With this feature configured, CDP frames sent to IP phones from the interface carries the configured voice VLAN ID. IP phones use the voice VLAN ID to send voice traffic.

Examples

# Set the voice VLAN ID carried in CDP frames to 100.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] cdp voice-vlan 100

dcbx version

Use dcbx version to set the DCBX version.

Use undo dcbx version to restore the default.

Syntax

dcbx version { rev100 | rev101 | standard }

undo dcbx version

Default

The DCBX version is not configured. It is autonegotiated by the local port and peer port.

Views

Layer 2 Ethernet interface view

Predefined user roles

network-admin

mdc-admin

Parameters

rev100: Specifies DCBX Rev 1.00.

rev101: Specifies DCBX Rev 1.01.

standard: Specifies the IEEE Std 802.1Qaz-2011.

Usage guidelines

For DCBX to work correctly, set the same DCBX version on the local port and peer port. As a best practice, set the highest version supported on both ends. IEEE Std 802.1Qaz-2011, DCBX Rev 1.01, and DCBX Rev 1.00 are in descending order.

After the configuration, LLDP frames sent by the local port carry information about the configured DCBX version. The local port and peer port do not negotiate the DCBX version.

When the DCBX version is autonegotiated, the version IEEE Std 802.1Qaz-2011 is preferentially negotiated.

Examples

# Set the DCBX version to Rev. 1.01 on interface GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] dcbx version rev101

Related commands

lldp tlv-enable

display lldp local-information

Use display lldp local-information to display local LLDP information, which will be contained in the advertisable LLDP TLVs and sent to neighboring devices.

Syntax

display lldp local-information [ global | interface interface-type interface-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

global: Displays the global local LLDP information.

interface interface-type interface-number: Specifies a port by its type and number.

Usage guidelines

If you do not specify any keywords or arguments, the command displays all local LLDP information, which includes the following:

· The global LLDP information.

· The LLDP information about the LLDP-enabled ports in up state.

Examples

# Display all local LLDP information. (In this example, the DCBX version is IEEE Std 802.1Qaz-2011.)

<Sysname> display lldp local-information

Global LLDP local-information:

Chassis ID : 0000-fc00-2500

System name : H3C

System description : H3C Comware Platform Software, Software Version 7.1.045,

Release 7150

H3C S10506

rights reserved.

System capabilities supported : Bridge, Router, Customer Bridge, Service Bridge

System capabilities enabled : Bridge, Router, Customer Bridge

MED information:

Device class : Connectivity device

MED inventory information of master board:

HardwareRev : VER.A

FirmwareRev : 006

SoftwareRev : 7.1.045714101

SerialNum : Unknown

Manufacturer name : Unknown

Model name : H3C S10506

Asset tracking identifier : Unknown

LLDP local-information of port 296[GigabitEthernet3/0/5]:

Port ID type : Interface name

Port ID : GigabitEthernet3/0/5

Port description : GigabitEthernet3/0/5 Interface

LLDP agent nearest-bridge management address:

Management address type : IPv4

Management address : 12.12.12.1

Management address interface type : IfIndex

Management address interface ID : 18949

Management address OID : 0

LLDP agent nearest-nontpmr management address:

Management address type : IPv4

Management address : 12.12.12.1

Management address interface type : IfIndex

Management address interface ID : 18949

Management address OID : 0

LLDP agent nearest-customer management address:

Management address type : IPv4

Management address : 12.12.12.1

Management address interface type : IfIndex

Management address interface ID : 18949

Management address OID : 0

DCBX Control info:

Oper version : Standard

DCBX PFC info:

P0-0 P1-0 P2-0 P3-0 P4-0 P5-0 P6-0 P7-0

Number of traffic classes supported: 8

Value of MBC: 0

Port VLAN ID(PVID) : 57

Port and protocol VLAN ID(PPVID) : 0

Port and protocol VLAN supported : No

Port and protocol VLAN enabled : No

VLAN name of VLAN 57 : VLAN 0057

Management VLAN ID : 0

Link aggregation supported : Yes

Link aggregation enabled : No

Aggregation port ID : 0

Auto-negotiation supported : Yes

Auto-negotiation enabled : Yes

OperMau : Speed(1000)/Duplex(Full)

Power port class : PD

PSE power supported : No

PSE power enabled : Yes

PSE pairs control ability : No

Power pairs : Signal

Port power classification : Unknown

Maximum frame size : 9216

Media policy type : Voice

Unknown policy : No

VLAN tagged : Yes

Media policy VLAN ID : 0

Media policy L2 priority : 0

Media policy DSCP : 0

LLDP local-information of port 315[GigabitEthernet3/0/24]:

Port ID type : Interface name

Port ID : GigabitEthernet3/0/24

Port description : GigabitEthernet3/0/24 Interface

LLDP agent nearest-bridge management address:

Management address type : IPv4

Management address : 192.168.10.1

Management address interface type : IfIndex

Management address interface ID : 315

Management address OID : 0

LLDP agent nearest-nontpmr management address:

Management address type : IPv4

Management address : 192.168.10.1

Management address interface type : IfIndex

Management address interface ID : 315

Management address OID : 0

LLDP agent nearest-customer management address:

Management address type : IPv4

Management address : 192.168.10.1

Management address interface type : IfIndex

Management address interface ID : 315

Management address OID : 0

Link aggregation supported : Yes

Link aggregation enabled : No

Aggregation port ID : 0

Auto-negotiation supported : Yes

Auto-negotiation enabled : Yes

OperMau : Speed(1000)/Duplex(Full)

