Login
- Released At: 18-11-2019
- Page Views:
- Downloads:
- Table of Contents
- Related Documents
-
24-port 10/100/1000BASE-T electrical Ethernet interface + 20-port 1000BASE-X-SFP + 4-port 10GBASE-R-SFP+ optical Ethernet interface card—LSQM2GT24PTSSC0
1 Card identifier
The card identifier LSQM2GT24PTSSC0 is in the upper right corner of the front panel.
2 Specifications
|
|
IMPORTANT: Before installing the card, you must remove the protection cover from the card to ensure correct installation. |
Table 1 Card specifications
|
Item |
Specifications |
|
Card size (H × W × D) |
40 × 399 × 355 mm (1.57 × 15.71 × 13.98 in) |
|
SDRAM (DDR3) |
1GB |
|
Power consumption |
36 W to 59 W |
|
Ports |
· 24 x 10/100/1000BASE-T copper ports · 20 × 1000BASE-X-SFP fiber ports · 4 x 10GBASE-R-SFP+ fiber ports |
|
Connector type |
· RJ-45. · LC. |
|
Port speed |
· 10/100/1000BASE-T copper port: 10/100/1000 Mbps · 1000BASE-X-SFP fiber port: 1000 Mbps · 10GBASE-R-SFP+ fiber port: 10 Gbps |
|
Transmission medium and max transmission distance |
· 10/100/1000BASE-T copper port: 100 m (328.08 ft) over Category 5 or higher twisted pair cables · 1000BASE-X-SFP fiber port: see Table 3 · 10GBASE-R-SFP+ fiber port: see Table 3 , Table 4 and Table 5 |
|
Applicable hardware platforms |
· All S7500E models · All S7500X models |
|
Applicable host software versions |
Release 7150 and Later |
The 10/100/1000BASE-T copper port uses an RJ-45 connector.
Figure 1 RJ-45 connector
Table 2 RJ-45 GE connector pinout
|
Pin |
10BASE-T/100BASE-TX/1000BASE-T |
|
|
Signal |
Function |
|
|
1 |
MX_0+ |
Transmits and receives data. |
|
2 |
MX_0- |
Transmits and receives data. |
|
3 |
MX_1+ |
Transmits and receives data. |
|
4 |
MX_2+ |
Transmits and receives data. |
|
5 |
MX_2- |
Transmits and receives data. |
|
6 |
MX_1- |
Transmits and receives data. |
|
7 |
MX_3+ |
Transmits and receives data. |
|
8 |
MX_3- |
Transmits and receives data. |
Table 3 describes the SFP transceiver modules available for the card.
Table 3 SFP transceiver module specifications
|
Module |
Central wavelength |
Connector type |
Cable specifications |
Maximum transmission distance |
|
850 nm |
LC |
50/125 μm multi-mode optical fiber |
550 m (0.34 miles) |
|
|
850 nm |
LC |
62.5/125 μm multi-mode optical fiber |
275 m (0.17 miles) |
|
|
SFP-GE-SX-MM850-D |
850 nm |
LC |
50/125 μm multi-mode optical fiber |
550 m (0.34 miles) |
|
850 nm |
LC |
62.5/125 μm multi-mode optical fiber |
275 m (0.17 miles) |
|
|
SFP-GE-LX-SM1310-A |
1310 nm |
LC |
9/125 μm single-mode optical fiber |
10 km (6.21 miles) |
|
1310 nm |
LC |
50/125 μm multi-mode optical fiber |
550 m (1804.46 ft) |
|
|
1310 nm |
LC |
62.5/125 μm multi-mode optical fiber |
550 m (1804.46 ft) |
|
|
SFP-GE-LX-SM1310-D |
1310 nm |
LC |
9/125 μm single-mode optical fiber |
10 km (6.21 miles) |
|
1310 nm |
LC |
50/125 μm multi-mode optical fiber |
550 m (1804.46 ft) |
|
|
1310 nm |
LC |
62.5/125 μm multi-mode optical fiber |
550 m (1804.46 ft) |
|
|
SFP-GE-LH40-SM1310 |
1310 nm |
LC |
9/125 μm single-mode optical fiber |
40 km (24.86 miles) |
|
SFP-GE-LH40-SM1310-BIDI |
RX: 1550 nm TX: 1310 nm |
LC |
9/125 μm single-mode optical fiber |
40 km (24.86 miles) |
|
SFP-GE-LH40-SM1310-D |
1310nm |
LC |
9/125 μm single-mode optical fiber |
40 km (24.86 miles) |
|
SFP-GE-LH40-SM1550 |
1550 nm |
LC |
9/125 μm single-mode optical fiber |
40 km (24.86 miles) |
|
SFP-GE-LH40-SM1550-BIDI |
RX: 1310 nm TX: 1550 nm |
LC |
9/125 μm single-mode optical fiber |
40 km (24.86 miles) |
|
SFP-GE-LH80-SM1550 |
1550 nm |
LC |
9/125 μm single-mode optical fiber |
80 km (49.71 miles) |
|
SFP-GE-LH80-SM1550-D |
1550 nm |
LC |
