Login
- Released At: 18-11-2019
- Page Views:
- Downloads:
- Table of Contents
- Related Documents
-
48-port 1000BASE-X-SFP optical Ethernet interface card—LSQM2GP48SA0
1 Card identifier
The card identifier LSQM2GP48SA0 is in the upper right corner of the front panel.
2 Specifications
|
|
IMPORTANT: Before installing the card, you must remove the protection cover from the card to ensure correct installation. |
Table 1 Card specifications
|
Item |
Specifications |
|
Card size (H × W × D) |
40 × 399 × 355 mm (1.57 × 15.71 × 13.98 in) |
|
SDRAM (DDR3) |
1GB |
|
Power consumption |
28 W to 58 W |
|
Ports |
48 x 1000BASE-X-SFP fiber ports |
|
Connector type |
LC |
|
Port rate |
1000 Mbps |
|
Transmission medium and max transmission distance |
|
|
Applicable hardware platforms |
· All S7500E models · All S7500X models |
|
System software version |
Release 7178 and Later |
Table 2 describes the SFP transceiver modules available for the card.
Table 2 SFP transceiver module specifications
|
Module |
Central wavelength |
Connector type |
Cable specifications |
Maximum transmission distance |
|
SFP-GE-SX-MM850-A |
850 nm |
LC |
50/125 μm multi-mode optical fiber |
550 m (0.34 miles) |
|
850 nm |
LC |
62.5/125 μm multi-mode optical fiber |
275 m (0.17 miles) |
|
|
SFP-GE-SX-MM850-D |
850 nm |
LC |
50/125 μm multi-mode optical fiber |
550 m (0.34 miles) |
|
850 nm |
LC |
62.5/125 μm multi-mode optical fiber |
275 m (0.17 miles) |
|
|
SFP-GE-LX-SM1310-A |
1310 nm |
LC |
9/125 μm single-mode optical fiber |
10 km (6.21 miles) |
|
1310 nm |
LC |
50/125 μm multi-mode optical fiber |
550 m (1804.46 ft) |
|
|
1310 nm |
LC |
62.5/125 μm multi-mode optical fiber |
550 m (1804.46 ft) |
|
|
SFP-GE-LX-SM1310-D |
1310 nm |
LC |
9/125 μm single-mode optical fiber |
10 km (6.21 miles) |
|
1310 nm |
LC |
50/125 μm multi-mode optical fiber |
550 m (1804.46 ft) |
|
|
1310 nm |
LC |
62.5/125 μm multi-mode optical fiber |
550 m (1804.46 ft) |
|
|
SFP-GE-LH40-SM1310 |
1310 nm |
LC |
9/125 μm single-mode optical fiber |
40 km (24.86 miles) |
|
SFP-GE-LH40-SM1310-D |
1310nm |
LC |
9/125 μm single-mode optical fiber |
40 km (24.86 miles) |
|
SFP-GE-LH40-SM1550 |
1550 nm |
LC |
9/125 μm single-mode optical fiber |
40 km (24.86 miles) |
|
SFP-GE-LH80-SM1550 |
1550 nm |
LC |
9/125 μm single-mode optical fiber |
70 km (43.50 miles) |
|
SFP-GE-LH80-SM1550-D |
1550nm |
LC |
9/125 μm single-mode optical fiber |
70 km (43.50 miles) |
|
SFP-GE-LH100-SM1550 |
1550 nm |
LC |
9/125 μm single-mode optical fiber |
100 km (62.14 miles) |
|
SFP-GE-LX-SM1310-BIDI |
RX: 1490 nm TX: 1310 nm |
LC |
9/125 μm single-mode optical fiber |
10 km (6.21 miles) |
|
SFP-GE-LX-SM1490-BIDI |
RX: 1310 nm TX: 1490 nm |
LC |
9/125 μm single-mode optical fiber |
10 km (6.21 miles) |
|
SFP-GE-T |
N/A |
RJ-45 |
Category-5 twisted pair cable |
100 m (0.06 miles) |
|
SFP-GE-T-D |
N/A |
RJ-45 |
Category-5 twisted pair cable |
100 m (0.06 miles) |
|
SFP-FE-SX-MM1310-A |
1310 nm |
LC |
50/125 μm multi-mode optical fiber |
2 km (1.24 miles) |
|
62.5/125 μm multi-mode optical fiber |
275 m (0.17 miles) |
|||
|
SFP-FE-LX-SM1310-A |
1310 nm |
LC |
9/125 μm single-mode optical fiber |
15 km (9.32 miles) |
|
SFP-FE-LX-SM1310-D |
1310 nm |
LC |
9/125 μm single-mode optical fiber |
15 km (9.32 miles) |
|
|
NOTE: · BIDI modules use different central wavelengths in transmit and receive directions, in order to implement bidirectional transmission of optical signals over the same fiber. · BIDI modules must be used in pairs. For example, if an SFP-GE-LX-SM1310-BIDI is used at one end, an SFP-GE-LX-SM1490-BIDI must be used at the other end. |
3 Related documentation
For module installation, see H3C S7500E Switch Series Installation Guide and H3C S7500X Switch Series Installation Guide.
For software upgrade, see the release notes for the device.
Copyright © 2015-2018 New H3C Technologies Co., Ltd.
The information in this document is subject to change without notice.
