H3C Campus Fixed-Port Switches System Log Messages Reference-R65xx-6W101

HomeSupportResource CenterDiagnose & MaintainH3C Campus Fixed-Port Switches System Log Messages Reference-R65xx-6W101

 

H3C Campus Fixed-Port Switches

System Log Messages Reference – R65xx

 

 

This manual is applicable to the following switches and software versions:

 

H3C S5560X-EI Switch Series (Release 6510 and later)

H3C S6520X-HI Switch Series (Release 6510 and later)

H3C S6520X-EI Switch Series (Release 6510 and later)

H3C S6520X-SI Switch Series (Release 6510 and later)

H3C S5560X-HI Switch Series (Release 6510 and later)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Document version: 6W101-20220415

Copyright © 2022 New H3C Technologies Co., Ltd. All rights reserved.

No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of New H3C Technologies Co., Ltd.

Except for the trademarks of New H3C Technologies Co., Ltd., any trademarks that may be mentioned in this document are the property of their respective owners.

The information in this document is subject to change without notice.


Contents

Introduction· 1

System log message format 1

Managing and obtaining system log messages· 3

Obtaining log messages from the console terminal 3

Obtaining log messages from a monitor terminal 4

Obtaining log messages from the log buffer 4

Obtaining log messages from the log file· 4

Obtaining log messages from a log host 4

Software module list 4

Using this document 9

AAA messages· 10

AAA_FAILURE· 10

AAA_LAUNCH· 10

AAA_SUCCESS· 11

ACL messages· 12

ACL_ACCELERATE_NO_RES· 12

ACL_ACCELERATE_NONCONTIGUOUSMASK· 12

ACL_ACCELERATE_NOT_SUPPORT· 12

ACL_ACCELERATE_NOT_SUPPORTHOPBYHOP· 13

ACL_ACCELERATE_NOT_SUPPORTMULTITCPFLAG·· 13

ACL_ACCELERATE_UNK_ERR· 13

ACL_IPV6_STATIS_INFO·· 14

ACL_NO_MEM·· 14

ACL_STATIS_INFO·· 14

ANCP messages· 15

ANCP_INVALID_PACKET· 15

APMGR messages· 16

APMGR_AC_MEM_ALERT· 16

APMGR_ADD_AP_FAIL· 16

APMGR_ADDBAC_INFO·· 17

APMGR_AP_OFFLINE· 17

APMGR_AP_ONLINE· 17

APMGR_CWC_IMG_DOWNLOAD_COMPLETE· 18

APMGR_CWC_IMG_DOWNLOAD_START· 18

APMGR_CWC_IMG_NO_ENOUGH_SPACE· 18

APMGR_CWC_LOCAL_AC_DOWN· 19

APMGR_CWC_LOCAL_AC_UP· 19

APMGR_CWC_REBOOT· 20

APMGR_CWC_RUN_DOWNLOAD_COMPLETE· 20

APMGR_CWC_RUN_DOWNLOAD_START· 20

APMGR_CWC_RUN_NO_ENOUGH_SPACE· 21

APMGR_CWC_TUNNEL_DOWN· 21

APMGR_CWC_TUNNEL_UP· 22

APMGR_CWS_IMG_DOWNLOAD_COMPLETE· 22

APMGR_CWS_IMG_DOWNLOAD_START· 22

APMGR_CWS_LOCAL_AC_DOWN· 23

APMGR_CWS_LOCAL_AC_UP· 23

APMGR_CWS_RUN_DOWNLOAD_COMPLETE· 24

APMGR_CWS_RUN_DOWNLOAD_START· 24

APMGR_CWS_TUNNEL_DOWN· 25

APMGR_CWS_TUNNEL_UP· 25

APMGR_DELBAC_INFO·· 26

APMGR_LOCAL_AC_OFFLINE· 26

APMGR_LOCAL_AC_ONLINE· 26

ARP messages· 27

ARP_ACTIVE_ACK_NO_REPLY· 27

ARP_ACTIVE_ACK_NOREQUESTED_REPLY· 27

ARP_BINDRULETOHW_FAILED·· 28

ARP_DETECTION_LOG·· 28

ARP_DUPLICATE_IPADDR_DETECT· 29

ARP_DYNAMIC· 29

ARP_DYNAMIC_IF· 30

ARP_DYNAMIC_SLOT· 30

ARP_ENTRY_CONFLICT· 31

ARP_HOST_IP_CONFLICT· 31

ARP_LOCALPROXY_ENABLE_FAILED·· 32

ARP_RATE_EXCEEDED·· 32

ARP_RATELIMIT_NOTSUPPORT· 33

ARP_SENDER_IP_INVALID·· 33

ARP_SENDER_MAC_INVALID·· 34

ARP_SENDER_SMACCONFLICT· 34

ARP_SENDER_SMACCONFLICT_VSI 35

ARP_SRC_MAC_FOUND_ATTACK· 35

ARP_SUP_ENABLE_FAILED·· 36

ARP_TARGET_IP_INVALID·· 36

ARP_THRESHOLD_REACHED·· 36

ARP_USER_DUPLICATE_IPADDR_DETECT· 37

ARP_USER_MOVE_DETECT· 38

DUPIFIP· 38

DUPIP· 39

DUPVRRPIP· 39

ATK messages· 40

ATK_ICMP_ADDRMASK_REQ·· 40

ATK_ICMP_ADDRMASK_REQ_RAW·· 41

ATK_ICMP_ADDRMASK_REQ_RAW_SZ· 42

ATK_ICMP_ADDRMASK_REQ_SZ· 43

ATK_ICMP_ADDRMASK_RPL· 44

ATK_ICMP_ADDRMASK_RPL_RAW·· 45

ATK_ICMP_ADDRMASK_RPL_RAW_SZ· 46

ATK_ICMP_ADDRMASK_RPL_SZ· 47

ATK_ICMP_ECHO_REQ·· 48

ATK_ICMP_ECHO_REQ_RAW·· 49

ATK_ICMP_ECHO_REQ_RAW_SZ· 50

ATK_ICMP_ECHO_REQ_SZ· 51

ATK_ICMP_ECHO_RPL· 52

ATK_ICMP_ECHO_RPL_RAW·· 53

ATK_ICMP_ECHO_RPL_RAW_SZ· 54

ATK_ICMP_ECHO_RPL_SZ· 55

ATK_ICMP_FLOOD·· 56

ATK_ICMP_FLOOD_SZ· 56

ATK_ICMP_INFO_REQ·· 57

ATK_ICMP_INFO_REQ_RAW·· 58

ATK_ICMP_INFO_REQ_RAW_SZ· 59

ATK_ICMP_INFO_REQ_SZ· 60

ATK_ICMP_INFO_RPL· 61

ATK_ICMP_INFO_RPL_RAW·· 62

ATK_ICMP_INFO_RPL_RAW_SZ· 63

ATK_ICMP_INFO_RPL_SZ· 64

ATK_ICMP_LARGE· 65

ATK_ICMP_LARGE_RAW·· 66

ATK_ICMP_LARGE_RAW_SZ· 66

ATK_ICMP_LARGE_SZ· 67

ATK_ICMP_PARAPROBLEM·· 68

ATK_ICMP_PARAPROBLEM_RAW·· 69

ATK_ICMP_PARAPROBLEM_RAW_SZ· 70

ATK_ICMP_PARAPROBLEM_SZ· 71

ATK_ICMP_PINGOFDEATH· 72

ATK_ICMP_PINGOFDEATH_RAW·· 73

ATK_ICMP_PINGOFDEATH_RAW_SZ· 73

ATK_ICMP_PINGOFDEATH_SZ· 74

ATK_ICMP_REDIRECT· 75

ATK_ICMP_REDIRECT_RAW·· 76

ATK_ICMP_REDIRECT_RAW_SZ· 77

ATK_ICMP_REDIRECT_SZ· 78

ATK_ICMP_SMURF· 79

ATK_ICMP_SMURF_RAW·· 80

ATK_ICMP_SMURF_RAW_SZ· 81

ATK_ICMP_SMURF_SZ· 82

ATK_ICMP_SOURCEQUENCH· 83

ATK_ICMP_SOURCEQUENCH_RAW·· 84

ATK_ICMP_SOURCEQUENCH_RAW_SZ· 85

ATK_ICMP_SOURCEQUENCH_SZ· 86

ATK_ICMP_TIMEEXCEED·· 87

ATK_ICMP_TIMEEXCEED_RAW·· 88

ATK_ICMP_TIMEEXCEED_RAW_SZ· 89

ATK_ICMP_TIMEEXCEED_SZ· 90

ATK_ICMP_TRACEROUTE· 91

ATK_ICMP_TRACEROUTE_RAW·· 92

ATK_ICMP_TRACEROUTE_RAW_SZ· 92

ATK_ICMP_TRACEROUTE_SZ· 93

ATK_ICMP_TSTAMP_REQ·· 94

ATK_ICMP_TSTAMP_REQ_RAW·· 95

ATK_ICMP_TSTAMP_REQ_RAW_SZ· 96

ATK_ICMP_TSTAMP_REQ_SZ· 97

ATK_ICMP_TSTAMP_RPL· 98

ATK_ICMP_TSTAMP_RPL_RAW·· 99

ATK_ICMP_TSTAMP_RPL_RAW_SZ· 100

ATK_ICMP_TSTAMP_RPL_SZ· 101

ATK_ICMP_TYPE· 102

ATK_ICMP_TYPE_RAW·· 103

ATK_ICMP_TYPE_RAW_SZ· 104

ATK_ICMP_TYPE_SZ· 105

ATK_ICMP_UNREACHABLE· 106

ATK_ICMP_UNREACHABLE_RAW·· 107

ATK_ICMP_UNREACHABLE_RAW_SZ· 108

ATK_ICMP_UNREACHABLE_SZ· 109

ATK_ICMPV6_DEST_UNREACH· 110

ATK_ICMPV6_DEST_UNREACH_RAW·· 111

ATK_ICMPV6_DEST_UNREACH_RAW_SZ· 111

ATK_ICMPV6_DEST_UNREACH_SZ· 112

ATK_ICMPV6_ECHO_REQ·· 113

ATK_ICMPV6_ECHO_REQ_RAW·· 114

ATK_ICMPV6_ECHO_REQ_RAW_SZ· 114

ATK_ICMPV6_ECHO_REQ_SZ· 115

ATK_ICMPV6_ECHO_RPL· 116

ATK_ICMPV6_ECHO_RPL_RAW·· 117

ATK_ICMPV6_ECHO_RPL_RAW_SZ· 117

ATK_ICMPV6_ECHO_RPL_SZ· 118

ATK_ICMPV6_FLOOD·· 119

ATK_ICMPV6_FLOOD_SZ· 119

ATK_ICMPV6_GROUPQUERY· 120

ATK_ICMPV6_GROUPQUERY_RAW·· 121

ATK_ICMPV6_GROUPQUERY_RAW_SZ· 121

ATK_ICMPV6_GROUPQUERY_SZ· 122

ATK_ICMPV6_GROUPREDUCTION· 123

ATK_ICMPV6_GROUPREDUCTION_RAW·· 124

ATK_ICMPV6_GROUPREDUCTION_RAW_SZ· 124

ATK_ICMPV6_GROUPREDUCTION_SZ· 125

ATK_ICMPV6_GROUPREPORT· 126

ATK_ICMPV6_GROUPREPORT_RAW·· 127

ATK_ICMPV6_GROUPREPORT_RAW_SZ· 127

ATK_ICMPV6_GROUPREPORT_SZ· 128

ATK_ICMPV6_LARGE· 129

ATK_ICMPV6_LARGE_RAW·· 129

ATK_ICMPV6_LARGE_RAW_SZ· 130

ATK_ICMPV6_LARGE_SZ· 130

ATK_ICMPV6_PACKETTOOBIG·· 131

ATK_ICMPV6_PACKETTOOBIG_RAW·· 132

ATK_ICMPV6_PACKETTOOBIG_RAW_SZ· 132

ATK_ICMPV6_PACKETTOOBIG_SZ· 133

ATK_ICMPV6_PARAPROBLEM·· 134

ATK_ICMPV6_PARAPROBLEM_RAW·· 135

ATK_ICMPV6_PARAPROBLEM_RAW_SZ· 135

ATK_ICMPV6_PARAPROBLEM_SZ· 136

ATK_ICMPV6_TIMEEXCEED·· 137

ATK_ICMPV6_TIMEEXCEED_RAW·· 138

ATK_ICMPV6_TIMEEXCEED_RAW_SZ· 138

ATK_ICMPV6_TIMEEXCEED_SZ· 139

ATK_ICMPV6_TRACEROUTE· 140

ATK_ICMPV6_TRACEROUTE_RAW·· 141

ATK_ICMPV6_TRACEROUTE_RAW_SZ· 142

ATK_ICMPV6_TRACEROUTE_SZ· 143

ATK_ICMPV6_TYPE· 144

ATK_ICMPV6_TYPE _RAW_SZ· 145

ATK_ICMPV6_TYPE_RAW·· 145

ATK_ICMPV6_TYPE_SZ· 146

ATK_IP_OPTION· 147

ATK_IP_OPTION_RAW·· 148

ATK_IP_OPTION_RAW_SZ· 149

ATK_IP_OPTION_SZ· 150

ATK_IP4_ACK_FLOOD·· 151

ATK_IP4_ACK_FLOOD_SZ· 151

ATK_IP4_DIS_PORTSCAN· 152

ATK_IP4_DIS_PORTSCAN_SZ· 152

ATK_IP4_DNS_FLOOD·· 153

ATK_IP4_DNS_FLOOD_SZ· 153

ATK_IP4_FIN_FLOOD·· 154

ATK_IP4_FIN_FLOOD_SZ· 154

ATK_IP4_FRAGMENT· 155

ATK_IP4_FRAGMENT_RAW·· 156

ATK_IP4_FRAGMENT_RAW_SZ· 157

ATK_IP4_FRAGMENT_SZ· 158

ATK_IP4_HTTP_FLOOD·· 159

ATK_IP4_HTTP_FLOOD_SZ· 159

ATK_IP4_IMPOSSIBLE· 160

ATK_IP4_IMPOSSIBLE_RAW·· 161

ATK_IP4_IMPOSSIBLE_RAW_SZ· 162

ATK_IP4_IMPOSSIBLE_SZ· 163

ATK_IP4_IPSWEEP· 164

ATK_IP4_IPSWEEP_SZ· 164

ATK_IP4_PORTSCAN· 165

ATK_IP4_PORTSCAN_SZ· 165

ATK_IP4_RST_FLOOD·· 166

ATK_IP4_RST_FLOOD_SZ· 166

ATK_IP4_SYN_FLOOD·· 167

ATK_IP4_SYN_FLOOD_SZ· 167

ATK_IP4_SYNACK_FLOOD·· 168

ATK_IP4_SYNACK_FLOOD_SZ· 168

ATK_IP4_TCP_ALLFLAGS· 169

ATK_IP4_TCP_ALLFLAGS_RAW·· 170

ATK_IP4_TCP_ALLFLAGS_RAW_SZ· 170

ATK_IP4_TCP_ALLFLAGS_SZ· 171

ATK_IP4_TCP_FINONLY· 172

ATK_IP4_TCP_FINONLY_RAW·· 173

ATK_IP4_TCP_FINONLY_RAW_SZ· 173

ATK_IP4_TCP_FINONLY_SZ· 174

ATK_IP4_TCP_INVALIDFLAGS· 175

ATK_IP4_TCP_INVALIDFLAGS_RAW·· 176

ATK_IP4_TCP_INVALIDFLAGS_RAW_SZ· 177

ATK_IP4_TCP_INVALIDFLAGS_SZ· 178

ATK_IP4_TCP_LAND·· 179

ATK_IP4_TCP_LAND_RAW·· 180

ATK_IP4_TCP_LAND_RAW_SZ· 180

ATK_IP4_TCP_LAND_SZ· 181

ATK_IP4_TCP_NULLFLAG·· 182

ATK_IP4_TCP_NULLFLAG_RAW·· 183

ATK_IP4_TCP_NULLFLAG_RAW_SZ· 183

ATK_IP4_TCP_NULLFLAG_SZ· 184

ATK_IP4_TCP_SYNFIN· 185

ATK_IP4_TCP_SYNFIN_RAW·· 186

ATK_IP4_TCP_SYNFIN_RAW_SZ· 186

ATK_IP4_TCP_SYNFIN_SZ· 187

ATK_IP4_TCP_WINNUKE· 188

ATK_IP4_TCP_WINNUKE_RAW·· 189

ATK_IP4_TCP_WINNUKE_RAW_SZ· 189

ATK_IP4_TCP_WINNUKE_SZ· 190

ATK_IP4_TEARDROP· 191

ATK_IP4_TEARDROP_RAW·· 192

ATK_IP4_TEARDROP_RAW_SZ· 193

ATK_IP4_TEARDROP_SZ· 194

ATK_IP4_TINY_FRAGMENT· 195

ATK_IP4_TINY_FRAGMENT_RAW·· 196

ATK_IP4_TINY_FRAGMENT_RAW_SZ· 197

ATK_IP4_TINY_FRAGMENT_SZ· 198

ATK_IP4_UDP_BOMB· 199

ATK_IP4_UDP_BOMB_RAW·· 200

ATK_IP4_UDP_BOMB_RAW_SZ· 201

ATK_IP4_UDP_BOMB_SZ· 202

ATK_IP4_UDP_FLOOD·· 203

ATK_IP4_UDP_FLOOD_SZ· 203

ATK_IP4_UDP_FRAGGLE· 204

ATK_IP4_UDP_FRAGGLE_RAW·· 205

ATK_IP4_UDP_FRAGGLE_RAW_SZ· 205

ATK_IP4_UDP_FRAGGLE_SZ· 206

ATK_IP4_UDP_SNORK· 207

ATK_IP4_UDP_SNORK_RAW·· 208

ATK_IP4_UDP_SNORK_RAW_SZ· 208

ATK_IP4_UDP_SNORK_SZ· 209

ATK_IP6_ACK_FLOOD·· 210

ATK_IP6_ACK_FLOOD_SZ· 210

