- Released At: 18-11-2019
- Page Views:
- Downloads:
- Table of Contents
- Related Documents
-
1 Card identifier
The card identifier LSQM1CTGS24QSFD0 is in the upper right corner of the front panel
2 Specifications
|
IMPORTANT: H3C recommends that you use only H3C-certified USB disks to ensure hardware reliability and compatibility. |
Table 1 Card specifications
Item |
Specification |
Flash |
2 GB |
BootROM |
8 MB |
NVRAM |
1 MB |
SDRAM (DDR3) |
2 GB |
Card size (H × W × D) |
40 × 399 × 355 mm (1.57 × 15.71 × 13.98 in) |
Power consumption |
60 W to 110W |
Interfaces |
· 1 console port · 1 USB console port · 2 network management ports: 1 RJ-45 ports and 1 SFP fiber ports · 24 x 10GBASE-R-SFP+ fiber port · 2 × 40GGBASE-R-QSFP+ fiber port or 1 × 100GBASE-R-QSFP28 fiber port · 1 primary USB port |
Transmission rate |
· Console port: 9600 bps to 115200 bps (default: 9600 bps) · USB console port: ≤ 115200 bps (default: 9600 bps) · network management ports ( RJ-45 ): 10/100/1000 Mbps, half/full duplex · network management ports (SFP ): 1000 Mbps · 10GBASE-R-SFP+ fiber port :1Gbps/10 Gbps · 40GGBASE-R-QSFP+ fiber port: 40 Gbps · 100GBASE-R-QSFP28 fiber port: 100 Gbps |
Transmission medium and max transmission distance |
· Console port: 15 m (49.21 ft) over asynchronous EIA/TIA-232 cables · USB console port: 10 m (32.81 ft) over USB-AB cables · network management ports ( RJ-45 ): 100 m (328.08 ft) over Category 5 or higher twisted pair cables · network management ports (SFP ): see Table 3 · 10GBASE-R-SFP+ fiber port: see Table 3,Table 4 and Table 5 · 40GBASE-R-QSFP+ fiber port: see Table 6,Table 7, Table 8 and Table 9 · 100GBASE-R-QSFP28 fiber port: see Table 10 |
Compatible device models |
S7503E-M |
Software version |
Version R7556 and later |
|
NOTE: · H3C recommends not using a USB extender cable to connect the USB port. · After you change 40-GE interfaces to 100-GE interfaces, only port 25 is available. |
The 10/100/1000BASE-T copper port uses an RJ-45 connector.
Figure 1 RJ-45 connector
Table 2 RJ-45 GE connector pinout
Pin |
10BASE-T/100BASE-TX/1000BASE-T |
|
Signal |
Function |
|
1 |
MX_0+ |
Transmits and receives data. |
2 |
MX_0- |
Transmits and receives data. |
3 |
MX_1+ |
Transmits and receives data. |
4 |
MX_2+ |
Transmits and receives data. |
5 |
MX_2- |
Transmits and receives data. |
6 |
MX_1- |
Transmits and receives data. |
7 |
MX_3+ |
Transmits and receives data. |
8 |
MX_3- |
Transmits and receives data. |
Table 3 describes the SFP transceiver modules available for the SFP and SFP+ ports on the card.
