verbose: Displays detailed routing table information, including information about both active and inactive routes. If you do not specify this keyword, the command displays only brief information about active routes.

standby slot slot-number: Displays backup routing table information for an IRF member device. If you do not specify this option, the command displays routing table information.

Examples

# Display brief information about active routes in the routing table.

<Sysname> display ip routing-table

Destinations : 13 Routes : 13

Destination/Mask Proto Pre Cost NextHop Interface

0.0.0.0/32 Direct 0 0 127.0.0.1 InLoop0

1.1.1.0/24 Static 60 0 192.168.47.4 Vlan1

127.0.0.0/8 Direct 0 0 127.0.0.1 InLoop0

127.0.0.0/32 Direct 0 0 127.0.0.1 InLoop0

127.0.0.1/32 Direct 0 0 127.0.0.1 InLoop0

127.255.255.255/32 Direct 0 0 127.0.0.1 InLoop0

192.168.1.0/24 Direct 0 0 192.168.1.40 Vlan11

192.168.1.0/32 Direct 0 0 192.168.1.40 Vlan11

192.168.1.40/32 Direct 0 0 127.0.0.1 InLoop0

192.168.1.255/32 Direct 0 0 192.168.1.40 Vlan11

224.0.0.0/4 Direct 0 0 0.0.0.0 NULL0

224.0.0.0/24 Direct 0 0 0.0.0.0 NULL0

255.255.255.255/32 Direct 0 0 127.0.0.1 InLoop0

Table 1 Command output

Field	Description
Destinations	Number of destination addresses.
Routes	Number of routes.
Destination/Mask	Destination address/mask length.
Proto	Protocol that installed the route.
Pre	Preference of the route.
Cost	Cost of the route.
NextHop	Next hop address of the route.
Interface	Output interface for packets to be forwarded along the route.
Summary Count	Number of routes.

# Display detailed information about all routes in the routing table.

<Sysname> display ip routing-table verbose

Destinations : 13 Routes : 13

Destination: 0.0.0.0/32

Protocol: Direct Process ID: 0

SubProtID: 0x0 Age: 08h34m37s

Cost: 0 Preference: 0

Tag: 0 State: Active NoAdv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0x2 OrigAs: 0

NibID: 0x10000000 LastAs: 0

AttrID: 0xffffffff Neighbor: 0.0.0.0

Flags: 0x1000c OrigNextHop: 127.0.0.1

Label: NULL RealNextHop: 127.0.0.1

BkLabel: NULL BkNextHop: N/A

Tunnel ID: Invalid Interface: InLoopBack0

BkTunnel ID: Invalid BkInterface: N/A

Destination: 1.1.1.0/24

Protocol: Static Process ID: 0

SubProtID: 0x0 Age: 04h20m37s

Cost: 0 Preference: 60

Tag: 0 State: Active Adv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0x2 OrigAs: 0

NibID: 0x10000003 LastAs: 0

AttrID: 0xffffffff Neighbor: 0.0.0.0

Flags: 0x1008c OrigNextHop: 192.168.47.4

Label: NULL RealNextHop: 192.168.47.4

BkLabel: NULL BkNextHop: N/A

Tunnel ID: Invalid Interface: Vlan-interface1

BkTunnel ID: Invalid BkInterface: N/A

...

Table 2 Command output

Field	Description
Destinations	Number of destination addresses.
Routes	Number of routes.
Destination	Destination address/mask length.
Protocol	Protocol that installed the route.
SubProtID	ID of the subprotocol for routing.
Age	Time for which the route has been in the routing table.
Cost	Cost of the route.
Preference	Preference of the route.
Tag	Route tag.
State	Route status: · Active—Active unicast route. · Adv—Route that can be advertised. · Inactive—Inactive route. · NoAdv—Route that the router must not advertise. · Vrrp—Routes generated by VRRP. · Nat—Routes generated by NAT.
OrigTblID	Original routing table ID.
TableID	ID of the routing table.
OrigAs	Original AS number.
NibID	ID of the next hop.
LastAs	Last AS number.
AttrID	Attribute ID.
Neighbor	Address of the neighbor determined by the routing protocol.
Flags	Flags of the route.
OrigNextHop	Next hop address of the route.
RealNextHop	Real next hop of the route.
BkNexthop	Backup next hop.
Interface	Output interface for packets to be forwarded along the route.
BkInterface	Backup output interface.
FtnIndex	Index of the FTN entry.
Summary Count	Number of routes.

display ip routing-table acl

Use display ip routing-table acl to display information about routes permitted by a specific basic ACL.

Syntax

display ip routing-table acl acl-number [ verbose ] [ standby slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

acl-number: Specifies a basic ACL by its number in the range of 2000 to 2999.

verbose: Displays detailed information about all routes permitted by the basic ACL. If you do not specify this keyword, the command displays only brief information about active routes permitted by the basic ACL.

standby slot slot-number: Displays backup information about routes permitted by the basic ACL for an IRF member device. If you do not specify this option, the command displays information about routes permitted by the basic ACL.

Usage guidelines

If the specified ACL does not exist or has no rules configured, the command displays information about all routes.

Examples

# Define basic ACL 2000 and set the route filtering rules.

<Sysname> system-view

[Sysname] acl number 2000

[Sysname-acl-basic-2000] rule permit source 192.168.1.0 0.0.0.255

[Sysname-acl-basic-2000] rule deny source any

# Display brief information about active routes permitted by basic ACL 2000.

[Sysname-acl-basic-2000] display ip routing-table acl 2000

Routes Matched by Access control list : 2000

Summary Count : 4

Destination/Mask Proto Pre Cost NextHop Interface

192.168.1.0/24 Direct 0 0 192.168.1.111 Vlan1

192.168.1.0/32 Direct 0 0 192.168.1.111 Vlan1

192.168.1.111/32 Direct 0 0 127.0.0.1 InLoop0

192.168.1.255/32 Direct 0 0 192.168.1.111 Vlan1

For command output, see Table 1.

# Display detailed information about all routes permitted by basic ACL 2000.

<Sysname> display ip routing-table acl 2000 verbose

Routes Matched by Access control list : 2000

Summary Count : 4

Destination: 192.168.1.0/24

Protocol: Direct Process ID: 0

SubProtID: 0x1 Age: 04h20m37s

Cost: 0 Preference: 0

Tag: 0 State: Active Adv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0x2 OrigAs: 0

NibID: 0x10000003 LastAs: 0

AttrID: 0xffffffff Neighbor: 0.0.0.0

Flags: 0x10080 OrigNextHop: 192.168.1.111

Label: NULL RealNextHop: 192.168.1.111

BkLabel: NULL BkNextHop: N/A

Tunnel ID: Invalid Interface: Vlan-interface1

BkTunnel ID: Invalid BkInterface: N/A

Destination: 192.168.1.0/32

Protocol: Direct Process ID: 0

SubProtID: 0x0 Age: 04h20m37s

Cost: 0 Preference: 0

Tag: 0 State: Active NoAdv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0x2 OrigAs: 0

NibID: 0x10000003 LastAs: 0

AttrID: 0xffffffff Neighbor: 0.0.0.0

Flags: 0x1008c OrigNextHop: 192.168.1.111

Label: NULL RealNextHop: 192.168.1.111

BkLabel: NULL BkNextHop: N/A

Tunnel ID: Invalid Interface: Vlan-interface1

BkTunnel ID: Invalid BkInterface: N/A

Destination: 192.168.1.111/32

Protocol: Direct Process ID: 0

SubProtID: 0x1 Age: 04h20m37s

Cost: 0 Preference: 0

Tag: 0 State: Active NoAdv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0x2 OrigAs: 0

NibID: 0x10000000 LastAs: 0

AttrID: 0xffffffff Neighbor: 0.0.0.0

Flags: 0x10004 OrigNextHop: 127.0.0.1

Label: NULL RealNextHop: 127.0.0.1

BkLabel: NULL BkNextHop: N/A

Tunnel ID: Invalid Interface: InLoopBack0

BkTunnel ID: Invalid BkInterface: N/A

Destination: 192.168.1.255/32

Protocol: Direct Process ID: 0

SubProtID: 0x0 Age: 04h20m37s

Cost: 0 Preference: 0

Tag: 0 State: Active NoAdv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0x2 OrigAs: 0

NibID: 0x10000003 LastAs: 0

AttrID: 0xffffffff Neighbor: 0.0.0.0

Flags: 0x1008c OrigNextHop: 192.168.1.111

Label: NULL RealNextHop: 192.168.1.111

BkLabel: NULL BkNextHop: N/A

Tunnel ID: Invalid Interface: Vlan-interface1

BkTunnel ID: Invalid BkInterface: N/A

For command output, see Table 2.

display ip routing-table ip-address

Use display ip routing-table ip-address to display information about routes to a specific destination address.

