aggregate ipv6-address prefix-length [ as-set | attribute-policy route-policy-name | detail-suppressed | origin-policy route-policy-name | suppress-policy route-policy-name ] *

undo aggregate ipv6-address prefix-length

View

IPv6 address family view

Default level

2 System level

Parameters

ipv6-address: Summary address.

prefix-length: Length of summary route mask, in the range 0 to 128.

as-set: Creates a summary with AS set.

attribute-policy route-policy-name: Sets the attributes of the summary route according to the routing policy. The routing policy name is a string of 1 to 63 characters.

detail-suppressed: Only advertises the summary route.

suppress-policy route-policy-name: Suppresses specific routes defined in the routing policy. The routing policy name is a string of 1 to 63 characters.

origin-policy route-policy-name: References the routing policy to specify routes for summarization. The routing policy name is a string of 1 to 63 characters.

Table 1 Functions of the keywords

Keywords	Function
as-set	Used to create a summary route, whose AS path contains the AS path information of summarized routes. Use this keyword carefully when many AS paths need to be summarized, because the frequent changes of these specific routes may lead to route oscillation.
detail-suppressed	This keyword does not suppress the summary route, but it suppresses the advertisement of all the more specific routes. To summarize only some specific routes, use the peer filter-policy command.
suppress-policy	Used to create a summary route and suppress the advertisement of some summarized routes. If you want to suppress some routes selectively and leave other routes still advertised, use the if-match clause of the route-policy command.
origin-policy	Selects only routes satisfying the routing policy for route summarization.
attribute-policy	Sets attributes except the AS-PATH attribute for the summary route. The same work can be done by using the peer route-policy command.

Description

Use the aggregate command to create an IPv6 summary route in the IPv6 BGP routing table.

Use the undo aggregate command to remove an IPv6 summary route.

By default, no summary route is configured.

Examples

# In IPv6 address family view, create a summary of 12::/64 in the IPv6 routing table.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] aggregate 12:: 64

balance (IPv6 address family view/IPv6 BGP-VPN instance view)

Syntax

balance number

undo balance

View

IPv6 address family view, IPv6 BGP-VPN instance view

Default level

2: System level

Parameters

number: Number of BGP routes participating in load balancing, in the range of 1 to 8. When it is set to 1, load balancing is disabled.

Description

Use the balance command to configure the number of routes participating in IPv6 BGP load balancing.

Use the undo balance command to restore the default.

The feature is not available by default.

Unlike IGP, BGP has no explicit metric for making load balancing decision. Instead, it implements load balancing by defining its routing rule.

Related commands: display bgp ipv6 routing-table.

Examples

# Set the number of routes participating in IPv6 BGP load balancing to 2.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] balance 2

bestroute as-path-neglect (IPv6 address family view)

Syntax

bestroute as-path-neglect

undo bestroute as-path-neglect

View

IPv6 address family view

Default level

2: System level

Parameters

None

Description

Use the bestroute as-path-neglect command to configure the IPv6 BGP router to not evaluate the AS_PATH during best route selection.

Use the undo bestroute as-path-neglect command to configure the IPv6 BGP router to use the AS_PATH during best route selection.

By default, the router takes AS_PATH as a factor when selecting the best route.

Examples

# Ignore AS_PATH in route selection.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] bestroute as-path-neglect

bestroute compare-med (IPv6 address family view)

Syntax

bestroute compare-med

undo bestroute compare-med

View

IPv6 address family view

Default level

2: System level

Parameters

None

Description

Use the bestroute compare-med command to enable the comparison of the MED for paths from each AS.

Use the undo bestroute compare-med command to disable this comparison.

This comparison is not enabled by default.

NOTE:

After the bestroute compare-med command is executed, the balance command does not take effect.

Examples

# Compare the MED for paths from an AS for selecting the best route.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] bestroute compare-med

bestroute med-confederation (IPv6 address family view)

Syntax

bestroute med-confederation

undo bestroute med-confederation

View

IPv6 address family view

Default level

2: System level

Parameters

None

Description

Use the bestroute med-confederation command to enable the comparison of the MED for paths from confederation peers for best route selection.

Use the undo bestroute med-confederation command to disable the configuration.

By default, this comparison is not enabled.

With this feature enabled, the system can only compare the MED for paths from peers within the confederation. Paths from external ASs are advertised throughout the confederation without MED comparison.

Examples

# Compare the MED for paths from peers within the confederation.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] bestroute med-confederation

compare-different-as-med (IPv6 address family view)

Syntax

compare-different-as-med

undo compare-different-as-med

View

IPv6 address family view

Default level

2: System level

Parameters

None

Description

Use the compare-different-as-med command to enable the comparison of the MED for paths from peers in different ASs.

Use the undo compare-different-as-med command to disable the comparison.

The comparison is disabled by default.

If several paths are available for one destination, the path with the smallest MED value is selected.

Do not use this command unless associated ASs adopt the same IGP protocol and routing selection method.

Examples

# Enable to compare the MED for paths from peers in different ASs.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] compare-different-as-med

dampening (IPv6 address family view)

Syntax

dampening [ half-life-reachable half-life-unreachable reuse suppress ceiling | route-policy route-policy-name ] *

undo dampening

View

IPv6 address family view

Default level

2: System level

Parameters

half-life-reachable: Half-life for reachable routes, in the range 1 to 45 minutes. By default, the value is 15 minutes.

half-life-unreachable: Half-life for unreachable routes, in the range 1 to 45 minutes. By default, the value is 15 minutes.

reuse: Reuse threshold value for suppressed routes, in the range 1 to 20000. Penalty value of a suppressed route decreasing under the value is reused. By default, its value is 750.

suppress: Suppression threshold from 1 to 20000, which should be bigger than the reuse value. Routes with a penalty value bigger than the threshold are suppressed. By default, it is 2000.

ceiling: Ceiling penalty value from 1001 to 20000. The value must be bigger than the suppress value. By default, the value is 16000.

route-policy-name: Routing policy name, a string of 1 to 63 characters.

half-life-reachable, half-life-unreachable, reuse, suppress and ceiling are mutually dependent. Once any one is configured, all the others should also be specified.

Description

Use the dampening command to enable IPv6 BGP route dampening, configure dampening parameters, or both.

Use the undo dampening command to disable route dampening.

By default, no route dampening is configured.

Related commands: reset bgp ipv6 dampening, reset bgp ipv6 flap-info, display bgp ipv6 routing-table dampened, display bgp ipv6 routing-table dampening parameter, and display bgp ipv6 routing-table flap-info.

Examples

# Enable IPv6 BGP route dampening and configure route dampening parameters.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] dampening 10 10 1000 2000 3000

default local-preference (IPv6 address family view/IPv6 BGP-VPN instance view)

Syntax

default local-preference value

undo default local-preference

View

IPv6 address family view, IPv6 BGP-VPN instance view

Default level

2: System level

Parameters

value: Default local preference, in the range 0 to 4294967295. The larger the value is, the higher the preference is.

Description

Use the default local-preference command to configure the default local preference.

Use the undo default local-preference command to restore the default value.

By default, the default local preference is 100.

Use this command to affect IPv6 BGP route selection.

Examples

# Two routers A and B in the same AS are connected to another AS. Change the local preference of B from default value 100 to 180, making the route passing B preferred.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] default local-preference 180

default med (IPv6 address family view/IPv6 BGP-VPN instance view)

Syntax

default med med-value

undo default med

View

IPv6 address family view, IPv6 BGP-VPN instance view

Default level

2: System level

Parameters

med-value: MED value, in the range 0 to 4294967295.

Description

Use the default med command to specify the default MED value.

Use the undo default med command to restore the default.

By default, the default med-value is 0.

The multi-exit discriminator (MED) is an external metric of a route. Different from local preference, MED is exchanged between ASs and will stay in the AS once it enters the AS. The route with a lower MED is preferred. When a router running BGP obtains several routes with the identical destination and different next-hops from various external peers, it will select the best route depending on the MED value. In the case that all other conditions are the same, the system first selects the route with the smaller MED value as the best route for the autonomous system.

Examples

# Routers A and B belong to AS100 and Router C belongs to AS200. C is the peer of A and B. Configure the MED of A as 25 to make C select the path from B.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] default med 25

default-route imported (IPv6 address family view/IPv6 BGP-VPN instance view)

Syntax

default-route imported

undo default-route imported

View

IPv6 address family view, IPv6 BGP-VPN instance view

Default level

2: System level

Parameters

None

Description

Use the default-route imported command to enable the redistribution of default route into the IPv6 BGP routing table.

Use the undo default-route imported command to disable the redistribution.

By default, the redistribution is not enabled.

Examples

# Enable the redistribution of default route from OSPFv3 into IPv6 BGP.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] default-route imported

[Sysname-bgp-af-ipv6] import-route ospfv3 1

display bgp ipv6 group

Syntax

display bgp ipv6 group [ ipv6-group-name ] [ | { begin | exclude | include } regular-expression ]

View

Any view

Default level

1: Monitor level

Parameters

ipv6-group-name: Peer group name, a string of 1 to 47 characters.

|: Filters command output by specifying a regular expression. For more information about regular expressions, see Fundamentals Configuration Guide.

begin: Displays the first line that matches the specified regular expression and all lines that follow.

include: Displays all lines that match the specified regular expression.

regular-expression: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.

Description

Use the display bgp ipv6 group command to display IPv6 peer group information.

If no ipv6-group-name is specified, information about all peer groups is displayed.

Examples

# Display the information of the IPv6 peer group aaa.

<Sysname> display bgp ipv6 group aaa

BGP peer-group is aaa

Remote AS 100

Type: internal

Maximum allowed prefix number: 4294967295

Threshold: 75%

Configured hold timer value: 180

Keepalive timer value: 60

Minimum time between advertisement runs is 15 seconds

Peer Preferred Value: 0

No routing policy is configured

Members:

Peer AS MsgRcvd MsgSent OutQ PrefRcv Up/Down State

2001::1 100 0 0 0 0 00:00:07 Idle

Table 2 Output description

Field	Description
BGP peer-group	Name of the peer group.
Remote AS	AS number of the peer group. If the peer group AS number has been specified with the peer ipv6-address as-number as-number command, the specified AS number is displayed in this field. Otherwise, a “Remote AS number not specified” prompt is displayed.
Type	Type of the peer group: · internal—IBGP peer group. · external—EBGP peer group.
Maximum allowed prefix number	Maximum allowed prefix number.
Threshold	Threshold value.
Configured hold timer value	Holdtime.
Keepalive timer value	Keepalive interval.
Minimum time between advertisement runs	Minimum interval between advertisements.
Peer Preferred Value	Preferred value of the routes from the peer.
No routing policy is configured	No routing policy is specified for the peer.
Members	Group members.
Peer	IPv6 address of the peer.
AS	AS number.
MsgRcvd	Number of messages received.
MsgSent	Number of messages sent.
OutQ	Number of messages to be sent.
PrefRcv	Number of prefixes received.
Up/Down	The lasting time of a session/the lasting time of present state (when no session is established).
State	State machine of peer.

display bgp ipv6 network

Syntax

display bgp ipv6 network [ | { begin | exclude | include } regular-expression ]

View

Any view

Default level

1: Monitor level

Parameters

|: Filters command output by specifying a regular expression. For more information about regular expressions, see Fundamentals Configuration Guide.

begin: Displays the first line that matches the specified regular expression and all lines that follow.

include: Displays all lines that match the specified regular expression.

regular-expression: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.

Description

Use the display bgp ipv6 network command to display IPv6 routes advertised with the network command.

Examples

# Display IPv6 routes advertised with the network command.

<Sysname> display bgp ipv6 network

BGP Local Router ID is 1.1.1.2.

Local AS Number is 200.

Network Prefix Route-policy Short-cut

2002:: 64

2001:: 64 Short-cut

Table 3 Output description

Field	Description
BGP Local Router ID	BGP Local Router ID.
Local AS Number	Local AS Number.
Network	Network address.
Prefix	Prefix length.
Route-policy	Routing policy. (A null value indicates no routing policy is configured.)
Short-cut	Shortcut route. (A null value indicates the route is not a shortcut route.)

display bgp ipv6 paths

Syntax

display bgp ipv6 paths [ as-regular-expression | | { begin | exclude | include } regular-expression ]

View

Any view

Default level

1: Monitor level

Parameters

as-regular-expression: AS path regular expression, a string of 1 to 80 characters.

|: Filters command output by specifying a regular expression. For more information about regular expressions, see Fundamentals Configuration Guide.

begin: Displays the first line that matches the specified regular expression and all lines that follow.

include: Displays all lines that match the specified regular expression.

regular-expression: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.

