• 产品与解决方案
  • 行业解决方案
  • 服务
  • 支持
  • 合作伙伴
  • 新华三人才研学中心
  • 关于我们

H3C E528[E552]以太网交换机 命令参考-Release 1103-6W101

08-LLDP命令

本章节下载  (175.19 KB)

docurl=/cn/Service/Document_Software/Document_Center/Switches/Catalog/E/E528[E552]/Command/Command_Manual/H3C_E528[E552]_CR-Release_1103-6W101/201108/723271_30005_0.htm

08-LLDP命令


1 LLDP配置命令

1.1  LLDP配置命令

1.1.1  display lldp local-information

【命令】

display lldp local-information [ global | interface interface-type interface-number ]

【视图】

任意视图

【缺省级别】

1:监控级

【参数】

global:显示待发送的全局LLDP信息。

interface interface-type interface-number:显示指定端口上待发送的LLDP信息,interface-type interface-number表示接口类型和接口编号。

【描述】

display lldp local-information命令用来显示待发送的LLDP信息,这些信息将被组织成TLV发送给邻居设备。

需要注意的是,如果未指定任何参数,将显示待发送的所有LLDP信息,包括全局LLDP信息以及所有使能了LLDP功能且状态为up的端口上的LLDP信息。

【举例】

# 显示所有待发送的LLDP信息。

<Sysname> display lldp local-information

Global LLDP local-information:

  Chassis ID         : 00e0-fc00-5600

  System name        : Sysname

  System description : System

  System capabilities supported : Bridge,Router

  System capabilities enabled   : Bridge,Router

 

  MED information

  Device class: Connectivity device

 

  HardwareRev               : REV.A

  FirmwareRev               : 109

  SoftwareRev               : 5.20 Alpha 2101

  SerialNum                 : NONE

  Manufacturer name         : Manufacturer

  Model name                : Model

  Asset tracking identifier : Unknown

LLDP local-information of port 1[GigabitEthernet1/0/1]:

  Port ID subtype  : Interface name

  Port ID          : GigabitEthernet1/0/1

  Port description : GigabitEthernet1/0/1 Interface

 

  Management address type           : ipv4

  Management address                : 192.168.1.11

  Management address interface type : IfIndex

  Management address interface ID   : 54

  Management address OID            : 0

 

  Port VLAN ID(PVID): 1

 

  Port and protocol VLAN ID(PPVID) : 1

  Port and protocol VLAN supported : Yes

  Port and protocol VLAN enabled   : No

 

  VLAN name of VLAN 1: VLAN 0001

 

  Auto-negotiation supported : Yes

  Auto-negotiation enabled   : Yes

  OperMau                    : speed(1000)/duplex(Full)

 

  PoE supported: No

 

  Link aggregation supported : Yes

  Link aggregation enabled   : No

  Aggregation port ID        : 0

 

  Maximum frame Size: 1536

 

  MED information

  Media policy type        : Unknown

  Unknown Policy           : Yes

  VLAN tagged              : No

  Media policy VlanID      : 0

  Media policy L2 priority : 0

  Media policy Dscp        : 0

表1-1 display lldp local-information命令显示信息描述表

字段

描述

Global LLDP local-information

待发送的全局LLDP信息

Chassis ID

Chassis ID值,为本设备的桥MAC地址

System name

系统名称

System description

系统描述

System capabilities supported

系统所支持的功能:

l      Bridge:表示支持交换功能

l      Router:表示支持路由功能

System capabilities enabled

系统已使能的功能:

l      Bridge:表示交换功能已使能

l      Router:表示路由功能已使能

MED information

MED相关信息

Device class

MED设备类型

l      Connectivity device:表示网络设备

l      Class I:表示一般终端设备,即所有需要LLDP发现服务的终端设备

l      Class II:表示媒体终端设备,即具备媒体能力的终端设备,其能力包含了一般终端设备的能力。该类设备支持媒体流

l      Class III:表示通讯终端设备,即直接支持目标用户IP通讯系统的终端设备,其能力包含了一般终端设备和媒体终端设备的所有能力。该类设备直接被目标用户所使用

HardwareRev

产品的硬件版本

FirmwareRev

产品的固件版本

SoftwareRev

产品的软件版本

SerialNum

序列号

Manufacturer name

制造厂商

Model name

模块名称

Asset tracking identifier

资产跟踪ID

LLDP local-information of port 1

端口1上待发送的LLDP信息

Port ID subtype

端口ID类型:

l      MAC address:表示MAC地址

l      Interface name:表示接口名称

Port ID

端口ID值,根据本设备的Port ID subtype取相应类型的值

Port description

端口描述

Management address type

管理地址类型

Management address

管理地址

Management address interface type

管理地址所在接口的编码方式

Management address interface ID

管理地址接口索引

Management address OID

管理地址对象标识

Port VLAN ID(PVID)

