H3C Fixed-Port Switches System Log Messages Reference-R63xx-6W101

HomeSupportResource CenterDiagnose & MaintainH3C Fixed-Port Switches System Log Messages Reference-R63xx-6W101

 

H3C Fixed-Port Switches

System Log Messages Reference – R63xx

 

 

This manual is applicable to the following switches and software versions:

 

S6520X-HI[EI][SI] & S5560X-HI Switch Series (Release 6308 and later)

S5560X-EI Switch Series (Release 6308 and later)

S5130S-EI[HI] Switch Series (Release 6308 and later)

S5120V2-LI Switch Series (Release 6308P01 and later)

S5560S-EI & S3100V3-EI Switch Series  (Release 6309P01 and later)

S5560S-SI & S5500V3-SI Switch Series (Release 6310 and later)

S5130S-LI &  S5000V3-EI Switch Series (Release 6310 and later)

IE4300-12P-AC & IE4300-12P-PWR (Release 6318P01 and later)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Document version: 6W101-20220415

 

Copyright © 2022 New H3C Technologies Co., Ltd. All rights reserved.

No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of New H3C Technologies Co., Ltd.

Except for the trademarks of New H3C Technologies Co., Ltd., any trademarks that may be mentioned in this document are the property of their respective owners.

The information in this document is subject to change without notice.