Description

Use the display bgp ipv6 paths command to display IPv6 BGP path information.

If no parameter is specified, all path information will be displayed.

Examples

# Display IPv6 BGP path information.

<Sysname> display bgp ipv6 paths

Address Hash Refcount MED Path/Origin

0x5917098 1 1 0 i

0x59171D0 9 2 0 100i

Table 4 Output description

Field	Description
Address	Route destination address in local database, in dotted hexadecimal notation.
Hash	Hash index.
Refcount	Count of routes that used the path.
MED	MED of the path.
Path	AS_PATH attribute of the path, recording the ASs it has passed, for avoiding routing loops.
Origin	Origin attribute of the route, which can take on one of the following values: · i—Indicates that the route is interior to the AS. Summary routes and routes defined using the network command are considered IGP routes. · e—Indicates that a route is learned from the exterior gateway protocol (EGP). · ?—Short for INCOMPLETE. It indicates that the origin of a route is unknown and the route is learned by other means. BGP sets Origin attribute of routes learned from other IGP protocols to INCOMPLETE.

display bgp ipv6 peer

Syntax

display bgp ipv6 peer [ group-name log-info | ipv4-address verbose | ipv6-address { log-info | verbose } | verbose ] [ | { begin | exclude | include } regular-expression ]

View

Any view

Default level

1: Monitor level

Parameters

group-name: Name of an IPv4 or IPv6 peer group, a string of 1 to 47 characters.

ipv4-address: IPv4 address of a peer.

ipv6-address: Specifies the IPv6 address of a peer to be displayed.

log-info: Displays log information of the specified peer.

verbose: Displays the detailed information of the peer.

|: Filters command output by specifying a regular expression. For more information about regular expressions, see Fundamentals Configuration Guide.

begin: Displays the first line that matches the specified regular expression and all lines that follow.

include: Displays all lines that match the specified regular expression.

regular-expression: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.

Description

Use the display bgp ipv6 peer command to display peer/peer group information.

If no parameter specified, information about all peers and peer groups is displayed.

Examples

# Display all IPv6 peer information.

<Sysname> display bgp ipv6 peer

BGP local router ID : 192.168.1.40

Local AS number : 100

Total number of peers : 1 Peers in established state : 0

Peer AS MsgRcvd MsgSent OutQ PrefRcv Up/Down State

2001::1 100 0 0 0 0 00:02:02 Active

Table 5 Output description

Field	Description
BGP local router ID	Local router ID
Local AS number	Local AS number
Total number of peers	Total number of BGP peers
Peers in established state	BGP connection state
Peer	IPv6 address of the peer
AS	AS number
MsgRcvd	Messages received
MsgSent	Messages sent
OutQ	Messages to be sent
PrefRcv	Number of prefixes received
Up/Down	The lasting time of a session/the lasting time of present state (when no session is established)
State	Peer state

# Display the detailed information of IPv6 peer 1::1.

<Sysname> display bgp ipv6 peer 1::1 verbose

BGP Peer is 1::1, remote AS 100,

Type: EBGP link

BGP version 4, remote router ID 45.1.1.1

BGP current state: Established, Up for 00h01m34s

BGP current event: KATimerExpired

BGP last state: OpenConfirm

Port: Local - 1031 Remote - 179

Configured: Active Hold Time: 180 sec Keepalive Time: 60 sec

Received : Active Hold Time: 180 sec

Negotiated: Active Hold Time: 180 sec Keepalive Time:60 sec

Peer optional capabilities:

Peer support bgp multi-protocol extended

Peer support bgp route refresh capability

Peer support bgp route AS4 capability

Graceful Restart Capability: advertised and received

Restart Timer Value of Peer: 150 seconds

Forwarding State preserved by Peer for following Address families:

Address family IPv6 Unicast: advertised and received

Received: Total 4 messages, Update messages 1

Sent: Total 6 messages, Update messages 3

Maximum allowed prefix number: 4294967295

Threshold: 75%

Minimum time between advertisement runs is 30 seconds

Optional capabilities:

Route refresh capability has been enabled

Peer Preferred Value: 0

Routing policy configured:

No routing policy is configured

BFD: Enabled

# Display the detailed information of IPv6 BGP peers.

<Sysname> display bgp ipv6 peer verbose

BGP Peer is 2::4, remote AS 1,

Type: IBGP link

BGP version 4, remote router ID 1.1.1.1

BGP current state: Established, Up for 00h01m51s

BGP current event: RecvKeepalive

BGP last state: OpenConfirm

Received: Total 5 messages, Update messages 1

Sent: Total 4 messages, Update messages 0

Maximum allowed prefix number: 4294967295

Threshold: 75%

Minimum time between advertisement runs is 30 seconds

Optional capabilities:

Route refresh capability has been enabled

ORF advertise capability based on prefix (type 64):

Local: both

Negotiated: send

Peer Preferred Value: 0

IPsec policy name: policy001, SPI: 300

Routing policy configured:

No routing policy is configured

Table 6 Output description

Field	Description
Type	BGP connection type: EBGP or IBGP.
Up for	Lasting time of a BGP connection.
Peer optional capabilities: Peer support bgp multi-protocol extended Peer support bgp route refresh capability Peer support bgp route AS4 capability	Optional capabilities supported by the BGP peer: · Multi-protocol extension for BGP. · Route-refresh feature. · 4-byte AS number.
Graceful Restart Capability: advertised and received Restart Timer Value of Peer: 150 seconds Forwarding State preserved by Peer for following Address families:	GR capability: the advertising and receiving capabilities have been successfully negotiated. · GR restart timer of the peer is 150 seconds. · Address family information for which the peer preserves the forwarding state.
Address family IPv6 Unicast: advertised and received	BGP IPv6 unicast capability: the advertising and receiving capabilities have been successfully negotiated.
Threshold	Threshold of the routes received from the peer (ratio of the number of received routes to the configured upper limit in percentage) when an alarm is generated.
Minimum time between advertisement runs is 30 seconds	Minimum interval between advertisements.
Optional capabilities Route refresh capability has been enabled ORF advertise capability based on prefix (type 64): Local: both Negotiated: send	Optional capabilities enabled on the peer: · Route-refresh is enabled. · The IPv6 BGP peer supports the ORF capability based on IP prefix. The capability value is 64. · The local IPv6 BGP router supports both the ORF sending and receiving capabilities. · Negotiation result: The local IPv6 BGP router can send Router-refresh messages carrying the ORF information, and the peer can receive Router-refresh messages carrying the ORF information. (If receive is displayed, the local BGP router can receive Router-refresh messages carrying the ORF information, and the peer can send Router-refresh messages carrying the ORF information. This field is not displayed if neither the send nor the receive capability is supported.
Peer Preferred Value	Preferred value assigned to routes received from the peer.
IPsec policy name: policy001, SPI: 300	IPsec policy applied to the peer and SPI of the IPsec policy.
BFD	Indicates whether BFD is enabled over the link to the IPv6 BGP peer.

# Display the log information of the IPv6 peer 20::21.

<sysname> display bgp ipv6 peer 20::21 log-info

Peer : 20::21

Date Time State Notification

Error/SubError

10-Jul-2008 15:46:17 Down Send Notification with Error 1/1

Message Header Error/Connection Not Synchronized

10-Jul-2008 09:23:00 Up

10-Jul-2008 07:46:17 Down Receive Notification with Error 3/2

UPDATE Message Error/Unsupported optional Parameter

10-Jul-2008 06:23:00 Up

10-Jul-2008 05:46:17 Down Send Notification with Error 6/4

Administrative Reset

Table 7 Output description

Field	Description
Peer	IPv6 address of the peer.
Date	Date on which the Notification was sent or received.
Time	Time at which the Notification was sent or received.
State	BGP session state, which can be: · Up—Indicates the BGP session is up. · Down—Indicates the BGP session is down.
Notification	Notification message.
Error/SubError	Error refers to the error code, which identifies the type of the Notification. SubError refers to the error subcode of the Notification, which identifies the specific information about the reported error.

display bgp ipv6 peer received ipv6-prefix

Syntax

display bgp ipv6 peer { ip-address | ipv6-address } received ipv6-prefix [ | { begin | exclude | include } regular-expression ]

View

Any view

Default level

1: Monitor level

Parameters

ip-address: IP address of a BGP peer.

ipv6-address: IPv6 address of a BGP peer.

|: Filters command output by specifying a regular expression. For more information about regular expressions, see Fundamentals Configuration Guide.

begin: Displays the first line that matches the specified regular expression and all lines that follow.

include: Displays all lines that match the specified regular expression.

regular-expression: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.

Description

Use the display bgp ipv6 peer received ipv6-prefix command to display the prefix entries in the ORF information of the specified BGP peer.

Examples

# Display the prefix information in the ORF packet from the BGP peer 4::4.

<Sysname> display bgp ipv6 peer 4::4 received ipv6-prefix

ORF ipv6-prefix entries: 2

ge: greater-equal le: less-equal

index rule prefix ge le

10 permit 1::/64 80 128

20 deny 100::/64 80 128

Table 8 Output description

Field	Description
ORF ipv6-prefix entries	Number of ORF prefix entries.
index	Index of a prefix entry.
rule	Matching rule of the prefix.
prefix	Prefix information.
ge	greater-equal, indicating the mask length must be greater than or equal to the specific value.
le	less-equal, indicating the mask length must be less than or equal to the specific value.

display bgp ipv6 routing-table

Syntax

display bgp ipv6 routing-table [ ipv6-address prefix-length ] [ | { begin | exclude | include } regular-expression ]

View

Any view

Default level

1: Monitor level

Parameters

ipv6-address: Destination IPv6 address.

prefix-length: Prefix length of the IPv6 address, in the range 0 to 128.

|: Filters command output by specifying a regular expression. For more information about regular expressions, see Fundamentals Configuration Guide.

begin: Displays the first line that matches the specified regular expression and all lines that follow.

include: Displays all lines that match the specified regular expression.

regular-expression: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.

Description

Use the display bgp ipv6 routing-table command to display IPv6 BGP routing table information.

Examples

# Display the IPv6 BGP routing table.

<Sysname> display bgp ipv6 routing-table

Total Number of Routes: 2

BGP Local router ID is 30.30.30.1

Status codes: * - valid, ^ - VPNv4 best, > - best, d - damped,

h - history, i - internal, s - suppressed, S - Stale

Origin : i - IGP, e - EGP, ? - incomplete

*> Network : 30:30:: PrefixLen : 64

NextHop : 30:30::30:1 LocPrf :

PrefVal : 0 Label : NULL

MED :0

Path/Ogn: i

*> Network : 40:40:: PrefixLen : 64

NextHop : 40:40::40:1 LocPrf :

PrefVal : 0 Label : NULL

MED : 0

Path/Ogn: i

Table 9 Output description

Field	Description
Local router ID	Local router ID.
Status codes	Status codes: · * – valid—Valid route. · ^ - VPNv4 best—Best VPNv4 route. · > – best—Best route. · d – damped—Dampened route. · h – history—History route. · i – internal—Internal route. · s –suppressed—Suppressed route. · S – Stale—Stale route.
Origin	Origin attributes: · i – IGP—Originated in the AS. · e – EGP—Learned through EGP. · ? – incomplete—Learned by other means.
Network	Destination network address.
PrefixLen	Prefix length.
NextHop	Next Hop.
MED	MULTI_EXIT_DISC attribute.
LocPrf	Local preference value.
Path	AS_PATH attribute, recording the ASs the packet has passed to avoid routing loops.
PrefVal	Preferred value.
Label	Label.
Ogn	Origin attribute of the route, which can take on one of the following values: · i—Indicates that a route is interior to the AS. Summary routes and the routes configured using the network command are considered IGP routes. · e—Indicates that a route is learned from the exterior gateway protocol (EGP). · ?—Short for INCOMPLETE. It indicates that the origin of a route is unknown and the route is learned by other means. BGP sets Origin attribute of routes learned from other IGP protocols to INCOMPLETE.

display bgp ipv6 routing-table as-path-acl

Syntax

display bgp ipv6 routing-table as-path-acl as-path-acl-number [ | { begin | exclude | include } regular-expression ]

View

Any view

Default level

1: Monitor level

Parameters

as-path-acl-number: Number of an AS path ACL permitted by which to display routing information, ranging from 1 to 256.

|: Filters command output by specifying a regular expression. For more information about regular expressions, see Fundamentals Configuration Guide.

begin: Displays the first line that matches the specified regular expression and all lines that follow.

include: Displays all lines that match the specified regular expression.

regular-expression: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.