Power port class : PD

PSE power supported : No

PSE power enabled : Yes

PSE pairs control ability : No

Power pairs : Signal

Port power classification : Unknown

Maximum frame size : 1500

Table 1 Command output

Field	Description
Chassis ID	Bridge MAC address of the device.
System capabilities supported	Supported capabilities: · Bridge—Switching is supported. · Router—Routing is supported. · WlanAccessPoint—The local device can serve as a wireless AP. · Telephone—The local device can serve as a telephone. · DocsisCableDevice—The local device can serve as a DOCSIS-compliant cable device. · StationOnly—The local device can serve as a station only. · Customer Bridge—The customer bridge function is supported. · Service Bridge—The service bridge function is supported. · TPMR—The TPMR function is supported. · Other—Functions other than those listed above are supported.
System capabilities enabled	Enabled capabilities: · Bridge—Switching is enabled. · Router—Routing is enabled. · WlanAccessPoint—The local device is serving as a wireless AP. · Telephone—The local device is serving as a telephone. · DocsisCableDevice—The local device is serving as a DOCSIS-compliant cable device. · StationOnly—The local device is serving as a station only. · Customer Bridge—The customer bridge function is enabled. · Service Bridge—The service bridge function is enabled. · TPMR—The TPMR function is enabled. · Other—Functions other than those listed above are enabled.
Device class	MED device class: · Connectivity device—Network device. · Class I—Normal terminal device. It requires the basic LLDP discovery services. · Class II—Media terminal device. It supports media streams, and can also function as a normal terminal device. · Class III—Communication terminal device. It supports the IP communication systems of end users, and can also function as a normal terminal device or media terminal device.
HardwareRev	Hardware version.
FirmwareRev	Firmware version.
SoftwareRev	Software version.
SerialNum	Serial number.
Manufacturer name	Device manufacturer.
Model name	Device model.
Port ID type	Port ID type: · MAC address. · Interface name.
Port ID	Port ID, the value of which depends on the port ID type.
Management address interface type	Numbering type of the interface identified by the management address.
Management address interface ID	Index of the interface identified by the management address.
Management address OID	Management address object ID.
DCBX Control info	Displayed as version information in IEEE Std 802.1Qaz-2011.
Oper version	DCBX version number.
Percentage	Percentage of bandwidth allocated.
DCBX PFC info	DCBX PFC TLV information.
P0- P1- P2- P3- P4- P5- P6- P7-	Number of supported priorities configured by using the priority-flow-control no-drop dot1p dot1p-list command at the local end.
Number of traffic classes supported	Number of traffic classes supported by PFC (displayed only in Rev 1.01).
Value of MBC	MBC indicates the ability of packets to bypass MACsec. It is 1-bit long. · 0—Packets can bypass MACsec when MACsec is disabled. · 1—Packets cannot bypass MACsec when MACsec is disabled.
Port and protocol VLAN supported	Indicates whether port and protocol VLAN is supported on the port.
Port and protocol VLAN enabled	Indicates whether port and protocol VLAN is enabled on the port.
Link aggregation supported	Indicates whether link aggregation is supported on the port.
Link aggregation enabled	Indicates whether link aggregation is enabled on the port.
Aggregation port ID	ID of the port in the aggregation group. This field displays 0 when link aggregation is disabled.
Auto-negotiation supported	Indicates whether autonegotiation is supported on the port.
Auto-negotiation enabled	Indicates whether autonegotiation is enabled on the port.
OperMau	Speed and duplex state of the port.
Power port class	PoE port class: · PSE—Power sourcing equipment. · PD—Powered device.
PSE power supported	Indicates whether the device can operate as a PSE.
PSE power enabled	Indicates whether the device is operating as a PSE.
PSE pairs control ability	Indicates whether the pair selection ability is available.
Power pairs	Power supply mode: · Signal—Uses data pairs to supply power. · Spare—Uses spare pairs to supply power.
Port power classification	Power class of the PD: · Class 0. · Class 1. · Class 2. · Class 3. · Class 4.
Media policy type	Media policy type: · unknown. · voice. · voiceSignaling. · guestVoice. · guestVoiceSignaling. · softPhoneVoice. · videoconferencing. · streamingVideo. · videoSignaling.
Unknown policy	Indicates whether the media policy is unknown.
VLAN tagged	Indicates whether packets of the media VLAN are tagged.
Media policy VLANID	ID of the media VLAN.
Media policy L2 priority	Layer 2 priority.
Media policy DSCP	DSCP value.

display lldp neighbor-information

Use display lldp neighbor-information to display the LLDP information carried in LLDP TLVs that the local device receives from the neighboring devices.

Syntax

display lldp neighbor-information [ [ [ interface interface-type interface-number ] [ agent { nearest-bridge | nearest-customer | nearest-nontpmr } ] [ verbose ] ] | list [ system-name system-name ] ]

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

interface interface-type interface-number: Specifies a port by its type and number. If this option is not specified, this command displays the LLDP information that all ports receive from the neighboring devices.

agent: Specifies an agent type. If you do not specify an agent type, the command displays the LLDP information that all LLDP agents receive from the neighboring devices.

nearest-bridge: Specifies nearest bridge agents.

nearest-customer: Specifies nearest customer bridge agents.

nearest-nontpmr: Specifies nearest non-TPMR bridge agents.

verbose: Displays the detailed LLDP information that the local device receives from the neighboring devices. If this keyword is not specified, this command displays the brief LLDP information that the local device receives from the neighboring devices.

list: Displays the LLDP information that the local device receives from the neighboring devices in the form of a list.

system-name system-name: Displays the LLDP information that the local device receives from a neighboring device specified by its system name. The system-name argument is a string of 1 to 255 characters. If this option is not specified, this command displays the LLDP information that the local device receives from all neighboring devices in a list.

Examples

# Display the detailed LLDP information that the nearest bridge agents on all ports received from the neighboring devices. (DCBX is IEEE Std 802.1Qaz-2011.)

<Sysname> display lldp neighbor-information agent nearest-bridge verbose

LLDP neighbor-information of port 315[GigabitEthernet3/0/24]:

LLDP agent nearest-bridge:

LLDP neighbor index : 1

Update time : 0 days, 7 hours, 34 minutes, 6 seconds

Chassis type : MAC address

Chassis ID : 0000-fc00-2500

Port ID type : Interface name

Port ID : GigabitEthernet3/0/24

Time to live : 121

Port description : GigabitEthernet3/0/24 Interface

System name : Sysname

System description : H3C Comware Platform Software, Software Version 7.1.045,

Alpha 714101

H3C S10506

rights reserved.

System capabilities supported : Bridge, Router, Customer Bridge, Service Bridge

System capabilities enabled : Bridge, Router, Customer Bridge

Management address type : IPv4

Management address : 192.168.10.1

Management address interface type : IfIndex

Management address interface ID : 315

Management address OID : 0

Link aggregation supported : Yes

Link aggregation enabled : No

Aggregation port ID : 0

Auto-negotiation supported : Yes

Auto-negotiation enabled : Yes

OperMau : Speed(1000)/Duplex(Full)

Power port class : PD

PSE power supported : No

PSE power enabled : Yes

PSE pairs control ability : No

Power pairs : Signal

Port power classification : Unknown

Maximum frame size : 1500

# Display the brief LLDP information that all LLDP agents on all ports received from the neighboring devices.

<Sysname> display lldp neighbor-information

LLDP neighbor-information of port 315[GigabitEthernet3/0/24]:

LLDP agent nearest-bridge:

