H3C SecPath M9000-AI-E16 NSQM5SUP16A1 Supervisor Engine Module Card Manual-5PW101

HomeSupportSecurityH3C SecPath M9000-AI-EInstall & UpgradeMPU Card ManualsH3C SecPath M9000-AI-E16 NSQM5SUP16A1 Supervisor Engine Module Card Manual-5PW101

H3C SecPath M9000-AI-E16 NSQM5SUP16A1 supervisor engine module

1  Identifier

The module identifier NSQM5SUP16A1 is in the upper left corner of the front panel.

2  Specifications

The NSQM5SUP16A1 supervisor engine module (SEM, also called MPU) provides one console port, two copper management Ethernet ports, and two fiber management Ethernet ports.

Figure 1 Front panel

(1) Console port (CONSOLE)

(2) Copper management Ethernet ports

(3) Fiber management Ethernet ports

(4) USB port (reserved)

(5) Power supply status LED (PWR)

(6) Slot status LEDs (SLOT)

(7) Active/standby status LED (ACTIVE)

(8) Captive screw

(9) Reset button (RESET)

(10) Fan tray status LED (FAN)

(11) Fiber management Ethernet port LED

(12) Copper management Ethernet port LED

(13) Mini USB console port (reserved)

(14) Ejector lever

 

Table 1 Module specifications

Item

Specification

Memory

8 GB (DDR3 SDRAM)

Dimensions (H × W × D)

44.5 × 284.4 × 511.9 mm (1.75 × 11.20 × 20.15 in)

Power consumption

35 W to 45 W

Weight

4 kg (8.82 lb)

Hot swapping

Supported

Port

·     1 × console port

·     1 × mini USB console port

·     1 × USB 2.0 port (host port)

·     4 × management Ethernet ports, including two copper management Ethernet ports and two fiber management Ethernet ports

Compatible device models and slots

M9000-AI-E16 multiservice security gateway (slots 8 and 9)

 

IMPORTANT

IMPORTANT:

·     To connect a port to a management Ethernet port on the module, configure the same data rate and duplex mode for the two ports.

·     When updating the software or BootWare from BootWare, you can only use a copper management Ethernet port rather than a fiber management Ethernet port to transfer the software image files.

 

Table 2 Console port specifications

Item

Specification

Connector type

RJ-45

Interface standard

RS-232

Transmission baud rate

9600 bps (default) to 115200 bps

Transmission medium

Asynchronous serial cable

Transmission distance

≤ 15 m (49.21 ft)

Services

·     Provides connection to an ASCII terminal.

·     Provides connection to the serial port of a local PC running terminal emulation program.

·     Supports the command line interface (CLI)

 

Table 3 Copper management Ethernet port specifications

Item

Specification

Connector type

RJ-45

Interface standard

802.3, 802.3u, and 802.3ab

Interface type

MDI/MDIX autosensing

Transmission medium

Category-5 (or above) twisted pair cable

Transmission distance

100 m (328.08 ft)

Transmission rate and duplex mode

·     10 Mbps, half/full duplex

·     100 Mbps, half/full duplex

·     1000 Mbps, full duplex

 

Table 4 Fiber management Ethernet port specifications

Item

Specification

Connector type

LC

Transmission medium and maximum transmission distance

SFP transceiver modules: see Table 5.

Interface standard

802.3, 802.3u, and 802.3ab

Transmission rate and duplex mode

1000 Mbps, full duplex

 

Table 5 SFP module specifications

Module

Central wavelength

Connector type

Cable specifications

Maximum transmission distance

SFP-GE-SX-MM850-A

850 nm

LC

50/125 µm multi-mode optical fiber (MMF)

550 m (1804.46 ft)

SFP-GE-LX-SM1310-A

1310 nm

LC

9/125 µm single-mode optical fiber (SMF)

10 km (6.21 miles)

3  LEDs

Table 6 LED description

LED

Status

Description

Copper management Ethernet port LED/Fiber management Ethernet port LED

Flashing

A link is present on the port and the port is sending or receiving data.

On

A link is present on the port.

Off

No link is present on the port.

Power supply status LED (PWR)

Steady green

All the installed power supplies are operating correctly.

Steady red

A minimum of one power supply has no power output.

Possible reasons include:

·     The power supply is faulty.

·     The switch for the power supply is turned off.

·     The power cord is connected incorrectly.

·     The external power supply system is powered off.

Off

·     No power supply is present in the device.

·     All the installed power supplies have no power output.
Possible reasons include:

¡     The power supplies are faulty.

¡     The switches for the power supplies are turned off.

¡     The power cords are connected incorrectly.

¡     The external power supply system is powered off.

Fan tray status LED (FAN)

Steady green

All the fan trays are operating correctly.

Steady red

A fan tray is faulty, or no fan tray is present.

Off

No power is present on the device.

Slot status LED (SLOT)

Steady green

The module in the slot has not started loading software.

Fast flashing green (4 Hz)

The module in the slot is loading software.

Slow flashing green (0.5 Hz)

The module in the slot is operating correctly.

Steady red

The temperature of the module has reached the high-temperature warning threshold or dropped below the low-temperature threshold.

Off

No module is present in the slot.

Active/standby status LED (ACTIVE)

On

The SEM is operating in active state.

Off

·     The SEM is operating in standby state.

·     The SEM is faulty. (You can examine also the slot status LED for the SEM to determine whether a fault has occurred.)

 

4  Related documentation

For information about upgrading the SEM software, see the release notes.

For information about installing the SEM, see the installation guide for the device.

 

 

Copyright © 2020 New H3C Technologies Co., Ltd.

The information in this document is subject to change without notice.

  • Cloud & AI
  • InterConnect
  • Intelligent Computing
  • Security
  • SMB Products
  • Intelligent Terminal Products
  • Product Support Services
  • Technical Service Solutions
All Services
  • Resource Center
  • Policy
  • Online Help
All Support
  • Become a Partner
  • Partner Resources
  • Partner Business Management
All Partners
  • Profile
  • News & Events
  • Online Exhibition Center
  • Contact Us
All About Us
新华三官网