端口VLAN ID

Port and protocol VLAN ID(PPVID)

端口协议VLAN ID

Port and protocol VLAN supported

是否支持端口协议VLAN

Port and protocol VLAN enabled

是否已使能端口协议VLAN

VLAN name of VLAN 1

VLAN 1的名称

Auto-negotiation supported

端口是否支持自协商

Auto-negotiation enabled

端口是否已使能自协商

OperMau

端口自适应的速率和双工状态

PoE supported

是否支持PoE

Link aggregation supported

端口是否支持链路聚合

Link aggregation enabled

端口是否已使能链路聚合

Aggregation port ID

聚合端口的端口ID,0表示未使能链路聚合功能

Maximum frame Size

端口支持的最大帧长度

MED information

显示MED信息

Media policy type

媒体策略类型:

l      unknown:表示类型未知

l      voice:表示语音

l      voiceSignaling:表示语音信号

l      guestVoice:表示访客语音

l      guestVoiceSignaling:表示访客语音信号

l      softPhoneVoice:表示软体电话语音

l      videoconferencing:表示视频会议

l      streamingVideo:表示流视频

l      videoSignaling:表示视频信号

Unknown Policy

媒体策略类型是否未知:

l      Yes:表示策略类型未知

l      No:表示策略类型已知

VLAN tagged

媒体VLAN是否带Tag

Media Policy VlanID

媒体VLAN的VLAN ID

Media Policy L2 priority

二层优先级

Media Policy Dscp

DSCP的值

Location format

位置信息格式:

l      Invalid:表示无效位置数据类型

l      Coordinate-based LCI:表示基于坐标的位置信息

l      Civic Address LCI:表示普通地址信息

l      ECS ELIN:表示紧急电话号码

Location Information

位置信息

 

1.1.2  display lldp neighbor-information

【命令】

display lldp neighbor-information [ brief | interface interface-type interface-number [ brief ] | list [ system-name system-name ] ]

【视图】

任意视图

【缺省级别】

1:监控级

【参数】

brief:显示由邻居设备发来的LLDP信息摘要。如果未指定该参数,将显示由邻居设备发来的LLDP信息详情。

interface interface-type interface-number:显示指定端口收到的由邻居设备发来的LLDP信息,interface-type interface-number表示接口类型和接口编号。如果未指定该参数,将显示所有端口收到的由邻居设备发来的LLDP信息。

list:按列表显示由邻居设备发来的LLDP信息。

system-name system-name:按列表显示由指定邻居设备发来的LLDP信息。system-name表示邻居设备的系统名称,为1~255个字符的字符串。如果未指定该参数,将按列表显示由所有邻居设备发来的LLDP信息。

【描述】

display lldp neighbor-information命令用来显示由邻居设备发来的LLDP信息,这些信息是由邻居设备组织成TLV并发送给本设备的。

【举例】

# 显示所有端口收到的由邻居设备发来的LLDP信息。

<Sysname> display lldp neighbor-information

 

LLDP neighbor-information of port 1[GigabitEthernet1/0/1]:

  Neighbor index   : 1

  Update time      : 0 days,0 hours,1 minutes,1 seconds

  Chassis type     : MAC address

  Chassis ID       : 000f-0055-0002

  Port ID type     : Interface name

  Port ID          : GigabitEthernet1/0/1

  Port description : GigabitEthernet1/0/1 Interface

  System name        : Sysname

  System description : System

  System capabilities supported : Bridge,Router

  System capabilities enabled   : Bridge,Router

 

  Management address type           : ipv4

  Management address                : 192.168.1.55

  Management address interface type : IfIndex

  Management address interface ID   : Unknown

  Management address OID            : 0

 

  Port VLAN ID(PVID): 1

 

  Port and protocol VLAN ID(PPVID) : 1

  Port and protocol VLAN supported : Yes

  Port and protocol VLAN enabled   : No

 

  VLAN name of VLAN 1: VLAN 0001

 

  Auto-negotiation supported : Yes

  Auto-negotiation enabled   : Yes

  OperMau                    : speed(1000)/duplex(Full)

 

  Power port class          : PD

  PSE power supported       : No

  PSE power enabled         : No

  PSE pairs control ability : No

  Power pairs               : Signal

  Port power classification : Class 0

 

  Link aggregation supported : Yes

  Link aggregation enabled   : No

  Aggregation port ID        : 0

 