Description

Use the display bgp ipv6 routing-table as-path-acl command to display routes filtered through the specified AS path ACL.

Examples

# Display routes filtered through the AS path ACL 20.

<Sysname> display bgp ipv6 routing-table as-path-acl 20

BGP Local router ID is 30.30.30.1

Status codes: * - valid, ^ - VPNv4 best, > - best, d - damped,

h - history, i - internal, s - suppressed, S - Stale

Origin : i - IGP, e - EGP, ? - incomplete

*> Network : 30:30:: PrefixLen : 64

NextHop : 30:30::30:1 LocPrf :

PrefVal : 0 Label : NULL

MED : 0

Path/Ogn: i

For description of the fields, see Table 9.

display bgp ipv6 routing-table community

Syntax

display bgp ipv6 routing-table community [ aa:nn&<1-13> ] [ no-advertise | no-export | no-export-subconfed ] * [ whole-match ] [ | { begin | exclude | include } regular-expression ]

View

Any view

Default level

1: Monitor level

Parameters

aa:nn: Community number; both aa and nn are in the range 0 to 65535.

&<1-13>: Indicates the argument before it can be entered up to 13 times.

no-advertise: Displays IPv6 BGP routes that cannot be advertised to any peer.

no-export: Displays IPv6 BGP routes that cannot be advertised out the AS; if a confederation exists, it displays IPv6 BGP routes that cannot be advertised out the confederation, but can be advertised to other sub ASs in the confederation.

no-export-subconfed: Displays IPv6 BGP routes that cannot be advertised out the AS or to other sub ASs if a confederation is configured.

whole-match: Displays the IPv6 BGP routes exactly matching the specified community attribute.

|: Filters command output by specifying a regular expression. For more information about regular expressions, see Fundamentals Configuration Guide.

begin: Displays the first line that matches the specified regular expression and all lines that follow.

include: Displays all lines that match the specified regular expression.

regular-expression: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.

Description

Use the display bgp ipv6 routing-table community command to display the routing information with the specified community attribute.

Examples

# Display the routing information with community attribute no-export.

<Sysname> display bgp ipv6 routing-table community no-export

BGP Local router ID is 30.30.30.1

Status codes: * - valid, ^ - VPNv4 best, > - best, d - damped,

h - history, i - internal, s - suppressed, S - Stale

Origin : i - IGP, e - EGP, ? - incomplete

*> Network : 30:30:: PrefixLen : 64

NextHop : 30:30::30:1 LocPrf :

PrefVal : 0 Label : NULL

MED : 0

Path/Ogn: i

For description of the fields, See Table 9.

display bgp ipv6 routing-table community-list

Syntax

display bgp ipv6 routing-table community-list { { basic-community-list-number | comm-list-name } [ whole-match ] | adv-community-list-number }&<1-16> [ | { begin | exclude | include } regular-expression ]

View

Any view

Default level

1: Monitor level

Parameters

basic-community-list-number: Specifies a basic community-list number, in the range 1 to 99.

adv-community-list-number: Specifies an advanced community-list number, in the range 100 to 199.

comm-list-name: Specifies a community list name, a string of 1 to 31 characters (not all are numbers).

whole-match: Displays routes exactly matching the specified basic-community-list-number.

&<1-16>: Specifies to allow entering the argument before it up to 16 times.

|: Filters command output by specifying a regular expression. For more information about regular expressions, see Fundamentals Configuration Guide.

begin: Displays the first line that matches the specified regular expression and all lines that follow.

include: Displays all lines that match the specified regular expression.

regular-expression: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.

Description

Use the display bgp ipv6 routing-table community-list command to view the routing information matching the specified IPv6 BGP community list.

Examples

# Display the routing information matching the specified IPv6 BGP community list.

<Sysname> display bgp ipv6 routing-table community-list 99

BGP Local router ID is 30.30.30.1

Status codes: * - valid, ^ - VPNv4 best, > - best, d - damped,

h - history, i - internal, s - suppressed, S - Stale

Origin : i - IGP, e - EGP, ? - incomplete

*> Network : 30:30:: PrefixLen : 64

NextHop : 30:30::30:1 LocPrf :

PrefVal : 0 Label : NULL

MED :0

Path/Ogn: i

For description of the fields, see Table 9.

display bgp ipv6 routing-table dampened

Syntax

display bgp ipv6 routing-table dampened [ | { begin | exclude | include } regular-expression ]

View

Any view

Default level

1: Monitor level

Parameters

|: Filters command output by specifying a regular expression. For more information about regular expressions, see Fundamentals Configuration Guide.

begin: Displays the first line that matches the specified regular expression and all lines that follow.

include: Displays all lines that match the specified regular expression.

regular-expression: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.

Description

Use the display bgp ipv6 routing-table dampened command to display the IPv6 BGP dampened routes.

Examples

# Display IPv6 BGP dampened routes.

<Sysname> display bgp ipv6 routing-table dampened

BGP Local router ID is 1.1.1.1

Status codes: * - valid, ^ - VPNv4 best, > - best, d - damped,

h - history, i - internal, s - suppressed, S - Stale

Origin : i - IGP, e - EGP, ? - incomplete

*d Network : 111:: PrefixLen : 64

From : 122::1 Reuse : 00:29:34

Path/Ogn: 200?

Table 10 Output description

Field	Description
From	Source IP address of a route
Reuse	Time for reuse

For description of the fields, see Table 9.

display bgp ipv6 routing-table dampening parameter

Syntax

display bgp ipv6 routing-table dampening parameter [ | { begin | exclude | include } regular-expression ]

View

Any view

Default level

1: Monitor level

Parameters

|: Filters command output by specifying a regular expression. For more information about regular expressions, see Fundamentals Configuration Guide.

begin: Displays the first line that matches the specified regular expression and all lines that follow.

include: Displays all lines that match the specified regular expression.

regular-expression: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.

Description

Use the display bgp ipv6 routing-table dampening parameter command to display IPv6 BGP routing dampening parameters.

Related commands: dampening.

Examples

# Display IPv6 BGP routing dampening parameters.

<Sysname> display bgp ipv6 routing-table dampening parameter

Maximum Suppress Time(in second) : 950

Ceiling Value : 3000

Reuse Value : 1000

Reach HalfLife Time(in second) : 600

Unreach HalfLife Time(in second) : 600

Suppress-Limit : 2000

Table 11 Output description

Field	Description
Maximum Suppress Time	Maximum Suppress Time
Ceiling Value	Upper limit of penalty value
Reuse Value	Reuse Value
Reach HalfLife Time(in second)	Half-life time of active routes
Unreach HalfLife Time(in second)	Half-life time of inactive routes
Suppress-Limit	Suppress value

display bgp ipv6 routing-table different-origin-as

Syntax

display bgp ipv6 routing-table different-origin-as [ | { begin | exclude | include } regular-expression ]

View

Any view

Default level

1: Monitor level

Parameters

|: Filters command output by specifying a regular expression. For more information about regular expressions, see Fundamentals Configuration Guide.

begin: Displays the first line that matches the specified regular expression and all lines that follow.

include: Displays all lines that match the specified regular expression.

regular-expression: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.

Description

Use the display bgp ipv6 routing-table different-origin-as command to display IPv6 BGP routes originating from different autonomous systems.

Examples

# Display routes from different ASs.

<Sysname> display bgp ipv6 routing-table different-origin-as

BGP Local router ID is 2.2.2.2

Status codes: * - valid, ^ - VPNv4 best, > - best, d - damped,

h - history, i - internal, s - suppressed, S - Stale

Origin : i - IGP, e - EGP, ? - incomplete

*> Network : 222:: PrefixLen : 64

NextHop : 122::2 LocPrf :

PrefVal : 0 Label : NULL

MED : 0

Path/Ogn: 100 ?

For description of the fields, see Table 9.

display bgp ipv6 routing-table flap-info

Syntax

display bgp ipv6 routing-table flap-info [ regular-expression as-regular-expression | [ as-path-acl as-path-acl-number | ipv6-address prefix-length [ longer-match ] ] [ | { begin | exclude | include } regular-expression ] ]

View

Any view

Default level

1: Monitor level

Parameters

as-regular-expression: AS path regular expression to be matched, a string of 1 to 80 characters.

as-path-acl-number: Number of the specified AS path ACL to be matched, ranging from 1 to 256.

ipv6-address: IPv6 address of a route to be displayed.

prefix-length: Prefix length of the IPv6 address, in the range 0 to 128.

longer-match: Matches the longest prefix.

|: Filters command output by specifying a regular expression. For more information about regular expressions, see Fundamentals Configuration Guide.

begin: Displays the first line that matches the specified regular expression and all lines that follow.

include: Displays all lines that match the specified regular expression.

regular-expression: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.

Description

Use the display bgp ipv6 routing-table flap-info command to display IPv6 BGP route flap statistics.

Examples

# Display IPv6 BGP route flap statistics.

<Sysname> display bgp ipv6 routing-table flap-info

BGP Local router ID is 1.1.1.1

Status codes: * - valid, ^ - VPNv4 best, > - best, d - damped,

h - history, i - internal, s - suppressed, S - Stale

Origin : i - IGP, e - EGP, ? - incomplete

*d Network : 111:: PrefixLen : 64

From : 122::1 Flaps : 3

Duration : 00:13:47 Reuse : 00:16:36

Path/Ogn : 200?

Table 12 Output description

Field	Description
Flaps	Number of flaps
Duration	Flap duration
Reuse	Reuse time of the route

For description of the fields, see Table 9.

display bgp ipv6 routing-table label

Syntax

display bgp ipv6 routing-table label [ | { begin | exclude | include } regular-expression ]

View

Any view

Default level

1: Monitor level

Parameters

|: Filters command output by specifying a regular expression. For more information about regular expressions, see Fundamentals Configuration Guide.

begin: Displays the first line that matches the specified regular expression and all lines that follow.

include: Displays all lines that match the specified regular expression.

regular-expression: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.

Description

Use the display bgp ipv6 routing-table label command to display IPv6 BGP label routing information.

Examples

# Display IPv6 BGP label routing information.

<Sysname> display bgp ipv6 routing-table label

Total Number of Routes: 1

Network Prefix NextHop In/Out Label

200:: 96 ::FFFF:2.1.1.1 NULL/1024

Table 13 Output description

Field	Description
Network	Network address
Prefix	Prefix length
NextHop	Next hop
In/Out Label	MPLS incoming/outgoing label information

display bgp ipv6 routing-table peer

Syntax

display bgp ipv6 routing-table peer { ipv4-address | ipv6-address } { advertised-routes | received-routes } [ network-address prefix-length | statistic ] [ | { begin | exclude | include } regular-expression ]

View

Any view

Default level

1: Monitor level

Parameters

ipv4-address: Specifies the IPv4 peer to be displayed.

ipv6-address: Specifies the IPv6 peer to be displayed.

advertised-routes: Routing information advertised to the specified peer.

received-routes: Routing information received from the specified peer.

network-address prefix-length: IPv6 address and prefix length. The prefix length ranges from 0 to 128.

statistic: Displays route statistics.

|: Filters command output by specifying a regular expression. For more information about regular expressions, see Fundamentals Configuration Guide.

begin: Displays the first line that matches the specified regular expression and all lines that follow.

include: Displays all lines that match the specified regular expression.

regular-expression: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.

Description

Use the display bgp ipv6 routing-table peer command to display the routing information advertised to or received from the specified IPv4 or IPv6 BGP peer.

Examples

# Display the routing information advertised to the specified BGP peer.

<Sysname> display bgp ipv6 routing-table peer 10:10::10:1 advertised-routes

Total Number of Routes: 2

BGP Local router ID is 20.20.20.1

Status codes: * - valid, ^ - VPNv4 best, > - best, d - damped,

h - history, i - internal, s - suppressed, S - Stale

Origin : i - IGP, e - EGP, ? - incomplete

*> Network : 20:20:: PrefixLen : 64

NextHop : 20:20::20:1 LocPrf :

PrefVal : 0 Label : NULL

MED : 0

Path/Ogn: i

*> Network : 40:40:: PrefixLen : 64

NextHop : 30:30::30:1 LocPrf :

PrefVal : 0 Label : NULL

MED : 0

Path/Ogn: 300 i

For description of the fields, see Table 9.

display bgp ipv6 routing-table regular-expression

Syntax

display bgp ipv6 routing-table regular-expression as-regular-expression

View

Any view

Default level

1: Monitor level

Parameters

as-regular-expression: AS regular expression, a string of 1 to 80 characters.

