H3C Fixed-Port Switches System Log Messages Reference-R66xx-6W100

HomeSupportResource CenterDiagnose & MaintainH3C Fixed-Port Switches System Log Messages Reference-R66xx-6W100

 

H3C Fixed-Port Switches

System Log Messages Reference – R66xx

 

 

This manual is applicable to the following switches and software versions:

 

S5560X-EI Switch Series (Release 6615P03 and later)

S6520X-HI Switch Series (Release 6615P03 and later)

S6520X-EI Switch Series (Release 6615P03 and later)

S6520X-SI Switch Series (Release 6615P03 and later)

S5560X-HI Switch Series (Release 6615P03 and later)

S6813 Switch Series (Release 6615P03 and later)

S6812 Switch Series (Release 6615P03 and later)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Document version: 6W100-20220415

Copyright © 2022 New H3C Technologies Co., Ltd. All rights reserved.

No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of New H3C Technologies Co., Ltd.

Except for the trademarks of New H3C Technologies Co., Ltd., any trademarks that may be mentioned in this document are the property of their respective owners.

The information in this document is subject to change without notice.


Contents

Introduction· 1

System log message format 1

Managing and obtaining system log messages· 3

Obtaining log messages from the console terminal 3

Obtaining log messages from a monitor terminal 4

Obtaining log messages from the log buffer 4

Obtaining log messages from the log file· 4

Obtaining log messages from a log host 4

Software module list 4

Using this document 9

AAA messages· 10

AAA_FAILURE· 10

AAA_LAUNCH· 10

AAA_SUCCESS· 11

ACL messages· 12

ACL_ACCELERATE_NO_RES· 12

ACL_ACCELERATE_NONCONTIGUOUSMASK· 12

ACL_ACCELERATE_NOT_SUPPORT· 12

ACL_ACCELERATE_NOT_SUPPORTHOPBYHOP· 13

ACL_ACCELERATE_NOT_SUPPORTMULTITCPFLAG·· 13

ACL_ACCELERATE_UNK_ERR· 13

ACL_IPV6_STATIS_INFO·· 14

ACL_NO_MEM·· 14

ACL_STATIS_INFO·· 14

ANCP messages· 15

ANCP_INVALID_PACKET· 15

APMGR messages· 16

APMGR_AC_MEM_ALERT· 16

APMGR_ADD_AP_FAIL· 16

APMGR_ADDBAC_INFO·· 17

APMGR_AP_OFFLINE· 17

APMGR_AP_ONLINE· 17

APMGR_CWC_IMG_DOWNLOAD_COMPLETE· 18

APMGR_CWC_IMG_DOWNLOAD_START· 18

APMGR_CWC_IMG_NO_ENOUGH_SPACE· 18

APMGR_CWC_LOCAL_AC_DOWN· 19

APMGR_CWC_LOCAL_AC_UP· 19

APMGR_CWC_REBOOT· 20

APMGR_CWC_RUN_DOWNLOAD_COMPLETE· 20

APMGR_CWC_RUN_DOWNLOAD_START· 20

APMGR_CWC_RUN_NO_ENOUGH_SPACE· 21

APMGR_CWC_TUNNEL_DOWN· 21

APMGR_CWC_TUNNEL_UP· 22

APMGR_CWS_IMG_DOWNLOAD_COMPLETE· 22

APMGR_CWS_IMG_DOWNLOAD_START· 22

APMGR_CWS_LOCAL_AC_DOWN· 23

APMGR_CWS_LOCAL_AC_UP· 23

APMGR_CWS_RUN_DOWNLOAD_COMPLETE· 24

APMGR_CWS_RUN_DOWNLOAD_START· 24

APMGR_CWS_TUNNEL_DOWN· 25

APMGR_CWS_TUNNEL_UP· 25

APMGR_DELBAC_INFO·· 26

APMGR_LOCAL_AC_OFFLINE· 26

APMGR_LOCAL_AC_ONLINE· 26

ARP messages· 27

ARP_ACTIVE_ACK_NO_REPLY· 27

ARP_ACTIVE_ACK_NOREQUESTED_REPLY· 27

ARP_BINDRULETOHW_FAILED·· 28

ARP_DETECTION_LOG·· 28

ARP_DUPLICATE_IPADDR_DETECT· 29

ARP_DYNAMIC· 29

ARP_DYNAMIC_IF· 30

ARP_DYNAMIC_SLOT· 30

ARP_ENTRY_CONFLICT· 31

ARP_ENTRY_ENOUGHRESOURCE· 31

ARP_ENTRY_INCONSISTENT· 32

ARP_ENTRY_NORESOURCE· 33

ARP_HOST_IP_CONFLICT· 33

ARP_LOCALPROXY_ENABLE_FAILED·· 34

ARP_PKTQUE_ALERT· 34

ARP_RATE_EXCEEDED·· 34

ARP_RATELIMIT_NOTSUPPORT· 35

ARP_SENDER_IP_INVALID·· 35

ARP_SENDER_MAC_INVALID·· 36

ARP_SENDER_SMACCONFLICT· 36

ARP_SENDER_SMACCONFLICT_VSI 37

ARP_SOURCE_SUPPRESSION· 37

ARP_SRC_MAC_FOUND_ATTACK· 38

ARP_SUP_ENABLE_FAILED·· 38

ARP_TARGET_IP_INVALID·· 38

ARP_THRESHOLD_REACHED·· 39

ARP_USER_DUPLICATE_IPADDR_DETECT· 39

ARP_USER_MOVE_DETECT· 40

DUPIFIP· 40

DUPIP· 41

DUPVRRPIP· 41

ATK messages· 42

ATK_ICMP_ADDRMASK_REQ·· 42

ATK_ICMP_ADDRMASK_REQ_RAW·· 43

ATK_ICMP_ADDRMASK_REQ_RAW_SZ· 44

ATK_ICMP_ADDRMASK_REQ_SZ· 45

ATK_ICMP_ADDRMASK_RPL· 46

ATK_ICMP_ADDRMASK_RPL_RAW·· 47

ATK_ICMP_ADDRMASK_RPL_RAW_SZ· 48

ATK_ICMP_ADDRMASK_RPL_SZ· 49

ATK_ICMP_ECHO_REQ·· 50

ATK_ICMP_ECHO_REQ_RAW·· 51

ATK_ICMP_ECHO_REQ_RAW_SZ· 52

ATK_ICMP_ECHO_REQ_SZ· 53

ATK_ICMP_ECHO_RPL· 54

ATK_ICMP_ECHO_RPL_RAW·· 55

ATK_ICMP_ECHO_RPL_RAW_SZ· 56

ATK_ICMP_ECHO_RPL_SZ· 57

ATK_ICMP_FLOOD·· 58

ATK_ICMP_FLOOD_SZ· 58

ATK_ICMP_INFO_REQ·· 59

ATK_ICMP_INFO_REQ_RAW·· 60

ATK_ICMP_INFO_REQ_RAW_SZ· 61

ATK_ICMP_INFO_REQ_SZ· 62

ATK_ICMP_INFO_RPL· 63

ATK_ICMP_INFO_RPL_RAW·· 64

ATK_ICMP_INFO_RPL_RAW_SZ· 65

ATK_ICMP_INFO_RPL_SZ· 66

ATK_ICMP_LARGE· 67

ATK_ICMP_LARGE_RAW·· 68

ATK_ICMP_LARGE_RAW_SZ· 68

ATK_ICMP_LARGE_SZ· 69

ATK_ICMP_PARAPROBLEM·· 70

ATK_ICMP_PARAPROBLEM_RAW·· 71

ATK_ICMP_PARAPROBLEM_RAW_SZ· 72

ATK_ICMP_PARAPROBLEM_SZ· 73

ATK_ICMP_PINGOFDEATH· 74

ATK_ICMP_PINGOFDEATH_RAW·· 75

ATK_ICMP_PINGOFDEATH_RAW_SZ· 75

ATK_ICMP_PINGOFDEATH_SZ· 76

ATK_ICMP_REDIRECT· 77

ATK_ICMP_REDIRECT_RAW·· 78

ATK_ICMP_REDIRECT_RAW_SZ· 79

ATK_ICMP_REDIRECT_SZ· 80

ATK_ICMP_SMURF· 81

ATK_ICMP_SMURF_RAW·· 82

ATK_ICMP_SMURF_RAW_SZ· 83

ATK_ICMP_SMURF_SZ· 84

ATK_ICMP_SOURCEQUENCH· 85

ATK_ICMP_SOURCEQUENCH_RAW·· 86

ATK_ICMP_SOURCEQUENCH_RAW_SZ· 87

ATK_ICMP_SOURCEQUENCH_SZ· 88

ATK_ICMP_TIMEEXCEED·· 89

ATK_ICMP_TIMEEXCEED_RAW·· 90

ATK_ICMP_TIMEEXCEED_RAW_SZ· 91

ATK_ICMP_TIMEEXCEED_SZ· 92

ATK_ICMP_TRACEROUTE· 93

ATK_ICMP_TRACEROUTE_RAW·· 94

ATK_ICMP_TRACEROUTE_RAW_SZ· 94

ATK_ICMP_TRACEROUTE_SZ· 95

ATK_ICMP_TSTAMP_REQ·· 96

ATK_ICMP_TSTAMP_REQ_RAW·· 97

ATK_ICMP_TSTAMP_REQ_RAW_SZ· 98

ATK_ICMP_TSTAMP_REQ_SZ· 99

ATK_ICMP_TSTAMP_RPL· 100

ATK_ICMP_TSTAMP_RPL_RAW·· 101

ATK_ICMP_TSTAMP_RPL_RAW_SZ· 102

ATK_ICMP_TSTAMP_RPL_SZ· 103

ATK_ICMP_TYPE· 104

ATK_ICMP_TYPE_RAW·· 105

ATK_ICMP_TYPE_RAW_SZ· 106

ATK_ICMP_TYPE_SZ· 107

ATK_ICMP_UNREACHABLE· 108

ATK_ICMP_UNREACHABLE_RAW·· 109

ATK_ICMP_UNREACHABLE_RAW_SZ· 110

ATK_ICMP_UNREACHABLE_SZ· 111

ATK_ICMPV6_DEST_UNREACH· 112

ATK_ICMPV6_DEST_UNREACH_RAW·· 113

ATK_ICMPV6_DEST_UNREACH_RAW_SZ· 113

ATK_ICMPV6_DEST_UNREACH_SZ· 114

ATK_ICMPV6_ECHO_REQ·· 115

ATK_ICMPV6_ECHO_REQ_RAW·· 116

ATK_ICMPV6_ECHO_REQ_RAW_SZ· 116

ATK_ICMPV6_ECHO_REQ_SZ· 117

ATK_ICMPV6_ECHO_RPL· 118

ATK_ICMPV6_ECHO_RPL_RAW·· 119

ATK_ICMPV6_ECHO_RPL_RAW_SZ· 119

ATK_ICMPV6_ECHO_RPL_SZ· 120

ATK_ICMPV6_FLOOD·· 121

ATK_ICMPV6_FLOOD_SZ· 121

ATK_ICMPV6_GROUPQUERY· 122

ATK_ICMPV6_GROUPQUERY_RAW·· 123

ATK_ICMPV6_GROUPQUERY_RAW_SZ· 123

ATK_ICMPV6_GROUPQUERY_SZ· 124

ATK_ICMPV6_GROUPREDUCTION· 125

ATK_ICMPV6_GROUPREDUCTION_RAW·· 126

ATK_ICMPV6_GROUPREDUCTION_RAW_SZ· 126

ATK_ICMPV6_GROUPREDUCTION_SZ· 127

ATK_ICMPV6_GROUPREPORT· 128

ATK_ICMPV6_GROUPREPORT_RAW·· 129

ATK_ICMPV6_GROUPREPORT_RAW_SZ· 129

ATK_ICMPV6_GROUPREPORT_SZ· 130

ATK_ICMPV6_LARGE· 131

ATK_ICMPV6_LARGE_RAW·· 131

ATK_ICMPV6_LARGE_RAW_SZ· 132

ATK_ICMPV6_LARGE_SZ· 132

ATK_ICMPV6_PACKETTOOBIG·· 133

ATK_ICMPV6_PACKETTOOBIG_RAW·· 134

ATK_ICMPV6_PACKETTOOBIG_RAW_SZ· 134

ATK_ICMPV6_PACKETTOOBIG_SZ· 135

ATK_ICMPV6_PARAPROBLEM·· 136

ATK_ICMPV6_PARAPROBLEM_RAW·· 137

ATK_ICMPV6_PARAPROBLEM_RAW_SZ· 137

ATK_ICMPV6_PARAPROBLEM_SZ· 138

ATK_ICMPV6_TIMEEXCEED·· 139

ATK_ICMPV6_TIMEEXCEED_RAW·· 140

ATK_ICMPV6_TIMEEXCEED_RAW_SZ· 140

ATK_ICMPV6_TIMEEXCEED_SZ· 141

ATK_ICMPV6_TRACEROUTE· 142

ATK_ICMPV6_TRACEROUTE_RAW·· 143

ATK_ICMPV6_TRACEROUTE_RAW_SZ· 144

ATK_ICMPV6_TRACEROUTE_SZ· 145

ATK_ICMPV6_TYPE· 146

ATK_ICMPV6_TYPE _RAW_SZ· 147

ATK_ICMPV6_TYPE_RAW·· 147

ATK_ICMPV6_TYPE_SZ· 148

ATK_IP_OPTION· 149

ATK_IP_OPTION_RAW·· 150

ATK_IP_OPTION_RAW_SZ· 151

ATK_IP_OPTION_SZ· 152

ATK_IP4_ACK_FLOOD·· 153

ATK_IP4_ACK_FLOOD_SZ· 153

ATK_IP4_DIS_PORTSCAN· 154

ATK_IP4_DIS_PORTSCAN_SZ· 154

ATK_IP4_DNS_FLOOD·· 155

ATK_IP4_DNS_FLOOD_SZ· 155

ATK_IP4_FIN_FLOOD·· 156

ATK_IP4_FIN_FLOOD_SZ· 156

ATK_IP4_FRAGMENT· 157

ATK_IP4_FRAGMENT_RAW·· 158

ATK_IP4_FRAGMENT_RAW_SZ· 159

ATK_IP4_FRAGMENT_SZ· 160

ATK_IP4_HTTP_FLOOD·· 161

ATK_IP4_HTTP_FLOOD_SZ· 161

ATK_IP4_IMPOSSIBLE· 162

ATK_IP4_IMPOSSIBLE_RAW·· 163

ATK_IP4_IMPOSSIBLE_RAW_SZ· 164

ATK_IP4_IMPOSSIBLE_SZ· 165

ATK_IP4_IPSWEEP· 166

ATK_IP4_IPSWEEP_SZ· 166

ATK_IP4_PORTSCAN· 167

ATK_IP4_PORTSCAN_SZ· 167

ATK_IP4_RST_FLOOD·· 168

ATK_IP4_RST_FLOOD_SZ· 168

ATK_IP4_SYN_FLOOD·· 169

ATK_IP4_SYN_FLOOD_SZ· 169

ATK_IP4_SYNACK_FLOOD·· 170

ATK_IP4_SYNACK_FLOOD_SZ· 170

ATK_IP4_TCP_ALLFLAGS· 171

ATK_IP4_TCP_ALLFLAGS_RAW·· 172

ATK_IP4_TCP_ALLFLAGS_RAW_SZ· 172

ATK_IP4_TCP_ALLFLAGS_SZ· 173

ATK_IP4_TCP_FINONLY· 174

ATK_IP4_TCP_FINONLY_RAW·· 175

ATK_IP4_TCP_FINONLY_RAW_SZ· 175

ATK_IP4_TCP_FINONLY_SZ· 176

ATK_IP4_TCP_INVALIDFLAGS· 177

ATK_IP4_TCP_INVALIDFLAGS_RAW·· 178

ATK_IP4_TCP_INVALIDFLAGS_RAW_SZ· 179

ATK_IP4_TCP_INVALIDFLAGS_SZ· 180

ATK_IP4_TCP_LAND·· 181

ATK_IP4_TCP_LAND_RAW·· 182

ATK_IP4_TCP_LAND_RAW_SZ· 182

ATK_IP4_TCP_LAND_SZ· 183

ATK_IP4_TCP_NULLFLAG·· 184

ATK_IP4_TCP_NULLFLAG_RAW·· 185

ATK_IP4_TCP_NULLFLAG_RAW_SZ· 185

ATK_IP4_TCP_NULLFLAG_SZ· 186

ATK_IP4_TCP_SYNFIN· 187

ATK_IP4_TCP_SYNFIN_RAW·· 188

ATK_IP4_TCP_SYNFIN_RAW_SZ· 188

ATK_IP4_TCP_SYNFIN_SZ· 189

ATK_IP4_TCP_WINNUKE· 190

ATK_IP4_TCP_WINNUKE_RAW·· 191

ATK_IP4_TCP_WINNUKE_RAW_SZ· 191

ATK_IP4_TCP_WINNUKE_SZ· 192

ATK_IP4_TEARDROP· 193

ATK_IP4_TEARDROP_RAW·· 194

ATK_IP4_TEARDROP_RAW_SZ· 195

ATK_IP4_TEARDROP_SZ· 196

ATK_IP4_TINY_FRAGMENT· 197

ATK_IP4_TINY_FRAGMENT_RAW·· 198

ATK_IP4_TINY_FRAGMENT_RAW_SZ· 199

ATK_IP4_TINY_FRAGMENT_SZ· 200

ATK_IP4_UDP_BOMB· 201

ATK_IP4_UDP_BOMB_RAW·· 202

ATK_IP4_UDP_BOMB_RAW_SZ· 203

ATK_IP4_UDP_BOMB_SZ· 204

ATK_IP4_UDP_FLOOD·· 205

ATK_IP4_UDP_FLOOD_SZ· 205

ATK_IP4_UDP_FRAGGLE· 206

ATK_IP4_UDP_FRAGGLE_RAW·· 207

ATK_IP4_UDP_FRAGGLE_RAW_SZ· 207

ATK_IP4_UDP_FRAGGLE_SZ· 208

ATK_IP4_UDP_SNORK· 209

ATK_IP4_UDP_SNORK_RAW·· 210

ATK_IP4_UDP_SNORK_RAW_SZ· 210

ATK_IP4_UDP_SNORK_SZ· 211

ATK_IP6_ACK_FLOOD·· 212