Table 3 GE SFP transceiver modules available for the SFP and SFP+ ports
GE SFP transceiver module |
Central wavelength |
Connector type |
Cable specifications |
Maximum transmission distance |
SFP-GE-T |
N/A |
RJ-45 |
Category-5 twisted pair cable |
100 m (0.06 miles) |
SFP-GE-T-D |
N/A |
RJ-45 |
Category-5 twisted pair cable |
100 m (0.06 miles) |
SFP-GE-SX-MM850-A |
850 nm |
LC |
50/125 μm multi-mode optical fiber (MMF) |
550 m (0.34 miles) |
62.5/125 μm MMF |
275 m (0.17 miles) |
|||
SFP-GE-SX-MM850-D |
850 nm |
LC |
50/125 μm MMF |
550 m (0.34 miles) |
62.5/125 μm MMF |
275 m (0.17 miles) |
|||
SFP-GE-LX-SM1310-A |
1310 nm |
LC |
9/125 μm single-mode optical fiber (SMF) |
10 km (6.21 miles) |
50/125 μm MMF |
550 m (1804.46 ft) |
|||
62.5/125 μm MMF |
550 m (1804.46 ft) |
|||
SFP-GE-LX-SM1310-D |
1310 nm |
LC |
9/125 μm SMF |
10 km (6.21 miles) |
50/125 μm MMF |
550 m (1804.46 ft) |
|||
62.5/125 μm MMF |
550 m (1804.46 ft) |
|||
SFP-GE-LH40-SM1310 |
1310 nm |
LC |
9/125 μm SMF |
40 km (24.86 miles) |
SFP-GE-LH40-SM1310-D |
1310 nm |
LC |
9/125 μm SMF |
40 km (24.86 miles) |
SFP-GE-LH40-SM1550 |
1550 nm |
LC |
9/125 μm SMF |
40 km (24.86 miles) |
SFP-GE-LH70-SM1550 |
1550 nm |
LC |
9/125 μm SMF |
80 km (49.71 miles) |
SFP-GE-LH70-SM1550-D |
1550nm |
LC |
9/125 μm SMF |
80 km (49.71 miles) |
SFP-GE-LH100-SM1550 |
1550 nm |
LC |
9/125 μm SMF |
100 km (62.14 miles) |
SFP-GE-LX-SM1310-BIDI |
RX: 1490 nm TX: 1310 nm |
LC |
9/125 μm SMF |
10 km (6.21 miles) |
SFP-GE-LX-SM1490-BIDI |
RX: 1310 nm TX: 1490 nm |
LC |
9/125 μm SMF |
10 km (6.21 miles) |
|
NOTE: · BIDI modules use different central wavelengths in transmit and receive directions, in order to implement bidirectional transmission of optical signals over the same fiber. · The BIDI modules must be used in pairs. For example, if you install the SFP-GE-LX-SM1310-BIDI in the local port, you must install the SFP-GE-LX-SM1490-BIDI in the peer port. |
Table 4 describes the SFP+ transceiver modules available for the SFP+ ports on the card.
Table 4 SFP+ transceiver module specifications
Module |
Central wavelength |
Connector type |
Cable specifications |
Maximum transmission distance |
SFP-XG-SX-MM850-A |
850 nm |
LC |
50/125 μm multi-mode optical fiber |
300 m (984.25 ft) |
850 nm |
LC |
62.5/125 μm multi-mode optical fiber |
33 m (108.27 ft) |
|
SFP-XG-SX-MM850-D |
850 nm |
LC |
50/125 μm multi-mode optical fiber |
300 m (984.25 ft) |
850 nm |
LC |
62.5/125 μm multi-mode optical fiber |
33 m (108.27 ft) |
|
SFP-XG-SX-MM850-E |
850 nm |
LC |
50/125 μm multi-mode optical fiber |
300 m (984.25 ft) |
850 nm |
LC |
62.5/125 μm multi-mode optical fiber |
33 m (108.27 ft) |
|
SFP-XG-SX-MM850-F1 |
850 nm |
LC |
50/125 μm multi-mode optical fiber |
300 m (984.25 ft) |
850 nm |
LC |
62.5/125 μm multi-mode optical fiber |
33 m (108.27 ft) |
|
SFP-XG-LX-SM1310 |
1310 nm |
LC |
9/125 μm single-mode optical fiber |
10 km (6.21 miles) |
SFP-XG-LX-SM1310-D |
1310 nm |
LC |
9/125 μm single-mode optical fiber |
10 km (6.21 miles) |
SFP-XG-LX-SM1310-E |
1310 nm |
LC |
9/125 μm single-mode optical fiber |
10 km (6.21 miles) |
SFP-XG-LH40-SM1550 |
1550nm |
LC |
9/125 μm single-mode optical fiber |
40 km (24.86 miles) |
SFP-XG-LH40-SM1550-D |
1550nm |
LC |
9/125 μm single-mode optical fiber |
40 km (24.86 miles) |
SFP-XG-LH80-SM1550 |
1550nm |
LC |
9/125 μm single-mode optical fiber |
80 km (49.71 miles) |
SFP-XG-LH80-SM1550-D |
1550nm |
LC |
9/125 μm single-mode optical fiber |
80 km (49.71 miles) |
Table 5 describes the SFP+ DAC cables available for the SFP+ ports on the card.