Use display ip routing-table ip-address1 to ip-address2 to display information about routes to a range of destination addresses.

Syntax

display ip routing-table ip-address [ mask | mask-length ] [ longer-match ] [ verbose ] [ standby slot slot-number ]

display ip routing-table ip-address1 to ip-address2 [ verbose ] [ standby slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

ip-address: Specifies a destination IP address in dotted decimal notation.

mask: Specifies the IP address mask in dotted decimal notation.

mask-length: Specifies the mask length, an integer in the range of 0 to 32.

longer-match: Displays the route entry with the longest mask.

ip-address1 to ip-address2: Specifies a destination IP address range.

verbose: Displays detailed routing table information, including information about both active and inactive routes. If you do not specify this keyword, the command displays brief information about active routes.

standby slot slot-number: Displays backup information about routes to the specified destination addresses for an IRF member device. If you do not specify this option, the command displays information about routes to the specified destination addresses.

Usage guidelines

Executing the command with different parameters yields different outputs.

· display ip routing-table ip-address

¡ The system ANDs the entered destination IP address with the subnet mask in each active route entry.

¡ The system ANDs the destination IP address in each active route entry with its own subnet mask.

If the two operations yield the same result for an entry, the entry is displayed.

· display ip routing-table ip-address mask

¡ The system ANDs the entered destination IP address with the entered subnet mask.

¡ The system ANDs the destination IP address in each active route entry with the entered subnet mask.

If the two operations yield the same result for an entry and the entry has a subnet mask less than or equal to the entered subnet mask, the entry is displayed.

· display ip routing-table ip-address longer-match

¡ The system ANDs the entered destination IP address with the subnet mask in each active route entry.

¡ The system ANDs the destination IP address in each active route entry with its own subnet mask.

If the two operations yield the same result for multiple entries, the one with longest mask length is displayed.

· display ip routing-table ip-address mask longer-match

¡ The system ANDs the entered destination IP address with the entered subnet mask.

¡ The system ANDs the destination IP address in each active route entry with the entered subnet mask.

If the two operations yield the same result for multiple entries and the entries have a mask less than or equal to the entered subnet mask, the one with the longest mask length is displayed.

· display ip routing-table ip-address1 to ip-address2

The system displays active route entries with destinations in the range of ip-address1/32 to ip-address2/32.

Examples

# Display brief information about the routes to the destination IP address 11.0.0.1.

<Sysname> display ip routing-table 11.0.0.1

Summary Count : 3

Destination/Mask Proto Pre Cost NextHop Interface

11.0.0.0/8 Static 60 0 0.0.0.0 NULL0

11.0.0.0/16 Static 60 0 0.0.0.0 NULL0

11.0.0.0/24 Static 60 0 0.0.0.0 NULL0

# Display brief information about the routes to the destination IP address 11.0.0.1 and mask length 20.

<Sysname> display ip routing-table 11.0.0.1 20

Summary Count : 2

Destination/Mask Proto Pre Cost NextHop Interface

11.0.0.0/8 Static 60 0 0.0.0.0 NULL0

11.0.0.0/16 Static 60 0 0.0.0.0 NULL0

# Display brief information about the most specific route to the destination address 11.0.0.1.

<Sysname> display ip routing-table 11.0.0.1 longer-match

Summary Count : 1

Destination/Mask Proto Pre Cost NextHop Interface

11.0.0.0/24 Static 60 0 0.0.0.0 NULL0

# Display brief information about the most specific route to the destination IP address 11.0.0.1 and mask length 20.

<Sysname> display ip routing-table 11.0.0.1 20 longer-match

Summary Count : 1

Destination/Mask Proto Pre Cost NextHop Interface

11.0.0.0/16 Static 60 0 0.0.0.0 NULL0

# Display brief information about the routes to destination addresses in the range of 1.1.1.0 to 5.5.5.0.

<Sysname> display ip routing-table 1.1.1.0 to 5.5.5.0

Summary Count : 6

Destination/Mask Proto Pre Cost NextHop Interface

1.1.1.1/32 Direct 0 0 127.0.0.1 InLoop0

2.2.2.0/24 Direct 0 0 2.2.2.1 Vlan2

3.3.3.0/24 Direct 0 0 3.3.3.1 Vlan2

3.3.3.1/32 Direct 0 0 127.0.0.1 InLoop0

4.4.4.0/24 Direct 0 0 4.4.4.1 Vlan1

4.4.4.1/32 Direct 0 0 127.0.0.1 InLoop0

For command output, see Table 1.

display ip routing-table prefix-list

Use display ip routing-table prefix-list to display routes permitted by an IP prefix list.

Syntax

display ip routing-table prefix-list prefix-list-name [ verbose ] [ standby slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

prefix-list-name: Specifies an IP prefix list by its name, a case-sensitive string of 1 to 63 characters.

verbose: Displays detailed information about all routes permitted by the IP prefix list. If you do not specify this keyword, the command displays brief information about active routes permitted by the IP prefix list.

standby slot slot-number: Displays backup routes permitted by the IP prefix list for an IRF member device. If you do not specify this option, the command displays routes permitted by the IP prefix list.

Usage guidelines

If the specified IP prefix list does not exist, the command displays information about all routes.

Examples

# Create an IP prefix list named test to permit the route 1.1.1.0/24.

<Sysname> system-view

[Sysname] ip prefix-list test permit 1.1.1.0 24

# Display brief information about the active route permitted by the IP prefix list.

[Sysname] display ip routing-table prefix-list test

Routes Matched by Prefix list : test

Summary Count : 1

Destination/Mask Proto Pre Cost NextHop Interface

1.1.1.0/24 Direct 0 0 1.1.1.2 Vlan2

For command output, see Table 1.

# Display detailed information about all routes permitted by the IP prefix list.

[Sysname] display ip routing-table prefix-list test verbose

Routes Matched by Prefix list : test

Summary Count : 1

Destination: 1.1.1.0/24

Protocol: Direct Process ID: 0

SubProtID: 0x1 Age: 04h20m37s

Cost: 0 Preference: 0

Tag: 0 State: Active Adv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0x2 OrigAs: 0

NibID: 0x10000003 LastAs: 0

AttrID: 0xffffffff Neighbor: 0.0.0.0

Flags: 0x1008c OrigNextHop: 1.1.1.2

Label: NULL RealNextHop: 1.1.1.2

BkLabel: NULL BkNextHop: N/A

Tunnel ID: Invalid Interface: Vlan-interface2

BkTunnel ID: Invalid BkInterface: N/A

For command output, see Table 2.

display ip routing-table protocol

Use display ip routing-table protocol to display information about routes installed by a protocol.

Syntax

display ip routing-table protocol protocol [ inactive | verbose ] [ standby slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

protocol: Specifies a routing protocol. It can be bgp, direct, isis, ospf, rip, or static.

inactive: Displays information about inactive routes. If you do not specify this keyword, the command displays information about both active and inactive routes.

verbose: Displays detailed routing table information. If you do not specify this keyword, the command displays brief routing information.

standby slot slot-number: Displays backup information about routes installed by the protocol for an IRF member device. If you do not specify this option, the command displays information about routes installed by the protocol.