LLDP neighbor index : 1

ChassisID/subtype : 0000-fc00-2500/MAC address

PortID/subtype : GigabitEthernet3/0/24/Interface name

Capabilities : Bridge, Router, Customer Bridge

# Display the brief LLDP information that all LLDP agents received from all neighboring devices in a list.

<Sysname> display lldp neighbor-information list

Chassis ID : * -- --Nearest nontpmr bridge neighbor

# -- --Nearest customer bridge neighbor

Default -- -- Nearest bridge neighbor

System Name Local Interface Chassis ID Port ID

System1 GE1/0/1 000f-e25d-ee91 GigabitEthernet1/0/5

System2 GE1/0/2 000f-e25d-ee92* GigabitEthernet1/0/6

System3 GE1/0/3 000f-e25d-ee93# GigabitEthernet1/0/7

Table 2 Command output

Field	Description
LLDP neighbor-information of port	LLDP information received through the port.
Update time	Time when LLDP information about a neighboring device was last updated.
Chassis type	Chassis ID type: · Chassis component. · Interface alias. · Port component. · MAC address. · Network address (ipv4). · Interface name. · Locally assigned—Locally-defined chassis type other than those listed above.
Chassis ID	ID that identifies the LLDP sending device, which can be a MAC address, a network address, an interface, or some other value, depending on the chassis ID type of the neighboring device.
Port ID type	Port ID type: · Interface alias. · Port component. · MAC address. · Network address (ipv4). · Interface name. · Agent circuit ID. · Locally assigned—Locally-defined port ID type other than those listed above.
Port ID	Value of the type of the port ID.
System name	System name of the neighboring device.
System description	System description of the neighboring device.
System capabilities supported	Capabilities supported on the neighboring device: · Repeater—Signal repeating is supported. · Bridge—Switching is supported. · WlanAccessPoint—The neighboring device can serve as a wireless AP. · Router—Routing is supported. · Telephone—The neighboring device can serve as a telephone. · DocsisCableDevice—The neighboring device can serve as a DOCSIS-compliant cable device. · StationOnly—The neighboring device can serve as a station only. · Customer Bridge—The customer bridge function is enabled. · Service Bridge—The service bridge function is enabled. · TPMR—The TPMR function is enabled. · Other—Functions other than those listed above are supported.
System capabilities enabled	Capabilities enabled on the neighboring device: · Repeater—Signal repeating is enabled. · Bridge—Switching is enabled. · WlanAccessPoint—The neighboring device is serving as a wireless AP. · Router—Routing is enabled. · Telephone—The neighboring device is serving as a telephone. · DocsisCableDevice—The neighboring device is serving as a DOCSIS-compliant cable device. · StationOnly—The neighboring device is serving as a station only. · Customer Bridge—The customer bridge function is enabled. · Service Bridge—The service bridge function is enabled. · TPMR—The TPMR function is enabled. · Other—Functions other than those listed above are supported.
Management address OID	Management address object ID.
Link aggregation supported	Indicates whether link aggregation is supported on the port.
Link aggregation enabled	Indicates whether link aggregation is enabled on the port.
Aggregation port ID	ID of the port in the aggregation group. This field displays 0 when link aggregation is disabled.
Auto-negotiation supported	Indicates whether autonegotiation is supported on the port.
Auto-negotiation enabled	Indicates whether autonegotiation is enabled on the port.
OperMau	Speed and duplex state on the port.
Power port class	PoE port class: · PSE—Power sourcing equipment. · PD—Powered device.
PSE power supported	Indicates whether the device can operate as a PSE.
PSE power enabled	Indicates whether the device is operating as a PSE.
PSE pairs control ability	Indicates whether the pair selection ability is available.
Power pairs	Power supply mode: · Signal—Uses data pairs to supply power. · Spare—Uses spare pairs to supply power.
Port power classification	Power class of the PD: · Class 0. · Class 1. · Class 2. · Class 3. · Class 4.

display lldp statistics

Use display lldp statistics to display the global LLDP statistics or the LLDP statistics of a port.

Syntax

display lldp statistics [ global | [ interface interface-type interface-number ] [ agent { nearest-bridge | nearest-customer | nearest-nontpmr } ] ]

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

global: Displays the global LLDP statistics.

interface interface-type interface-number: Specifies a port by its type and number.

agent: Specifies an LLDP agent type. If you do not specify an agent type, the command displays the statistics for all LLDP agents.

nearest-bridge: Specifies nearest bridge agents.

nearest-customer: Specifies nearest customer bridge agents.

nearest-nontpmr: Specifies nearest non-TPMR bridge agents.

Usage guidelines

If you do not specify any keywords or arguments, the command displays the global LLDP statistics and the LLDP statistics of all ports.

Examples

# Display the global LLDP statistics and the LLDP statistics of all ports.

<Sysname> display lldp statistics

LLDP statistics global information:

LLDP neighbor information last change time:0 days, 0 hours, 4 minutes, 40 seconds

The number of LLDP neighbor information inserted : 1

The number of LLDP neighbor information deleted : 1

The number of LLDP neighbor information dropped : 0

The number of LLDP neighbor information aged out : 1

LLDP statistics information of port 1 [GigabitEthernet1/0/1]:

LLDP agent nearest-bridge:

The number of LLDP frames transmitted : 0

The number of LLDP frames received : 0

The number of LLDP frames discarded : 0

The number of LLDP error frames : 0

The number of LLDP TLVs discarded : 0

The number of LLDP TLVs unrecognized : 0

The number of LLDP neighbor information aged out : 0

The number of CDP frames transmitted : 0

The number of CDP frames received : 0

The number of CDP frames discarded : 0

The number of CDP error frames : 0

LLDP agent nearest-nontpmr:

The number of LLDP frames transmitted : 0

The number of LLDP frames received : 0

The number of LLDP frames discarded : 0

The number of LLDP error frames : 0

The number of LLDP TLVs discarded : 0

The number of LLDP TLVs unrecognized : 0

The number of LLDP neighbor information aged out : 0

The number of CDP frames transmitted : 0

The number of CDP frames received : 0

The number of CDP frames discarded : 0

The number of CDP error frames : 0

LLDP agent nearest-customer:

The number of LLDP frames transmitted : 0

The number of LLDP frames received : 0

The number of LLDP frames discarded : 0

The number of LLDP error frames : 0

The number of LLDP TLVs discarded : 0

The number of LLDP TLVs unrecognized : 0

The number of LLDP neighbor information aged out : 0

The number of CDP frames transmitted : 0

The number of CDP frames received : 0

The number of CDP frames discarded : 0

The number of CDP error frames : 0

…

# Display the LLDP statistics for the nearest customer bridge agents on GigabitEthernet 1/0/1.

<Sysname> display lldp statistics interface GigabitEthernet1/0/1 agent nearest-customer

LLDP statistics information of port 1 [GigabitEthernet1/0/1]:

LLDP agent nearest-customer:

The number of LLDP frames transmitted : 0

The number of LLDP frames received : 0

The number of LLDP frames discarded : 0

The number of LLDP error frames : 0

The number of LLDP TLVs discarded : 0

The number of LLDP TLVs unrecognized : 0

The number of LLDP neighbor information aged out : 0

The number of CDP frames transmitted : 0

The number of CDP frames received : 0

The number of CDP frames discarded : 0

The number of CDP error frames : 0

Table 3 Command output

Field	Description
LLDP statistics global information	Global LLDP statistics.
LLDP neighbor information last change time	Time when the neighbor information was last updated.
The number of LLDP neighbor information inserted	Number of times neighbor information was added.
The number of LLDP neighbor information deleted	Number of times neighbor information was removed.
The number of LLDP neighbor information dropped	Number of times neighbor information was dropped due to lack of available memory space.

display lldp status

Use display lldp status to display LLDP status.

Syntax

display lldp status [ interface interface-type interface-number ] [ agent { nearest-bridge | nearest-customer | nearest-nontpmr } ]

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

interface interface-type interface-number: Specifies a port by its type and number. If you do not specify this option, the command displays the global LLDP status and the LLDP status of each port.

agent: Specifies an LLDP agent type. If you do not specify an agent type, the command displays the status information for all LLDP agents.

nearest-bridge: Specifies nearest bridge agents.

nearest-customer: Specifies nearest customer bridge agents.

nearest-nontpmr: Specifies nearest non-TPMR bridge agents.

