To obtain this information, you must specify a slot number when you execute the command. · For a global interface (for example, a VLAN interface), which might have member physical interfaces on multiple slots, specify a slot that contains its member interfaces. · For a physical interface, specify its slot number.
node 0 deny(not support) node 2 permit(no resource)	Match mode of the node, permit or deny. If a node fails to be issued to the driver, the command displays the cause in brackets, which include: · not support—The device does not support the match criteria configured on the node. · no resource—No sufficient resources (for example, ACLs) are available for the node. NOTE: The cause is available only on a per-slot basis. To obtain this information, you must specify a slot number when you execute the command. · For a global interface (for example, a VLAN interface), which might have member physical interfaces on multiple slots, specify a slot that contains its member interfaces. · For a physical interface, specify its slot number.
if-match acl	Compares packets with the ACL.
apply next-hop	Specifies a next hop for permitted packets.
Matched: 0 (no statistics resource)	Number of successful matches on the node. If the device does not have sufficient resources to count matches, this field displays no statistics resource in brackets. NOTE: The statistics collection failure cause is available only on a per-slot basis. To obtain this information, you must specify a slot number when you execute the command. · For a global interface (for example, a VLAN interface), which might have member physical interfaces on multiple slots, specify a slot that contains its member interfaces. · For a physical interface, specify its slot number.
Total matched	Total number of successful matches on all nodes.

Related commands

reset ip policy-based-route statistics

display ip policy-based-route local

Use display ip policy-based-route local to display local PBR configuration and statistics.

Syntax

In standalone mode:

display ip policy-based-route local [ slot slot-number ]

In IRF mode:

display ip policy-based-route local [ chassis chassis-number slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

slot slot-number: Specifies a card by its slot number. If you do not specify a card, this command displays local PBR configuration and statistics for the active MPU. (In standalone mode.)

chassis chassis-number slot slot-number: Specifies a card on an IRF member device. The chassis-number argument represents the member ID of the IRF member device. The slot-number argument represents the slot number of the card. If you do not specify a card, this command displays local PBR configuration and statistics for the global active MPU. (In IRF mode.)

Examples

# Display local PBR configuration and statistics.

<Sysname> display ip policy-based-route local

Policy based routing information for local:

Policy name: aaa

node 0 deny:

Matched: 0

node 1 permit:

if-match acl 3999

Matched: 0

node 2 permit:

if-match acl 2000

apply next-hop 2.2.2.2

Matched: 0

node 5 permit:

if-match acl 3101

apply next-hop 1.1.1.1

Matched: 0

Total matched: 0

Table 4 Command output

Field	Description
Policy based routing information for local	Local PBR configuration and statistics.
node 0 deny/node 2 permit	Match mode of the node: permit or deny.
if-match acl	Compares packets with the ACL.
apply next-hop	Specifies a next hop for permitted packets.
Matched: 0	Number of successful matches on the node.
Total matched	Total number of successful matches on all nodes.

Related commands

reset ip policy-based-route statistics

display ip policy-based-route setup

Use display ip policy-based-route setup to display PBR configuration.

Syntax

display ip policy-based-route setup

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Examples

# Display PBR configuration.

<Sysname> display ip policy-based-route setup

Policy name Type Interface

pr01 Forward Vlan-interface2

aaa Egress Tunnel1

aaa Local N/A

Table 5 Command output

Field	Description
Type	Type of the PBR: · Forward—Interface PBR. · Egress—Outbound PBR. · Local—Local PBR.
Interface	Interface where the policy is applied.

Field

Description

Type

Type of the PBR:

· Forward—Interface PBR.

· Egress—Outbound PBR.

· Local—Local PBR.

Interface

Interface where the policy is applied.

Related commands

ip policy-based-route

if-match acl

Use if-match acl to set an ACL match criterion.

Use undo if-match acl to restore the default.

Syntax

if-match acl { acl-number | name acl-name }

undo if-match acl

Default

No ACL match criterion is set.

Views

Policy node view

Predefined user roles

network-admin

mdc-admin

Parameters

acl-number: Specifies an ACL by its number in the range of 2000 to 2999 for a basic ACL, and in the range of 3000 to 3999 for an advanced ACL.

name acl-name: Specifies an ACL by its name, a case-insensitive string of 1 to 63 characters starting with letter a to z or A to Z. The ACL name cannot be all. For the command to take effect, make sure the specified ACL is a basic or advanced ACL.

Examples

# Configure Node 11 of policy aa to permit the packets matching ACL 2011.

<Sysname> system-view

[Sysname] policy-based-route aa permit node 11

[Sysname-pbr-aa-11] if-match acl 2011

# Configure Node 11 of policy aa to permit the packets matching ACL aaa.

<Sysname> system-view

[Sysname] policy-based-route aa permit node 11

[Sysname-pbr-aa-11] if-match acl name aaa

if-match service-chain

Use if-match service-chain to set a service chain match criterion.

Use undo if-match service-chain to restore the default.