ATK_IP6_ACK_FLOOD_SZ· 212

ATK_IP6_DIS_PORTSCAN· 213

ATK_IP6_DIS_PORTSCAN_SZ· 213

ATK_IP6_DNS_FLOOD·· 214

ATK_IP6_DNS_FLOOD_SZ· 214

ATK_IP6_FIN_FLOOD·· 215

ATK_IP6_FIN_FLOOD_SZ· 215

ATK_IP6_FRAGMENT· 216

ATK_IP6_FRAGMENT_RAW·· 217

ATK_IP6_FRAGMENT_RAW_SZ· 217

ATK_IP6_FRAGMENT_SZ· 218

ATK_IP6_HTTP_FLOOD·· 219

ATK_IP6_HTTP_FLOOD_SZ· 219

ATK_IP6_IMPOSSIBLE· 220

ATK_IP6_IMPOSSIBLE_RAW·· 221

ATK_IP6_IMPOSSIBLE_RAW_SZ· 221

ATK_IP6_IMPOSSIBLE_SZ· 222

ATK_IP6_IPSWEEP· 222

ATK_IP6_IPSWEEP_SZ· 223

ATK_IP6_PORTSCAN· 223

ATK_IP6_PORTSCAN_SZ· 224

ATK_IP6_RST_FLOOD·· 224

ATK_IP6_RST_FLOOD_SZ· 225

ATK_IP6_SYN_FLOOD·· 225

ATK_IP6_SYN_FLOOD_SZ· 226

ATK_IP6_SYNACK_FLOOD·· 226

ATK_IP6_SYNACK_FLOOD_SZ· 227

ATK_IP6_TCP_ALLFLAGS· 227

ATK_IP6_TCP_ALLFLAGS_RAW·· 228

ATK_IP6_TCP_ALLFLAGS_RAW_SZ· 228

ATK_IP6_TCP_ALLFLAGS_SZ· 229

ATK_IP6_TCP_FINONLY· 230

ATK_IP6_TCP_FINONLY_RAW·· 230

ATK_IP6_TCP_FINONLY_RAW_SZ· 231

ATK_IP6_TCP_FINONLY_SZ· 231

ATK_IP6_TCP_INVALIDFLAGS· 232

ATK_IP6_TCP_INVALIDFLAGS_RAW·· 233

ATK_IP6_TCP_INVALIDFLAGS_RAW_SZ· 234

ATK_IP6_TCP_INVALIDFLAGS_SZ· 235

ATK_IP6_TCP_LAND·· 236

ATK_IP6_TCP_LAND_RAW·· 236

ATK_IP6_TCP_LAND_RAW_SZ· 237

ATK_IP6_TCP_LAND_SZ· 237

ATK_IP6_TCP_NULLFLAG·· 238

ATK_IP6_TCP_NULLFLAG_RAW·· 238

ATK_IP6_TCP_NULLFLAG_RAW_SZ· 239

ATK_IP6_TCP_NULLFLAG_SZ· 239

ATK_IP6_TCP_SYNFIN· 240

ATK_IP6_TCP_SYNFIN_RAW·· 240

ATK_IP6_TCP_SYNFIN_RAW_SZ· 241

ATK_IP6_TCP_SYNFIN_SZ· 241

ATK_IP6_TCP_WINNUKE· 242

ATK_IP6_TCP_WINNUKE_RAW·· 242

ATK_IP6_TCP_WINNUKE_RAW_SZ· 243

ATK_IP6_TCP_WINNUKE_SZ· 243

ATK_IP6_UDP_FLOOD·· 244

ATK_IP6_UDP_FLOOD_SZ· 244

ATK_IP6_UDP_FRAGGLE· 245

ATK_IP6_UDP_FRAGGLE_RAW·· 245

ATK_IP6_UDP_FRAGGLE_RAW_SZ· 246

ATK_IP6_UDP_FRAGGLE_SZ· 246

ATK_IP6_UDP_SNORK· 247

ATK_IP6_UDP_SNORK_RAW·· 247

ATK_IP6_UDP_SNORK_RAW_SZ· 248

ATK_IP6_UDP_SNORK_SZ· 248

ATK_IPOPT_ABNORMAL· 249

ATK_IPOPT_ABNORMAL_RAW·· 250

ATK_IPOPT_ABNORMAL_RAW_SZ· 251

ATK_IPOPT_ABNORMAL_SZ· 252

ATK_IPOPT_LOOSESRCROUTE· 253

ATK_IPOPT_LOOSESRCROUTE_RAW·· 254

ATK_IPOPT_LOOSESRCROUTE_RAW_SZ· 255

ATK_IPOPT_LOOSESRCROUTE_SZ· 256

ATK_IPOPT_RECORDROUTE· 257

ATK_IPOPT_RECORDROUTE_RAW·· 258

ATK_IPOPT_RECORDROUTE_RAW_SZ· 259

ATK_IPOPT_RECORDROUTE_SZ· 260

ATK_IPOPT_ROUTEALERT· 261

ATK_IPOPT_ROUTEALERT_RAW·· 262

ATK_IPOPT_ROUTEALERT_RAW_SZ· 263

ATK_IPOPT_ROUTEALERT_SZ· 264

ATK_IPOPT_SECURITY· 265

ATK_IPOPT_SECURITY_RAW·· 266

ATK_IPOPT_SECURITY_RAW_SZ· 267

ATK_IPOPT_SECURITY_SZ· 268

ATK_IPOPT_STREAMID·· 269

ATK_IPOPT_STREAMID_RAW·· 270

ATK_IPOPT_STREAMID_RAW_SZ· 271

ATK_IPOPT_STREAMID_SZ· 272

ATK_IPOPT_STRICTSRCROUTE· 273

ATK_IPOPT_STRICTSRCROUTE_RAW·· 274

ATK_IPOPT_STRICTSRCROUTE_RAW_SZ· 275

ATK_IPOPT_STRICTSRCROUTE_SZ· 276

ATK_IPOPT_TIMESTAMP· 277

ATK_IPOPT_TIMESTAMP_RAW·· 278

ATK_IPOPT_TIMESTAMP_RAW_SZ· 279

ATK_IPOPT_TIMESTAMP_SZ· 280

ATK_IPV6_EXT_HEADER· 281

ATK_IPV6_EXT_HEADER_RAW·· 282

ATK_IPV6_EXT_HEADER_RAW_SZ· 282

ATK_IPV6_EXT_HEADER_SZ· 283

ATM·· 284

ATM_PVCDOWN· 284

ATM_PVCUP· 284

BFD messages· 286

BFD_CHANGE_FSM·· 286

BFD_REACHED_UPPER_LIMIT· 286

BGP messages· 287

BGP_EXCEED_ROUTE_LIMIT· 287

BGP_REACHED_THRESHOLD·· 287

BGP_LOG_ROUTE_FLAP· 288

BGP_MEM_ALERT· 288

BGP_PEER_LICENSE_REACHED·· 288

BGP_ROUTE_LICENSE_REACHED·· 289

BGP_STATE_CHANGED·· 290

BGP_STATE_CHANGED_REASON· 291

BLS messages· 292

BLS_ENTRY_ADD·· 292

BLS_ENTRY_DEL· 292

BLS_IPV6_ENTRY_ADD·· 293

BLS_IPV6_ENTRY_DEL· 293

CFD messages· 294

CFD_CROSS_CCM·· 294

CFD_ERROR_CCM·· 294

CFD_LOST_CCM·· 295

CFD_RECEIVE_CCM·· 295

CFGMAN messages· 296

CFGMAN_ARCHIVE_SCP_FAIL· 296

CFGMAN_CFGCHANGED·· 296

CFGMAN_EXIT_FROM_CONFIGURE· 297

CFGMAN_OPTCOMPLETION· 297

CFG_SAVE_FAILED·· 299

CFG_SET_NEXTCFG_FAILED·· 300

CONNLMT messages· 301

CONNLMT_IPV4_OVERLOAD·· 301

CONNLMT_IPV4_RECOVER· 302

CONNLMT_IPV6_OVERLOAD·· 303

CONNLMT_IPV6_RECOVER· 304

DEV messages· 305

AUTOSWITCH_FAULT· 305

BOARD_REBOOT· 305

BOARD_REMOVED·· 306

BOARD_RUNNING_FAULT· 306

BOARD_RUNNING_FAULT_REBOOT· 306

BOARD_STATE_FAULT· 307

BOARD_STATE_NORMAL· 307

CFCARD_INSERTED·· 307

CFCARD_REMOVED·· 308

CHASSIS_REBOOT· 308

DEV_CLOCK_CHANGE· 308

DEV_FAULT_TOOLONG·· 309

DEV_MNT_LogToIC· 309

FAN_ABSENT· 310

FAN_DIRECTION_NOT_PREFERRED·· 310

FAN_FAILED·· 311

FAN_RECOVERED·· 311

MAD_DETECT· 312

MAD_PROC· 312

POWER_ABSENT· 313

POWER_FAILED·· 313

POWER_MONITOR_ABSENT· 314

POWER_MONITOR_FAILED·· 314

POWER_MONITOR_RECOVERED·· 315

POWER_RECOVERED·· 315

RPS_ABSENT· 316

RPS_FAILED·· 316

RPS_NORMAL· 317

SUBCARD_FAULT· 317

SUBCARD_INSERTED·· 318

SUBCARD_REBOOT· 318

SUBCARD_REMOVED·· 319

SYSTEM_REBOOT· 319

TEMPERATURE_ALARM·· 320

TEMPERATURE_LOW·· 321

TEMPERATURE_NORMAL· 322

TEMPERATURE_SHUTDOWN· 323

TEMPERATURE_WARNING·· 324

TIMER_CREATE_FAILED_FIRST· 325

TIMER_CREATE_FAILED_MORE· 326

VCHK_VERSION_INCOMPATIBLE· 326

DHCP·· 327

DHCP_NOTSUPPORTED·· 327

DHCP_NORESOURCES· 327

DHCPR·· 328

DHCPR_SERVERCHANGE· 328

DHCPR_SWITCHMASTER· 328

DHCPS messages· 329

DHCPS_ALLOCATE_IP· 329

DHCPS_CONFLICT_IP· 329

DHCPS_EXTEND_IP· 330

DHCPS_FILE· 330

DHCPS_RECLAIM_IP· 331

DHCPS_VERIFY_CLASS· 331

DHCPS6 messages· 332

DHCPS6_ALLOCATE_ADDRESS· 332

DHCPS6_ALLOCATE_PREFIX· 332

DHCPS6_CONFLICT_ADDRESS· 333

DHCPS6_EXTEND_ADDRESS· 333

DHCPS6_EXTEND_PREFIX· 334

DHCPS6_FILE· 334

DHCPS6_RECLAIM_ADDRESS· 335

DHCPS6_RECLAIM_PREFIX· 335

DHCPSP4· 336

DHCPSP4_FILE· 336

DHCPSP4_UNTRUSTED_SERVER· 336

DHCPSP6· 337

DHCPSP6_FILE· 337

DIAG messages· 338

CPU_MINOR_RECOVERY· 338

CPU_MINOR_THRESHOLD·· 339

CPU_SEVERE_RECOVERY· 340

CPU_SEVERE_THRESHOLD·· 341

CPU_USAGE_LASTMINUTE· 342

DIAG_FD_UPLIMIT_REACHED·· 343

DIAG_FD_UPLIMIT_TO_REACH· 343

MEM_ALERT· 344

MEM_BELOW_THRESHOLD·· 345

MEM_EXCEED_THRESHOLD·· 346

MEM_USAGE· 346

DLDP messages· 347

DLDP_AUTHENTICATION_FAILED·· 347

DLDP_LINK_BIDIRECTIONAL· 347

DLDP_LINK_SHUTMODECHG·· 348

DLDP_LINK_UNIDIRECTIONAL· 348

DLDP_NEIGHBOR_AGED·· 349

DLDP_NEIGHBOR_CONFIRMED·· 349

DLDP_NEIGHBOR_DELETED·· 350

DOT1X messages· 351

DOT1X_CONFIG_NOTSUPPORT· 351

DOT1X_LOGIN_FAILURE· 351

DOT1X_LOGIN_SUCC· 352

DOT1X_LOGIN_SUCC (in open mode) 352

DOT1X_LOGOFF· 353

DOT1X_LOGOFF (in open mode) 353

DOT1X_LOGOFF_ABNORMAL· 354

DOT1X_LOGOFF_ABNORMAL (in open mode) 355

DOT1X_MACBINDING_EXIST· 355

DOT1X_NOTENOUGH_EADFREEIP_RES· 356

DOT1X_NOTENOUGH_EADFREEMSEG_RES· 356

DOT1X_NOTENOUGH_EADFREERULE_RES· 356

DOT1X_NOTENOUGH_EADMACREDIR_RES· 357

DOT1X_NOTENOUGH_EADPORTREDIR_RES· 357

DOT1X_NOTENOUGH_ENABLEDOT1X_RES· 357

DOT1X_PEXAGG_NOMEMBER_RES· 358

DOT1X_SMARTON_FAILURE· 358

DOT1X_UNICAST_NOT_EFFECTIVE· 358

DRNI 360

DRNI_AUTORECOVERY_TIMEOUT· 360

DRNI_GLBCHECK_CONSISTENCY· 360

DRNI_GLBCHECK_INCONSISTENCY· 361

DRNI_IFCHECK_CONSISTENCY· 361

DRNI_IFCHECK_INCONSISTENCY· 361

DRNI_IFEVENT_DR_BIND·· 362

DRNI_IFEVENT_DR_GLOBALDOWN· 362

DRNI_IFEVENT_DR_GLOBALUP· 362

DRNI_IFEVENT_DR_MAC_CHANGE· 363

DRNI_IFEVENT_DR_NOSELECTED·· 363

DRNI_IFEVENT_DR_PEERBIND·· 364

DRNI_IFEVENT_DR_PEERUNBIND·· 364

DRNI_IFEVENT_DR_PEER_NOSELECTED·· 364

DRNI_IFEVENT_DR_PEER_SELECTED·· 365

DRNI_IFEVENT_DR_PRIORITY_CHANGE· 365

DRNI_IFEVENT_DR_SELECTED·· 365

DRNI_IFEVENT_DR_UNBIND·· 366

DRNI_IFEVENT_IPP_BIND·· 366

DRNI_IFEVENT_IPP_DOWN· 367

DRNI_IFEVENT_IPP_UNBIND·· 367

DRNI_IFEVENT_IPP_UP· 368

DRNI_IPP_BLOCK· 368

DRNI_IPP_UNBLOCK· 368

DRNI_KEEPALIVEINTERVAL_MISMATCH· 369

DRNI_KEEPALIVELINK_DOWN· 369

DRNI_KEEPALIVELINK_UP· 369

DRNI_KEEPALIVEPACKETS_FAILED·· 370

DRNI_DEVICE_MADDOWN· 370

DRNI_DEVICE_MADRECOVERY· 371

DRNI_SYSEVENT_DEVICEROLE_CHANGE· 371

DRNI_SYSEVENT_MAC_CHANGE· 371

DRNI_SYSEVENT_MODE_CHANGE· 372

DRNI_SYSEVENT_NUMBER_CHANGE· 372

DRNI_SYSEVENT_PRIORITY_CHANGE· 372

DRNI_VMAC_INEFFECTIVE· 373

DRVPLAT· 374

DRVPLAT_ACL_FAILD·· 374

DRVPLAT_ECMP_NO_RESOURCE· 374

DRVPLAT_IPMC_TTI_NO_RESOURCE· 375

DRVPLAT_MAC_Conflict 375

DRVPLAT_NO_ENOUGH_RESOURCE· 375

DRVPLAT_Not_Enough_Resource· 376

DRVPLAT_POE_AI_DISCONNET_AC· 376

DRVPLAT_POE_AI_DISCONNET_DELAY· 377

DRVPLAT_POE_AI_HIGH_INRUSH· 377

DRVPLAT_POE_AI_PORT_MAXPOWER· 378

DRVPLAT_POE_AI_PORT_RESTART· 379

DRVPLAT_PORT_ATTACK_OCCUR· 379

DRVPLAT_PORT_AUTONEGTION_DISABLE· 380

DRVPLAT_SOFTCAR_DROP· 381

DRVPLAT_VPN_Conflict 381

DRVPLAT_VPN_MAYBE_Conflict 382

EDEV messages· 383

ALARM_IN_REMOVED·· 383

ALARM_IN_REPORTED·· 383

EDEV_BOOTROM_UPDATE_FAILED·· 383

EDEV_BOOTROM_UPDATE_SUCCESS· 384

EDEV_FAILOVER_GROUP_STATE_CHANGE· 384

eMDI messages· 385

EMDI_INDICATOR_OVER_THRES· 385

EMDI_INDICATOR_OVER_THRES_RESUME· 386

EMDI_INSTANCE_CONFLICT_FLOW·· 386

EMDI_INSTANCE_EXCEED·· 387

EMDI_INSTANCE_SAME_FLOW·· 387

EPA messages· 388

EPA_ENDPOINT_ONLINE· 388

EPA_ENDPOINT_OFFLINE· 388

EPA_DEVICETYPE_CHANGE· 389

ERPS messages· 390

ERPS_IPP_CHECK· 390

ERPS_STATE_CHANGED·· 390

ETH messages· 391

ETH_SET_MAC_FAILED·· 391

ETHDRNI 392

ETHDRNI_MAC_INEFFECTIVE· 392

ETHOAM messages· 393

ETHOAM_CONNECTION_FAIL_DOWN· 393

ETHOAM_CONNECTION_FAIL_TIMEOUT· 393

ETHOAM_CONNECTION_FAIL_UNSATISF· 394

ETHOAM_CONNECTION_SUCCEED·· 394

ETHOAM_DISABLE· 394

ETHOAM_DISCOVERY_EXIT· 395

ETHOAM_ENABLE· 395

ETHOAM_ENTER_LOOPBACK_CTRLLED·· 395

ETHOAM_ENTER_LOOPBACK_CTRLLING·· 396

ETHOAM_LOCAL_DYING_GASP· 396

ETHOAM_LOCAL_ERROR_FRAME· 396

ETHOAM_LOCAL_ERROR_FRAME_PERIOD·· 397

ETHOAM_LOCAL_ERROR_FRAME_SECOND·· 397

ETHOAM_LOCAL_ERROR_SYMBOL· 397

ETHOAM_LOCAL_LINK_FAULT· 398

ETHOAM_LOOPBACK_EXIT· 398

ETHOAM_LOOPBACK_EXIT_ERROR_STATU· 398

ETHOAM_LOOPBACK_NO_RESOURCE· 399

ETHOAM_LOOPBACK_NOT_SUPPORT· 399

ETHOAM_QUIT_LOOPBACK_CTRLLED·· 399

ETHOAM_QUIT_LOOPBACK_CTRLLING·· 400