ATK_IP6_DIS_PORTSCAN· 211

ATK_IP6_DIS_PORTSCAN_SZ· 211

ATK_IP6_DNS_FLOOD·· 212

ATK_IP6_DNS_FLOOD_SZ· 212

ATK_IP6_FIN_FLOOD·· 213

ATK_IP6_FIN_FLOOD_SZ· 213

ATK_IP6_FRAGMENT· 214

ATK_IP6_FRAGMENT_RAW·· 215

ATK_IP6_FRAGMENT_RAW_SZ· 215

ATK_IP6_FRAGMENT_SZ· 216

ATK_IP6_HTTP_FLOOD·· 217

ATK_IP6_HTTP_FLOOD_SZ· 217

ATK_IP6_IMPOSSIBLE· 218

ATK_IP6_IMPOSSIBLE_RAW·· 219

ATK_IP6_IMPOSSIBLE_RAW_SZ· 219

ATK_IP6_IMPOSSIBLE_SZ· 220

ATK_IP6_IPSWEEP· 220

ATK_IP6_IPSWEEP_SZ· 221

ATK_IP6_PORTSCAN· 221

ATK_IP6_PORTSCAN_SZ· 222

ATK_IP6_RST_FLOOD·· 222

ATK_IP6_RST_FLOOD_SZ· 223

ATK_IP6_SYN_FLOOD·· 223

ATK_IP6_SYN_FLOOD_SZ· 224

ATK_IP6_SYNACK_FLOOD·· 224

ATK_IP6_SYNACK_FLOOD_SZ· 225

ATK_IP6_TCP_ALLFLAGS· 225

ATK_IP6_TCP_ALLFLAGS_RAW·· 226

ATK_IP6_TCP_ALLFLAGS_RAW_SZ· 226

ATK_IP6_TCP_ALLFLAGS_SZ· 227

ATK_IP6_TCP_FINONLY· 228

ATK_IP6_TCP_FINONLY_RAW·· 228

ATK_IP6_TCP_FINONLY_RAW_SZ· 229

ATK_IP6_TCP_FINONLY_SZ· 229

ATK_IP6_TCP_INVALIDFLAGS· 230

ATK_IP6_TCP_INVALIDFLAGS_RAW·· 231

ATK_IP6_TCP_INVALIDFLAGS_RAW_SZ· 232

ATK_IP6_TCP_INVALIDFLAGS_SZ· 233

ATK_IP6_TCP_LAND·· 234

ATK_IP6_TCP_LAND_RAW·· 234

ATK_IP6_TCP_LAND_RAW_SZ· 235

ATK_IP6_TCP_LAND_SZ· 235

ATK_IP6_TCP_NULLFLAG·· 236

ATK_IP6_TCP_NULLFLAG_RAW·· 236

ATK_IP6_TCP_NULLFLAG_RAW_SZ· 237

ATK_IP6_TCP_NULLFLAG_SZ· 237

ATK_IP6_TCP_SYNFIN· 238

ATK_IP6_TCP_SYNFIN_RAW·· 238

ATK_IP6_TCP_SYNFIN_RAW_SZ· 239

ATK_IP6_TCP_SYNFIN_SZ· 239

ATK_IP6_TCP_WINNUKE· 240

ATK_IP6_TCP_WINNUKE_RAW·· 240

ATK_IP6_TCP_WINNUKE_RAW_SZ· 241

ATK_IP6_TCP_WINNUKE_SZ· 241

ATK_IP6_UDP_FLOOD·· 242

ATK_IP6_UDP_FLOOD_SZ· 242

ATK_IP6_UDP_FRAGGLE· 243

ATK_IP6_UDP_FRAGGLE_RAW·· 243

ATK_IP6_UDP_FRAGGLE_RAW_SZ· 244

ATK_IP6_UDP_FRAGGLE_SZ· 244

ATK_IP6_UDP_SNORK· 245

ATK_IP6_UDP_SNORK_RAW·· 245

ATK_IP6_UDP_SNORK_RAW_SZ· 246

ATK_IP6_UDP_SNORK_SZ· 246

ATK_IPOPT_ABNORMAL· 247

ATK_IPOPT_ABNORMAL_RAW·· 248

ATK_IPOPT_ABNORMAL_RAW_SZ· 249

ATK_IPOPT_ABNORMAL_SZ· 250

ATK_IPOPT_LOOSESRCROUTE· 251

ATK_IPOPT_LOOSESRCROUTE_RAW·· 252

ATK_IPOPT_LOOSESRCROUTE_RAW_SZ· 253

ATK_IPOPT_LOOSESRCROUTE_SZ· 254

ATK_IPOPT_RECORDROUTE· 255

ATK_IPOPT_RECORDROUTE_RAW·· 256

ATK_IPOPT_RECORDROUTE_RAW_SZ· 257

ATK_IPOPT_RECORDROUTE_SZ· 258

ATK_IPOPT_ROUTEALERT· 259

ATK_IPOPT_ROUTEALERT_RAW·· 260

ATK_IPOPT_ROUTEALERT_RAW_SZ· 261

ATK_IPOPT_ROUTEALERT_SZ· 262

ATK_IPOPT_SECURITY· 263

ATK_IPOPT_SECURITY_RAW·· 264

ATK_IPOPT_SECURITY_RAW_SZ· 265

ATK_IPOPT_SECURITY_SZ· 266

ATK_IPOPT_STREAMID·· 267

ATK_IPOPT_STREAMID_RAW·· 268

ATK_IPOPT_STREAMID_RAW_SZ· 269

ATK_IPOPT_STREAMID_SZ· 270

ATK_IPOPT_STRICTSRCROUTE· 271

ATK_IPOPT_STRICTSRCROUTE_RAW·· 272

ATK_IPOPT_STRICTSRCROUTE_RAW_SZ· 273

ATK_IPOPT_STRICTSRCROUTE_SZ· 274

ATK_IPOPT_TIMESTAMP· 275

ATK_IPOPT_TIMESTAMP_RAW·· 276

ATK_IPOPT_TIMESTAMP_RAW_SZ· 277

ATK_IPOPT_TIMESTAMP_SZ· 278

ATK_IPV6_EXT_HEADER· 279

ATK_IPV6_EXT_HEADER_RAW·· 280

ATK_IPV6_EXT_HEADER_RAW_SZ· 280

ATK_IPV6_EXT_HEADER_SZ· 281

ATM·· 282

ATM_PVCDOWN· 282

ATM_PVCUP· 282

BFD messages· 284

BFD_CHANGE_FSM·· 284

BFD_REACHED_UPPER_LIMIT· 284

BGP messages· 285

BGP_EXCEED_ROUTE_LIMIT· 285

BGP_REACHED_THRESHOLD·· 285

BGP_LOG_ROUTE_FLAP· 286

BGP_MEM_ALERT· 286

BGP_PEER_LICENSE_REACHED·· 286

BGP_ROUTE_LICENSE_REACHED·· 287

BGP_STATE_CHANGED·· 287

BGP_STATE_CHANGED_REASON· 288

BLS messages· 289

BLS_ENTRY_ADD·· 289

BLS_ENTRY_DEL· 289

BLS_IPV6_ENTRY_ADD·· 290

BLS_IPV6_ENTRY_DEL· 290

CFD messages· 291

CFD_CROSS_CCM·· 291

CFD_ERROR_CCM·· 291

CFD_LOST_CCM·· 292

CFD_RECEIVE_CCM·· 292

CFGMAN messages· 293

CFGMAN_ARCHIVE_SCP_FAIL· 293

CFGMAN_CFGCHANGED·· 293

CFGMAN_EXIT_FROM_CONFIGURE· 294

CFGMAN_OPTCOMPLETION· 294

CONNLMT messages· 296

CONNLMT_IPV4_OVERLOAD·· 296

CONNLMT_IPV4_RECOVER· 297

CONNLMT_IPV6_OVERLOAD·· 298

CONNLMT_IPV6_RECOVER· 299

DEV messages· 300

BOARD_REBOOT· 300

BOARD_REMOVED·· 300

BOARD_STATE_FAULT· 301

BOARD_STATE_NORMAL· 301

CFCARD_INSERTED·· 301

CFCARD_REMOVED·· 302

CHASSIS_REBOOT· 302

DEV_CLOCK_CHANGE· 302

DEV_FAULT_TOOLONG·· 303

DEV_MNT_LogToIC· 303

FAN_ABSENT· 304

FAN_DIRECTION_NOT_PREFERRED·· 304

FAN_FAILED·· 305

FAN_RECOVERED·· 305

MAD_DETECT· 306

MAD_PROC· 306

POWER_ABSENT· 307

POWER_FAILED·· 307

POWER_MONITOR_ABSENT· 308

POWER_MONITOR_FAILED·· 308

POWER_MONITOR_RECOVERED·· 309

POWER_RECOVERED·· 309

RPS_ABSENT· 310

RPS_FAILED·· 310

RPS_NORMAL· 311

SUBCARD_FAULT· 311

SUBCARD_INSERTED·· 312

SUBCARD_REBOOT· 312

SUBCARD_REMOVED·· 313

SYSTEM_REBOOT· 313

TEMPERATURE_ALARM·· 314

TEMPERATURE_LOW·· 315

TEMPERATURE_NORMAL· 316

TEMPERATURE_SHUTDOWN· 317

TEMPERATURE_WARNING·· 318

VCHK_VERSION_INCOMPATIBLE· 318

DHCP·· 319

DHCP_NOTSUPPORTED·· 319

DHCP_NORESOURCES· 319

DHCPR·· 320

DHCPR_SERVERCHANGE· 320

DHCPR_SWITCHMASTER· 320

DHCPS messages· 321

DHCPS_ALLOCATE_IP· 321

DHCPS_CONFLICT_IP· 321

DHCPS_EXTEND_IP· 322

DHCPS_FILE· 322

DHCPS_RECLAIM_IP· 323

DHCPS_VERIFY_CLASS· 323

DHCPS6 messages· 324

DHCPS6_ALLOCATE_ADDRESS· 324

DHCPS6_ALLOCATE_PREFIX· 324

DHCPS6_CONFLICT_ADDRESS· 325

DHCPS6_EXTEND_ADDRESS· 325

DHCPS6_EXTEND_PREFIX· 326

DHCPS6_FILE· 326

DHCPS6_RECLAIM_ADDRESS· 327

DHCPS6_RECLAIM_PREFIX· 327

DHCPSP4· 328

DHCPSP4_FILE· 328

DHCPSP6· 329

DHCPSP6_FILE· 329

DIAG messages· 330

CPU_MINOR_RECOVERY· 330

CPU_MINOR_THRESHOLD·· 331

CPU_SEVERE_RECOVERY· 332

CPU_SEVERE_THRESHOLD·· 333

CPU_USAGE_LASTMINUTE· 334

MEM_ALERT· 335

MEM_BELOW_THRESHOLD·· 336

MEM_EXCEED_THRESHOLD·· 337

MEM_USAGE· 337

DIAG_STORAGE_BELOW_THRESHOLD·· 338

DIAG_STORAGE_EXCEED_THRESHOLD·· 338

DLDP messages· 339

DLDP_AUTHENTICATION_FAILED·· 339

DLDP_LINK_BIDIRECTIONAL· 339

DLDP_LINK_SHUTMODECHG·· 340

DLDP_LINK_UNIDIRECTIONAL· 340

DLDP_NEIGHBOR_AGED·· 341

DLDP_NEIGHBOR_CONFIRMED·· 341

DLDP_NEIGHBOR_DELETED·· 342

DOT1X messages· 343

DOT1X_CONFIG_NOTSUPPORT· 343

DOT1X_LOGIN_FAILURE· 343

DOT1X_LOGIN_SUCC· 344

DOT1X_LOGIN_SUCC (in open mode) 344

DOT1X_LOGOFF· 345

DOT1X_LOGOFF (in open mode) 345

DOT1X_LOGOFF_ABNORMAL· 346

DOT1X_LOGOFF_ABNORMAL (in open mode) 347

DOT1X_MACBINDING_EXIST· 347

DOT1X_NOTENOUGH_EADFREEIP_RES· 348

DOT1X_NOTENOUGH_EADFREERULE_RES· 348

DOT1X_NOTENOUGH_EADMACREDIR_RES· 348

DOT1X_NOTENOUGH_EADPORTREDIR_RES· 349

DOT1X_NOTENOUGH_ENABLEDOT1X_RES· 349

DOT1X_PEXAGG_NOMEMBER_RES· 349

DOT1X_SMARTON_FAILURE· 350

DOT1X_UNICAST_NOT_EFFECTIVE· 350

DRNI 351

DRNI_AUTORECOVERY_TIMEOUT· 351

DRNI_GLBCHECK_CONSISTENCY· 351

DRNI_GLBCHECK_INCONSISTENCY· 352

DRNI_IFCHECK_CONSISTENCY· 352

DRNI_IFCHECK_INCONSISTENCY· 352

DRNI_IFEVENT_DR_BIND·· 353

DRNI_IFEVENT_DR_GLOBALDOWN· 353

DRNI_IFEVENT_DR_GLOBALUP· 353

DRNI_IFEVENT_DR_MAC_CHANGE· 354

DRNI_IFEVENT_DR_NOSELECTED·· 354

DRNI_IFEVENT_DR_PEER_NOSELECTED·· 355

DRNI_IFEVENT_DR_PEER_SELECTED·· 355

DRNI_IFEVENT_DR_PRIORITY_CHANGE· 355

DRNI_IFEVENT_DR_SELECTED·· 356

DRNI_IFEVENT_DR_UNBIND·· 356

DRNI_IFEVENT_IPP_BIND·· 356

DRNI_IFEVENT_IPP_DOWN· 357

DRNI_IFEVENT_IPP_UNBIND·· 357

DRNI_IFEVENT_IPP_UP· 358

DRNI_IPP_BLOCK· 358

DRNI_IPP_UNBLOCK· 358

DRNI_KEEPALIVEINTERVAL_MISMATCH· 359

DRNI_KEEPALIVELINK_DOWN· 359

DRNI_KEEPALIVELINK_UP· 359

DRNI_DEVICE_MADDOWN· 360

DRNI_DEVICE_MADRECOVERY· 360

DRNI_SYSEVENT_DEVICEROLE_CHANGE· 361

DRNI_SYSEVENT_MAC_CHANGE· 361

DRNI_SYSEVENT_MODE_CHANGE· 362

DRNI_SYSEVENT_NUMBER_CHANGE· 362

DRNI_SYSEVENT_PRIORITY_CHANGE· 362

DRVPLAT· 363

DRVPLAT_ECMP_NO_RESOURCE· 363

DRVPLAT_MAC_Conflict 363

DRVPLAT_NO_ENOUGH_RESOURCE· 364

DRVPLAT_Not_Enough_Resource· 364

DRVPLAT_POE_AI_DISCONNET_AC· 364

DRVPLAT_POE_AI_DISCONNET_DELAY· 365

DRVPLAT_POE_AI_HIGH_INRUSH· 365

DRVPLAT_POE_AI_PORT_MAXPOWER· 366

DRVPLAT_POE_AI_PORT_RESTART· 367

DRVPLAT_PORT_ATTACK_OCCUR· 368

DRVPLAT_SOFTCAR_DROP· 369

DRVPLAT_VPN_Conflict 369

DRVPLAT_VPN_MAYBE_Conflict 370

EDEV messages· 371

ALARM_IN_REMOVED·· 371

ALARM_IN_REPORTED·· 371

EDEV_BOOTROM_UPDATE_FAILED·· 371

EDEV_BOOTROM_UPDATE_SUCCESS· 372

EDEV_FAILOVER_GROUP_STATE_CHANGE· 372

eMDI messages· 373

EMDI_INDICATOR_OVER_THRES· 373

EMDI_INDICATOR_OVER_THRES_RESUME· 374

EMDI_INSTANCE_CONFLICT_FLOW·· 374

EMDI_INSTANCE_EXCEED·· 375

EMDI_INSTANCE_SAME_FLOW·· 375

EPA messages· 376

EPA_ENDPOINT_ONLINE· 376

EPA_ENDPOINT_OFFLINE· 376

EPA_DEVICETYPE_CHANGE· 377

ERPS messages· 378

ERPS_STATE_CHANGED·· 378

ETH messages· 379

ETH_SET_MAC_FAILED·· 379

ETHDRNI 380

ETHDRNI_MAC_INEFFECTIVE· 380

ETHOAM messages· 381

ETHOAM_CONNECTION_FAIL_DOWN· 381

ETHOAM_CONNECTION_FAIL_TIMEOUT· 381

ETHOAM_CONNECTION_FAIL_UNSATISF· 382

ETHOAM_CONNECTION_SUCCEED·· 382

ETHOAM_DISABLE· 382

ETHOAM_DISCOVERY_EXIT· 383

ETHOAM_ENABLE· 383

ETHOAM_ENTER_LOOPBACK_CTRLLED·· 383

ETHOAM_ENTER_LOOPBACK_CTRLLING·· 384

ETHOAM_LOCAL_DYING_GASP· 384

ETHOAM_LOCAL_ERROR_FRAME· 384

ETHOAM_LOCAL_ERROR_FRAME_PERIOD·· 385

ETHOAM_LOCAL_ERROR_FRAME_SECOND·· 385

ETHOAM_LOCAL_ERROR_SYMBOL· 385

ETHOAM_LOCAL_LINK_FAULT· 386

ETHOAM_LOOPBACK_EXIT· 386

ETHOAM_LOOPBACK_EXIT_ERROR_STATU· 386

ETHOAM_LOOPBACK_NO_RESOURCE· 387

ETHOAM_LOOPBACK_NOT_SUPPORT· 387

ETHOAM_QUIT_LOOPBACK_CTRLLED·· 387

ETHOAM_QUIT_LOOPBACK_CTRLLING·· 388

ETHOAM_REMOTE_CRITICAL· 388

ETHOAM_REMOTE_DYING_GASP· 388

ETHOAM_REMOTE_ERROR_FRAME· 389

ETHOAM_REMOTE_ERROR_FRAME_PERIOD·· 389

ETHOAM_REMOTE_ERROR_FRAME_SECOND·· 389

ETHOAM_REMOTE_ERROR_SYMBOL· 390

ETHOAM_REMOTE_EXIT· 390

ETHOAM_REMOTE_FAILURE_RECOVER· 390

ETHOAM_REMOTE_LINK_FAULT· 391

ETHOAM_NO_ENOUGH_RESOURCE· 391

ETHOAM_NOT_CONNECTION_TIMEOUT· 391

EVB messages· 392