  Maximum frame Size: 1536

# 按列表显示所有邻居设备发来的LLDP信息。

<Sysname> display lldp neighbor-information list

 

System Name           Local Interface Chassis ID     Port ID

System1               GE1/0/1         000f-e25d-ee91 GigabitEthernet1/0/5

System2               GE1/0/2         000f-e25d-ee92 GigabitEthernet1/0/6

System3               GE1/0/3         000f-e25d-ee93 GigabitEthernet1/0/7

表1-2 display lldp neighbor-information命令显示信息描述表

字段

描述

LLDP neighbor-information of port 1

端口1上收到的LLDP信息

Neighbor index

邻居索引

Update time

邻居信息最新更新时间

Chassis type

Chassis ID类型:

l      Chassis component:表示底架组件

l      Interface alias:表示接口化名

l      Port component:表示端口组件

l      MAC address:表示MAC地址

l      Network address:表示网络地址

l      Interface name:表示接口名称

l      Locally assigned:表示本地配置

Chassis ID

Chassis ID值,根据邻居设备的Chassis type取相应类型的值

Port ID type

端口ID类型:

l      Interface alias:表示接口化名

l      Port component:表示端口组件

l      MAC address:表示MAC地址

l      Network Address:表示网络地址

l      Interface name:表示接口名称

l      Agent circuit ID:表示代理巡回标识

l      Locally assigned:表示本地配置

Port ID

端口ID值,根据邻居设备的Port ID type取相应类型的值

Port description

端口描述

System name

系统名称

System description

系统描述

System capabilities supported

系统所支持的功能:

l      Repeater:表示支持转发功能

l      Bridge:表示支持交换功能

l      Router:表示支持路由功能

System capabilities enabled

系统已使能的功能:

l      Repeater:表示转发功能已使能

l      Bridge:表示交换功能已使能

l      Router:表示路由功能已使能

Management address type

管理地址类型

Management address

管理地址

Management address interface type

管理地址接口类型

Management address interface ID

管理地址接口索引

Management address OID

管理地址对象标识

Port VLAN ID

端口VLAN ID

Port and protocol VLAN ID(PPVID)

端口协议VLAN ID

Port and protocol VLAN supported

是否支持端口协议VLAN

Port and protocol VLAN enabled

是否使能端口协议VLAN

VLAN name of VLAN 1

VLAN 1的名称

Auto-negotiation supported

端口是否支持自协商

Auto-negotiation enabled

端口是否已使能自协商

OperMau

端口自适应的速率和双工状态

Power port class

PoE类型:

l      PSE:表示供电设备(Power Sourcing Entity)

l      PD:表示受电设备(Power Device)

PSE power supported

是否支持PSE供电

PSE power enabled

是否已使能PSE供电

PSE pairs control ability

供电方式是否可控

Power pairs

PoE端口的远程供电模式:

l      Signal:表示信号线供电模式

l      Spare:表示空闲线供电模式

Port power classification

PD的端口控制级别:

l      Class0:表示级别0

l      Class1:表示级别1

l      Class2:表示级别2

l      Class3:表示级别3

l      Class4:表示级别4

Link aggregation supported

端口是否支持链路聚合

Link aggregation enabled

端口是否已使能链路聚合

Aggregation port ID

聚合端口的端口ID,0表示未使能链路聚合功能

Maximum frame Size

端口支持的最大帧长度

Location format

位置信息格式:

l      Invalid:表示无效位置数据类型

l      Coordinate-based LCI:表示基于坐标的位置信息

l      Civic Address LCI:表示普通地址信息

l      ECS ELIN:表示紧急电话号码

Location Information

位置信息

PoE PSE power source

PSE所采用的电源类型:

l      Primary:表示采用主用电源作为电源

l      Backup:表示采用备用电源作为电源

PoE service type

PoE服务类型

Port PSE Priority

PSE上端口的供电优先级:

l      Unknown:表示优先级未知

l      Critical:表示优先级为1级

l      High:表示优先级为2级

l      Low:表示优先级为3级

Port available power value

PSE上端口可提供的功率(单位为瓦特)

Unknown basic TLV

未知的基本TLV

TLV type

未知的基本TLV类型

TLV information

未知的基本TLV的具体信息

Unknown organizationally-defined TLV

未知组织定义TLV

TLV OUI

未知组织定义TLV的对象唯一标识

TLV subtype

未知的组织定义TLV类型

Index

未知组织的索引

TLV information

未知组织定义TLV的具体信息

Local Interface

接收LLDP信息的本端端口

 

1.1.3  display lldp statistics

【命令】

display lldp statistics [ global | interface interface-type interface-number ]