Description

Use the display bgp ipv6 routing-table regular-expression command to display the routes permitted by the specified AS regular expression.

Examples

# Display routing information matching the specified AS regular expression.

<Sysname> display bgp ipv6 routing-table regular-expression ^100

BGP Local router ID is 20.20.20.1

Status codes: * - valid, ^ - VPNv4 best, > - best, d - damped,

h - history, i - internal, s - suppressed, S - Stale

Origin : i - IGP, e - EGP, ? - incomplete

*> Network : 50:50:: PrefixLen : 64

NextHop : 10:10::10:1 LocPrf :

PrefVal : 0 Label : NULL

MED : 0

Path/Ogn: 100 i

For description of the fields, see Table 9.

display bgp ipv6 routing-table statistic

Syntax

display bgp ipv6 routing-table statistic [ | { begin | exclude | include } regular-expression ]

View

Any view

Default level

1: Monitor level

Parameters

|: Filters command output by specifying a regular expression. For more information about regular expressions, see Fundamentals Configuration Guide.

begin: Displays the first line that matches the specified regular expression and all lines that follow.

include: Displays all lines that match the specified regular expression.

regular-expression: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.

Description

Use the display bgp ipv6 routing-table statistic command to display IPv6 BGP routing statistics.

Examples

# Display IPv6 BGP routing statistics.

<Sysname> display bgp ipv6 routing-table statistic

Total Number of Routes: 1

filter-policy export (IPv6 address family view/IPv6 BGP-VPN instance view)

Syntax

filter-policy { acl6-number | ipv6-prefix ipv6-prefix-name } export [ protocol process-id ]

undo filter-policy export [ protocol process-id ]

View

IPv6 address family view, IPv6 BGP-VPN instance view

Default level

2: System level

Parameters

acl6-number: Specifies the number of an ACL6 used to match against the destination of routing information. The number is in the range 2000 to 3999.

ipv6-prefix-name: Specifies the name of an IPv6 prefix list used to match against the destination of routing information. The name is a string of 1 to 19 characters.

protocol: Filters routes redistributed from the routing protocol. It can be direct, isisv6, ospfv3, ripng, or static. If no protocol is specified, all routes will be filtered when advertised.

process-id: Process ID of the routing protocol, in the range 1 to 65535. It is available only when the protocol is isisv6, ospfv3 or ripng.

Description

Use the filter-policy export command to filter outbound routes using a specified filter.

Use the undo filter-policy export command to cancel filtering outbound routes.

By default, no outbound routing information is filtered.

If a protocol is specified, only routes redistributed from the specified protocol are filtered. If no protocol is specified, all redistributed routes will be filtered.

NOTE:

If you want to reference an advanced ACL (with a number from 3000 to 3999) in the command, the ACL should be configured with the rule [ rule-id ] { deny | permit } ipv6 source sour sour-prefix command to deny/permit a route with the specified destination, or with the rule [ rule-id ] { deny | permit } ipv6 source sour sour-prefix destination dest dest-prefix command to deny/permit a route with the specified destination and prefix. The source keyword specifies the destination address of a route and the destination keyword specifies the prefix of the route (the prefix must be valid; otherwise, the configuration is ineffective).

Examples

# Reference ACL6 2001 to filter all outbound IPv6 BGP routes.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] filter-policy 2001 export

# Configure ACL6 3000 to permit only route 2001::1/128 to pass, and reference ACL6 3000 to filter outbound routes.

<Sysname> system-view

[Sysname] acl ipv6 number 3000

[Sysname-acl6-adv-3000] rule 10 permit ipv6 source 2001::1 128 destination ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff 128

[Sysname-acl6-adv-3000] rule 100 deny ipv6

[Sysname-acl6-adv-3000] quit

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] filter-policy 3000 export

filter-policy import (IPv6 address family view/IPv6 BGP-VPN instance view)

Syntax

filter-policy { acl6-number | ipv6-prefix ipv6-prefix-name } import

undo filter-policy import

View

IPv6 address family view, IPv6 BGP-VPN instance view

Default level

2: System level

Parameters

acl6-number: Number of an IPv6 ACL used to match against the destination address field of routing information, ranging from 2000 to 3999.

ipv6-prefix-name: Name of an IPv6 prefix list used to match against the destination address field of routing information, a string of 1 to 19 characters.

Description

Use the filter-policy import command to filter inbound routing information using a specified filter.

Use the undo filter-policy import command to cancel filtering inbound routing information.

By default, no inbound routing information is filtered.

NOTE:

Examples

# Reference ACL6 2001 to filter all inbound routes.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] filter-policy 2001 import

# Configure ACL6 3000 to permit only route 2001::1/128 to pass, and reference ACL6 3000 to filter inbound routes.

<Sysname> system-view

[Sysname] acl ipv6 number 3000

[Sysname-acl6-adv-3000] rule 10 permit ipv6 source 2001::1 128 destination ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff 128

[Sysname-acl6-adv-3000] rule 100 deny ipv6

[Sysname-acl6-adv-3000] quit

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] filter-policy 3000 import

group (IPv6 address family view)

Syntax

group ipv6-group-name [ internal | external ]

undo group ipv6-group-name

View

IPv6 address family view

Default level

2: System level

Parameters

ipv6-group-name: Name of an IPv6 peer group, a string of 1 to 47 characters.

internal: Creates an IBGP peer group.

external: Creates an EBGP peer group, which can be a group of another sub AS in the confederation.

Description

Use the group command to create a peer group.

Use the undo group command to delete a peer group.

An IBGP peer group will be created if neither internal nor external is selected.

Examples

# Create an IBGP peer group named test.

<Sysname> system-view

[Sysname] bgp 100

[Sysname] ipv6-family

[Sysname-bgp-af-ipv6] group test

import-route (IPv6 address family view/IPv6 BGP-VPN instance view)

Syntax

import-route protocol [ process-id [ med med-value | route-policy route-policy-name ] * ]

undo import-route protocol [ process-id ]

View

IPv6 address family view, IPv6 BGP-VPN instance view

Default level

2: System level

Parameters

protocol: Redistributes routes from the specified protocol, which can be direct, isisv6, ospfv3, ripng and static.

process-id: Process ID, in the range 1 to 65535. The default is 1. It is available only when the protocol is isisv6, ospfv3 or ripng.

med-value: Applies the MED value to redistributed routes. The value is in the range 0 to 4294967295. If not specified, the cost of the redistributed route is used as its MED in the IPv6 BGP routing domain.

route-policy-name: Name of a routing policy used to filter redistributed routes, a string of 1 to 63 characters.

Description

Use the import-route command to redistribute routes from another routing protocol.

Use the undo import-route command to remove the configuration.

By default, IPv6 BGP does not redistribute routes from any routing protocol.

The routes redistributed using the import-route command has the incomplete origin attribute.

Examples

# Redistribute routes from RIPng 1.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] import-route ripng 1

ipv6-family

Syntax

ipv6-family [ vpnv6 | vpn-instance vpn-instance-name ]

undo ipv6-family [ vpnv6 | vpn-instance vpn-instance-name ]

View

BGP view

Default level

2: System level

Parameters

vpnv6: Enters BGP-VPNv6 address family view.

vpn-instance vpn-instance-name: Enters IPv6 BGP-VPN instance view. vpn-instance-name is a string of 1 to 31 case-sensitive characters.

Description

Use the ipv6-family command to enter IPv6 address family view.

Use the undo ipv6-family command to remove all configurations from the view.

Use the ipv6-family vpnv6 command to enter BGP-VPNv6 address family view.

Use the undo ipv6-family vpnv6 command to remove all configurations from the view.

Use the ipv6-family vpn-instance vpn-instance-name command to enter IPv6 BGP-VPN instance view.

Use the undo ipv6-family vpn-instance vpn-instance-name command to remove all configurations from the view.

IPv4 BGP unicast view is the default.

Before entering IPv6 BGP-VPN instance view, you must create the VPN instance.

Examples

# Enter IPv6 address family view.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6]

# Enter IPv6 BGP-VPN instance view.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family vpn-instance vpn1

[Sysname-bgp-ipv6-vpn1]

# Enter BGP-VPNv6 address family view.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family vpnv6

[Sysname-bgp-af-vpnv6]

network (IPv6 address family view/IPv6 BGP-VPN instance view)

Syntax

network ipv6-address prefix-length [ route-policy route-policy-name | short-cut ]

undo network ipv6-address prefix-length [ short-cut ]

View

IPv6 address family view, IPv6 BGP-VPN instance view

Default level

2: System level

Parameters

ipv6-address: IPv6 address.

prefix-length: Prefix length of the address, in the range 0 to 128.

route-policy-name: Name of a routing policy, a string of 1 to 63 characters.

short-cut: If the keyword is specified for an EBGP route, the route will use the local routing management value rather than that of EBGP routes, so the preference of the route is reduced.

Description

Use the network command to advertise a network to the IPv6 BGP routing table.

Use the undo network command to remove an entry from the IPv6 BGP routing table.

By default, no route is advertised.

The route to be advertised must exist in the local IP routing table, and using a routing policy makes route management more flexible.

The route advertised to the BGP routing table using the network command has the IGP origin attribute.

Examples

# Advertise the network 2002::/16 into the IPv6 BGP routing table.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] network 2002:: 16

peer advertise-community (IPv6 address family view)

Syntax

peer { group-name | ipv4-address | ipv6-address } advertise-community

undo peer { group-name | ipv4-address | ipv6-address } advertise-community

View

IPv6 address family view

Default level

2: System level

Parameters

group-name: Name of an IPv4 or IPv6 peer group, a string of 1 to 47 characters.

ipv4-address: IPv4 address of a peer.

ipv6-address: IPv6 address of a peer.

Description

Use the peer advertise-community command to advertise the community attribute to a peer/peer group.

Use the undo peer advertise-community command to remove the configuration.

By default, no community attribute is advertised to any peer group/peer.

Examples

# Advertise the community attribute to the peer 1:2::3:4.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] peer 1:2::3:4 advertise-community

peer advertise-ext-community (IPv6 address family view)

Syntax

peer { group-name | ipv4-address | ipv6-address } advertise-ext-community

undo peer { group-name | ipv4-address | ipv6-address } advertise-ext-community

View

IPv6 address family view

Default level

2: System level

Parameters

group-name: Name of an IPv4 or IPv6 peer group, a string of 1 to 47 characters.

ipv4-address: IPv4 address of a peer.

ipv6-address: IPv6 address of a peer.

Description

Use the peer advertise-ext-community command to advertise the extended community attribute to a peer/peer group.

Use the undo peer advertise-ext-community command to remove the configuration.

By default, no extended community attribute is advertised to a peer/peer group.

Examples

# Advertise the extended community attribute to the peer 1:2::3:4.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] peer 1:2::3:4 advertise-ext-community

peer allow-as-loop (IPv6 address family view)

Syntax

peer { group-name | ipv4-address | ipv6-address } allow-as-loop [ number ]

undo peer { group-name | ipv4-address | ipv6-address } allow-as-loop

View

IPv6 address family view

Default level

2: System level

Parameters

group-name: Name of an IPv4 or IPv6 peer group, a string of 1 to 47 characters.

ipv4-address: IPv4 address of a peer.

ipv6-address: IPv6 address of a peer.

number: Specifies the number of times for which the local AS number can appear in routes from the peer/peer group, in the range 1 to 10. The default number is 1.

Description

Use the peer allow-as-loop command to configure IPv6 BGP to allow the local AS number to exist in the AS_PATH attribute of routes from a peer/peer group, and to configure the times for which it can appear.

Use the undo peer allow-as-loop command to disable the function.

The local AS number is not allowed to exist in the AS PATH attribute of routes by default.