EVB_AGG_FAILED·· 392

EVB_LICENSE_EXPIRE· 392

EVB_VSI_OFFLINE· 393

EVB_VSI_ONLINE· 393

EVIISIS messages· 394

EVIISIS_LICENSE_EXPIRED·· 394

EVIISIS_LICENSE_EXPIRED_TIME· 394

EVIISIS_LICENSE_UNAVAILABLE· 394

EVIISIS_NBR_CHG·· 395

FCLINK messages· 396

FCLINK_FDISC_REJECT_NORESOURCE· 396

FCLINK_FLOGI_REJECT_NORESOURCE· 396

FCOE messages· 397

FCOE_INTERFACE_NOTSUPPORT_FCOE· 397

FCOE_LAGG_BIND_ACTIVE· 397

FCOE_LAGG_BIND_DEACTIVE· 398

FCZONE messages· 399

FCZONE_DISTRIBUTE_FAILED·· 399

FCZONE_HARDZONE_DISABLED·· 399

FCZONE_HARDZONE_ENABLED·· 400

FCZONE_ISOLATE_ALLNEIGHBOR· 400

FCZONE_ISOLATE_CLEAR_VSAN· 401

FCZONE_ISOLATE_CLEAR_ALLVSAN· 401

FCZONE_ISOLATE_NEIGHBOR· 401

FGROUP messages· 402

FLOWGROUP_APPLY_FAIL· 402

FLOWGROUP_MODIFY_FAIL· 402

FIB messages· 403

FIB_FILE· 403

FILTER messages· 404

FILTER_EXECUTION_ICMP· 404

FILTER_EXECUTION_ICMPV6· 405

FILTER_IPV4_EXECUTION· 406

FILTER_IPV6_EXECUTION· 407

FIPSNG messages· 408

FIPSNG_HARD_RESOURCE_NOENOUGH· 408

FIPSNG_HARD_RESOURCE_RESTORE· 408

FS messages· 409

FS_UNFORMATTED_PARTITION· 409

FTP messages· 410

FTP_ACL_DENY· 410

FTP_REACH_SESSION_LIMIT· 410

FTPD_AUTHOR_FAILED·· 411

gRPC messages· 412

GRPC_LOGIN· 412

GRPC_LOGIN_FAILED·· 412

GRPC_LOGOUT· 413

GRPC_SERVER_FAILED·· 413

GRPC_SUBSCRIBE_EVENT_FAILED·· 413

GRPC_RECEIVE_SUBSCRIPTION· 414

HA messages· 415

HA_BATCHBACKUP_FINISHED·· 415

HA_BATCHBACKUP_STARTED·· 415

HA_STANDBY_NOT_READY· 415

HA_STANDBY_TO_MASTER· 416

HLTH messages· 417

LIPC_COMM_FAULTY· 417

LIPC_COMM_RECOVER· 417

HQOS messages· 418

HQOS_DP_SET_FAIL· 418

HQOS_FP_SET_FAIL· 418

HQOS_POLICY_APPLY_FAIL· 419

HQOS_POLICY_APPLY_FAIL· 419

HTTPD messages· 420

HTTPD_CONNECT· 420

HTTPD_CONNECT_TIMEOUT· 420

HTTPD_DISCONNECT· 421

HTTPD_FAIL_FOR_ACL· 421

HTTPD_FAIL_FOR_ACP· 421

HTTPD_REACH_CONNECT_LIMIT· 422

IFNET messages· 423

IF_BUFFER_CONGESTION_OCCURRENCE· 423

IF_BUFFER_CONGESTION_CLEAR· 423

IF_JUMBOFRAME_WARN· 424

IF_LINKFLAP_DETECTED·· 424

INTERFACE_NOTSUPPRESSED·· 424

INTERFACE_SUPPRESSED·· 425

LINK_UPDOWN· 425

PFC_WARNING·· 426

PHY_UPDOWN· 426

PROTOCOL_UPDOWN· 426

STORM_CONSTRAIN_BELOW·· 427

STORM_CONSTRAIN_CONTROLLED·· 427

STORM_CONSTRAIN_EXCEED·· 428

STORM_CONSTRAIN_NORMAL· 428

TUNNEL_LINK_UPDOWN· 429

TUNNEL_PHY_UPDOWN· 429

VLAN_MODE_CHANGE· 429

IKE messages· 430

IKE_P1_SA_ESTABLISH_FAIL· 430

IKE_P2_SA_ESTABLISH_FAIL· 431

IKE_P2_SA_TERMINATE· 431

IKE_VERIFY_CERT_FAIL· 432

IMA·· 434

IMA_ALLOCATE_FAILED·· 434

IMA_DATA_ERROR· 434

IMA_FILE_HASH_FAILED·· 434

IMA_RM_FILE_MISS· 435

IMA_RM_HASH_MISS· 435

IMA_TEMPLATE_ERROR· 435

iNQA messages· 436

INQA_BWD_LOSS_EXCEED·· 436

INQA_BWD_LOSS_RECOV· 436

INQA_DEBUG_FAIL· 436

INQA_FLAG_DIFF· 437

INQA_FLAG_FAIL· 437

INQA_FLOW_DIFF· 437

INQA_FWD_LOSS_EXCEED·· 438

INQA_FWD_LOSS_RECOV· 438

INQA_INST_FAIL· 438

INQA_INTVL_DIFF· 439

INQA_NO_RESOURCE· 439

INQA_NO_SUPPORT· 439

INQA_SMOOTH_BEGIN_FAIL· 440

INQA_SMOOTH_END_FAIL· 440

IP6ADDR·· 441

IP6ADDR_CREATEADDRESS_ERROR· 441

IP6ADDR_FUNCTION_FAIL· 441

IP6FW··· 442

IPv6_MTU_SET_DRV_NOT_SUPPORT· 442

IPADDR messages· 443

IPADDR_HA_EVENT_ERROR· 443

IPADDR_HA_STOP_EVENT· 444

IPFW··· 445

IPFW_FAILURE· 445

IPv4_MTU_SET_DRV_NOT_SUPPORT· 445

IPSEC messages· 446

IPSEC_FAILED_ADD_FLOW_TABLE· 446

IPSEC_PACKET_DISCARDED·· 446

IPSEC_SA_ESTABLISH· 447

IPSEC_SA_ESTABLISH_FAIL· 447

IPSEC_SA_INITINATION· 448

IPSEC_SA_TERMINATE· 448

IPSG messages· 449

IPSG_ADDENTRY_ERROR· 449

IPSG_ADDEXCLUDEDVLAN_ERROR· 450

IPSG_ARP_LOCALMAC_CONFLICT· 450

IPSG_ARP_REMOTEMAC_CONFLICT· 451

IPSG_DELENTRY_ERROR· 451

IPSG_DELEXCLUDEDVLAN_ERROR· 452

IPSG_MAC_CONFLICT· 452

IPSG_ND_LOCALMAC_CONFLICT· 453

IPSG_ND_REMOTEMAC_CONFLICT· 453

IPSG_IPV4_ALARMCLEAR· 454

IPSG_IPV4_ALARMEMERGE· 454

IPSG_IPV6_ALARMCLEAR· 454

IPSG_IPV6_ALARMEMERGE· 455

IRDP messages· 456

IRDP_EXCEED_ADVADDR_LIMIT· 456

IRF· 457

IRF_LINK_BLOCK· 457

IRF_LINK_DOWN· 457

IRF_LINK_UP· 457

IRF_MEMBERID_CONFLICT· 458

IRF_MERGE· 458

IRF_MERGE_NEED_REBOOT· 458

IRF_MERGE_NOT_NEED_REBOOT· 459

ISIS messages· 460

ISIS_LSP_CONFLICT· 460

ISIS_MEM_ALERT· 460

ISIS_NBR_CHG·· 461

ISSU messages· 462

ISSU_LOAD_FAILED·· 462

ISSU_LOAD_SUCCESS· 462

ISSU_PROCESSWITCHOVER· 462

ISSU_ROLLBACKCHECKNORMAL· 463

L2PT messages· 464

L2PT_SET_MULTIMAC_FAILED·· 464

L2PT_CREATE_TUNNELGROUP_FAILED·· 464

L2PT_ADD_GROUPMEMBER_FAILED·· 464

L2PT_ENABLE_DROP_FAILED·· 465

L2TPv2 messages· 466

L2TPV2_TUNNEL_EXCEED_LIMIT· 466

L2TPV2_SESSION_EXCEED_LIMIT· 466

L2VPN messages· 467

EVPN_GLOBAL_MAC_CONFLICT· 467

L2VPN_ARP_MOBILITY_SUPPRESS (public instance) 467

L2VPN_ARP_MOBILITY_SUPPRESS (VPN instance) 468

L2VPN_ARP_MOBILITY_UNSUPPRESS (public instance) 468

L2VPN_ARP_MOBILITY_UNSUPPRESS (VPN instance) 469

L2VPN_MAC_MOBILITY_SUPPRESS· 469

L2VPN_MAC_MOBILITY_UNSUPPRESS· 470

L2VPN_BGPVC_CONFLICT_LOCAL· 470

L2VPN_BGPVC_CONFLICT_REMOTE· 471

L2VPN_HARD_RESOURCE_NOENOUGH· 471

L2VPN_HARD_RESOURCE_RESTORE· 471

L2VPN_LABEL_DUPLICATE· 472

L2VPN_MLAG_AC_CONFLICT· 472

LAGG messages· 473

LAGG_ACTIVE· 473

LAGG_AUTO_AGGREGATION· 473

LAGG_INACTIVE_AICFG·· 474

LAGG_INACTIVE_BFD·· 474

LAGG_INACTIVE_CONFIGURATION· 475

LAGG_INACTIVE_DUPLEX· 475

LAGG_INACTIVE_HARDWAREVALUE· 476

LAGG_INACTIVE_IFCFG_DEFAULT· 476

LAGG_INACTIVE_IFCFG_LOOPPORT· 477

LAGG_INACTIVE_IFCFG_NONAGG·· 477

LAGG_INACTIVE_KEY_INVALID·· 478

LAGG_INACTIVE_LOWER_LIMIT· 478

LAGG_INACTIVE_NODEREMOVE· 479

LAGG_INACTIVE_OPERSTATE· 479

LAGG_INACTIVE_PARTNER· 480

LAGG_INACTIVE_PARTNER_KEY_WRONG·· 480

LAGG_INACTIVE_PARTNER_MAC_WRONG·· 481

LAGG_INACTIVE_PARTNER_NONAGG·· 481

LAGG_INACTIVE_PARTNER_RDIRHANDLE· 482

LAGG_INACTIVE_PHYSTATE· 482

LAGG_INACTIVE_PORT_DEFAULT· 483

LAGG_INACTIVE_RDIRHANDLE· 483

LAGG_INACTIVE_REDUNDANCY· 484

LAGG_INACTIVE_RESOURCE_INSUFICIE· 484

LAGG_INACTIVE_SPEED·· 485

LAGG_INACTIVE_STANDBY· 485

LAGG_INACTIVE_UPPER_LIMIT· 486

LAGG_SELECTPORT_INCONSISTENT· 486

LDP messages· 487

LDP_ADJACENCY_DOWN· 488

LDP_MPLSLSRID_CHG·· 489

LDP_SESSION_CHG·· 490

LDP_SESSION_GR· 491

LDP_SESSION_SP· 492

LIPC messages· 493

PORT_CHANGE· 493

LLDP messages· 494

LLDP_CREATE_NEIGHBOR· 494

LLDP_DELETE_NEIGHBOR· 495

LLDP_LESS_THAN_NEIGHBOR_LIMIT· 495

LLDP_NEIGHBOR_AGE_OUT· 496

LLDP_NEIGHBOR_PROTECTION_BLOCK· 496

LLDP_NEIGHBOR_PROTECTION_DOWN· 497

LLDP_NEIGHBOR_PROTECTION_UNBLOCK· 497

LLDP_NEIGHBOR_PROTECTION_UP· 497

LLDP_PVID_INCONSISTENT· 498

LLDP_REACH_NEIGHBOR_LIMIT· 498

LOAD messages· 499

BOARD_LOADING·· 499

LOAD_FAILED·· 499

LOAD_FINISHED·· 500

LOGIN messages· 501

LOGIN_FAILED·· 501

LOGIN_ INVALID_USERNAME_PWD·· 501

LPDT messages· 502

LPDT_LOOPED·· 502

LPDT_RECOVERED·· 502

LPDT_VLAN_LOOPED·· 502

LPDT_VLAN_RECOVERED·· 503

LPDT_VSI_LOOPED·· 503

LPDT_VSI_RECOVERED·· 503

LPDT_VSI_BLOCKFAIL· 504

LS messages· 505

LOCALSVR_PROMPTED_CHANGE_PWD·· 505

LS_ADD_USER_TO_GROUP· 505

LS_AUTHEN_FAILURE· 506

LS_AUTHEN_SUCCESS· 506

LS_DEL_USER_FROM_GROUP· 507

LS_DELETE_PASSWORD_FAIL· 507

LS_PWD_ADDBLACKLIST· 507

LS_PWD_CHGPWD_FOR_AGEDOUT· 508

LS_PWD_CHGPWD_FOR_AGEOUT· 508

LS_PWD_CHGPWD_FOR_COMPOSITION· 508

LS_PWD_CHGPWD_FOR_FIRSTLOGIN· 509

LS_PWD_CHGPWD_FOR_LENGTH· 509

LS_PWD_FAILED2WRITEPASS2FILE· 509

LS_PWD_MODIFY_FAIL· 510

LS_PWD_MODIFY_SUCCESS· 510

LS_REAUTHEN_FAILURE· 511

LS_UPDATE_PASSWORD_FAIL· 511

LS_USER_CANCEL· 511

LS_USER_PASSWORD_EXPIRE· 512

LS_USER_ROLE_CHANGE· 512

LSPV messages· 513

LSPV_PING_STATIS_INFO·· 513

MAC messages· 514

MAC_DRIVER_ADD_ENTRY· 514

MAC_NOTIFICATION· 515

MAC_PROTOCOLPKT_NORES_GLOBAL· 516

MAC_PROTOCOLPKT_NORES_PORT· 516

MAC_PROTOCOLPKT_NORES_VLAN· 517

MAC_TABLE_FULL_GLOBAL· 517

MAC_TABLE_FULL_PORT· 517

MAC_TABLE_FULL_VLAN· 518

MAC_VLAN_LEARNLIMIT_NORESOURCE· 518

MAC_VLAN_LEARNLIMIT_NOTSUPPORT· 518

MACA messages· 519

MACA_ENABLE_NOT_EFFECTIVE· 519

MACA_LOGIN_FAILURE· 520

MACA_LOGIN_FAILURE (EAD) 521

MACA_LOGIN_SUCC· 522

MACA_LOGIN_SUCC (in open mode) 522

MACA_LOGOFF· 523

MACA_LOGOFF (in open mode) 523

MACSEC messages· 524

MACSEC_MKA_KEEPALIVE_TIMEOUT· 524

MACSEC_MKA_PRINCIPAL_ACTOR· 524

MACSEC_MKA_SAK_REFRESH· 525

MACSEC_MKA_SESSION_REAUTH· 525

MACSEC_MKA_SESSION_SECURED·· 526

MACSEC_MKA_SESSION_START· 526

MACSEC_MKA_SESSION_STOP· 527

MACSEC_MKA_SESSION_UNSECURED·· 527

MBFD messages· 528

MBFD_TRACEROUTE_FAILURE· 528

MBUF messages· 529

MBUF_DATA_BLOCK_CREATE_FAIL· 529

MDC messages· 530

MDC_CREATE_ERR· 530

MDC_CREATE· 530

MDC_DELETE· 531

MDC_KERNEL_EVENT_TOOLONG·· 531

MDC_LICENSE_EXPIRE· 531

MDC_NO_FORMAL_LICENSE· 532

MDC_NO_LICENSE_EXIT· 532

MDC_OFFLINE· 532

MDC_ONLINE· 533

MDC_STATE_CHANGE· 533

MFIB messages· 534

MFIB_MEM_ALERT· 534

MGROUP messages· 535

MGROUP_APPLY_SAMPLER_FAIL· 535

MGROUP_RESTORE_CPUCFG_FAIL· 535

MGROUP_RESTORE_GROUP_FAIL· 536

MGROUP_RESTORE_IFCFG_FAIL· 536

MGROUP_SYNC_CFG_FAIL· 537

MPLS messages· 538

MPLS_HARD_RESOURCE_NOENOUGH· 538

MPLS_HARD_RESOURCE_RESTORE· 538

MTLK messages· 539

MTLK_UPLINK_STATUS_CHANGE· 539

NAT messages· 540

NAT_ADDR_BIND_CONFLICT· 540

NAT_FAILED_ADD_FLOW_RULE· 540

NAT_FAILED_ADD_FLOW_TABLE· 541

NAT_FLOW·· 542

NAT_SERVER_INVALID·· 543

NAT_SERVICE_CARD_RECOVER_FAILURE· 544

ND messages· 545

ND_COMMONPROXY_ENABLE_FAILED·· 545

ND_CONFLICT· 545

ND_DUPADDR· 546

ND_HOST_IP_CONFLICT· 546

ND_LOCALPROXY_ENABLE_FAILED·· 546

ND_MAC_CHECK· 547

ND_NETWORKROUTE_DUPLICATE· 547

ND_RAGUARD_DROP· 548