【视图】

任意视图

【缺省级别】

1:监控级

【参数】

global:显示全局LLDP统计信息。

interface interface-type interface-number:显示指定端口上的LLDP统计信息,interface-type interface-number表示接口类型和接口编号。

【描述】

display lldp statistics命令用来显示LLDP的统计信息。

需要注意的是,如果未指定任何参数,将同时显示全局和端口上的LLDP统计信息。

【举例】

# 显示全局和端口上的LLDP统计信息。

<Sysname> display lldp statistics

LLDP statistics global Information:

LLDP neighbor information last change time:0 days,0 hours,4 minutes,40 seconds

The number of LLDP neighbor information inserted : 1

The number of LLDP neighbor information deleted  : 1

The number of LLDP neighbor information dropped  : 0

The number of LLDP neighbor information aged out : 1

 

LLDP statistics information of port 1 [GigabitEthernet1/0/1]:

The number of LLDP frames transmitted            : 0

The number of LLDP frames received               : 0

The number of LLDP frames discarded              : 0

The number of LLDP error frames                  : 0

The number of LLDP TLVs discarded                : 0

The number of LLDP TLVs unrecognized             : 0

The number of LLDP neighbor information aged out : 0

The number of CDP frames transmitted             : 0

The number of CDP frames received                : 0

The number of CDP frames discarded               : 0

The number of CDP error frames                   : 0

表1-3 display lldp statistics命令显示信息描述表

字段

描述

LLDP statistics global information

全局LLDP统计信息

LLDP neighbor information last change time

邻居信息的最后更新时间

The number of LLDP neighbor information inserted

邻居信息的增加次数

The number of LLDP neighbor information deleted

邻居信息的删除次数

The number of LLDP neighbor information dropped

由于空间不足而导致丢弃邻居信息的次数

The number of LLDP neighbor information aged out

邻居信息的老化数量

LLDP statistics information of port 1

端口1上的LLDP统计信息

The number of LLDP frames transmitted

发送的LLDP帧总数

The number of LLDP frames received

收到的LLDP帧总数

The number of LLDP frames discarded

丢弃的LLDP帧总数

The number of LLDP error frames

收到的错误LLDP帧总数

The number of LLDP TLVs discarded

丢弃的LLDP TLV总数

The number of LLDP TLVs unrecognized

不可识别的LLDP TLV总数

The number of LLDP neighbor information aged out

老化的LLDP邻居信息总数

The number of CDP frames transmitted

发送的CDP帧总数

The number of CDP frames received

收到的CDP帧总数

The number of CDP frames discarded

丢弃的CDP帧总数

The number of CDP error frames

收到的错误CDP帧总数

 

1.1.4  display lldp status

【命令】

display lldp status [ interface interface-type interface-number ]

【视图】

任意视图

【缺省级别】

1:监控级

【参数】

interface interface-type interface-number:显示指定端口上的LLDP状态信息,interface-type interface-number表示接口类型和接口编号。如果未指定该参数,将显示所有端口上的LLDP状态信息。

【描述】

display lldp status命令用来显示LLDP的状态信息。

【举例】

# 显示全局和所有端口上的LLDP状态信息。

<Sysname> display lldp status

Global status of LLDP: Enable

The current number of LLDP neighbors: 0

The current number of CDP neighbors: 0

LLDP neighbor information last changed time: 0 days,0 hours,4 minutes,40 seconds

Transmit interval              : 30s

Hold multiplier                : 4

Reinit delay                   : 2s

Transmit delay                 : 2s

Trap interval                  : 5s

Fast start times               : 3

 

Port 1 [GigabitEthernet1/0/1]:

Port status of LLDP            : Enable

Admin status                   : Tx_Rx

Trap flag                      : No

Polling interval               : 0s

 

Number of neighbors:             5

Number of MED neighbors        : 2

Number of CDP neighbors        : 0

Number of sent optional TLV    : 12

Number of received unknown TLV : 5

表1-4 display lldp status命令显示信息描述表

字段

描述

Global status of LLDP

LLDP功能是否已全局使能

The current number of LLDP neighbors

当前设备的LLDP邻居总数

The current number of CDP neighbors

当前设备的CDP邻居总数

LLDP neighbor information last changed time

邻居信息的最后更新时间

Transmit interval

LLDP报文的发送时间间隔

Hold multiplier

TTL乘数

Reinit delay

端口初始化延迟时间

Transmit delay

LLDP报文的发送延迟时间

Trap interval

Trap信息的发送时间间隔

Fast start times

快速发送LLDP报文的个数

Port 1

端口1上的LLDP状态信息

Port status of LLDP

LLDP功能是否已在端口上使能

Admin status

端口LLDP工作模式:

l      Tx_Rx:表示既发送也接收LLDP报文

l      Rx_Only:表示只接收不发送LLDP报文

l      Tx_Only:表示只发送不接收LLDP报文

l      Disable:表示既不发送也不接收LLDP报文

Trap Flag

Trap功能是否已使能

Polling interval

轮询时间间隔的值,0表示轮询功能处于关闭状态

Number of neighbors

端口LLDP邻居数量

Number of MED neighbors

端口MED邻居设备的数量

Number of CDP neighbors

端口CDP邻居设备的数量

Number of sent optional TLV

端口在一个LLDP报文中发送的可选TLV总数

Number of received unknown TLV

端口在一个LLDP报文中收到的不能识别的TLV总数

 

1.1.5  display lldp tlv-config

【命令】

display lldp tlv-config [ interface interface-type interface-number ]

【视图】

任意视图

【缺省级别】

1:监控级

【参数】

interface interface-type interface-number:显示指定端口上可发送的可选TLV信息,interface-type interface-number表示接口类型和接口编号。如果未指定该参数,将显示所有端口上可发送的可选TLV信息。

【描述】

display lldp tlv-config命令用来显示端口上可发送的可选TLV信息。

【举例】

# 显示所有端口上可发送的可选TLV信息。

<Sysname> display lldp tlv-config

LLDP tlv-config of port 1[GigabitEthernet1/0/1]:

NAME                              STATUS    DEFAULT

Basic optional TLV:

Port Description TLV              YES       YES

System Name TLV                   YES       YES

System Description TLV            YES       YES

System Capabilities TLV           YES       YES

Management Address TLV            YES       YES

 

IEEE 802.1 extend TLV:

Port VLAN ID TLV                  YES       YES

Port And Protocol VLAN ID TLV     YES       YES

VLAN Name TLV                     YES       YES

 

IEEE 802.3 extend TLV:

MAC-Physic TLV                    YES       YES

Power via MDI TLV                 YES       YES

Link Aggregation TLV              YES       YES

Maximum Frame Size TLV            YES       YES

 

LLDP-MED extend TLV:

Capabilities TLV                  YES        YES

Network Policy TLV                YES        YES

Location Identification TLV       NO         NO

Extended Power via MDI TLV        YES        YES

Inventory TLV                     YES        YES

表1-5 display lldp tlv-config命令显示信息描述表

字段

描述

LLDP tlv-config of port 1

端口1上可发送的可选TLV类型

NAME

TLV类型

STATUS

端口是否配置发布指定类型TLV

DEFAULT

端口发布指定类型TLV的缺省情况

Basic optional TLV

端口可以发送的基本TLV类型

Port Description TLV

端口描述TLV

System Name TLV

系统名称TLV

System Description TLV

系统描述TLV

System Capabilities TLV

系统能力集TLV

Management Address TLV

管理地址TLV

IEEE 802.1 extended TLV

端口可发送的IEEE 802.1组织定义的TLV类型

Port VLAN ID TLV

端口VLAN ID TLV

Port And Protocol VLAN ID TLV

协议VLAN ID TLV

VLAN Name TLV

VLAN名称TLV

IEEE 802.3 extended TLV

端口可发送的IEEE 802.3组织定义的TLV类型

MAC-Physic TLV

端口物理属性TLV

Power via MDI TLV

供电能力TLV

Link Aggregation TLV

链路聚合TLV

Maximum Frame Size TLV

最大帧长度TLV

LLDP-MED extend TLV

LLDP-MED TLV

Capabilities TLV

MED能力集TLV

Network Policy TLV

网络策略TLV

Location Identification TLV

位置标识TLV

Extended Power via MDI TLV

扩展供电能力TLV

Inventory TLV

资产信息TLV,包括7种类型:

l      Hardware Revision TLV

l      Firmware Revision TLV

l      Software Revision TLV

l      Serial Number TLV

l      Manufacturer Name TLV

l      Model name TLV

l      Asset id TLV

 

1.1.6  lldp admin-status

【命令】

lldp admin-status { disable | rx | tx | txrx }

undo lldp admin-status

【视图】

以太网端口视图/端口组视图

【缺省级别】

2:系统级

【参数】

disable:表示工作模式为Disable,既不发送也不接收LLDP报文。

rx:表示工作模式为Rx,只接收不发送LLDP报文。

tx:表示工作模式为Tx,只发送不接收LLDP报文。

txrx:表示工作模式为TxRx,既发送也接收LLDP报文。

【描述】

lldp admin-status命令用来配置LLDP的工作模式。undo lldp admin-status命令用来恢复缺省情况。

缺省情况下,LLDP的工作模式为TxRx,既发送也接收LLDP报文。

【举例】

# 配置端口GigabitEthernet1/0/1上LLDP的工作模式为Rx。

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] lldp admin-status rx

1.1.7  lldp check-change-interval

【命令】

lldp check-change-interval interval

undo lldp check-change-interval

【视图】

以太网端口视图/端口组视图

【缺省级别】

2:系统级

【参数】

interval:表示轮询时间间隔,取值范围为1~30,单位为秒。

【描述】

lldp check-change-interval命令用来使能轮询功能并配置轮询时间间隔。undo lldp check-change-interval命令用来关闭轮询功能。