Table 5 SFP+ DAC cable specifications
SFP+ DAC cable |
Cable length |
Data rate |
Cable type |
Remark |
LSWM1STK |
0.65 m (2.13 ft) |
10 Gbps |
SFP+ cable |
Use for connecting SFP+ ports |
LSWM2STK |
1.2 m (3.94 ft) |
|||
LSWM3STK |
3 m (9.84 ft) |
|||
LSTM1STK |
5 m (16.40 ft) |
|||
LSTM2STK |
7 m (22.97 ft) |
Table 6 shows the supported QSFP+ modules.
Table 6 QSFP+ module specifications
Module |
Central wavelength |
Connector type |
Cable specifications |
Maximum transmission distance |
QSFP-40G-BIDI-SR-MM850 |
850 nm |
LC |
50/125μm MMF |
100m |
QSFP-40G-CSR4-MM850 |
850 nm |
MPO |
50/125μm MMF |
400m |
QSFP-40G-CSR4-MM850-NDDM |
850 nm |
MPO |
50/125μm MMF |
400m |
QSFP-40G-SR4-MM850 |
850 nm |
MPO |
50/125 μm MMF |
150 m (492.13 ft.) |
QSFP-40G-SR4-MM850-NDDM |
850 nm |
MPO |
50/125 μm MMF |
150 m (492.13 ft.) |
QSFP-40G-LR4-WDM1300 |
1271 nm 1291 nm 1311 nm 1331 nm |
LC |
9/125 μm single-mode optical fiber |
10 km (6.21 miles) |
QSFP-40G-LR4L-WDM1300 |
1271 nm 1291 nm 1311 nm 1331 nm |
LC |
9/125 μm single-mode optical fiber |
2 km (1.24 miles) |
Table 7 describes the specifications of the QSFP+ DAC cables that used for connecting 40G QSFP+ ports.
Table 7 QSFP+ DAC cable specifications
QSFP+ DAC cable |
Cable length |
Data rate |
Cable type |
LSWM1QSTK0 |
1 m (3.28 ft) |
40 Gbps |
QSFP+ DAC cables |
LSWM1QSTK1 |
3 m (9.84 ft) |
||
LSWM1QSTK2 |
5 m (16.40 ft) |
Table 8 describes the specifications of the QSFP+ to SFP+ cables that used for connecting 40G QSFP+ ports to 10G SFP+ ports.
Table 8 QSFP+ to SFP+ cable specifications
QSFP+ to SFP+ cable |
Cable length |
Data rate |
Cable type |
LSWM1QSTK3 |
1 m (3.28 ft) |
40 Gbps |
40G QSFP+ to 4 × 10G SFP+ cables |
LSWM1QSTK4 |
3 m (9.84 ft) |
||
LSWM1QSTK5 |
5 m (16.40 ft.) |
Table 9 describes the specifications of the QSFP+ fiber cables that used for connecting 40G QSFP+ ports.
Table 9 QSFP+ fiber cables available for the QSFP+ ports
QSFP+ fiber cable |
Cable length |
Data rate |
Remarks |
QSFP-40G-D-AOC-7M |
7 m (22.97 ft) |
40 Gbps |
For connecting 40G QSFP+ ports |
QSFP-40G-D-AOC-10M |
10 m (32.81 ft) |
||
QSFP-40G-D-AOC-20M |
20 m (65.62 ft) |
Table 10shows the supported QSFP28 modules.
Table 10 QSFP28 module specifications
Transceiver module |
Central wavelength |
Connector |
Cable specifications |
Maximum transmission distance |
QSFP-100G-SR4-MM850 |
850 nm |
MPO (PC polished, 12-fiber) |
50/125 μm multimode optical fiber |
100 m (328.08 ft) |
3 Related documentation
For module installation, see H3C S7500E Switch Series Installation Guide.
For software upgrade, see the release notes for the device.
Copyright © 2017-2018 New H3C Technologies Co., Ltd.
The information in this document is subject to change without notice.