ND_RATE_EXCEEDED·· 548

ND_RATELIMIT_NOTSUPPORT· 549

ND_SET_PORT_TRUST_NORESOURCE· 549

ND_SET_VLAN_REDIRECT_NORESOURCE· 549

ND_SNOOPING_LEARN_ALARM·· 550

ND_SNOOPING_LEARN_ALARM_RECOVER· 550

ND_USER_DUPLICATE_IPV6ADDR· 551

ND_USER_MOVE· 552

ND_USER_OFFLINE· 552

ND_USER_ONLINE· 553

NETCONF messages· 554

CLI 554

EDIT-CONFIG·· 555

NETCONF_MSG_DEL· 556

THREAD·· 556

NQA messages· 557

NQA_ENTRY_PROBE_RESULT· 557

NQA_LOG_UNREACHABLE· 557

NQA_START_FAILURE· 558

NQA_TWAMP_LIGHT_PACKET_INVALID·· 558

NQA_TWAMP_LIGHT_REACTION· 559

NQA_TWAMP_LIGHT_START_FAILURE· 559

NSS messages· 560

NSS_ENABLE_FAIL· 560

NSS_SESSION_TIMEOUT_FAIL· 560

NTP messages· 561

NTP_CLOCK_CHANGE· 561

NTP_LEAP_CHANGE· 561

NTP_SOURCE_CHANGE· 562

NTP_SOURCE_LOST· 562

NTP_STRATUM_CHANGE· 562

OAP messages· 563

OAP_CLIENT_DEREG·· 563

OAP_CLIENT_TIMEOUT· 563

OBJP messages· 564

OBJP_ACCELERATE_NO_RES· 564

OBJP_ACCELERATE_NOT_SUPPORT· 564

OBJP_ACCELERATE_UNK_ERR· 565

OFP messages· 566

OFP_ACTIVE· 566

OFP_ACTIVE_FAILED·· 566

OFP_CONNECT· 566

OFP_FAIL_OPEN· 567

OFP_FLOW_ADD·· 567

OFP_FLOW_ADD_ARP_FAILED·· 568

OFP_FLOW_ADD_BUSY· 568

OFP_FLOW_ADD_BUSY_RECOVER· 568

OFP_FLOW_ADD_DUP· 569

OFP_FLOW_ADD_FAILED·· 569

OFP_FLOW_ADD_FAILED·· 570

OFP_FLOW_ADD_ND_FAILED·· 570

OFP_FLOW_ADD_TABLE_MISS· 571

OFP_FLOW_ADD_TABLE_MISS_FAILED·· 571

OFP_FLOW_DEL· 572

OFP_FLOW_DEL_L2VPN_DISABLE· 572

OFP_FLOW_DEL_TABLE_MISS· 573

OFP_FLOW_DEL_TABLE_MISS_FAILED·· 573

OFP_FLOW_DEL_VXLAN_DEL· 574

OFP_FLOW_MOD·· 574

OFP_FLOW_MOD_FAILED·· 575

OFP_FLOW_MOD_TABLE_MISS· 575

OFP_FLOW_MOD_TABLE_MISS_FAILED·· 576

OFP_FLOW_RMV_GROUP· 576

OFP_FLOW_RMV_HARDTIME· 576

OFP_FLOW_RMV_IDLETIME· 577

OFP_FLOW_RMV_METER· 577

OFP_FLOW_UPDATE_FAILED·· 578

OFP_GROUP_ADD·· 578

OFP_GROUP_ADD_FAILED·· 579

OFP_GROUP_DEL· 579

OFP_GROUP_MOD·· 580

OFP_GROUP_MOD_FAILED·· 580

OFP_GROUP_REFRESH_FAILED·· 581

OFP_GROUP_ROLLBACK_FAILED·· 581

OFP_METER_ADD·· 582

OFP_METER_ADD_FAILED·· 582

OFP_METER_DEL· 583

OFP_METER_MOD·· 583

OFP_METER_MOD_FAILED·· 584

OFP_MISS_RMV_GROUP· 584

OFP_MISS_RMV_HARDTIME· 584

OFP_MISS_RMV_IDLETIME· 585

OFP_MISS_RMV_METER· 585

OFP_RADARDETECTION· 585

PORT_MOD·· 586

OPENSRC (FreeRADIUS) messages· 587

HUP event 587

Process restart event 588

Process start event 588

User authentication· 589

OPTMOD messages· 592

BIAS_HIGH· 592

BIAS_LOW·· 592

BIAS_NORMAL· 593

CFG_ERR· 593

CHKSUM_ERR· 593

IO_ERR· 594

MOD_ALM_OFF· 594

MOD_ALM_ON· 594

MODULE_IN· 595

MODULE_OUT· 595

PHONY_MODULE· 595

RX_ALM_OFF· 596

RX_ALM_ON· 596

RX_POW_HIGH· 596

RX_POW_LOW·· 597

RX_POW_NORMAL· 597

TEMP_HIGH· 597

TEMP_LOW·· 598

TEMP_NORMAL· 598

TX_ALM_OFF· 598

TX_ALM_ON· 599

TX_POW_HIGH· 599

TX_POW_LOW·· 599

TX_POW_NORMAL· 600

TYPE_ERR· 600

VOLT_HIGH· 600

VOLT_LOW·· 601

VOLT_NORMAL· 601

OSPF messages· 602

OSPF_DUP_RTRID_NBR· 602

OSPF_IP_CONFLICT_INTRA· 602

OSPF_LAST_NBR_DOWN· 603

OSPF_MEM_ALERT· 603

OSPF_NBR_CHG·· 604

OSPF_NBR_CHG_REASON· 605

OSPF_RT_LMT· 606

OSPF_RTRID_CHG·· 606

OSPF_RTRID_CONFLICT_INTER· 606

OSPF_RTRID_CONFLICT_INTRA· 607

OSPF_VLINKID_CHG·· 607

OSPFV3 messages· 608

OSPFV3_LAST_NBR_DOWN· 608

OSPFV3_MEM_ALERT· 608

OSPFV3_NBR_CHG·· 609

OSPFV3_RT_LMT· 609

PBB messages· 610

PBB_JOINAGG_WARNING·· 610

PBR messages· 611

PBR_HARDWARE_ERROR· 611

PCE messages· 612

PCE_PCEP_SESSION_CHG·· 612

PEX messages (IRF 3) 613

PEX_ASSOCIATEID_MISMATCHING·· 613

PEX_CONFIG_ERROR· 613

PEX_CONNECTION_ERROR· 614

PEX_FORBID_STACK· 614

PEX_LINK_BLOCK· 615

PEX_LINK_DOWN· 616

PEX_LINK_FORWARD·· 616

PEX_REG_JOININ· 617

PEX_REG_LEAVE· 617

PEX_REG_REQUEST· 618

PEX_STACKCONNECTION_ERROR· 618

PEX messages (IRF 3.1) 619

PEX_AUTOCONFIG_BAGG_ASSIGNMEMBER· 619

PEX_AUTOCONFIG_BAGG_CREATE· 619

PEX_AUTOCONFIG_BAGG_NORESOURCE· 620

PEX_AUTOCONFIG_BAGG_REMOVEMEMBER· 621

PEX_AUTOCONFIG_CAPABILITY_ENABLE· 621

PEX_AUTOCONFIG_CASCADELIMIT· 621

PEX_AUTOCONFIG_CONNECTION_ERROR· 622

PEX_AUTOCONFIG_DIFFGROUPNUMBER· 622

PEX_AUTOCONFIG_DYNAMICBAGG_STP· 623

PEX_AUTOCONFIG_GROUP_CREATE· 623

PEX_AUTOCONFIG_NONUMBERRESOURCE· 623

PEX_AUTOCONFIG_NOT_CASCADEPORT· 624

PEX_AUTOCONFIG_NUMBER_ASSIGN· 624

PEX_LLDP_DISCOVER· 625

PEX_MEMBERID_EXCEED·· 625

PEX_PECSP_OPEN_RCVD·· 625

PEX_PECSP_OPEN_SEND·· 626

PEX_PECSP_TIMEOUT· 626

PFILTER messages· 627

PFILTER_GLB_IPV4_DACT_NO_RES· 627

PFILTER_GLB_IPV4_DACT_UNK_ERR· 627

PFILTER_GLB_IPV6_DACT_NO_RES· 628

PFILTER_GLB_IPV6_DACT_UNK_ERR· 628

PFILTER_GLB_MAC_DACT_NO_RES· 629

PFILTER_GLB_MAC_DACT_UNK_ERR· 629

PFILTER_GLB_NO_RES· 630

PFILTER_GLB_NOT_SUPPORT· 630

PFILTER_GLB_ RES_CONFLICT· 631

PFILTER_GLB_UNK_ERR· 631

PFILTER_IF_IPV4_DACT_NO_RES· 632

PFILTER_IF_IPV4_DACT_UNK_ERR· 632

PFILTER_IF_IPV6_DACT_NO_RES· 633

PFILTER_IF_IPV6_DACT_UNK_ERR· 633

PFILTER_IF_MAC_DACT_NO_RES· 634

PFILTER_IF_MAC_DACT_UNK_ERR· 634

PFILTER_IF_NO_RES· 635

PFILTER_IF_NOT_SUPPORT· 635

PFILTER_IF_RES_CONFLICT· 636

PFILTER_IF_UNK_ERR· 636

PFILTER_IPV4_FLOW_INFO·· 637

PFILTER_IPV4_FLOW_STATIS· 637

PFILTER_IPV6_FLOW_INFO·· 638

PFILTER_IPV6_FLOW_STATIS· 638

PFILTER_IPV6_STATIS_INFO·· 639

PFILTER_MAC_FLOW_INFO·· 639

PFILTER_STATIS_INFO·· 640

PFILTER_VLAN_IPV4_DACT_NO_RES· 640

PFILTER_VLAN_IPV4_DACT_UNK_ERR· 641

PFILTER_VLAN_IPV6_DACT_NO_RES· 641

PFILTER_VLAN_IPV6_DACT_UNK_ERR· 642

PFILTER_VLAN_MAC_DACT_NO_RES· 642

PFILTER_VLAN_MAC_DACT_UNK_ERR· 643

PFILTER_VLAN_NO_RES· 643

PFILTER_VLAN_NOT_SUPPORT· 644

PFILTER_VLAN_RES_CONFLICT· 644

PFILTER_VLAN_UNK_ERR· 645

PIM messages· 646

PIM_NBR_DOWN· 646

PIM_NBR_UP· 646

PING messages· 647

PING_STATISTICS· 647

PING_VPN_STATISTICS· 648

PKG messages· 649

PKG_BOOTLOADER_FILE_FAILED·· 649

PKG_BOOTLOADER_FILE_SUCCESS· 649

PKG_INSTALL_ACTIVATE_FAILED·· 649

PKG_INSTALL_ACTIVATE_SUCCESS· 650

PKI messages· 651

GET_CERT_FROM_CA_SERVER_FAIL· 651

IMPORT_CERT_FAIL· 652

REQUEST_CERT_FAIL· 653

REQUEST_CERT_SUCCESS· 654

RETRIEVE_CRL_FAIL· 655

VALIDATE_CERT_FAIL· 656

PKT2CPU messages· 658

PKT2CPU_NO_RESOURCE· 658

PKTCPT· 659

PKTCPT_AP_OFFLINE· 659

PKTCPT_AREADY_EXIT· 659

PKTCPT_CONN_FAIL· 660

PKTCPT_INVALID_FILTER· 660

PKTCPT_LOGIN_DENIED·· 660

PKTCPT_MEMORY_ALERT· 661

PKTCPT_OPEN_FAIL· 661

PKTCPT_OPERATION_TIMEOUT· 661

PKTCPT_SERVICE_FAIL· 662

PKTCPT_UNKNOWN_ERROR· 662

PKTCPT_UPLOAD_ERROR· 663

PKTCPT_WRITE_FAIL· 663

PoE messages· 664

POE_AI_CLEAR· 664

POE_AI_DETECTIONMODE_NONE· 664

POE_AI_DETECTIONMODE_SIMPLE· 665

POE_AI_DISCONNECT_AC· 665

POE_AI_DISCONNECT_DELAY· 665

POE_AI_FORCE_PoE· 666

POE_AI_HIGH_INRUSH· 666

POE_AI_LEGACY· 666

POE_AI_MAXPOWER· 667

POE_AI_RESTART· 667

Portal messages· 668

PORTAL_RULE_FAILED·· 668

PORTSEC messages· 669

PORTSEC_ACL_FAILURE· 669

PORTSEC_CAR_FAILURE· 669

PORTSEC_CREATEAC_FAILURE· 670

PORTSEC_LEARNED_MACADDR· 670

PORTSEC_NTK_NOT_EFFECTIVE· 671

PORTSEC_PORTMODE_NOT_EFFECTIVE· 671

PORTSEC_PROFILE_FAILURE· 672

PORTSEC_URL_FAILURE· 672

PORTSEC_VIOLATION· 673

PORTSEC_VLANMACLIMIT· 673

PPP messages· 674

IPPOOL_ADDRESS_EXHAUSTED·· 674

PPP_USER_LOGON_SUCCESS· 674

PPP_USER_LOGON_FAILED·· 675

PPP_USER_LOGOFF· 675

PTP messages· 677

PTP_MASTER_CLOCK_CHANGE· 677

PTP_PKTLOST· 678

PTP_PKTLOST_RECOVER· 679

PTP_PORT_BMCINFO_CHANGE· 679

PTP_PORT_STATE_CHANGE· 680

PTP_SRC_CHANGE· 681

PTP_SRC_SWITCH· 682

PTP_TIME_LOCK· 682

PTP_TIME_NOT_LOCK· 683

PTS·· 684

PTS_AK_AUTH_FAILED·· 684

PTS_AK_INVALID·· 684

PTS_AK_NO_CERT· 684

PTS_AK_NO_EXIST· 685

PTS_AK_NO_LOAD·· 685

PTS_BTW_PCR_FAILED·· 685

PTS_CHECK_RM_VERSION_FAILED·· 686

PTS_CREATE_AGED_TIMER_FAILED·· 686

PTS_CREATE_CHECK_TIMER_FAILED·· 686

PTS_CREATE_CONTEXT_FAILED·· 687

PTS_CREATE_EPOLL_FAILED·· 687

PTS_CREATE_HASH_FAILED·· 687

PTS_CREATE_SELFVERIFY_COUNTER_FAILED·· 688

PTS_CREATE_SELFVERIFY_TIMER_FAILED·· 688

PTS_CREATE_SOCKET_FAILED·· 688

PTS_CREATE_TIMER_FAILED·· 689

PTS_FILE_HASH_FAILED·· 689

PTS_LOAD_KEY_FAILED·· 689

PTS_PARSE_IML_FAILED·· 690

PTS_PKG_PCR_FAILED·· 690

PTS_READ_PCR_FAILED·· 690

PTS_RM_FILE_FAILED·· 691

PTS_RUNTIME_PCR_FAILED·· 691

PTS_SELFVERIFY_FAILED·· 691

PTS_SELFVERIFY_START_FAILED·· 692

PTS_TEMPLATE_HASH_FAILED·· 692

PWDCTL messages· 693

PWDCTL_ADD_BLACKLIST· 693

PWDCTL_CHANGE_PASSWORD·· 693

PWDCTL_FAILED_TO_WRITEPWD·· 694

PWDCTL_FAILED_TO_OPENFILE· 694

PWDCTL_NOENOUGHSPACE· 694

PWDCTL_NOTFOUNDUSER· 695

PWDCTL_UPDATETIME· 695

QOS messages· 696

MIRROR_SYNC_CFG_FAIL· 696

QOS_CAR_APPLYUSER_FAIL· 696

QOS_CBWFQ_REMOVED·· 697

QOS_GTS_APPLYUSER_FAIL· 697

QOS_IFA_CONFIG_FAIL· 698

QOS_IFA_REFRESH_FAIL· 698

QOS_LR_APPLYIF_FAIL· 698

QOS_NOT_ENOUGH_BANDWIDTH· 699

QOS_NOT_ENOUGH_NNIBANDWIDTH· 699

QOS_POLICY_APPLYCOPP_CBFAIL· 700

QOS_POLICY_APPLYCOPP_FAIL· 700

QOS_POLICY_APPLYGLOBAL_CBFAIL· 701

QOS_POLICY_APPLYGLOBAL_FAIL· 701

QOS_POLICY_APPLYIF_CBFAIL· 702

QOS_POLICY_APPLYIF_FAIL· 702

QOS_POLICY_APPLYUSER_FAIL· 703

QOS_POLICY_APPLYVLAN_CBFAIL· 703

QOS_POLICY_APPLYVLAN_FAIL· 704

QOS_QMPROFILE_APPLYIF_FAIL· 704

QOS_QMPROFILE_APPLYUSER_FAIL· 705

QOS_QMPROFILE_MODIFYQUEUE_FAIL· 705

QOS_QUEUE_APPLYIF_FAIL· 706

QOS_UNI_RESTORE_FAIL· 706

WRED_TABLE_CFG_FAIL· 707

RADIUS messages· 708

RADIUS_ACCT_SERVER_DOWN· 708

RADIUS_ACCT_SERVER_UP· 708

RADIUS_AUTH_FAILURE· 709

RADIUS_AUTH_SERVER_DOWN· 709

RADIUS_AUTH_SERVER_UP· 710

RADIUS_AUTH_SUCCESS· 710

RADIUS_REMOVE_SERVER_FAIL· 710

RDDC messages· 711

RDDC_ACTIVENODE_CHANGE· 711

RESMON·· 712

RESMON_MINOR· 712

RESMON_MINOR_RECOVERY· 713