ETHOAM_REMOTE_CRITICAL· 400

ETHOAM_REMOTE_DYING_GASP· 400

ETHOAM_REMOTE_ERROR_FRAME· 401

ETHOAM_REMOTE_ERROR_FRAME_PERIOD·· 401

ETHOAM_REMOTE_ERROR_FRAME_SECOND·· 401

ETHOAM_REMOTE_ERROR_SYMBOL· 402

ETHOAM_REMOTE_EXIT· 402

ETHOAM_REMOTE_FAILURE_RECOVER· 402

ETHOAM_REMOTE_LINK_FAULT· 403

ETHOAM_NO_ENOUGH_RESOURCE· 403

ETHOAM_NOT_CONNECTION_TIMEOUT· 403

EVB messages· 404

EVB_AGG_FAILED·· 404

EVB_LICENSE_EXPIRE· 404

EVB_VSI_OFFLINE· 405

EVB_VSI_ONLINE· 405

EVIISIS messages· 406

EVIISIS_LICENSE_EXPIRED·· 406

EVIISIS_LICENSE_EXPIRED_TIME· 406

EVIISIS_LICENSE_UNAVAILABLE· 406

EVIISIS_NBR_CHG·· 407

FCLINK messages· 408

FCLINK_FDISC_REJECT_NORESOURCE· 408

FCLINK_FLOGI_REJECT_NORESOURCE· 408

FCOE messages· 409

FCOE_INTERFACE_NOTSUPPORT_FCOE· 409

FCOE_LAGG_BIND_ACTIVE· 409

FCOE_LAGG_BIND_DEACTIVE· 410

FCZONE messages· 411

FCZONE_DISTRIBUTE_FAILED·· 411

FCZONE_HARDZONE_DISABLED·· 411

FCZONE_HARDZONE_ENABLED·· 412

FCZONE_ISOLATE_ALLNEIGHBOR· 412

FCZONE_ISOLATE_CLEAR_VSAN· 413

FCZONE_ISOLATE_CLEAR_ALLVSAN· 413

FCZONE_ISOLATE_NEIGHBOR· 413

FGROUP messages· 414

FLOWGROUP_APPLY_FAIL· 414

FLOWGROUP_MODIFY_FAIL· 414

FIB messages· 415

FIB_FILE· 415

FIB_PREFIX_ENOUGHRESOURCE· 415

FIB_PREFIX_INCONSISTENT· 416

FIB_PREFIX_NORESOURCE· 417

FIB_VN_ENOUGHRESOURCE· 418

FIB_VN_INCONSISTENT· 419

FIB_VN_NORESOURCE· 420

FILTER messages· 421

FILTER_EXECUTION_ICMP· 421

FILTER_EXECUTION_ICMPV6· 422

FILTER_IPV4_EXECUTION· 423

FILTER_IPV6_EXECUTION· 424

FIPSNG messages· 425

FIPSNG_HARD_RESOURCE_NOENOUGH· 425

FIPSNG_HARD_RESOURCE_RESTORE· 425

FS messages· 426

FS_UNFORMATTED_PARTITION· 426

FTP messages· 427

FTP_ACL_DENY· 427

FTP_REACH_SESSION_LIMIT· 427

FTPD_AUTHOR_FAILED·· 428

gRPC messages· 429

GRPC_LOGIN· 429

GRPC_LOGIN_FAILED·· 429

GRPC_LOGOUT· 430

GRPC_SERVER_FAILED·· 430

GRPC_SUBSCRIBE_EVENT_FAILED·· 430

GRPC_RECEIVE_SUBSCRIPTION· 431

HA messages· 432

HA_BATCHBACKUP_FINISHED·· 432

HA_BATCHBACKUP_STARTED·· 432

HA_STANDBY_NOT_READY· 432

HA_STANDBY_TO_MASTER· 433

HLTH messages· 434

LIPC_COMM_FAULTY· 434

LIPC_COMM_RECOVER· 434

HQOS messages· 435

HQOS_DP_SET_FAIL· 435

HQOS_FP_SET_FAIL· 435

HQOS_POLICY_APPLY_FAIL· 436

HQOS_POLICY_APPLY_FAIL· 436

HTTPD messages· 437

HTTPD_CONNECT· 437

HTTPD_CONNECT_TIMEOUT· 437

HTTPD_DISCONNECT· 438

HTTPD_FAIL_FOR_ACL· 438

HTTPD_FAIL_FOR_ACP· 438

HTTPD_REACH_CONNECT_LIMIT· 439

IFNET messages· 440

IF_BUFFER_CONGESTION_OCCURRENCE· 440

IF_BUFFER_CONGESTION_CLEAR· 440

IF_JUMBOFRAME_WARN· 441

IF_LINKFLAP_DETECTED·· 441

INTERFACE_NOTSUPPRESSED·· 441

INTERFACE_SUPPRESSED·· 442

LINK_UPDOWN· 442

PFC_WARNING·· 443

PHY_UPDOWN· 443

PROTOCOL_UPDOWN· 443

STORM_CONSTRAIN_BELOW·· 444

STORM_CONSTRAIN_CONTROLLED·· 444

STORM_CONSTRAIN_EXCEED·· 445

STORM_CONSTRAIN_NORMAL· 445

TUNNEL_LINK_UPDOWN· 446

TUNNEL_PHY_UPDOWN· 446

VLAN_MODE_CHANGE· 446

IKE messages· 447

IKE_P1_SA_ESTABLISH_FAIL· 447

IKE_P2_SA_ESTABLISH_FAIL· 448

IKE_P2_SA_TERMINATE· 448

IKE_VERIFY_CERT_FAIL· 449

IMA·· 451

IMA_ALLOCATE_FAILED·· 451

IMA_DATA_ERROR· 451

IMA_FILE_HASH_FAILED·· 451

IMA_RM_FILE_MISS· 452

IMA_RM_HASH_MISS· 452

IMA_TEMPLATE_ERROR· 452

iNOF· 453

INOF_ADD_HOST· 453

INOF_DELETE_HOST· 454

iNQA·· 455

INQA_BWD_LOSS_EXCEED·· 455

INQA_BWD_LOSS_RECOV· 455

INQA_DEBUG_FAIL· 455

INQA_FLAG_DIFF· 456

INQA_FLAG_FAIL· 456

INQA_FLOW_DIFF· 456

INQA_FWD_LOSS_EXCEED·· 457

INQA_FWD_LOSS_RECOV· 457

INQA_INIT_ERROR· 457

INQA_INST_FAIL· 458

INQA_INTVL_DIFF· 458

INQA_MP_NOIF· 458

INQA_NO_RESOURCE· 459

INQA_NO_SUPPORT· 459

INQA_SMOOTH_BEGIN_FAIL· 459

INQA_SMOOTH_END_FAIL· 459

IP6ADDR·· 460

IP6ADDR_CREATEADDRESS_ERROR· 460

IP6ADDR_CREATEADDRESS_INVALID·· 460

IP6ADDR_FUNCTION_FAIL· 461

IP6FW··· 462

IPv6_MTU_SET_DRV_NOT_SUPPORT· 462

IPADDR messages· 463

IPADDR_HA_EVENT_ERROR· 463

IPADDR_HA_STOP_EVENT· 464

IPFW··· 465

IPFW_FAILURE· 465

IPFW_SETTING_FAILED_PACKETDROP· 465

IPv4_MTU_SET_DRV_NOT_SUPPORT· 466

IPSEC messages· 467

IPSEC_FAILED_ADD_FLOW_TABLE· 467

IPSEC_PACKET_DISCARDED·· 467

IPSEC_SA_ESTABLISH· 468

IPSEC_SA_ESTABLISH_FAIL· 468

IPSEC_SA_INITINATION· 469

IPSEC_SA_TERMINATE· 469

IPSG messages· 470

IPSG_ADDENTRY_ERROR· 470

IPSG_ADDEXCLUDEDVLAN_ERROR· 471

IPSG_ARP_LOCALMAC_CONFLICT· 471

IPSG_ARP_REMOTEMAC_CONFLICT· 472

IPSG_DELENTRY_ERROR· 472

IPSG_DELEXCLUDEDVLAN_ERROR· 473

IPSG_MAC_CONFLICT· 473

IPSG_ND_LOCALMAC_CONFLICT· 474

IPSG_ND_REMOTEMAC_CONFLICT· 474

IPSG_IPV4_ALARMCLEAR· 475

IPSG_IPV4_ALARMEMERGE· 475

IPSG_IPV6_ALARMCLEAR· 475

IPSG_IPV6_ALARMEMERGE· 476

IRDP messages· 477

IRDP_EXCEED_ADVADDR_LIMIT· 477

IRF· 478

IRF_LINK_BLOCK· 478

IRF_LINK_DOWN· 478

IRF_LINK_UP· 478

IRF_MEMBERID_CONFLICT· 479

IRF_MERGE· 479

IRF_MERGE_NEED_REBOOT· 479

IRF_MERGE_NOT_NEED_REBOOT· 480

ISIS messages· 481

ISIS_LSP_CONFLICT· 481

ISIS_MEM_ALERT· 481

ISIS_NBR_CHG·· 482

ISSU messages· 483

ISSU_LOAD_FAILED·· 483

ISSU_LOAD_SUCCESS· 483

ISSU_PROCESSWITCHOVER· 483

ISSU_ROLLBACKCHECKNORMAL· 484

L2PT messages· 485

L2PT_SET_MULTIMAC_FAILED·· 485

L2PT_CREATE_TUNNELGROUP_FAILED·· 485

L2PT_ADD_GROUPMEMBER_FAILED·· 485

L2PT_ENABLE_DROP_FAILED·· 486

L2TPv2 messages· 487

L2TPV2_TUNNEL_EXCEED_LIMIT· 487

L2TPV2_SESSION_EXCEED_LIMIT· 487

L2VPN messages· 488

L2VPN_ARP_MOBILITY_SUPPRESS (public instance) 488

L2VPN_ARP_MOBILITY_SUPPRESS (VPN instance) 488

L2VPN_ARP_MOBILITY_UNSUPPRESS (public instance) 489

L2VPN_ARP_MOBILITY_UNSUPPRESS (VPN instance) 489

L2VPN_MAC_MOBILITY_SUPPRESS· 490

L2VPN_MAC_MOBILITY_UNSUPPRESS· 490

L2VPN_BGPVC_CONFLICT_LOCAL· 491

L2VPN_BGPVC_CONFLICT_REMOTE· 491

L2VPN_HARD_RESOURCE_NOENOUGH· 491

L2VPN_HARD_RESOURCE_RESTORE· 492

L2VPN_LABEL_DUPLICATE· 492

L2VPN_MLAG_AC_CONFLICT· 493

PROCESS· 493

LAGG messages· 494

LAGG_ACTIVE· 494

LAGG_AUTO_AGGREGATION· 494

LAGG_INACTIVE_AICFG·· 495

LAGG_INACTIVE_BFD·· 495

LAGG_INACTIVE_CONFIGURATION· 496

LAGG_INACTIVE_DUPLEX· 496

LAGG_INACTIVE_HARDWAREVALUE· 497

LAGG_INACTIVE_IFCFG_DEFAULT· 497

LAGG_INACTIVE_IFCFG_LOOPPORT· 498

LAGG_INACTIVE_IFCFG_NONAGG·· 498

LAGG_INACTIVE_KEY_INVALID·· 499

LAGG_INACTIVE_LACP_ISOLATE· 499

LAGG_INACTIVE_LOWER_LIMIT· 500

LAGG_INACTIVE_NODEREMOVE· 500

LAGG_INACTIVE_OPERSTATE· 501

LAGG_INACTIVE_PARTNER· 501

LAGG_INACTIVE_PARTNER_KEY_WRONG·· 502

LAGG_INACTIVE_PARTNER_MAC_WRONG·· 502

LAGG_INACTIVE_PARTNER_NONAGG·· 503

LAGG_INACTIVE_PARTNER_RDIRHANDLE· 503

LAGG_INACTIVE_PHYSTATE· 504

LAGG_INACTIVE_PORT_DEFAULT· 504

LAGG_INACTIVE_RDIRHANDLE· 505

LAGG_INACTIVE_REDUNDANCY· 505

LAGG_INACTIVE_RESOURCE_INSUFICIE· 506

LAGG_INACTIVE_SPEED·· 506

LAGG_INACTIVE_STANDBY· 507

LAGG_INACTIVE_UPPER_LIMIT· 507

LAGG_SELECTPORT_INCONSISTENT· 508

LDP messages· 509

LDP_ADJACENCY_DOWN· 510

LDP_MPLSLSRID_CHG·· 511

LDP_SESSION_CHG·· 512

LDP_SESSION_GR· 513

LDP_SESSION_SP· 514

LIPC messages· 515

LIPC_CHECKDOWN· 515

LIPC_MTCP_CHECK· 515

LIPC_STCP_CHECK· 516

LIPC_SUDP_CHECK· 516

PORT_CHANGE· 517

LLDP messages· 518

LLDP_CREATE_NEIGHBOR· 518

LLDP_DELETE_NEIGHBOR· 519

LLDP_LESS_THAN_NEIGHBOR_LIMIT· 519

LLDP_NEIGHBOR_AGE_OUT· 520

LLDP_NEIGHBOR_PROTECTION_BLOCK· 520

LLDP_NEIGHBOR_PROTECTION_DOWN· 521

LLDP_NEIGHBOR_PROTECTION_UNBLOCK· 521

LLDP_NEIGHBOR_PROTECTION_UP· 521

LLDP_PVID_INCONSISTENT· 522

LLDP_REACH_NEIGHBOR_LIMIT· 522

LOAD messages· 523

BOARD_LOADING·· 523

LOAD_FAILED·· 523

LOAD_FINISHED·· 524

LOGIN messages· 525

LOGIN_FAILED·· 525

LOGIN_ INVALID_USERNAME_PWD·· 525

LPDT messages· 526

LPDT_LOOPED·· 526

LPDT_RECOVERED·· 526

LPDT_VLAN_LOOPED·· 526

LPDT_VLAN_RECOVERED·· 527

LPDT_VSI_LOOPED·· 527

LPDT_VSI_RECOVERED·· 527

LPDT_VSI_BLOCKFAIL· 528

LS messages· 529

LOCALSVR_PROMPTED_CHANGE_PWD·· 529

LS_ADD_USER_TO_GROUP· 529

LS_AUTHEN_FAILURE· 530

LS_AUTHEN_SUCCESS· 530

LS_DEL_USER_FROM_GROUP· 531

LS_DELETE_PASSWORD_FAIL· 531

LS_PWD_ADDBLACKLIST· 531

LS_PWD_CHGPWD_FOR_AGEDOUT· 532

LS_PWD_CHGPWD_FOR_AGEOUT· 532

LS_PWD_CHGPWD_FOR_COMPOSITION· 532

LS_PWD_CHGPWD_FOR_FIRSTLOGIN· 533

LS_PWD_CHGPWD_FOR_LENGTH· 533

LS_PWD_FAILED2WRITEPASS2FILE· 533

LS_PWD_MODIFY_FAIL· 534

LS_PWD_MODIFY_SUCCESS· 534

LS_REAUTHEN_FAILURE· 535

LS_UPDATE_PASSWORD_FAIL· 535

LS_USER_CANCEL· 535

LS_USER_PASSWORD_EXPIRE· 536

LS_USER_ROLE_CHANGE· 536

LSPV messages· 537

LSPV_PING_STATIS_INFO·· 537

MAC messages· 538

MAC_DRIVER_ADD_ENTRY· 538

MAC_NOTIFICATION· 539

MAC_PROTOCOLPKT_NORES_GLOBAL· 540

MAC_PROTOCOLPKT_NORES_PORT· 540

MAC_PROTOCOLPKT_NORES_VLAN· 541

MAC_TABLE_FULL_GLOBAL· 541

MAC_TABLE_FULL_PORT· 541

MAC_TABLE_FULL_VLAN· 542

MAC_VLAN_LEARNLIMIT_NORESOURCE· 542

MAC_VLAN_LEARNLIMIT_NOTSUPPORT· 542

MACA messages· 543

MACA_ENABLE_NOT_EFFECTIVE· 543

MACA_LOGIN_FAILURE· 544

MACA_LOGIN_FAILURE (EAD) 545

MACA_LOGIN_SUCC· 546

MACA_LOGIN_SUCC (in open mode) 546

MACA_LOGOFF· 547

MACA_LOGOFF (in open mode) 547

MACSEC messages· 548

MACSEC_MKA_KEEPALIVE_TIMEOUT· 548

MACSEC_MKA_PRINCIPAL_ACTOR· 548

MACSEC_MKA_SAK_REFRESH· 549

MACSEC_MKA_SESSION_REAUTH· 549

MACSEC_MKA_SESSION_SECURED·· 550

MACSEC_MKA_SESSION_START· 550

MACSEC_MKA_SESSION_STOP· 551

MACSEC_MKA_SESSION_UNSECURED·· 551

MBFD messages· 552

MBFD_TRACEROUTE_FAILURE· 552

MBUF messages· 553

MBUF_DATA_BLOCK_CREATE_FAIL· 553

MDC messages· 554

MDC_CREATE_ERR· 554

MDC_CREATE· 554

MDC_DELETE· 555

MDC_KERNEL_EVENT_TOOLONG·· 555

MDC_LICENSE_EXPIRE· 555

MDC_NO_FORMAL_LICENSE· 556

MDC_NO_LICENSE_EXIT· 556

MDC_OFFLINE· 556

MDC_ONLINE· 557

MDC_STATE_CHANGE· 557

MFIB messages· 558

MFIB_IPV6L3MULTICAST_FAIL· 558

MFIB_IPV6L3MULTICAST_FAIL_INT· 558

MFIB_IPV6L3MULTICAST_SUCCEED·· 559

MFIB_IPV6L3MULTICAST_SUCCEED_INT· 559