Contents

Introduction· 1

System log message format 1

Managing and obtaining system log messages· 3

Obtaining log messages from the console terminal 3

Obtaining log messages from a monitor terminal 3

Obtaining log messages from the log buffer 4

Obtaining log messages from the log file· 4

Obtaining log messages from a log host 4

Software module list 4

Using this document 8

AAA messages· 10

AAA_FAILURE· 10

AAA_LAUNCH· 10

AAA_SUCCESS· 11

ACL messages· 12

ACL_ACCELERATE_NO_RES· 12

ACL_ACCELERATE_NONCONTIGUOUSMASK· 12

ACL_ACCELERATE_NOT_SUPPORT· 12

ACL_ACCELERATE_NOT_SUPPORTHOPBYHOP· 13

ACL_ACCELERATE_NOT_SUPPORTMULTITCPFLAG·· 13

ACL_ACCELERATE_UNK_ERR· 13

ACL_IPV6_STATIS_INFO·· 14

ACL_NO_MEM·· 14

ACL_STATIS_INFO·· 14

ANCP messages· 15

ANCP_INVALID_PACKET· 15

APMGR messages· 16

APMGR_AC_MEM_ALERT· 16

APMGR_ADD_AP_FAIL· 16

APMGR_ADDBAC_INFO·· 17

APMGR_AP_OFFLINE· 17

APMGR_AP_ONLINE· 17

APMGR_CWC_IMG_DOWNLOAD_COMPLETE· 18

APMGR_CWC_IMG_DOWNLOAD_START· 18

APMGR_CWC_IMG_NO_ENOUGH_SPACE· 18

APMGR_CWC_LOCAL_AC_DOWN· 19

APMGR_CWC_LOCAL_AC_UP· 19

APMGR_CWC_REBOOT· 20

APMGR_CWC_RUN_DOWNLOAD_COMPLETE· 20

APMGR_CWC_RUN_DOWNLOAD_START· 20

APMGR_CWC_RUN_NO_ENOUGH_SPACE· 21

APMGR_CWC_TUNNEL_DOWN· 21

APMGR_CWC_TUNNEL_UP· 22

APMGR_CWS_IMG_DOWNLOAD_COMPLETE· 22

APMGR_CWS_IMG_DOWNLOAD_START· 22

APMGR_CWS_LOCAL_AC_DOWN· 23

APMGR_CWS_LOCAL_AC_UP· 23

APMGR_CWS_RUN_DOWNLOAD_COMPLETE· 24

APMGR_CWS_RUN_DOWNLOAD_START· 24

APMGR_CWS_TUNNEL_DOWN· 25

APMGR_CWS_TUNNEL_UP· 25

APMGR_DELBAC_INFO·· 26

APMGR_LOCAL_AC_OFFLINE· 26

APMGR_LOCAL_AC_ONLINE· 26

ARP messages· 27

ARP_ACTIVE_ACK_NO_REPLY· 27

ARP_ACTIVE_ACK_NOREQUESTED_REPLY· 27

ARP_BINDRULETOHW_FAILED·· 28

ARP_DETECTION_LOG·· 28

ARP_DUPLICATE_IPADDR_DETECT· 29

ARP_DYNAMIC· 29

ARP_DYNAMIC_IF· 30

ARP_DYNAMIC_SLOT· 30

ARP_ENTRY_CONFLICT· 31

ARP_HOST_IP_CONFLICT· 31

ARP_LOCALPROXY_ENABLE_FAILED·· 32

ARP_RATE_EXCEEDED·· 32

ARP_RATELIMIT_NOTSUPPORT· 33

ARP_SENDER_IP_INVALID·· 33

ARP_SENDER_MAC_INVALID·· 34

ARP_SENDER_SMACCONFLICT· 34

ARP_SENDER_SMACCONFLICT_VSI 35

ARP_SRC_MAC_FOUND_ATTACK· 35

ARP_SUP_ENABLE_FAILED·· 36

ARP_TARGET_IP_INVALID·· 36

ARP_THRESHOLD_REACHED·· 36

ARP_USER_DUPLICATE_IPADDR_DETECT· 37

ARP_USER_MOVE_DETECT· 38

DUPIFIP· 38

DUPIP· 39

DUPVRRPIP· 39

ATK messages· 40

ATK_ICMP_ADDRMASK_REQ·· 40

ATK_ICMP_ADDRMASK_REQ_RAW·· 41

ATK_ICMP_ADDRMASK_REQ_RAW_SZ· 42

ATK_ICMP_ADDRMASK_REQ_SZ· 43

ATK_ICMP_ADDRMASK_RPL· 44

ATK_ICMP_ADDRMASK_RPL_RAW·· 45

ATK_ICMP_ADDRMASK_RPL_RAW_SZ· 46

ATK_ICMP_ADDRMASK_RPL_SZ· 47

ATK_ICMP_ECHO_REQ·· 48

ATK_ICMP_ECHO_REQ_RAW·· 49

ATK_ICMP_ECHO_REQ_RAW_SZ· 50

ATK_ICMP_ECHO_REQ_SZ· 51

ATK_ICMP_ECHO_RPL· 52

ATK_ICMP_ECHO_RPL_RAW·· 53

ATK_ICMP_ECHO_RPL_RAW_SZ· 54

ATK_ICMP_ECHO_RPL_SZ· 55

ATK_ICMP_FLOOD·· 56

ATK_ICMP_FLOOD_SZ· 56

ATK_ICMP_INFO_REQ·· 57

ATK_ICMP_INFO_REQ_RAW·· 58

ATK_ICMP_INFO_REQ_RAW_SZ· 59

ATK_ICMP_INFO_REQ_SZ· 60

ATK_ICMP_INFO_RPL· 61

ATK_ICMP_INFO_RPL_RAW·· 62

ATK_ICMP_INFO_RPL_RAW_SZ· 63

ATK_ICMP_INFO_RPL_SZ· 64

ATK_ICMP_LARGE· 65

ATK_ICMP_LARGE_RAW·· 66

ATK_ICMP_LARGE_RAW_SZ· 66

ATK_ICMP_LARGE_SZ· 67

ATK_ICMP_PARAPROBLEM·· 68

ATK_ICMP_PARAPROBLEM_RAW·· 69

ATK_ICMP_PARAPROBLEM_RAW_SZ· 70

ATK_ICMP_PARAPROBLEM_SZ· 71

ATK_ICMP_PINGOFDEATH· 72

ATK_ICMP_PINGOFDEATH_RAW·· 73

ATK_ICMP_PINGOFDEATH_RAW_SZ· 73

ATK_ICMP_PINGOFDEATH_SZ· 74

ATK_ICMP_REDIRECT· 75

ATK_ICMP_REDIRECT_RAW·· 76

ATK_ICMP_REDIRECT_RAW_SZ· 77

ATK_ICMP_REDIRECT_SZ· 78

ATK_ICMP_SMURF· 79

ATK_ICMP_SMURF_RAW·· 80

ATK_ICMP_SMURF_RAW_SZ· 81

ATK_ICMP_SMURF_SZ· 82

ATK_ICMP_SOURCEQUENCH· 83

ATK_ICMP_SOURCEQUENCH_RAW·· 84

ATK_ICMP_SOURCEQUENCH_RAW_SZ· 85

ATK_ICMP_SOURCEQUENCH_SZ· 86

ATK_ICMP_TIMEEXCEED·· 87

ATK_ICMP_TIMEEXCEED_RAW·· 88

ATK_ICMP_TIMEEXCEED_RAW_SZ· 89

ATK_ICMP_TIMEEXCEED_SZ· 90

ATK_ICMP_TRACEROUTE· 91

ATK_ICMP_TRACEROUTE_RAW·· 92

ATK_ICMP_TRACEROUTE_RAW_SZ· 92

ATK_ICMP_TRACEROUTE_SZ· 93

ATK_ICMP_TSTAMP_REQ·· 94

ATK_ICMP_TSTAMP_REQ_RAW·· 95

ATK_ICMP_TSTAMP_REQ_RAW_SZ· 96

ATK_ICMP_TSTAMP_REQ_SZ· 97

ATK_ICMP_TSTAMP_RPL· 98

ATK_ICMP_TSTAMP_RPL_RAW·· 99

ATK_ICMP_TSTAMP_RPL_RAW_SZ· 100

ATK_ICMP_TSTAMP_RPL_SZ· 101

ATK_ICMP_TYPE· 102

ATK_ICMP_TYPE_RAW·· 103

ATK_ICMP_TYPE_RAW_SZ· 104

ATK_ICMP_TYPE_SZ· 105

ATK_ICMP_UNREACHABLE· 106

ATK_ICMP_UNREACHABLE_RAW·· 107

ATK_ICMP_UNREACHABLE_RAW_SZ· 108

ATK_ICMP_UNREACHABLE_SZ· 109

ATK_ICMPV6_DEST_UNREACH· 110

ATK_ICMPV6_DEST_UNREACH_RAW·· 111

ATK_ICMPV6_DEST_UNREACH_RAW_SZ· 111

ATK_ICMPV6_DEST_UNREACH_SZ· 112

ATK_ICMPV6_ECHO_REQ·· 113

ATK_ICMPV6_ECHO_REQ_RAW·· 114

ATK_ICMPV6_ECHO_REQ_RAW_SZ· 114

ATK_ICMPV6_ECHO_REQ_SZ· 115

ATK_ICMPV6_ECHO_RPL· 116

ATK_ICMPV6_ECHO_RPL_RAW·· 117

ATK_ICMPV6_ECHO_RPL_RAW_SZ· 117

ATK_ICMPV6_ECHO_RPL_SZ· 118

ATK_ICMPV6_FLOOD·· 119

ATK_ICMPV6_FLOOD_SZ· 119

ATK_ICMPV6_GROUPQUERY· 120

ATK_ICMPV6_GROUPQUERY_RAW·· 121

ATK_ICMPV6_GROUPQUERY_RAW_SZ· 121

ATK_ICMPV6_GROUPQUERY_SZ· 122

ATK_ICMPV6_GROUPREDUCTION· 123

ATK_ICMPV6_GROUPREDUCTION_RAW·· 124

ATK_ICMPV6_GROUPREDUCTION_RAW_SZ· 124

ATK_ICMPV6_GROUPREDUCTION_SZ· 125

ATK_ICMPV6_GROUPREPORT· 126

ATK_ICMPV6_GROUPREPORT_RAW·· 127

ATK_ICMPV6_GROUPREPORT_RAW_SZ· 127

ATK_ICMPV6_GROUPREPORT_SZ· 128

ATK_ICMPV6_LARGE· 129

ATK_ICMPV6_LARGE_RAW·· 129

ATK_ICMPV6_LARGE_RAW_SZ· 130

ATK_ICMPV6_LARGE_SZ· 130

ATK_ICMPV6_PACKETTOOBIG·· 131

ATK_ICMPV6_PACKETTOOBIG_RAW·· 132

ATK_ICMPV6_PACKETTOOBIG_RAW_SZ· 132

ATK_ICMPV6_PACKETTOOBIG_SZ· 133

ATK_ICMPV6_PARAPROBLEM·· 134

ATK_ICMPV6_PARAPROBLEM_RAW·· 135

ATK_ICMPV6_PARAPROBLEM_RAW_SZ· 135

ATK_ICMPV6_PARAPROBLEM_SZ· 136

ATK_ICMPV6_TIMEEXCEED·· 137

ATK_ICMPV6_TIMEEXCEED_RAW·· 138

ATK_ICMPV6_TIMEEXCEED_RAW_SZ· 138

ATK_ICMPV6_TIMEEXCEED_SZ· 139

ATK_ICMPV6_TRACEROUTE· 140

ATK_ICMPV6_TRACEROUTE_RAW·· 141

ATK_ICMPV6_TRACEROUTE_RAW_SZ· 142

ATK_ICMPV6_TRACEROUTE_SZ· 143

ATK_ICMPV6_TYPE· 144

ATK_ICMPV6_TYPE _RAW_SZ· 145

ATK_ICMPV6_TYPE_RAW·· 145

ATK_ICMPV6_TYPE_SZ· 146

ATK_IP_OPTION· 147

ATK_IP_OPTION_RAW·· 148

ATK_IP_OPTION_RAW_SZ· 149

ATK_IP_OPTION_SZ· 150

ATK_IP4_ACK_FLOOD·· 151

ATK_IP4_ACK_FLOOD_SZ· 151

ATK_IP4_DIS_PORTSCAN· 152

ATK_IP4_DIS_PORTSCAN_SZ· 152

ATK_IP4_DNS_FLOOD·· 153

ATK_IP4_DNS_FLOOD_SZ· 153

ATK_IP4_FIN_FLOOD·· 154

ATK_IP4_FIN_FLOOD_SZ· 154

ATK_IP4_FRAGMENT· 155

ATK_IP4_FRAGMENT_RAW·· 156

ATK_IP4_FRAGMENT_RAW_SZ· 157

ATK_IP4_FRAGMENT_SZ· 158

ATK_IP4_HTTP_FLOOD·· 159

ATK_IP4_HTTP_FLOOD_SZ· 159

ATK_IP4_IMPOSSIBLE· 160

ATK_IP4_IMPOSSIBLE_RAW·· 161

ATK_IP4_IMPOSSIBLE_RAW_SZ· 162

ATK_IP4_IMPOSSIBLE_SZ· 163

ATK_IP4_IPSWEEP· 164

ATK_IP4_IPSWEEP_SZ· 164

ATK_IP4_PORTSCAN· 165

ATK_IP4_PORTSCAN_SZ· 165

ATK_IP4_RST_FLOOD·· 166

ATK_IP4_RST_FLOOD_SZ· 166

ATK_IP4_SYN_FLOOD·· 167

ATK_IP4_SYN_FLOOD_SZ· 167

ATK_IP4_SYNACK_FLOOD·· 168

ATK_IP4_SYNACK_FLOOD_SZ· 168

ATK_IP4_TCP_ALLFLAGS· 169

ATK_IP4_TCP_ALLFLAGS_RAW·· 170

ATK_IP4_TCP_ALLFLAGS_RAW_SZ· 170

ATK_IP4_TCP_ALLFLAGS_SZ· 171

ATK_IP4_TCP_FINONLY· 172

ATK_IP4_TCP_FINONLY_RAW·· 173

ATK_IP4_TCP_FINONLY_RAW_SZ· 173

ATK_IP4_TCP_FINONLY_SZ· 174

ATK_IP4_TCP_INVALIDFLAGS· 175

ATK_IP4_TCP_INVALIDFLAGS_RAW·· 176

ATK_IP4_TCP_INVALIDFLAGS_RAW_SZ· 177

ATK_IP4_TCP_INVALIDFLAGS_SZ· 178

ATK_IP4_TCP_LAND·· 179

ATK_IP4_TCP_LAND_RAW·· 180

ATK_IP4_TCP_LAND_RAW_SZ· 180

ATK_IP4_TCP_LAND_SZ· 181

ATK_IP4_TCP_NULLFLAG·· 182

ATK_IP4_TCP_NULLFLAG_RAW·· 183

ATK_IP4_TCP_NULLFLAG_RAW_SZ· 183

ATK_IP4_TCP_NULLFLAG_SZ· 184

ATK_IP4_TCP_SYNFIN· 185

ATK_IP4_TCP_SYNFIN_RAW·· 186

ATK_IP4_TCP_SYNFIN_RAW_SZ· 186

ATK_IP4_TCP_SYNFIN_SZ· 187

ATK_IP4_TCP_WINNUKE· 188

ATK_IP4_TCP_WINNUKE_RAW·· 189

ATK_IP4_TCP_WINNUKE_RAW_SZ· 189

ATK_IP4_TCP_WINNUKE_SZ· 190

ATK_IP4_TEARDROP· 191

ATK_IP4_TEARDROP_RAW·· 192

ATK_IP4_TEARDROP_RAW_SZ· 193

ATK_IP4_TEARDROP_SZ· 194

ATK_IP4_TINY_FRAGMENT· 195

ATK_IP4_TINY_FRAGMENT_RAW·· 196

ATK_IP4_TINY_FRAGMENT_RAW_SZ· 197

ATK_IP4_TINY_FRAGMENT_SZ· 198

ATK_IP4_UDP_BOMB· 199

ATK_IP4_UDP_BOMB_RAW·· 200

ATK_IP4_UDP_BOMB_RAW_SZ· 201

ATK_IP4_UDP_BOMB_SZ· 202

ATK_IP4_UDP_FLOOD·· 203

ATK_IP4_UDP_FLOOD_SZ· 203

ATK_IP4_UDP_FRAGGLE· 204

ATK_IP4_UDP_FRAGGLE_RAW·· 205

ATK_IP4_UDP_FRAGGLE_RAW_SZ· 205

ATK_IP4_UDP_FRAGGLE_SZ· 206

ATK_IP4_UDP_SNORK· 207

ATK_IP4_UDP_SNORK_RAW·· 208

ATK_IP4_UDP_SNORK_RAW_SZ· 208

ATK_IP4_UDP_SNORK_SZ· 209

ATK_IP6_ACK_FLOOD·· 210

ATK_IP6_ACK_FLOOD_SZ· 210

ATK_IP6_DIS_PORTSCAN· 211

ATK_IP6_DIS_PORTSCAN_SZ· 211

ATK_IP6_DNS_FLOOD·· 212

ATK_IP6_DNS_FLOOD_SZ· 212

ATK_IP6_FIN_FLOOD·· 213

ATK_IP6_FIN_FLOOD_SZ· 213

ATK_IP6_FRAGMENT· 214

ATK_IP6_FRAGMENT_RAW·· 215

ATK_IP6_FRAGMENT_RAW_SZ· 215

ATK_IP6_FRAGMENT_SZ· 216

ATK_IP6_HTTP_FLOOD·· 217

ATK_IP6_HTTP_FLOOD_SZ· 217

ATK_IP6_IMPOSSIBLE· 218

ATK_IP6_IMPOSSIBLE_RAW·· 219

ATK_IP6_IMPOSSIBLE_RAW_SZ· 219

ATK_IP6_IMPOSSIBLE_SZ· 220

ATK_IP6_IPSWEEP· 220

ATK_IP6_IPSWEEP_SZ· 221

ATK_IP6_PORTSCAN· 221

ATK_IP6_PORTSCAN_SZ· 222

ATK_IP6_RST_FLOOD·· 222

ATK_IP6_RST_FLOOD_SZ· 223

ATK_IP6_SYN_FLOOD·· 223

ATK_IP6_SYN_FLOOD_SZ· 224

ATK_IP6_SYNACK_FLOOD·· 224

ATK_IP6_SYNACK_FLOOD_SZ· 225

ATK_IP6_TCP_ALLFLAGS· 225

ATK_IP6_TCP_ALLFLAGS_RAW·· 226

ATK_IP6_TCP_ALLFLAGS_RAW_SZ· 226

ATK_IP6_TCP_ALLFLAGS_SZ· 227

ATK_IP6_TCP_FINONLY· 228

ATK_IP6_TCP_FINONLY_RAW·· 228

ATK_IP6_TCP_FINONLY_RAW_SZ· 229

ATK_IP6_TCP_FINONLY_SZ· 229

ATK_IP6_TCP_INVALIDFLAGS· 230

ATK_IP6_TCP_INVALIDFLAGS_RAW·· 231

ATK_IP6_TCP_INVALIDFLAGS_RAW_SZ· 232

ATK_IP6_TCP_INVALIDFLAGS_SZ· 233

ATK_IP6_TCP_LAND·· 234

ATK_IP6_TCP_LAND_RAW·· 234

ATK_IP6_TCP_LAND_RAW_SZ· 235

ATK_IP6_TCP_LAND_SZ· 235

ATK_IP6_TCP_NULLFLAG·· 236

ATK_IP6_TCP_NULLFLAG_RAW·· 236

ATK_IP6_TCP_NULLFLAG_RAW_SZ· 237

ATK_IP6_TCP_NULLFLAG_SZ· 237

ATK_IP6_TCP_SYNFIN· 238

ATK_IP6_TCP_SYNFIN_RAW·· 238

ATK_IP6_TCP_SYNFIN_RAW_SZ· 239

ATK_IP6_TCP_SYNFIN_SZ· 239

ATK_IP6_TCP_WINNUKE· 240

ATK_IP6_TCP_WINNUKE_RAW·· 240

ATK_IP6_TCP_WINNUKE_RAW_SZ· 241

ATK_IP6_TCP_WINNUKE_SZ· 241

ATK_IP6_UDP_FLOOD·· 242

ATK_IP6_UDP_FLOOD_SZ· 242

ATK_IP6_UDP_FRAGGLE· 243

ATK_IP6_UDP_FRAGGLE_RAW·· 243

ATK_IP6_UDP_FRAGGLE_RAW_SZ· 244

ATK_IP6_UDP_FRAGGLE_SZ· 244

ATK_IP6_UDP_SNORK· 245

ATK_IP6_UDP_SNORK_RAW·· 245

ATK_IP6_UDP_SNORK_RAW_SZ· 246

ATK_IP6_UDP_SNORK_SZ· 246

ATK_IPOPT_ABNORMAL· 247

ATK_IPOPT_ABNORMAL_RAW·· 248

ATK_IPOPT_ABNORMAL_RAW_SZ· 249

ATK_IPOPT_ABNORMAL_SZ· 250

ATK_IPOPT_LOOSESRCROUTE· 251

ATK_IPOPT_LOOSESRCROUTE_RAW·· 252

ATK_IPOPT_LOOSESRCROUTE_RAW_SZ· 253

ATK_IPOPT_LOOSESRCROUTE_SZ· 254

ATK_IPOPT_RECORDROUTE· 255

ATK_IPOPT_RECORDROUTE_RAW·· 256

ATK_IPOPT_RECORDROUTE_RAW_SZ· 257

ATK_IPOPT_RECORDROUTE_SZ· 258

ATK_IPOPT_ROUTEALERT· 259

ATK_IPOPT_ROUTEALERT_RAW·· 260

ATK_IPOPT_ROUTEALERT_RAW_SZ· 261

ATK_IPOPT_ROUTEALERT_SZ· 262

ATK_IPOPT_SECURITY· 263

ATK_IPOPT_SECURITY_RAW·· 264

ATK_IPOPT_SECURITY_RAW_SZ· 265

ATK_IPOPT_SECURITY_SZ· 266

ATK_IPOPT_STREAMID·· 267

ATK_IPOPT_STREAMID_RAW·· 268

ATK_IPOPT_STREAMID_RAW_SZ· 269

ATK_IPOPT_STREAMID_SZ· 270

ATK_IPOPT_STRICTSRCROUTE· 271

ATK_IPOPT_STRICTSRCROUTE_RAW·· 272

ATK_IPOPT_STRICTSRCROUTE_RAW_SZ· 273

ATK_IPOPT_STRICTSRCROUTE_SZ· 274

ATK_IPOPT_TIMESTAMP· 275

ATK_IPOPT_TIMESTAMP_RAW·· 276

ATK_IPOPT_TIMESTAMP_RAW_SZ· 277

ATK_IPOPT_TIMESTAMP_SZ· 278

ATK_IPV6_EXT_HEADER· 279

ATK_IPV6_EXT_HEADER_RAW·· 280

ATK_IPV6_EXT_HEADER_RAW_SZ· 280

ATK_IPV6_EXT_HEADER_SZ· 281

ATM·· 282

ATM_PVCDOWN· 282

ATM_PVCUP· 282

BFD messages· 284

BFD_CHANGE_FSM·· 284

BFD_REACHED_UPPER_LIMIT· 284

BGP messages· 285

BGP_EXCEED_ROUTE_LIMIT· 285

BGP_REACHED_THRESHOLD·· 285

BGP_LOG_ROUTE_FLAP· 286

BGP_MEM_ALERT· 286

BGP_PEER_LICENSE_REACHED·· 286

BGP_ROUTE_LICENSE_REACHED·· 287

BGP_STATE_CHANGED·· 287

BLS messages· 288