RESMON_SEVERE· 713

RESMON_SEVERE_RECOVERY· 714

RESMON_USEDUP· 714

RESMON_USEDUP_RECOVERY· 715

RIP messages· 716

RIP_MEM_ALERT· 716

RIP_RT_LMT· 716

RIPNG messages· 717

RIPNG_MEM_ALERT· 717

RIPNG_RT_LMT· 717

RM messages· 718

RM_ACRT_REACH_LIMIT· 718

RM_ACRT_REACH_THRESVALUE· 718

RM_THRESHLD_VALUE_REACH· 719

RM_TOTAL_THRESHLD_VALUE_REACH· 719

RPR messages· 720

RPR_EXCEED_MAX_SEC_MAC· 720

RPR_EXCEED_MAX_SEC_MAC_OVER· 720

RPR_EXCEED_MAX_STATION· 721

RPR_EXCEED_MAX_STATION_OVER· 721

RPR_EXCEED_RESERVED_RATE· 721

RPR_EXCEED_RESERVED_RATE_OVER· 722

RPR_IP_DUPLICATE· 722

RPR_IP_DUPLICATE_OVER· 722

RPR_JUMBO_INCONSISTENT· 723

RPR_JUMBO_INCONSISTENT_OVER· 723

RPR_LAGGCONFIG_INCONSISTENT· 723

RPR_LAGGCONFIG_INCONSISTENT_OVER· 724

RPR_MISCABLING·· 724

RPR_MISCABLING_OVER· 724

RPR_PROTECTION_INCONSISTENT· 725

RPR_PROTECTION_INCONSISTENT_OVER· 725

RPR_SEC_MAC_DUPLICATE· 725

RPR_SEC_MAC_DUPLICATE_OVER· 726

RPR_TOPOLOGY_INCONSISTENT· 726

RPR_TOPOLOGY_INCONSISTENT_OVER· 726

RPR_TOPOLOGY_INSTABILITY· 727

RPR_TOPOLOGY_INSTABILITY_OVER· 727

RPR_TOPOLOGY_INVALID·· 727

RPR_TOPOLOGY_INVALID_OVER· 728

RRPP messages· 729

RRPP_RING_FAIL· 729

RRPP_RING_RESTORE· 729

RTM messages· 730

RTM_ENVIRONMENT· 730

RTM_TCL_LOAD_FAILED·· 730

RTM_TCL_MODIFY· 730

RTM_TCL_NOT_EXIST· 731

SAVA messages· 732

SAVA_SET_DRV_FAILED·· 732

SAVA_SPOOFING_DETECTED·· 732

SAVI messages· 733

SAVI_FILTER_ENTRY_ADD·· 733

SAVI_FILTER_ENTRY_DEL· 733

SAVI_SPOOFING_DETECTED·· 734

SCMD messages· 735

PROCESS_ABNORMAL· 735

PROCESS_ACTIVEFAILED·· 736

PROCESS_CORERECORD·· 736

SCM_ABNORMAL_REBOOT· 737

SCM_ABNORMAL_REBOOTMDC· 737

SCM_ABORT_RESTORE· 738

SCM_PROCESS_HEALTHY· 738

SCM_PROCESS_UNHEALTHY· 738

SCM_INSMOD_ADDON_TOOLONG·· 739

SCM_KERNEL_INIT_TOOLONG·· 739

SCM_KILL_PROCESS· 740

SCM_PROCESS_STARTING_TOOLONG·· 741

SCM_PROCESS_STILL_STARTING·· 742

SCM_SKIP_PROCESS· 742

SCRLSP messages· 744

SCRLSP_LABEL_DUPLICATE· 744

SESSION messages· 745

SESSION_IPV4_FLOW·· 746

SESSION_IPV6_FLOW·· 747

SFLOW messages· 749

SFLOW_HARDWARE_ERROR· 749

SHELL messages· 750

SHELL_CMD·· 750

SHELL_CMD_CONFIRM·· 750

SHELL_CMD_EXECUTEFAIL· 751

SHELL_CMD_INPUT· 751

SHELL_CMD_INPUT_TIMEOUT· 751

SHELL_CMD_INVALID_CHARACTER· 752

SHELL_CMD_MATCHFAIL· 752

SHELL_CMDDENY· 753

SHELL_CMDFAIL· 753

SHELL_COMMIT· 753

SHELL_COMMIT_DELAY· 754

SHELL_COMMIT_REDELAY· 754

SHELL_COMMIT_ROLLBACK· 754

SHELL_COMMIT_ROLLBACKDONE· 755

SHELL_COMMIT_WILLROLLBACK· 755

SHELL_CRITICAL_CMDFAIL· 755

SHELL_LOGIN· 756

SHELL_LOGOUT· 756

SLSP messages· 757

SLSP_LABEL_DUPLICATE· 757

SMARTMC messages· 758

ERROR· 758

SMLK messages· 759

SMLK_LINK_SWITCH· 759

SMLK_LINK_SWITCH· 759

SNMP messages· 760

SNMP_ACL_RESTRICTION· 760

SNMP_AUTHENTICATION_FAILURE· 760

SNMP_GET· 761

SNMP_INFORM_LOST· 761

SNMP_NOTIFY· 762

SNMP_SET· 763

SNMP_USM_NOTINTIMEWINDOW·· 763

SSHC messages· 764

SSHC_ALGORITHM_MISMATCH· 764

SSHC_AUTH_PASSWORD_FAIL· 764

SSHC_AUTH_PUBLICKEY_FAIL· 765

SSHC_CERT_VERIFY_FAIL· 766

SSHC_CONNECT_FAIL· 767

SSHC_DECRYPT_FAIL· 767

SSHC_DISCONNECT· 768

SSHC_ENCRYPT_FAIL· 768

SSHC_HOST_NAME_ERROR· 768

SSHC_KEY_EXCHANGE_FAIL· 769

SSHC_MAC_ERROR· 769

SSHC_PUBLICKEY_NOT_EXIST· 769

SSHC_VERSION_MISMATCH· 770

SSHS messages· 771

SSHS_ACL_DENY· 771

SSHS_ALGORITHM_MISMATCH· 771

SSHS_AUTH_EXCEED_RETRY_TIMES· 772

SSHS_AUTH_FAIL· 772

SSHS_AUTH_KBDINT_FAIL· 773

SSHS_AUTH_PWD_FAIL· 773

SSHS_AUTH_TIMEOUT· 773

SSHS_AUTH_SUCCESS· 774

SSHS_AUTHOR_FAIL· 774

SSHS_CERT_VERIFY_FAIL· 775

SSHS_CONNECT· 776

SSHS_DECRYPT_FAIL· 776

SSHS_DISCONNECT· 777

SSHS_ENCRYPT_FAIL· 777

SSHS_LOG·· 778

SSHS_MAC_ERROR· 778

SSHS_REACH_SESSION_LIMIT· 779

SSHS_REACH_USER_LIMIT· 779

SSHS_SCP_OPER· 779

SSHS_SFTP_OPER· 780

SSHS_SRV_UNAVAILABLE· 780

SSHS_VERSION_MISMATCH· 781

STAMGR messages· 782

STAMGR_ADD_FAILVLAN· 782

STAMGR_ADDBAC_INFO·· 782

STAMGR_ADDSTA_INFO·· 782

STAMGR_AUTHORACL_FAILURE· 783

STAMGR_AUTHORUSERPROFILE_FAILURE· 783

STAMGR_CLIENT_OFFLINE· 784

STAMGR_CLIENT_ONLINE· 784

STAMGR_DELBAC_INFO·· 784

STAMGR_DELSTA_INFO·· 785

STAMGR_DOT1X_LOGIN_FAILURE· 785

STAMGR_DOT1X_LOGIN_SUCC· 786

STAMGR_DOT1X_LOGOFF· 786

STAMGR_MACA_LOGIN_FAILURE· 787

STAMGR_MACA_LOGIN_SUCC· 788

STAMGR_MACA_LOGOFF· 788

STAMGR_STAIPCHANGE_INFO·· 789

STAMGR_TRIGGER_IP· 789

STM messages· 790

STM_AUTO_UPDATE_FAILED·· 790

STM_AUTO_UPDATE_FINISHED·· 791

STM_AUTO_UPDATING·· 791

STM_HELLOPKT_NOTSEND·· 792

STM_HELLOPKT_NOTRCV· 792

STM_LINK_DOWN· 792

STM_LINK_TIMEOUT· 793

STM_LINK_UP· 793

STM_MERGE· 793

STM_MERGE_NEED_REBOOT· 794

STM_MERGE_NOT_NEED_REBOOT· 794

STM_SAMEMAC· 794

STM_SOMER_CHECK· 795

STP messages· 796

STP_BPDU_PROTECTION· 796

STP_BPDU_RECEIVE_EXPIRY· 796

STP_CONSISTENCY_CHECK· 797

STP_CONSISTENCY_RESTORATION· 797

STP_DETECTED_TC· 797

STP_DISABLE· 798

STP_DISCARDING·· 798

STP_DISPUTE· 799

STP_DISPUTE_RESTORATION· 799

STP_EDGEPORT_INACTIVE· 800

STP_ENABLE· 800

STP_FORWARDING·· 800

STP_LOOP_PROTECTION· 801

STP_LOOPBACK_PROTECTION· 801

STP_NOT_ROOT· 801

STP_NOTIFIED_TC· 802

STP_PORT_TYPE_INCONSISTENCY· 802

STP_PVID_INCONSISTENCY· 802

STP_PVST_BPDU_PROTECTION· 803

STP_ROOT_PROTECTION· 803

STP_STG_NUM_DETECTION· 803

SYSLOG messages· 805

SYSLOG_DISABLE· 805

SYSLOG_ENABLE· 805

SYSLOG_LOGBUFFER_FAILURE· 805

SYSLOG_LOGFILE_CREATE· 806

SYSLOG_LOGFILE_FULL· 806

SYSLOG_LOGFILE_OVERWRITE· 806

SYSLOG_NO_SPACE· 807

SYSLOG_RESTART· 807

SYSLOG_RTM_EVENT_BUFFER_FULL· 807

TACACS messages· 808

TACACS_ACCT_SERVER_DOWN· 808

TACACS_ACCT_SERVER_UP· 808

TACACS_AUTH_FAILURE· 809

TACACS_AUTH_SERVER_DOWN· 809

TACACS_AUTH_SERVER_UP· 810

TACACS_AUTH_SUCCESS· 810

TACACS_AUTHOR_SERVER_DOWN· 811

TACACS_AUTHOR_SERVER_UP· 811

TACACS_REMOVE_SERVER_FAIL· 812

TCSM·· 813

TCSM_CERT_BROKEN· 813

TCSM_KEY_BROKEN· 813

TCSM_KEY_HIERARCHY_BROKEN· 813

TCSM_TSS_SVC_DOWN· 814

TCSM_TSS_SVC_UP· 814

TELNETD messages· 815

TELNETD_ACL_DENY· 815

TELNETD_REACH_SESSION_LIMIT· 815

TRACK messages· 816

TRACK_STATE_CHANGE· 816

TRILL messages· 817

TRILL_DUP_SYSTEMID·· 817

TRILL_INTF_CAPABILITY· 817

TRILL_LICENSE_EXPIRED·· 818

TRILL_LICENSE_EXPIRED_TIME· 818

TRILL_LICENSE_UNAVAILABLE· 818

TRILL_MEM_ALERT· 819

TRILL_NBR_CHG·· 819

VCF messages· 820

VCF_AGGR_CREAT· 820

VCF_AGGR_DELETE· 820

VCF_AGGR_FAILED·· 821

VCF_AUTO_ANALYZE_USERDEF· 821

VCF_AUTO_NO_USERDEF· 822

VCF_AUTO_START· 822

VCF_AUTO_STATIC_CMD·· 823

VCF_BGP· 824

VCF_DOWN_LINK· 825

VCF_DRIVER_INIT· 825

VCF_FAILED_ADD_IRFPORT· 826

VCF_GET_IMAGE· 826

VCF_GET_TEMPLATE· 827

VCF_INSTALL_IMAGE· 827

VCF_IRF_FINISH· 828

VCF_IRF_FOUND·· 828

VCF_IRF_START· 829

VCF_LOOPBACK_START· 829

VCF_LOOPBACK_START_FAILED·· 830

VCF_LOOPBACK_ALLOC· 830

VCF_LOOPBACK_NO_FREE_IP· 831

VCF_LOOPBACK_RECLAIM·· 831

VCF_REBOOT· 832

VCF_SKIP_INSTALL· 832

VCF_STATIC_CMD_ERROR· 833

VCF_UP_LINK· 833

VCF_WHITE_LIST_CHECK· 834

VLAN messages· 835

VLAN_CREATEFAIL· 835

VLAN_FAILED·· 835

VLAN_QINQETHTYPE_FAILED·· 836

VLAN_VLANMAPPING_FAILED·· 836

VLAN_VLANTRANSPARENT_FAILED·· 837

VRRP messages· 838

VRRP_STATUS_CHANGE· 838

VRRP_VF_STATUS_CHANGE· 839

VRRP_VMAC_INEFFECTIVE· 839

VSRP messages· 840

VSRP_BIND_FAILED·· 840

VXLAN messages· 841

VXLAN_LICENSE_UNAVAILABLE· 841

WEB messages· 842

LOGIN· 842

LOGIN_FAILED·· 842

LOGOUT· 842

WIPS messages· 843

APFLOOD·· 843

AP_CHANNEL_CHANGE· 843

ASSOCIATEOVERFLOW·· 843

HONEYPOT· 844

HTGREENMODE· 844

MAN_IN_MIDDLE· 844

WIPS_DOS· 845

WIPS_FLOOD·· 845

WIPS_MALF· 846

WIPS_SPOOF· 847

WIPS_WEAKIV· 847

WIRELESSBRIDGE· 848

 


Introduction

This document includes the following system messages:

·     Messages specific to Release 65xx of the switch.

·     Messages for the Comware 7 software platform version based on which Release 65xx was produced. Some platform system messages might not be available on the switch.

This document is intended only for managing H3C Campus Fixed-Port Switches. Do not use this document for any other device models.

This document assumes that the readers are familiar with data communications technologies and H3C networking products.

System log message format

By default, the system log messages use one of the following formats depending on the output destination:

·     Log host:

<PRI>TIMESTAMP Sysname %%vendorMODULE/severity/MNEMONIC: location; CONTENT

·     Destinations except for the log host:

Prefix TIMESTAMP Sysname MODULE/severity/MNEMONIC: CONTENT

 

 

NOTE:

Log message examples in this document use the format for destinations except the log host. They do not contain elements available only for the log host, including the location element.

 

Table 1 System log message elements

Element

Description

<PRI>

Priority identifier. This element is contained only in messages sent to the log host.

It is calculated by using the following formula:

Priority identifier=facilityx8+severity

Where:

·     Facility is specified by using the info-center loghost command. A log host uses this parameter to identify log sources and filter log messages.

·     Severity represents the importance of the message. For more information about severity levels, see Table 2.

Prefix

Message type identifier. This element is contained in the system log messages sent to non-log-host destinations.

The element uses the following symbols to indicate message severity:

·     Percentage sign (%)—Informational and higher levels.