MFIB_L3MULTICAST_FAIL· 559

MFIB_L3MULTICAST_FAIL_INT· 560

MFIB_L3MULTICAST_SUCCEED·· 560

MFIB_L3MULTICAST_SUCCEED_INT· 560

MFIB_MEM_ALERT· 561

MFIB_MTI_NO_ENOUGH_RESOURCE· 561

MGROUP messages· 562

MGROUP_APPLY_SAMPLER_FAIL· 562

MGROUP_RESTORE_CPUCFG_FAIL· 562

MGROUP_RESTORE_GROUP_FAIL· 563

MGROUP_RESTORE_IFCFG_FAIL· 563

MGROUP_SYNC_CFG_FAIL· 564

MOD messages· 565

MOD_ENABLE_FAIL· 565

MOD_MODIFY_FAIL· 565

MPLS messages· 566

MPLS_HARD_RESOURCE_NOENOUGH· 566

MPLS_HARD_RESOURCE_RESTORE· 566

MTLK messages· 567

MTLK_UPLINK_STATUS_CHANGE· 567

MTP messages· 568

MTP_PING_INFO·· 568

MTP_TRACERT_INFO·· 568

NA4· 569

NA4_CLEARINFO_DRV· 569

NA4_GETINFO_DRV· 569

NA4_STATISTIC_DRV· 569

NAT messages· 570

NAT_ADDR_BIND_CONFLICT· 570

NAT_FAILED_ADD_FLOW_RULE· 570

NAT_FAILED_ADD_FLOW_TABLE· 571

NAT_FLOW·· 572

NAT_SERVER_INVALID·· 573

NAT_SERVICE_CARD_RECOVER_FAILURE· 574

ND messages· 575

ND_COMMONPROXY_ENABLE_FAILED·· 575

ND_CONFLICT· 575

ND_DUPADDR· 576

ND_ENTRY_ENOUGHRESOURCE· 576

ND_ENTRY_INCONSISTENT· 577

ND_ENTRY_NORESOURCE· 578

ND_HOST_IP_CONFLICT· 578

ND_LOCALPROXY_ENABLE_FAILED·· 579

ND_MAC_CHECK· 579

ND_NETWORKROUTE_DUPLICATE· 579

ND_RAGUARD_DROP· 580

ND_RATE_EXCEEDED·· 580

ND_RATELIMIT_NOTSUPPORT· 581

ND_SET_PORT_TRUST_NORESOURCE· 581

ND_SET_VLAN_REDIRECT_NORESOURCE· 581

ND_SNOOPING_LEARN_ALARM·· 582

ND_SNOOPING_LEARN_ALARM_RECOVER· 582

ND_USER_DUPLICATE_IPV6ADDR· 583

ND_USER_MOVE· 584

ND_USER_OFFLINE· 584

ND_USER_ONLINE· 585

NETCONF messages· 586

CLI 586

EDIT-CONFIG·· 587

EDIT_CONFIG_CLI 588

NETCONF_MSG_DEL· 588

THREAD·· 589

NQA messages· 590

NQA_ENTRY_PROBE_RESULT· 590

NQA_LOG_UNREACHABLE· 590

NQA_START_FAILURE· 591

NQA_TWAMP_LIGHT_PACKET_INVALID·· 591

NQA_TWAMP_LIGHT_REACTION· 592

NQA_TWAMP_LIGHT_START_FAILURE· 592

NSS messages· 593

NSS_ENABLE_FAIL· 593

NSS_SESSION_TIMEOUT_FAIL· 593

NTP messages· 594

NTP_CLOCK_CHANGE· 594

NTP_LEAP_CHANGE· 594

NTP_SOURCE_CHANGE· 595

NTP_SOURCE_LOST· 595

NTP_STRATUM_CHANGE· 595

OAP messages· 596

OAP_CLIENT_DEREG·· 596

OAP_CLIENT_TIMEOUT· 596

OBJP messages· 597

OBJP_ACCELERATE_NO_RES· 597

OBJP_ACCELERATE_NOT_SUPPORT· 597

OBJP_ACCELERATE_UNK_ERR· 598

OFP messages· 599

OFP_ACTIVE· 599

OFP_ACTIVE_FAILED·· 599

OFP_CONNECT· 599

OFP_FAIL_OPEN· 600

OFP_FLOW_ADD·· 600

OFP_FLOW_ADD_ARP_FAILED·· 601

OFP_FLOW_ADD_BUSY· 601

OFP_FLOW_ADD_BUSY_RECOVER· 601

OFP_FLOW_ADD_DUP· 602

OFP_FLOW_ADD_FAILED·· 602

OFP_FLOW_ADD_FAILED·· 603

OFP_FLOW_ADD_ND_FAILED·· 603

OFP_FLOW_ADD_TABLE_MISS· 604

OFP_FLOW_ADD_TABLE_MISS_FAILED·· 604

OFP_FLOW_DEL· 605

OFP_FLOW_DEL_L2VPN_DISABLE· 605

OFP_FLOW_DEL_TABLE_MISS· 606

OFP_FLOW_DEL_TABLE_MISS_FAILED·· 606

OFP_FLOW_DEL_VXLAN_DEL· 607

OFP_FLOW_MOD·· 607

OFP_FLOW_MOD_FAILED·· 608

OFP_FLOW_MOD_TABLE_MISS· 608

OFP_FLOW_MOD_TABLE_MISS_FAILED·· 609

OFP_FLOW_RMV_GROUP· 609

OFP_FLOW_RMV_HARDTIME· 609

OFP_FLOW_RMV_IDLETIME· 610

OFP_FLOW_RMV_METER· 610

OFP_FLOW_UPDATE_FAILED·· 611

OFP_GROUP_ADD·· 611

OFP_GROUP_ADD_FAILED·· 612

OFP_GROUP_DEL· 612

OFP_GROUP_MOD·· 613

OFP_GROUP_MOD_FAILED·· 613

OFP_GROUP_REFRESH_FAILED·· 614

OFP_GROUP_ROLLBACK_FAILED·· 614

OFP_METER_ADD·· 615

OFP_METER_ADD_FAILED·· 615

OFP_METER_DEL· 616

OFP_METER_MOD·· 616

OFP_METER_MOD_FAILED·· 617

OFP_MISS_RMV_GROUP· 617

OFP_MISS_RMV_HARDTIME· 617

OFP_MISS_RMV_IDLETIME· 618

OFP_MISS_RMV_METER· 618

OFP_SMARTGROUP_BIND·· 619

OFP_SMARTGROUP_BIND_FAILED·· 619

OFP_SMARTGROUP_NEW_BIND·· 620

OFP_SMARTGROUP_NEW_BIND_FAILED·· 620

OFP_SMARTGROUP_REBIND·· 621

OFP_SMARTGROUP_REBIND_FAILED·· 622

OFP_SMARTGROUP_UNBIND·· 622

OFP_SMARTGROUP_UNBIND_FAILED·· 623

OFP_TTP_GROUP_DEL_DENY· 623

OFP_RADARDETECTION· 624

PORT_MOD·· 625

OPENSRC (FreeRADIUS) messages· 626

HUP event 626

Process restart event 627

Process start event 627

User authentication· 628

OPTMOD messages· 631

BIAS_HIGH· 631

BIAS_LOW·· 631

BIAS_NORMAL· 632

CFG_ERR· 632

CHKSUM_ERR· 632

IO_ERR· 633

MOD_ALM_OFF· 633

MOD_ALM_ON· 633

MODULE_IN· 634

MODULE_OUT· 634

OPTMOD_COUNTERFEIT_MOUDULE· 634

OPTMOD_MODULE_CHECK· 635

PHONY_MODULE· 635

RX_ALM_OFF· 635

RX_ALM_ON· 636

RX_POW_HIGH· 636

RX_POW_LOW·· 636

RX_POW_NORMAL· 637

TEMP_HIGH· 637

TEMP_LOW·· 637

TEMP_NORMAL· 638

TX_ALM_OFF· 638

TX_ALM_ON· 638

TX_POW_HIGH· 639

TX_POW_LOW·· 639

TX_POW_NORMAL· 639

TYPE_ERR· 640

VOLT_HIGH· 640

VOLT_LOW·· 640

VOLT_NORMAL· 641

OSPF messages· 642

OSPF_DUP_RTRID_NBR· 642

OSPF_IP_CONFLICT_INTRA· 642

OSPF_LAST_NBR_DOWN· 643

OSPF_MEM_ALERT· 643

OSPF_NBR_CHG·· 644

OSPF_NBR_CHG_REASON· 645

OSPF_RT_LMT· 646

OSPF_RTRID_CHG·· 646

OSPF_RTRID_CONFLICT_INTER· 646

OSPF_RTRID_CONFLICT_INTRA· 647

OSPF_VLINKID_CHG·· 647

OSPFV3 messages· 648

OSPFV3_LAST_NBR_DOWN· 648

OSPFV3_MEM_ALERT· 648

OSPFV3_NBR_CHG·· 649

OSPFV3_RT_LMT· 649

PBB messages· 650

PBB_JOINAGG_WARNING·· 650

PBR messages· 651

PBR_HARDWARE_ERROR· 651

PCE messages· 652

PCE_PCEP_SESSION_CHG·· 652

PEX messages (IRF 3) 653

PEX_ASSOCIATEID_MISMATCHING·· 653

PEX_CONFIG_ERROR· 653

PEX_CONNECTION_ERROR· 654

PEX_FORBID_STACK· 654

PEX_LINK_BLOCK· 655

PEX_LINK_DOWN· 656

PEX_LINK_FORWARD·· 656

PEX_REG_JOININ· 657

PEX_REG_LEAVE· 657

PEX_REG_REQUEST· 658

PEX_STACKCONNECTION_ERROR· 658

PEX messages (IRF 3.1) 659

PEX_AUTOCONFIG_BAGG_ASSIGNMEMBER· 659

PEX_AUTOCONFIG_BAGG_CREATE· 659

PEX_AUTOCONFIG_BAGG_NORESOURCE· 660

PEX_AUTOCONFIG_BAGG_REMOVEMEMBER· 661

PEX_AUTOCONFIG_CAPABILITY_ENABLE· 661

PEX_AUTOCONFIG_CASCADELIMIT· 661

PEX_AUTOCONFIG_CONNECTION_ERROR· 662

PEX_AUTOCONFIG_DIFFGROUPNUMBER· 662

PEX_AUTOCONFIG_DYNAMICBAGG_STP· 663

PEX_AUTOCONFIG_GROUP_CREATE· 663

PEX_AUTOCONFIG_NONUMBERRESOURCE· 663

PEX_AUTOCONFIG_NOT_CASCADEPORT· 664

PEX_AUTOCONFIG_NUMBER_ASSIGN· 664

PEX_LLDP_DISCOVER· 665

PEX_MEMBERID_EXCEED·· 665

PEX_PECSP_OPEN_RCVD·· 665

PEX_PECSP_OPEN_SEND·· 666

PEX_PECSP_TIMEOUT· 666

PFILTER messages· 667

PFILTER_GLB_IPV4_DACT_NO_RES· 667

PFILTER_GLB_IPV4_DACT_UNK_ERR· 667

PFILTER_GLB_IPV6_DACT_NO_RES· 668

PFILTER_GLB_IPV6_DACT_UNK_ERR· 668

PFILTER_GLB_MAC_DACT_NO_RES· 669

PFILTER_GLB_MAC_DACT_UNK_ERR· 669

PFILTER_GLB_NO_RES· 670

PFILTER_GLB_NOT_SUPPORT· 670

PFILTER_GLB_ RES_CONFLICT· 671

PFILTER_GLB_UNK_ERR· 671

PFILTER_IF_IPV4_DACT_NO_RES· 672

PFILTER_IF_IPV4_DACT_UNK_ERR· 672

PFILTER_IF_IPV6_DACT_NO_RES· 673

PFILTER_IF_IPV6_DACT_UNK_ERR· 673

PFILTER_IF_MAC_DACT_NO_RES· 674

PFILTER_IF_MAC_DACT_UNK_ERR· 674

PFILTER_IF_NO_RES· 675

PFILTER_IF_NOT_SUPPORT· 675

PFILTER_IF_RES_CONFLICT· 676

PFILTER_IF_UNK_ERR· 676

PFILTER_IPV4_FLOW_INFO·· 677

PFILTER_IPV4_FLOW_STATIS· 677

PFILTER_IPV6_FLOW_INFO·· 678

PFILTER_IPV6_FLOW_STATIS· 678

PFILTER_IPV6_STATIS_INFO·· 679

PFILTER_MAC_FLOW_INFO·· 679

PFILTER_STATIS_INFO·· 680

PFILTER_VLAN_IPV4_DACT_NO_RES· 680

PFILTER_VLAN_IPV4_DACT_UNK_ERR· 681

PFILTER_VLAN_IPV6_DACT_NO_RES· 681

PFILTER_VLAN_IPV6_DACT_UNK_ERR· 682

PFILTER_VLAN_MAC_DACT_NO_RES· 682

PFILTER_VLAN_MAC_DACT_UNK_ERR· 683

PFILTER_VLAN_NO_RES· 683

PFILTER_VLAN_NOT_SUPPORT· 684

PFILTER_VLAN_RES_CONFLICT· 684

PFILTER_VLAN_UNK_ERR· 685

PIM messages· 686

PIM_NBR_DOWN· 686

PIM_NBR_UP· 686

PING messages· 687

PING_STATISTICS· 687

PING_VPN_STATISTICS· 688

PKG messages· 689

PKG_BOOTLOADER_FILE_FAILED·· 689

PKG_BOOTLOADER_FILE_SUCCESS· 689

PKG_INSTALL_ACTIVATE_FAILED·· 689

PKG_INSTALL_ACTIVATE_SUCCESS· 690

PKI messages· 691

GET_CERT_FROM_CA_SERVER_FAIL· 691

IMPORT_CERT_FAIL· 692

REQUEST_CERT_FAIL· 693

REQUEST_CERT_SUCCESS· 694

RETRIEVE_CRL_FAIL· 695

VALIDATE_CERT_FAIL· 696

PKT2CPU messages· 698

PKT2CPU_NO_RESOURCE· 698

PKTCPT· 699

PKTCPT_AP_OFFLINE· 699

PKTCPT_AREADY_EXIT· 699

PKTCPT_CONN_FAIL· 700

PKTCPT_INVALID_FILTER· 700

PKTCPT_LOGIN_DENIED·· 700

PKTCPT_MEMORY_ALERT· 701

PKTCPT_OPEN_FAIL· 701

PKTCPT_OPERATION_TIMEOUT· 701

PKTCPT_SERVICE_FAIL· 702

PKTCPT_UNKNOWN_ERROR· 702

PKTCPT_UPLOAD_ERROR· 703

PKTCPT_WRITE_FAIL· 703

PoE messages· 704

POE_AI_CLEAR· 704

POE_AI_DETECTIONMODE_NONE· 704

POE_AI_DETECTIONMODE_SIMPLE· 705

POE_AI_DISCONNECT_AC· 705

POE_AI_DISCONNECT_DELAY· 705

POE_AI_FORCE_PoE· 706

POE_AI_HIGH_INRUSH· 706

POE_AI_LEGACY· 706

POE_AI_MAXPOWER· 707

POE_AI_RESTART· 707

POE_TRACK_POWEROFF· 707

POE_TRACK_UNREACHABLE· 708

Portal messages· 709

PORTAL_RULE_FAILED·· 709

PORTSEC messages· 710

PORTSEC_ACL_FAILURE· 710

PORTSEC_CAR_FAILURE· 710

PORTSEC_CREATEAC_FAILURE· 711

PORTSEC_LEARNED_MACADDR· 711

PORTSEC_NTK_NOT_EFFECTIVE· 712

PORTSEC_PORTMODE_NOT_EFFECTIVE· 712

PORTSEC_PROFILE_FAILURE· 712

PORTSEC_URL_FAILURE· 713

PORTSEC_VIOLATION· 713

PORTSEC_VLANMACLIMIT· 714

PPP messages· 715

IPPOOL_ADDRESS_EXHAUSTED·· 715

PPP_USER_LOGON_SUCCESS· 715

PPP_USER_LOGON_FAILED·· 716

PPP_USER_LOGOFF· 716

PTP messages· 718

PTP_MASTER_CLOCK_CHANGE· 718

PTP_PKTLOST· 719

PTP_PKTLOST_RECOVER· 720

PTP_PORT_BMCINFO_CHANGE· 720

PTP_PORT_STATE_CHANGE· 721

PTP_SRC_CHANGE· 722

PTP_SRC_SWITCH· 723

PTP_TIME_LOCK· 723

PTP_TIME_NOT_LOCK· 724

PTS·· 725

PTS_AK_AUTH_FAILED·· 725

PTS_AK_INVALID·· 725

PTS_AK_NO_CERT· 725

PTS_AK_NO_EXIST· 726

PTS_AK_NO_LOAD·· 726

PTS_BTW_PCR_FAILED·· 726

PTS_CHECK_RM_VERSION_FAILED·· 727

PTS_CREATE_AGED_TIMER_FAILED·· 727

PTS_CREATE_CHECK_TIMER_FAILED·· 727

PTS_CREATE_CONTEXT_FAILED·· 728

PTS_CREATE_EPOLL_FAILED·· 728

PTS_CREATE_HASH_FAILED·· 728

PTS_CREATE_SELFVERIFY_COUNTER_FAILED·· 729

PTS_CREATE_SELFVERIFY_TIMER_FAILED·· 729

PTS_CREATE_SOCKET_FAILED·· 729

PTS_CREATE_TIMER_FAILED·· 730

PTS_FILE_HASH_FAILED·· 730

PTS_LOAD_KEY_FAILED·· 730

PTS_PARSE_IML_FAILED·· 731

PTS_PKG_PCR_FAILED·· 731