Examples

# Display brief information about direct routes.

<Sysname> display ip routing-table protocol direct

Summary Count : 13

Direct Routing Table Status : <Active>

Summary Count : 13

Destination/Mask Proto Pre Cost NextHop Interface

0.0.0.0/32 Direct 0 0 127.0.0.1 InLoop0

2.2.2.0/24 Direct 0 0 2.2.2.1 Vlan2

2.2.2.0/32 Direct 0 0 2.2.2.1 Vlan2

2.2.2.2/32 Direct 0 0 127.0.0.1 InLoop0

2.2.2.255/32 Direct 0 0 2.2.2.1 Vlan2

127.0.0.0/8 Direct 0 0 127.0.0.1 InLoop0

127.0.0.0/32 Direct 0 0 127.0.0.1 InLoop0

127.0.0.1/32 Direct 0 0 127.0.0.1 InLoop0

127.255.255.255/32 Direct 0 0 127.0.0.1 InLoop0

192.168.80.0/24 Direct 0 0 192.168.80.10 Vlan1

192.168.80.0/32 Direct 0 0 192.168.80.10 Vlan1

192.168.80.10/32 Direct 0 0 127.0.0.1 InLoop0

192.168.80.255/32 Direct 0 0 192.168.80.10 Vlan1

Direct Routing Table Status : <Inactive>

Summary Count : 0

# Display brief information about static routes.

<Sysname> display ip routing-table protocol static

Summary Count : 2

Static Routing Table Status : <Active>

Summary Count : 0

Static Routing Table Status : <Inactive>

Summary Count : 2

Destination/Mask Proto Pre Cost NextHop Interface

1.2.3.0/24 Static 60 0 1.2.4.5 Vlan10

3.0.0.0/8 Static 60 0 2.2.2.2 Vlan1

For command output, see Table 1.

display ip routing-table statistics

Use display ip routing-table statistics to display IPv4 route statistics.

Syntax

display ip routing-table statistics [ standby slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

standby slot slot-number: Displays backup IPv4 route statistics for an IRF member device. If you do not specify this option, the command displays IPv4 route statistics.

Examples

# Display IPv4 route statistics for the public network.

<Sysname> display ip routing-table statistics

Total prefixes: 15 Active prefixes: 15

Proto route active added deleted

DIRECT 12 12 30 18

STATIC 3 3 5 2

RIP 0 0 0 0

OSPF 0 0 0 0

ISIS 0 0 0 0

BGP 0 0 0 0

Total 15 15 35 20

Table 3 Command output

Field	Description
Total prefixes	Total number of prefixes.
Active prefixes	Number of active prefixes.
Proto	Protocol that installed the route.
route	Number of routes installed by the protocol.
active	Number of active routes.
added	Number of routes added to the routing table after the router started up or the routing table was cleared most recently.
deleted	Number of routes marked as deleted, which will be cleared after a period.
Total	Total number of routes.

display ipv6 rib attribute

Use display ipv6 rib attribute to display route attribute information in the IPv6 RIB.

Syntax

display ipv6 rib attribute [ attribute-id ] [ standby slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

attribute-id: Specifies a route attribute by its ID in the range of 0 to FFFFFFFF.

standby slot slot-number: Displays backup route attribute information in the IPv6 RIB for an IRF member device. If you do not specify this option, the command displays route attribute information in the IPv6 RIB.

Examples

# Display route attribute information in the IPv6 RIB.

<Sysname> display ipv6 rib attribute

Total number of attribute(s): 1

Detailed information of attribute 0x9:

Flag: 0x0

Protocol: BGP4+

Address family: IPv6

Reference count: 0

Local preference: 0

Ext-communities number: 0

Ext-communities value: N/A

Communities number: 0

Communities value: N/A

AS-path number: 0

AS-path value: N/A

For command output, see Table 10.

display ipv6 rib graceful-restart

Use display ipv6 rib graceful-restart to display IPv6 RIB GR state information.

Syntax

display ipv6 rib graceful-restart

Views

Any view

Predefined user roles

network-admin

network-operator

Examples

# Display IPv6 RIB GR state information.

<Sysname> display ipv6 rib graceful-restart

RIB GR state : Phase2-calculation end

RCOM GR State : Flush end

Protocol GR state:

No. Protocol Lifetime FD State Start/End

--------------------------------------------------

1 DIRECT6 480 29 End No/No

2 STATIC6 480 32 End No/No

3 ISISV6 480 30 End No/No

4 BGP4+ 480 31 End No/No

For command output, see Table 11.

display ipv6 rib nib

Use display ipv6 rib nib to display next hop information in the IPv6 RIB.

Syntax

display ipv6 rib nib [ self-originated ] [ nib-id ] [ verbose ] [ standby slot slot-number ]

display ipv6 rib nib protocol protocol-name [ verbose ] [ standby slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

self-originated: Displays information about next hops of self-originated routes in the IPv6 RIB.

nib-id: Specifies a NIB by its ID in the range of 1 to FFFFFFFF.

verbose: Displays detailed next hop information in the IPv6 RIB. If you do not specify this keyword, the command displays brief next hop information in the IPv6 RIB.

protocol protocol-name: Specifies a protocol by its name, which can be bgp+, direct6, isisv6, ospfv3, ripng, or static6.

standby slot slot-number: Displays backup next hop information in the IPv6 RIB for an IRF member device. If you do not specify this option, the command displays next hop information in the IPv6 RIB.

Examples

# Display brief next hop information in the IPv6 RIB.

<Sysname> display ipv6 rib nib

Total number of nexthop(s): 151

NibID: 0x20000000 Sequence: 0

Type: 0x1 Flushed: Yes

UserKey0: 0x0 VrfNthp: 1

UserKey1: 0x0 Nexthop: ::

IFIndex: 0x111 LocalAddr: ::

NibID: 0x20000001 Sequence: 1

Type: 0x1 Flushed: Yes

UserKey0: 0x0 VrfNthp: 1

UserKey1: 0x0 Nexthop: ::1

IFIndex: 0x112 LocalAddr: ::1

...

# Display detailed next hop information in the IPv6 RIB.

<Sysname> display ipv6 rib nib verbose

Total number of nexthop(s): 151

NibID: 0x20000000 Sequence: 0

Type: 0x1 Flushed: Yes

UserKey0: 0x0 VrfNthp: 1

UserKey1: 0x0 Nexthop: ::

IFIndex: 0x111 LocalAddr: ::

RefCnt: 4 FlushRefCnt: 1

Flag: 0x84 Version: 1

1 nexthop(s):

PrefixIndex: 0 OrigNexthop: ::

RelyDepth: 0 RealNexthop: ::

Interface: NULL0 LocalAddr: ::

TunnelCnt: 0 Vrf: vpn1

TunnelID: N/A

NibID: 0x20000001 Sequence: 1

Type: 0x1 Flushed: Yes

UserKey0: 0x0 VrfNthp: 1

UserKey1: 0x0 Nexthop: ::1

IFIndex: 0x112 LocalAddr: ::1

RefCnt: 4 FlushRefCnt: 1

Flag: 0x84 Version: 1

1 nexthop(s):

PrefixIndex: 0 OrigNexthop: ::1

RelyDepth: 0 RealNexthop: ::1

Interface: InLoop0 LocalAddr: ::1

TunnelCnt: 0 Vrf: vpn1

TunnelID: N/A

...

For command output, see Table 12 and Table 13.

display ipv6 route-direct nib

Use display ipv6 route-direct nib to display next hop information for IPv6 direct routes.

Syntax

display ipv6 route-direct nib [ nib-id ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

nib-id: Specifies a NIB by its ID in the range of 1 to FFFFFFFF.

verbose: Displays detailed next hop information for IPv6 direct routes. If you do not specify this keyword, the command displays brief next hop information for IPv6 direct routes.

Examples

# Display brief next hop information for IPv6 direct routes.

<Sysname> display ipv6 route-direct nib

Total number of nexthop(s): 115

NibID: 0x20000000 Sequence: 0

Type: 0x1 Flushed: Yes

UserKey0: 0x0 VrfNthp: 1

UserKey1: 0x0 Nexthop: ::

IFIndex: 0x111 LocalAddr: ::

NibID: 0x20000001 Sequence: 1

Type: 0x1 Flushed: Yes

UserKey0: 0x0 VrfNthp: 1

UserKey1: 0x0 Nexthop: ::1

IFIndex: 0x112 LocalAddr: ::1

...