缺省情况下,轮询功能处于关闭状态。

【举例】

# 在端口GigabitEthernet1/0/1上使能轮询功能,并配置轮询时间间隔为30秒。

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] lldp check-change-interval 30

1.1.8  lldp compliance admin-status cdp

【命令】

lldp compliance admin-status cdp { disable | txrx }

【视图】

以太网端口视图/端口组视图

【缺省级别】

2:系统级

【参数】

disable:表示工作模式为Disable,既不发送也不接收CDP报文。

txrx:表示工作模式为TxRx,既发送也接收CDP报文。

【描述】

lldp compliance admin-status cdp用来配置LLDP兼容CDP功能的工作模式。

缺省情况下,LLDP兼容CDP功能的工作模式为Disable,既不发送也不接收CDP报文。

需要注意的是,欲使LLDP兼容CDP的功能生效,必须先使能LLDP兼容CDP功能,同时将LLDP兼容CDP功能的工作模式配置为TxRx。

相关配置可参考命令lldp compliance cdp

【举例】

# 在端口GigabitEthernet1/0/1上配置LLDP兼容CDP功能的工作模式为TxRx。

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] lldp compliance admin-status cdp txrx

1.1.9  lldp compliance cdp

【命令】

lldp compliance cdp

undo lldp compliance cdp

【视图】

系统视图

【缺省级别】

2:系统级

【参数】

【描述】

lldp compliance cdp命令用来使能LLDP兼容CDP功能。undo lldp compliance cdp命令用来恢复缺省情况。

缺省情况下,LLDP兼容CDP功能处于关闭状态。

需要注意的是,由于CDP报文所携Time To Live TLV中TTL的最大值为255,而TTL=Min(65535,(TTL乘数×发送LLDP报文的时间间隔)),因此为保证LLDP兼容CDP功能的正常运行,应确保该乘积不大于255。

相关配置可参考命令lldp hold-multiplierlldp timer tx-interval

【举例】

# 使能LLDP兼容CDP功能。

<Sysname> system-view

[Sysname] lldp compliance cdp

1.1.10  lldp enable

【命令】

lldp enable

undo lldp enable

【视图】

系统视图/以太网端口视图/端口组视图

【缺省级别】

2:系统级

【参数】

【描述】

lldp enable命令用来使能LLDP功能。undo lldp enable命令用来关闭LLDP功能。

缺省情况下,LLDP功能处于全局关闭状态,而在端口上处于使能状态。

需要注意的是,LLDP功能必须在全局和端口上同时使能后才能生效。

【举例】

# 在端口GigabitEthernet1/0/1上关闭LLDP功能。

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] undo lldp enable

1.1.11  lldp encapsulation snap

【命令】

lldp encapsulation snap

undo lldp encapsulation

【视图】

以太网端口视图/端口组视图

【缺省级别】

2:系统级

【参数】

【描述】

lldp encapsulation snap命令用来配置LLDP报文的封装格式为SNAP格式。undo lldp encapsulation命令用来恢复缺省情况。

缺省情况下,LLDP报文的封装格式为Ethernet II格式。

需要注意的是,LLDP CDP报文的封装格式只能为SNAP格式,不能为Ethernet II格式。

【举例】

# 配置端口GigabitEthernet1/0/1上发送的LLDP报文的封装格式为SNAP格式。

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] lldp encapsulation snap

1.1.12  lldp fast-count

【命令】

lldp fast-count count

undo lldp fast-count

【视图】

系统视图

【缺省级别】

2:系统级

【参数】

count:表示快速发送LLDP报文的个数,取值范围为1~10,单位为个。

【描述】

lldp fast-count命令用来配置快速发送LLDP报文的个数。undo lldp fast-count命令用来恢复缺省情况。

缺省情况下,快速发送LLDP报文的个数为3个。

【举例】

# 配置快速发送LLDP报文的个数为4个。

<Sysname> system-view

[Sysname] lldp fast-count 4

1.1.13  lldp hold-multiplier

【命令】

lldp hold-multiplier value

undo lldp hold-multiplier

【视图】

系统视图

【缺省级别】

2:系统级

【参数】

value:表示TTL乘数,取值范围为2~10。

【描述】

lldp hold-multiplier命令用来配置TTL乘数。undo lldp hold-multiplier命令用来恢复缺省情况。

缺省情况下,TTL乘数为4。

需要注意的是,LLDP报文所携Time To Live TLV中TTL的值用来设置邻居信息在本地设备上的老化时间,由于TTL=Min(65535,(TTL乘数×发送LLDP报文的时间间隔)),即取65535与(TTL乘数×发送LLDP报文的时间间隔)中的最小值,因此通过调整TTL乘数可以控制本设备信息在邻居设备上的老化时间。