PTS_READ_PCR_FAILED·· 731

PTS_RM_FILE_FAILED·· 732

PTS_RUNTIME_PCR_FAILED·· 732

PTS_SELFVERIFY_FAILED·· 732

PTS_SELFVERIFY_START_FAILED·· 733

PTS_TEMPLATE_HASH_FAILED·· 733

PWDCTL messages· 734

PWDCTL_ADD_BLACKLIST· 734

PWDCTL_CHANGE_PASSWORD·· 734

PWDCTL_FAILED_TO_WRITEPWD·· 735

PWDCTL_FAILED_TO_OPENFILE· 735

PWDCTL_NOENOUGHSPACE· 735

PWDCTL_NOTFOUNDUSER· 736

PWDCTL_UPDATETIME· 736

QOS messages· 737

QOS_MIRROR_SYNC_CFG_FAIL· 737

QOS_CAR_APPLYUSER_FAIL· 737

QOS_CBWFQ_REMOVED·· 738

QOS_GTS_APPLYUSER_FAIL· 738

QOS_IFA_CONFIG_FAIL· 739

QOS_IFA_REFRESH_FAIL· 739

QOS_LR_APPLYIF_FAIL· 739

QOS_NOT_ENOUGH_BANDWIDTH· 740

QOS_NOT_ENOUGH_NNIBANDWIDTH· 740

QOS_POLICY_APPLYCOPP_CBFAIL· 741

QOS_POLICY_APPLYCOPP_FAIL· 741

QOS_POLICY_APPLYGLOBAL_CBFAIL· 742

QOS_POLICY_APPLYGLOBAL_FAIL· 742

QOS_POLICY_APPLYIF_CBFAIL· 743

QOS_POLICY_APPLYIF_FAIL· 743

QOS_POLICY_APPLYUSER_FAIL· 744

QOS_POLICY_APPLYVLAN_CBFAIL· 744

QOS_POLICY_APPLYVLAN_FAIL· 745

QOS_QMPROFILE_APPLYIF_FAIL· 745

QOS_QMPROFILE_APPLYUSER_FAIL· 746

QOS_QMPROFILE_MODIFYQUEUE_FAIL· 746

QOS_QUEUE_APPLYIF_FAIL· 747

QOS_UNI_RESTORE_FAIL· 747

QOS_WRED_TABLE_APPLYFABRIC_FAIL· 748

QOS_WRED_TABLE_CFG_FAIL· 748

RADIUS messages· 749

RADIUS_ACCT_SERVER_DOWN· 749

RADIUS_ACCT_SERVER_UP· 749

RADIUS_AUTH_FAILURE· 750

RADIUS_AUTH_SERVER_DOWN· 750

RADIUS_AUTH_SERVER_UP· 751

RADIUS_AUTH_SUCCESS· 751

RADIUS_REMOVE_SERVER_FAIL· 751

RDDC messages· 752

RDDC_ACTIVENODE_CHANGE· 752

RESMON·· 753

RESMON_MINOR· 753

RESMON_MINOR_RECOVERY· 754

RESMON_SEVERE· 754

RESMON_SEVERE_RECOVERY· 755

RESMON_USEDUP· 755

RESMON_USEDUP_RECOVERY· 756

RIP messages· 757

RIP_MEM_ALERT· 757

RIP_RT_LMT· 757

RIPNG messages· 758

RIPNG_MEM_ALERT· 758

RIPNG_RT_LMT· 758

RM messages· 759

RM_ACRT_REACH_LIMIT· 759

RM_ACRT_REACH_THRESVALUE· 759

RM_THRESHLD_VALUE_REACH· 760

RM_TOTAL_THRESHLD_VALUE_REACH· 760

RPR messages· 761

RPR_EXCEED_MAX_SEC_MAC· 761

RPR_EXCEED_MAX_SEC_MAC_OVER· 761

RPR_EXCEED_MAX_STATION· 762

RPR_EXCEED_MAX_STATION_OVER· 762

RPR_EXCEED_RESERVED_RATE· 762

RPR_EXCEED_RESERVED_RATE_OVER· 763

RPR_IP_DUPLICATE· 763

RPR_IP_DUPLICATE_OVER· 763

RPR_JUMBO_INCONSISTENT· 764

RPR_JUMBO_INCONSISTENT_OVER· 764

RPR_LAGGCONFIG_INCONSISTENT· 764

RPR_LAGGCONFIG_INCONSISTENT_OVER· 765

RPR_MISCABLING·· 765

RPR_MISCABLING_OVER· 765

RPR_PROTECTION_INCONSISTENT· 766

RPR_PROTECTION_INCONSISTENT_OVER· 766

RPR_SEC_MAC_DUPLICATE· 766

RPR_SEC_MAC_DUPLICATE_OVER· 767

RPR_TOPOLOGY_INCONSISTENT· 767

RPR_TOPOLOGY_INCONSISTENT_OVER· 767

RPR_TOPOLOGY_INSTABILITY· 768

RPR_TOPOLOGY_INSTABILITY_OVER· 768

RPR_TOPOLOGY_INVALID·· 768

RPR_TOPOLOGY_INVALID_OVER· 769

RRPP messages· 770

RRPP_IPP_CHECK· 770

RRPP_RING_FAIL· 770

RRPP_RING_RESTORE· 770

RTM messages· 771

RTM_EMAIL_SUCCESS· 771

RTM_EMAIL_FAILED·· 771

RTM_ENVIRONMENT· 772

RTM_TCL_LOAD_FAILED·· 772

RTM_TCL_MODIFY· 772

RTM_TCL_NOT_EXIST· 773

SAVA messages· 774

SAVA_SET_DRV_FAILED·· 774

SAVA_SPOOFING_DETECTED·· 774

SAVI messages· 775

SAVI_FILTER_ENTRY_ADD·· 775

SAVI_FILTER_ENTRY_DEL· 775

SAVI_SPOOFING_DETECTED·· 776

SCMD messages· 777

PROCESS_ABNORMAL· 777

PROCESS_ACTIVEFAILED·· 778

PROCESS_CORERECORD·· 778

SCM_ABNORMAL_REBOOT· 779

SCM_ABNORMAL_REBOOTMDC· 779

SCM_ABORT_RESTORE· 780

SCM_INSMOD_ADDON_TOOLONG·· 780

SCM_KERNEL_INIT_TOOLONG·· 780

SCM_KILL_PROCESS· 781

SCM_PROCESS_HEALTHY· 781

SCM_PROCESS_UNHEALTHY· 782

SCM_PROCESS_STARTING_TOOLONG·· 782

SCM_PROCESS_STILL_STARTING·· 783

SCM_SKIP_PROCESS· 783

SCRLSP messages· 785

SCRLSP_LABEL_DUPLICATE· 785

SESSION messages· 786

SESSION_IPV4_FLOW·· 787

SESSION_IPV6_FLOW·· 788

SFLOW messages· 790

SFLOW_HARDWARE_ERROR· 790

SHELL messages· 791

SHELL_CMD·· 791

SHELL_CMD_CONFIRM·· 791

SHELL_CMD_EXECUTEFAIL· 792

SHELL_CMD_INPUT· 792

SHELL_CMD_INPUT_TIMEOUT· 792

SHELL_CMD_INVALID_CHARACTER· 793

SHELL_CMD_MATCHFAIL· 793

SHELL_CMDDENY· 794

SHELL_CMDFAIL· 794

SHELL_COMMIT· 794

SHELL_COMMIT_DELAY· 795

SHELL_COMMIT_REDELAY· 795

SHELL_COMMIT_ROLLBACK· 795

SHELL_COMMIT_ROLLBACKDONE· 796

SHELL_COMMIT_WILLROLLBACK· 796

SHELL_CRITICAL_CMDFAIL· 796

SHELL_LOGIN· 797

SHELL_LOGOUT· 797

SLSP messages· 798

SLSP_LABEL_DUPLICATE· 798

SMARTMC messages· 799

ERROR· 799

SMLK messages· 800

SMLK_LINK_INACTIVE· 800

SMLK_LINK_SWITCH· 800

SNMP messages· 801

SNMP_ACL_RESTRICTION· 801

SNMP_AUTHENTICATION_FAILURE· 801

SNMP_GET· 802

SNMP_INFORM_LOST· 802

SNMP_NOTIFY· 803

SNMP_SET· 804

SNMP_USM_NOTINTIMEWINDOW·· 804

SOCKET messages· 805

SOCKET_TCP_UNREAD·· 805

SSHC messages· 806

SSHC_ALGORITHM_MISMATCH· 806

SSHC_AUTH_PASSWORD_FAIL· 806

SSHC_AUTH_PUBLICKEY_FAIL· 807

SSHC_CERT_VERIFY_FAIL· 808

SSHC_CONNECT_FAIL· 809

SSHC_DECRYPT_FAIL· 809

SSHC_DISCONNECT· 810

SSHC_ENCRYPT_FAIL· 810

SSHC_HOST_NAME_ERROR· 810

SSHC_KEY_EXCHANGE_FAIL· 811

SSHC_MAC_ERROR· 811

SSHC_PUBLICKEY_NOT_EXIST· 811

SSHC_VERSION_MISMATCH· 812

SSHS messages· 813

SSHS_ACL_DENY· 813

SSHS_ALGORITHM_MISMATCH· 813

SSHS_AUTH_EXCEED_RETRY_TIMES· 814

SSHS_AUTH_FAIL· 814

SSHS_AUTH_KBDINT_FAIL· 815

SSHS_AUTH_PWD_FAIL· 815

SSHS_AUTH_TIMEOUT· 815

SSHS_AUTH_SUCCESS· 816

SSHS_AUTHOR_FAIL· 816

SSHS_CERT_VERIFY_FAIL· 817

SSHS_CONNECT· 818

SSHS_DECRYPT_FAIL· 818

SSHS_DISCONNECT· 819

SSHS_ENCRYPT_FAIL· 819

SSHS_LOG·· 820

SSHS_MAC_ERROR· 820

SSHS_REACH_SESSION_LIMIT· 821

SSHS_REACH_USER_LIMIT· 821

SSHS_SCP_OPER· 821

SSHS_SFTP_OPER· 822

SSHS_SRV_UNAVAILABLE· 822

SSHS_VERSION_MISMATCH· 823

STAMGR messages· 824

STAMGR_ADD_FAILVLAN· 824

STAMGR_ADDBAC_INFO·· 824

STAMGR_ADDSTA_INFO·· 824

STAMGR_AUTHORACL_FAILURE· 825

STAMGR_AUTHORUSERPROFILE_FAILURE· 825

STAMGR_CLIENT_OFFLINE· 826

STAMGR_CLIENT_ONLINE· 826

STAMGR_DELBAC_INFO·· 826

STAMGR_DELSTA_INFO·· 827

STAMGR_DOT1X_LOGIN_FAILURE· 827

STAMGR_DOT1X_LOGIN_SUCC· 828

STAMGR_DOT1X_LOGOFF· 828

STAMGR_MACA_LOGIN_FAILURE· 829

STAMGR_MACA_LOGIN_SUCC· 830

STAMGR_MACA_LOGOFF· 830

STAMGR_STAIPCHANGE_INFO·· 831

STAMGR_TRIGGER_IP· 831

STM messages· 832

STM_AUTO_UPDATE_FAILED·· 832

STM_AUTO_UPDATE_FINISHED·· 833

STM_AUTO_UPDATING·· 833

STM_HELLOPKT_NOTSEND·· 834

STM_HELLOPKT_NOTRCV· 834

STM_LINK_DOWN· 834

STM_LINK_TIMEOUT· 835

STM_LINK_UP· 835

STM_MERGE· 835

STM_MERGE_NEED_REBOOT· 836

STM_MERGE_NOT_NEED_REBOOT· 836

STM_PHY_DOWN· 836

STM_PHY_UP· 837

STM_SAMEMAC· 837

STM_SOMER_CHECK· 837

STP messages· 838

STP_BPDU_PROTECTION· 838

STP_BPDU_RECEIVE_EXPIRY· 838

STP_CONSISTENCY_CHECK· 839

STP_CONSISTENCY_RESTORATION· 839

STP_DETECTED_TC· 839

STP_DISABLE· 840

STP_DISCARDING·· 840

STP_DISPUTE· 841

STP_DISPUTE_RESTORATION· 841

STP_EDGEPORT_INACTIVE· 842

STP_ENABLE· 842

STP_FORWARDING·· 842

STP_LOOP_PROTECTION· 843

STP_LOOPBACK_PROTECTION· 843

STP_NOT_ROOT· 843

STP_NOTIFIED_TC· 844

STP_PORT_TYPE_INCONSISTENCY· 844

STP_PVID_INCONSISTENCY· 844

STP_PVST_BPDU_PROTECTION· 845

STP_ROOT_PROTECTION· 845

STP_STG_NUM_DETECTION· 845

SYSLOG messages· 847

SYSLOG_LOGBUFFER_FAILURE· 847

SYSLOG_LOGFILE_CREATE· 847

SYSLOG_LOGFILE_FULL· 847

SYSLOG_LOGFILE_OVERWRITE· 848

SYSLOG_NO_SPACE· 848

SYSLOG_RESTART· 848

SYSLOG_RTM_EVENT_BUFFER_FULL· 849

TACACS messages· 850

TACACS_ACCT_SERVER_DOWN· 850

TACACS_ACCT_SERVER_UP· 850

TACACS_AUTH_FAILURE· 851

TACACS_AUTH_SERVER_DOWN· 851

TACACS_AUTH_SERVER_UP· 852

TACACS_AUTH_SUCCESS· 852

TACACS_AUTHOR_SERVER_DOWN· 853

TACACS_AUTHOR_SERVER_UP· 853

TACACS_REMOVE_SERVER_FAIL· 854

TCSM·· 855

TCSM_CERT_BROKEN· 855

TCSM_KEY_BROKEN· 855

TCSM_KEY_HIERARCHY_BROKEN· 856

TCSM_TSS_SVC_DOWN· 856

TCSM_TSS_SVC_UP· 856

TELNETD messages· 857

TELNETD_ACL_DENY· 857

TELNETD_REACH_SESSION_LIMIT· 857

TRACK messages· 858

TRACK_STATE_CHANGE· 858

TRILL messages· 859

TRILL_DUP_SYSTEMID·· 859

TRILL_INTF_CAPABILITY· 859

TRILL_LICENSE_EXPIRED·· 860

TRILL_LICENSE_EXPIRED_TIME· 860

TRILL_LICENSE_UNAVAILABLE· 860

TRILL_MEM_ALERT· 861

TRILL_NBR_CHG·· 861

Telemetry stream messages· 862

TELEMETRY_STREAM_ENCAP_FAIL· 862

USBDPY·· 863

USBDPY_START· 863

USBDPY_SUCCEEDED·· 863

USBDPY_FAILED·· 863

USBDPY_DPY· 864

VCF messages· 865

VCF_AGGR_CREAT· 865

VCF_AGGR_DELETE· 865

VCF_AGGR_FAILED·· 866

VCF_AUTO_ANALYZE_USERDEF· 866

VCF_AUTO_NO_USERDEF· 867

VCF_AUTO_START· 867

VCF_AUTO_STATIC_CMD·· 868

VCF_BGP· 869

VCF_DOWN_LINK· 870

VCF_DRIVER_INIT· 870

VCF_FAILED_ADD_IRFPORT· 871

VCF_GET_IMAGE· 871

VCF_GET_TEMPLATE· 872

VCF_INSTALL_IMAGE· 872

VCF_IRF_FINISH· 873

VCF_IRF_FOUND·· 873

VCF_IRF_START· 874

VCF_LOOPBACK_START· 874

VCF_LOOPBACK_START_FAILED·· 875

VCF_LOOPBACK_ALLOC· 875

VCF_LOOPBACK_NO_FREE_IP· 876

VCF_LOOPBACK_RECLAIM·· 876

VCF_REBOOT· 877

VCF_SKIP_INSTALL· 877

VCF_STATIC_CMD_ERROR· 878

VCF_UP_LINK· 878

VCF_UPDATE_COPY_FAILED·· 879

VCF_UPDATE_FAILED·· 879

VCF_WHITE_LIST_CHECK· 880

VLAN messages· 881

VLAN_CREATEFAIL· 881

VLAN_FAILED·· 881

VLAN_QINQETHTYPE_FAILED·· 882

VLAN_VLANMAPPING_FAILED·· 882

VLAN_VLANTRANSPARENT_FAILED·· 883

VRRP messages· 884

VRRP_STATUS_CHANGE· 884

VRRP_VF_STATUS_CHANGE· 885

VRRP_VMAC_INEFFECTIVE· 885

VSRP messages· 886

VSRP_BIND_FAILED·· 886

VXLAN messages· 887

VXLAN_LICENSE_UNAVAILABLE· 887

WEB messages· 888

LOGIN· 888

LOGIN_FAILED·· 888

LOGOUT· 888

WEBAUTH messages· 889

WEBAUTH_USER_LOGON_SUCCESS· 889

WIPS messages· 890

APFLOOD·· 890

AP_CHANNEL_CHANGE· 890

ASSOCIATEOVERFLOW·· 890

HONEYPOT· 891

HTGREENMODE· 891

MAN_IN_MIDDLE· 891

WIPS_DOS· 892

WIPS_FLOOD·· 892

WIPS_MALF· 893

WIPS_SPOOF· 894

WIPS_WEAKIV· 894

WIRELESSBRIDGE· 895

 


Introduction

This document includes the following system messages:

·     Messages specific to Release 66xx of the switch.