·     Asterisk (*)—Debug level.

TIMESTAMP

Date and time when the event occurred.

The following are commands for configuring the timestamp format:

·     Log host—Use the info-center timestamp loghost command.

·     Non-log-host destinations—Use the info-center timestamp command.

Sysname

Name or IP address of the device that generated the message.

%%vendor

Manufacturer flag. This element is %%10 for H3C.

This element is only available in messages sent to the log host.

MODULE

Name of the module that produced the message.

severity

Severity level of the message. (For more information about severity levels, see Table 2.)

MNEMONIC

Text string that uniquely identifies the system message. The maximum length is 32 characters.

location

Optional. This element identifies where the message occurred. This element is contained only in messages sent to the log host.

This element presents location information for the message in the following format:

-attribute1=x-attribute2=y…-attributeN=z

The following are examples of location attributes:

·     -MDC=XX, which represents the MDC on which the message occurred.

·     -DevIp=XXX.XXX.XXX.XXX, which represents the source IP of the message.

·     -Slot=XX, which represents the slot on which the message occurred.

·     -Chassis=XX-Slot=XX, which represents the chassis and slot on which the message occurred.

This element is separated from the message description by using a semicolon (;).

CONTENT

Text string that contains detailed information about the event or error.

For variable fields in this element, this document uses the representations in Table 3.

 

System log messages are classified into eight severity levels from 0 to 7. The lower the number, the higher the severity, as shown in Table 2.

Table 2 System log message severity levels

Level

Severity

Description

0

Emergency

The system is unusable. For example, the system authorization has expired.

1

Alert

Action must be taken immediately. For example, traffic on an interface exceeds the upper limit.

2

Critical

Critical condition. For example, the device temperature exceeds the upper limit, the power module fails, or the fan tray fails.

3

Error

Error condition. For example, the link state changes or a storage card is unplugged.

4

Warning

Warning condition. For example, an interface is disconnected, or the memory resources are used up.

5

Notification

Normal but significant condition. For example, a terminal logs in to the device, or the device reboots.

6

Informational

Informational message. For example, a command or a ping operation is executed.

7

Debug

Debugging message.

 

For variable fields in the message text, this document uses the representations in Table 3. The values are case insensitive, even though the representations are uppercase letters.

Table 3 Variable field representations

Representation

Information type

INT16

Signed 16-bit decimal number.

UINT16

Unsigned 16-bit decimal number.

INT32

Signed 32-bit decimal number.

UINT32

Unsigned 32-bit decimal number.

INT64

Signed 64-bit decimal number.

UINT64

Unsigned 64-bit decimal number.

DOUBLE

Two dot-separated signed 32-bit decimal numbers. The format is [INTEGER].[INTEGER].

HEX

Hexadecimal number.

CHAR

Single character.

STRING

Character string.

IPADDR

IP address.

MAC

MAC address.

DATE

Date.

TIME

Time.

 

Managing and obtaining system log messages

You can manage system log messages by using the information center.

By default, the information center is enabled. Log messages can be output to the console, monitor terminal, log buffer, log host, and log file.

To filter log messages, use the info-center source command to specify log output rules. A log output rule specifies the source modules and the lowest severity level of log messages that can be output to a destination. A log message is output if its severity level is higher than or equal to the specified level. For example, if you specify a severity level of 6 (informational), log messages that have a severity level from 0 to 6 are output.

For more information about using the information center, see the network management and monitoring configuration guide for the product.

Obtaining log messages from the console terminal

Access the device through the console port. Real-time log messages are displayed on the console terminal.

Obtaining log messages from a monitor terminal

Monitor terminals refer to terminals that access the device through the AUX, VTY, or TTY lines (for example, Telnet). To obtain log messages from a monitor terminal, use the following guidelines:

·     To display log messages on the monitor terminal, you must configure the terminal monitor command.

·     For monitor terminals, the lowest level of log messages that can be displayed is determined by both the terminal logging level and info-center source commands.

 

 

NOTE:

Settings for the terminal monitor and terminal logging level commands take effect only on the current login session. The default settings for the commands restore at a relogin.

 

Obtaining log messages from the log buffer

Use the display logbuffer command to display history log messages in the log buffer.

Obtaining log messages from the log file

By default, the log file feature automatically saves logs from the log file buffer to the log file every 24 hours. You can use the info-center logfile frequency command to change the automatic saving internal.

To manually save logs to the log file, use the logfile save command. The log file buffer is cleared each time a save operation is performed.

By default, you can obtain the log file from the flash:/logfile path.

To view the contents of the log file on the device, use the more command.

Obtaining log messages from a log host

Use the info-center loghost command to specify the service port number and IP address of a log host. To specify multiple log hosts, repeat the command.

For a successful log message transmission, make sure the specified port number is the same as the port number used on the log host. The default service port number is 514.

Software module list

Table 4 lists all software modules that might produce system log messages. This document uses "OPENSRC" to represent all open source modules.

Table 4 Software module list

Module name representation

Module name expansion

AAA

Authentication, Authorization and Accounting

ACL

Access Control List

ANCP

Access Node Control Protocol

APMGR

Access Point Management

ARP

Address Resolution Protocol

ATK

Attack Detection and Prevention

ATM

Asynchronous Transfer Mode

BFD

Bidirectional Forwarding Detection

BGP

Border Gateway Protocol

BLS

Blacklist

CFD

Connectivity Fault Detection

CFGMAN

Configuration Management

CONNLMT

Connection Limit

DEV

Device Management

DHCP

Dynamic Host Configuration Protocol

DHCPR

IPv4 DHCP Relay

DHCPS

DHCP Server

DHCPS6

DHCPv6 Server

DHCPSP4

DHCP Snooping

DHCPSP6

DHCPv6 Snooping

DIAG

Diagnosis

DLDP

Device Link Detection Protocol

DOT1X

802.1X

DRNI

Distributed Resilient Network Interconnect

DRVPLAT

Drive Platform

EDEV

Extended-Device Management

EPA

Endpoint Analysis

ERPS

Ethernet Ring Protection Switching

ETH

Ethernet

ETHDRNI

Ethernet Distributed Resilient Network Interconnect

ETHOAM

Ethernet Operation, Administration and Maintenance

EVB

Edge Virtual Bridging

EVIISIS

Ethernet Virtual Interconnect Intermediate System-to-Intermediate System

FCOE

Fibre Channel Over Ethernet

FCLINK

Fibre Channel Link

FCZONE

Fibre Channel Zone

FIB

Forwarding Information Base

FILTER

Filter

FIPSNG

FIP Snooping

FS

File System

FTP

File Transfer Protocol

gRPC

Google Remote Procedure Call

HA

High Availability

HLTH

Health

HQOS

Hierarchical QoS

HTTPD

Hypertext Transfer Protocol Daemon

IFNET

Interface Net Management

IKE

Internet Key Exchange

IMA

Integrity Measurements Architecture

iNQA

Intelligent Network Quality Analyzer

IP6ADDR

IPv6 Addressing

IP6FW

IPv6 Forwarding

IPADDR

IP Addressing

IPFW

IP Forwarding

IPSEC

IP Security

IPSG

IP Source Guard

IRDP

ICMP Router Discovery Protocol

IRF

Intelligent Resilient Framework

ISIS

Intermediate System-to-Intermediate System

ISSU

In-Service Software Upgrade

L2PT

Layer 2 Protocol Tunneling

L2TPV2

Layer 2 Tunneling Protocol Version 2

L2VPN

Layer 2 VPN

LAGG

Link Aggregation

LDP

Label Distribution Protocol

LIPC

Leopard Inter-process Communication

LLDP

Link Layer Discovery Protocol

LOAD

Load Management

LOGIN

Login

LPDT

Loopback Detection

LS

Local Server

LSPV

LSP Verification

MAC

Media Access Control

MACA

MAC Authentication

MACSEC

MAC Security

MBFD

MPLS BFD

MBUF

Memory buffer

MDC

Multitenant Device Context

MFIB

Multicast Forwarding Information Base

MGROUP

Mirroring group

MPLS

Multiprotocol Label Switching

MTLK

Monitor Link

NAT

Network Address Translation

NETCONF

Network Configuration Protocol

ND

Neighbor Discovery

NQA

Network Quality Analyzer

NSS

Session-based NetStream

NTP

Network Time Protocol

OAP

Open Application Platform

OPENSRC (FreeRADIUS)

Open Source

OBJP

Object Policy

OFP

OpenFlow Protocol

OPTMOD

Optical Module

OSPF

Open Shortest Path First

OSPFV3

Open Shortest Path First Version 3

PFILTER

Packet Filter

PBB

Provider Backbone Bridge

PBR

Policy-Based Routing

PCE

Path Computation Element

PEX

Port Extender

PIM

Protocol Independent Multicast

PING

Packet Internet Groper

PKG

Package

PKI

Public Key Infrastructure

PKT2CPU

Packet to CPU

PKTCPT

Packet Capture

PoE

Power over Ethernet

PORTAL

Portal

PORTSEC

Port Security

PPP

Point to Point Protocol

PTP

Precision Time Protocol

PTS

Platform Trust Services

PWDCTL

Password Control

QOS

Quality of Service

RADIUS

Remote Authentication Dial In User Service

RESMON

Resource Monitor

RDDC

Redundancy

RIP

Routing Information Protocol

RIPNG

Routing Information Protocol Next Generation

RM

Routing Management

RPR

Resilient Packet Ring

RRPP

Rapid Ring Protection Protocol

RTM

Real-Time Event Manager

SCMD

Service Control Manager Daemon

SCRLSP

Static CRLSP

SESSION

Session

SFLOW

Sampler Flow

SHELL

Shell

SLSP

Static LSP

SMARTMC

Smart Management Center

SMLK

Smart Link

SNMP

Simple Network Management Protocol

SQA

Service Quality Analysis

SSHC

Secure Shell Client

SSHS

Secure Shell Server

STAMGR

Station Management

STM

Stack Topology Management

STP

Spanning Tree Protocol

SYSEVENT

System Event

SYSLOG

System Log

TACACS

Terminal Access Controller Access Control System

TCSM

Trusted Computing Services Management

TELNETD

Telnet Daemon

TRILL

Transparent Interconnect of Lots of Links

VCF

Vertical Converged Framework

VLAN

Virtual Local Area Network

VRRP

Virtual Router Redundancy Protocol

VSRP

Virtual Service Redundancy Protocol

VXLAN

Virtual eXtensible LAN

WEB

Web

WIPS

Wireless Intrusion Prevention System

 

Using this document

This document categorizes system log messages by software module. The modules are ordered alphabetically. Except for OPENSRC, the system log messages for each module are listed in alphabetic order of their mnemonic names. The OPENSRC messages are unordered because they use the same mnemonic name (SYSLOG). For each OPENSRC message, the section title uses a short description instead of the mnemonic name.

This document explains messages in tables. Table 5 describes information provided in these tables.

Table 5 Message explanation table contents

Item

Content

Example

Message text

Presents the message description.

ACL [UINT32] [STRING] [UINT64] packet(s).

Variable fields

Briefly describes the variable fields in the order that they appear in the message text.

The variable fields are numbered in the "$Number" form to help you identify their location in the message text.

$1: ACL number.

$2: ID and content of an ACL rule.

$3: Number of packets that matched the rule.

Severity level

Provides the severity level of the message.

6

Example

Provides a real message example. The examples do not include the "<PRI>TIMESTAMP Sysname %%vendor" part or the "Prefix TIMESTAMP Sysname" part, because information in this part varies with system settings.

ACL/6/ACL_STATIS_INFO: ACL 2000 rule 0 permit source 1.1.1.1 0 logging 10000 packet(s).

Explanation

Explains the message, including the event or error cause.

Number of packets that matched an ACL rule. This message is sent when the packet counter changes.

Recommended action

Provides recommended actions. For informational messages, no action is required.

No action is required.

 


AAA messages

This section contains AAA messages.

AAA_FAILURE

Message text

-AAAType=[STRING]-AAADomain=[STRING]-Service=[STRING]-UserName=[STRING]; AAA failed.

Variable fields

$1: AAA type.

$2: AAA scheme.

$3: Service.

$4: Username.

Severity level

5

Example

AAA/5/AAA_FAILURE: -AAAType=AUTHOR-AAADomain=domain1-Service=login-UserName=cwf@system; AAA failed.

Explanation

An AAA request was rejected.

The following are the common reasons:

·     No response was received from the server.

·     The username or password was incorrect.

·     The service type that the user applied for was incorrect.

Recommended action

1.     Verify that the device is correctly connected to the server.

2.     Enter the correct username and password.

3.     Verify that the server settings are the same as the settings on the device.

4.     If the problem persists, contact H3C Support.

 

AAA_LAUNCH

Message text

-AAAType=[STRING]-AAADomain=[STRING]-Service=[STRING]-UserName=[STRING]; AAA launched.

Variable fields

$1: AAA type.

$2: AAA scheme.

$3: Service.

$4: Username.

Severity level

6

Example

AAA/6/AAA_LAUNCH: -AAAType=AUTHEN-AAADomain=domain1-Service=login-UserName=cwf@system; AAA launched.

Explanation

An AAA request was received.

Recommended action

No action is required.

 

AAA_SUCCESS

Message text

-AAAType=[STRING]-AAADomain=[STRING]-Service=[STRING]-UserName=[STRING]; AAA succeeded.

Variable fields

$1: AAA type.

$2: AAA scheme.

$3: Service.

$4: Username.

Severity level

6

Example

AAA/6/AAA_SUCCESS: -AAAType=AUTHOR-AAADomain=domain1-Service=login-UserName=cwf@system; AAA succeeded.

Explanation

An AAA request was accepted.

Recommended action

No action is required.

 


ACL messages

This section contains ACL messages.

ACL_ACCELERATE_NO_RES

Message text

Failed to accelerate [STRING] ACL [UINT32]. The resources are insufficient.

Variable fields

$1: ACL type.

$2: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NO_RES: Failed to accelerate IPv6 ACL 2001. The resources are insufficient.

Explanation

Hardware resources were insufficient for accelerating an ACL.

Recommended action

Delete some rules or disabled ACL acceleration for other ACLs to release hardware resources.

 

ACL_ACCELERATE_NONCONTIGUOUSMASK

Message text

Failed to accelerate ACL [UINT32]. ACL acceleration supports only contiguous wildcard masks.

Variable fields

$1: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NONCONTIGUOUSMASK: Failed to accelerate ACL 2001. ACL acceleration supports only contiguous wildcard masks.

Explanation

ACL acceleration failed because rules containing noncontiguous wildcard masks exist in the ACL.

Recommended action

Check the ACL rules and delete the unsupported configuration.

 

ACL_ACCELERATE_NOT_SUPPORT

Message text

Failed to accelerate [STRING] ACL [UINT32]. The operation is not supported.

Variable fields

$1: ACL type.

$2: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NOT_SUPPORT: Failed to accelerate IPv6 ACL 2001. The operation is not supported.

Explanation

ACL acceleration failed because the system does not support ACL acceleration.

Recommended action

No action is required.

 

ACL_ACCELERATE_NOT_SUPPORTHOPBYHOP

Message text

Failed to accelerate IPv6 ACL [UINT32]. ACL acceleration does not support the rules that contain the hop-by-hop keywords.

Variable fields

$1: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NOT_SUPPORTHOPBYHOP: Failed to accelerate IPv6 ACL 2001. ACL acceleration does not support the rules that contain the hop-by-hop keywords.

Explanation

ACL acceleration failed for the IPv6 ACL because rules containing the hop-by-hop keyword exist in the ACL.

Recommended action

Check the ACL rules and delete the unsupported configuration.

 

ACL_ACCELERATE_NOT_SUPPORTMULTITCPFLAG

Message text

Failed to accelerate IPv6 ACL [UINT32]. ACL acceleration does not support specifying multiple TCP flags in one rule.

Variable fields

$1: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NOT_SUPPORTMULTITCPFLAG: Failed to accelerate IPv6 ACL 2001. ACL acceleration does not support specifying multiple TCP flags in one rule.

Explanation

ACL acceleration failed for the IPv6 ACL because rules containing multiple TCP flags exist in the ACL.

Recommended action

Check the ACL rules and delete the unsupported configuration.

 

ACL_ACCELERATE_UNK_ERR

Message text

Failed to accelerate [STRING] ACL [UINT32].

Variable fields

$1: ACL type.

$2: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_UNK_ERR: Failed to accelerate IPv6 ACL 2001.

Explanation

ACL acceleration failed because of an unknown error.

Recommended action

No action is required.

 

ACL_IPV6_STATIS_INFO

Message text

IPv6 ACL [UINT32] [STRING] [UINT64] packet(s).

Variable fields

$1: ACL number.

$2: ID and content of an IPv6 ACL rule.

$3: Number of packets that matched the rule.

Severity level

6

Example

ACL/6/ACL_IPV6_STATIS_INFO: IPv6 ACL 2000 rule 0 permit source 1:1::/64 logging 1000 packet(s).

Explanation

The number of packets matching the IPv6 ACL rule changed.

Recommended action

No action is required.

 

ACL_NO_MEM

Message text

Failed to configure [STRING] ACL [UINT] due to lack of memory.

Variable fields

$1: ACL type.

$2: ACL number.

Severity level

3

Example

ACL/3/ACL_NO_MEM: Failed to configure ACL 2001 due to lack of memory.

Explanation

Configuring the ACL failed because memory is insufficient.