BLS_ENTRY_ADD·· 288

BLS_ENTRY_DEL· 288

BLS_IPV6_ENTRY_ADD·· 289

BLS_IPV6_ENTRY_DEL· 289

CFD messages· 290

CFD_CROSS_CCM·· 290

CFD_ERROR_CCM·· 290

CFD_LOST_CCM·· 291

CFD_RECEIVE_CCM·· 291

CFGMAN messages· 292

CFGMAN_ARCHIVE_SCP_FAIL· 292

CFGMAN_CFGCHANGED·· 292

CFGMAN_EXIT_FROM_CONFIGURE· 293

CFGMAN_OPTCOMPLETION· 293

CONNLMT messages· 295

CONNLMT_IPV4_OVERLOAD·· 295

CONNLMT_IPV4_RECOVER· 296

CONNLMT_IPV6_OVERLOAD·· 297

CONNLMT_IPV6_RECOVER· 298

DEV messages· 299

BOARD_REBOOT· 299

BOARD_REMOVED·· 299

BOARD_STATE_FAULT· 300

BOARD_STATE_NORMAL· 300

CFCARD_INSERTED·· 300

CFCARD_REMOVED·· 301

CHASSIS_REBOOT· 301

DEV_CLOCK_CHANGE· 301

DEV_FAULT_TOOLONG·· 302

DEV_MNT_LogToIC· 302

DYINGGASP· 302

FAN_ABSENT· 303

FAN_DIRECTION_NOT_PREFERRED·· 303

FAN_FAILED·· 304

FAN_RECOVERED·· 304

MAD_DETECT· 305

POWER_ABSENT· 305

POWER_FAILED·· 306

POWER_MONITOR_ABSENT· 306

POWER_MONITOR_FAILED·· 307

POWER_MONITOR_RECOVERED·· 307

POWER_RECOVERED·· 308

RPS_ABSENT· 308

RPS_FAILED·· 309

RPS_NORMAL· 309

SUBCARD_FAULT· 310

SUBCARD_INSERTED·· 310

SUBCARD_REBOOT· 311

SUBCARD_REMOVED·· 311

SYSTEM_REBOOT· 311

TEMPERATURE_ALARM·· 312

TEMPERATURE_LOW·· 313

TEMPERATURE_NORMAL· 314

TEMPERATURE_SHUTDOWN· 315

TEMPERATURE_WARNING·· 316

VCHK_VERSION_INCOMPATIBLE· 316

DHCP·· 317

DHCP_NOTSUPPORTED·· 317

DHCP_NORESOURCES· 317

DHCPR·· 318

DHCPR_SERVERCHANGE· 318

DHCPR_SWITCHMASTER· 318

DHCPS messages· 319

DHCPS_ALLOCATE_IP· 319

DHCPS_CONFLICT_IP· 319

DHCPS_EXTEND_IP· 320

DHCPS_FILE· 320

DHCPS_RECLAIM_IP· 321

DHCPS_VERIFY_CLASS· 321

DHCPS6 messages· 322

DHCPS6_ALLOCATE_ADDRESS· 322

DHCPS6_ALLOCATE_PREFIX· 322

DHCPS6_CONFLICT_ADDRESS· 323

DHCPS6_EXTEND_ADDRESS· 323

DHCPS6_EXTEND_PREFIX· 324

DHCPS6_FILE· 324

DHCPS6_RECLAIM_ADDRESS· 325

DHCPS6_RECLAIM_PREFIX· 325

DHCPSP4· 326

DHCPSP4_FILE· 326

DHCPSP6· 327

DHCPSP6_FILE· 327

DIAG messages· 328

CPU_MINOR_RECOVERY· 328

CPU_MINOR_THRESHOLD·· 328

CPU_SEVERE_RECOVERY· 328

CPU_SEVERE_THRESHOLD·· 329

MEM_ALERT· 330

MEM_BELOW_THRESHOLD·· 331

MEM_EXCEED_THRESHOLD·· 331

DLDP messages· 332

DLDP_AUTHENTICATION_FAILED·· 332

DLDP_LINK_BIDIRECTIONAL· 332

DLDP_LINK_SHUTMODECHG·· 333

DLDP_LINK_UNIDIRECTIONAL· 333

DLDP_NEIGHBOR_AGED·· 334

DLDP_NEIGHBOR_CONFIRMED·· 334

DLDP_NEIGHBOR_DELETED·· 335

DOT1X messages· 336

DOT1X_CONFIG_NOTSUPPORT· 336

DOT1X_LOGIN_FAILURE· 336

DOT1X_LOGIN_SUCC· 337

DOT1X_LOGIN_SUCC (in open mode) 337

DOT1X_LOGOFF· 338

DOT1X_LOGOFF (in open mode) 338

DOT1X_LOGOFF_ABNORMAL· 339

DOT1X_LOGOFF_ABNORMAL (in open mode) 339

DOT1X_MACBINDING_EXIST· 340

DOT1X_NOTENOUGH_EADFREEIP_RES· 340

DOT1X_NOTENOUGH_EADFREERULE_RES· 341

DOT1X_NOTENOUGH_EADMACREDIR_RES· 341

DOT1X_NOTENOUGH_EADPORTREDIR_RES· 341

DOT1X_NOTENOUGH_ENABLEDOT1X_RES· 342

DOT1X_PEXAGG_NOMEMBER_RES· 342

DOT1X_SMARTON_FAILURE· 342

DOT1X_UNICAST_NOT_EFFECTIVE· 343

DRNI 344

DRNI_AUTO-RECOVERY_TIMEOUT· 344

DRNI_GLBCONSISTENCYCHECK_SUCCESS· 344

DRNI_GLBCONSISTENCYCHECK_FAILURE· 345

DRNI_IFCONSISTENCYCHECK_SUCCESS· 345

DRNI_IFCONSISTENCYCHECK_FAILURE· 345

DRNI_IFEVENT_DR_BIND·· 346

DRNI_IFEVENT_DR_GLOBALDOWN· 346

DRNI_IFEVENT_DR_GLOBALUP· 346

DRNI_IFEVENT_DR_NOSELECTED·· 347

DRNI_IFEVENT_DR_PEER_NOSELECTED·· 347

DRNI_IFEVENT_DR_PEER_SELECTED·· 347

DRNI_IFEVENT_DR_SELECTED·· 348

DRNI_IFEVENT_DR_UNBIND·· 348

DRNI_IFEVENT_IPP_BIND·· 348

DRNI_IFEVENT_IPP_DOWN· 349

DRNI_IFEVENT_IPP_UNBIND·· 349

DRNI_IFEVENT_IPP_UP· 349

DRNI_IPP_BLOCK· 350

DRNI_IPP_UNBLOCK· 350

DRNI_KEEPALIVEINTERVAL_MISMATCH· 350

DRNI_KEEPALIVELINK_DOWN· 351

DRNI_KEEPALIVELINK_UP· 351

DRNI_SECONDARY_MADDOWN· 351

DRNI_SYSEVENT_DEVICEROLE_CHANGE· 352

DRNI_SYSEVENT_MAC_CHANGE· 352

DRNI_SYSEVENT_NUMBER_CHANGE· 352

DRNI_SYSEVENT_PRIORITY_CHANGE· 353

DRV·· 354

DRV_CLK· 354

DRV_DEVM·· 355

DRV_PTP· 355

DRVPLAT· 357

DRVPLAT_COPP_FAIL· 357

DRVPLAT_ECMP_NO_RESOURCE· 357

DRVPLAT_MAC_Confilict 358

DRVPLAT_NO_ENOUGH_RESOURCE· 358

DRVPLAT_POE_AI_DISCONNET_AC· 358

DRVPLAT_POE_AI_DISCONNET_DELAY· 359

DRVPLAT_POE_AI_HIGH_INRUSH· 359

DRVPLAT_POE_AI_PORT_MAXPOWER· 360

DRVPLAT_POE_AI_PORT_RESTART· 361

DRVPLAT_PORT· 361

361

362

362

362

362

363

363

363

363

364

DRVPLAT_PORT_ATTACK_OCCUR· 364

DRVPLAT_PORT_MAXPOWER_FORCE_POWER_OFF· 365

365

DRVPLAT_PSE_POWER_FORCE_POWER_ON· 366

DRVPLAT_SOFTCAR_DROP· 366

EDEV messages· 367

ALARM_IN_REMOVED·· 367

ALARM_IN_REPORTED·· 367

EDEV_BOOTROM_UPDATE_FAILED·· 367

EDEV_BOOTROM_UPDATE_SUCCESS· 368

EDEV_FAILOVER_GROUP_STATE_CHANGE· 368

EPA messages· 369

EPA_ENDPOINT_ONLINE· 369

EPA_ENDPOINT_OFFLINE· 369

EPA_DEVICETYPE_CHANGE· 370

ERPS messages· 371

ERPS_STATE_CHANGED·· 371

ETH messages· 372

ETH_SET_MAC_FAILED·· 372

ETHOAM messages· 373

ETHOAM_CONNECTION_FAIL_DOWN· 373

ETHOAM_CONNECTION_FAIL_TIMEOUT· 373

ETHOAM_CONNECTION_FAIL_UNSATISF· 374

ETHOAM_CONNECTION_SUCCEED·· 374

ETHOAM_DISABLE· 374

ETHOAM_DISCOVERY_EXIT· 375

ETHOAM_ENABLE· 375

ETHOAM_ENTER_LOOPBACK_CTRLLED·· 375

ETHOAM_ENTER_LOOPBACK_CTRLLING·· 376

ETHOAM_LOCAL_DYING_GASP· 376

ETHOAM_LOCAL_ERROR_FRAME· 376

ETHOAM_LOCAL_ERROR_FRAME_PERIOD·· 377

ETHOAM_LOCAL_ERROR_FRAME_SECOND·· 377

ETHOAM_LOCAL_ERROR_SYMBOL· 377

ETHOAM_LOCAL_LINK_FAULT· 378

ETHOAM_LOOPBACK_EXIT· 378

ETHOAM_LOOPBACK_EXIT_ERROR_STATU· 378

ETHOAM_LOOPBACK_NO_RESOURCE· 379

ETHOAM_LOOPBACK_NOT_SUPPORT· 379

ETHOAM_QUIT_LOOPBACK_CTRLLED·· 379

ETHOAM_QUIT_LOOPBACK_CTRLLING·· 380

ETHOAM_REMOTE_CRITICAL· 380

ETHOAM_REMOTE_DYING_GASP· 380

ETHOAM_REMOTE_ERROR_FRAME· 381

ETHOAM_REMOTE_ERROR_FRAME_PERIOD·· 381

ETHOAM_REMOTE_ERROR_FRAME_SECOND·· 381

ETHOAM_REMOTE_ERROR_SYMBOL· 382

ETHOAM_REMOTE_EXIT· 382

ETHOAM_REMOTE_FAILURE_RECOVER· 382

ETHOAM_REMOTE_LINK_FAULT· 383

ETHOAM_NO_ENOUGH_RESOURCE· 383

ETHOAM_NOT_CONNECTION_TIMEOUT· 383

EVB messages· 384

EVB_AGG_FAILED·· 384

EVB_LICENSE_EXPIRE· 384

EVB_VSI_OFFLINE· 385

EVB_VSI_ONLINE· 385

EVIISIS messages· 386

EVIISIS_LICENSE_EXPIRED·· 386

EVIISIS_LICENSE_EXPIRED_TIME· 386

EVIISIS_LICENSE_UNAVAILABLE· 386

EVIISIS_NBR_CHG·· 387

FCLINK messages· 388

FCLINK_FDISC_REJECT_NORESOURCE· 388

FCLINK_FLOGI_REJECT_NORESOURCE· 388

FCOE messages· 389

FCOE_INTERFACE_NOTSUPPORT_FCOE· 389

FCOE_LAGG_BIND_ACTIVE· 389

FCOE_LAGG_BIND_DEACTIVE· 390

FCZONE messages· 391

FCZONE_DISTRIBUTE_FAILED·· 391

FCZONE_HARDZONE_DISABLED·· 391

FCZONE_HARDZONE_ENABLED·· 392

FCZONE_ISOLATE_ALLNEIGHBOR· 392

FCZONE_ISOLATE_CLEAR_VSAN· 393

FCZONE_ISOLATE_CLEAR_ALLVSAN· 393

FCZONE_ISOLATE_NEIGHBOR· 393

FIB messages· 394

FIB_FILE· 394

FILTER messages· 395

FILTER_EXECUTION_ICMP· 395

FILTER_EXECUTION_ICMPV6· 396

FILTER_IPV4_EXECUTION· 397

FILTER_IPV6_EXECUTION· 398

FIPSNG messages· 399

FIPSNG_HARD_RESOURCE_NOENOUGH· 399

FIPSNG_HARD_RESOURCE_RESTORE· 399

FS messages· 400

FS_UNFORMATTED_PARTITION· 400

FTP messages· 401

FTP_ACL_DENY· 401

FTP_REACH_SESSION_LIMIT· 401

FTPD_AUTHOR_FAILED·· 402

gRPC messages· 403

GRPC_LOGIN· 403

GRPC_LOGIN_FAILED·· 403

GRPC_LOGOUT· 404

GRPC_SERVER_FAILED·· 404

GRPC_SUBSCRIBE_EVENT_FAILED·· 404

GRPC_RECEIVE_SUBSCRIPTION· 405

HA messages· 406

HA_BATCHBACKUP_FINISHED·· 406

HA_BATCHBACKUP_STARTED·· 406

HA_STANDBY_NOT_READY· 406

HA_STANDBY_TO_MASTER· 407

HQOS messages· 408

HQOS_DP_SET_FAIL· 408

HQOS_FP_SET_FAIL· 408

HQOS_POLICY_APPLY_FAIL· 409

HQOS_POLICY_APPLY_FAIL· 409

HTTPD messages· 410

HTTPD_CONNECT· 410

HTTPD_CONNECT_TIMEOUT· 410

HTTPD_DISCONNECT· 411

HTTPD_FAIL_FOR_ACL· 411

HTTPD_FAIL_FOR_ACP· 411

HTTPD_REACH_CONNECT_LIMIT· 412

IFNET messages· 413

IF_BUFFER_CONGESTION_OCCURRENCE· 413

IF_BUFFER_CONGESTION_CLEAR· 413

IF_JUMBOFRAME_WARN· 414

IF_LINKFLAP_DETECTED·· 414

INTERFACE_NOTSUPPRESSED·· 414

INTERFACE_SUPPRESSED·· 415

LINK_UPDOWN· 415

PFC_WARNING·· 416

PHY_UPDOWN· 416

PROTOCOL_UPDOWN· 416

STORM_CONSTRAIN_BELOW·· 417

STORM_CONSTRAIN_CONTROLLED·· 417

STORM_CONSTRAIN_EXCEED·· 418

STORM_CONSTRAIN_NORMAL· 418

TUNNEL_LINK_UPDOWN· 419

TUNNEL_PHY_UPDOWN· 419

VLAN_MODE_CHANGE· 419

IKE messages· 420

IKE_P1_SA_ESTABLISH_FAIL· 420

IKE_P2_SA_ESTABLISH_FAIL· 421

IKE_P2_SA_TERMINATE· 421

IKE_VERIFY_CERT_FAIL· 422

IP6ADDR·· 424

IP6ADDR_CREATEADDRESS_ERROR· 424

IP6ADDR_FUNCTION_FAIL· 424

IPADDR messages· 425

IPADDR_HA_EVENT_ERROR· 425

IPADDR_HA_STOP_EVENT· 426

IPFW··· 427

IPFW_FAILURE· 427

IPSEC messages· 428

IPSEC_FAILED_ADD_FLOW_TABLE· 428

IPSEC_PACKET_DISCARDED·· 428

IPSEC_SA_ESTABLISH· 429

IPSEC_SA_ESTABLISH_FAIL· 429

IPSEC_SA_INITINATION· 430

IPSEC_SA_TERMINATE· 430

IPSG messages· 431

IPSG_ADDENTRY_ERROR· 431

IPSG_ADDEXCLUDEDVLAN_ERROR· 432

IPSG_ARP_LOCALMAC_CONFLICT· 432

IPSG_ARP_REMOTEMAC_CONFLICT· 433

IPSG_DELENTRY_ERROR· 434

IPSG_DELEXCLUDEDVLAN_ERROR· 434

IPSG_IPV4_ALARMCLEAR· 435

IPSG_IPV4_ALARMEMERGE· 435

IPSG_IPV6_ALARMCLEAR· 435

IPSG_IPV6_ALARMEMERGE· 436

IPSG_MAC_CONFLICT· 436

IPSG_ND_LOCALMAC_CONFLICT· 437

IPSG_ND_REMOTEMAC_CONFLICT· 437

IRDP messages· 438

IRDP_EXCEED_ADVADDR_LIMIT· 438

IRF· 439

IRF_LINK_BLOCK· 439

IRF_LINK_DOWN· 439

IRF_LINK_UP· 439

IRF_MEMBERID_CONFLICT· 440

IRF_MERGE· 440

IRF_MERGE_NEED_REBOOT· 440

IRF_MERGE_NOT_NEED_REBOOT· 441

ISIS messages· 442

ISIS_LSP_CONFLICT· 442

ISIS_MEM_ALERT· 442

ISIS_NBR_CHG·· 443

ISSU messages· 444

ISSU_LOAD_FAILED·· 444

ISSU_LOAD_SUCCESS· 444

ISSU_PROCESSWITCHOVER· 444

ISSU_ROLLBACKCHECKNORMAL· 445

L2PT messages· 446

L2PT_SET_MULTIMAC_FAILED·· 446

L2PT_CREATE_TUNNELGROUP_FAILED·· 446

L2PT_ADD_GROUPMEMBER_FAILED·· 446

L2PT_ENABLE_DROP_FAILED·· 447

L2TPv2 messages· 448

L2TPV2_TUNNEL_EXCEED_LIMIT· 448

L2TPV2_SESSION_EXCEED_LIMIT· 448

L2VPN messages· 449

L2VPN_BGPVC_CONFLICT_LOCAL· 449

L2VPN_BGPVC_CONFLICT_REMOTE· 449

L2VPN_HARD_RESOURCE_NOENOUGH· 450

L2VPN_HARD_RESOURCE_RESTORE· 450

L2VPN_LABEL_DUPLICATE· 450

LAGG messages· 451

LAGG_ACTIVE· 451

LAGG_AUTO_AGGREGATION· 451

LAGG_INACTIVE_AICFG·· 452

LAGG_INACTIVE_BFD·· 452

LAGG_INACTIVE_CONFIGURATION· 453

LAGG_INACTIVE_DUPLEX· 453

LAGG_INACTIVE_HARDWAREVALUE· 454

LAGG_INACTIVE_LOWER_LIMIT· 454

LAGG_INACTIVE_PARTNER· 455

LAGG_INACTIVE_PHYSTATE· 455

LAGG_INACTIVE_RESOURCE_INSUFICIE· 456

LAGG_INACTIVE_SPEED·· 456

LAGG_INACTIVE_UPPER_LIMIT· 457

LAGG_SELECTPORT_INCONSISTENT· 457

LDP messages· 458

LDP_MPLSLSRID_CHG·· 458

LDP_SESSION_CHG·· 459

LDP_SESSION_GR· 460

LDP_SESSION_SP· 460

LLDP messages· 461

LLDP_CREATE_NEIGHBOR· 461

LLDP_DELETE_NEIGHBOR· 462

LLDP_LESS_THAN_NEIGHBOR_LIMIT· 462

LLDP_NEIGHBOR_AGE_OUT· 463

LLDP_NEIGHBOR_PROTECTION_BLOCK· 463

LLDP_NEIGHBOR_PROTECTION_DOWN· 464

LLDP_NEIGHBOR_PROTECTION_UNBLOCK· 464

LLDP_NEIGHBOR_PROTECTION_UP· 464

LLDP_PVID_INCONSISTENT· 465

LLDP_REACH_NEIGHBOR_LIMIT· 465

LOAD messages· 466

BOARD_LOADING·· 466

LOAD_FAILED·· 466

LOAD_FINISHED·· 467

LOGIN messages· 468

LOGIN_FAILED·· 468

LOGIN_ INVALID_USERNAME_PWD·· 468

LPDT messages· 469

LPDT_LOOPED·· 469

LPDT_RECOVERED·· 469

LPDT_VLAN_LOOPED·· 469

LPDT_VLAN_RECOVERED·· 470

LS messages· 471

LOCALSVR_PROMPTED_CHANGE_PWD·· 471

LS_ADD_USER_TO_GROUP· 471

LS_AUTHEN_FAILURE· 472

LS_AUTHEN_SUCCESS· 472

LS_DEL_USER_FROM_GROUP· 473

LS_DELETE_PASSWORD_FAIL· 473

LS_PWD_ADDBLACKLIST· 473

LS_PWD_CHGPWD_FOR_AGEDOUT· 474

LS_PWD_CHGPWD_FOR_AGEOUT· 474

LS_PWD_CHGPWD_FOR_COMPOSITION· 474

LS_PWD_CHGPWD_FOR_FIRSTLOGIN· 475

LS_PWD_CHGPWD_FOR_LENGTH· 475

LS_PWD_FAILED2WRITEPASS2FILE· 475

LS_PWD_MODIFY_FAIL· 476

LS_PWD_MODIFY_SUCCESS· 476

LS_REAUTHEN_FAILURE· 477

LS_UPDATE_PASSWORD_FAIL· 477

LS_USER_CANCEL· 477

LS_USER_PASSWORD_EXPIRE· 478

LS_USER_ROLE_CHANGE· 478

LSPV messages· 479

LSPV_PING_STATIS_INFO·· 479