Examples

# Configure the number of times for which the local AS number can appear in the AS PATH of routes from peer 1::1 as 2.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] peer 1::1 allow-as-loop 2

peer as-number (IPv6 address family view)

Syntax

peer { ipv6-group-name | ipv6-address } as-number as-number

undo peer ipv6-group-name as-number

undo peer ipv6-address

View

IPv6 address family view

Default level

2: System level

Parameters

ipv6-group-name: Name of a peer group, a string of 1 to 47 characters.

ipv6-address: IPv6 address of a peer.

as-number: AS number of the peer/peer group, in the range 1 to 4294967295.

Description

Use the peer as-number command to configure an IPv6 peer/peer group.

Use the undo peer ipv6-group-name as-number command to delete an IPv6 peer group.

Use the undo peer ipv6-address command to delete a peer.

Examples

# Configure peer group test in AS 200.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] group test external

[Sysname-bgp-af-ipv6] peer test as-number 200

peer as-number (IPv6 BGP-VPN instance view)

Syntax

peer ipv6-address as-number as-number

undo peer ipv6-address

View

IPv6 BGP-VPN instance view

Default level

2: System level

Parameters

ipv6-address: IPv6 address of a peer.

as-number: AS number of the peer/peer group, in the range 1 to 4294967295.

Description

Use the peer as-number command to configure an IPv6 peer/peer group.

Use the undo peer ipv6-address command to delete a peer.

Examples

# Configure peer 2001::1 in AS 200.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family vpn-instance vpn1

[Sysname-bgp-ipv6-vpn1] peer 2001::1 as-number 200

peer as-path-acl (IPv6 address family view)

Syntax

peer { group-name | ipv4-address | ipv6-address } as-path-acl as-path-acl-number { import | export }

undo peer { group-name | ipv4-address | ipv6-address } as-path-acl as-path-acl-number { import | export }

View

IPv6 address family view

Default level

2: System level

Parameters

group-name: Name of an IPv4 or IPv6 peer group, a string of 1 to 47 characters.

ipv4-address: IPv4 address of a peer.

ipv6-address: IPv6 address of a peer.

as-path-acl-number: Number of an AS path ACL, in the range 1 to 256.

import: Filters incoming routes.

export: Filters outgoing routes.

Description

Use the peer as-path-acl command to specify an AS path ACL to filter routes incoming from or outgoing to a peer/peer group.

Use the undo peer as-path-acl command to remove the configuration.

By default, no AS path list is specified for filtering.

Examples

# Specify the AS path ACL 3 to filter routes outgoing to the peer 1:2::3:4.

<Sysname> system-view

[Sysname] ip as-path 3 permit ^200

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] peer 1:2::3:4 as-path-acl 3 export

peer bfd (IPv6 address family view/IPv6 BGP-VPN instance view)

Syntax

peer ipv6-address bfd

undo peer ipv6-address bfd

View

IPv6 address family view, IPv6 BGP-VPN instance view

Default level

2: System level

Parameters

ip-address: IPv6 address of a peer.

Description

Use the peer bfd command to enable BFD over the link to a BGP peer.

Use the undo peer bfd command to restore the default.

By default, BFD is not enabled for any BGP peer.

After a link failure occurs, BFD may detect the failure before the system performs GR, and as a result, GR will fail. Therefore, if GR capability is enabled for IPv6 BGP, use BFD with caution.

Examples

# Enable BFD over the link to BGP peer 100::1.

<Sysname> system-view

[Sysname] bgp 100

[Sysname] ipv6-family

[Sysname-bgp-af-ipv6] peer 100::1 bfd

peer capability-advertise orf

Syntax

peer { group-name | ip-address | ipv6-address } capability-advertise orf ipv6-prefix { both | receive | send }

undo peer { group-name | ip-address | ipv6-address } capability-advertise orf ipv6-prefix { both | receive | send }

View

IPv6 address family view

Default level

2: System level

Parameters

group-name: Name of a peer group, a string of 1 to 47 characters.

ip-address: IP address of a peer.

ipv6-address: IPv6 address of a peer.

both: Supports sending and receiving route-refresh messages carrying the ORF information.

receive: Supports receiving route-refresh messages carrying the ORF information.

send: Supports sending route-refresh messages carrying the ORF information.

Description

Use the peer capability-advertise orf command to enable the ORF capability for a BGP peer or peer group.

Use the undo peer capability-advertise orf command to disable the ORF capability for the BGP peer or peer group.

By default, the ORF capability is not enabled for a BGP peer or peer group.

· After you enable the ORF capability, the local BGP router negotiates the ORF capability with the BGP peer through Open messages. After that, the BGP router can process route-refresh messages carrying the standard ORF information from the peer or send route-refresh messages carrying the standard ORF information to the peer. For non-standard ORF capability negotiation, you need also to configure the peer capability-advertise orf non-standard command.

· After you disable the ORF capability, the local BGP router does not negotiate the ORF capability with the specified peer or peer group.

Table 14 Description of the both, send, and receive parameters and the negotiation result

Local parameter	Peer parameter	Negotiation result
send	· receive · both	The ORF sending capability is enabled locally and the ORF receiving capability is enabled on the peer.
receive	· send · both	The ORF receiving capability is enabled locally and the ORF sending capability is enabled on the peer.
both	both	Both the ORF sending and receiving capabilities are enabled locally and on the peer, respectively.

Examples

# Enable the ORF capability for the BGP peer 1:2::3:4. Then, after negotiation, the local router can exchange ORF information with the peer 1:2::3:4.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] peer 1:2::3:4 as-number 100

[Sysname-bgp-af-ipv6] peer 1:2::3:4 capability-advertise orf ipv6-prefix both

peer capability-advertise orf non-standard (IPv6 address family view)

Syntax

peer { group-name | ipv6-address } capability-advertise orf non-standard

undo peer { group-name | ipv6-address } capability-advertise orf non-standard

View

IPv6 address family view

Default level

2: System level

Parameters

group-name: Name of a peer group, a string of 1 to 47 characters.

ipv6-address: IPv6 address of a peer.

Parameters

Use the peer capability-advertise orf non-standard command to enable the non-standard ORF capability (the early implementation of ORF is different from that defined in RFC) for a BGP peer or peer group.

Use the undo peer capability-advertise orf non-standard command to disable the non-standard ORF capability for the BGP peer or peer group.

By default, the non-standard ORF capability is not enabled for a BGP peer or peer group.

This command needs to be configured when the peer supports only non-standard ORF.

Related commands: peer capability-advertise orf.

Examples

# Enable the non-standard ORF capability for the BGP peer 1:2::3:4 (suppose the BGP peer 1:2::3:4 can only send non-standard ORF packets).

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] peer 1:2::3:4 as-number 100

[Sysname-bgp-af-ipv6] peer 1:2::3:4 capability-advertise orf non-standard

[Sysname-bgp-af-ipv6] peer 1:2::3:4 capability-advertise orf ip-prefix both

peer capability-advertise route-refresh

Syntax

peer { ipv6-group-name | ipv6-address } capability-advertise route-refresh

undo peer { ipv6-group-name | ipv6-address } capability-advertise route-refresh

View

IPv6 address family view

Default level

2: System level

Parameters

ipv6-group-name: Name of a peer group, a string of 1 to 47 characters.

ipv6-address: IPv6 address of a peer.

Description

Use the peer capability-advertise route-refresh command to enable IPv6 BGP route-refresh.

Use the undo peer capability-advertise route-refresh command to disable the function.

By default, route-refresh is enabled.

Examples

# Disable route-refresh of peer 1:2::3:4.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] peer 1:2::3:4 as-number 100

[Sysname-bgp-af-ipv6] undo peer 1:2::3:4 capability-advertise route-refresh

peer capability-advertise suppress-4-byte-as (IPv6 address family view)

Syntax

peer { group-name | ipv6-address } capability-advertise suppress-4-byte-as

undo peer { group-name | ipv6-address } capability-advertise suppress-4-byte-as

View

IPv6 address family view

Default level

2: System level

Parameters

group-name: Name of a peer group, a string of 1 to 47 characters.

ipv6-address: IPv6 address of a peer.

Description

Use the peer capability-advertise suppress-4-byte-as command to enable 4-byte AS number suppression.

Use the undo peer capability-advertise suppress-4-byte-as command to disable the function.

By default, the 4-byte AS number suppression function is disabled.

The device supports 4-byte AS numbers and uses 4-byte AS numbers by default. If the peer devices support only 2-byte AS numbers, you must enable the 4-byte AS number suppression function on the device.

If the peer device supports 4-byte AS numbers, do not enable the suppression function; otherwise, the BGP peer relationship cannot be established.

Examples

# In IPv6 address family view, enable 4-byte AS number suppression for peer 2001::1.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp] peer 2001::1 as-number 200

[Sysname-bgp] peer 2001::1 capability-advertise suppress-4-byte-as

peer capability-advertise suppress-4-byte-as (IPv6 BGP-VPN instance view)

Syntax

peer ipv6-address capability-advertise suppress-4-byte-as

undo peer ipv6-address capability-advertise suppress-4-byte-as

View

IPv6 BGP-VPN instance view

Default level

2: System level

Parameters

ipv6-address: IPv6 address of a peer.

Description

Use the peer capability-advertise suppress-4-byte-as command to enable 4-byte AS number suppression.

Use the undo peer capability-advertise suppress-4-byte-as command to disable the function.

By default, the 4-byte AS number suppression function is disabled.

If the peer device supports 4-byte AS numbers, do not enable the suppression function; otherwise, the BGP peer relationship cannot be established.

Examples

# In IPv6 BGP-VPN instance view, enable 4-byte AS number suppression for peer 2001::1.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family vpn-instance 11

[Sysname-bgp-ipv6-11] peer 2001::1 as-number 200

[Sysname-bgp-ipv6-11] peer 2001::1 capability-advertise suppress-4-byte-as

peer connect-interface (IPv6 address family view)

Syntax

peer { ipv6-group-name | ipv6-address } connect-interface interface-type interface-number

undo peer { ipv6-group-name | ipv6-address } connect-interface

View

IPv6 address family view

Default level

2: System level

Parameters

ipv6-group-name: Name of a peer group, a string of 1 to 47 characters.

ipv6-address: IPv6 address of a peer.

interface-type interface-number: Specifies an interface by its type and number.

Description

Use the peer connect-interface command to specify the source interface for establishing TCP connections to an IPv6 BGP peer or peer group.

Use the undo peer connect-interface command to restore the default.

By default, BGP uses the outbound interface of the best route to the IPv6 BGP peer/peer group as the source interface for establishing a TCP connection.

To establish multiple BGP connections to a BGP router, you need to specify on the local router the respective source interfaces for establishing TCP connections to the peers on the peering BGP router; otherwise, the local BGP router may fail to establish TCP connections to the peers when using the outbound interfaces of the best routes as the source interfaces.

Examples

# Specify loopback 0 as the source interface for routing updates to peer 1:2::3:4.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] peer 1:2::3:4 connect-interface loopback 0

peer default-route-advertise

Syntax

peer { group-name | ipv4-address | ipv6-address } default-route-advertise [ route-policy route-policy-name ]

undo peer { group-name | ipv4-address | ipv6-address } default-route-advertise

View

IPv6 address family view

Default level

2: System level

Parameters

group-name: Name of an IPv4 or IPv6 peer group, a string of 1 to 47 characters.

ipv4-address: IPv4 address of a peer.

ipv6-address: IPv6 address of a peer.

route-policy-name: Name of a routing policy, a string of 1 to 63 characters.

Description

Use the peer default-route-advertise command to advertise a default route to a peer/peer group.

Use the undo peer default-route-advertise command to disable advertising a default route.

By default, no default route is advertised to a peer/peer group.

Using this command does not require the default route available in the routing table. With this command used, the router sends the default route unconditionally to the peer/peer group with the next hop being itself.

Examples

# Advertise a default route to peer 1:2::3:4.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] peer 1:2::3:4 default-route-advertise

peer description (IPv6 address family view)

Syntax

peer { ipv6-group-name | ipv6-address } description description-text

undo peer { ipv6-group-name | ipv6-address } description

View

IPv6 address family view

Default level

2: System level

Parameters

ipv6-group-name: Name of a peer group, a string of 1 to 47 characters.

ipv6-address: IPv6 address of a peer.

description-text: Description information for the peer/peer group, a string of 1 to 79 characters.

Description

Use the peer description command to configure the description information for a peer/peer group.

Use the undo peer description command to remove the description information of a peer/peer group.

By default, no description information is configured for a peer (group).