Examples

# Display the global LLDP status and the LLDP status information of each port.

<Sysname> display lldp status

Global status of LLDP: Enable

Bridge mode of LLDP: customer-bridge

The current number of LLDP neighbors: 0

The current number of CDP neighbors: 0

LLDP neighbor information last changed time: 0 days, 0 hours, 4 minutes, 40 seconds

Transmit interval : 30s

Fast transmit interval : 1s

Transmit max credit : 5

Hold multiplier : 4

Reinit delay : 2s

Trap interval : 5s

Fast start times : 3

LLDP status information of port 1 [GigabitEthernet1/0/1]:

LLDP agent nearest-bridge:

Port status of LLDP : Enable

Admin status : Tx_Rx

Trap flag : No

MED trap flag : No

Polling interval : 0s

Number of LLDP neighbors : 5

Number of MED neighbors : 2

Number of CDP neighbors : 0

Number of sent optional TLV : 12

Number of received unknown TLV : 5

LLDP agent nearest-nontpmr:

Port status of LLDP : Enable

Admin status : Tx_Rx

Trap flag : No

Polling interval : 0s

Number of LLDP neighbors : 5

Number of MED neighbors : 2

Number of CDP neighbors : 0

Number of sent optional TLV : 12

Number of received unknown TLV : 5

LLDP agent nearest-customer:

Port status of LLDP : Enable

Admin status : Tx_Rx

Trap flag : No

Polling interval : 0s

Number of LLDP neighbors : 5

Number of MED neighbors : 2

Number of CDP neighbors : 0

Number of sent optional TLV : 12

Number of received unknown TLV : 5

Table 4 Command output

Field	Description
Bridge mode of LLDP	LLDP bridge mode: service-bridge or customer-bridge.
Global status of LLDP	Indicates whether LLDP is globally enabled.
LLDP neighbor information last changed time	Time when the neighbor information was last updated.
Transmit interval	LLDP frame transmission interval.
Hold multiplier	TTL multiplier.
Reinit delay	LLDP reinitialization delay.
Transmit max credit	Token bucket size for sending LLDP frames.
Trap interval	Trap transmission interval.
Fast start times	Number of LLDP frames sent each time fast LLDP frame transmission is triggered.
Port 1	LLDP status of port 1.
Port status of LLDP	Indicates whether LLDP is enabled on the port.
Admin status	LLDP operating mode of the port: · Tx_Rx—The port can send and receive LLDP frames. · Rx_Only—The port can only receive LLDP frames. · Tx_Only—The port can only send LLDP frames. · Disable—The port cannot send or receive LLDP frames.
Trap Flag	Indicates whether trapping is enabled.
Polling interval	LLDP polling interval, which is 0 when LLDP polling is disabled.
Number of neighbors	Number of LLDP neighbors connecting to the port.
Number of MED neighbors	Number of MED neighbors connecting to the port.
Number of CDP neighbors	Number of CDP neighbors connecting to the port.
Number of sent optional TLV	Number of optional TLVs contained in an LLDP frame sent through the port.
Number of received unknown TLV	Number of unknown TLVs contained in a received LLDP frame.

display lldp tlv-config

Use display lldp tlv-config to display the types of advertisable optional LLDP TLVs of a port.

Syntax

display lldp tlv-config [ interface interface-type interface-number ] [ agent { nearest-bridge | nearest-customer | nearest-nontpmr } ]

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

interface interface-type interface-number: Specifies a port by its type and number. If you do not specify this option, the command displays the types of advertisable optional TLVs of all ports.

agent: Specifies an LLDP agent type. If you do not specify an agent type, the command displays the types of advertisable optional LLDP TLVs for all LLDP agents.

nearest-bridge: Specifies nearest bridge agents.

nearest-customer: Specifies nearest customer bridge agents.

nearest-nontpmr: Specifies nearest non-TPMR bridge agents.

Examples

# Display the types of advertisable optional LLDP TLVs of interface GigabitEthernet 1/0/1.

<Sysname> display lldp tlv-config interface gigabitethernet 1/0/1

LLDP agent nearest-bridge:

NAME STATUS DEFAULT

Basic optional TLV:

Port Description TLV YES YES

System Name TLV YES YES

System Description TLV YES YES

System Capabilities TLV YES YES

Management Address TLV YES YES

IEEE 802.1 extend TLV:

Port VLAN ID TLV YES YES

Port And Protocol VLAN ID TLV NO NO

VLAN Name TLV NO NO

DCBX TLV NO NO

EVB TLV NO NO

Link Aggregation TLV YES YES

Management VID TLV NO NO

IEEE 802.3 extend TLV:

MAC-Physic TLV YES YES

Power via MDI TLV YES YES

Maximum Frame Size TLV YES YES

LLDP-MED extend TLV:

Capabilities TLV YES YES

Network Policy TLV YES YES

Location Identification TLV NO NO

Extended Power via MDI TLV YES YES

Inventory TLV YES YES

LLDP agent nearest-nontpmr:

NAME STATUS DEFAULT

Basic optional TLV:

Port Description TLV NO NO

System Name TLV NO NO

System Description TLV NO NO

System Capabilities TLV NO NO

Management Address TLV NO NO

IEEE 802.1 extend TLV:

Port VLAN ID TLV NO NO

Port And Protocol VLAN ID TLV NO NO

VLAN Name TLV NO NO

DCBX TLV NO NO

EVB TLV YES YES

Link Aggregation TLV NO NO

Management VID TLV NO NO

IEEE 802.3 extend TLV:

MAC-Physic TLV NO NO

Power via MDI TLV NO NO

Maximum Frame Size TLV NO NO

LLDP-MED extend TLV:

Capabilities TLV NO NO

Network Policy TLV NO NO

Location Identification TLV NO NO

Extended Power via MDI TLV NO NO

Inventory TLV NO NO

LLDP agent nearest-customer:

NAME STATUS DEFAULT

Basic optional TLV:

Port Description TLV YES YES

System Name TLV YES YES

System Description TLV YES YES

System Capabilities TLV YES YES

Management Address TLV YES YES

IEEE 802.1 extend TLV:

Port VLAN ID TLV YES YES

Port And Protocol VLAN ID TLV NO NO

VLAN Name TLV NO NO

DCBX TLV NO NO

EVB TLV NO NO

Link Aggregation TLV YES YES

Management VID TLV NO NO

IEEE 802.3 extend TLV:

MAC-Physic TLV NO NO

Power via MDI TLV NO NO

Maximum Frame Size TLV NO NO

LLDP-MED extend TLV:

Capabilities TLV NO NO

Network Policy TLV NO NO

Location Identification TLV NO NO

Extended Power via MDI TLV NO NO

Inventory TLV NO NO

Table 5 Command output

Field	Description
LLDP tlv-config of port	Advertisable optional TLVs of the port.
NAME	TLV type.
STATUS	Indicates whether the type of TLV is sent through a port.
DEFAULT	Indicates whether the type of TLV is sent through a port by default.
Basic optional TLV	Basic optional TLVs: · Port Description TLV. · System Name TLV. · System Description TLV. · System Capabilities TLV. · Management Address TLV.
IEEE 802.1 extended TLV	IEEE 802.1 organizationally specific TLVs: · Port VLAN ID TLV. · Port and protocol VLAN ID TLV. · VLAN name TLV. · DCBX TLV. · EVB TLV. · Link aggregation TLV. · Management VID TLV.
IEEE 802.3 extended TLV	IEEE 802.3 organizationally specific TLVs: · MAC-Physic TLV. · Power via MDI TLV. · Maximum frame size TLV.
LLDP-MED extend TLV	LLDP-MED TLVs: · Capabilities TLV. · Network Policy TLV. · Extended Power-via-MDI TLV. · Location Identification TLV. · Inventory TLV.
Inventory TLV	Inventory TLVs: · Hardware Revision TLV. · Firmware Revision TLV. · Software Revision TLV. · Serial Number TLV. · Manufacturer Name TLV. · Model name TLV. · Asset ID TLV.

lldp admin-status

Use lldp admin-status to set the LLDP operating mode.

Use undo lldp admin-status to restore the default.