MAC messages· 480

MAC_DRIVER_ADD_ENTRY· 480

MAC_PROTOCOLPKT_NORES_GLOBAL· 480

MAC_PROTOCOLPKT_NORES_PORT· 481

MAC_PROTOCOLPKT_NORES_VLAN· 481

MAC_TABLE_FULL_GLOBAL· 481

MAC_TABLE_FULL_PORT· 482

MAC_TABLE_FULL_VLAN· 482

MAC_VLAN_LEARNLIMIT_NORESOURCE· 482

MAC_VLAN_LEARNLIMIT_NOTSUPPORT· 483

MACA messages· 484

MACA_ENABLE_NOT_EFFECTIVE· 484

MACA_LOGIN_FAILURE· 484

MACA_LOGIN_FAILURE (EAD) 485

MACA_LOGIN_SUCC· 486

MACA_LOGIN_SUCC (in open mode) 486

MACA_LOGOFF· 487

MACA_LOGOFF (in open mode) 487

MACSEC messages· 488

MACSEC_MKA_KEEPALIVE_TIMEOUT· 488

MACSEC_MKA_PRINCIPAL_ACTOR· 488

MACSEC_MKA_SAK_REFRESH· 489

MACSEC_MKA_SESSION_REAUTH· 489

MACSEC_MKA_SESSION_SECURED·· 490

MACSEC_MKA_SESSION_START· 490

MACSEC_MKA_SESSION_STOP· 491

MACSEC_MKA_SESSION_UNSECURED·· 491

MBFD messages· 492

MBFD_TRACEROUTE_FAILURE· 492

MBUF messages· 493

MBUF_DATA_BLOCK_CREATE_FAIL· 493

MDC messages· 494

MDC_CREATE_ERR· 494

MDC_CREATE· 494

MDC_DELETE· 495

MDC_KERNEL_EVENT_TOOLONG·· 495

MDC_LICENSE_EXPIRE· 495

MDC_NO_FORMAL_LICENSE· 496

MDC_NO_LICENSE_EXIT· 496

MDC_OFFLINE· 496

MDC_ONLINE· 497

MDC_STATE_CHANGE· 497

MFIB messages· 498

MFIB_MEM_ALERT· 498

MGROUP messages· 499

MGROUP_APPLY_SAMPLER_FAIL· 499

MGROUP_RESTORE_CPUCFG_FAIL· 499

MGROUP_RESTORE_GROUP_FAIL· 500

MGROUP_RESTORE_IFCFG_FAIL· 500

MGROUP_SYNC_CFG_FAIL· 501

MPLS messages· 502

MPLS_HARD_RESOURCE_NOENOUGH· 502

MPLS_HARD_RESOURCE_RESTORE· 502

MTLK messages· 503

MTLK_UPLINK_STATUS_CHANGE· 503

NAT messages· 504

NAT_ADDR_BIND_CONFLICT· 504

NAT_FAILED_ADD_FLOW_RULE· 504

NAT_FAILED_ADD_FLOW_TABLE· 505

NAT_FLOW·· 506

NAT_SERVER_INVALID·· 507

NAT_SERVICE_CARD_RECOVER_FAILURE· 508

ND messages· 509

ND_COMMONPROXY_ENABLE_FAILED·· 509

ND_CONFLICT· 509

ND_DUPADDR· 510

ND_HOST_IP_CONFLICT· 510

ND_LOCALPROXY_ENABLE_FAILED·· 510

ND_MAC_CHECK· 511

ND_NETWORKROUTE_DUPLICATE· 511

ND_RAGUARD_DROP· 512

ND_SET_PORT_TRUST_NORESOURCE· 512

ND_SET_VLAN_REDIRECT_NORESOURCE· 512

ND_SNOOPING_LEARN_ALARM·· 513

ND_SNOOPING_LEARN_ALARM_RECOVER· 513

ND_USER_DUPLICATE_IPV6ADDR· 514

ND_USER_MOVE· 515

ND_USER_OFFLINE· 515

ND_USER_ONLINE· 516

NETCONF messages· 517

CLI 517

EDIT-CONFIG·· 518

NETCONF_MSG_DEL· 519

THREAD·· 519

NQA messages· 520

NQA_LOG_UNREACHABLE· 520

NTP messages· 521

NTP_CLOCK_CHANGE· 521

NTP_LEAP_CHANGE· 521

NTP_SOURCE_CHANGE· 522

NTP_SOURCE_LOST· 522

NTP_STRATUM_CHANGE· 522

OAP messages· 523

OAP_CLIENT_DEREG·· 523

OAP_CLIENT_TIMEOUT· 523

OBJP messages· 524

OBJP_ACCELERATE_NO_RES· 524

OBJP_ACCELERATE_NOT_SUPPORT· 524

OBJP_ACCELERATE_UNK_ERR· 525

OFP messages· 526

OFP_ACTIVE· 526

OFP_ACTIVE_FAILED·· 526

OFP_CONNECT· 526

OFP_FAIL_OPEN· 527

OFP_FAIL_OPEN_FAILED·· 527

OFP_FLOW_ADD·· 528

OFP_FLOW_ADD_ARP_FAILED·· 528

OFP_FLOW_ADD_DUP· 529

OFP_FLOW_ADD_FAILED·· 529

OFP_FLOW_ADD_FAILED·· 530

OFP_FLOW_ADD_ND_FAILED·· 530

OFP_FLOW_ADD_TABLE_MISS· 531

OFP_FLOW_ADD_TABLE_MISS_FAILED·· 531

OFP_FLOW_DEL· 532

OFP_FLOW_DEL_L2VPN_DISABLE· 532

OFP_FLOW_DEL_TABLE_MISS· 533

OFP_FLOW_DEL_TABLE_MISS_FAILED·· 533

OFP_FLOW_DEL_VXLAN_DEL· 534

OFP_FLOW_MOD·· 534

OFP_FLOW_MOD_FAILED·· 535

OFP_FLOW_MOD_TABLE_MISS· 535

OFP_FLOW_MOD_TABLE_MISS_FAILED·· 536

OFP_FLOW_RMV_GROUP· 536

OFP_FLOW_RMV_HARDTIME· 536

OFP_FLOW_RMV_IDLETIME· 537

OFP_FLOW_RMV_METER· 537

OFP_FLOW_UPDATE_FAILED·· 538

OFP_GROUP_ADD·· 538

OFP_GROUP_ADD_FAILED·· 539

OFP_GROUP_DEL· 539

OFP_GROUP_MOD·· 540

OFP_GROUP_MOD_FAILED·· 540

OFP_GROUP_REFRESH_FAILED·· 541

OFP_GROUP_ROLLBACK_FAILED·· 541

OFP_METER_ADD·· 542

OFP_METER_ADD_FAILED·· 542

OFP_METER_DEL· 543

OFP_METER_MOD·· 543

OFP_METER_MOD_FAILED·· 544

OFP_MISS_RMV_GROUP· 544

OFP_MISS_RMV_HARDTIME· 544

OFP_MISS_RMV_IDLETIME· 545

OFP_MISS_RMV_METER· 545

OFP_RADARDETECTION· 545

PORT_MOD·· 546

OPENSRC (FreeRADIUS) messages· 547

HUP event 547

Process restart event 548

Process start event 548

User authentication· 549

OPTMOD messages· 552

BIAS_HIGH· 552

BIAS_LOW·· 552

BIAS_NORMAL· 553

CFG_ERR· 553

CHKSUM_ERR· 553

IO_ERR· 554

MOD_ALM_OFF· 554

MOD_ALM_ON· 554

MODULE_IN· 555

MODULE_OUT· 555

PHONY_MODULE· 555

RX_ALM_OFF· 556

RX_ALM_ON· 556

RX_POW_HIGH· 556

RX_POW_LOW·· 557

RX_POW_NORMAL· 557

TEMP_HIGH· 557

TEMP_LOW·· 558

TEMP_NORMAL· 558

TX_ALM_OFF· 558

TX_ALM_ON· 559

TX_POW_HIGH· 559

TX_POW_LOW·· 559

TX_POW_NORMAL· 560

TYPE_ERR· 560

VOLT_HIGH· 560

VOLT_LOW·· 561

VOLT_NORMAL· 561

OSPF messages· 562

OSPF_DUP_RTRID_NBR· 562

OSPF_IP_CONFLICT_INTRA· 562

OSPF_LAST_NBR_DOWN· 563

OSPF_MEM_ALERT· 563

OSPF_NBR_CHG·· 564

OSPF_RT_LMT· 564

OSPF_RTRID_CHG·· 564

OSPF_RTRID_CONFLICT_INTER· 565

OSPF_RTRID_CONFLICT_INTRA· 565

OSPF_VLINKID_CHG·· 565

OSPFV3 messages· 566

OSPFV3_LAST_NBR_DOWN· 566

OSPFV3_MEM_ALERT· 566

OSPFV3_NBR_CHG·· 567

OSPFV3_RT_LMT· 567

PBB messages· 568

PBB_JOINAGG_WARNING·· 568

PBR messages· 569

PBR_HARDWARE_ERROR· 569

PCE messages· 570

PCE_PCEP_SESSION_CHG·· 570

PEX messages (IRF 3) 571

PEX_ASSOCIATEID_MISMATCHING·· 571

PEX_CONFIG_ERROR· 571

PEX_CONNECTION_ERROR· 572

PEX_FORBID_STACK· 572

PEX_LINK_BLOCK· 573

PEX_LINK_DOWN· 574

PEX_LINK_FORWARD·· 574

PEX_REG_JOININ· 575

PEX_REG_LEAVE· 575

PEX_REG_REQUEST· 576

PEX_STACKCONNECTION_ERROR· 576

PEX messages (IRF 3.1) 577

PEX_AUTOCONFIG_BAGG_ASSIGNMEMBER· 577

PEX_AUTOCONFIG_BAGG_CREATE· 577

PEX_AUTOCONFIG_BAGG_NORESOURCE· 578

PEX_AUTOCONFIG_BAGG_REMOVEMEMBER· 579

PEX_AUTOCONFIG_CAPABILITY_ENABLE· 579

PEX_AUTOCONFIG_CASCADELIMIT· 579

PEX_AUTOCONFIG_CONNECTION_ERROR· 580

PEX_AUTOCONFIG_DIFFGROUPNUMBER· 580

PEX_AUTOCONFIG_DYNAMICBAGG_STP· 581

PEX_AUTOCONFIG_GROUP_CREATE· 581

PEX_AUTOCONFIG_NONUMBERRESOURCE· 581

PEX_AUTOCONFIG_NOT_CASCADEPORT· 582

PEX_AUTOCONFIG_NUMBER_ASSIGN· 582

PEX_LLDP_DISCOVER· 583

PEX_MEMBERID_EXCEED·· 583

PEX_PECSP_OPEN_RCVD·· 583

PEX_PECSP_OPEN_SEND·· 584

PEX_PECSP_TIMEOUT· 584

PFILTER messages· 585

PFILTER_GLB_IPV4_DACT_NO_RES· 585

PFILTER_GLB_IPV4_DACT_UNK_ERR· 585

PFILTER_GLB_IPV6_DACT_NO_RES· 586

PFILTER_GLB_IPV6_DACT_UNK_ERR· 586

PFILTER_GLB_MAC_DACT_NO_RES· 587

PFILTER_GLB_MAC_DACT_UNK_ERR· 587

PFILTER_GLB_NO_RES· 588

PFILTER_GLB_NOT_SUPPORT· 588

PFILTER_GLB_ RES_CONFLICT· 589

PFILTER_GLB_UNK_ERR· 589

PFILTER_IF_IPV4_DACT_NO_RES· 590

PFILTER_IF_IPV4_DACT_UNK_ERR· 590

PFILTER_IF_IPV6_DACT_NO_RES· 591

PFILTER_IF_IPV6_DACT_UNK_ERR· 591

PFILTER_IF_MAC_DACT_NO_RES· 592

PFILTER_IF_MAC_DACT_UNK_ERR· 592

PFILTER_IF_NO_RES· 593

PFILTER_IF_NOT_SUPPORT· 593

PFILTER_IF_RES_CONFLICT· 594

PFILTER_IF_UNK_ERR· 594

PFILTER_IPV4_FLOW_INFO·· 595

PFILTER_IPV4_FLOW_STATIS· 595

PFILTER_IPV6_FLOW_INFO·· 596

PFILTER_IPV6_FLOW_STATIS· 596

PFILTER_IPV6_STATIS_INFO·· 597

PFILTER_MAC_FLOW_INFO·· 597

PFILTER_STATIS_INFO·· 598

PFILTER_VLAN_IPV4_DACT_NO_RES· 598

PFILTER_VLAN_IPV4_DACT_UNK_ERR· 599

PFILTER_VLAN_IPV6_DACT_NO_RES· 599

PFILTER_VLAN_IPV6_DACT_UNK_ERR· 600

PFILTER_VLAN_MAC_DACT_NO_RES· 600

PFILTER_VLAN_MAC_DACT_UNK_ERR· 601

PFILTER_VLAN_NO_RES· 601

PFILTER_VLAN_NOT_SUPPORT· 602

PFILTER_VLAN_RES_CONFLICT· 602

PFILTER_VLAN_UNK_ERR· 603

PIM messages· 604

PIM_NBR_DOWN· 604

PIM_NBR_UP· 604

PING messages· 605

PING_STATISTICS· 605

PING_VPN_STATISTICS· 606

PKG messages· 607

PKG_BOOTLOADER_FILE_FAILED·· 607

PKG_BOOTLOADER_FILE_SUCCESS· 607

PKG_INSTALL_ACTIVATE_FAILED·· 607

PKG_INSTALL_ACTIVATE_SUCCESS· 608

PKI messages· 609

GET_CERT_FROM_CA_SERVER_FAIL· 609

IMPORT_CERT_FAIL· 610

REQUEST_CERT_FAIL· 611

REQUEST_CERT_SUCCESS· 612

RETRIEVE_CRL_FAIL· 613

VALIDATE_CERT_FAIL· 614

PKT2CPU messages· 616

PKT2CPU_NO_RESOURCE· 616

PKTCPT· 617

PKTCPT_AP_OFFLINE· 617

PKTCPT_AREADY_EXIT· 617

PKTCPT_CONN_FAIL· 618

PKTCPT_INVALID_FILTER· 618

PKTCPT_LOGIN_DENIED·· 618

PKTCPT_MEMORY_ALERT· 619

PKTCPT_OPEN_FAIL· 619

PKTCPT_OPERATION_TIMEOUT· 619

PKTCPT_SERVICE_FAIL· 620

PKTCPT_UNKNOWN_ERROR· 620

PKTCPT_UPLOAD_ERROR· 621

PKTCPT_WRITE_FAIL· 621

PoE·· 622

POE_SHUTDOWN_POWEROFF· 622

POE_SHUTDOWN_POWERON· 622

Portal messages· 623

PORTAL_RULE_FAILED·· 623

PORTSEC messages· 624

PORTSEC_ACL_FAILURE· 624

PORTSEC_CAR_FAILURE· 624

PORTSEC_CREATEAC_FAILURE· 625

PORTSEC_LEARNED_MACADDR· 625

PORTSEC_NTK_NOT_EFFECTIVE· 626

PORTSEC_PORTMODE_NOT_EFFECTIVE· 626

PORTSEC_PROFILE_FAILURE· 626

PORTSEC_URL_FAILURE· 627

PORTSEC_VIOLATION· 627

PORTSEC_VLANMACLIMIT· 628

PPP messages· 629

IPPOOL_ADDRESS_EXHAUSTED·· 629

PPP_USER_LOGON_SUCCESS· 629

PPP_USER_LOGON_FAILED·· 630

PPP_USER_LOGOFF· 630

PTP messages· 632

PTP_MASTER_CLOCK_CHANGE· 632

PTP_PKTLOST· 633

PTP_PKTLOST_RECOVER· 634

PTP_PORT_BMCINFO_CHANGE· 634

PTP_PORT_STATE_CHANGE· 635

PTP_SRC_CHANGE· 636

PTP_SRC_SWITCH· 637

PTP_TIME_LOCK· 637

PTP_TIME_NOT_LOCK· 638

PTP_TIME_SYNC· 638

PTP_TIME_UNSYNC· 639

PWDCTL messages· 640

PWDCTL_ADD_BLACKLIST· 640

PWDCTL_CHANGE_PASSWORD·· 640

PWDCTL_FAILED_TO_WRITEPWD·· 641

PWDCTL_FAILED_TO_OPENFILE· 641

PWDCTL_NOENOUGHSPACE· 641

QOS messages· 642

MIRROR_SYNC_CFG_FAIL· 642

QOS_CAR_APPLYUSER_FAIL· 642

QOS_CBWFQ_REMOVED·· 643

QOS_GTS_APPLYUSER_FAIL· 643

QOS_LR_APPLYIF_FAIL· 644

QOS_NOT_ENOUGH_BANDWIDTH· 644

QOS_NOT_ENOUGH_NNIBANDWIDTH· 645

QOS_POLICY_APPLYCOPP_CBFAIL· 646

QOS_POLICY_APPLYCOPP_FAIL· 646

QOS_POLICY_APPLYGLOBAL_CBFAIL· 647

QOS_POLICY_APPLYGLOBAL_FAIL· 647

QOS_POLICY_APPLYIF_CBFAIL· 648

QOS_POLICY_APPLYIF_FAIL· 648

QOS_POLICY_APPLYUSER_FAIL· 649

QOS_POLICY_APPLYVLAN_CBFAIL· 649

QOS_POLICY_APPLYVLAN_FAIL· 650

QOS_QMPROFILE_APPLYIF_FAIL· 650

QOS_QMPROFILE_APPLYUSER_FAIL· 651

QOS_QMPROFILE_MODIFYQUEUE_FAIL· 651

QOS_QUEUE_APPLYIF_FAIL· 652

QOS_UNI_RESTORE_FAIL· 652

WRED_TABLE_CFG_FAIL· 653

RADIUS messages· 654

RADIUS_AUTH_FAILURE· 654

RADIUS_AUTH_SUCCESS· 654

RADIUS_DELETE_HOST_FAIL· 654

RDDC messages· 655

RDDC_ACTIVENODE_CHANGE· 655

RESMON·· 656

RESMON_MINOR· 656

RESMON_MINOR_RECOVERY· 657

RESMON_SEVERE· 657

RESMON_SEVERE_RECOVERY· 658

RESMON_USEDUP· 658

RESMON_USEDUP_RECOVERY· 659

RIP messages· 660

RIP_MEM_ALERT· 660

RIP_RT_LMT· 660

RIPNG messages· 661

RIPNG_MEM_ALERT· 661

RIPNG_RT_LMT· 661

RM messages· 662

RM_ACRT_REACH_LIMIT· 662

RM_ACRT_REACH_THRESVALUE· 662

RM_THRESHLD_VALUE_REACH· 663

RM_TOTAL_THRESHLD_VALUE_REACH· 663

RPR messages· 664

RPR_EXCEED_MAX_SEC_MAC· 664

RPR_EXCEED_MAX_SEC_MAC_OVER· 664

RPR_EXCEED_MAX_STATION· 665

RPR_EXCEED_MAX_STATION_OVER· 665

RPR_EXCEED_RESERVED_RATE· 665

RPR_EXCEED_RESERVED_RATE_OVER· 666

RPR_IP_DUPLICATE· 666

RPR_IP_DUPLICATE_OVER· 666

RPR_JUMBO_INCONSISTENT· 667

RPR_JUMBO_INCONSISTENT_OVER· 667

RPR_LAGGCONFIG_INCONSISTENT· 667

RPR_LAGGCONFIG_INCONSISTENT_OVER· 668

RPR_MISCABLING·· 668

RPR_MISCABLING_OVER· 668

RPR_PROTECTION_INCONSISTENT· 669

RPR_PROTECTION_INCONSISTENT_OVER· 669

RPR_SEC_MAC_DUPLICATE· 669

RPR_SEC_MAC_DUPLICATE_OVER· 670

RPR_TOPOLOGY_INCONSISTENT· 670

RPR_TOPOLOGY_INCONSISTENT_OVER· 670

RPR_TOPOLOGY_INSTABILITY· 671

RPR_TOPOLOGY_INSTABILITY_OVER· 671

RPR_TOPOLOGY_INVALID·· 671

RPR_TOPOLOGY_INVALID_OVER· 672

RRPP messages· 673

RRPP_RING_FAIL· 673

RRPP_RING_RESTORE· 673

RTM messages· 674

RTM_ENVIRONMENT· 674

RTM_TCL_NOT_EXIST· 674

RTM_TCL_MODIFY· 675

RTM_TCL_LOAD_FAILED·· 675

SAVI messages· 676

SAVI_FILTER_ENTRY_ADD·· 676

SAVI_FILTER_ENTRY_DEL· 676

SAVI_SPOOFING_DETECTED·· 677

SCMD messages· 678

PROCESS_ABNORMAL· 678

PROCESS_ACTIVEFAILED·· 678

SCM_ABNORMAL_REBOOT· 679

SCM_ABNORMAL_REBOOTMDC· 679

SCM_ABORT_RESTORE· 680

SCM_INSMOD_ADDON_TOOLONG·· 680

SCM_KERNEL_INIT_TOOLONG·· 680

SCM_KILL_PROCESS· 681

SCM_PROCESS_STARTING_TOOLONG·· 682

SCM_PROCESS_STILL_STARTING·· 683