相关配置可参考命令lldp timer tx-interval

【举例】

# 配置TTL乘数为6。

<Sysname> system-view

[Sysname] lldp hold-multiplier 6

1.1.14  lldp management-address-format string

【命令】

lldp management-address-format string

undo lldp management-address-format

【视图】

以太网端口视图/端口组视图

【缺省级别】

2:系统级

【参数】

【描述】

lldp management-address-format string命令用来配置管理地址在TLV中的封装格式为字符串格式。undo lldp management-address-format命令用来恢复缺省情况。

缺省情况下,管理地址在TLV中的封装格式为数字格式。

【举例】

# 在端口GigabitEthernet1/0/1上配置管理地址在TLV中的封装格式为字符串格式。

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] lldp management-address-format string

1.1.15  lldp management-address-tlv

【命令】

lldp management-address-tlv [ ip-address ]

undo lldp management-address-tlv

【视图】

以太网端口视图/端口组视图

【缺省级别】

2:系统级

【参数】

ip-address:表示在LLDP报文中发布的管理地址。

【描述】

lldp management-address-tlv命令用来配置在LLDP报文中发布管理地址。undo lldp management-address-tlv命令用来取消在LLDP报文中发布管理地址。

缺省情况下,设备在LLDP报文中发布管理地址,发布的管理地址为端口允许通过的最小VLAN的主IP地址,若该VLAN未配置主IP地址,则为127.0.0.1。

需要注意的是,每个LLDP报文中只能携带一个管理地址TLV,若重复配置,只发送最新配置的管理地址。

【举例】

# 在端口GigabitEthernet1/0/1上配置在LLDP报文中发布的管理地址为192.6.0.1。

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] lldp management-address-tlv 192.6.0.1

1.1.16  lldp notification remote-change enable

【命令】

lldp notification remote-change enable

undo lldp notification remote-change enable

【视图】

以太网端口视图/端口组视图

【缺省级别】

2:系统级

【参数】

【描述】

lldp notification remote-change enable命令用来使能LLDP Trap功能。undo lldp notification remote-change enable命令用来恢复缺省情况。

缺省情况下,LLDP Trap功能处于关闭状态。

【举例】

# 在端口GigabitEthernet1/0/1上使能LLDP Trap功能。

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] lldp notification remote-change enable

1.1.17  lldp timer notification-interval

【命令】

lldp timer notification-interval interval

undo lldp timer notification-interval

【视图】

系统视图

【缺省级别】

2:系统级

【参数】

interval:表示发送LLDP Trap信息的时间间隔,取值范围为5~3600,单位为秒。

【描述】

lldp timer notification-interval命令用来配置发送LLDP Trap信息的时间间隔。undo lldp timer notification-interval命令用来恢复缺省情况。