Syntax

In Layer 2, Layer 3, or management Ethernet interface view:

lldp [ agent { nearest-customer | nearest-nontpmr } ] admin-status { disable | rx | tx | txrx }

undo lldp [ agent { nearest-customer | nearest-nontpmr } ] admin-status

In Layer 2 or Layer 3 aggregate interface view:

lldp agent { nearest-customer | nearest-nontpmr } admin-status { disable | rx | tx | txrx }

undo lldp agent { nearest-customer | nearest-nontpmr } admin-status

Default

The nearest bridge agent operates in txrx mode, and the nearest customer bridge agent and nearest non-TPMR bridge agent operate in disable mode.

Views

Layer 2/Layer 3 aggregate interface view

Layer 2/Layer 3 Ethernet interface view

Management Ethernet interface view

Predefined user roles

network-admin

mdc-admin

Parameters

agent: Specifies an LLDP agent type. If you do not specify an agent type in Ethernet or management Ethernet interface view, the command sets the operating mode for nearest bridge agents.

nearest-customer: Specifies nearest customer bridge agents.

nearest-nontpmr: Specifies nearest non-TPMR bridge agents.

disable: Specifies the Disable mode. A port in this mode cannot send or receive LLDP frames.

rx: Specifies the Rx mode. A port in this mode can only receive LLDP frames.

tx: Specifies the Tx mode. A port in this mode can only send LLDP frames.

txrx: Specifies the TxRx mode. A port in this mode can send and receive LLDP frames.

Examples

# Set the LLDP operating mode to Rx for the nearest customer bridge agents on GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] lldp agent nearest-customer admin-status rx

lldp check-change-interval

Use lldp check-change-interval to enable LLDP polling and set the polling interval.

Use undo lldp check-change-interval to restore the default.

Syntax

In Layer 2, Layer 3, or management Ethernet interface view:

lldp [ agent { nearest-customer | nearest-nontpmr } ] check-change-interval interval

undo lldp [ agent { nearest-customer | nearest-nontpmr } ] check-change-interval

In Layer 2 or Layer 3 aggregate interface view:

lldp agent { nearest-customer | nearest-nontpmr } check-change-interval interval

undo lldp agent { nearest-customer | nearest-nontpmr } check-change-interval

Default

LLDP polling is disabled.

Views

Layer 2/Layer 3 aggregate interface view

Layer 2/Layer 3 Ethernet interface view

Management Ethernet interface view

Predefined user roles

network-admin

mdc-admin

Parameters

agent: Specifies an LLDP agent type. If you do not specify an agent type in Ethernet or management Ethernet interface view, the command enables LLDP polling and sets the polling interval for nearest bridge agents.

nearest-customer: Specifies nearest customer bridge agents.

nearest-nontpmr: Specifies nearest non-TPMR bridge agents.

interval: Sets the LLDP polling interval in the range of 1 to 30 seconds.

Examples

# Enable LLDP polling and set the polling interval to 30 seconds for the nearest customer bridge agents on GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] lldp agent nearest-customer check-change-interval 30

lldp compliance admin-status cdp

Use lldp compliance admin-status cdp to set the operating mode of CDP-compatible LLDP.

Use undo lldp compliance admin-status cdp to restore the default.

Syntax

lldp compliance admin-status cdp { disable | rx | txrx }

undo lldp compliance admin-status cdp

Default

CDP-compatible LLDP operates in disable mode.

Views

Layer 2 Ethernet interface view, Layer 3 Ethernet interface view, management Ethernet interface view

Predefined user roles

network-admin

mdc-admin

Parameters

disable: Specifies the disable mode. CDP-compatible LLDP in this mode cannot receive or transmit CDP packets.

rx: Specifies the Rx mode. CDP-compatible LLDP in this mode can receive but cannot send CDP packets.

txrx: Specifies the TxRx mode. CDP-compatible LLDP in this mode can send and receive CDP packets.

Usage guidelines

For your device to work with Cisco IP phones, you must perform the following tasks:

1. Enable CDP-compatible LLDP globally.

2. Configure CDP-compatible LLDP to operate in Rx or TxRx mode on the specified ports.

Examples

# Enable CDP-compatible LLDP globally and configure CDP-compatible LLDP to operate in TxRx mode on GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] lldp compliance cdp

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] lldp compliance admin-status cdp txrx

Related commands

lldp compliance cdp

Use lldp compliance cdp to enable CDP compatibility globally.

Use undo lldp compliance cdp to restore the default.

Syntax

lldp compliance cdp

undo lldp compliance cdp

Default

CDP compatibility is globally disabled.

Views

System view

Predefined user roles

network-admin

mdc-admin

Usage guidelines

The maximum TTL that CDP allows is 255 seconds. To make CDP-compatible LLDP work correctly with Cisco IP phones, set the LLDP frame transmission interval to be no more than 1/3 of the TTL value.

Examples

# Enable CDP compatibility globally.

<Sysname> system-view

[Sysname] lldp compliance cdp

Related commands

· lldp hold-multiplier

· lldp timer tx-interval

lldp enable

Use lldp enable to enable LLDP on a port.

Use undo lldp enable to disable LLDP on a port.

Syntax

lldp enable

undo lldp enable

Default

LLDP is enabled on a port.

Views

Layer 2/Layer 3 aggregate interface view

Layer 2/Layer 3 Ethernet interface view

Management Ethernet interface view

Predefined user roles

network-admin

mdc-admin

Usage guidelines

LLDP takes effect on a port only when LLDP is enabled both globally and on the port.

Examples

# Disable LLDP on GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] undo lldp enable

Related commands

lldp global enable

lldp encapsulation snap

Use lldp encapsulation snap to set the encapsulation format for LLDP frames to SNAP.

Use undo lldp encapsulation to restore the default.

Syntax

In Layer 2, Layer 3, or management Ethernet interface view:

lldp [ agent { nearest-customer | nearest-nontpmr } ] encapsulation snap

undo lldp [ agent { nearest-customer | nearest-nontpmr } ] encapsulation

In Layer 2 or Layer 3 aggregate interface view:

lldp agent { nearest-customer | nearest-nontpmr } encapsulation snap

undo lldp agent { nearest-customer | nearest-nontpmr } encapsulation

Default

The encapsulation format for LLDP frames is Ethernet II.

Views

Layer 2/Layer 3 aggregate interface view

Layer 2/Layer 3 Ethernet interface view

Management Ethernet interface view

Predefined user roles

network-admin

mdc-admin

Parameters

agent: Specifies an LLDP agent type. If you do not specify an agent type in Ethernet or management Ethernet interface view, the command sets the LLDP frame encapsulation format for nearest bridge agents.

nearest-customer: Specifies nearest customer bridge agents.

nearest-nontpmr: Specifies nearest non-TPMR bridge agents.

Usage guidelines

LLDP-CDP packets use only SNAP encapsulation.

LLDP frames carrying the EVB module TLVs cannot be encapsulated in SNAP format.

Examples

# Set the encapsulation format for LLDP frames to SNAP on GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] lldp encapsulation snap

lldp fast-count

Use lldp fast-count to set the number of LLDP frames sent each time fast LLDP frame transmission is triggered.

Use undo lldp fast-count to restore the default.

Syntax

lldp fast-count count

undo lldp fast-count

Default

The number is 4.

Views

System view

Predefined user roles

network-admin

mdc-admin

Parameters

count: Sets the number of LLDP frames sent each time fast LLDP frame transmission is triggered. The value range is 1 to 8.

Examples

# Configure the device to send five LLDP frames each time fast LLDP frame transmission is triggered.

<Sysname> system-view

[Sysname] lldp fast-count 5

lldp global enable

Use lldp global enable to enable LLDP globally.