You need create a peer/peer group before configuring a description for it.

Examples

# Configure the description for the peer group test as ISP1.

<Sysname] system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] group test external

[Sysname-bgp-af-ipv6] peer test description ISP1

peer ebgp-max-hop (IPv6 address family view)

Syntax

peer { ipv6-group-name | ipv6-address } ebgp-max-hop [ hop-count ]

undo peer { ipv6-group-name | ipv6-address } ebgp-max-hop

View

IPv6 address family view

Default level

2: System level

Parameters

ipv6-group-name: Name of a peer group, a string of 1 to 47 characters.

ipv6-address: IPv6 address of a peer.

hop-count: Maximum hop count, in the range 1 to 255. By default, the value is 64.

Description

Use the peer ebgp-max-hop command to allow establishing the EBGP connection to a peer/peer group indirectly connected.

Use the undo peer ebgp-max-hop command to remove the configuration.

By default, this feature is disabled.

You can use the argument hop-count to specify the maximum router hops of the EBGP connection.

Examples

# Allow establishing the EBGP connection with the peer group test on an indirectly connected network.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] group test external

[Sysname-bgp-af-ipv6] peer test ebgp-max-hop

peer enable (IPv6 address family view)

Syntax

peer { ipv4-group-name | ipv4-address | ipv6-address } enable

undo peer { ipv4-group-name | ipv4-address | ipv6-address } enable

View

IPv6 address family view

Default level

2: System level

Parameters

ipv4-group-name: Name of an IPv4 peer group, a string of 1 to 47 characters. The IPv4 peer group should be created beforehand.

ipv4-address: IPv4 address of a peer.

ipv6-address: IPv6 address of a peer.

Description

Use the peer enable command to enable an IPv4 peer or peer group.

Use the undo peer enable command to disable an IPv4 peer or peer group.

By default, no IPv4 peer or peer group is enabled.

If an IPv4 peer or peer group is disabled, the router will not exchange routing information with it.

Examples

# Enable peer 1.1.1.1.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] peer 1.1.1.1 enable

# Enable peer 1::1.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] peer 1::1 group group1

[Sysname-bgp-af-ipv6] peer 1::1 enable

peer fake-as (IPv6 address family view)

Syntax

peer { ipv6-group-name | ipv6-address } fake-as as-number

undo peer { ipv6-group-name | ipv6-address } fake-as

View

IPv6 address family view

Default level

2: System level

Parameters

ipv6-group-name: Name of a peer group, a string of 1 to 47 characters.

ipv6-address: IPv6 address of a peer.

as-number: Local AS number, in the range 1 to 4294967295.

Description

Use the peer fake-as command to configure a fake local AS number for a peer or peer group.

Use the undo peer fake-as command to remove the configuration.

By default, no fake local AS number is configured for a peer or peer group.

Examples

# Configure a fake AS number of 200 for the peer group test.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] group test external

[Sysname-bgp-af-ipv6] peer test fake-as 200

peer filter-policy (IPv6 address family view)

Syntax

peer { group-name | ipv4-address | ipv6-address } filter-policy acl6-number { import | export }

undo peer { group-name | ipv4-address | ipv6-address } filter-policy [ acl6-number ] { import | export }

View

IPv6 address family view

Default level

2: System level

Parameters

group-name: Name of an IPv4 or IPv6 peer group, a string of 1 to 47 characters.

ipv4-address: IPv4 address of a peer.

ipv6-address: IPv6 address of a peer.

acl6-number: IPv6 ACL number, in the range 2000 to 3999.

import: Applies the filter-policy to routes received from the peer/peer group.

export: Applies the filter-policy to routes advertised to the peer/peer group.

Description

Use the peer filter-policy command to configure an ACL-based filter policy for a peer or peer group.

Use the undo peer filter-policy command to remove the configuration.

By default, no ACL-based filter policy is configured for a peer or peer group.

Examples

# Apply the ACL6 2000 to filter routes advertised to the peer 1:2::3:4.

<Sysname> system-view

[Sysname] acl ipv6 number 2000

[Sysname-acl6-basic-2000] rule permit source 2001:1:: 64

[Sysname-acl6-basic-2000] quit

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] peer 1:2::3:4 filter-policy 2000 export

peer group (IPv6 address family view)

Syntax

peer { ipv4-address | ipv6-address } group group-name [ as-number as-number ]

undo peer ipv6-address group group-name

View

IPv6 address family view

Default level

2: System level

Parameters

group-name: Name of an IPv4 or IPv6 peer group, a string of 1 to 47 characters.

ipv4-address: IPv4 address of a peer.

ipv6-address: IPv6 address of a peer.

as-number: Specifies the AS number of the peer/peer group, in the range 1 to 4294967295.

Description

Use the peer group command to add a peer to a configured peer group.

Use the undo peer group command to delete a specified peer from a peer group.

By default, the peer does not belong to any peer group.

Examples

# Create a peer group named test and add the peer 1:2::3:4 to the peer group.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] group test external

[Sysname-bgp-af-ipv6] peer 1:2::3:4 as-number 200

[Sysname-bgp-af-ipv6] peer 1:2::3:4 group test

peer ignore (IPv6 address family view)

Syntax

peer { ipv6-group-name | ipv6-address } ignore

undo peer { ipv6-group-name | ipv6-address } ignore

View

IPv6 address family view

Default level

2: System level

Parameters

ipv6-group-name: Name of a peer group, a string of 1 to 47 characters.

ipv6-address: IPv6 address of a peer.

Description

Use the peer ignore command to terminate the session to a peer or peer group.

Use the undo peer ignore command to remove the configuration.

By default, a router can establish sessions with a peer or peer group.

After the peer ignore command is executed, the system terminates the active session(s) with the specified peer or peer group and clears all the related routing information. For a peer group, all the sessions with the peer group will be torn down.

Examples

# Terminate the session with peer 1:2::3:4.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] peer 1:2::3:4 ignore

peer ipv6-prefix

Syntax

peer { group-name | ipv4-address | ipv6-address } ipv6-prefix ipv6-prefix-name { import | export }

undo peer { group-name | ipv4-address | ipv6-address } ipv6-prefix { import | export }

View

IPv6 address family view

Default level

2: System level

Parameters

group-name: Name of an IPv4 or IPv6 peer group, a string of 1 to 47 characters.

ipv4-address: IPv4 address of a peer.

ipv6-address: IPv6 address of a peer.

ipv6-prefix-name: IPv6 prefix list name, a string of 1 to 19 characters.

import: Applies the filtering policy to routes received from the specified peer/peer group.

export: Applies the filtering policy to routes advertised to the specified peer/peer group.

Description

Use the peer ipv6-prefix command to specify an IPv6 prefix list to filter routes incoming from or outgoing to a peer or peer group.

Use the undo peer ipv6-prefix command to remove the configuration.

By default, no IPv6 prefix list is specified for filtering.

Examples

# Reference the IPv6 prefix list list 1 to filter routes outgoing to peer 1:2::3:4.

<Sysname> system-view

[Sysname] ip ipv6-prefix list1 permit 2002:: 64

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] peer 1:2::3:4 ipv6-prefix list1 export

peer ipsec-policy (IPv6 address family view)

Syntax

peer { group-name | ipv6-address } ipsec-policy policy-name

undo peer { group-name | ipv6-address } ipsec-policy

View

IPv6 address family view

Default level

2: System level

Parameters

group-name: Name of an IPv6 peer group, a string of 1 to 47 characters.

ipv6-address: IPv6 address of a peer.

policy-name: IPsec policy name, a string of 1 to 15 characters.

Description

Use the peer ipsec-policy command to apply an IPsec policy to an IPv6 BGP peer or peer group.

Use the undo peer ipsec-policy command to remove the applied IPsec policy.

By default, no IPsec policy is applied to any peer or peer group.

· The IPsec policy to be applied must have been configured. Otherwise, the configuration fails.

· You also need to make IPsec policy configuration on the peer or peer group. Otherwise, the local router will not receive IPv6 BGP packets from the peer or peer group.

Examples

# Apply IPsec policy policy001 to IPv6 BGP peer 1212::1111.

<Sysname] system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] peer 1212::1111 ipsec-policy policy001

peer keep-all-routes (IPv6 address family view)

Syntax

peer { group-name | ipv4-address | ipv6-address } keep-all-routes

undo peer { group-name | ipv4-address | ipv6-address } keep-all-routes

View

IPv6 address family view

Default level

2: System level

Parameters

group-name: Name of an IPv4 or IPv6 peer group, a string of 1 to 47 characters.

ipv4-address: IPv4 address of a peer.

ipv6-address: IPv6 address of a peer.

Description

Use the peer keep-all-routes command to save the original routing information from a peer or peer group, including even routes that failed to pass the inbound policy.

Use the undo peer keep-all-routes command to disable this function.

By default, the function is not enabled.

Examples

# Save routing information from peer 1:2::3:4.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] peer 1:2::3:4 keep-all-routes

peer label-route-capability (IPv6 address family view)

Syntax

peer { ipv4-group-name | ipv4-address } label-route-capability

undo peer { ipv4-group-name | ipv4-address } label-route-capability

View

IPv6 address family view

Default level

2: System level

Parameters

ipv4-group-name: Name of an IPv4 peer group, a string of 1 to 47 characters. An IPv4 peer group must be created successfully in BGP view before being activated here.

ipv4-address: IPv4 address of a peer.

Description

Use the peer label-route-capability command to enable exchange of labeled IPv6 routes with the peer/peer group.

Use the undo peer label-route-capability command to disable exchange of labeled IPv6 routes with the peer/peer group.

By default, the feature is disabled.

Examples

# Enable exchange of labeled IPv6 routes with peer 2.2.2.2.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] peer 2.2.2.2 label-route-capability

peer log-change (IPv6 address family view)

Syntax

peer { ipv6-group-name | ipv6-address } log-change

undo peer { ipv6-group-name | ipv6-address } log-change

View

IPv6 address family view

Default level

2: System level

Parameters

ipv6-group-name: Name of a peer group, a string of 1 to 47 characters.

ipv6-address: IPv6 address of a peer.

Description

Use the peer log-change command to enable the logging of session state and event information of a specified peer or peer group.

Use the undo peer log-change command to remove the configuration.

The logging is enabled by default.

Examples

# Enable the logging of session state and event information of peer 1:2::3:4.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] peer 1:2::3:4 log-change

peer next-hop-local (IPv6 address family view)

Syntax

peer { ipv6-group-name | ipv6-address } next-hop-local

undo peer { ipv6-group-name | ipv6-address } next-hop-local

View

IPv6 address family view

Default level

2: System level

Parameters

ipv6-group-name: Name of a peer group, a string of 1 to 47 characters.

ipv6-address: IPv6 address of a peer.

Description

Use the peer next-hop-local command to configure the next hop of routes advertised to a peer/peer group as the local router.

Use the undo peer next-hop-local command to restore the default.

By default, the system sets the next hop of routes advertised to an EBGP peer/peer group to the local router, but does not change the next hop for routes outgoing to an IBGP peer/peer group.

Examples

# Set the next hop of routes advertised to IBGP peer group test to the router itself.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] group test internal

[Sysname-bgp-af-ipv6] peer test next-hop-local

peer password

Syntax

peer { group-name | ipv6-address } password { cipher | simple } password

undo peer { group-name | ipv6-address } password

View

IPv6 address family view

Default level

2: System level

Parameters

group-name: Name of a peer group, a string of 1 to 47 characters.

ipv6-address: IPv6 address of a peer.

cipher: Displays the configured password in cipher text format.

simple: Displays the configured password in plain text format.

password: Password, a string of 1 to 80 characters when the simple keyword is used, or when the cipher keyword and plain text password are used; a string of 24 or 108 characters when the cipher text password and the cipher keyword are used.

Description

Use the peer password command to configure BGP to perform MD5 authentication when a TCP connection is being established with a peer/peer group.

Use the undo peer password command to restore the default.

By default, no MD5 authentication is performed for TCP connection establishment.

The MD5 authentication requires that the two parties have the same authentication mode and password to establish TCP connection; otherwise, the TCP connection cannot be established due to authentication failure.

If the simple keyword is specified, the password in plain text is stored in the configurations file. You can use the display this and display current-configuration commands to display the plain-text password.

If the cipher keyword is specified and a plain-text password is entered, the password is stored in the configurations file after being encrypted. You can use the display this and display current-configuration commands to display the password in cipher text. Specify the password in cipher text so that the password cannot be easily cracked.