SCM_SKIP_PROCESS· 683

SCRLSP messages· 685

SCRLSP_LABEL_DUPLICATE· 685

SESSION messages· 686

SESSION_IPV4_FLOW·· 687

SESSION_IPV6_FLOW·· 688

SFLOW messages· 690

SFLOW_HARDWARE_ERROR· 690

SHELL messages· 691

SHELL_CMD·· 691

SHELL_CMD_CONFIRM·· 691

SHELL_CMD_EXECUTEFAIL· 692

SHELL_CMD_INPUT· 692

SHELL_CMD_INPUT_TIMEOUT· 692

SHELL_CMD_INVALID_CHARACTER· 693

SHELL_CMD_MATCHFAIL· 693

SHELL_CMDDENY· 694

SHELL_CMDFAIL· 694

SHELL_COMMIT· 694

SHELL_COMMIT_DELAY· 695

SHELL_COMMIT_REDELAY· 695

SHELL_COMMIT_ROLLBACK· 695

SHELL_COMMIT_ROLLBACKDONE· 696

SHELL_COMMIT_WILLROLLBACK· 696

SHELL_CRITICAL_CMDFAIL· 696

SHELL_LOGIN· 697

SHELL_LOGOUT· 697

SLSP messages· 698

SLSP_LABEL_DUPLICATE· 698

SMLK messages· 699

SMLK_LINK_SWITCH· 699

SNMP messages· 700

SNMP_ACL_RESTRICTION· 700

SNMP_AUTHENTICATION_FAILURE· 700

SNMP_GET· 701

SNMP_INFORM_LOST· 701

SNMP_NOTIFY· 702

SNMP_SET· 703

SNMP_USM_NOTINTIMEWINDOW·· 703

SSHC messages· 704

SSHC_ALGORITHM_MISMATCH· 704

SSHC_AUTH_PASSWORD_FAIL· 704

SSHC_AUTH_PUBLICKEY_FAIL· 705

SSHC_CERT_VERIFY_FAIL· 706

SSHC_CONNECT_FAIL· 707

SSHC_DECRYPT_FAIL· 707

SSHC_DISCONNECT· 708

SSHC_ENCRYPT_FAIL· 708

SSHC_HOST_NAME_ERROR· 708

SSHC_KEY_EXCHANGE_FAIL· 709

SSHC_MAC_ERROR· 709

SSHC_PUBLICKEY_NOT_EXIST· 709

SSHC_VERSION_MISMATCH· 710

SSHS messages· 711

SSHS_ACL_DENY· 711

SSHS_ALGORITHM_MISMATCH· 711

SSHS_AUTH_EXCEED_RETRY_TIMES· 712

SSHS_AUTH_FAIL· 712

SSHS_AUTH_KBDINT_FAIL· 713

SSHS_AUTH_PWD_FAIL· 713

SSHS_AUTH_TIMEOUT· 713

SSHS_AUTH_SUCCESS· 714

SSHS_AUTHOR_FAIL· 714

SSHS_CERT_VERIFY_FAIL· 715

SSHS_CONNECT· 716

SSHS_DECRYPT_FAIL· 716

SSHS_DISCONNECT· 717

SSHS_ENCRYPT_FAIL· 717

SSHS_LOG·· 718

SSHS_MAC_ERROR· 718

SSHS_REACH_SESSION_LIMIT· 719

SSHS_REACH_USER_LIMIT· 719

SSHS_SCP_OPER· 719

SSHS_SFTP_OPER· 720

SSHS_SRV_UNAVAILABLE· 720

SSHS_VERSION_MISMATCH· 721

STAMGR messages· 722

STAMGR_ADD_FAILVLAN· 722

STAMGR_ADDBAC_INFO·· 722

STAMGR_ADDSTA_INFO·· 722

STAMGR_AUTHORACL_FAILURE· 723

STAMGR_AUTHORUSERPROFILE_FAILURE· 723

STAMGR_CLIENT_OFFLINE· 724

STAMGR_CLIENT_ONLINE· 724

STAMGR_DELBAC_INFO·· 724

STAMGR_DELSTA_INFO·· 725

STAMGR_DOT1X_LOGIN_FAILURE· 725

STAMGR_DOT1X_LOGIN_SUCC· 726

STAMGR_DOT1X_LOGOFF· 726

STAMGR_MACA_LOGIN_FAILURE· 727

STAMGR_MACA_LOGIN_SUCC· 728

STAMGR_MACA_LOGOFF· 728

STAMGR_STAIPCHANGE_INFO·· 729

STAMGR_TRIGGER_IP· 729

STM messages· 730

STM_AUTO_UPDATE_FAILED·· 730

STM_AUTO_UPDATE_FINISHED·· 731

STM_AUTO_UPDATING·· 731

STM_LINK_DOWN· 732

STM_LINK_TIMEOUT· 732

STM_LINK_UP· 732

STM_MERGE· 733

STM_MERGE_NEED_REBOOT· 733

STM_MERGE_NOT_NEED_REBOOT· 733

STM_SAMEMAC· 734

STM_SOMER_CHECK· 734

STP messages· 735

STP_BPDU_PROTECTION· 735

STP_BPDU_RECEIVE_EXPIRY· 735

STP_CONSISTENCY_CHECK· 736

STP_CONSISTENCY_RESTORATION· 736

STP_DETECTED_TC· 736

STP_DISABLE· 737

STP_DISCARDING·· 737

STP_DISPUTE· 738

STP_ENABLE· 738

STP_FORWARDING·· 739

STP_LOOP_PROTECTION· 739

STP_LOOPBACK_PROTECTION· 739

STP_NOT_ROOT· 740

STP_NOTIFIED_TC· 740

STP_PORT_TYPE_INCONSISTENCY· 740

STP_PVID_INCONSISTENCY· 741

STP_PVST_BPDU_PROTECTION· 741

STP_ROOT_PROTECTION· 741

SYSLOG messages· 743

SYSLOG_LOGFILE_FULL· 743

SYSLOG_NO_SPACE· 743

SYSLOG_RESTART· 743

SYSLOG_RTM_EVENT_BUFFER_FULL· 744

SWITCH·· 745

SWITCH_FLOW_CONTROL· 745

SWITCH_BROADCAST_SUPPRESSION· 745

SWITCH_LINK_AGGREGATION· 746

SWITCH_RRPP· 746

TACACS messages· 747

TACACS_AUTH_FAILURE· 747

TACACS_AUTH_SUCCESS· 747

TACACS_DELETE_HOST_FAIL· 747

TELNETD messages· 748

TELNETD_ACL_DENY· 748

TELNETD_REACH_SESSION_LIMIT· 748

TRILL messages· 749

TRILL_DUP_SYSTEMID·· 749

TRILL_INTF_CAPABILITY· 749

TRILL_LICENSE_EXPIRED·· 750

TRILL_LICENSE_EXPIRED_TIME· 750

TRILL_LICENSE_UNAVAILABLE· 750

TRILL_MEM_ALERT· 751

TRILL_NBR_CHG·· 751

VCF messages· 752

VCF_AGGR_CREAT· 752

VCF_AGGR_DELETE· 752

VCF_AGGR_FAILED·· 753

VCF_AUTO_ANALYZE_USERDEF· 753

VCF_AUTO_NO_USERDEF· 754

VCF_AUTO_START· 754

VCF_AUTO_STATIC_CMD·· 755

VCF_BGP· 755

VCF_DOWN_LINK· 756

VCF_FAILED_ADD_IRFPORT· 756

VCF_GET_IMAGE· 757

VCF_GET_TEMPLATE· 757

VCF_INSTALL_IMAGE· 758

VCF_IRF_FINISH· 758

VCF_IRF_FOUND·· 759

VCF_IRF_REBOOT· 759

VCF_IRF_START· 760

VCF_LOOPBACK_START· 760

VCF_LOOPBACK_START_FAILED·· 761

VCF_LOOPBACK_ALLOC· 761

VCF_LOOPBACK_NO_FREE_IP· 762

VCF_LOOPBACK_RECLAIM·· 762

VCF_REBOOT· 763

VCF_SKIP_INSTALL· 763

VCF_STATIC_CMD_ERROR· 764

VCF_UP_LINK· 764

VLAN messages· 765

VLAN_CREATEFAIL· 765

VLAN_FAILED·· 765

VLAN_QINQETHTYPE_FAILED·· 766

VLAN_VLANMAPPING_FAILED·· 766

VLAN_VLANTRANSPARENT_FAILED·· 767

VRRP messages· 768

VRRP_STATUS_CHANGE· 768

VRRP_VF_STATUS_CHANGE· 769

VRRP_VMAC_INEFFECTIVE· 769

VSRP messages· 770

VSRP_BIND_FAILED·· 770

VXLAN messages· 771

VXLAN_LICENSE_UNAVAILABLE· 771

WEB messages· 772

LOGIN· 772

LOGIN_FAILED·· 772

LOGOUT· 772

WIPS messages· 773

APFLOOD·· 773

AP_CHANNEL_CHANGE· 773

ASSOCIATEOVERFLOW·· 773

HONEYPOT· 774

HTGREENMODE· 774

MAN_IN_MIDDLE· 774

WIPS_DOS· 775

WIPS_FLOOD·· 775

WIPS_MALF· 776

WIPS_SPOOF· 777

WIPS_WEAKIV· 777

WIRELESSBRIDGE· 778

 


Introduction

This document includes the following system messages:

·     Messages specific to Release 63xx of the switch.

·     Messages for the Comware 7 software platform version based on which Release xxx was produced. Some platform system messages might not be available on the switch.

This document is intended only for managing Fixed-Port Switches. Do not use this document for any other device models.

This document assumes that the readers are familiar with data communications technologies and H3C networking products.

System log message format

By default, the system log messages use one of the following formats depending on the output destination:

·     Log host:

<PRI>TIMESTAMP Sysname %%vendorMODULE/severity/MNEMONIC: location; CONTENT

·     Destinations except for the log host:

Prefix TIMESTAMP Sysname MODULE/severity/MNEMONIC: CONTENT

 

 

NOTE:

Log message examples in this document use the format for destinations except the log host. They do not contain elements available only for the log host, including the location element.

 

Table 1 System log message elements

Element

Description

<PRI>

Priority identifier. It is calculated by using the following formula:

Priority identifier=facilityx8+severity

Where:

·     Facility is specified by using the info-center loghost command. A log host uses this parameter to identify log sources and filter log messages.

·     Severity represents the importance of the message. For more information about severity levels, see Table 2.

Prefix

Message type identifier. This element is contained in the system log messages sent to non-log-host destinations.

The element uses the following symbols to indicate message severity:

·     Percentage sign (%)—Informational and higher levels.

·     Asterisk (*)—Debug level.

TIMESTAMP

Date and time when the event occurred.

The following are commands for configuring the timestamp format:

·     Log host—Use the info-center timestamp loghost command.

·     Non-log host destinationsUse the info-center timestamp command.

Sysname

Name or IP address of the device that generated the message.

%%vendor

Manufacturer flag. This element is %%10 for H3C.

This element is contained only in messages sent to the log host.

MODULE

Name of the module that produced the message.

severity

Severity level of the message. (For more information about severity levels, see Table 2.)

MNEMONIC

Text string that uniquely identifies the system message. The maximum length is 32 characters.

location

Optional. This element identifies where the message occurred. This element is contained only in messages sent to the log host.

This element presents location information for the message in the following format:

-attribute1=x-attribute2=y…-attributeN=z

The following are examples of location attributes:

·     -MDC=XX, which represents the MDC on which the message occurred.

·     -DevIp=XXX.XXX.XXX.XXX, which represents the source IP of the message.

·     -Slot=XX, which represents the slot on which the message occurred.

·     -Chassis=XX-Slot=XX, which represents the chassis and slot on which the message occurred.

This element is separated from the message description by using a semicolon (;).

CONTENT

Text string that contains detailed information about the event or error.

For variable fields in this element, this document uses the representations in Table 3.

 

System log messages are classified into eight severity levels from 0 to 7. The lower the number, the higher the severity, as shown in Table 2.

Table 2 System log message severity levels

Level

Severity

Description

0

Emergency

The system is unusable. For example, the system authorization has expired.

1

Alert

Action must be taken immediately. For example, traffic on an interface exceeds the upper limit.

2

Critical

Critical condition. For example, the device temperature exceeds the upper limit, the power module fails, or the fan tray fails.

3

Error

Error condition. For example, the link state changes or a storage card is unplugged.

4

Warning

Warning condition. For example, an interface is disconnected, or the memory resources are used up.

5

Notification

Normal but significant condition. For example, a terminal logs in to the device, or the device reboots.

6

Informational

Informational message. For example, a command or a ping operation is executed.

7

Debug

Debugging message.

 

For variable fields in the message text, this document uses the representations in Table 3. The values are case insensitive, even though the representations are uppercase letters.

Table 3 Variable field representations

Representation

Information type

INT16

Signed 16-bit decimal number.

UINT16

Unsigned 16-bit decimal number.

INT32

Signed 32-bit decimal number.

UINT32

Unsigned 32-bit decimal number.

INT64

Signed 64-bit decimal number.

UINT64

Unsigned 64-bit decimal number.

DOUBLE

Two dot-separated signed 32-bit decimal numbers. The format is [INTEGER].[INTEGER].

HEX

Hexadecimal number.

CHAR

Single character.

STRING

Character string.

IPADDR

IP address.

MAC

MAC address.

DATE

Date.

TIME

Time.

 

Managing and obtaining system log messages

You can manage system log messages by using the information center.

By default, the information center is enabled. Log messages can be output to the console, monitor terminal, log buffer, log host, and log file.

To filter log messages, use the info-center source command to specify log output rules. A log output rule specifies the source modules and the lowest severity level of log messages that can be output to a destination. A log message is output if its severity level is higher than or equal to the specified level. For example, if you specify a severity level of 6 (informational), log messages that have a severity level from 0 to 6 are output.

For more information about using the information center, see the network management and monitoring configuration guide for the product.

Obtaining log messages from the console terminal

Access the device through the console port. Real-time log messages are displayed on the console terminal.

Obtaining log messages from a monitor terminal

Monitor terminals refer to terminals that access the device through the AUX, VTY, or TTY lines (for example, Telnet). To obtain log messages from a monitor terminal, use the following guidelines:

·     To display log messages on the monitor terminal, you must configure the terminal monitor command.