Table 4 Command output

Field	Description
NibID	ID of the NIB.
Sequence	Sequence number of the NIB.
Type	Type of the NIB.
Flushed	Indicates whether the route with the NIB has been flushed to the FIB.
UserKey0	Reserved data 1.
UserKey1	Reserved data 2.
Nexthop	Next hop address.
IFIndex	Interface index.
LocalAddr	Local interface address.

# Display detailed next hop information for IPv6 direct routes.

<Sysname> display ipv6 route-direct nib verbose

Total number of nexthop(s): 115

NibID: 0x20000000 Sequence: 0

Type: 0x1 Flushed: Yes

UserKey0: 0x0 VrfNthp: 1

UserKey1: 0x0 Nexthop: ::

IFIndex: 0x111 LocalAddr: ::

RefCnt: 1 FlushRefCnt: 0

Flag: 0x2 Version: 1

1 nexthop(s):

PrefixIndex: 0 OrigNexthop: ::

RelyDepth: 0 RealNexthop: ::

Interface: NULL0 LocalAddr: ::

TunnelCnt: 0 Vrf: vpn1

TunnelID: N/A

NibID: 0x20000001 Sequence: 1

Type: 0x1 Flushed: Yes

UserKey0: 0x0 VrfNthp: 1

UserKey1: 0x0 Nexthop: ::1

IFIndex: 0x112 LocalAddr: ::1

RefCnt: 1 FlushRefCnt: 0

Flag: 0x2 Version: 1

1 nexthop(s):

PrefixIndex: 0 OrigNexthop: ::1

RelyDepth: 0 RealNexthop: ::1

Interface: InLoop0 LocalAddr: ::1

TunnelCnt: 0 Vrf: vpn1

TunnelID: N/A

...

Table 5 Command output

Field	Description
x nexthop(s)	Number of next hops.
PrefixIndex	Prefix index of the next hop for an ECMP route.
OrigNexthop	Original next hop.
RealNexthop	Real next hop.
Interface	Output interface.
localAddr	Local interface address.
RelyDepth	Recursion depth.
RefCnt	Reference count of the next hop.
FlushRefCnt	Reference count of the next hop that is flushed to the FIB.
Flag	Flag of the next hop.
Version	Version of the next hop.

display ipv6 routing-table

Use display ipv6 routing-table to display IPv6 routing table information.

Syntax

display ipv6 routing-table [ verbose ] [ standby slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

standby slot slot-number: Displays backup IPv6 routing table information for an IRF member device. If you do not specify this option, the command displays IPv6 routing table information.

Examples

# Display brief information about active routes in the IPv6 routing table.

<Sysname> display ipv6 routing-table

Destinations : 3 Routes : 3

Destination: ::1/128 Protocol : Direct

NextHop : ::1 Preference: 0

Interface : InLoop0 Cost : 0

Destination: FE80::/10 Protocol : Direct

NextHop : :: Preference: 0

Interface : NULL0 Cost : 0

Destination: FF00::/8 Protocol : Direct

NextHop : :: Preference: 0

Interface : NULL0 Cost : 0

Table 6 Command output

Field	Description
Destinations	Number of destination addresses.
Routes	Number of routes.
Destination	IPv6 address and prefix of the destination network or host.
NextHop	Next hop address of the route.
Preference	Preference of the route.
Interface	Output interface for packets to be forwarded along the route.
Protocol	Protocol that installed the route. Route types include: · O_INTRA—OSPF intra area route. · O_INTER—OSPF inter area route. · O_ASE1—OSPF external type 1 route. · O_ASE2—OSPF external type 2 route. · O_NSSA1—OSPF NSSA external type 1 route. · O_NSSA2—OSPF NSSA external type 2 route. · O_SUM—OSPF summary route. · IS_L1—IS-IS level-1 route. · IS_L2—IS-IS level-2 route. · IS_SUM—IS-IS summary route.
Cost	Cost of the route.
Summary Count	Number of routes.

# Display detailed information about all routes in the routing table.

<Sysname> display ipv6 routing-table verbose

Destinations : 3 Routes : 3

Destination: ::1/128

Protocol: Direct Process ID: 0

SubProtID: 0x0 Age: 00h53m50s

Cost: 0 Preference: 0

Tag: 0 State: Active NoAdv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0xa OrigAs: 0

NibID: 0x20000000 LastAs: 0

AttrID: 0xffffffff Neighbor: ::

Flags: 0x10004 OrigNextHop: ::1

Label: NULL RealNextHop: ::1

BkLabel: NULL BkNextHop: N/A

Tunnel ID: Invalid Interface: InLoopBack0

BkTunnel ID: Invalid BkInterface: N/A

Destination: FE80::/10

Protocol: Direct Process ID: 0

SubProtID: 0x0 Age: 00h53m50s

Cost: 0 Preference: 0

Tag: 0 State: Active NoAdv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0xa OrigAs: 0

NibID: 0x20000002 LastAs: 0

AttrID: 0xffffffff Neighbor: ::

Flags: 0x10084 OrigNextHop: ::

Label: NULL RealNextHop: ::

BkLabel: NULL BkNextHop: N/A

Tunnel ID: Invalid Interface: NULL0

BkTunnel ID: Invalid BkInterface: N/A

Destination: FF00::/8

Protocol: Direct Process ID: 0

SubProtID: 0x0 Age: 00h53m50s

Cost: 0 Preference: 0

Tag: 0 State: Active NoAdv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0xa OrigAs: 0

NibID: 0x20000001 LastAs: 0

AttrID: 0xffffffff Neighbor: ::

Flags: 0x10014 OrigNextHop: ::

Label: NULL RealNextHop: ::

BkLabel: NULL BkNextHop: N/A

Tunnel ID: Invalid Interface: NULL0

BkTunnel ID: Invalid BkInterface: N/A

Table 7 Command output

Field	Description
Destination	IPv6 address and prefix of the destination network or host.
Protocol	Protocol that installed the route.
SubProtID	ID of the subprotocol for routing.
Age	Time for which the route has been in the routing table.
Cost	Cost of the route.
Preference	Preference of the route.
IpPre	IP precedence.
QosLocalID	Local QoS ID.
Tag	Tag of the route.
State	Route status: · Active—Active unicast route. · Adv—Route that can be advertised. · Inactive—Inactive route. · NoAdv—Route that the router must not advertise. · Vrrp—Routes generated by VRRP. · Nat—Routes generated by NAT.
OrigTblID	Original routing table ID.
TableID	ID of the routing table.
OrigAs	Original AS number.
NibID	ID of the next hop.
LastAs	Last AS number.
AttrID	Attribute ID.
Neighbor	Address of the neighbor determined by the routing protocol.
Flags	Flags of the route.
OrigNextHop	Next hop address of the route.
RealNextHop	Real next hop of the route.
BkNexthop	Backup next hop.
Interface	Output interface for packets to be forwarded along the route.
BkInterface	Backup output interface.
Summary Count	Number of routes.

display ipv6 routing-table acl

Use display ipv6 routing-table acl to display routing information permitted by a specific IPv6 basic ACL.

Syntax

display ipv6 routing-table acl acl-number [ verbose ] [ standby slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

acl6-number: Specifies a basic IPv6 ACL by its number in the range of 2000 to 2999.

verbose: Displays detailed information about all routes permitted by the basic IPv6 ACL. If you do not specify this keyword, the command displays only brief information about active routes permitted by the basic IPv6 ACL.

standby slot slot-number: Displays backup information permitted by the IPv6 basic ACL for an IRF member device. If you do not specify this option, the command displays information permitted by the IPv6 basic ACL.

Usage guidelines

If the specified IPv6 ACL does not exist or has no rules configured, the command displays information about all IPv6 routes.