Use undo lldp global enable to disable LLDP globally.

Syntax

lldp global enable

undo lldp global enable

Default

LLDP is disabled globally.

Views

System view

Predefined user roles

network-admin

mdc-admin

Usage guidelines

LLDP takes effect on a port only when LLDP is enabled both globally and on the port.

Examples

# Disable LLDP globally.

<Sysname> system-view

[Sysname] undo lldp global enable

Related commands

lldp enable

lldp hold-multiplier

Use lldp hold-multiplier to set the TTL multiplier.

Use undo lldp hold-multiplier to restore the default.

Syntax

lldp hold-multiplier value

undo lldp hold-multiplier

Default

The TTL multiplier is 4.

Views

System view

Predefined user roles

network-admin

mdc-admin

Parameters

value: Sets the TTL multiplier in the range of 2 to 10.

Usage guidelines

The TTL TLV carried in an LLDPDU determines how long the device information carried in the LLDPDU can be saved on a recipient device.

By setting the TTL multiplier, you can configure the TTL of locally sent LLDP frames. The TTL is expressed by using the following formula:

TTL = Min (65535, (TTL multiplier × LLDP frame transmission interval + 1))

As the expression shows, the TTL can be up to 65535 seconds.

Examples

# Set the TTL multiplier to 6.

<Sysname> system-view

[Sysname] lldp hold-multiplier 6

Related commands

lldp timer tx-interval

lldp ignore-pvid-inconsistency

Use lldp ignore-pvid-inconsistency to disable LLDP PVID inconsistency check.

Use undo lldp ignore-pvid-inconsistency to enable LLDP PVID inconsistency check.

Syntax

lldp ignore-pvid-inconsistency

undo lldp ignore-pvid-inconsistency

Default

LLDP PVID inconsistency check is enabled.

Views

System view

Default command level

network-admin

mdc-admin

Usage guidelines

By default, when the system receives an LLDP packet, it compares the PVID value contained in packet with the PVID configured on the receiving interface. If the two PVIDs do not match, a log message will be printed to notify the user.

You can disable PVID inconsistency check if different PVIDs are required on a link.

Examples

# Disable LLDP PVID inconsistency check.

<Sysname> system-view

[Sysname] lldp ignore-pvid-inconsistency

lldp management-address-format string

Use lldp management-address-format string to set the encoding format of the management address to string.

Use undo lldp management-address-format to restore the default.

Syntax

In Layer 2, Layer 3, or management Ethernet interface view:

lldp [ agent { nearest-customer | nearest-nontpmr } ] management-address-format string

undo lldp [ agent { nearest-customer | nearest-nontpmr } ] management-address-format

In Layer 2 or Layer 3 aggregate interface view:

lldp agent { nearest-customer | nearest-nontpmr } management-address-format string

undo lldp agent { nearest-customer | nearest-nontpmr } management-address-format

Default

The encoding format of the management address is numeric.

Views

Layer 2/Layer 3 aggregate interface view

Layer 2/Layer 3 Ethernet interface view

Management Ethernet interface view

Predefined user roles

network-admin

mdc-admin

Parameters

agent: Specifies an LLDP agent type. If you do not specify an agent type in Ethernet or management Ethernet interface view, the command sets the encoding format of the management address for nearest bridge agents.

nearest-bridge: Specifies nearest bridge agents.

nearest-customer: Specifies nearest customer bridge agents.

nearest-nontpmr: Specifies nearest non-TPMR bridge agents.

Usage guidelines

LLDP neighbors must use the same encoding format for the management address.

Examples

# Set the encoding format of the management address to string for the nearest customer bridge agents on GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] lldp agent nearest-customer management-address-format string

lldp max-credit

Use lldp max-credit to set the token bucket size for sending LLDP frames.

Use undo lldp max-credit to restore the default.

Syntax

lldp max-credit credit-value

undo lldp max-credit

Default

The token bucket size for sending LLDP frames is 5.

Views

System view

Predefined user roles

network-admin

mdc-admin

Parameters

credit-value: Specifies the token bucket size for sending LLDP frames, in the range of 1 to 100.

Examples

# Set the token bucket size for sending LLDP frames to 10.

<Sysname> system-view

[Sysname] lldp max-credit 10

lldp mode

Use lldp mode to configure LLDP to operate in service bridge mode.

Use undo lldp mode to restore the default.

Syntax

lldp mode service-bridge

undo lldp mode

Default

LLDP operates in customer bridge mode.

Views

System view

Predefined user roles

network-admin

mdc-admin

Parameters

service-bridge: Specifies the service bridge mode.

Usage guidelines

The LLDP agent types supported by LLDP depend on the LLDP bridge mode:

· Service bridge mode—LLDP supports nearest bridge agents and nearest non-TPMR bridge agents. LLDP processes the LLDP frames with destination MAC addresses for these agents and transparently transmits the LLDP frames with other destination MAC addresses in the VLAN.

· Customer bridge mode—LLDP supports nearest bridge agents, nearest non-TPMR bridge agents, and nearest customer bridge agents. LLDP processes the LLDP frames with destination MAC addresses for these agents and transparently transmits the LLDP frames with other destination MAC addresses in the VLAN.

The bridge mode configuration takes effect only when LLDP is enabled globally. If LLDP is disabled globally, LLDP can only operate in customer bridge mode.

Examples

# Configure LLDP to operate in service bridge mode.

<Sysname> system-view

[Sysname] lldp mode service-bridge

Related commands

lldp global enable

lldp notification med-topology-change enable

Use lldp notification med-topology-change enable to enable LLDP-MED trapping.

Use undo lldp notification med-topology-change enable to disable LLDP-MED trapping.

Syntax

lldp notification med-topology-change enable

undo lldp notification med-topology-change enable

Default

LLDP-MED trapping is disabled on ports.

Views

Layer 2 Ethernet interface view, Layer 3 Ethernet interface view, management Ethernet interface view

Predefined user roles

network-admin

mdc-admin

Examples

# Enable LLDP-MED trapping for GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] lldp notification med-topology-change enable

lldp notification remote-change enable

Use lldp notification remote-change enable to enable LLDP trapping.

Use undo lldp notification remote-change enable to disable LLDP trapping.

Syntax

In Layer 2, Layer 3, or management Ethernet interface view:

lldp [ agent { nearest-customer | nearest-nontpmr } ] notification remote-change enable

undo lldp [ agent { nearest-customer | nearest-nontpmr } ] notification remote-change enable

In Layer 2 or Layer 3 aggregate interface view:

lldp agent { nearest-customer | nearest-nontpmr } notification remote-change enable

undo lldp agent { nearest-customer | nearest-nontpmr } notification remote-change enable

Default

LLDP trapping is disabled on ports.

Views

Layer 2/Layer 3 aggregate interface view

Layer 2/Layer 3 Ethernet interface view

Management Ethernet interface view

Predefined user roles

network-admin

mdc-admin

Parameters

agent: Specifies an LLDP agent type. If you do not specify an agent type in Ethernet or management Ethernet interface view, the command enables LLDP trapping for nearest bridge agents.

nearest-customer: Specifies nearest customer bridge agents.

nearest-nontpmr: Specifies nearest non-TPMR bridge agents.

Examples

# Enable LLDP trapping for the nearest customer bridge agents on GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface GigabitEthernet 1/0/1

[Sysname-GigabitEthernet1/0/1] lldp agent nearest-customer notification remote-change enable

lldp timer fast-interval

Use lldp timer fast-interval to set an interval for fast LLDP frame transmission.