·     For monitor terminals, the lowest level of log messages that can be displayed is determined by both the terminal logging level and info-center source commands.

 

 

NOTE:

Settings for the terminal monitor and terminal logging level commands take effect only on the current login session. The default settings for the commands restore at a relogin.

 

Obtaining log messages from the log buffer

Use the display logbuffer command to display history log messages in the log buffer.

Obtaining log messages from the log file

By default, the log file feature automatically saves logs from the log file buffer to the log file every 24 hours. You can use the info-center logfile frequency command to change the automatic saving internal.

To manually save logs to the log file, use the logfile save command. The log file buffer is cleared each time a save operation is performed.

By default, you can obtain the log file from the flash:/logfile path.

To view the contents of the log file on the device, use the more command.

Obtaining log messages from a log host

Use the info-center loghost command to specify the service port number and IP address of a log host. To specify multiple log hosts, repeat the command.

For a successful log message transmission, make sure the specified port number is the same as the port number used on the log host. The default service port number is 514.

Software module list

Table 4 lists all software modules that might produce system log messages. This document uses "OPENSRC" to represent all open source modules.

Table 4 Software module list

Module name representation

Module name expansion

AAA

Authentication, Authorization and Accounting

ACL

Access Control List

ANCP

Access Node Control Protocol

APMGR

Access Point Management

ARP

Address Resolution Protocol

ATK

Attack Detection and Prevention

ATM

Asynchronous Transfer Mode

BFD

Bidirectional Forwarding Detection

BGP

Border Gateway Protocol

BLS

Blacklist

CFD

Connectivity Fault Detection

CFGMAN

Configuration Management

CONNLMT

Connection Limit

DEV

Device Management

DHCP

Dynamic Host Configuration Protocol

DHCPR

IPv4 DHCP Relay

DHCPS

DHCP Server

DHCPS6

DHCPv6 Server

DHCPSP4

DHCP Snooping

DHCPSP6

DHCPv6 Snooping

DIAG

Diagnosis

DLDP

Device Link Detection Protocol

DOT1X

802.1X

DRNI

Distributed Resilient Network Interconnect

DRVPLAT

Drive Platform

EDEV

Extended-Device Management

ERPS

Ethernet Ring Protection Switching

ETH

Ethernet

ETHOAM

Ethernet Operation, Administration and Maintenance

EVB

Edge Virtual Bridging

EVIISIS

Ethernet Virtual Interconnect Intermediate System-to-Intermediate System

FCOE

Fibre Channel Over Ethernet

FCLINK

Fibre Channel Link

FCZONE

Fibre Channel Zone

FIB

Forwarding Information Base

FILTER

Filter

FIPSNG

FIP Snooping

FS

File System

FTP

File Transfer Protocol

HA

High Availability

HQOS

Hierarchical QoS

HTTPD

Hypertext Transfer Protocol Daemon

IFNET

Interface Net Management

IKE

Internet Key Exchange

IP6ADDR

IPv6 Addressing

IPADDR

IP Addressing

IPFW

IP Forwarding

IPSEC

IP Security

IPSG

IP Source Guard

IRDP

ICMP Router Discovery Protocol

IRF

Intelligent Resilient Framework

ISIS

Intermediate System-to-Intermediate System

ISSU

In-Service Software Upgrade

L2PT

Layer 2 Protocol Tunneling

L2TPV2

Layer 2 Tunneling Protocol Version 2

L2VPN

Layer 2 VPN

LAGG

Link Aggregation

LDP

Label Distribution Protocol

LLDP

Link Layer Discovery Protocol

LOAD

Load Management

LOGIN

Login

LPDT

Loopback Detection

LS

Local Server

LSPV

LSP Verification

MAC

Media Access Control

MACA

MAC Authentication

MACSEC

MAC Security

MBFD

MPLS BFD

MBUF

Memory buffer

MDC

Multitenant Device Context

MFIB

Multicast Forwarding Information Base

MGROUP

Mirroring group

MPLS

Multiprotocol Label Switching

MTLK

Monitor Link

NAT

Network Address Translation

NETCONF

Network Configuration Protocol

ND

Neighbor Discovery

NQA

Network Quality Analyzer

NTP

Network Time Protocol

OAP

Open Application Platform

OPENSRC (FreeRADIUS)

Open Source

OBJP

Object Policy

OFP

OpenFlow Protocol

OPTMOD

Optical Module

OSPF

Open Shortest Path First

OSPFV3

Open Shortest Path First Version 3

PKTCPT

Packet Capture

PFILTER

Packet Filter

PBB

Provider Backbone Bridge

PBR

Policy-Based Routing

PCE

Path Computation Element

PEX

Port Extender

PIM

Protocol Independent Multicast

PING

Packet Internet Groper

PKI

Public Key Infrastructure

PKT2CPU

Packet to CPU

PoE

Power over Ethernet

PORTAL

Portal

PORTSEC

Port Security

PPP

Point to Point Protocol

PTP

Precision Time Protocol

PWDCTL

Password Control

QOS

Quality of Service

RADIUS

Remote Authentication Dial In User Service

RDDC

Redundancy

RIP

Routing Information Protocol

RIPNG

Routing Information Protocol Next Generation

RM

Routing Management

RPR

Resilient Packet Ring

RRPP

Rapid Ring Protection Protocol

RTM

Real-Time Event Manager

SCMD

Service Control Manager Daemon

SCRLSP

Static CRLSP

SESSION

Session

SFLOW

Sampler Flow

SHELL

Shell

SLSP

Static LSP

SMLK

Smart Link

SNMP

Simple Network Management Protocol

SSHC

Secure Shell Client

SSHS

Secure Shell Server

STAMGR

Station Management

STM

Stack Topology Management

STP

Spanning Tree Protocol

SYSEVENT

System Event

SYSLOG

System Log

TACACS

Terminal Access Controller Access Control System

TELNETD

Telnet Daemon

TRILL

Transparent Interconnect of Lots of Links

VCF

Vertical Converged Framework

VLAN

Virtual Local Area Network

VRRP

Virtual Router Redundancy Protocol

VSRP

Virtual Service Redundancy Protocol

VXLAN

Virtual eXtensible LAN

WEB

Web

WIPS

Wireless Intrusion Prevention System

 

Using this document

This document categorizes system log messages by software module. The modules are ordered alphabetically. Except for OPENSRC, the system log messages for each module are listed in alphabetic order of their mnemonic names. The OPENSRC messages are unordered because they use the same mnemonic name (SYSLOG). For each OPENSRC message, the section title uses a short description instead of the mnemonic name.

This document explains messages in tables. Table 5 describes information provided in these tables.

Table 5 Message explanation table contents

Item

Content

Example

Message text

Presents the message description.

ACL [UINT32] [STRING] [UINT64] packet(s).

Variable fields

Briefly describes the variable fields in the order that they appear in the message text.

The variable fields are numbered in the "$Number" form to help you identify their location in the message text.

$1: ACL number.

$2: ID and content of an ACL rule.

$3: Number of packets that matched the rule.

Severity level

Provides the severity level of the message.

6

Example

Provides a real message example. The examples do not include the "<PRI>TIMESTAMP Sysname %%vendor" part or the "Prefix TIMESTAMP Sysname" part, because information in this part varies with system settings.

ACL/6/ACL_STATIS_INFO: ACL 2000 rule 0 permit source 1.1.1.1 0 logging 10000 packet(s).

Explanation

Explains the message, including the event or error cause.

Number of packets that matched an ACL rule. This message is sent when the packet counter changes.

Recommended action

Provides recommended actions. For informational messages, no action is required.

No action is required.

 


AAA messages

This section contains AAA messages.

AAA_FAILURE

Message text

-AAAType=[STRING]-AAADomain=[STRING]-Service=[STRING]-UserName=[STRING]; AAA failed.

Variable fields

$1: AAA type.

$2: AAA scheme.

$3: Service.

$4: Username.

Severity level

5

Example

AAA/5/AAA_FAILURE: -AAAType=AUTHOR-AAADomain=domain1-Service=login-UserName=cwf@system; AAA failed.

Explanation

An AAA request was rejected.

The following are the common reasons:

·     No response was received from the server.

·     The username or password was incorrect.

·     The service type that the user applied for was incorrect.

Recommended action

1.     Verify that the device is correctly connected to the server.

2.     Enter the correct username and password.

3.     Verify that the server settings are the same as the settings on the device.

4.     If the problem persists, contact H3C Support.

 

AAA_LAUNCH

Message text

-AAAType=[STRING]-AAADomain=[STRING]-Service=[STRING]-UserName=[STRING]; AAA launched.

Variable fields

$1: AAA type.

$2: AAA scheme.

$3: Service.

$4: Username.

Severity level

6

Example

AAA/6/AAA_LAUNCH: -AAAType=AUTHEN-AAADomain=domain1-Service=login-UserName=cwf@system; AAA launched.

Explanation

An AAA request was received.

Recommended action

No action is required.

 

AAA_SUCCESS

Message text

-AAAType=[STRING]-AAADomain=[STRING]-Service=[STRING]-UserName=[STRING]; AAA succeeded.

Variable fields

$1: AAA type.

$2: AAA scheme.

$3: Service.

$4: Username.

Severity level

6

Example

AAA/6/AAA_SUCCESS: -AAAType=AUTHOR-AAADomain=domain1-Service=login-UserName=cwf@system; AAA succeeded.

Explanation

An AAA request was accepted.

Recommended action

No action is required.

 


ACL messages

This section contains ACL messages.

ACL_ACCELERATE_NO_RES

Message text

Failed to accelerate [STRING] ACL [UINT32]. The resources are insufficient.

Variable fields

$1: ACL type.

$2: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NO_RES: Failed to accelerate IPv6 ACL 2001. The resources are insufficient.

Explanation

Hardware resources were insufficient for accelerating an ACL.

Recommended action

Delete some rules or disabled ACL acceleration for other ACLs to release hardware resources.

 

ACL_ACCELERATE_NONCONTIGUOUSMASK

Message text

Failed to accelerate ACL [UINT32]. ACL acceleration supports only contiguous wildcard masks.

Variable fields

$1: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NONCONTIGUOUSMASK: Failed to accelerate ACL 2001. ACL acceleration supports only contiguous wildcard masks.

Explanation

ACL acceleration failed because rules containing noncontiguous wildcard masks exist in the ACL.

Recommended action

Check the ACL rules and delete the unsupported configuration.

 

ACL_ACCELERATE_NOT_SUPPORT

Message text

Failed to accelerate [STRING] ACL [UINT32]. The operation is not supported.

Variable fields

$1: ACL type.

$2: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NOT_SUPPORT: Failed to accelerate IPv6 ACL 2001. The operation is not supported.

Explanation

ACL acceleration failed because the system does not support ACL acceleration.

Recommended action

No action is required.

 

ACL_ACCELERATE_NOT_SUPPORTHOPBYHOP

Message text

Failed to accelerate IPv6 ACL [UINT32]. ACL acceleration does not support the rules that contain the hop-by-hop keywords.

Variable fields

$1: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NOT_SUPPORTHOPBYHOP: Failed to accelerate IPv6 ACL 2001. ACL acceleration does not support the rules that contain the hop-by-hop keywords.

Explanation

ACL acceleration failed for the IPv6 ACL because rules containing the hop-by-hop keyword exist in the ACL.

Recommended action

Check the ACL rules and delete the unsupported configuration.

 

ACL_ACCELERATE_NOT_SUPPORTMULTITCPFLAG

Message text

Failed to accelerate IPv6 ACL [UINT32]. ACL acceleration does not support specifying multiple TCP flags in one rule.

Variable fields

$1: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NOT_SUPPORTMULTITCPFLAG: Failed to accelerate IPv6 ACL 2001. ACL acceleration does not support specifying multiple TCP flags in one rule.

Explanation

ACL acceleration failed for the IPv6 ACL because rules containing multiple TCP flags exist in the ACL.

Recommended action

Check the ACL rules and delete the unsupported configuration.

 

ACL_ACCELERATE_UNK_ERR

Message text

Failed to accelerate [STRING] ACL [UINT32].

Variable fields

$1: ACL type.

$2: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_UNK_ERR: Failed to accelerate IPv6 ACL 2001.

Explanation

ACL acceleration failed because of an unknown error.

Recommended action

No action is required.

 

ACL_IPV6_STATIS_INFO

Message text

IPv6 ACL [UINT32] [STRING] [UINT64] packet(s).

Variable fields

$1: ACL number.

$2: ID and content of an IPv6 ACL rule.

$3: Number of packets that matched the rule.

Severity level

6

Example

ACL/6/ACL_IPV6_STATIS_INFO: IPv6 ACL 2000 rule 0 permit source 1:1::/64 logging 1000 packet(s).

Explanation

The number of packets matching the IPv6 ACL rule changed.

Recommended action

No action is required.

 

ACL_NO_MEM

Message text

Failed to configure [STRING] ACL [UINT] due to lack of memory.

Variable fields

$1: ACL type.

$2: ACL number.

Severity level

3

Example

ACL/3/ACL_NO_MEM: Failed to configure ACL 2001 due to lack of memory.

Explanation

Configuring the ACL failed because memory is insufficient.

Recommended action

Use the display memory-threshold command to check the memory usage.

 

ACL_STATIS_INFO

Message text

ACL [UINT32] [STRING] [UINT64] packet(s).

Variable fields

$1: ACL number.

$2: ID and content of an IPv4 ACL rule.

$3: Number of packets that matched the rule.

Severity level

6

Example

ACL/6/ACL_STATIS_INFO: ACL 2000 rule 0 permit source 1.1.1.1 0 logging 10000 packet(s).

Explanation

The number of packets matching the IPv4 ACL rule changed.

Recommended action

No action is required.

 

 


ANCP messages

This section contains ANCP messages.

ANCP_INVALID_PACKET

Message text

-NeighborName=[STRING]-State=[STRING]-MessageType=[STRING]; The [STRING] value [STRING] is wrong, and the value [STRING] is expected.

Variable fields

$1: ANCP neighbor name.

$2: Neighbor state.

$3: Message type.

$4: Field.

$5: Wrong value of the field.

$6: Expected value of the field.

Severity level

6

Example

ANCP/6/ANCP_INVALID_PACKET: -NeighborName=Dslam-State=SYNSENT-MessageType=SYNACK; The Sender Instance value 0 is wrong, and the value 1 is expected.

Explanation

The system received an adjacency message that had a field with a wrong value.

Recommended action

No action is required.

 

 


APMGR messages

This section contains access point management messages.

APMGR_AC_MEM_ALERT

Message text

The memory utilization has reached the threshold.

Variable fields

N/A

Severity level

4

Example

APMGR/4/APMGR_AC_MEM_ALERT: The memory utilization has reached the threshold.

Explanation

The AP failed to come online because the memory utilization exceeded the limit.

Recommended action

Stop creating manual APs and prevent APs from coming online.

 

APMGR_ADD_AP_FAIL

Message text

AP [STRING] failed to come online using serial ID [STRING]: MAC address [STRING] is being used by AP [STRING].

Variable fields

$1: AP name.

$2: Serial ID.

$3: MAC address.

$4: AP name.

Severity level

4

Example

APMGR/4/ APMGR_ADD_AP_FAIL: AP ap1 failed to come online using serial ID 01247ef96: MAC address 0023-7961-5201 is being used by AP ap2.

Explanation

The AP failed to come online because a manual AP that has the same MAC address already exists on the AC.

Recommended action

Delete either the manual AP that has the MAC address or the serial ID.

 

APMGR_ADDBAC_INFO

Message text

Add BAS AC [STRING].

Variable fields

$1: MAC address of the BAS AC.

Severity level

6

Example

APMGR/6/APMGR_ADDBAC_INFO: Add BAS AC 3ce5-a616-28cd.

Explanation

The BAS AC was connected to the master AC.

Recommended action

No action is required.

 

APMGR_AP_OFFLINE

Message text

AP [STRING] went offline. State changed to Idle.

Variable fields

$1: AP name.

Severity level

6

Example

APMGR/6/APMGR_AP_OFFLINE: AP ap1 went offline. State changed to Idle.

Explanation

The AP went offline. The state of the AP changed to Idle.

Recommended action

If the AP went offline abnormally, check the debugging information to locate the issue and resolve it.

 

APMGR_AP_ONLINE

Message text

AP [STRING] went online. State changed to Run.

Variable fields

$1: AP name.

Severity level

6

Example

APMGR/6/APMGR_AP_ONLINE: AP ap1 went online. State changed to Run.