Examples

# Display brief information about active routes permitted by IPv6 ACL 2000.

<Sysname> display ipv6 routing-table acl 2000

Routes Matched by Access control list : 2000

Summary Count : 3

Destination : ::1/128 Protocol : Direct

NextHop : ::1 Preference: 0

Interface : InLoop0 Cost : 0

Destination : 1:1::/64 Protocol : Static

NextHop : :: Preference: 60

Interface : NULL0 Cost : 0

For command output, see Table 6.

# Display detailed information about all routes permitted by IPv6 ACL 2000.

<Sysname> display ipv6 routing-table acl 2000 verbose

Routes Matched by Access control list : 2000

Summary Count : 3

Destination: ::1/128

Protocol: Direct Process ID: 0

SubProtID: 0x0 Age: 08h57m19s

Cost: 0 Preference: 0

Tag: 0 State: Active NoAdv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0xa OrigAs: 0

NibID: 0x20000000 LastAs: 0

AttrID: 0xffffffff Neighbor: ::

Flags: 0x10004 OrigNextHop: ::1

Label: NULL RealNextHop: ::1

BkLabel: NULL BkNextHop: N/A

Tunnel ID: Invalid Interface: InLoopBack0

BkTunnel ID: Invalid BkInterface: N/A

Destination: 1:1::/64

Protocol: Static Process ID: 0

SubProtID: 0x2 Age: 08h57m19s

Cost: 0 Preference: 60

Tag: 0 State: Active Adv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0xa OrigAs: 0

NibID: 0x20000002 LastAs: 0

AttrID: 0xffffffff Neighbor: ::

Flags: 0x10084 OrigNextHop: ::

Label: NULL RealNextHop: ::

BkLabel: NULL BkNextHop: N/A

Tunnel ID: Invalid Interface: NULL0

BkTunnel ID: Invalid BkInterface: N/A

For command output, see Table 7.

display ipv6 routing-table ipv6-address

Use display ipv6 routing-table ipv6-address to display information about routes to an IPv6 destination address.

Use display ipv6 routing-table ipv6-address1 to ipv6-address2 to display information about routes to a range of IPv6 destination addresses.

Syntax

display ipv6 routing-table ipv6-address [ prefix-length ] [ longer-match ] [ verbose ] [ standby slot slot-number ]

display ipv6 routing-table ipv6-address1 to ipv6-address2 [ verbose ] [ standby slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

ipv6-address: Specifies a destination IPv6 address.

prefix-length: Specifies the prefix length in the range of 0 to 128.

longer-match: Displays the route entry with the longest prefix.

ipv6-address1 to ipv6-address2: Specifies a destination IPv6 address range.

standby slot slot-number: Displays backup information about IPv6 routes for an IRF member device. If you do not specify this option, the command displays information about IPv6 routes.

Usage guidelines

Executing the command with different parameters yields different output.

· display ipv6 routing-table ipv6-address

¡ The system ANDs the entered destination IPv6 address with the prefix length in each active route entry.

¡ The system ANDs the destination IPv6 address in each active route entry with the prefix length in the entry.

If the two operations yield the same result for an entry, this entry is displayed.

· display ipv6 routing-table ipv6-address prefix-length

¡ The system ANDs the entered destination IPv6 address with the entered prefix length.

¡ The system ANDs the destination IPv6 address in each active route entry with the entered prefix length.

If the two operations yield the same result for an entry and the entry has a prefix length less than or equal to the entered prefix length, the entry is displayed.

· display ipv6 routing-table ipv6-address longer-match

¡ The system ANDs the entered destination IPv6 address with the prefix length in each active route entry.

¡ The system ANDs the destination IPv6 address in each active route entry with the prefix length in the entry.

If the two operations yield the same result for multiple entries, the one that has the longest prefix length is displayed.

· display ipv6 routing-table ipv6-address prefix-length longer-match

¡ The system ANDs the entered destination IPv6 address with the entered prefix length.

¡ The system ANDs the destination IPv6 address in each active route entry with the entered prefix length.

If the two operations yield the same result for multiple entries with a prefix length less than or equal to the entered prefix length, the one with the longest prefix length is displayed.

· display ipv6 routing-table ipv6-address1 to ipv6-address2

The system displays route entries with destinations in the range of ipv6-address1/128 to ipv6-address2/128.

Examples

# Display brief information about the routes to the destination IPv6 address 10::1 127.

<Sysname> display ipv6 routing-table 10::1 127

Summary Count: 3

Destination: 10::/64 Protocol : Static

NextHop : :: Preference: 60

Interface : NULL0 Cost : 0

Destination: 10::/68 Protocol : Static

NextHop : :: Preference: 60

Interface : NULL0 Cost : 0

Destination: 10::/120 Protocol : Static

NextHop : :: Preference: 60

Interface : NULL0 Cost : 0

# Display brief information about the most specific route to the destination IPv6 address 10::1 and prefix length 127.

<Sysname> display ipv6 routing-table 10::1 127 longer-match

Summary Count : 1

Destination: 10::/120 Protocol : Static

NextHop : :: Preference: 60

Interface : NULL0 Cost : 0

# Display brief information about the routes to destination addresses in the range of 100:: to 300::.

<Sysname> display ipv6 routing-table 100:: to 300::

Summary Count : 3

Destination: 100::/64 Protocol : Static

NextHop : :: Preference: 60

Interface : NULL0 Cost : 0

Destination: 200::/64 Protocol : Static

NextHop : :: Preference: 60

Interface : NULL0 Cost : 0

Destination: 300::/64 Protocol : Static

NextHop : :: Preference: 60

Interface : NULL0 Cost : 0

For command output, see Table 6.

display ipv6 routing-table prefix-list

Use display ipv6 routing-table prefix-list to display information about IPv6 routes permitted by an IPv6 prefix list.

Syntax

display ipv6 routing-table prefix-list prefix-list-name [ verbose ] [ standby slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

prefix-list-name: Specifies an IPv6 prefix list by its name, a case-sensitive string of 1 to 63 characters.

verbose: Displays detailed information about all IPv6 routes permitted by the IPv6 prefix list. If you do not specify this keyword, the command displays brief information about active IPv6 routes permitted by the IPv6 prefix list.

standby slot slot-number: Displays backup information about IPv6 routes permitted by the IPv6 prefix list for an IRF member device. If you do not specify this option, the command displays information about IPv6 routes permitted by the IPv6 prefix list.

Usage guidelines

If the specified IPv6 prefix list does not exist, the command displays information about all routes.

Examples

# Create an IPv6 prefix list named test to permit the prefix ::1/128.

<Sysname> system-view

[Sysname] ipv6 prefix-list test permit ::1 128

# Display brief information about the active IPv6 route permitted by the IPv6 prefix list.

[Sysname] display ipv6 routing-table prefix-list test

Routes Matched by Prefix list : test

Summary Count : 1

Destination: ::1/128 Protocol : Direct

NextHop : ::1 Preference: 0

Interface : InLoop0 Cost : 0

For command output, see Table 6.

# Display detailed information about all routes permitted by the IPv6 prefix list.

[Sysname] display ipv6 routing-table prefix-list test verbose

Routes Matched by Prefix list : test

Summary Count : 1

Destination: ::1/128

Protocol: Direct Process ID: 0

SubProtID: 0x0 Age: 08h57m19s

Cost: 0 Preference: 0

Tag: 0 State: Active NoAdv

OrigTblID: 0x0 OrigVrf: default-vrf

TableID: 0xa OrigAs: 0

NibID: 0x20000000 LastAs: 0

AttrID: 0xffffffff Neighbor: ::

Flags: 0x10004 OrigNextHop: ::1

Label: NULL RealNextHop: ::1

BkLabel: NULL BkNextHop: N/A

Tunnel ID: Invalid Interface: InLoopBack0

BkTunnel ID: Invalid BkInterface: N/A

For command output, see Table 7.

display ipv6 routing-table protocol

Use display ipv6 routing-table protocol to display information about IPv6 routes installed by a protocol.