Use undo lldp timer fast-interval to restore the default.

Syntax

lldp timer fast-interval interval

undo lldp timer fast-interval

Default

The interval for fast LLDP frame transmission is 1 second.

Views

System view

Predefined user roles

network-admin

mdc-admin

Parameters

interval: Sets an interval for fast LLDP frame transmission, in the range of 1 to 3600 seconds.

Examples

# Set the interval for fast LLDP frame transmission to 2 seconds.

<Sysname> system-view

[Sysname] lldp timer fast-interval 2

lldp timer notification-interval

Use lldp timer notification-interval to set the LLDP trap and LLDP-MED trap transmission interval.

Use undo lldp timer notification-interval to restore the default.

Syntax

lldp timer notification-interval interval

undo lldp timer notification-interval

Default

The LLDP trap and LLDP-MED trap transmission interval is 30 seconds.

Views

System view

Predefined user roles

network-admin

mdc-admin

Parameters

interval: Sets the LLDP trap and LLDP-MED trap transmission interval in the range of 5 to 3600 seconds.

Examples

# Set both the LLDP trap and LLDP-MED trap transmission interval to 8 seconds.

<Sysname> system-view

[Sysname] lldp timer notification-interval 8

lldp timer reinit-delay

Use lldp timer reinit-delay to set the LLDP reinitialization delay.

Use undo lldp timer reinit-delay to restore the default.

Syntax

lldp timer reinit-delay delay

undo lldp timer reinit-delay

Default

The LLDP reinitialization delay is 2 seconds.

Views

System view

Predefined user roles

network-admin

mdc-admin

Parameters

delay: Sets the LLDP reinitialization delay in the range of 1 to 10 seconds.

Examples

# Set the LLDP reinitialization delay to 4 seconds.

<Sysname> system-view

[Sysname] lldp timer reinit-delay 4

lldp timer tx-interval

Use lldp timer tx-interval to set the LLDP frame transmission interval.

Use undo lldp timer tx-interval to restore the default.

Syntax

lldp timer tx-interval interval

undo lldp timer tx-interval

Default

The LLDP frame transmission interval is 30 seconds.

Views

System view

Predefined user roles

network-admin

mdc-admin

Parameters

interval: Sets the LLDP frame transmission interval in the range of 5 to 32768 seconds.

Examples

# Set the LLDP frame transmission interval to 20 seconds.

<Sysname> system-view

[Sysname] lldp timer tx-interval 20

lldp tlv-enable

Use lldp tlv-enable to configure the types of advertisable TLVs.

Use undo lldp tlv-enable to disable the advertising of the specified types of TLVs.

Syntax

In Layer 2 Ethernet interface view:

· For nearest bridge agents:

lldp tlv-enable { basic-tlv { all | port-description | system-capability | system-description | system-name | management-address-tlv [ ip-address ] } | dot1-tlv { all | port-vlan-id | link-aggregation | dcbx | protocol-vlan-id [ vlan-id ] | vlan-name [ vlan-id ] | management-vid [ mvlan-id ] } | dot3-tlv { all | mac-physic | max-frame-size | power } | med-tlv { all | capability | inventory | network-policy [ vlan-id ] | power-over-ethernet | location-id { civic-address device-type country-code { ca-type ca-value }&<1-10> | elin-address tel-number } } }

undo lldp tlv-enable { basic-tlv { all | port-description | system-capability | system-description | system-name | management-address-tlv [ ip-address ] } | dot1-tlv { all | port-vlan-id | link-aggregation | dcbx | protocol-vlan-id | vlan-name | management-vid } | dot3-tlv { all | mac-physic | max-frame-size | power } | med-tlv { all | capability | inventory | network-policy [ vlan-id ] | power-over-ethernet | location-id } }

· For nearest non-TPMR bridge agents:

lldp agent nearest-nontpmr tlv-enable { basic-tlv { all | port-description | system-capability | system-description | system-name | management-address-tlv [ ip-address ] } | dot1-tlv { all | evb | port-vlan-id | link-aggregation } }

undo lldp agent nearest-nontpmr tlv-enable { basic-tlv { all | port-description | system-capability | system-description | system-name | management-address-tlv [ ip-address ] } | dot1-tlv { all | evb | port-vlan-id | link-aggregation } }

· For nearest customer bridge agents:

lldp agent nearest-customer tlv-enable { basic-tlv { all | port-description | system-capability | system-description | system-name | management-address-tlv [ ip-address ] } | dot1-tlv { all | port-vlan-id | link-aggregation } }

undo lldp agent nearest-customer tlv-enable { basic-tlv { all | port-description | system-capability | system-description | system-name | management-address-tlv [ ip-address ] } | dot1-tlv { all | port-vlan-id | link-aggregation } }

In Layer 3 or management Ethernet interface view:

· lldp tlv-enable { basic-tlv { all | port-description | system-capability | system-description | system-name | management-address-tlv [ ip-address ] } | dot1-tlv { all | link-aggregation } | dot3-tlv { all | mac-physic | max-frame-size | power } | med-tlv { all | capability | inventory | power-over-ethernet | location-id { civic-address device-type country-code { ca-type ca-value }&<1-10> | elin-address tel-number } } }

· lldp agent { nearest-nontpmr | nearest-customer } tlv-enable { basic-tlv { all | port-description | system-capability | system-description | system-name | management-address-tlv [ ip-address ] } | dot1-tlv { all | link-aggregation } }

· undo lldp tlv-enable { basic-tlv { all | port-description | system-capability | system-description | system-name | management-address-tlv [ ip-address ] } | dot1-tlv { all | link-aggregation } | dot3-tlv { all | mac-physic | max-frame-size | power } | med-tlv { all | capability | inventory | power-over-ethernet | location-id } }

· undo lldp agent { nearest-nontpmr | nearest-customer } tlv-enable { basic-tlv { all | port-description | system-capability | system-description | system-name | management-address-tlv [ ip-address ] } | dot1-tlv { all | link-aggregation } }

In Layer 2 aggregate interface view:

· lldp agent nearest-nontpmr tlv-enable { basic-tlv { all | management-address-tlv [ ip-address ] | port-description | system-capability | system-description | system-name } | dot1-tlv { all | evb | port-vlan-id } }

· lldp agent nearest-customer tlv-enable { basic-tlv { all | management-address-tlv [ ip-address ] | port-description | system-capability | system-description | system-name } | dot1-tlv { all | port-vlan-id } }

· lldp tlv-enable dot1-tlv { protocol-vlan-id [ vlan-id ] | vlan-name [ vlan-id ] | management-vid [ mvlan-id ] }

· undo lldp agent nearest-nontpmr tlv-enable { basic-tlv { all | management-address-tlv [ ip-address ] | port-description | system-capability | system-description | system-name } | dot1-tlv { all | evb | port-vlan-id } }

· undo lldp agent nearest-customer tlv-enable { basic-tlv { all | management-address-tlv [ ip-address ] | port-description | system-capability | system-description | system-name } | dot1-tlv { all | port-vlan-id } }

· undo lldp tlv-enable dot1-tlv { protocol-vlan-id | vlan-name | management-vid }

In Layer 3 aggregate interface view:

· lldp agent { nearest-nontpmr | nearest-customer } tlv-enable basic-tlv { all | management-address-tlv [ ip-address ] | port-description | system-capability | system-description | system-name }

· undo lldp agent { nearest-nontpmr | nearest-customer } tlv-enable basic-tlv { all | management-address-tlv [ ip-address ] | port-description | system-capability | system-description | system-name }

Default

On Layer 2 Ethernet interfaces:

· Nearest bridge agents can advertise all types of LLDP TLVs (only port VLAN ID and link aggregation TLVs are supported in 802.1 organizationally specific TLVs) except the location identification TLV. Nearest non-TPMR bridge agents can advertise only EVB TLVs.