Syntax

if-match service-chain { path-id service-path-id [ path-index service-patch-index ] }

undo if-match service-chain [ path-id service-path-id ] ]

Default

No service chain match criteria are set.

Views

Policy node view

Predefined user roles

network-admin

mdc-admin

Parameters

path-id service-path-id: Specifies a service chain by its path ID in the range of 1 to 16777215. The path ID uniquely identifies a service chain.

path-index service-path-index: Specifies a node in a service chain by its index in the range of 1 to 255. This option is used to distinguish packets sent from different nodes in a service chain. If all packets are sent from one node, you do not need to specify this option.

Examples

# Set a service chain match criterion to match packets with service chain path ID 1 and node index 10.

<Sysname> system-view

[Sysname] policy-based-route aa permit node 5

[Sysname-pbr-aa-5] if-match service-chain path-id 1 path-index 10

ip local policy-based-route

Use ip local policy-based-route to specify a policy for local PBR.

Use undo ip local policy-based-route to restore the default.

Syntax

ip local policy-based-route policy-name

undo ip local policy-based-route

Default

No policy is referenced for local PBR.

Views

System view

Predefined user roles

network-admin

mdc-admin

Parameters

policy-name: Specifies a policy by its name, a case-sensitive string of 1 to 19 characters. The specified policy must already exist.

Usage guidelines

Local PBR guides the forwarding of locally generated packets, such as ICMP packets generated by using the ping command.

Local PBR might affect local services, such as ping and Telnet. When you use local PBR, make sure you fully understand its impact on local services of the device.

You can specify only one policy for local PBR and must make sure the specified policy already exists.

Before you apply a new policy, you must first remove the current policy.

Examples

# Configure local PBR based on policy aaa.

<Sysname> system-view

[Sysname] ip local policy-based-route aaa

Related commands

display ip policy-based-route setup

ip policy-based-route apply

policy-based-route

ip policy-based-route

Use ip policy-based-route to specify a policy for interface PBR on an interface.

Use undo ip policy-based-route to restore the default.

Syntax

ip policy-based-route policy-name

undo ip policy-based-route

Default

No policy is applied to an interface.

Views

Interface view

Predefined user roles

network-admin

mdc-admin

Parameters

policy-name: Specifies a policy by its name, a case-sensitive string of 1 to 19 characters. The specified policy must already exist.

Usage guidelines

Interface PBR is not supported on Layer 3 aggregate interfaces, Layer 3 aggregate subinterfaces, or member ports of the Layer 3 aggregate subinterfaces.

Examples

# Apply policy aaa to VLAN-interface 2.

<Sysname> system-view

[Sysname] interface vlan-interface 2

[Sysname-Vlan-interface2] ip policy-based-route aaa

Related commands

display ip policy-based-route setup

policy-based-route

Use policy-based-route to create a policy node and enter its view, or enter the view of an existing policy node.

Use undo policy-based-route to delete a policy or policy node.

Syntax

policy-based-route policy-name [ deny | permit ] node node-number

undo policy-based-route policy-name [ deny | node node-number | permit ]

Default

No policy nodes exist.

Views

System view

Predefined user roles

network-admin

mdc-admin

Parameters

policy-name: Specifies a policy by its name, a case-sensitive string of 1 to 19 characters.

deny: Specifies the match mode for the policy node as deny.

permit: Specifies the match mode for the policy node as permit (default mode).

node node-number: Specifies a policy node by its number. A smaller number has a higher priority. The value range for the node-number argument is 0 to 255.

Usage guidelines

A policy that has been applied to an interface or locally cannot be deleted. To delete it, you must first cancel the application.

· If a policy node is specified, the undo policy-based-route command deletes the specified policy node.

· If a match mode is specified, the command deletes all nodes configured with the match mode.

· If no policy node or match mode is specified, the command deletes the whole policy.

Examples

# Create permit-mode of Node 10 for policy policy1 and enter its view.

<Sysname> system-view

[Sysname] policy-based-route policy1 permit node 10

[Sysname-pbr-policy1-10]

Related commands

display ip policy-based-route

reset ip policy-based-route statistics

Use reset ip policy-based-route statistics to clear PBR statistics.

Syntax

reset ip policy-based-route statistics [ policy policy-name ]

Views

User view

Predefined user roles

network-admin

mdc-admin

Parameters

policy policy-name: Specifies a policy by its name, a case-sensitive string of 1 to 19 characters. If you do not specify a policy, this command clears PBR statistics for all policies.

Examples

# Clear all PBR statistics.

<Sysname> reset ip policy-based-route statistics

Related commands

display ip policy-based-route interface

display ip policy-based-route local

06 Layer 3 - IP Routing Command Reference

display ip policy-based-route

display ip policy-based-route interface

ip policy-based-route

Intelligent Terminal Products

Product Support Services

Technical Service Solutions

Resource Center

Policy

Online Help

Become a Partner

Partner Policy & Program

Global Learning

Partner Sales Resources

Service Business

News & Events

Contact Us