Explanation

The AP came online. The state of the AP changed to Run.

Recommended action

No action is required.

 

APMGR_CWC_IMG_DOWNLOAD_COMPLETE

Message text

System software image file [STRING] downloading through the CAPWAP tunnel to AC [STRING] completed.

Variable fields

$1: Image file name.

$2: AC IP address.

Severity level

6

Example

APMGR/6/APMGR_CWC_IMG_DOWNLOAD_COMPLETE: System software image file 5800.ipe downloading through the CAPWAP tunnel to AC 192.168.10.1 completed.

Explanation

The AP downloaded the image file from the AC successfully.

Recommended action

No action is required.

 

APMGR_CWC_IMG_DOWNLOAD_START

Message text

Started to download the system software image file [STRING] through the CAPWAP tunnel to AC [STRING].

Variable fields

$1: Image file name.

$2: AC IP address.

Severity level

6

Example

APMGR/6/APMGR_CWC_IMG_DOWNLOAD_START: Started to download the system software image file 5800.ipe through the CAPWAP tunnel to AC 192.168.10.1.

Explanation

The AP started to download the image file from the AC.

Recommended action

Make sure the AP is correctly connected to the AC.

 

APMGR_CWC_IMG_NO_ENOUGH_SPACE

Message text

Insufficient flash memory space for downloading system software image file [STRING].

Variable fields

$1: Image file name.

Severity level

6

Example

APMGR/6/APMGR_CWC_IMG_NO_ENOUGH_SPACE: Insufficient flash memory space for downloading system software image file 5800.ipe.

Explanation

The AP failed to download the image file from the AC because of insufficient flash memory.

Recommended action

Delete files not in use from the AP.

 

APMGR_CWC_LOCAL_AC_DOWN

Message text

CAPWAP tunnel to Central AC [STRING] went down. Reason: [STRING].

Variable fields

$1: IP address of the central AC.

$2: Reason:

·     Added local AC IP address.

·     Deleted local AC IP address.

·     Local AC interface used for CAPWAP tunnel went down.

·     Local AC config changed.

·     N/A

Severity level

4

Example

APMGR/4/APMGR_CWC_LOCAL_AC_DOWN: CAPWAP tunnel to Central AC 2.2.2.1 went down. Reason: Added local AC IP address.

Explanation

The CAPWAP tunnel between the central AC and the local AC was terminated for a specific reason.

Recommended action

To resolve the issue:

1.     Examine the network connection between the central AC and the local AC.

2.     Verify that the central AC is correctly configured.

3.     Verify that the local AC is correctly configured.

4.     If the issue persists, contact H3C Support.

 

APMGR_CWC_LOCAL_AC_UP

Message text

CAPWAP tunnel to Central AC [STRING] went up.

Variable fields

$1: IP address of the central AC.

Severity level

6

Example

APMGR/6/APMGR_CWC_LOCAL_AC_UP: CAPWAP tunnel to Central AC 2.2.2.1 went up.

Explanation

The central AC has established a CAPWAP tunnel with the local AC.

Recommended action

No action is required.

 

APMGR_CWC_REBOOT

Message text

AP in state [STRING] is rebooting. Reason: [STRING]

Variable fields

$1: AP state.

$2: Reason:

·     AP was reset.

·     Image was downloaded successfully.

·     AP stayed in idle state for a long time.

Severity level

6

Example

APMGR/6/APMGR_CWC_REBOOT: AP in State Run is rebooting. Reason: AP was reset.

Explanation

The AP rebooted for a specific reason.

Recommended action

No action is required.

 

APMGR_CWC_RUN_DOWNLOAD_COMPLETE

Message text

File [STRING] successfully downloaded through the CAPWAP tunnel to AC [STRING].

Variable fields

$1: File name.

$2: AC IP address.

Severity level

6

Example

APMGR/6/APMGR_CWC_RUN_DOWNLOAD_COMPLETE: File ac.cfg successfully downloaded through the CAPWAP tunnel to AC 192.168.10.1.

Explanation

The AP downloaded the file from the AC successfully.

Recommended action

No action is required.

 

APMGR_CWC_RUN_DOWNLOAD_START

Message text

Started to download the file [STRING] through the CAPWAP tunnel to AC [STRING].

Variable fields

$1: File name.

$2: AC IP address.

Severity level

6

Example

APMGR/6/APMGR_CWC_RUN_DOWNLOAD_START: Started to download the file ac.cfg through the CAPWAP tunnel to AC 192.168.10.1.

Explanation

The AP started to download the file from the AC.

Recommended action

Make sure the AP is correctly connected to the AC.

 

APMGR_CWC_RUN_NO_ENOUGH_SPACE

Message text

Insufficient flash memory space for downloading file [STRING].

Variable fields

$1: File name.

Severity level

6

Example

APMGR/6/APMGR_CWC_RUN_NO_ENOUGH_SPACE: Insufficient flash memory space for downloading file ac.cfg.

Explanation

The AP failed to download the file from the AC because of insufficient flash memory.

Recommended action

Delete files not in use from the AP.

 

APMGR_CWC_TUNNEL_DOWN

Message text

CAPWAP tunnel to AC [STRING] went down. Reason: [STRING].

Variable fields

$1: AC IP address.

$2: Reason:

·     Added AP IP address.

·     Deleted AP IP address.

·     AP interface used for CAPWAP tunnel went down.

·     AP config changed.

·     AP was reset.

·     Number of echo retransmission attempts exceeded the limit.

·     Full retransmission queue.

·     Data channel timer expired.

·     Backup AC IP address changed.

·     Backup tunnel changed to master tunnel.

·     Failed to change backup tunnel to master tunnel.

·     Backup method changed.

·     N/A.

Severity level

6

Example

APMGR/6/APMGR_CWC_TUNNEL_DOWN: CAPWAP tunnel to AC 192.168.10.1 went down. Reason: AP was reset.

Explanation

The CAPWAP tunnel between the AP and the AC was terminated for a specific reason.

Recommended action

Examine the network connection between the AP and the AC.

 

APMGR_CWC_TUNNEL_UP

Message text

[STRING] CAPWAP tunnel to AC [STRING] went up.

Variable fields

$1: Tunnel type:

·     Master.

·     Backup.

$2: AC IP address.

Severity level

6

Example

APMGR/6/APMGR_CWC_TUNNEL_UP: Master CAPWAP tunnel to AC 192.168.10.1 went up.

Explanation

The AP was connected to the AC successfully and entered Run state.

Recommended action

No action is required.

 

APMGR_CWS_IMG_DOWNLOAD_COMPLETE

Message text

System software image file [STRING] downloading through the CAPWAP tunnel for AP [STRING] completed.

Variable fields

$1: Image file name.

$2: AP name.

Severity level

6

Example

APMGR/6/APMGR_ CWS_IMG_DOWNLOAD_COMPLETE: System software image file 5800.ipe downloading through the CAPWAP tunnel for AP ap2 completed.

Explanation

The AP downloaded the image file from the AC successfully.

Recommended action

No action is required.

 

APMGR_CWS_IMG_DOWNLOAD_START

Message text

AP [STRING] started to download the system software image file [STRING].

Variable fields

$1: AP name.

$2: Image file name.

Severity level

6

Example

APMGR/6/APMGR_CWS_IMG_DOWNLOAD_START: AP ap1 started to download the system software image file 5800.ipe.

Explanation

The AP started to download the image file from the AC.

Recommended action

No action is required.

 

APMGR_CWS_LOCAL_AC_DOWN

Message text

CAPWAP tunnel to local AC [STRING] went down. Reason: [STRING].

Variable fields

$1: IP address of the local AC.

$2: Reason:

·     Neighbor dead timer expired.

·     Local AC was deleted.

·     Serial number changed.

·     Processed join request in Run state.

·     Failed to retransmit message.

·     N/A

Severity level

4

Example

APMGR/4/APMGR_CWS_LOCAL_AC_DOWN: CAPWAP tunnel to local AC 1.1.1.1 went down. Reason: Serial number changed.

Explanation

The CAPWAP tunnel between the central AC and the local AC was terminated for a specific reason.

Recommended action

To resolve the issue:

1.     Examine the network connection between the central AC and the local AC.

2.     Verify that the central AC is correctly configured.

3.     Verify that the local AC is correctly configured.

4.     If the issue persists, contact H3C Support.

 

APMGR_CWS_LOCAL_AC_UP

Message text

CAPWAP tunnel to local AC [STRING] went up.

Variable fields

$1: IP address of the local AC.

Severity level

6

Example

APMGR/6/APMGR_CWS_LOCAL_AC_UP: CAPWAP tunnel to local AC 1.1.1.1 went up.

Explanation

The central AC has established a CAPWAP tunnel with the local AC.

Recommended action

No action is required.

 

APMGR_CWS_RUN_DOWNLOAD_COMPLETE

Message text

File [STRING] successfully downloaded through the CAPWAP tunnel for AP [STRING].

Variable fields

$1: File name.

$2: AP name.

Severity level

6

Example

APMGR/6/APMGR_CWS_RUN_DOWNLOAD_COMPLETE: File ac.cfg successfully downloaded through the CAPWAP tunnel for AP ap2.

Explanation

The AP downloaded the file from the AC successfully.

Recommended action

No action is required.

 

APMGR_CWS_RUN_DOWNLOAD_START

Message text

AP [STRING] started to download the file [STRING].

Variable fields

$1: AP name.

$2: File name.

Severity level

6

Example

APMGR/6/APMGR_CWS_RUN_DOWNLOAD_START: AP ap1 started to download the file ac.cfg.

Explanation

The AP started to download the file from the AC.

Recommended action

No action is required.

 

APMGR_CWS_TUNNEL_DOWN

Message text

CAPWAP tunnel to AP [STRING] went down. Reason: [STRING].

Variable fields

$1: AP name.

$2: Reason:

·     Neighbor dead timer expired.

·     AP was reset.

·     AP was deleted.

·     Serial number changed.

·     Processed join request in Run state.

·     Failed to retransmit message.

·     Received WTP tunnel down event from AP.

·     Backup AC closed the backup tunnel.

·     Tunnel switched.

·     N/A.

Severity level

6

Example

APMGR/6/APMGR_CWS_TUNNEL_DOWN: CAPWAP tunnel to AP ap1 went down. Reason: AP was reset.

Explanation

The AP went offline for a specific reason.

Recommended action

To resolve the issue:

1.     Examine the network connection between the AP and the AC.

2.     Verify that the AP is correctly configured.

3.     Verify that the AC is correctly configured.

4.     If the issue persists, contact H3C Support.

 

APMGR_CWS_TUNNEL_UP

Message text

[STRING] CAPWAP tunnel to AP [STRING] went up.

Variable fields

$1: Tunnel type:

·     Master.

·     Backup.

$2: AP name.

Severity level

6

Example

APMGR/6/APMGR_CWS_TUNNEL_UP: Backup CAPWAP tunnel to AP ap1 went up.

Explanation

The AP came online and entered Run state.

Recommended action

No action is required.

 

APMGR_DELBAC_INFO

Message text

Delete BAS AC [STRING].

Variable fields

$1: MAC address of the BAS AC.

Severity level

6

Example

APMGR/6/APMGR_DELBAC_INFO: Delete BAS AC 3ce5-a616-28cd.

Explanation

The BAS AC was disconnected from the master AC.

Recommended action

No action is required.

 

APMGR_LOCAL_AC_OFFLINE

Message text

Local AC [STRING] went offline. State changed to Idle.

Variable fields

$1: Name of the local AC.

Severity level

6

Example

APMGR/6/APMGR_LOCAL_AC_OFFLINE: Local AC ac1 went offline. State changed to Idle.

Explanation

The local AC went offline. The state of the local AC changed to Idle.

Recommended action

1.     If the local AC went offline abnormally, check the debugging information to locate the issue and resolve it.

2.     If the issue persists, contact H3C Support.

 

APMGR_LOCAL_AC_ONLINE

Message text

Local AC [STRING] went online. State changed to Run.

Variable fields

$1: Name of the local AC.

Severity level

6

Example

APMGR/6/APMGR_LOCAL_AC_ONLINE: Local AC ac1 went online. State changed to Run.

Explanation

The local AC came online. The state of the local AC changed to Run.

Recommended action

No action is required.

 

 

 


ARP messages

This section contains ARP messages.

ARP_ACTIVE_ACK_NO_REPLY

Message text

No ARP reply from IP [STRING] was received on interface [STRING].

Variable fields

$1: IP address.

$2: Interface name.

Severity level

6

Example

ARP/6/ARP_ACTIVE_ACK_NO_REPLY: No ARP reply from IP 192.168.10.1 was received on interface GigabitEthernet1/0/1.

Explanation

The ARP active acknowledgement feature did not receive an ARP reply after it sent an ARP request to the sender IP of an ARP message.

This message indicates the risk of attacks.

Recommended action

1.     Verify that the learned ARP entries on the device are consistent with the existing legal devices. When gateways and servers are on the network, check the ARP entries for these devices first.

2.     If the ARP entries are correct and the attack continues, contact H3C Support.

 

ARP_ACTIVE_ACK_NOREQUESTED_REPLY

Message text

Interface [STRING] received from IP [STRING] an ARP reply that was not requested by the device.

Variable fields

$1: Interface name.

$2: IP address.

Severity level

6

Example

ARP/6/ARP_ACTIVE_ACK_NOREQUESTED_REPLY: Interface GigabitEthernet1/0/1 received from IP 192.168.10.1 an ARP reply that was not requested by the device.

Explanation

The ARP active acknowledgement feature received an unsolicited ARP reply from a sender IP.

This message indicates the risk of attacks.

Recommended action

No action is required. The device discards the ARP reply automatically.

 

ARP_BINDRULETOHW_FAILED

Message text

Failed to download binding rule to hardware on the interface [STRING], SrcIP [IPADDR], SrcMAC [MAC], VLAN [UINT16], Gateway MAC [MAC].

Variable fields

$1: Interface name.

$2: Source IP address.

$3: Source MAC address.

$4: VLAN ID.

$5: Gateway MAC address.

Severity level

5

Example

ARP/5/ARP_BINDRULETOHW_FAILED: Failed to download binding rule to hardware on the interface GigabitEthernet1/0/1, SrcIP 1.1.1.132, SrcMAC 0015-E944-A947, VLAN 1, Gateway MAC 00A1-B812-1108.

Explanation

The system failed to set a binding rule to the hardware on an interface. The message is sent in any of the following situations:

·     The resources are not sufficient for the operation.

·     The memory is not sufficient for the operation.

·     A hardware error occurs.

Recommended action

To resolve the problem:

1.     Execute the display qos-acl resource command to check if the ACL resources for the operation are sufficient.

¡     If yes, proceed to step 2.

¡     If no, delete unnecessary configuration to release ACL resources. If no configuration can be deleted, proceed to step 2.

2.     Execute the display memory command to check if the memory for the operation is sufficient.

¡     If yes, proceed to step 3.

¡     If no, delete unnecessary configuration to release memory. If no configuration can be deleted, proceed to step 3.

3.     Delete the configuration and perform the operation again.

 

ARP_DETECTION_LOG

Message text

Detected an ARP attack on interface [STRING]: IP [STRING], MAC [STRING], VLAN [STRING]. [UINT32] packet(s) dropped.

Variable fields

$1: Interface name.

$2: IP address.

$3: MAC address.

$4: VLAN ID.

$5: Number of dropped packets.

Severity level

5

Example

ARP/5/ARP_INSPECTION: -MDC=1; Detected an ARP attack on interface GigabitEthernet1/0/1: IP 1.1.1.1, MAC 1-1-1, VLAN 100. 2 packet(s) dropped.

Explanation

An ARP attack was detected on an interface and attack packets were dropped.

Recommended action

Check the source of the ARP attack.

 

ARP_DUPLICATE_IPADDR_DETECT

Message text

Detected an IP address conflict. The device with MAC address [STRING] connected to interface [STRING] in VSI [STRING] and the device with MAC address [STRING] connected to interface [STRING] in VSI [STRING] were using the same IP address [IPADDR].

Variable fields

$1: MAC address.

$2: Interface name. (The interface can be a tunnel interface, Layer 3 interface, or Ethernet service instance.)

$3: VSI name.

$4: MAC address.

$5: Interface name. (The interface can be a tunnel interface, Layer 3 interface, or Ethernet service instance.)

$6: VSI name.

$7: Conflicting IP address.