Syntax

display ipv6 routing-table protocol protocol [ inactive | verbose ] [ standby slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

protocol: Specifies a routing protocol. It can be bgp4+, direct, isisv6, ospfv3, ripng, or static.

inactive: Displays information about inactive routes. If you do not specify this keyword, the command displays information about both active and inactive routes.

verbose: Displays detailed routing table information. If you do not specify this keyword, the command displays brief routing information.

standby slot slot-number: Displays backup information about IPv6 routes installed by the protocol for an IRF member device. If you do not specify this option, the command displays information about IPv6 routes installed by the protocol.

Examples

# Display brief information about direct routes.

<Sysname> display ipv6 routing-table protocol direct

Summary Count : 3

Direct Routing Table Status : <Active>

Summary Count : 3

Destination: ::1/128 Protocol : Direct

NextHop : ::1 Preference: 0

Interface : InLoop0 Cost : 0

Destination: FE80::/10 Protocol : Direct

NextHop : :: Preference: 0

Interface : NULL0 Cost : 0

Destination: FF00::/8 Protocol : Direct

NextHop : :: Preference: 0

Interface : NULL0 Cost : 0

Direct Routing Table Status : <Inactive>

Summary Count : 0

# Display brief information about static routes.

<Sysname> display ipv6 routing-table protocol static

Summary Count : 3

Static Routing table Status : <Active>

Summary Count : 3

Destination: 2::2/128 Protocol : Static

NextHop : fe80::2 Preference: 60

Interface : Vlan2 Cost : 0

Destination: 2::2/128 Protocol : Static

NextHop : fe80::3 Preference: 60

Interface : Vlan2 Cost : 0

Destination: 3::3/128 Protocol : Static

NextHop : 2::2 Preference: 60

Interface : Vlan2 Cost : 0

Static Routing table Status : <Inactive>

Summary Count : 0

For command output, see Table 6.

display ipv6 routing-table statistics

Use display ipv6 routing-table statistics to display IPv6 route statistics.

Syntax

display ipv6 routing-table statistics [ standby slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

standby slot slot-number: Displays backup IPv6 route statistics for an IRF member device. If you do not specify this option, the command displays IPv6 route statistics.

Examples

# Display IPv6 route statistics for the public network.

<Sysname> display ipv6 routing-table statistics

Total prefixes: 8 Active prefixes: 8

Proto route active added deleted

DIRECT 5 5 5 0

STATIC 3 3 3 0

RIPng 0 0 0 0

OSPFv3 0 0 0 0

IS-ISv6 0 0 0 0

BGP4+ 0 0 0 0

Total 8 8 8 0

Table 8 Command output

Field	Description
Total prefixes	Total number of prefixes.
Active prefixes	Number of active prefixes.
Proto	Protocol that installed the route.
route	Number of routes installed by the protocol.
active	Number of active routes.
added	Number of routes added to the routing table after the router started up or the routing table was cleared most recently.
deleted	Number of routes marked as deleted, which will be cleared after a period.
Total	Total number of routes.

display max-ecmp-num

Use display max-ecmp-num to display the maximum number of ECMP routes.

Syntax

display max-ecmp-num

Views

Any view

Predefined user roles

network-admin

network-operator

Examples

# Display the maximum number of ECMP routes.

<Sysname> display max-ecmp-num

Max-ECMP-Num in use: 6

Max-ECMP-Num at the next reboot: 10

Table 9 Command output

Field	Description
Max-ECMP-Num in use	Maximum number of current ECMP routes in use.
Max-ECMP-Num at the next reboot	Maximum number of ECMP routes at the next reboot of the device.

display rib attribute

Use display rib attribute to display route attribute information in the RIB.

Syntax

display rib attribute [ attribute-id ] [ standby slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

attribute-id: Specifies a route attribute by its ID in the range of 0 to FFFFFFFF.

standby slot slot-number: Displays backup route attribute information in the RIB for an IRF member device. If you do not specify this option, the command displays route attribute information in the RIB.

Examples

# Display route attribute information in the RIB.

<Sysname> display rib attribute

Total number of attribute(s): 10

Detailed information of attribute 0x0:

Flag: 0x0

Protocol: BGP

Address family: IPv4

Reference count: 0

Local preference: 0

Ext-communities number: 26

Ext-communities value: <RT: 1:1> <RT: 2:2> <RT: 3:3> <RT: 123.123.123.123:65535

> <RT: 1234567890:65535> <RT: 123.123.123.123:65534> <RT

: 4:4> <RT: 5:5> <RT: 6:6> <RT: 7:7> <RT: 8:8> <RT: 9:9>

<RT: 10:10> <RT: 10:1> <RT: 10:11> <RT: 10:12> <RT: 10:

13> <RT: 10:14> <RT: 10:15> <RT: 10:16> ...

Communities number: 0

Communities value: N/A

AS-path number: 0

AS-path value: N/A

Detailed information of attribute 0x1:

Flag: 0x0

Protocol: BGP

Address family: IPv4

Reference count: 0

Local preference: 0

Ext-communities number: 1

Ext-communities value: <RT: 1:2>

Communities number: 0

Communities value: N/A

AS-path number: 0

AS-path value: N/A

Table 10 Command output

Field	Description
Protocol	Protocol that generates the attribute.
Ext-communities number	Number of the extended community attribute values.
Ext-communities value	Values of the extended community attribute. This field displays N/A when no value exists, and it can display a maximum of 20 values.
Communities number	Number of the COMMUNITY attribute values.
Communities value	Values of the COMMUNITY attribute. This field displays N/A when no value exists, and it can display a maximum of 20 values.
AS-path number	Number of ASs in the AS_PATH attribute.
AS-path value	Values of the AS_PATH attribute, including AS_SET, AS_SEQUENCE, confederation AS_SET, and confederation AS_SEQUENCE. This field displays N/A when no value exists, and it can display a maximum of 20 values.

display rib graceful-restart

Use display rib graceful-restart to display RIB GR state information.

Syntax

display rib graceful-restart

Views

Any view

Predefined user roles

network-admin

network-operator

Examples

# Display RIB GR state information.

<Sysname> display rib graceful-restart

RIB GR state : Phase2-calculation end

RCOM GR State : Flush end

Protocol GR state:

No. Protocol Lifetime FD State Start/End

--------------------------------------------------

1 DIRECT 100 30 End No/No

2 STATIC 480 34 End No/No

3 OSPF 480 36 End No/No

4 ISIS 480 32 End No/No

5 BGP 480 31 End No/No

6 LDP 480 35 End No/No

7 SLSP 480 29 End No/No

Table 11 Command output

Field	Description
RIB GR state	RIB GR status: · Start—GR starts. · IGP end—All IGP protocols complete GR. · Routing protocol end—All routing protocols complete GR. · NSR-calculation unfinished—NSR has not finished optimal route selection. · Triggering start—All triggered optimal route selection starts. · Triggering end—All triggered optimal route selection completes. · Phase1-calculation end—Optimal route selection phase 1 completes. · All end—All protocols complete GR. · Phase2-calculation end—Optimal route selection phase 1 completes.
RCOM GR state	RCOM GR status: · Start—GR starts. · Routing protocol end—All routing protocols complete GR. · NSR-calculation unfinished—NSR has not finished optimal route selection. · Phase1-calculation end—Optimal route selection phase 1 completes. · Notification end—All routes have been delivered to the route management module. · Phase2-calculation end—Optimal route selection phase 2 completes. · Flush start—Starts to flush routes to the FIB. · Flush end—Completes flushing routes to the FIB.
No.	Protocol number.
Lifetime	Lifetime (in seconds) of routes in the RIB during GR.
FD	Handle between the protocol and the RIB.
State	Protocol GR state: · Init—Initialization state. · Listen—Listening state. · Idle. · Active. · Start—GR starts. · End—GR completes.
Start/End	Message sending state: · No—The message has not been sent. · Yes—The message has been sent.

display rib nib

Use display rib nib to display next hop information in the RIB.