9/125 μm single-mode optical fiber |
80 km (49.71 miles) |
|
SFP-GE-LH100-SM1550 |
1550 nm |
LC |
9/125 μm single-mode optical fiber |
100 km (62.14 miles) |
|
SFP-GE-LX-SM1310-BIDI |
RX: 1490 nm TX: 1310 nm |
LC |
9/125 μm single-mode optical fiber |
10 km (6.21 miles) |
|
SFP-GE-LX-SM1490-BIDI |
RX: 1310 nm TX: 1490 nm |
LC |
9/125 μm single-mode optical fiber |
10 km (6.21 miles) |
|
SFP-GE-T |
N/A |
RJ-45 |
Category-5 twisted pair cable |
100 m (0.06 miles) |
|
SFP-GE-T-D |
N/A |
RJ-45 |
Category-5 twisted pair cable |
100 m (0.06 miles) |
|
SFP-FE-SX-MM1310-A |
1310 nm |
LC |
50/125 μm multi-mode optical fiber |
2 km (1.24 miles) |
|
62.5/125 μm multi-mode optical fiber |
275 m (0.17 miles) |
|||
|
SFP-FE-LX-SM1310-A |
1310 nm |
LC |
9/125 μm single-mode optical fiber |
15 km (9.32 miles) |
|
SFP-FE-LX-SM1310-D |
1310 nm |
LC |
9/125 μm single-mode optical fiber |
15 km (9.32 miles) |
|
|
NOTE: · BIDI modules use different central wavelengths in transmit and receive directions, in order to implement bidirectional transmission of optical signals over the same fiber. · BIDI modules must be used in pairs. For example, if an SFP-GE-LX-SM1310-BIDI is used at one end, an SFP-GE-LX-SM1490-BIDI must be used at the other end. · The 10GBASE-R-SFP+ port does not support the following SFP transceiver modules: SFP-GE-T, SFP-GE-T-D, SFP-FE-SX-MM1310-A, SFP-FE-LX-SM1310-A, and SFP-FE-LX-SM1310-D. |
Table 4 describes the SFP+ transceiver modules available for the SFP+ ports on the card.
Table 4 SFP+ transceiver module specifications
|
Module |
Central wavelength |
Connector type |
Cable specifications |
Maximum transmission distance |
|
SFP-XG-SX-MM850-A |
850 nm |
LC |
50/125 μm multi-mode optical fiber |
300 m (984.25 ft) |
|
850 nm |
LC |
62.5/125 μm multi-mode optical fiber |
33 m (108.27 ft) |
|
|
SFP-XG-SX-MM850-D |
850 nm |
LC |
50/125 μm multi-mode optical fiber |
300 m (984.25 ft) |
|
850 nm |
LC |
62.5/125 μm multi-mode optical fiber |
33 m (108.27 ft) |
|
|
SFP-XG-SX-MM850-E |
850 nm |
LC |
50/125 μm multi-mode optical fiber |
300 m (984.25 ft) |
|
850 nm |
LC |
62.5/125 μm multi-mode optical fiber |
33 m (108.27 ft) |
|
|
SFP-XG-SX-MM850-F1 |
850 nm |
LC |
50/125 μm multi-mode optical fiber |
300 m (984.25 ft) |
|
850 nm |
LC |
62.5/125 μm multi-mode optical fiber |
33 m (108.27 ft) |
|
|
SFP-XG-LX-SM1310 |
1310 nm |
LC |
9/125 μm single-mode optical fiber |
10 km (6.21 miles) |
|
SFP-XG-LX-SM1310-D |
1310 nm |
LC |
9/125 μm single-mode optical fiber |
10 km (6.21 miles) |
|
SFP-XG-LX-SM1310-E |
1310 nm |
LC |
9/125 μm single-mode optical fiber |
10 km (6.21 miles) |
|
SFP-XG-LH40-SM1550 |
1550nm |
LC |
9/125 μm single-mode optical fiber |
40 km (24.86 miles) |
|
SFP-XG-LH40-SM1550-D |
1550nm |
LC |
9/125 μm single-mode optical fiber |
40 km (24.86 miles) |
|
SFP-XG-LH80-SM1550 |
1550nm |
LC |
9/125 μm single-mode optical fiber |
80 km (49.71 miles) |
|
SFP-XG-LH80-SM1550-D |
1550nm |
LC |
9/125 μm single-mode optical fiber |
80 km (49.71 miles) |
Table 5 describes the SFP+ DAC cables available for the SFP+ ports on the card.
Table 5 SFP+ DAC cable specifications
|
SFP+ DAC cable |
Cable length |
Data rate |
Cable type |
Remark |
|
LSWM1STK |
0.65 m (2.13 ft) |
10.31 Gbps |
SFP+ cable |
Use for connecting SFP+ ports |
|
LSWM2STK |
1.2 m (3.94 ft) |
|||
|
LSWM3STK |
3 m (9.84 ft) |
3 Related documentation
For module installation, see H3C S7500E Switch Series Installation Guide and H3C S7500X Switch Series Installation Guide.
For software upgrade, see the release notes for the device.
Copyright © 2014-2018 New H3C Technologies Co ., Ltd.
The information in this document is subject to change without notice.