· Nearest customer bridge agents can advertise basic TLVs and IEEE 802.1 organizationally specific TLVs (only port VLAN ID and link aggregation TLVs are supported).

On Layer 3 or management Ethernet interfaces:

· Nearest bridge agents can advertise all types of LLDP TLVs (only link aggregation TLV is supported in 802.1 organizationally specific TLVs) except network policy and location identification TLVs.

· Nearest non-TPMR bridge agents advertise no TLVs.

· Nearest customer bridge agents can advertise basic TLVs and IEEE 802.1 organizationally specific TLVs (only link aggregation TLV is supported).

On Layer 2 aggregate interfaces:

· Nearest non-TPMR bridge agents can advertise only EVB TLVs.

· Nearest customer bridge agents can advertise basic TLVs and IEEE 802.1 organizationally specific TLVs. Among the IEEE 802.1 organizationally specific TLVs, only port and protocol VLAN ID TLV is supported.

On Layer 3 aggregate interfaces:

· Nearest non-TPMR bridge agents advertise no TLVs.

· Nearest customer bridge agents can advertise only basic TLVs.

Views

Layer 2/Layer 3 aggregate interface view

Layer 2/Layer 3 Ethernet interface view

Management Ethernet interface view

Predefined user roles

network-admin

mdc-admin

Parameters

agent: Specifies an LLDP agent type. If you do not specify an agent type in Ethernet or management Ethernet interface view, the command configures the types of advertisable TLVs for nearest bridge agents.

nearest-customer: Specifies nearest customer bridge agents.

nearest-nontpmr: Specifies nearest non-TPMR bridge agents.

all: Advertises all TLVs of the specified type.

· Enables the interface to advertise the following TLVs:

¡ All basic LLDP TLVs if the all keyword is specified for basic-tlv.

¡ All IEEE 802.1 organizationally specific LLDP TLVs if the all keyword is specified for dot1-tlv.

¡ All IEEE 802.3 organizationally specific LLDP TLVs if the all keyword is specified for dot3-tlv.

· Enables the interface to advertise all LLDP-MED TLVs except location identification TLVs if the all keyword is specified for med-tlv.

basic-tlv: Advertises basic LLDP TLVs.

management-address-tlv [ ip-address ]: Advertises management address TLVs. ip-address specifies the management address to be advertised. By default, the following rules apply:

· For a Layer 2 Ethernet or aggregate interface, the management address is the primary IP address of the VLAN interface meeting the following requirements:

¡ In up state.

¡ The corresponding VLAN ID is the lowest among the VLANs permitted on the port.

If none of the VLAN interfaces of the permitted VLANs is assigned an IP address or all VLAN interfaces are down, the MAC address of the port will be advertised.

· For a Layer 3 Ethernet or aggregate interface, or a management Ethernet interface, the management address is the IP address of the interface. If no IP address is configured for the Layer 3 Ethernet or aggregate interface, the MAC address of the port will be advertised.

port-description: Advertises port description TLVs.

system-capability: Advertises system capabilities TLVs.

system-description: Advertises system description TLVs.

system-name: Advertises system name TLVs.

dot1-tlv: Advertises IEEE 802.1 organizationally specific LLDP TLVs.

dcbx: Advertises the DCBX TLV.

evb: Advertises the EVB module TLVs.

port-vlan-id: Advertises port VLAN ID TLVs.

protocol-vlan-id [ vlan-id ]: Advertises port and protocol VLAN ID TLVs. The vlan-id argument specifies a VLAN ID in the TLVs to be advertised. The VLAN ID is in the range of 1 to 4094, and the default is the lowest VLAN ID on the port.

vlan-name [ vlan-id ]: Advertises VLAN name TLVs. The vlan-id argument specifies a VLAN ID in the TLVs to be advertised. The VLAN ID is in the range of 1 to 4094, and the default is the lowest VLAN ID on the port.

management-vid [ mvlan-id ]: Advertises management VLAN ID TLVs. The mvlan-id argument specifies a management VLAN ID in the TLVs to be advertised. The management VLAN ID is in the range of 1 to 4094. If you do not specify this option, the value 0 is advertised, which means that the LLDP agent is not configured with a management VLAN ID.

dot3-tlv: Advertises IEEE 802.3 organizationally specific LLDP TLVs.

link-aggregation: Advertises link aggregation TLVs.

mac-physic: Advertises MAC/PHY configuration/status TLVs.

max-frame-size: Advertises maximum frame size TLVs.

power: Advertises power in MDI TLVs and power stateful control TLVs.

med-tlv: Advertises LLDP-MED TLVs.

capability: Advertises LLDP-MED capabilities TLVs.

inventory: Advertises the following TLVs: hardware revision, firmware revision, software revision, serial number, manufacturer name, model name, and asset ID.

location-id: Advertises location identification TLVs.

civic-address: Inserts the typical address information about the network device in location identification TLVs.

device-type: Sets a device type value in the range of 0 to 2:

· Value 0 specifies a DHCP server.

· Value 1 specifies a switch.

· Value 2 specifies an LLDP-MED endpoint.

country-code: Sets a country code defined in ISO 3166.

{ ca-type ca-value }&<1-10>: Configures address information. ca-type represents the address information type in the range of 0 to 255. ca-value represents address information, a string of 1 to 250 characters. &<1-10> indicates that you can specify up to 10 ca-type ca-value pairs.

elin-address: Inserts telephone numbers for emergencies in location identification TLVs.

tel-number: Sets the telephone number for emergencies, a string of 10 to 25 characters.

network-policy [ vlan-id ]: Advertises network policy TLVs. vlan-id specifies the voice VLAN ID to be advertised, in the range of 1 to 4094.

power-over-ethernet: Advertises extended power-via-MDI TLVs.

Usage guidelines

Nearest bridge agents are not supported on aggregate interfaces.

You can enable the device to advertise multiple types of TLVs by using this command without the all keyword specified.

If the MAC/PHY configuration/status TLV is not advertisable, none of the LLDP-MED TLVs will be advertised whether or not they are advertisable. If the LLDP-MED capabilities TLV is not advertisable, the other LLDP-MED TLVs will not be advertised regardless of whether or not they are advertisable.

The port and protocol VLAN ID, VLAN name, and management VLAN ID TLVs in IEEE 802.1 organizationally specific LLDP TLVs can be configured only for nearest bridge agents. The configuration can be inherited by nearest customer bridge agents and nearest non-TPMR bridge agents.

Examples

# Enable the nearest customer bridge agents on GigabitEthernet 1/0/1 to advertise link aggregation TLVs of the IEEE 802.1 organizationally specific TLVs.

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] lldp agent nearest-customer tlv-enable dot1-tlv link-aggregation

04-Layer 2 - LAN Switching Command Reference

LLDP commands

Intelligent Terminal Products

Product Support Services

Technical Service Solutions

Resource Center

Policy

Online Help

Become a Partner

Partner Policy & Program

Global Learning

Partner Sales Resources

Service Business

News & Events

Contact Us