Severity level

4

Example

ARP/4/ARP_DUPLICATE_IPADDR_DETECT: Detected an IP address conflict. The device with MAC address 00-00-01 connected to interface GigabitEthernet1/0/1 service-instance 1000 in VSI vpna and the device with MAC address 00-00-02 connected to interface tunnel 10 in VSI vpna were using the same IP address 192.168.1.1.

Explanation

This message is sent when an interface receives an ARP message in which the sender information conflicts with an existing ARP entry. The sender IP address is the same as the IP address in the entry, but the MAC addresses are different.

Recommended action

Change the IP address on either of the two devices.

 

ARP_DYNAMIC

Message text

The maximum number of dynamic ARP entries for the device reached.

Variable fields

N/A

Severity level

6

Example

ARP/6/ARP_DYNAMIC: The maximum number of dynamic ARP entries for the device reached.

Explanation

The maximum number of dynamic ARP entries for the device was reached.

Recommended action

No action is required.

 

ARP_DYNAMIC_IF

Message text

The maximum number of dynamic ARP entries for interface [STRING] reached.

Variable fields

$1: Interface name.

Severity level

6

Example

ARP/6/ARP_DYNAMIC_IF: The maximum number of dynamic ARP entries for interface GigabitEthernet1/0/1 reached.

Explanation

The maximum number of dynamic ARP entries for the specified interface was reached.

Recommended action

No action is required.

 

ARP_DYNAMIC_SLOT

Message text

Pattern 1:

The maximum number of dynamic ARP entries for slot [INT32] reached.

Pattern 2:

The maximum number of dynamic ARP entries for chassis [INT32] slot [INT32] reached.

Variable fields

Pattern 1:

$1: Slot number.

Pattern 2:

$1: Chassis number.

$2: Slot number.

Severity level

6

Example

ARP/6/ARP_DYNAMIC_SLOT: The maximum number of dynamic ARP entries for slot 2 reached.

Explanation

Pattern 1:

The maximum number of dynamic ARP entries for the slot was reached.

Pattern 2:

The maximum number of dynamic ARP entries for the slot on the chassis was reached.

Recommended action

No action is required.

 

ARP_ENTRY_CONFLICT

Message text

The software entry for [STRING] on [STRING] and the hardware entry did not have the same [STRING].

Variable fields

$1: IP address.

$2: VPN instance name. If the ARP entry belongs to the public network, this field displays the public network.

$3: Inconsistent items:

¡     MAC address.

¡     output interface.

¡     output port.

¡     outermost layer VLAN ID.

¡     second outermost layer VLAN ID.

¡     VSI index.

¡     link ID.

Severity level

6

Example

ARP/6/ARP_ENTRY_CONFLICT: The software entry for 1.1.1.1 on the VPN a and the hardware entry did not have the same MAC address, output port, VSI index, and link ID.

ARP/6/ARP_ENTRY_CONFLICT: The software entry for 1.1.1.2 on the public network and the hardware entry did not have the same MAC address, output port, VSI index, and link ID.

Explanation

The software entry for the specified IP address is not the same as the hardware entry. For example, they do not have the same output interface.

Recommended action

No action is required. ARP automatically refreshes the hardware entries.

 

ARP_HOST_IP_CONFLICT

Message text

The host [STRING] connected to interface [STRING] cannot communicate correctly, because it uses the same IP address as the host connected to interface [STRING].

Variable fields

$1: IP address.

$2: Interface name.

$3: Interface name.

Severity level

4

Example

ARP/4/ARP_HOST_IP_CONFLICT: The host 1.1.1.1 connected to interface GigabitEthernet1/0/1 cannot communicate correctly, because it uses the same IP address as the host connected to interface GigabitEthernet1/0/2.

Explanation

The sender IP address in a received ARP message conflicted with the IP address of a host connected to another interface.

Recommended action

Check whether the hosts that send the ARP messages are legitimate. Disconnect the illegal host from the network.

 

ARP_LOCALPROXY_ENABLE_FAILED

Message text

Failed to enable local proxy ARP on interface [STRING].

Variable fields

$1: Interface name.

Severity level

4

Example

ARP/4/ARP_LOCALPROXY_ENABLE_FAILED: -MDC=1-Slot=2; Failed to enable local proxy ARP on interface VSI-interface 1.

Explanation

This message is sent when the device fails to enable local proxy ARP on an interface in a slot. If the interface resides on the MPU, the slot number is 0.

Recommended action

1.     Verify that the card supports local proxy ARP.

2.     Verify that sufficient hardware resources are available.

 

ARP_RATE_EXCEEDED

Message text

The ARP packet rate ([UINT32] pps) exceeded the rate limit ([UINT32] pps) on interface [STRING] in the last [UINT32] seconds.

Variable fields

$1: ARP packet rate.

$2: ARP limit rate.

$3: Interface name.

$4: Interval time.

Severity level

4

Example

ARP/4/ARP_RATE_EXCEEDED: The ARP packet rate (100 pps) exceeded the rate limit (80 pps) on interface GigabitEthernet1/0/1 in the last 10 seconds.

Explanation

An interface received ARP messages at a higher rate than the rate limit.

Recommended action

Verify that the hosts at the sender IP addresses are legitimate.

 

ARP_RATELIMIT_NOTSUPPORT

Message text

Pattern 1:

ARP packet rate limit is not support on slot [INT32].

Pattern 2:

ARP packet rate limit is not support on chassis [INT32] slot [INT32].

Variable fields

Pattern 1:

$1: Slot number.

Pattern 2:

$1: Chassis number.

$2: Slot number.

Severity level

6

Example

ARP/6/ARP_RATELIMIT_NOTSUPPORT: ARP packet rate limit is not support on slot 2.

Explanation

Pattern 1:

ARP packet rate limit is not supported on the slot.

Pattern 2:

ARP packet rate limit is not supported on the slot of the chassis was reached.

Recommended action

Verify that the host at the sender IP address is legitimate.

 

ARP_SENDER_IP_INVALID

Message text

Sender IP [STRING] was not on the same network as the receiving interface [STRING].

Variable fields

$1: IP address.

$2: Interface name.

Severity level

6

Example

ARP/6/ARP_SENDER_IP_INVALID: Sender IP 192.168.10.2 was not on the same network as the receiving interface GigabitEthernet1/0/1.

Explanation

The sender IP of a received ARP message was not on the same network as the receiving interface.

Recommended action

Verify that the host at the sender IP address is legitimate.

 

ARP_SENDER_MAC_INVALID

Message text

Sender MAC [STRING] was not identical to Ethernet source MAC [STRING] on interface [STRING].

Variable fields

$1: MAC address.

$2: MAC address.

$3: Interface name.

Severity level

6

Example

ARP/6/ARP_SENDER_MAC_INVALID: Sender MAC 0000-5E14-0E00 was not identical to Ethernet source MAC 0000-5C14-0E00 on interface GigabitEthernet1/0/1.

Explanation

An interface received an ARP message. The sender MAC address in the message body was not identical to the source MAC address in the Ethernet header.

Recommended action

Verify that the host at the sender MAC address is legitimate.

 

ARP_SENDER_SMACCONFLICT

Message text

Packet was discarded because its sender MAC address was the MAC address of the receiving interface.

Interface: [STRING], sender IP: [STRING], target IP: [STRING].

Variable fields

$1: Interface name.

$2: Sender IP address.

$3: Target IP address.

Severity level

6

Example

ARP/6/ ARP_SENDER_SMACCONFLICT: Packet discarded for the sender MAC address is the same as the receiving interface.

Interface: GigabitEthernet1/0/1 sender IP: 1.1.2.2 target IP: 1.1.2.1,

Explanation

The sender MAC address of a received ARP packet conflicts with the MAC address of the device.

Recommended action

No action is required.

 

ARP_SENDER_SMACCONFLICT_VSI

Message text

Packet was discarded because its sender MAC address was the MAC address of the receiving interface.

Interface: [STRING], sender IP: [STRING], target IP: [STRING],VSI index: [UINT32], link ID: [UINT32].

Variable fields

$1: Interface name.

$2: Sender IP address.

$3: Target IP address.

$4: VSI index.

$5: Link ID.

Severity level

6

Example

ARP/6/ ARP_SENDER_SMACCONFLICT_VSI: Packet discarded for the sender MAC address is the same as the receiving interface.

Interface: VSI3 sender IP: 1.1.2.2 target IP: 1.1.2.1, VSI Index: 2, Link ID: 0

Explanation

The sender MAC address of a received ARP packet conflicts with the MAC address of the device. The receiving interface is a VSI interface.

Recommended action

No action is required.

 

ARP_SRC_MAC_FOUND_ATTACK

Message text

An attack from MAC [STRING] was detected on interface [STRING].

Variable fields

$1: MAC address.

$2: Interface name.

Severity level

6

Example

ARP/6/ARP_SRC_MAC_FOUND_ATTACK: An attack from MAC 0000-5E14-0E00 was detected on interface GigabitEthernet1/0/1.

Explanation

The source MAC-based ARP attack detection feature received more ARP packets from the same MAC address within 5 seconds than the specified threshold.

This message indicates the risk of attacks.

Recommended action

Verify that the host at the source MAC address is legitimate.

 

ARP_SUP_ENABLE_FAILED

Message text

Failed to enable ARP flood suppression on VSI [STRING].

Variable fields

$1: VSI name.

Severity level

4

Example

ARP/4/ARP_SUP_ENABLE_FAILED: -MDC=1; Failed to enable ARP flood suppression on VSI vpna.

Explanation

This message is sent when the system failed to enable ARP flood suppression for a VSI. The minimum interval between two log messages is 2 seconds. To make the system send the message successfully, wait for a minimum of 2 seconds before you enable ARP flood suppression for another VSI.

Recommended action

1.     Verify that the device supports ARP flood suppression.

2.     Verify that the hardware resources are sufficient.

 

ARP_TARGET_IP_INVALID

Message text

Target IP [STRING] was not the IP of the receiving interface [STRING].

Variable fields

$1: IP address.

$2: Interface name.

Severity level

6

Example

ARP/6/ARP_TARGET_IP_INVALID: Target IP 192.168.10.2 was not the IP of the receiving interface GigabitEthernet1/0/1.

Explanation

The target IP address of a received ARP message was not the IP address of the receiving interface.

Recommended action

Verify that the host at the sender IP address is legitimate.

 

ARP_THRESHOLD_REACHED

Message text

The alarm threshold for dynamic ARP entry learning was reached on interface [STRING].

Variable fields

$1: Interface name.

Severity level

4

Example

ARP/4/ARP_THRESHOLD_REACHED: The alarm threshold for dynamic ARP entry learning was reached on interface GigabitEthernet1/0/1.

Explanation

This message is sent when the alarm threshold for dynamic ARP learning was reached on GigabitEthernet 1/0/1.

Recommended action

Verify that the number of learned dynamic ARP entries matches the actual number of devices in the network and no ARP attack sources exist in the network.

 

ARP_USER_DUPLICATE_IPADDR_DETECT

Message text

Detected a user IP address conflict. New user (MAC [STRING], SVLAN [STRING], CVLAN [STRING]) connecting on interface [STRING] and old user (MAC [STRING], SVLAN [STRING], CVLAN [STRING]) connecting on interface [STRING] were using the same IP address [IPADDR].

Variable fields

$1: MAC address of a new user.

$2: Outer VLAN to which the new user belongs.

$3: Inner VLAN to which the new user belongs.

$4: Name of the interface connecting to the new user.

$5: MAC address of an old user.

$6: Outer VLAN to which the old user belongs.

$7: Inner VLAN to which the old user belongs.

$8: Name of the interface connecting to the old user.

$9: IP address.

Severity level

6

Example

ARP/6/ARP_USER_DUPLICATE_IPADDR_DETECT: Detected a user IP address conflict. New user (MAC 0010-2100-01e1, SVLAN 100, CVLAN 10) connecting on interface GigabitEthernet1/0/1 and old user (MAC 0120-1e00-0102, SVLAN 100, CVLAN 10) connecting on interface GigabitEthernet1/0/1 were using the same IP address 192.168.1.1.

Explanation

ARP detected a user IP address conflict. The IP address of a new user is the same as the IP address of an old user.

Recommended action

Verify that all users have different IP addresses.

 

ARP_USER_MOVE_DETECT

Message text

Detected a user (IP address [IPADDR], MAC address [STRING]) moved to another interface. Before user move: interface [STRING], SVLAN [STRING], CVLAN [STRING]. After user move: interface [STRING], SVLAN [STRING], CVLAN [STRING].

Variable fields

$1: IP address of the user.

$2: MAC address of the user.

$3: Interface name before the migration.

$4: Outer VLAN to which the user belongs before the migration.

$5: Inner VLAN to which the user belongs before the migration.

$6: Interface name after the migration.

$7: Outer VLAN to which the user belongs after the migration.

$8: Inner VLAN to which the user belongs after the migration.

Severity level

6

Example

ARP/6/ARP_USER_MOVE_DETECT: Detected a user (IP address 192.168.1.1, MAC address 0010-2100-01e1) moved to another interface. Before user move: interface GigabitEthernet1/0/1, SVLAN 100, CVLAN 10. After user move: interface GigabitEthernet1/0/2, SVLAN 100, CVLAN 10.

Explanation

ARP detected a user accesses the network through another port.

Recommended action

Use the display arp user-move record command to verify that the migration is legitimate.

 

DUPIFIP

Message text

Duplicate address [STRING] on interface [STRING], sourced from [STRING].

Variable fields

$1: IP address.

$2: Interface name.

$3: MAC Address.

Severity level

6

Example

ARP/6/DUPIFIP: Duplicate address 1.1.1.1 on interface GigabitEthernet1/0/1, sourced from 0015-E944-A947.

Explanation

ARP detected a duplicate address.

The sender IP in the received ARP packet was being used by the receiving interface.

Recommended action

Modify the IP address configuration.

 

DUPIP

Message text

IP address [STRING] conflicted with global or imported IP address, sourced from [STRING].

Variable fields

$1: IP address.

$2: MAC Address.

Severity level

6

Example

ARP/6/DUPIP: IP address 30.1.1.1 conflicted with global or imported IP address, sourced from 0000-0000-0001.

Explanation

The sender IP address of the received ARP packet conflicted with the global or imported IP address.

Recommended action

Modify the IP address configuration.

 

DUPVRRPIP

Message text

IP address [STRING] conflicted with VRRP virtual IP address on interface [STRING], sourced from [STRING].

Variable fields

$1: IP address.

$2: Interface name.

$3: MAC address.

Severity level

6

Example

ARP/6/DUPVRRPIP: IP address 1.1.1.1 conflicted with VRRP virtual IP address on interface GigabitEthernet1/0/1, sourced from 0015-E944-A947.

Explanation

The sender IP address of the received ARP packet conflicted with the VRRP virtual IP address.

Recommended action

Modify the IP address configuration.

 

 


ATK messages

This section contains attack detection and prevention messages.

ATK_ICMP_ADDRMASK_REQ

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_REQ: IcmpType(1058)=17; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP address mask request logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_ADDRMASK_REQ_RAW

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_REQ_RAW: IcmpType(1058)=17; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP address mask requests of the same attributes, this message is sent only when the first request is received.

If log aggregation is disabled, this message is sent every time an ICMP address mask request is received.

Recommended action

No action is required.

 

ATK_ICMP_ADDRMASK_REQ_RAW_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_REQ_RAW_SZ: IcmpType(1058)=17; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP address mask requests of the same attributes, this message is sent only when the first request is received.

If log aggregation is disabled, this message is sent every time an ICMP address mask request is received.

Recommended action

No action is required.

 

ATK_ICMP_ADDRMASK_REQ_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_REQ_SZ: IcmpType(1058)=17; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP address mask request logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_ADDRMASK_RPL

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_RPL: IcmpType(1058)=18; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP address mask reply logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_ADDRMASK_RPL_RAW

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_RPL_RAW: IcmpType(1058)=18; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP address mask replies of the same attributes, this message is sent only when the first reply is received.

If log aggregation is disabled, this message is sent every time an ICMP address mask reply is received.

Recommended action

No action is required.

 

ATK_ICMP_ADDRMASK_RPL_RAW_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_RPL_RAW_SZ: IcmpType(1058)=18; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP address mask replies of the same attributes, this message is sent only when the first reply is received.

If log aggregation is disabled, this message is sent every time an ICMP address mask reply is received.

Recommended action

No action is required.

 

ATK_ICMP_ADDRMASK_RPL_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_RPL_SZ: IcmpType(1058)=18; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP address mask reply logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_ECHO_REQ

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_ECHO_REQ: IcmpType(1058)=8; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP echo request logs are aggregated.

Recommen