Examples

# Enable MD5 authentication for establishing TCP connection between the local router (1:2::3:3) and peer router (1:2::3:4), and configure the authentication password as aabbcc.

· On the local router:

<Sysname> system-view

[Sysname] bgp 3

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] peer 1:2::3:4 password cipher aabbcc

· On the peer router:

<Sysname> system-view

[Sysname] bgp 4

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] peer 1:2::3:3 password cipher aabbcc

peer preferred-value (IPv6 address family view)

Syntax

peer { ipv6-group-name | ipv6-address } preferred-value value

undo peer { ipv6-group-name | ipv6-address } preferred-value

View

IPv6 address family view

Default level

2: System level

Parameters

ipv6-group-name: Name of a peer group, a string of 1 to 47 characters.

ipv6-address: IPv6 address of a peer.

value: Preferred value, in the range 0 to 65535.

Description

Use the peer preferred-value command to assign a preferred value to routes received from a peer or peer group.

Use the undo peer preferred-value command to restore the default.

By default, routes received from a peer or peer group have a preferred value of 0.

Routes learned from peers each have an initial preferred value. Among multiple routes to the same destination, the route with the biggest value is selected.

NOTE:

If you both reference a routing policy and use the command peer { ipv6-group-name | ipv6-address } preferred-value value to set a preferred value for routes from a peer, the routing policy sets the specific preferred value for routes matching it. If the preferred value in the routing policy is zero, the routes use the value set with the peer { ipv6-group-name | ipv6-address } preferred-value value command. For how to use a routing policy to set a preferred value, see the command peer { group-name | ipv4-address | ipv6-address } route-policy route-policy-name { import | export } in this document, and the command apply preferred-value preferred-value in the chapter “Routing policy configuration commands.”

Examples

# Configure the preferred value as 50 for routes from peer 1:2::3:4.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] peer 1:2::3:4 preferred-value 50

peer preferred-value (IPv6 BGP-VPN instance view)

Syntax

peer ipv6-address preferred-value value

undo peer ipv6-address [ preferred-value ]

View

IPv6 BGP-VPN instance view

Default level

2: System level

Parameters

ipv6-address: IPv6 address of a peer.

value: Preferred value, in the range 0 to 65535.

Description

Use the peer preferred-value command to assign a preferred value to routes received from a peer or peer group.

Use the undo peer preferred-value command to restore the default.

By default, routes received from a peer or peer group have a preferred value of 0.

Routes learned from peers each have an initial preferred value. Among multiple routes to the same destination, the route with the biggest value is selected.

NOTE:

If you both reference a routing policy and use the command peer { ipv6-group-name | ipv6-address } preferred-value value to set a preferred value for routes from a peer, the routing policy sets the specific preferred value for the routes. If the preferred value in the routing policy is zero, the routes use the value set with the peer { ipv6-group-name | ipv6-address } preferred-value value command. For how to use a routing policy to set a preferred value, see the command peer ipv6-address route-policy route-policy-name { import | export } in this document, and the command apply preferred-value preferred-value in the chapter “Routing policy configuration commands.”

Examples

# Configure the preferred value as 50 for routes from peer 1:2::3:4.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family vpn-instance 11

[Sysname-bgp-ipv6-11] peer 1:2::3:4 preferred-value 50

peer public-as-only (IPv6 address family view)

Syntax

peer { ipv6-group-name | ipv6-address } public-as-only

undo peer { ipv6-group-name | ipv6-address } public-as-only

View

IPv6 address family view

Default level

2: System level

Parameters

ipv6-group-name: Name of a peer group, a string of 1 to 47 characters.

ipv6-address: IPv6 address of a peer.

Description

Use the peer public-as-only command to configure IPv6 BGP updates to a peer/peer group to not carry private AS numbers.

Use the undo peer public-as-only command to allow IPv6 BGP updates to a peer/peer group to carry private AS numbers.

By default, BGP updates carry the private AS number.

The command does not take effect if the BGP update has both the public AS number and private AS number. The range of private AS number is from 64512 to 65535.

Examples

# Configure BGP updates sent to the peer 1:2::3:4 to not carry private AS numbers.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] peer 1:2::3:4 public-as-only

peer reflect-client (IPv6 address family view)

Syntax

peer { group-name | ipv4-address | ipv6-address } reflect-client

undo peer { group-name | ipv4-address | ipv6-address } reflect-client

View

IPv6 address family view

Default level

2: System level

Parameters

group-name: Name of an IPv4 or IPv6 peer group, a string of 1 to 47 characters.

ipv4-address: IPv4 address of a peer.

ipv6-address: IPv6 address of a peer.

Description

Use the peer reflect-client command to configure the router as a route reflector and specify a peer/peer group as a client.

Use the undo peer reflect-client command to remove the configuration.

By default, neither route reflector nor client is configured.

Related commands: reflect between-clients and reflector cluster-id.

Examples

# Configure the local router as a route reflector and specify the peer group test as a client.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] group test

[Sysname-bgp-af-ipv6] peer test reflect-client

peer route-limit (IPv6 address family view)

Syntax

peer { group-name | ipv4-address | ipv6-address } route-limit prefix-number [ { alert-only | reconnect reconnect-time } | percentage ] *

undo peer { group-name | ipv4-address | ipv6-address } route-limit

View

IPv6 address family view

Default level

2: System level

Parameters

group-name: Name of an IPv4 or IPv6 peer group, a string of 1 to 47 characters.

ipv4-address: IPv4 address of a peer.

ipv6-address: IPv6 address of a peer.

prefix number: Specifies the upper limit of prefixes that can be received from the peer or peer group, in the range of 1 to 1048576. When the received prefixes from the peer/peer group reach the specified upper limit, the router will disconnect from the peer/peer group.

alert-only: When the received prefixes from the peer/peer group reach the specified upper limit, the router will display alarm messages rather than disconnect from the peer/peer group.

reconnect-time: Interval for the router to reconnect to the peer/peer group. The argument has no default. It ranges from 1 to 65535 seconds.

percentage: Specifies a percentage value. If the percentage of received routes to the upper limit reaches the value, the router will generate alarm messages. The default is 75. The value is in the range 1 to 100.

Description

Use the peer route-limit command to set the maximum number of prefixes that can be received from a peer/peer group.

Use the undo peer route-limit command to restore the default.

By default, the router has no limit on prefixes from a peer/peer group.

The router will end the peer relation when the number of address prefixes received for the peer exceeds the limit.

Examples

# Set the number of prefixes allowed to receive from the peer 1:2::3:4 to 100.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] peer 1:2::3:4 route-limit 100

peer route-policy (IPv6 address family view)

Syntax

peer { group-name | ipv4-address | ipv6-address } route-policy route-policy-name { import | export }

undo peer { group-name | ipv4-address | ipv6-address } route-policy route-policy-name { import | export }

View

IPv6 address family view

Default level

2: System level

Parameters

group-name: Name of an IPv4 or IPv6 peer group, a string of 1 to 47 characters.

ipv4-address: IPv4 address of a peer.

ipv6-address: IPv6 address of a peer.

route-policy-name: Name of a routing policy, a string of 1 to 63 characters.

import: Applies the routing policy to routes from the peer (group).

export: Applies the routing policy to routes sent to the peer (group).

Description

Use the peer route-policy command to apply a routing policy to routes incoming from or outgoing to a peer or peer group.

Use the undo peer route-policy command to remove the configuration.

By default, no routing policy is specified for the peer (group).

The peer route-policy command does not use the if-match interface clause defined in the routing policy. See the chapter “Routing policy configuration commands” for related information.

Examples

# Apply the routing policy test-policy to routes received from the peer group test.

<Sysname> system-view

[Sysname] route-policy test-policy permit node 10

[Sysname-route-policy] if-match cost 10

[Sysname-route-policy] apply cost 65535

[Sysname-route-policy] quit

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] group test external

[Sysname-bgp-af-ipv6] peer test route-policy test-policy import

peer route-policy (IPv6 BGP-VPN instance view)

Syntax

peer ipv6-address route-policy route-policy-name { export | import }

undo peer ipv6-address [ route-policy route-policy-name { export | import } ]

View

IPv6 BGP-VPN instance view

Default level

2: System level

Parameters

ipv6-address: IPv6 address of a peer.

route-policy-name: Name of a routing policy, a string of 1 to 63 characters.

import: Applies the routing policy to routes from the peer (group).

export: Applies the routing policy to routes sent to the peer (group).

Description

Use the peer route-policy command to apply a routing policy to routes incoming from or outgoing to a peer or peer group.

Use the undo peer route-policy command to remove the configuration.

By default, no routing policy is specified for the peer (group).

The peer route-policy command does not use the if-match interface clause defined in the routing policy. See the chapter “Routing policy configuration commands” for related information.

Examples

# Apply the routing policy test-policy to routes received from the peer 2001::1.

<Sysname> system-view

[Sysname] route-policy test-policy permit node 10

[Sysname-route-policy] if-match cost 10

[Sysname-route-policy] apply cost 65535

[Sysname-route-policy] quit

[Sysname] bgp 100

[Sysname-bgp] ipv6-family vpn-instance vpn1

[Sysname-bgp-ipv6-vpn1] peer 2001::1 route-policy test-policy import

peer route-update-interval (IPv6 address family view)

Syntax

peer { ipv6-group-name | ipv6-address } route-update-interval interval

undo peer { ipv6-group-name | ipv6-address } route-update-interval

View

IPv6 address family view

Default level

2: System level

Parameters

ipv6-group-name: Name of a peer group, a string of 1 to 47 characters.

ipv6-address: IPv6 address of a peer.

interval: Specifies the minimum interval for sending the same update to a peer (group) from 5 to 600 seconds.

Description

Use the peer route-update-interval command to specify the interval for sending the same update to a peer/peer group.

Use the undo peer route-update-interval command to restore the default.

By default, the interval is 15 seconds for the IBGP peer, and 30 seconds for the EBGP peer.

Examples

# Specify the interval for sending the same update to the peer 1:2::3:4 as 10 seconds.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] peer 1:2::3:4 as-number 100

[Sysname-bgp-af-ipv6] peer 1:2::3:4 route-update-interval 10

peer substitute-as (IPv6 address family view)

Syntax

peer { ipv6-group-name | ipv6-address } substitute-as

undo peer { ipv6-group-name | ipv6-address } substitute-as

View

IPv6 address family view

Default level

2: System level

Parameters

ipv6-group-name: Name of a peer group, a string of 1 to 47 characters.

ipv6-address: IPv6 address of a peer.

Description

Use the peer substitute-as command to substitute the local AS number for the AS number of a peer/peer group in the AS_PATH attribute.

Use the undo peer substitute-as command to remove the configuration.

The substitution is not configured by default.

Examples

# Substitute the local AS number for the AS number of peer 1:2::3:4.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] peer 1:2::3:4 substitute-as

peer timer (IPv6 address family view)

Syntax

peer { ipv6-group-name | ipv6-address } timer keepalive keepalive hold holdtime

undo peer { ipv6-group-name | ipv6-address } timer

View

IPv6 address family view

Default level

2: System level

Parameters

ipv6-group-name: Name of a peer group, a string of 1 to 47 characters.

ipv6-address: IPv6 address of a peer.

keepalive: Specifies the keepalive interval in seconds, ranging from 0 to 21845.

holdtime: Specifies the holdtime in seconds, whose value is 0 or in the range of 3 to 65535.

Description

Use the peer timer command to configure keepalive interval and holdtime interval for a peer or peer group.

Use the undo peer timer command to restore the default.

keepalive interval defaults to 60 seconds, and holdtime interval defaults to 180 seconds

The timers configured with this command are preferred to the timers configured with the timer command.

If the holdtime interval is configured as 0, no keepalive message will be sent to the peer, and the peer connection will never time out. If the keepalive interval is configured as 0 and the negotiated hold time is not 0, one third of the hold time is taken as the interval for sending keepalive messages.

If neither the holdtime interval nor the keepalive interval is configured as 0, the holdtime interval must be at least three times the keepalive interval.

After this command is executed, the peer connection is closed at once, and a new connection to the peer is negotiated using the configured hold time.

Related commands: timer.