Syntax

display rib nib [ self-originated ] [ nib-id ] [ verbose ] [ standby slot slot-number ]

display rib nib protocol protocol-name [ verbose ] [ standby slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

self-originated: Displays information about next hops of self-originated routes in the RIB.

nib-id: Specifies a NIB by its ID in the range of 1 to FFFFFFFF.

verbose: Displays detailed next hop information in the RIB. If you do not specify this keyword, the command displays brief next hop information in the RIB.

protocol protocol-name: Specifies a protocol by its name, which can be bgp, direct, isis, ospf, rip, or static.

standby slot slot-number: Displays backup next hop information in the RIB for an IRF member device. If you do not specify this option, the command displays next hop information in the RIB.

Examples

# Display brief next hop information in the RIB.

<Sysname> display rib nib

Total number of nexthop(s): 176

NibID: 0x10000000 Sequence: 0

Type: 0x1 Flushed: Yes

UserKey0: 0x0 VrfNthp: 1

UserKey1: 0x0 Nexthop: 0.0.0.0

IFIndex: 0x111 LocalAddr: 0.0.0.0

NibID: 0x10000001 Sequence: 1

Type: 0x1 Flushed: Yes

UserKey0: 0x0 VrfNthp: 1

UserKey1: 0x0 Nexthop: 127.0.0.1

IFIndex: 0x112 LocalAddr: 127.0.0.1

NibID: 0x10000002 Sequence: 2

Type: 0x5 Flushed: Yes

UserKey0: 0x0 VrfNthp: 1

UserKey1: 0x0 Nexthop: 127.0.0.1

IFIndex: 0x112 LocalAddr: 127.0.0.1

NibID: 0x26000000 Sequence: 42

Type: 0x2000 Flushed: Yes

SubNibID: 0x21000023 SubSeq: 35

NthpCnt: 1 Samed: 0

NthpType: IP

SubNibID: 0x21000003 SubSeq: 36

NthpCnt: 1 Samed: 0

NthpType: IP

SubNibID: 0x21000004 SubSeq: 37

NthpCnt: 1 Samed: 0

NthpType: IP

SubNibID: 0x21000005 SubSeq: 38

NthpCnt: 1 Samed: 0

NthpType: IP

...

Table 12 Command output

Field	Description
NibID	ID of the next hop.
Sequence	Sequence number of the next hop.
Type	Type of the next hop.
Flushed	Indicates whether the route with the next hop has been flushed to the FIB.
UserKey0	Reserved data 1.
UserKey1	Reserved data 2.
Nexthop	Next hop address.
IFIndex	Interface index.
LocalAddr	Local interface address.
SubNibID	ID of the sub-next hop.
SubSeq	Sequence number of the sub-next hop.
NthpCnt	Number of sub-next hops.
Samed	Number of the same sub-next hops.
NthpType	Type of the sub-next hop. IP represents IP forwarding.

# Display detailed next hop information in the RIB.

<Sysname> display rib nib verbose

Total number of nexthop(s): 176

NibID: 0x10000000 Sequence: 0

Type: 0x1 Flushed: Yes

UserKey0: 0x0 VrfNthp: 1

UserKey1: 0x0 Nexthop: 0.0.0.0

IFIndex: 0x111 LocalAddr: 0.0.0.0

RefCnt: 6 FlushRefCnt: 2

Flag: 0x84 Version: 1

1 nexthop(s):

PrefixIndex: 0 OrigNexthop: 0.0.0.0

RelyDepth: 0 RealNexthop: 0.0.0.0

Interface: NULL0 LocalAddr: 0.0.0.0

TunnelCnt: 0 Vrf: vpn1

TunnelID: N/A

NibID: 0x10000001 Sequence: 1

Type: 0x1 Flushed: Yes

UserKey0: 0x0 VrfNthp: 1

UserKey1: 0x0 Nexthop: 127.0.0.1

IFIndex: 0x112 LocalAddr: 127.0.0.1

RefCnt: 13 FlushRefCnt: 5

Flag: 0x84 Version: 1

1 nexthop(s):

PrefixIndex: 0 OrigNexthop: 127.0.0.1

RelyDepth: 0 RealNexthop: 127.0.0.1

Interface: InLoop0 LocalAddr: 127.0.0.1

TunnelCnt: 0 Vrf: vpn1

TunnelID: N/A

NibID: 0x15000003 Sequence: 3

Type: 0x43 Flushed: Yes

UserKey0: 0x100010000 VrfNthp: 0

UserKey1: 0x0 Nexthop: 22.22.22.22

IFIndex: 0x0 LocalAddr: 0.0.0.0

RefCnt: 9 FlushRefCnt: 3

Flag: 0x84 Version: 1

Policy: tnl-policy1

1 nexthop(s):

PrefixIndex: 0 OrigNexthop: 22.22.22.22

RelyDepth: 1 RealNexthop: 13.1.1.2

Interface: GE0/1/3 LocalAddr: 13.1.1.1

TunnelCnt: 1 Vrf: default-vrf

TunnelID: 1025

NibID: 0x16000000 Sequence: 0

Type: 0x2000 Flushed: Yes

SubNibID: 0x11000009 SubSeq: 13

NthpCnt: 1 Samed: 0

NthpType: IP

SubNibID: 0x1100000d SubSeq: 14

NthpCnt: 1 Samed: 0

NthpType: IP

2 nexthop(s):

PrefixIndex: 0 OrigNexthop: 10.1.1.2

RelyDepth: 0 RealNexthop: 10.1.1.2

Interface: Vlan10 LocalAddr: 10.1.1.1

TunnelCnt: 0 Vrf: default-vrf

TunnelID: N/A

PrefixIndex: 1 OrigNexthop: 11.1.1.2

RelyDepth: 0 RealNexthop: 11.1.1.2

Interface: Vlan11 LocalAddr: 11.1.1.1

TunnelCnt: 0 Vrf: default-vrf

TunnelID: N/A

...

Table 13 Command output

Field	Description
x nexthop (s)	Number of next hops.
PrefixIndex	Prefix index of the next hop for an ECMP route.
OrigNexthop	Original next hop.
RealNexthop	Real next hop.
Interface	Output interface.
LocalAddr	Local interface address.
RelyDepth	Recursion depth.
RefCnt	Reference count of the next hop.
FlushRefCnt	Reference count of the next hop that is flushed to the FIB.
Flag	Flag of the next hop.
Version	Version of the next hop.

display route-direct nib

Use display route-direct nib to display next hop information for direct routes.

Syntax

display route-direct nib [ nib-id ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

nib-id: Specifies a NIB by its ID in the range of 1 to FFFFFFFF.

verbose: Displays detailed next hop information for direct routes. If you do not specify this keyword, the command displays brief next hop information for direct routes.

Examples

# Display brief next hop information for direct routes.

<Sysname> display route-direct nib

Total number of nexthop(s): 116

NibID: 0x10000000 Sequence: 0

Type: 0x1 Flushed: Yes

UserKey0: 0x0 VrfNthp: 1

UserKey1: 0x0 Nexthop: 0.0.0.0

IFIndex: 0x111 LocalAddr: 0.0.0.0

NibID: 0x10000001 Sequence: 1

Type: 0x1 Flushed: Yes

UserKey0: 0x0 VrfNthp: 1

UserKey1: 0x0 Nexthop: 127.0.0.1

IFIndex: 0x112 LocalAddr: 127.0.0.1

...

Table 14 Command output

Field	Description
NibID	ID of the NIB.
Sequence	Sequence number of the NIB.
Type	Type of the NIB.
Flushed	Indicates whether the route with the NIB has been flushed to the FIB.
UserKey0	Reserved data 1.
UserKey1	Reserved data 2.
Nexthop	Next hop address.
IFIndex	Interface index.