Recommended action

Use the display memory-threshold command to check the memory usage.

 

ACL_STATIS_INFO

Message text

ACL [UINT32] [STRING] [UINT64] packet(s).

Variable fields

$1: ACL number.

$2: ID and content of an IPv4 ACL rule.

$3: Number of packets that matched the rule.

Severity level

6

Example

ACL/6/ACL_STATIS_INFO: ACL 2000 rule 0 permit source 1.1.1.1 0 logging 10000 packet(s).

Explanation

The number of packets matching the IPv4 ACL rule changed.

Recommended action

No action is required.

 

 


ANCP messages

This section contains ANCP messages.

ANCP_INVALID_PACKET

Message text

-NeighborName=[STRING]-State=[STRING]-MessageType=[STRING]; The [STRING] value [STRING] is wrong, and the value [STRING] is expected.

Variable fields

$1: ANCP neighbor name.

$2: Neighbor state.

$3: Message type.

$4: Field.

$5: Wrong value of the field.

$6: Expected value of the field.

Severity level

6

Example

ANCP/6/ANCP_INVALID_PACKET: -NeighborName=Dslam-State=SYNSENT-MessageType=SYNACK; The Sender Instance value 0 is wrong, and the value 1 is expected.

Explanation

The system received an adjacency message that had a field with a wrong value.

Recommended action

No action is required.

 

 


APMGR messages

This section contains access point management messages.

APMGR_AC_MEM_ALERT

Message text

The memory utilization has reached the threshold.

Variable fields

N/A

Severity level

4

Example

APMGR/4/APMGR_AC_MEM_ALERT: The memory utilization has reached the threshold.

Explanation

The AP failed to come online because the memory utilization exceeded the limit.

Recommended action

Stop creating manual APs and prevent APs from coming online.

 

APMGR_ADD_AP_FAIL

Message text

AP [STRING] failed to come online using serial ID [STRING]: MAC address [STRING] is being used by AP [STRING].

Variable fields

$1: AP name.

$2: Serial ID.

$3: MAC address.

$4: AP name.

Severity level

4

Example

APMGR/4/ APMGR_ADD_AP_FAIL: AP ap1 failed to come online using serial ID 01247ef96: MAC address 0023-7961-5201 is being used by AP ap2.

Explanation

The AP failed to come online because a manual AP that has the same MAC address already exists on the AC.

Recommended action

Delete either the manual AP that has the MAC address or the serial ID.

 

APMGR_ADDBAC_INFO

Message text

Add BAS AC [STRING].

Variable fields

$1: MAC address of the BAS AC.

Severity level

6

Example

APMGR/6/APMGR_ADDBAC_INFO: Add BAS AC 3ce5-a616-28cd.

Explanation

The BAS AC was connected to the master AC.

Recommended action

No action is required.

 

APMGR_AP_OFFLINE

Message text

AP [STRING] went offline. State changed to Idle.

Variable fields

$1: AP name.

Severity level

6

Example

APMGR/6/APMGR_AP_OFFLINE: AP ap1 went offline. State changed to Idle.

Explanation

The AP went offline. The state of the AP changed to Idle.

Recommended action

If the AP went offline abnormally, check the debugging information to locate the issue and resolve it.

 

APMGR_AP_ONLINE

Message text

AP [STRING] went online. State changed to Run.

Variable fields

$1: AP name.

Severity level

6

Example

APMGR/6/APMGR_AP_ONLINE: AP ap1 went online. State changed to Run.

Explanation

The AP came online. The state of the AP changed to Run.

Recommended action

No action is required.

 

APMGR_CWC_IMG_DOWNLOAD_COMPLETE

Message text

System software image file [STRING] downloading through the CAPWAP tunnel to AC [STRING] completed.

Variable fields

$1: Image file name.

$2: AC IP address.

Severity level

6

Example

APMGR/6/APMGR_CWC_IMG_DOWNLOAD_COMPLETE: System software image file 5800.ipe downloading through the CAPWAP tunnel to AC 192.168.10.1 completed.

Explanation

The AP downloaded the image file from the AC successfully.

Recommended action

No action is required.

 

APMGR_CWC_IMG_DOWNLOAD_START

Message text

Started to download the system software image file [STRING] through the CAPWAP tunnel to AC [STRING].

Variable fields

$1: Image file name.

$2: AC IP address.

Severity level

6

Example

APMGR/6/APMGR_CWC_IMG_DOWNLOAD_START: Started to download the system software image file 5800.ipe through the CAPWAP tunnel to AC 192.168.10.1.

Explanation

The AP started to download the image file from the AC.

Recommended action

Make sure the AP is correctly connected to the AC.

 

APMGR_CWC_IMG_NO_ENOUGH_SPACE

Message text

Insufficient flash memory space for downloading system software image file [STRING].

Variable fields

$1: Image file name.

Severity level

6

Example

APMGR/6/APMGR_CWC_IMG_NO_ENOUGH_SPACE: Insufficient flash memory space for downloading system software image file 5800.ipe.

Explanation

The AP failed to download the image file from the AC because of insufficient flash memory.

Recommended action

Delete files not in use from the AP.

 

APMGR_CWC_LOCAL_AC_DOWN

Message text

CAPWAP tunnel to Central AC [STRING] went down. Reason: [STRING].

Variable fields

$1: IP address of the central AC.

$2: Reason:

·     Added local AC IP address.

·     Deleted local AC IP address.

·     Local AC interface used for CAPWAP tunnel went down.

·     Local AC config changed.

·     N/A

Severity level

4

Example

APMGR/4/APMGR_CWC_LOCAL_AC_DOWN: CAPWAP tunnel to Central AC 2.2.2.1 went down. Reason: Added local AC IP address.

Explanation

The CAPWAP tunnel between the central AC and the local AC was terminated for a specific reason.

Recommended action

To resolve the issue:

1.     Examine the network connection between the central AC and the local AC.

2.     Verify that the central AC is correctly configured.

3.     Verify that the local AC is correctly configured.

4.     If the issue persists, contact H3C Support.

 

APMGR_CWC_LOCAL_AC_UP

Message text

CAPWAP tunnel to Central AC [STRING] went up.

Variable fields

$1: IP address of the central AC.

Severity level

6

Example

APMGR/6/APMGR_CWC_LOCAL_AC_UP: CAPWAP tunnel to Central AC 2.2.2.1 went up.

Explanation

The central AC has established a CAPWAP tunnel with the local AC.

Recommended action

No action is required.

 

APMGR_CWC_REBOOT

Message text

AP in state [STRING] is rebooting. Reason: [STRING]

Variable fields

$1: AP state.

$2: Reason:

·     AP was reset.

·     Image was downloaded successfully.

·     AP stayed in idle state for a long time.

Severity level

6

Example

APMGR/6/APMGR_CWC_REBOOT: AP in State Run is rebooting. Reason: AP was reset.

Explanation

The AP rebooted for a specific reason.

Recommended action

No action is required.

 

APMGR_CWC_RUN_DOWNLOAD_COMPLETE

Message text

File [STRING] successfully downloaded through the CAPWAP tunnel to AC [STRING].

Variable fields

$1: File name.

$2: AC IP address.

Severity level

6

Example

APMGR/6/APMGR_CWC_RUN_DOWNLOAD_COMPLETE: File ac.cfg successfully downloaded through the CAPWAP tunnel to AC 192.168.10.1.

Explanation

The AP downloaded the file from the AC successfully.

Recommended action

No action is required.

 

APMGR_CWC_RUN_DOWNLOAD_START

Message text

Started to download the file [STRING] through the CAPWAP tunnel to AC [STRING].

Variable fields

$1: File name.

$2: AC IP address.

Severity level

6

Example

APMGR/6/APMGR_CWC_RUN_DOWNLOAD_START: Started to download the file ac.cfg through the CAPWAP tunnel to AC 192.168.10.1.

Explanation

The AP started to download the file from the AC.

Recommended action

Make sure the AP is correctly connected to the AC.

 

APMGR_CWC_RUN_NO_ENOUGH_SPACE

Message text

Insufficient flash memory space for downloading file [STRING].

Variable fields

$1: File name.

Severity level

6

Example

APMGR/6/APMGR_CWC_RUN_NO_ENOUGH_SPACE: Insufficient flash memory space for downloading file ac.cfg.

Explanation

The AP failed to download the file from the AC because of insufficient flash memory.

Recommended action

Delete files not in use from the AP.

 

APMGR_CWC_TUNNEL_DOWN

Message text

CAPWAP tunnel to AC [STRING] went down. Reason: [STRING].

Variable fields

$1: AC IP address.

$2: Reason:

·     Added AP IP address.

·     Deleted AP IP address.

·     AP interface used for CAPWAP tunnel went down.

·     AP config changed.

·     AP was reset.

·     Number of echo retransmission attempts exceeded the limit.

·     Full retransmission queue.

·     Data channel timer expired.

·     Backup AC IP address changed.

·     Backup tunnel changed to master tunnel.

·     Failed to change backup tunnel to master tunnel.

·     Backup method changed.

·     N/A.

Severity level

6

Example

APMGR/6/APMGR_CWC_TUNNEL_DOWN: CAPWAP tunnel to AC 192.168.10.1 went down. Reason: AP was reset.

Explanation

The CAPWAP tunnel between the AP and the AC was terminated for a specific reason.

Recommended action

Examine the network connection between the AP and the AC.

 

APMGR_CWC_TUNNEL_UP

Message text

[STRING] CAPWAP tunnel to AC [STRING] went up.

Variable fields

$1: Tunnel type:

·     Master.

·     Backup.

$2: AC IP address.

Severity level

6

Example

APMGR/6/APMGR_CWC_TUNNEL_UP: Master CAPWAP tunnel to AC 192.168.10.1 went up.

Explanation

The AP was connected to the AC successfully and entered Run state.

Recommended action

No action is required.

 

APMGR_CWS_IMG_DOWNLOAD_COMPLETE

Message text

System software image file [STRING] downloading through the CAPWAP tunnel for AP [STRING] completed.

Variable fields

$1: Image file name.

$2: AP name.

Severity level

6

Example

APMGR/6/APMGR_ CWS_IMG_DOWNLOAD_COMPLETE: System software image file 5800.ipe downloading through the CAPWAP tunnel for AP ap2 completed.

Explanation

The AP downloaded the image file from the AC successfully.

Recommended action

No action is required.

 

APMGR_CWS_IMG_DOWNLOAD_START

Message text

AP [STRING] started to download the system software image file [STRING].

Variable fields

$1: AP name.

$2: Image file name.

Severity level

6

Example

APMGR/6/APMGR_CWS_IMG_DOWNLOAD_START: AP ap1 started to download the system software image file 5800.ipe.

Explanation

The AP started to download the image file from the AC.

Recommended action

No action is required.

 

APMGR_CWS_LOCAL_AC_DOWN

Message text

CAPWAP tunnel to local AC [STRING] went down. Reason: [STRING].

Variable fields

$1: IP address of the local AC.

$2: Reason:

·     Neighbor dead timer expired.

·     Local AC was deleted.

·     Serial number changed.

·     Processed join request in Run state.

·     Failed to retransmit message.

·     N/A

Severity level

4

Example

APMGR/4/APMGR_CWS_LOCAL_AC_DOWN: CAPWAP tunnel to local AC 1.1.1.1 went down. Reason: Serial number changed.

Explanation

The CAPWAP tunnel between the central AC and the local AC was terminated for a specific reason.

Recommended action

To resolve the issue:

1.     Examine the network connection between the central AC and the local AC.

2.     Verify that the central AC is correctly configured.

3.     Verify that the local AC is correctly configured.

4.     If the issue persists, contact H3C Support.

 

APMGR_CWS_LOCAL_AC_UP

Message text

CAPWAP tunnel to local AC [STRING] went up.

Variable fields

$1: IP address of the local AC.

Severity level

6

Example

APMGR/6/APMGR_CWS_LOCAL_AC_UP: CAPWAP tunnel to local AC 1.1.1.1 went up.

Explanation

The central AC has established a CAPWAP tunnel with the local AC.

Recommended action

No action is required.

 

APMGR_CWS_RUN_DOWNLOAD_COMPLETE

Message text

File [STRING] successfully downloaded through the CAPWAP tunnel for AP [STRING].

Variable fields

$1: File name.

$2: AP name.

Severity level

6

Example

APMGR/6/APMGR_CWS_RUN_DOWNLOAD_COMPLETE: File ac.cfg successfully downloaded through the CAPWAP tunnel for AP ap2.

Explanation

The AP downloaded the file from the AC successfully.

Recommended action

No action is required.

 

APMGR_CWS_RUN_DOWNLOAD_START

Message text

AP [STRING] started to download the file [STRING].

Variable fields

$1: AP name.

$2: File name.

Severity level

6

Example

APMGR/6/APMGR_CWS_RUN_DOWNLOAD_START: AP ap1 started to download the file ac.cfg.

Explanation

The AP started to download the file from the AC.

Recommended action

No action is required.

 

APMGR_CWS_TUNNEL_DOWN

Message text

CAPWAP tunnel to AP [STRING] went down. Reason: [STRING].

Variable fields

$1: AP name.

$2: Reason:

·     Neighbor dead timer expired.

·     AP was reset.

·     AP was deleted.

·     Serial number changed.

·     Processed join request in Run state.

·     Failed to retransmit message.

·     Received WTP tunnel down event from AP.

·     Backup AC closed the backup tunnel.

·     Tunnel switched.

·     N/A.

Severity level

6

Example

APMGR/6/APMGR_CWS_TUNNEL_DOWN: CAPWAP tunnel to AP ap1 went down. Reason: AP was reset.

Explanation

The AP went offline for a specific reason.

Recommended action

To resolve the issue:

1.     Examine the network connection between the AP and the AC.

2.     Verify that the AP is correctly configured.

3.     Verify that the AC is correctly configured.

4.     If the issue persists, contact H3C Support.

 

APMGR_CWS_TUNNEL_UP

Message text

[STRING] CAPWAP tunnel to AP [STRING] went up.

Variable fields

$1: Tunnel type:

·     Master.

·     Backup.

$2: AP name.

Severity level

6

Example

APMGR/6/APMGR_CWS_TUNNEL_UP: Backup CAPWAP tunnel to AP ap1 went up.

Explanation

The AP came online and entered Run state.

Recommended action

No action is required.

 

APMGR_DELBAC_INFO

Message text

Delete BAS AC [STRING].

Variable fields

$1: MAC address of the BAS AC.

Severity level

6

Example

APMGR/6/APMGR_DELBAC_INFO: Delete BAS AC 3ce5-a616-28cd.

Explanation

The BAS AC was disconnected from the master AC.

Recommended action

No action is required.

 

APMGR_LOCAL_AC_OFFLINE

Message text

Local AC [STRING] went offline. State changed to Idle.

Variable fields

$1: Name of the local AC.

Severity level

6

Example

APMGR/6/APMGR_LOCAL_AC_OFFLINE: Local AC ac1 went offline. State changed to Idle.

Explanation

The local AC went offline. The state of the local AC changed to Idle.

Recommended action

1.     If the local AC went offline abnormally, check the debugging information to locate the issue and resolve it.

2.     If the issue persists, contact H3C Support.

 

APMGR_LOCAL_AC_ONLINE

Message text

Local AC [STRING] went online. State changed to Run.

Variable fields

$1: Name of the local AC.

Severity level

6

Example

APMGR/6/APMGR_LOCAL_AC_ONLINE: Local AC ac1 went online. State changed to Run.

Explanation

The local AC came online. The state of the local AC changed to Run.

Recommended action

No action is required.

 

 

 


ARP messages

This section contains ARP messages.

ARP_ACTIVE_ACK_NO_REPLY

Message text

No ARP reply from IP [STRING] was received on interface [STRING].

Variable fields

$1: IP address.

$2: Interface name.

Severity level

6

Example

ARP/6/ARP_ACTIVE_ACK_NO_REPLY: No ARP reply from IP 192.168.10.1 was received on interface GigabitEthernet1/0/1.

Explanation

The ARP active acknowledgement feature did not receive an ARP reply after it sent an ARP request to the sender IP of an ARP message.

This message indicates the risk of attacks.

Recommended action

1.     Verify that the learned ARP entries on the device are consistent with the existing legal devices. When gateways and servers are on the network, check the ARP entries for these devices first.

2.     If the ARP entries are correct and the attack continues, contact H3C Support.

 

ARP_ACTIVE_ACK_NOREQUESTED_REPLY

Message text

Interface [STRING] received from IP [STRING] an ARP reply that was not requested by the device.

Variable fields

$1: Interface name.

$2: IP address.

Severity level

6

Example

ARP/6/ARP_ACTIVE_ACK_NOREQUESTED_REPLY: Interface GigabitEthernet1/0/1 received from IP 192.168.10.1 an ARP reply that was not requested by the device.

Explanation

The ARP active acknowledgement feature received an unsolicited ARP reply from a sender IP.

This message indicates the risk of attacks.

Recommended action

No action is required. The device discards the ARP reply automatically.

 

ARP_BINDRULETOHW_FAILED

Message text

Failed to download binding rule to hardware on the interface [STRING], SrcIP [IPADDR], SrcMAC [MAC], VLAN [UINT16], Gateway MAC [MAC].

Variable fields

$1: Interface name.

$2: Source IP address.

$3: Source MAC address.

$4: VLAN ID.

$5: Gateway MAC address.