·     Messages for the Comware 7 software platform version based on which Release 66xx was produced. Some platform system messages might not be available on the switch.

This document is intended only for managing H3C Fixed-Port Switches Do not use this document for any other device models.

This document assumes that the readers are familiar with data communications technologies and H3C networking products.

System log message format

By default, the system log messages use one of the following formats depending on the output destination:

·     Log host:

<PRI>TIMESTAMP Sysname %%vendorMODULE/severity/MNEMONIC: location; CONTENT

·     Destinations except for the log host:

Prefix TIMESTAMP Sysname MODULE/severity/MNEMONIC: CONTENT

 

 

NOTE:

Log message examples in this document use the format for destinations except the log host. They do not contain elements available only for the log host, including the location element.

 

Table 1 System log message elements

Element

Description

<PRI>

Priority identifier. This element is contained only in messages sent to the log host.

It is calculated by using the following formula:

Priority identifier=facilityx8+severity

Where:

·     Facility is specified by using the info-center loghost command. A log host uses this parameter to identify log sources and filter log messages.

·     Severity represents the importance of the message. For more information about severity levels, see Table 2.

Prefix

Message type identifier. This element is contained in the system log messages sent to non-log-host destinations.

The element uses the following symbols to indicate message severity:

·     Percentage sign (%)—Informational and higher levels.

·     Asterisk (*)—Debug level.

TIMESTAMP

Date and time when the event occurred.

The following are commands for configuring the timestamp format:

·     Log host—Use the info-center timestamp loghost command.

·     Non-log-host destinations—Use the info-center timestamp command.

Sysname

Name or IP address of the device that generated the message.

%%vendor

Manufacturer flag. This element is %%10 for H3C.

This element is only available in messages sent to the log host.

MODULE

Name of the module that produced the message.

severity

Severity level of the message. (For more information about severity levels, see Table 2.)

MNEMONIC

Text string that uniquely identifies the system message. The maximum length is 32 characters.

location

Optional. This element identifies where the message occurred. This element is contained only in messages sent to the log host.

This element presents location information for the message in the following format:

-attribute1=x-attribute2=y…-attributeN=z

The following are examples of location attributes:

·     -MDC=XX, which represents the MDC on which the message occurred.

·     -DevIp=XXX.XXX.XXX.XXX, which represents the source IP of the message.

·     -Slot=XX, which represents the slot on which the message occurred.

·     -Chassis=XX-Slot=XX, which represents the chassis and slot on which the message occurred.

This element is separated from the message description by using a semicolon (;).

CONTENT

Text string that contains detailed information about the event or error.

For variable fields in this element, this document uses the representations in Table 3.

 

System log messages are classified into eight severity levels from 0 to 7. The lower the number, the higher the severity, as shown in Table 2.

Table 2 System log message severity levels

Level

Severity

Description

0

Emergency

The system is unusable. For example, the system authorization has expired.

1

Alert

Action must be taken immediately. For example, traffic on an interface exceeds the upper limit.

2

Critical

Critical condition. For example, the device temperature exceeds the upper limit, the power module fails, or the fan tray fails.

3

Error

Error condition. For example, the link state changes or a storage card is unplugged.

4

Warning

Warning condition. For example, an interface is disconnected, or the memory resources are used up.

5

Notification

Normal but significant condition. For example, a terminal logs in to the device, or the device reboots.

6

Informational

Informational message. For example, a command or a ping operation is executed.

7

Debug

Debugging message.

 

For variable fields in the message text, this document uses the representations in Table 3. The values are case insensitive, even though the representations are uppercase letters.

Table 3 Variable field representations

Representation

Information type

INT16

Signed 16-bit decimal number.

UINT16

Unsigned 16-bit decimal number.

INT32

Signed 32-bit decimal number.

UINT32

Unsigned 32-bit decimal number.

INT64

Signed 64-bit decimal number.

UINT64

Unsigned 64-bit decimal number.

DOUBLE

Two dot-separated signed 32-bit decimal numbers. The format is [INTEGER].[INTEGER].

HEX

Hexadecimal number.

CHAR

Single character.

STRING

Character string.

IPADDR

IP address.

MAC

MAC address.

DATE

Date.

TIME

Time.

 

Managing and obtaining system log messages

You can manage system log messages by using the information center.

By default, the information center is enabled. Log messages can be output to the console, monitor terminal, log buffer, log host, and log file.

To filter log messages, use the info-center source command to specify log output rules. A log output rule specifies the source modules and the lowest severity level of log messages that can be output to a destination. A log message is output if its severity level is higher than or equal to the specified level. For example, if you specify a severity level of 6 (informational), log messages that have a severity level from 0 to 6 are output.

For more information about using the information center, see the network management and monitoring configuration guide for the product.

Obtaining log messages from the console terminal

Access the device through the console port. Real-time log messages are displayed on the console terminal.

Obtaining log messages from a monitor terminal

Monitor terminals refer to terminals that access the device through the AUX, VTY, or TTY lines (for example, Telnet). To obtain log messages from a monitor terminal, use the following guidelines:

·     To display log messages on the monitor terminal, you must configure the terminal monitor command.

·     For monitor terminals, the lowest level of log messages that can be displayed is determined by both the terminal logging level and info-center source commands.

 

 

NOTE:

Settings for the terminal monitor and terminal logging level commands take effect only on the current login session. The default settings for the commands restore at a relogin.

 

Obtaining log messages from the log buffer

Use the display logbuffer command to display history log messages in the log buffer.

Obtaining log messages from the log file

By default, the log file feature automatically saves logs from the log file buffer to the log file every 24 hours. You can use the info-center logfile frequency command to change the automatic saving internal.

To manually save logs to the log file, use the logfile save command. The log file buffer is cleared each time a save operation is performed.

By default, you can obtain the log file from the flash:/logfile path.

To view the contents of the log file on the device, use the more command.

Obtaining log messages from a log host

Use the info-center loghost command to specify the service port number and IP address of a log host. To specify multiple log hosts, repeat the command.

For a successful log message transmission, make sure the specified port number is the same as the port number used on the log host. The default service port number is 514.

Software module list

Table 4 lists all software modules that might produce system log messages. This document uses "OPENSRC" to represent all open source modules.

Table 4 Software module list

Module name representation

Module name expansion

AAA

Authentication, Authorization and Accounting

ACL

Access Control List

ANCP

Access Node Control Protocol

APMGR

Access Point Management

ARP

Address Resolution Protocol

ATK

Attack Detection and Prevention

ATM

Asynchronous Transfer Mode

BFD

Bidirectional Forwarding Detection

BGP

Border Gateway Protocol

BLS

Blacklist

CFD

Connectivity Fault Detection

CFGMAN

Configuration Management

CONNLMT

Connection Limit

DEV

Device Management

DHCP

Dynamic Host Configuration Protocol

DHCPR

IPv4 DHCP Relay

DHCPS

DHCP Server

DHCPS6

DHCPv6 Server

DHCPSP4

DHCP Snooping

DHCPSP6

DHCPv6 Snooping

DIAG

Diagnosis

DLDP

Device Link Detection Protocol

DOT1X

802.1X

DRNI

Distributed Resilient Network Interconnect

DRVPLAT

Drive Platform

EDEV

Extended-Device Management

ERPS

Ethernet Ring Protection Switching

ETH

Ethernet

ETHDRNI

Ethernet Distributed Resilient Network Interconnect

ETHOAM

Ethernet Operation, Administration and Maintenance

EVB

Edge Virtual Bridging

EVIISIS

Ethernet Virtual Interconnect Intermediate System-to-Intermediate System

FCOE

Fibre Channel Over Ethernet

FCLINK

Fibre Channel Link

FCZONE

Fibre Channel Zone

FIB

Forwarding Information Base

FILTER

Filter

FIPSNG

FIP Snooping

FS

File System

FTP

File Transfer Protocol

gRPC

Google Remote Procedure Call

HA

High Availability

HQOS

Hierarchical QoS

HTTPD

Hypertext Transfer Protocol Daemon

HLTH

Health

IFNET

Interface Net Management

IKE

Internet Key Exchange

IMA

Integrity Measurements Architecture

iNQA

Intelligent Network Quality Analyzer

iNOF

Intelligent Lossless NVMe Over Fabric

IP6ADDR

IPv6 Addressing

IP6FW

IPv6 Forwarding

IPADDR

IP Addressing

IPFW

IP Forwarding

IPSEC

IP Security

IPSG

IP Source Guard

IRDP

ICMP Router Discovery Protocol

IRF

Intelligent Resilient Framework

ISIS

Intermediate System-to-Intermediate System

ISSU

In-Service Software Upgrade

L2PT

Layer 2 Protocol Tunneling

L2TPV2

Layer 2 Tunneling Protocol Version 2

L2VPN

Layer 2 VPN

LAGG

Link Aggregation

LDP

Label Distribution Protocol

LLDP

Link Layer Discovery Protocol

LIPC

Leopard Inter-process Communication

LOAD

Load Management

LOGIN

Login

LPDT

Loopback Detection

LS

Local Server

LSPV

LSP Verification

MAC

Media Access Control

MACA

MAC Authentication

MACSEC

MAC Security

MBFD

MPLS BFD

MBUF

Memory buffer

MDC

Multitenant Device Context

MFIB

Multicast Forwarding Information Base

MGROUP

Mirroring group

MPLS

Multiprotocol Label Switching

MTLK

Monitor Link

NAT

Network Address Translation

NA4

IPv4 NetAnalysis

NETCONF

Network Configuration Protocol

ND

Neighbor Discovery

NQA

Network Quality Analyzer

NSS

Session-based NetStream

NTP

Network Time Protocol

OAP

Open Application Platform

OPENSRC (FreeRADIUS)

Open Source

OBJP

Object Policy

OFP

OpenFlow Protocol

OPTMOD

Optical Module

OSPF

Open Shortest Path First

OSPFV3

Open Shortest Path First Version 3

PFILTER

Packet Filter

PBB

Provider Backbone Bridge

PBR

Policy-Based Routing

PCE

Path Computation Element

PEX

Port Extender

PIM

Protocol Independent Multicast

PING

Packet Internet Groper

PKG

Package

PKI

Public Key Infrastructure

PKT2CPU

Packet to CPU

PKTCPT

Packet Capture

PoE

Power over Ethernet

PORTAL

Portal

PORTSEC

Port Security

PPP

Point to Point Protocol

PTP

Precision Time Protocol

PTS

Platform Trust Services

PWDCTL

Password Control

QOS

Quality of Service

RADIUS

Remote Authentication Dial In User Service

RESMON

Resource Monitor

RDDC

Redundancy

RIP

Routing Information Protocol

RIPNG

Routing Information Protocol Next Generation

RM

Routing Management

RPR

Resilient Packet Ring

RRPP

Rapid Ring Protection Protocol

RTM

Real-Time Event Manager

SCMD

Service Control Manager Daemon

SCRLSP

Static CRLSP

SESSION

Session

SFLOW

Sampler Flow

SHELL

Shell

SLSP

Static LSP

SMARTMC

Smart Management Center

SMLK

Smart Link

SNMP

Simple Network Management Protocol

SSHC

Secure Shell Client

SSHS

Secure Shell Server

STAMGR

Station Management

STM

Stack Topology Management

STP

Spanning Tree Protocol

SYSEVENT

System Event

SYSLOG

System Log

TACACS

Terminal Access Controller Access Control System

TCSM

Trusted Computing Services Management

TELNETD

Telnet Daemon

TRILL

Transparent Interconnect of Lots of Links

TSTREAM

Telemetry Stream

VCF

Vertical Converged Framework

VLAN

Virtual Local Area Network

VRRP

Virtual Router Redundancy Protocol

VSRP

Virtual Service Redundancy Protocol

VXLAN

Virtual eXtensible LAN

WEB

Web

WEBAUTH

Web Authentication

WIPS

Wireless Intrusion Prevention System

 

Using this document

This document categorizes system log messages by software module. The modules are ordered alphabetically. Except for OPENSRC, the system log messages for each module are listed in alphabetic order of their mnemonic names. The OPENSRC messages are unordered because they use the same mnemonic name (SYSLOG). For each OPENSRC message, the section title uses a short description instead of the mnemonic name.

This document explains messages in tables. Table 5 describes information provided in these tables.

Table 5 Message explanation table contents

Item

Content

Example

Message text

Presents the message description.

ACL [UINT32] [STRING] [UINT64] packet(s).

Variable fields

Briefly describes the variable fields in the order that they appear in the message text.

The variable fields are numbered in the "$Number" form to help you identify their location in the message text.

$1: ACL number.

$2: ID and content of an ACL rule.

$3: Number of packets that matched the rule.

Severity level

Provides the severity level of the message.

6

Example

Provides a real message example. The examples do not include the "<PRI>TIMESTAMP Sysname %%vendor" part or the "Prefix TIMESTAMP Sysname" part, because information in this part varies with system settings.

ACL/6/ACL_STATIS_INFO: ACL 2000 rule 0 permit source 1.1.1.1 0 logging 10000 packet(s).

Explanation

Explains the message, including the event or error cause.

Number of packets that matched an ACL rule. This message is sent when the packet counter changes.

Recommended action

Provides recommended actions. For informational messages, no action is required.

No action is required.

 


AAA messages

This section contains AAA messages.

AAA_FAILURE

Message text

-AAAType=[STRING]-AAADomain=[STRING]-Service=[STRING]-UserName=[STRING]; AAA failed.

Variable fields

$1: AAA type.

$2: AAA scheme.

$3: Service.

$4: Username.

Severity level

5

Example

AAA/5/AAA_FAILURE: -AAAType=AUTHOR-AAADomain=domain1-Service=login-UserName=cwf@system; AAA failed.

Explanation

An AAA request was rejected.

The following are the common reasons:

·     No response was received from the server.

·     The username or password was incorrect.

·     The service type that the user applied for was incorrect.

Recommended action

1.     Verify that the device is correctly connected to the server.

2.     Enter the correct username and password.

3.     Verify that the server settings are the same as the settings on the device.

4.     If the problem persists, contact H3C Support.

 

AAA_LAUNCH

Message text

-AAAType=[STRING]-AAADomain=[STRING]-Service=[STRING]-UserName=[STRING]; AAA launched.

Variable fields

$1: AAA type.

$2: AAA scheme.

$3: Service.

$4: Username.

Severity level

6

Example

AAA/6/AAA_LAUNCH: -AAAType=AUTHEN-AAADomain=domain1-Service=login-UserName=cwf@system; AAA launched.

Explanation

An AAA request was received.

Recommended action

No action is required.

 

AAA_SUCCESS

Message text

-AAAType=[STRING]-AAADomain=[STRING]-Service=[STRING]-UserName=[STRING]; AAA succeeded.

Variable fields

$1: AAA type.

$2: AAA scheme.

$3: Service.

$4: Username.

Severity level

6

Example

AAA/6/AAA_SUCCESS: -AAAType=AUTHOR-AAADomain=domain1-Service=login-UserName=cwf@system; AAA succeeded.

Explanation

An AAA request was accepted.

Recommended action

No action is required.

 


ACL messages

This section contains ACL messages.

ACL_ACCELERATE_NO_RES

Message text

Failed to accelerate [STRING] ACL [UINT32]. The resources are insufficient.

Variable fields

$1: ACL type.

$2: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NO_RES: Failed to accelerate IPv6 ACL 2001. The resources are insufficient.

Explanation

Hardware resources were insufficient for accelerating an ACL.