# Display detailed next hop information for direct routes.

<Sysname> display route-direct nib verbose

Total number of nexthop(s): 116

NibID: 0x10000000 Sequence: 0

Type: 0x1 Flushed: Yes

UserKey0: 0x0 VrfNthp: 1

UserKey1: 0x0 Nexthop: 0.0.0.0

IFIndex: 0x111 LocalAddr: 0.0.0.0

RefCnt: 2 FlushRefCnt: 0

Flag: 0x2 Version: 1

1 nexthop(s):

PrefixIndex: 0 OrigNexthop: 0.0.0.0

RelyDepth: 0 RealNexthop: 0.0.0.0

Interface: NULL0 LocalAddr: 0.0.0.0

TunnelCnt: 0 Vrf: vpn1

TunnelID: N/A

NibID: 0x10000001 Sequence: 1

Type: 0x1 Flushed: Yes

UserKey0: 0x0 VrfNthp: 1

UserKey1: 0x0 Nexthop: 127.0.0.1

IFIndex: 0x112 LocalAddr: 127.0.0.1

RefCnt: 5 FlushRefCnt: 0

Flag: 0x2 Version: 1

1 nexthop(s):

PrefixIndex: 0 OrigNexthop: 127.0.0.1

RelyDepth: 0 RealNexthop: 127.0.0.1

Interface: InLoop0 LocalAddr: 127.0.0.1

TunnelCnt: 0 Vrf: vpn1

TunnelID: N/A

...

Table 15 Command output

Field	Description
x nexthop(s)	Number of next hops.
PrefixIndex	Prefix index of the next hop for an ECMP route.
OrigNexthop	Original next hop.
RealNexthop	Real next hop.
Interface	Output interface.
localAddr	Local interface address.
RelyDepth	Recursion depth.
RefCnt	Reference count of the next hop.
FlushRefCnt	Reference count of the next hop that is flushed to the FIB.
Flag	Flag of the next hop.
Version	Version of the next hop.

display switch-routing-mode status

Use display switch-routing-mode status to display the status of IPv6 routes with prefixes longer than 64 bits.

Syntax

display switch-routing-mode status

Views

Any view

Predefined user roles

network-admin

network-operator

Examples

# Display the status of IPv6 routes with prefixes longer than 64 bits.

<Sysname> display switch-routing-mode status

Switch-routing-mode in use: ipv6-128 supported.

Switch-routing-mode at the next reboot: ipv6-128 supported.

ecmp mode enhanced

Use ecmp mode enhanced to enable the enhanced ECMP mode.

Use undo ecmp mode to restore the default.

Syntax

ecmp mode enhanced

undo ecmp mode

Default

The enhanced ECMP mode is disabled.

Views

System view

Predefined user roles

network-admin

Examples

# Enable the enhanced ECMP mode.

<Sysname> system-view

[Sysname] ecmp mode enhanced

The configuration will take effect at the next reboot. Continue? [Y/N]:y

Reboot device to make the configuration take effect.

fib lifetime

Use fib lifetime to set the maximum lifetime for IPv4 or IPv6 routes in the FIB.

Use undo fib lifetime to restore the default.

Syntax

fib lifetime seconds

undo fib lifetime

Default

The maximum lifetime for IPv4 or IPv6 routes in the FIB is 600 seconds.

Views

RIB IPv4 address family view, RIB IPv6 address family view

Predefined user roles

network-admin

Parameters

seconds: Sets the maximum lifetime for routes in the FIB, in the range of 0 to 900 seconds. When this argument is set to 0, FIB entries immediately age out after a protocol or RIB process switchover.

Usage guidelines

When a protocol or RIB process switchover occurs and GR or NSR is not configured, FIB entries age out after the time specified in this command.

Examples

# Set the maximum lifetime for IPv4 routes in the FIB to 60 seconds.

<Sysname> system-view

[Sysname] rib

[Sysname-rib] address-family ipv4

[Sysname-rib-ipv4] fib lifetime 60

max-ecmp-num

Use max-ecmp-num to set the maximum number of ECMP routes.

Syntax

max-ecmp-num number

Default

The maximum number of ECMP routes is 8.

Views

System view

Predefined user roles

network-admin

Parameters

number: Specifies the maximum number of ECMP routes, in the range of 1 to 32.

Usage guidelines

When one or multiple ECMP routes fail, the default ECMP mode enables the device to reallocate all traffic to the remaining routes.

The enhanced ECMP mode enables the device to reallocate only the traffic of the failed routes to the remaining routes.

Examples

# Set the maximum number of ECMP routes to 10.

<Sysname> system-view

[Sysname] max-ecmp-num 10

The configuration will take effect at the next reboot. Continue? [Y/N]:y

Reboot device to make the configuration take effect.

After reboot, the maximum number of ECMP routes is 10.

protocol lifetime

Use protocol lifetime to set the maximum lifetime for IPv4 or IPv6 routes in the RIB.

Use undo protocol lifetime to restore the default.

Syntax

protocol protocol lifetime seconds

undo protocol protocol lifetime

Default

The maximum lifetime for IPv4 or IPv6 routes in the RIB is 480 seconds.

Views

RIB IPv4 address family view, RIB IPv6 address family view

Predefined user roles

network-admin

Parameters

seconds: Sets the maximum lifetime for routes in the RIB, in the range of 0 to 900 seconds. When this argument is set to 0, RIB entries immediately age out when a protocol switchover occurs.

Usage guidelines

When GR is enabled, make sure the protocol can complete GR and install all route entries to the RIB within the lifetime configured in this command.

Examples

# Set the maximum lifetime for OSPF routes in the RIB to 60 seconds.

<Sysname> system-view

[Sysname] rib

[Sysname-rib] address-family ipv4

[Sysname-rib-ipv4] protocol ospf lifetime 60

reset ip routing-table statistics protocol

Use reset ip routing-table statistics protocol to clear IPv4 route statistics.

Syntax

reset ip routing-table statistics protocol { protocol | all } [ standby slot slot-number ]

Views

User view

Predefined user roles

network-admin

Parameters

protocol: Clears route statistics for a routing protocol. It can be bgp, direct, isis, ospf, rip, or static.

all: Clears route statistics for all IPv4 routing protocols.

standby slot slot-number: Clears backup IPv4 route statistics for an IRF member device. If you do not specify this option, the command clears IPv4 route statistics.

Examples

# Clear all IPv4 route statistics for the public network.

<Sysname> reset ip routing-table statistics protocol all

reset ipv6 routing-table statistics protocol

Use reset ipv6 routing-table statistics protocol to clear IPv6 route statistics.

Syntax

reset ipv6 routing-table statistics protocol { protocol | all } [ standby slot slot-number ]

Views

User view

Predefined user roles

network-admin

Parameters

protocol: Clears route statistics for an IPv6 routing protocol. It can be bgp4+, direct, isisv6, ospfv3, ripng, or static.

all: Clears route statistics for all IPv6 routing protocols.

standby slot slot-number: Clears backup IPv6 route statistics for an IRF member device. If you do not specify this option, the command clears IPv6 route statistics.

Examples

# Clear all IPv6 route statistics for the public network.

<Sysname> reset ipv6 routing-table statistics protocol all

rib

Use rib to enter RIB view.

Use undo rib to remove all configurations in RIB view.

Syntax

rib

undo rib

Views

System view

Predefined user roles

network-admin

Examples

# Enter RIB view.

<Sysname> system-view

[Sysname] rib

[Sysname-rib]

switch-routing-mode ipv6-128

Use switch-routing-mode ipv6-128 to enable support for IPv6 routes with prefixes longer than 64 bits.

Use undo switch-routing-mode ipv6-128 to disable support for IPv6 routes with prefixes longer than 64 bits.

Syntax

switch-routing-mode ipv6-128

undo switch-routing-mode ipv6-128

Default

The device does not support IPv6 routes with prefixes longer than 64 bits.

Views

System view

Predefined user roles

network-admin

Usage guidelines

This command takes effect at next reboot. Make sure the reboot does not impact your network.

Examples

# Enable support for IPv6 routes with prefixes longer than 64 bits.

<Sysname> system-view

[Sysname] switch-routing-mode ipv6-128

Reboot device to make the configuration take effect.

05-Layer 3-IP Routing Command Reference

display ip routing-table acl

display ip routing-table ip-address

display ip routing-table prefix-list

display ip routing-table statistics

display ipv6 rib attribute

display ipv6 routing-table acl

display ipv6 routing-table ipv6-address

reset ipv6 routing-table statistics protocol

Intelligent Terminal Products

Product Support Services

Technical Service Solutions

Resource Center

Policy

Online Help

Become a Partner

Partner Policy & Program

Global Learning

Partner Sales Resources

Service Business

News & Events

Contact Us