Severity level

5

Example

ARP/5/ARP_BINDRULETOHW_FAILED: Failed to download binding rule to hardware on the interface GigabitEthernet1/0/1, SrcIP 1.1.1.132, SrcMAC 0015-E944-A947, VLAN 1, Gateway MAC 00A1-B812-1108.

Explanation

The system failed to set a binding rule to the hardware on an interface. The message is sent in any of the following situations:

·     The resources are not sufficient for the operation.

·     The memory is not sufficient for the operation.

·     A hardware error occurs.

Recommended action

To resolve the problem:

1.     Execute the display qos-acl resource command to check if the ACL resources for the operation are sufficient.

¡     If yes, proceed to step 2.

¡     If no, delete unnecessary configuration to release ACL resources. If no configuration can be deleted, proceed to step 2.

2.     Execute the display memory command to check if the memory for the operation is sufficient.

¡     If yes, proceed to step 3.

¡     If no, delete unnecessary configuration to release memory. If no configuration can be deleted, proceed to step 3.

3.     Delete the configuration and perform the operation again.

 

ARP_DETECTION_LOG

Message text

Detected an ARP attack on interface [STRING]: IP [STRING], MAC [STRING], VLAN [STRING]. [UINT32] packet(s) dropped.

Variable fields

$1: Interface name.

$2: IP address.

$3: MAC address.

$4: VLAN ID.

$5: Number of dropped packets.

Severity level

5

Example

ARP/5/ARP_INSPECTION: -MDC=1; Detected an ARP attack on interface GigabitEthernet1/0/1: IP 1.1.1.1, MAC 1-1-1, VLAN 100. 2 packet(s) dropped.

Explanation

An ARP attack was detected on an interface and attack packets were dropped.

Recommended action

Check the source of the ARP attack.

 

ARP_DUPLICATE_IPADDR_DETECT

Message text

Detected an IP address conflict. The device with MAC address [STRING] connected to interface [STRING] in VSI [STRING] and the device with MAC address [STRING] connected to interface [STRING] in VSI [STRING] were using the same IP address [IPADDR].

Variable fields

$1: MAC address.

$2: Interface name. (The interface can be a tunnel interface, Layer 3 interface, or Ethernet service instance.)

$3: VSI name.

$4: MAC address.

$5: Interface name. (The interface can be a tunnel interface, Layer 3 interface, or Ethernet service instance.)

$6: VSI name.

$7: Conflicting IP address.

Severity level

4

Example

ARP/4/ARP_DUPLICATE_IPADDR_DETECT: Detected an IP address conflict. The device with MAC address 00-00-01 connected to interface GigabitEthernet1/0/1 service-instance 1000 in VSI vpna and the device with MAC address 00-00-02 connected to interface tunnel 10 in VSI vpna were using the same IP address 192.168.1.1.

Explanation

This message is sent when an interface receives an ARP message in which the sender information conflicts with an existing ARP entry. The sender IP address is the same as the IP address in the entry, but the MAC addresses are different.

Recommended action

Change the IP address on either of the two devices.

 

ARP_DYNAMIC

Message text

The maximum number of dynamic ARP entries for the device reached.

Variable fields

N/A

Severity level

6

Example

ARP/6/ARP_DYNAMIC: The maximum number of dynamic ARP entries for the device reached.

Explanation

The maximum number of dynamic ARP entries for the device was reached.

Recommended action

No action is required.

 

ARP_DYNAMIC_IF

Message text

The maximum number of dynamic ARP entries for interface [STRING] reached.

Variable fields

$1: Interface name.

Severity level

6

Example

ARP/6/ARP_DYNAMIC_IF: The maximum number of dynamic ARP entries for interface GigabitEthernet1/0/1 reached.

Explanation

The maximum number of dynamic ARP entries for the specified interface was reached.

Recommended action

No action is required.

 

ARP_DYNAMIC_SLOT

Message text

Pattern 1:

The maximum number of dynamic ARP entries for slot [INT32] reached.

Pattern 2:

The maximum number of dynamic ARP entries for chassis [INT32] slot [INT32] reached.

Variable fields

Pattern 1:

$1: Slot number.

Pattern 2:

$1: Chassis number.

$2: Slot number.

Severity level

6

Example

ARP/6/ARP_DYNAMIC_SLOT: The maximum number of dynamic ARP entries for slot 2 reached.

Explanation

Pattern 1:

The maximum number of dynamic ARP entries for the slot was reached.

Pattern 2:

The maximum number of dynamic ARP entries for the slot on the chassis was reached.

Recommended action

No action is required.

 

ARP_ENTRY_CONFLICT

Message text

The software entry for [STRING] on [STRING] and the hardware entry did not have the same [STRING].

Variable fields

$1: IP address.

$2: VPN instance name. If the ARP entry belongs to the public network, this field displays the public network.

$3: Inconsistent items:

¡     MAC address.

¡     output interface.

¡     output port.

¡     outermost layer VLAN ID.

¡     second outermost layer VLAN ID.

¡     VSI index.

¡     link ID.

Severity level

6

Example

ARP/6/ARP_ENTRY_CONFLICT: The software entry for 1.1.1.1 on the VPN a and the hardware entry did not have the same MAC address, output port, VSI index, and link ID.

ARP/6/ARP_ENTRY_CONFLICT: The software entry for 1.1.1.2 on the public network and the hardware entry did not have the same MAC address, output port, VSI index, and link ID.

Explanation

The software entry for the specified IP address is not the same as the hardware entry. For example, they do not have the same output interface.

Recommended action

No action is required. ARP automatically refreshes the hardware entries.

 

ARP_HOST_IP_CONFLICT

Message text

The host [STRING] connected to interface [STRING] cannot communicate correctly, because it uses the same IP address as the host connected to interface [STRING].

Variable fields

$1: IP address.

$2: Interface name.

$3: Interface name.

Severity level

4

Example

ARP/4/ARP_HOST_IP_CONFLICT: The host 1.1.1.1 connected to interface GigabitEthernet1/0/1 cannot communicate correctly, because it uses the same IP address as the host connected to interface GigabitEthernet1/0/2.

Explanation

The sender IP address in a received ARP message conflicted with the IP address of a host connected to another interface.

Recommended action

Check whether the hosts that send the ARP messages are legitimate. Disconnect the illegal host from the network.

 

ARP_LOCALPROXY_ENABLE_FAILED

Message text

Failed to enable local proxy ARP on interface [STRING].

Variable fields

$1: Interface name.

Severity level

4

Example

ARP/4/ARP_LOCALPROXY_ENABLE_FAILED: -MDC=1-Slot=2; Failed to enable local proxy ARP on interface VSI-interface 1.

Explanation

This message is sent when the device fails to enable local proxy ARP on an interface in a slot. If the interface resides on the MPU, the slot number is 0.

Recommended action

1.     Verify that the card supports local proxy ARP.

2.     Verify that sufficient hardware resources are available.

 

ARP_RATE_EXCEEDED

Message text

The ARP packet rate ([UINT32] pps) exceeded the rate limit ([UINT32] pps) on interface [STRING] in the last [UINT32] seconds.

Variable fields

$1: ARP packet rate.

$2: ARP limit rate.

$3: Interface name.

$4: Interval time.

Severity level

4

Example

ARP/4/ARP_RATE_EXCEEDED: The ARP packet rate (100 pps) exceeded the rate limit (80 pps) on interface GigabitEthernet1/0/1 in the last 10 seconds.

Explanation

An interface received ARP messages at a higher rate than the rate limit.

Recommended action

Verify that the hosts at the sender IP addresses are legitimate.

 

ARP_RATELIMIT_NOTSUPPORT

Message text

Pattern 1:

ARP packet rate limit is not support on slot [INT32].

Pattern 2:

ARP packet rate limit is not support on chassis [INT32] slot [INT32].

Variable fields

Pattern 1:

$1: Slot number.

Pattern 2:

$1: Chassis number.

$2: Slot number.

Severity level

6

Example

ARP/6/ARP_RATELIMIT_NOTSUPPORT: ARP packet rate limit is not support on slot 2.

Explanation

Pattern 1:

ARP packet rate limit is not supported on the slot.

Pattern 2:

ARP packet rate limit is not supported on the slot of the chassis was reached.

Recommended action

Verify that the host at the sender IP address is legitimate.

 

ARP_SENDER_IP_INVALID

Message text

Sender IP [STRING] was not on the same network as the receiving interface [STRING].

Variable fields

$1: IP address.

$2: Interface name.

Severity level

6

Example

ARP/6/ARP_SENDER_IP_INVALID: Sender IP 192.168.10.2 was not on the same network as the receiving interface GigabitEthernet1/0/1.

Explanation

The sender IP of a received ARP message was not on the same network as the receiving interface.

Recommended action

Verify that the host at the sender IP address is legitimate.

 

ARP_SENDER_MAC_INVALID

Message text

Sender MAC [STRING] was not identical to Ethernet source MAC [STRING] on interface [STRING].

Variable fields

$1: MAC address.

$2: MAC address.

$3: Interface name.

Severity level

6

Example

ARP/6/ARP_SENDER_MAC_INVALID: Sender MAC 0000-5E14-0E00 was not identical to Ethernet source MAC 0000-5C14-0E00 on interface GigabitEthernet1/0/1.

Explanation

An interface received an ARP message. The sender MAC address in the message body was not identical to the source MAC address in the Ethernet header.

Recommended action

Verify that the host at the sender MAC address is legitimate.

 

ARP_SENDER_SMACCONFLICT

Message text

Packet was discarded because its sender MAC address was the MAC address of the receiving interface.

Interface: [STRING], sender IP: [STRING], target IP: [STRING].

Variable fields

$1: Interface name.

$2: Sender IP address.

$3: Target IP address.

Severity level

6

Example

ARP/6/ ARP_SENDER_SMACCONFLICT: Packet discarded for the sender MAC address is the same as the receiving interface.

Interface: GigabitEthernet1/0/1 sender IP: 1.1.2.2 target IP: 1.1.2.1,

Explanation

The sender MAC address of a received ARP packet conflicts with the MAC address of the device.

Recommended action

No action is required.

 

ARP_SENDER_SMACCONFLICT_VSI

Message text

Packet was discarded because its sender MAC address was the MAC address of the receiving interface.

Interface: [STRING], sender IP: [STRING], target IP: [STRING],VSI index: [UINT32], link ID: [UINT32].

Variable fields

$1: Interface name.

$2: Sender IP address.

$3: Target IP address.

$4: VSI index.

$5: Link ID.

Severity level

6

Example

ARP/6/ ARP_SENDER_SMACCONFLICT_VSI: Packet discarded for the sender MAC address is the same as the receiving interface.

Interface: VSI3 sender IP: 1.1.2.2 target IP: 1.1.2.1, VSI Index: 2, Link ID: 0

Explanation

The sender MAC address of a received ARP packet conflicts with the MAC address of the device. The receiving interface is a VSI interface.

Recommended action

No action is required.

 

ARP_SRC_MAC_FOUND_ATTACK

Message text

An attack from MAC [STRING] was detected on interface [STRING].

Variable fields

$1: MAC address.

$2: Interface name.

Severity level

6

Example

ARP/6/ARP_SRC_MAC_FOUND_ATTACK: An attack from MAC 0000-5E14-0E00 was detected on interface GigabitEthernet1/0/1.

Explanation

The source MAC-based ARP attack detection feature received more ARP packets from the same MAC address within 5 seconds than the specified threshold.

This message indicates the risk of attacks.

Recommended action

Verify that the host at the source MAC address is legitimate.

 

ARP_SUP_ENABLE_FAILED

Message text

Failed to enable ARP flood suppression on VSI [STRING].

Variable fields

$1: VSI name.

Severity level

4

Example

ARP/4/ARP_SUP_ENABLE_FAILED: -MDC=1; Failed to enable ARP flood suppression on VSI vpna.

Explanation

This message is sent when the system failed to enable ARP flood suppression for a VSI. The minimum interval between two log messages is 2 seconds. To make the system send the message successfully, wait for a minimum of 2 seconds before you enable ARP flood suppression for another VSI.

Recommended action

1.     Verify that the device supports ARP flood suppression.

2.     Verify that the hardware resources are sufficient.

 

ARP_TARGET_IP_INVALID

Message text

Target IP [STRING] was not the IP of the receiving interface [STRING].

Variable fields

$1: IP address.

$2: Interface name.

Severity level

6

Example

ARP/6/ARP_TARGET_IP_INVALID: Target IP 192.168.10.2 was not the IP of the receiving interface GigabitEthernet1/0/1.

Explanation

The target IP address of a received ARP message was not the IP address of the receiving interface.

Recommended action

Verify that the host at the sender IP address is legitimate.

 

ARP_THRESHOLD_REACHED

Message text

The alarm threshold for dynamic ARP entry learning was reached on interface [STRING].

Variable fields

$1: Interface name.

Severity level

4

Example

ARP/4/ARP_THRESHOLD_REACHED: The alarm threshold for dynamic ARP entry learning was reached on interface GigabitEthernet1/0/1.

Explanation

This message is sent when the alarm threshold for dynamic ARP learning was reached on GigabitEthernet 1/0/1.

Recommended action

Verify that the number of learned dynamic ARP entries matches the actual number of devices in the network and no ARP attack sources exist in the network.

 

ARP_USER_DUPLICATE_IPADDR_DETECT

Message text

Detected a user IP address conflict. New user (MAC [STRING], SVLAN [STRING], CVLAN [STRING]) on interface [STRING] and old user (MAC [STRING], SVLAN [STRING], CVLAN [STRING]) on interface [STRING] were using the same IP address [IPADDR].

Variable fields

$1: MAC address of a new user.

$2: Outer VLAN to which the new user belongs.

$3: Inner VLAN to which the new user belongs.

$4: Name of the interface connecting to the new user.

$5: MAC address of an old user.

$6: Outer VLAN to which the old user belongs.

$7: Inner VLAN to which the old user belongs.

$8: Name of the interface connecting to the old user.

$9: IP address.

Severity level

6

Example

ARP/6/ARP_USER_DUPLICATE_IPADDR_DETECT: Detected a user IP address conflict. New user (MAC 0010-2100-01e1, SVLAN 100, CVLAN 10) on interface GigabitEthernet1/0/1 and old user (MAC 0120-1e00-0102, SVLAN 100, CVLAN 10) on interface GigabitEthernet1/0/1 were using the same IP address 192.168.1.1.

Explanation

ARP detected a user IP address conflict. The IP address of a new user is the same as the IP address of an old user.

Recommended action

Verify that all users have different IP addresses.

 

ARP_USER_MOVE_DETECT

Message text

Detected a user (IP address [IPADDR], MAC address [STRING]) moved to another interface. Before user move: interface [STRING], SVLAN [STRING], CVLAN [STRING]. After user move: interface [STRING], SVLAN [STRING], CVLAN [STRING].

Variable fields

$1: IP address of the user.

$2: MAC address of the user.

$3: Interface name before the migration.

$4: Outer VLAN to which the user belongs before the migration.

$5: Inner VLAN to which the user belongs before the migration.

$6: Interface name after the migration.

$7: Outer VLAN to which the user belongs after the migration.

$8: Inner VLAN to which the user belongs after the migration.

Severity level

6

Example

ARP/6/ARP_USER_MOVE_DETECT: Detected a user (IP address 192.168.1.1, MAC address 0010-2100-01e1) moved to another interface. Before user move: interface GigabitEthernet1/0/1, SVLAN 100, CVLAN 10. After user move: interface GigabitEthernet1/0/2, SVLAN 100, CVLAN 10.

Explanation

ARP detected a user accesses the network through another port.

Recommended action

Use the display arp user-move record command to verify that the migration is legitimate.

 

DUPIFIP

Message text

Duplicate address [STRING] on interface [STRING], sourced from [STRING].

Variable fields

$1: IP address.

$2: Interface name.

$3: MAC Address.

Severity level

6

Example

ARP/6/DUPIFIP: Duplicate address 1.1.1.1 on interface GigabitEthernet1/0/1, sourced from 0015-E944-A947.

Explanation

ARP detected a duplicate address.

The sender IP in the received ARP packet was being used by the receiving interface.

Recommended action

Modify the IP address configuration.

 

DUPIP

Message text

IP address [STRING] conflicted with global or imported IP address, sourced from [STRING].

Variable fields

$1: IP address.

$2: MAC Address.

Severity level

6

Example

ARP/6/DUPIP: IP address 30.1.1.1 conflicted with global or imported IP address, sourced from 0000-0000-0001.

Explanation

The sender IP address of the received ARP packet conflicted with the global or imported IP address.

Recommended action

Modify the IP address configuration.

 

DUPVRRPIP

Message text

IP address [STRING] conflicted with VRRP virtual IP address on interface [STRING], sourced from [STRING].

Variable fields

$1: IP address.

$2: Interface name.

$3: MAC address.

Severity level

6

Example

ARP/6/DUPVRRPIP: IP address 1.1.1.1 conflicted with VRRP virtual IP address on interface GigabitEthernet1/0/1, sourced from 0015-E944-A947.

Explanation

The sender IP address of the received ARP packet conflicted with the VRRP virtual IP address.

Recommended action

Modify the IP address configuration.

 

 


ATK messages

This section contains attack detection and prevention messages.

ATK_ICMP_ADDRMASK_REQ

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_REQ: IcmpType(1058)=17; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP address mask request logs are aggregated.

Recommended action