Recommended action

Delete some rules or disabled ACL acceleration for other ACLs to release hardware resources.

 

ACL_ACCELERATE_NONCONTIGUOUSMASK

Message text

Failed to accelerate ACL [UINT32]. ACL acceleration supports only contiguous wildcard masks.

Variable fields

$1: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NONCONTIGUOUSMASK: Failed to accelerate ACL 2001. ACL acceleration supports only contiguous wildcard masks.

Explanation

ACL acceleration failed because rules containing noncontiguous wildcard masks exist in the ACL.

Recommended action

Check the ACL rules and delete the unsupported configuration.

 

ACL_ACCELERATE_NOT_SUPPORT

Message text

Failed to accelerate [STRING] ACL [UINT32]. The operation is not supported.

Variable fields

$1: ACL type.

$2: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NOT_SUPPORT: Failed to accelerate IPv6 ACL 2001. The operation is not supported.

Explanation

ACL acceleration failed because the system does not support ACL acceleration.

Recommended action

No action is required.

 

ACL_ACCELERATE_NOT_SUPPORTHOPBYHOP

Message text

Failed to accelerate IPv6 ACL [UINT32]. ACL acceleration does not support the rules that contain the hop-by-hop keywords.

Variable fields

$1: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NOT_SUPPORTHOPBYHOP: Failed to accelerate IPv6 ACL 2001. ACL acceleration does not support the rules that contain the hop-by-hop keywords.

Explanation

ACL acceleration failed for the IPv6 ACL because rules containing the hop-by-hop keyword exist in the ACL.

Recommended action

Check the ACL rules and delete the unsupported configuration.

 

ACL_ACCELERATE_NOT_SUPPORTMULTITCPFLAG

Message text

Failed to accelerate IPv6 ACL [UINT32]. ACL acceleration does not support specifying multiple TCP flags in one rule.

Variable fields

$1: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NOT_SUPPORTMULTITCPFLAG: Failed to accelerate IPv6 ACL 2001. ACL acceleration does not support specifying multiple TCP flags in one rule.

Explanation

ACL acceleration failed for the IPv6 ACL because rules containing multiple TCP flags exist in the ACL.

Recommended action

Check the ACL rules and delete the unsupported configuration.

 

ACL_ACCELERATE_UNK_ERR

Message text

Failed to accelerate [STRING] ACL [UINT32].

Variable fields

$1: ACL type.

$2: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_UNK_ERR: Failed to accelerate IPv6 ACL 2001.

Explanation

ACL acceleration failed because of an unknown error.

Recommended action

No action is required.

 

ACL_IPV6_STATIS_INFO

Message text

IPv6 ACL [UINT32] [STRING] [UINT64] packet(s).

Variable fields

$1: ACL number.

$2: ID and content of an IPv6 ACL rule.

$3: Number of packets that matched the rule.

Severity level

6

Example

ACL/6/ACL_IPV6_STATIS_INFO: IPv6 ACL 2000 rule 0 permit source 1:1::/64 logging 1000 packet(s).

Explanation

The number of packets matching the IPv6 ACL rule changed.

Recommended action

No action is required.

 

ACL_NO_MEM

Message text

Failed to configure [STRING] ACL [UINT] due to lack of memory.

Variable fields

$1: ACL type.

$2: ACL number.

Severity level

3

Example

ACL/3/ACL_NO_MEM: Failed to configure ACL 2001 due to lack of memory.

Explanation

Configuring the ACL failed because memory is insufficient.

Recommended action

Use the display memory-threshold command to check the memory usage.

 

ACL_STATIS_INFO

Message text

ACL [UINT32] [STRING] [UINT64] packet(s).

Variable fields

$1: ACL number.

$2: ID and content of an IPv4 ACL rule.

$3: Number of packets that matched the rule.

Severity level

6

Example

ACL/6/ACL_STATIS_INFO: ACL 2000 rule 0 permit source 1.1.1.1 0 logging 10000 packet(s).

Explanation

The number of packets matching the IPv4 ACL rule changed.

Recommended action

No action is required.

 

 


ANCP messages

This section contains ANCP messages.

ANCP_INVALID_PACKET

Message text

-NeighborName=[STRING]-State=[STRING]-MessageType=[STRING]; The [STRING] value [STRING] is wrong, and the value [STRING] is expected.

Variable fields

$1: ANCP neighbor name.

$2: Neighbor state.

$3: Message type.

$4: Field.

$5: Wrong value of the field.

$6: Expected value of the field.

Severity level

6

Example

ANCP/6/ANCP_INVALID_PACKET: -NeighborName=Dslam-State=SYNSENT-MessageType=SYNACK; The Sender Instance value 0 is wrong, and the value 1 is expected.

Explanation

The system received an adjacency message that had a field with a wrong value.

Recommended action

No action is required.

 

 


APMGR messages

This section contains access point management messages.

APMGR_AC_MEM_ALERT

Message text

The memory utilization has reached the threshold.

Variable fields

N/A

Severity level

4

Example

APMGR/4/APMGR_AC_MEM_ALERT: The memory utilization has reached the threshold.

Explanation

The AP failed to come online because the memory utilization exceeded the limit.

Recommended action

Stop creating manual APs and prevent APs from coming online.

 

APMGR_ADD_AP_FAIL

Message text

AP [STRING] failed to come online using serial ID [STRING]: MAC address [STRING] is being used by AP [STRING].

Variable fields

$1: AP name.

$2: Serial ID.

$3: MAC address.

$4: AP name.

Severity level

4

Example

APMGR/4/ APMGR_ADD_AP_FAIL: AP ap1 failed to come online using serial ID 01247ef96: MAC address 0023-7961-5201 is being used by AP ap2.

Explanation

The AP failed to come online because a manual AP that has the same MAC address already exists on the AC.

Recommended action

Delete either the manual AP that has the MAC address or the serial ID.

 

APMGR_ADDBAC_INFO

Message text

Add BAS AC [STRING].

Variable fields

$1: MAC address of the BAS AC.

Severity level

6

Example

APMGR/6/APMGR_ADDBAC_INFO: Add BAS AC 3ce5-a616-28cd.

Explanation

The BAS AC was connected to the master AC.

Recommended action

No action is required.

 

APMGR_AP_OFFLINE

Message text

AP [STRING] went offline. State changed to Idle.

Variable fields

$1: AP name.

Severity level

6

Example

APMGR/6/APMGR_AP_OFFLINE: AP ap1 went offline. State changed to Idle.

Explanation

The AP went offline. The state of the AP changed to Idle.

Recommended action

If the AP went offline abnormally, check the debugging information to locate the issue and resolve it.

 

APMGR_AP_ONLINE

Message text

AP [STRING] went online. State changed to Run.

Variable fields

$1: AP name.

Severity level

6

Example

APMGR/6/APMGR_AP_ONLINE: AP ap1 went online. State changed to Run.

Explanation

The AP came online. The state of the AP changed to Run.

Recommended action

No action is required.

 

APMGR_CWC_IMG_DOWNLOAD_COMPLETE

Message text

System software image file [STRING] downloading through the CAPWAP tunnel to AC [STRING] completed.

Variable fields

$1: Image file name.

$2: AC IP address.

Severity level

6

Example

APMGR/6/APMGR_CWC_IMG_DOWNLOAD_COMPLETE: System software image file 5800.ipe downloading through the CAPWAP tunnel to AC 192.168.10.1 completed.

Explanation

The AP downloaded the image file from the AC successfully.

Recommended action

No action is required.

 

APMGR_CWC_IMG_DOWNLOAD_START

Message text

Started to download the system software image file [STRING] through the CAPWAP tunnel to AC [STRING].

Variable fields

$1: Image file name.

$2: AC IP address.

Severity level

6

Example

APMGR/6/APMGR_CWC_IMG_DOWNLOAD_START: Started to download the system software image file 5800.ipe through the CAPWAP tunnel to AC 192.168.10.1.

Explanation

The AP started to download the image file from the AC.

Recommended action

Make sure the AP is correctly connected to the AC.

 

APMGR_CWC_IMG_NO_ENOUGH_SPACE

Message text

Insufficient flash memory space for downloading system software image file [STRING].

Variable fields

$1: Image file name.

Severity level

6

Example

APMGR/6/APMGR_CWC_IMG_NO_ENOUGH_SPACE: Insufficient flash memory space for downloading system software image file 5800.ipe.

Explanation

The AP failed to download the image file from the AC because of insufficient flash memory.

Recommended action

Delete files not in use from the AP.

 

APMGR_CWC_LOCAL_AC_DOWN

Message text

CAPWAP tunnel to Central AC [STRING] went down. Reason: [STRING].

Variable fields

$1: IP address of the central AC.

$2: Reason:

·     Added local AC IP address.

·     Deleted local AC IP address.

·     Local AC interface used for CAPWAP tunnel went down.

·     Local AC config changed.

·     N/A

Severity level

4

Example

APMGR/4/APMGR_CWC_LOCAL_AC_DOWN: CAPWAP tunnel to Central AC 2.2.2.1 went down. Reason: Added local AC IP address.

Explanation

The CAPWAP tunnel between the central AC and the local AC was terminated for a specific reason.

Recommended action

To resolve the issue:

1.     Examine the network connection between the central AC and the local AC.

2.     Verify that the central AC is correctly configured.

3.     Verify that the local AC is correctly configured.

4.     If the issue persists, contact H3C Support.

 

APMGR_CWC_LOCAL_AC_UP

Message text

CAPWAP tunnel to Central AC [STRING] went up.

Variable fields

$1: IP address of the central AC.

Severity level

6

Example

APMGR/6/APMGR_CWC_LOCAL_AC_UP: CAPWAP tunnel to Central AC 2.2.2.1 went up.

Explanation

The central AC has established a CAPWAP tunnel with the local AC.

Recommended action

No action is required.

 

APMGR_CWC_REBOOT

Message text

AP in state [STRING] is rebooting. Reason: [STRING]

Variable fields

$1: AP state.

$2: Reason:

·     AP was reset.

·     Image was downloaded successfully.

·     AP stayed in idle state for a long time.

Severity level

6

Example

APMGR/6/APMGR_CWC_REBOOT: AP in State Run is rebooting. Reason: AP was reset.

Explanation

The AP rebooted for a specific reason.

Recommended action

No action is required.

 

APMGR_CWC_RUN_DOWNLOAD_COMPLETE

Message text

File [STRING] successfully downloaded through the CAPWAP tunnel to AC [STRING].

Variable fields

$1: File name.

$2: AC IP address.

Severity level

6

Example

APMGR/6/APMGR_CWC_RUN_DOWNLOAD_COMPLETE: File ac.cfg successfully downloaded through the CAPWAP tunnel to AC 192.168.10.1.

Explanation

The AP downloaded the file from the AC successfully.

Recommended action

No action is required.

 

APMGR_CWC_RUN_DOWNLOAD_START

Message text

Started to download the file [STRING] through the CAPWAP tunnel to AC [STRING].

Variable fields

$1: File name.

$2: AC IP address.

Severity level

6

Example

APMGR/6/APMGR_CWC_RUN_DOWNLOAD_START: Started to download the file ac.cfg through the CAPWAP tunnel to AC 192.168.10.1.

Explanation

The AP started to download the file from the AC.

Recommended action

Make sure the AP is correctly connected to the AC.

 

APMGR_CWC_RUN_NO_ENOUGH_SPACE

Message text

Insufficient flash memory space for downloading file [STRING].

Variable fields

$1: File name.

Severity level

6

Example

APMGR/6/APMGR_CWC_RUN_NO_ENOUGH_SPACE: Insufficient flash memory space for downloading file ac.cfg.

Explanation

The AP failed to download the file from the AC because of insufficient flash memory.

Recommended action

Delete files not in use from the AP.

 

APMGR_CWC_TUNNEL_DOWN

Message text

CAPWAP tunnel to AC [STRING] went down. Reason: [STRING].

Variable fields

$1: AC IP address.

$2: Reason:

·     Added AP IP address.

·     Deleted AP IP address.

·     AP interface used for CAPWAP tunnel went down.

·     AP config changed.

·     AP was reset.

·     Number of echo retransmission attempts exceeded the limit.

·     Full retransmission queue.

·     Data channel timer expired.

·     Backup AC IP address changed.

·     Backup tunnel changed to master tunnel.

·     Failed to change backup tunnel to master tunnel.

·     Backup method changed.

·     N/A.

Severity level

6

Example

APMGR/6/APMGR_CWC_TUNNEL_DOWN: CAPWAP tunnel to AC 192.168.10.1 went down. Reason: AP was reset.

Explanation

The CAPWAP tunnel between the AP and the AC was terminated for a specific reason.

Recommended action

Examine the network connection between the AP and the AC.

 

APMGR_CWC_TUNNEL_UP

Message text

[STRING] CAPWAP tunnel to AC [STRING] went up.

Variable fields

$1: Tunnel type:

·     Master.

·     Backup.

$2: AC IP address.

Severity level

6

Example

APMGR/6/APMGR_CWC_TUNNEL_UP: Master CAPWAP tunnel to AC 192.168.10.1 went up.

Explanation

The AP was connected to the AC successfully and entered Run state.

Recommended action

No action is required.

 

APMGR_CWS_IMG_DOWNLOAD_COMPLETE

Message text

System software image file [STRING] downloading through the CAPWAP tunnel for AP [STRING] completed.

Variable fields

$1: Image file name.

$2: AP name.

Severity level

6

Example

APMGR/6/APMGR_ CWS_IMG_DOWNLOAD_COMPLETE: System software image file 5800.ipe downloading through the CAPWAP tunnel for AP ap2 completed.

Explanation

The AP downloaded the image file from the AC successfully.

Recommended action

No action is required.

 

APMGR_CWS_IMG_DOWNLOAD_START

Message text

AP [STRING] started to download the system software image file [STRING].

Variable fields

$1: AP name.

$2: Image file name.

Severity level

6

Example

APMGR/6/APMGR_CWS_IMG_DOWNLOAD_START: AP ap1 started to download the system software image file 5800.ipe.

Explanation

The AP started to download the image file from the AC.

Recommended action

No action is required.

 

APMGR_CWS_LOCAL_AC_DOWN

Message text

CAPWAP tunnel to local AC [STRING] went down. Reason: [STRING].

Variable fields

$1: IP address of the local AC.

$2: Reason:

·     Neighbor dead timer expired.

·     Local AC was deleted.

·     Serial number changed.

·     Processed join request in Run state.

·     Failed to retransmit message.

·     N/A

Severity level

4

Example

APMGR/4/APMGR_CWS_LOCAL_AC_DOWN: CAPWAP tunnel to local AC 1.1.1.1 went down. Reason: Serial number changed.

Explanation

The CAPWAP tunnel between the central AC and the local AC was terminated for a specific reason.

Recommended action

To resolve the issue:

·     Examine the network connection between the central AC and the local AC.

·     Verify that the central AC is correctly configured.

·     Verify that the local AC is correctly configured.

·     If the issue persists, contact H3C Support.

 

APMGR_CWS_LOCAL_AC_UP

Message text

CAPWAP tunnel to local AC [STRING] went up.

Variable fields

$1: IP address of the local AC.

Severity level

6

Example

APMGR/6/APMGR_CWS_LOCAL_AC_UP: CAPWAP tunnel to local AC 1.1.1.1 went up.

Explanation

The central AC has established a CAPWAP tunnel with the local AC.

Recommended action

No action is required.

 

APMGR_CWS_RUN_DOWNLOAD_COMPLETE

Message text

File [STRING] successfully downloaded through the CAPWAP tunnel for AP [STRING].

Variable fields

$1: File name.

$2: AP name.

Severity level

6

Example

APMGR/6/APMGR_CWS_RUN_DOWNLOAD_COMPLETE: File ac.cfg successfully downloaded through the CAPWAP tunnel for AP ap2.

Explanation

The AP downloaded the file from the AC successfully.

Recommended action

No action is required.

 

APMGR_CWS_RUN_DOWNLOAD_START

Message text

AP [STRING] started to download the file [STRING].

Variable fields

$1: AP name.

$2: File name.

Severity level

6

Example

APMGR/6/APMGR_CWS_RUN_DOWNLOAD_START: AP ap1 started to download the file ac.cfg.

Explanation

The AP started to download the file from the AC.

Recommended action

No action is required.

 

APMGR_CWS_TUNNEL_DOWN

Message text

CAPWAP tunnel to AP [STRING] went down. Reason: [STRING].

Variable fields

$1: AP name.

$2: Reason:

·     Neighbor dead timer expired.

·     AP was reset.

·     AP was deleted.

·     Serial number changed.

·     Processed join request in Run state.

·     Failed to retransmit message.

·     Received WTP tunnel down event from AP.

·     Backup AC closed the backup tunnel.

·     Tunnel switched.

·     N/A.

Severity level

6

Example

APMGR/6/APMGR_CWS_TUNNEL_DOWN: CAPWAP tunnel to AP ap1 went down. Reason: AP was reset.

Explanation

The AP went offline for a specific reason.

Recommended action

To resolve the issue:

1.     Examine the network connection between the AP and the AC.

2.     Verify that the AP is correctly configured.

3.     Verify that the AC is correctly configured.

4.     If the issue persists, contact H3C Support.

 

APMGR_CWS_TUNNEL_UP

Message text

[STRING] CAPWAP tunnel to AP [STRING] went up.

Variable fields

$1: Tunnel type:

·     Master.

·     Backup.

$2: AP name.

Severity level

6

Example

APMGR/6/APMGR_CWS_TUNNEL_UP: Backup CAPWAP tunnel to AP ap1 went up.

Explanation

The AP came online and entered Run state.

Recommended action

No action is required.