Examples

# Configure the keepalive interval and holdtime interval for the peer group test as 60 seconds and 180 seconds.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] group test external

[Sysname-bgp-af-ipv6] peer test timer keepalive 60 hold 180

# Configure both the keepalive interval and holdtime interval for peer group test as 0 seconds, indicating the peer group will never time out.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] group test external

[Sysname-bgp-af-ipv6] peer test timer keepalive 0 hold 0

preference (IPv6 address family view/IPv6 BGP-VPN instance view)

Syntax

preference { external-preference internal-preference local-preference | route-policy route-policy-name }

undo preference

View

IPv6 address family view, IPv6 BGP-VPN instance view

Default level

2: System level

Parameters

external-preference: Preference of EBGP route learned from an EBGP peer, in the range 1 to 255.

internal-preference: Preference of IBGP route learned from an IBGP peer, in the range 1 to 255.

local-preference: Preference of IPv6 BGP local route, in the range 1 to 255.

route-policy-name: Routing policy name, a string of 1 to 63 characters. The routing policy can set a preference for routes passing it. The default value applies to the routes filtered out.

Description

Use the preference command to configure preferences for EBGP, IBGP, and local routes.

Use the undo preference command to restore the default.

The bigger the preference value is, the lower the preference is. The default values of external-preference, internal-preference and local-preference are 255, 255 and 130 respectively.

Examples

# Configure preferences for EBGP, IBGP, and local routes as 20, 20 and 200.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] preference 20 20 200

reflect between-clients (IPv6 address family view)

Syntax

reflect between-clients

undo reflect between-clients

View

IPv6 address family view

Default level

2: System level

Parameters

None

Description

Use the reflect between-clients command to enable route reflection between clients.

Use the undo reflect between-clients command to disable this function.

By default, route reflection between clients is enabled.

After a route reflector is configured, it reflects routes between clients. If the clients are fully meshed, H3C recommends disabling route reflection on the route reflector to reduce costs.

Related commands: reflector cluster-id and peer reflect-client.

Examples

# Enable route reflection between clients.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] reflect between-clients

reflector cluster-id (IPv6 address family view)

Syntax

reflector cluster-id cluster-id

undo reflector cluster-id

View

IPv6 address family view

Default level

2: System level

Parameters

cluster-id: Specifies the cluster ID of the route reflector, an integer from 1 to 4294967295 (the system translates it into an IPv4 address) or an IPv4 address.

Description

Use the reflector cluster-id command to configure the cluster ID of the route reflector.

Use the undo reflector cluster-id command to remove the configured cluster ID.

By default, a route reflector uses its router ID as the cluster ID.

Typically, a cluster has only one route reflector, so the router ID of the route reflector identifies the cluster. If multiple route reflectors are configured to improve the stability of the network, you should use this command to configure the identical cluster ID for all the reflectors to avoid routing loops.

Related commands: reflect between-clients and peer reflect-client.

Examples

# Set 50 as the cluster ID for the route reflector, which is one of multiple route reflectors in the cluster.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] reflector cluster-id 50

refresh bgp ipv6

Syntax

refresh bgp ipv6 { ipv4-address | ipv6-address | all | external | group group-name | internal } { export | import }

View

User view

Default level

1: Monitor level

Parameters

ipv4-address: Soft-resets the connection with an IPv4 BGP peer.

ipv6-address: Soft-resets the connection with an IPv6 BGP peer.

all: Soft-resets all IPv6 BGP connections.

external: Soft-resets EBGP connections.

group ipv6-group-name: Soft-resets connections with a peer group. The name of the peer group is a string of 1 to 47 characters.

internal: Soft-resets IBGP connections.

export: Performs soft reset in outbound direction.

import: Performs soft reset in inbound direction.

Description

Use the refresh bgp ipv6 command to soft reset specified IPv4/IPv6 BGP connections. With this feature, you can refresh the IPv4/IPv6 BGP routing table and apply a new available policy without tearing down BGP connections.

To perform IPv4/IPv6 BGP soft reset, all routers in the network should support route-refresh. If a router not supporting route refresh exists in the network, you need to use the peer keep-all-routes command on the local router to save all route updates before performing soft reset.

Examples

# Soft reset inbound IPv6 BGP connections.

<Sysname> refresh bgp ipv6 all import

reset bgp ipv6

Syntax

reset bgp ipv6 { as-number | ipv4-address | ipv6-address [ flap-info ] | all | external | group group-name | internal }

View

User view

Default level

1: Monitor level

Parameters

as-number: Resets the IPv6 BGP connections to peers in the specified AS. The AS number is in the range of 1 to 4294967295.

ipv4-address: Resets the connection to the specified IPv4 BGP peer.

ipv6-address: Resets the connection to the specified IPv6 BGP peer.

flap-info: Clears route flap information.

all: Resets all IPv6 BGP connections.

external: Resets all the EBGP connections.

group group-name: Resets the connections to the specified IPv6 BGP peer group.

internal: Resets all the IBGP connections.

Description

Use the reset bgp ipv6 command to reset specified IPv4/IPv6 BGP connections.

Examples

# Reset all the IPv6 BGP connections.

<Sysname> reset bgp ipv6 all

reset bgp ipv6 dampening

Syntax

reset bgp ipv6 dampening [ ipv6-address prefix-length ]

View

User view

Default level

1: Monitor level

Parameters

ipv6-address: IPv6 address

prefix-length: Prefix length of the address, in the range 0 to 128.

Description

Use the reset bgp ipv6 dampening command to clear dampened IPv6 BGP route information and release suppressed routes.

If no ipv6-address prefix-length is specified, all dampened IPv6 BGP route information will be cleared.

Examples

# Clear the dampened information of routes to 2345::/64 and release suppressed routes.

<Sysname> reset bgp ipv6 dampening 2345:: 64

reset bgp ipv6 flap-info

Syntax

reset bgp ipv6 flap-info [ ipv6-address/prefix-length | as-path-acl as-path-acl-number | regexp as-path-regexp ]

View

User view

Default level

1: Monitor level

Parameters

ipv6-address: Clears the flap statistics for the specified IPv6 address.

prefix-length: Prefix length of the address, in the range 1 to 128.

as-path-acl-number: Clears the flap statistics for routes matching the AS path ACL. The number is in the range 1 to 256.

as-path-regexp: Clears the flap statistics for routes matching the AS path regular expression.

Description

Use the reset bgp ipv6 flap-info command to clear IPv6 routing flap statistics.

If no parameters are specified, the flap statistics of all the routes will be cleared

Examples

# Clear the flap statistics of the routes matching AS path ACL 10.

<Sysname> system-view

[Sysname] ip as-path 10 permit ^100.*200$

[Sysname] quit

<Sysname> reset bgp ipv6 flap-info as-path-acl 10

router-id

Syntax

router-id router-id

undo router-id

View

BGP view

Default level

2: System level

Parameters

router-id: Router ID in IP address format.

Description

Use the router-id command to specify a router ID for the router.

Use the undo router-id command to remove a router ID.

To run IPv6 BGP protocol, a router must have a router ID, an unsigned 32-bit integer and the unique ID of the router in the AS.

You can specify a router ID manually. Otherwise, the system selects the highest IPv4 address among loopback interface addresses as the router ID. If no loopback interface addresses are available, the system selects the highest IPv4 address among physical interface IPv4 addresses as the router ID. Specify a loopback interface address as the router ID to enhance network reliability.

If the interface whose IPv4 address is selected as the router ID or the manual router ID is deleted, the system selects a new router ID for the router.

Examples

# Specify the router ID of the router as 10.18.4.221.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] router-id 10.18.4.221

synchronization (IPv6 address family view)

Syntax

synchronization

undo synchronization

View

IPv6 address family view

Default level

2: System level

Parameters

None

Description

Use the synchronization command to enable the synchronization between IPv6 BGP and IGP.

Use the undo synchronization command to disable the synchronization.

The feature is disabled by default.

With this feature enabled and when a non-BGP router is responsible for forwarding packets in an AS, IPv6 BGP speakers in the AS cannot advertise routing information to other ASs unless all routers in the AS know the latest routing information.

By default, upon receiving an IPv6 IBGP route, the BGP router only checks whether the next hop is reachable before advertisement. If synchronization is enabled, the IBGP route can be advertised to EBGP peers only when the route is also advertised by the IGP.

Examples

# Enable the route synchronization between IPv6 BGP and IGP.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] synchronization

timer (IPv6 address family view)

Syntax

timer keepalive keepalive hold holdtime

undo timer

View

IPv6 address family view

Default level

2: System level

Parameters

keepalive: Keepalive interval in seconds, ranging from 0 to 21845.

holdtime: Holdtime interval in seconds, whose value is 0 or in the range of 3 to 65535.

Description

Use the timer command to specify the IPv6 BGP keepalive interval and holdtime interval.

Use the undo timer command to restore the default.

By default, the keepalive and holdtime intervals are 60s and 180s respectively.

The timers configured with the peer timer command are preferred to the timers configured with the timer command.

If the holdtime interval is configured as 0, no keepalive message will be sent to the peer, and the peer connection will never time out. if the keepalive interval is configured as 0 and the negotiated hold time is not 0, one third of the hold time is taken as the interval for sending keepalive messages.

If neither the holdtime interval nor the keepalive interval is configured as 0, the holdtime interval must be at least three times the keepalive interval.

The configured timers apply to all IPv6 BGP peers, but they become valid for an IPv6 BGP peer only after the relevant IPv6 BGP connection is reset.

After this command is executed, no peer connection is closed at once. The configured hold time is used for negotiation when a peer relationship is reestablished.

Related commands: peer timer.

Examples

# Configure keepalive interval and holdtime interval as 60 and 180 seconds.

<Sysname> system-view

[Sysname] bgp 100

[Sysname-bgp] ipv6-family

[Sysname-bgp-af-ipv6] timer keepalive 60 hold 180

06-Layer 3 - IP Routing Command Reference

balance (IPv6 address family view/IPv6 BGP-VPN instance view)

bestroute as-path-neglect (IPv6 address family view)

bestroute compare-med (IPv6 address family view)

bestroute med-confederation (IPv6 address family view)

compare-different-as-med (IPv6 address family view)

dampening (IPv6 address family view)

default local-preference (IPv6 address family view/IPv6 BGP-VPN instance view)

default med (IPv6 address family view/IPv6 BGP-VPN instance view)

default-route imported (IPv6 address family view/IPv6 BGP-VPN instance view)

display bgp ipv6 routing-table

display bgp ipv6 routing-table as-path-acl

display bgp ipv6 routing-table community-list

filter-policy export (IPv6 address family view/IPv6 BGP-VPN instance view)

filter-policy import (IPv6 address family view/IPv6 BGP-VPN instance view)

group (IPv6 address family view)

import-route (IPv6 address family view/IPv6 BGP-VPN instance view)

network (IPv6 address family view/IPv6 BGP-VPN instance view)

peer advertise-community (IPv6 address family view)

peer advertise-ext-community (IPv6 address family view)

peer allow-as-loop (IPv6 address family view)

peer as-number (IPv6 address family view)

peer as-path-acl (IPv6 address family view)

peer bfd (IPv6 address family view/IPv6 BGP-VPN instance view)

peer capability-advertise orf non-standard (IPv6 address family view)

peer capability-advertise route-refresh

peer capability-advertise suppress-4-byte-as (IPv6 address family view)

peer connect-interface (IPv6 address family view)

peer ebgp-max-hop (IPv6 address family view)

peer fake-as (IPv6 address family view)

peer filter-policy (IPv6 address family view)

peer group (IPv6 address family view)

peer ignore (IPv6 address family view)

peer keep-all-routes (IPv6 address family view)

peer log-change (IPv6 address family view)

peer next-hop-local (IPv6 address family view)

peer preferred-value (IPv6 address family view)

peer public-as-only (IPv6 address family view)

peer reflect-client (IPv6 address family view)

peer route-limit (IPv6 address family view)

peer route-policy (IPv6 address family view)

peer route-update-interval (IPv6 address family view)

peer substitute-as (IPv6 address family view)

peer timer (IPv6 address family view)

preference (IPv6 address family view/IPv6 BGP-VPN instance view)

reflect between-clients (IPv6 address family view)

reflector cluster-id (IPv6 address family view)

refresh bgp ipv6

reset bgp ipv6

synchronization (IPv6 address family view)

Cloud & AI

InterConnect

Intelligent Terminal Products

Product Support Services

Technical Service Solutions

Resource Center

Policy

Online Help

Become a Partner

Partner Resources

Partner Business Management

Company Information

News & Events

Contact Us