 

APMGR_DELBAC_INFO

Message text

Delete BAS AC [STRING].

Variable fields

$1: MAC address of the BAS AC.

Severity level

6

Example

APMGR/6/APMGR_DELBAC_INFO: Delete BAS AC 3ce5-a616-28cd.

Explanation

The BAS AC was disconnected from the master AC.

Recommended action

No action is required.

 

APMGR_LOCAL_AC_OFFLINE

Message text

Local AC [STRING] went offline. State changed to Idle.

Variable fields

$1: Name of the local AC.

Severity level

6

Example

APMGR/6/APMGR_LOCAL_AC_OFFLINE: Local AC ac1 went offline. State changed to Idle.

Explanation

The local AC went offline. The state of the local AC changed to Idle.

Recommended action

1.     If the local AC went offline abnormally, check the debugging information to locate the issue and resolve it.

2.     If the issue persists, contact H3C Support.

 

APMGR_LOCAL_AC_ONLINE

Message text

Local AC [STRING] went online. State changed to Run.

Variable fields

$1: Name of the local AC.

Severity level

6

Example

APMGR/6/APMGR_LOCAL_AC_ONLINE: Local AC ac1 went online. State changed to Run.

Explanation

The local AC came online. The state of the local AC changed to Run.

Recommended action

No action is required.

 

 

 


ARP messages

This section contains ARP messages.

ARP_ACTIVE_ACK_NO_REPLY

Message text

No ARP reply from IP [STRING] was received on interface [STRING].

Variable fields

$1: IP address.

$2: Interface name.

Severity level

6

Example

ARP/6/ARP_ACTIVE_ACK_NO_REPLY: No ARP reply from IP 192.168.10.1 was received on interface GigabitEthernet1/0/1.

Explanation

The ARP active acknowledgement feature did not receive an ARP reply after it sent an ARP request to the sender IP of an ARP message.

This message indicates the risk of attacks.

Recommended action

1.     Verify that the learned ARP entries on the device are consistent with the existing legal devices. When gateways and servers are on the network, check the ARP entries for these devices first.

2.     If the ARP entries are correct and the attack continues, contact H3C Support.

 

ARP_ACTIVE_ACK_NOREQUESTED_REPLY

Message text

Interface [STRING] received from IP [STRING] an ARP reply that was not requested by the device.

Variable fields

$1: Interface name.

$2: IP address.

Severity level

6

Example

ARP/6/ARP_ACTIVE_ACK_NOREQUESTED_REPLY: Interface GigabitEthernet1/0/1 received from IP 192.168.10.1 an ARP reply that was not requested by the device.

Explanation

The ARP active acknowledgement feature received an unsolicited ARP reply from a sender IP.

This message indicates the risk of attacks.

Recommended action

No action is required. The device discards the ARP reply automatically.

 

ARP_BINDRULETOHW_FAILED

Message text

Failed to download binding rule to hardware on the interface [STRING], SrcIP [IPADDR], SrcMAC [MAC], VLAN [UINT16], Gateway MAC [MAC].

Variable fields

$1: Interface name.

$2: Source IP address.

$3: Source MAC address.

$4: VLAN ID.

$5: Gateway MAC address.

Severity level

5

Example

ARP/5/ARP_BINDRULETOHW_FAILED: Failed to download binding rule to hardware on the interface GigabitEthernet1/0/1, SrcIP 1.1.1.132, SrcMAC 0015-E944-A947, VLAN 1, Gateway MAC 00A1-B812-1108.

Explanation

The system failed to set a binding rule to the hardware on an interface. The message is sent in any of the following situations:

·     The resources are not sufficient for the operation.

·     The memory is not sufficient for the operation.

·     A hardware error occurs.

Recommended action

To resolve the problem:

1.     Execute the display qos-acl resource command to check if the ACL resources for the operation are sufficient.

¡     If yes, proceed to step 2.

¡     If no, delete unnecessary configuration to release ACL resources. If no configuration can be deleted, proceed to step 2.

2.     Execute the display memory command to check if the memory for the operation is sufficient.

¡     If yes, proceed to step 3.

¡     If no, delete unnecessary configuration to release memory. If no configuration can be deleted, proceed to step 3.

3.     Delete the configuration and perform the operation again.

 

ARP_DETECTION_LOG

Message text

Detected an ARP attack on interface [STRING]: IP [STRING], MAC [STRING], VLAN [STRING]. [UINT32] packet(s) dropped.

Variable fields

$1: Interface name.

$2: IP address.

$3: MAC address.

$4: VLAN ID.

$5: Number of dropped packets.

Severity level

5

Example

ARP/5/ARP_INSPECTION: -MDC=1; Detected an ARP attack on interface GigabitEthernet1/0/1: IP 1.1.1.1, MAC 1-1-1, VLAN 100. 2 packet(s) dropped.

Explanation

An ARP attack was detected on an interface and attack packets were dropped.

Recommended action

Check the source of the ARP attack.

 

ARP_DUPLICATE_IPADDR_DETECT

Message text

Detected an IP address conflict. The device with MAC address [STRING] connected to interface [STRING] in VSI [STRING] and the device with MAC address [STRING] connected to interface [STRING] in VSI [STRING] were using the same IP address [IPADDR].

Variable fields

$1: MAC address.

$2: Interface name. (The interface can be a tunnel interface, Layer 3 interface, or Ethernet service instance.)

$3: VSI name.

$4: MAC address.

$5: Interface name. (The interface can be a tunnel interface, Layer 3 interface, or Ethernet service instance.)

$6: VSI name.

$7: Conflicting IP address.

Severity level

4

Example

ARP/4/ARP_DUPLICATE_IPADDR_DETECT: Detected an IP address conflict. The device with MAC address 00-00-01 connected to interface GigabitEthernet1/0/1 service-instance 1000 in VSI vpna and the device with MAC address 00-00-02 connected to interface tunnel 10 in VSI vpna were using the same IP address 192.168.1.1.

Explanation

This message is sent when an interface receives an ARP message in which the sender information conflicts with an existing ARP entry. The sender IP address is the same as the IP address in the entry, but the MAC addresses are different.

Recommended action

Change the IP address on either of the two devices.

 

ARP_DYNAMIC

Message text

The maximum number of dynamic ARP entries for the device reached.

Variable fields

N/A

Severity level

6

Example

ARP/6/ARP_DYNAMIC: The maximum number of dynamic ARP entries for the device reached.

Explanation

The maximum number of dynamic ARP entries for the device was reached.

Recommended action

No action is required.

 

ARP_DYNAMIC_IF

Message text

The maximum number of dynamic ARP entries for interface [STRING] reached.

Variable fields

$1: Interface name.

Severity level

6

Example

ARP/6/ARP_DYNAMIC_IF: The maximum number of dynamic ARP entries for interface GigabitEthernet1/0/1 reached.

Explanation

The maximum number of dynamic ARP entries for the specified interface was reached.

Recommended action

No action is required.

 

ARP_DYNAMIC_SLOT

Message text

Pattern 1:

The maximum number of dynamic ARP entries for slot [INT32] reached.

Pattern 2:

The maximum number of dynamic ARP entries for chassis [INT32] slot [INT32] reached.

Variable fields

Pattern 1:

$1: Slot number.

Pattern 2:

$1: Chassis number.

$2: Slot number.

Severity level

6

Example

ARP/6/ARP_DYNAMIC_SLOT: The maximum number of dynamic ARP entries for slot 2 reached.

Explanation

Pattern 1:

The maximum number of dynamic ARP entries for the slot was reached.

Pattern 2:

The maximum number of dynamic ARP entries for the slot on the chassis was reached.

Recommended action

No action is required.

 

ARP_ENTRY_CONFLICT

Message text

The software entry for [STRING] on [STRING] and the hardware entry did not have the same [STRING].

Variable fields

$1: IP address.

$2: VPN instance name. If the ARP entry belongs to the public network, this field displays the public network.

$3: Inconsistent items:

¡     MAC address.

¡     output interface.

¡     output port.

¡     outermost layer VLAN ID.

¡     second outermost layer VLAN ID.

¡     VSI index.

¡     link ID.

Severity level

6

Example

ARP/6/ARP_ENTRY_CONFLICT: The software entry for 1.1.1.1 on the VPN a and the hardware entry did not have the same MAC address, output port, VSI index, and link ID.

ARP/6/ARP_ENTRY_CONFLICT: The software entry for 1.1.1.2 on the public network and the hardware entry did not have the same MAC address, output port, VSI index, and link ID.

Explanation

The software entry for the specified IP address is not the same as the hardware entry. For example, they do not have the same output interface.

Recommended action

No action is required. ARP automatically refreshes the hardware entries.

 

ARP_ENTRY_ENOUGHRESOURCE

Message text

Issued the software entry to the driver for IPv4 address [STRING] on VPN instance [STRING].

Issued the software entry to the driver for IPv4 address [STRING] on the public network.

Variable fields

$1: IPv4 address.

$2: VPN instance name. If the ARP entry belongs to the public network, this field is not displayed.

Severity level

6

Example

ARP/6/ARP_ENTRY_ENOUGHRESOURCE: Issued the software entry to the driver for IPv4 address 10.1.1.1 on VPN instance vpn_1.

ARP/6/ARP_ENTRY_ENOUGHRESOURCE: Issued the software entry to the driver for IPv4 address 10.1.1.2 on the public network.

Explanation

After ARP entry consistency check is enabled by using the arp consistency-check enable command, a log is output when ARP successfully refreshes hardware entries according to software entries.

Recommended action

No action is required.

 

ARP_ENTRY_INCONSISTENT

Message text

Inconsistent software and hardware ARP entries for IPv4 address [STRING] on VPN instance [STRING]. Inconsistent parameters: [STRING].

Inconsistent software and hardware ARP entries for IPv4 address [STRING] on the public network. Inconsistent parameters: [STRING].

Variable fields

$1: IPv4 address.

$2: VPN instance name. If the ARP entry belongs to the public network, this field is not displayed.

$3: Inconsistent items:

¡     MAC address.

¡     output interface.

¡     output port.

¡     outermost layer VLAN ID.

¡     second outermost layer VLAN ID.

¡     VSI index.

¡     link ID.

Severity level

6

Example

ARP/6/ARP_ENTRY_INCONSISTENT: Inconsistent software and hardware ARP entries for IPv4 address 10.1.1.1 on VPN instance vpn_1. Inconsistent parameters: MAC address, output port, VSI index, and link ID.

ARP/6/ARP_ENTRY_INCONSISTENT: Inconsistent software and hardware ARP entries for IPv4 address 10.1.1.2 on the public network. Inconsistent parameters: MAC address, output port, VSI index, and link ID.

Explanation

After ARP entry consistency check is enabled by using the arp consistency-check enable command, a log is output when the device detects an inconsistency between software and hardware entries (for example, inconsistent output interface).

Recommended action

No action is required. ARP automatically refreshes the hardware entries.

 

ARP_ENTRY_NORESOURCE

Message text

Not enough hardware resources to issue the software entry to the driver for IPv4 address [STRING] on VPN instance [STRING].

Not enough hardware resources to issue the software entry to the driver for IPv4 address [STRING] on the public network.

Variable fields

$1: IPv4 address.

$2: VPN instance name. If the ARP entry belongs to the public network, this field is not displayed.

Severity level

6

Example

ARP/6/ARP_ENTRY_NORESOURCE: Not enough hardware resources to issue the software entry to the driver for IPv4 address 10.1.1.1 on  VPN instance vpn_1.

ARP/6/ARP_ENTRY_NORESOURCE: Not enough hardware resources to issue the software entry to the driver for IPv4 address 10.1.1.2 on the public network.

Explanation

After ARP entry consistency check is enabled by using the arp consistency-check enable command, a log is output when the device does not have sufficient hardware resources to deploy software entries to the driver.

Recommended action

No action is required. ARP automatically refreshes the hardware entries.

ARP_HOST_IP_CONFLICT

Message text

The host [STRING] connected to interface [STRING] cannot communicate correctly, because it uses the same IP address as the host connected to interface [STRING].

Variable fields

$1: IP address.

$2: Interface name.

$3: Interface name.

Severity level

4

Example

ARP/4/ARP_HOST_IP_CONFLICT: The host 1.1.1.1 connected to interface GigabitEthernet1/0/1 cannot communicate correctly, because it uses the same IP address as the host connected to interface GigabitEthernet1/0/2.

Explanation

The sender IP address in a received ARP message conflicted with the IP address of a host connected to another interface.

Recommended action

Check whether the hosts that send the ARP messages are legitimate. Disconnect the illegal host from the network.

 

ARP_LOCALPROXY_ENABLE_FAILED

Message text

Failed to enable local proxy ARP on interface [STRING].

Variable fields

$1: Interface name.

Severity level

4

Example

ARP/4/ARP_LOCALPROXY_ENABLE_FAILED: -MDC=1-Slot=2; Failed to enable local proxy ARP on interface VSI-interface 1.

Explanation

This message is sent when the device fails to enable local proxy ARP on an interface in a slot. If the interface resides on the MPU, the slot number is 0.

Recommended action

1.     Verify that the card supports local proxy ARP.

2.     Verify that sufficient hardware resources are available.

 

ARP_PKTQUE_ALERT

Message text

The current size of the ARP_PKT queue has reached [UINT32]. Please check the network environment.

Variable fields

$1: ARP packet queue size.

Severity level

6

Example

ARP/6/ARP_PKTQUE_ALERT: The current size of ARP_PKT queue has reached 4096. Please check the network environment.

Explanation

The system outputs a log every 60 seconds when the size of ARP packet queue exceeds 4 KB.

Recommended action

Verify that the sources of illegitimate packets.

 

ARP_RATE_EXCEEDED

Message text

The ARP packet rate ([UINT32] pps) exceeded the rate limit ([UINT32] pps) on interface [STRING] in the last [UINT32] seconds.

Variable fields

$1: ARP packet rate.

$2: ARP limit rate.

$3: Interface name.

$4: Interval time.

Severity level

4

Example

ARP/4/ARP_RATE_EXCEEDED: The ARP packet rate (100 pps) exceeded the rate limit (80 pps) on interface GigabitEthernet1/0/1 in the last 10 seconds.

Explanation

An interface received ARP messages at a higher rate than the rate limit.

Recommended action

Verify that the hosts at the sender IP addresses are legitimate.

 

ARP_RATELIMIT_NOTSUPPORT

Message text

Pattern 1:

ARP packet rate limit is not support on slot [INT32].

Pattern 2:

ARP packet rate limit is not support on chassis [INT32] slot [INT32].

Variable fields

Pattern 1:

$1: Slot number.

Pattern 2:

$1: Chassis number.

$2: Slot number.

Severity level

6

Example

ARP/6/ARP_RATELIMIT_NOTSUPPORT: ARP packet rate limit is not support on slot 2.

Explanation

Pattern 1:

ARP packet rate limit is not supported on the slot.

Pattern 2:

ARP packet rate limit is not supported on the slot of the chassis was reached.

Recommended action

Verify that the host at the sender IP address is legitimate.

 

ARP_SENDER_IP_INVALID

Message text

Sender IP [STRING] was not on the same network as the receiving interface [STRING].

Variable fields

$1: IP address.

$2: Interface name.

Severity level

6

Example

ARP/6/ARP_SENDER_IP_INVALID: Sender IP 192.168.10.2 was not on the same network as the receiving interface GigabitEthernet1/0/1.

Explanation

The sender IP of a received ARP message was not on the same network as the receiving interface.

Recommended action

Verify that the host at the sender IP address is legitimate.

 

ARP_SENDER_MAC_INVALID

Message text

Sender MAC [STRING] was not identical to Ethernet source MAC [STRING] on interface [STRING].

Variable fields

$1: MAC address.

$2: MAC address.

$3: Interface name.

Severity level

6

Example

ARP/6/ARP_SENDER_MAC_INVALID: Sender MAC 0000-5E14-0E00 was not identical to Ethernet source MAC 0000-5C14-0E00 on interface GigabitEthernet1/0/1.

Explanation

An interface received an ARP message. The sender MAC address in the message body was not identical to the source MAC address in the Ethernet header.

Recommended action

Verify that the host at the sender MAC address is legitimate.

 

ARP_SENDER_SMACCONFLICT

Message text

Packet was discarded because its sender MAC address was the MAC address of the receiving interface.

Interface: [STRING], sender IP: [STRING], target IP: [STRING].

Variable fields

$1: Interface name.

$2: Sender IP address.

$3: Target IP address.

Severity level

6

Example

ARP/6/ ARP_SENDER_SMACCONFLICT: Packet discarded for the sender MAC address is the same as the receiving interface.

Interface: GigabitEthernet1/0/1 sender IP: 1.1.2.2 target IP: 1.1.2.1,

Explanation

The sender MAC address of a received ARP packet conflicts with the MAC address of the device.

Recommended action

No action is required.

 

ARP_SENDER_SMACCONFLICT_VSI

Message text

Packet was discarded because its sender MAC address was the MAC address of the receiving interface.

Interface: [STRING], sender IP: [STRING], target IP: [STRING],VSI index: [UINT32], link ID: [UINT32].

Variable fields

$1: Interface name.

$2: Sender IP address.

$3: Target IP address.

$4: VSI index.

$5: Link ID.

Severity level

6

Example

ARP/6/ ARP_SENDER_SMACCONFLICT_VSI: Packet discarded for the sender MAC address is the same as the receiving interface.

Interface: VSI3 sender IP: 1.1.2.2 target IP: 1.1.2.1, VSI Index: 2, Link ID: 0

Explanation

The sender MAC address of a received ARP packet conflicts with the MAC address of the device. The receiving interface is a VSI interface.