缺省情况下,发送LLDP Trap信息的时间间隔为5秒。

【举例】

# 配置发送LLDP Trap信息的时间间隔为8秒。

<Sysname> system-view

[Sysname] lldp timer notification-interval 8

1.1.18  lldp timer reinit-delay

【命令】

lldp timer reinit-delay delay

undo lldp timer reinit-delay

【视图】

系统视图

【缺省级别】

2:系统级

【参数】

delay:端口初始化的延迟时间,取值范围为1~10,单位为秒。

【描述】

lldp timer reinit-delay命令用来配置端口初始化的延迟时间。undo lldp timer reinit-delay命令用来恢复缺省情况。

缺省情况下,端口初始化的延迟时间为2秒。

【举例】

# 配置端口初始化的延迟时间为4秒。

<Sysname> system-view

[Sysname] lldp timer reinit-delay 4

1.1.19  lldp timer tx-delay

【命令】

lldp timer tx-delay delay

undo lldp timer tx-delay

【视图】

系统视图

【缺省级别】

2:系统级

【参数】

delay:表示发送LLDP报文的延迟时间,取值范围为1~8192,单位为秒。

【描述】

lldp timer tx-delay命令用来配置发送LLDP报文的延迟时间。undo lldp timer tx-delay命令用来恢复缺省情况。

缺省情况下,发送LLDP报文的延迟时间为2秒。

【举例】

# 配置发送LLDP报文的延迟时间为4秒。

<Sysname> system-view

[Sysname] lldp timer tx-delay 4

1.1.20  lldp timer tx-interval

【命令】

lldp timer tx-interval interval

undo lldp timer tx-interval

【视图】

系统视图

【缺省级别】

2:系统级

【参数】

interval:表示发送LLDP报文的时间间隔,取值范围为5~32768,单位为秒。

【描述】

lldp timer tx-interval命令用来配置发送LLDP报文的时间间隔。undo lldp timer tx-interval命令用来恢复缺省情况。

缺省情况下,发送LLDP报文的时间间隔为30秒。

【举例】

# 配置发送LLDP报文的时间间隔为20秒。

<Sysname> system-view

[Sysname] lldp timer tx-interval 20

1.1.21  lldp tlv-enable

【命令】

lldp tlv-enable { basic-tlv { all | port-description | system-capability | system-description | system-name } | dot1-tlv { all | port-vlan-id | protocol-vlan-id [ vlan-id ] | vlan-name [ vlan-id ] } | dot3-tlv { all | link-aggregation | mac-physic | max-frame-size | power } | med-tlv { all | capability | inventory | location-id { civic-address device-type country-code { ca-type ca-value }&<1-10> | elin-address tel-number } | network-policy | power-over-ethernet } }

undo lldp tlv-enable { basic-tlv { all | port-description | system-capability | system-description | system-name } | dot1-tlv { all | port-vlan-id | protocol-vlan-id | vlan-name } | dot3-tlv { all | link-aggregation | mac-physic | max-frame-size | power } | med-tlv { all | capability | inventory | location-id | network-policy | power-over-ethernet } }

【视图】

以太网端口视图/端口组视图

【缺省级别】

2:系统级

【参数】

all:当指定basic-tlvdot1-tlvdot3-tlv时,表示该类型下所有的可选TLV;当指定med-tlv时,则表示该类型下除location-id以外的所有可选TLV。

basic-tlv:表示基本类型TLV。

port-description:表示Port Description TLV。

system-capability:表示System Capabilities TLV。

system-description:表示System Description TLV。

system-name:表示System Name TLV。

dot1-tlv:表示IEEE 802.1组织定义的TLV。

port-vlan-id:表示Port VLAN ID TLV。

protocol-vlan-id:表示Port And Protocol VLAN ID TLV。

vlan-name:表示VLAN Name TLV。

vlan-id:指定要发布VLAN的VLAN ID,取值范围为1~4094。如果未指定该参数,则表示发布端口所属最小VLAN的VLAN ID。

dot3-tlv:表示IEEE 802.3组织定义的TLV。

link-aggregation:表示Link Aggregation TLV。

mac-physic:表示MAC/PHY Configuration/Status TLV。

max-frame-size:表示Maximum Frame Size TLV。

power:表示Power Via MDI TLV。

med-tlv:表示LLDP-MED TLV。

capability:表示LLDP-MED Capabilities TLV。

inventory:表示Hardware Revision TLV、Firmware Revision TLV、Software Revision TLV、Serial Number TLV、Manufacturer Name TLV、Model Name TLV和Asset ID TLV。

location-id:表示Location Identification TLV

civic-address:表示Location Identification TLV封装网络设备的普通地址信息。

device-type:表示设备类型,取值范围为02。0表示设备类型为DHCP server,1表示设备类型为Switch,2表示设备类型为LLDP-MED Endpoint。

country-code:表示国家编码,取值范围请参考ISO 3166。

{ ca-type ca-value }&<1-10>:地址信息。ca-type表示地址信息类型,取值范围为0~255;ca-value表示地址信息,为1~250个字符的字符串。&<1-10>表示前面的参数最多可以输入10次。

elin-address:Location Identification TLV封装紧急电话号码。

tel-number:表示紧急电话号码,为10~25个字符的字符串。

network-policy:表示Network Policy TLV。

power-over-ethernet:表示Extended Power-via-MDI TLV。

【描述】

lldp tlv-enable命令用来配置端口上允许发布的TLV类型。undo lldp tlv-enable命令用来配置端口上禁止发布的TLV类型。

缺省情况下,端口上允许发布除Location Identification TLV之外所有类型的TLV。

需要注意的是:

l              必须先允许发布LLDP-MED Capabilities TLV,才能允许发布LLDP-MED其它类型的TLV;必须先禁止发布LLDP-MED其它类型的TLV,才能禁止发布LLDP-MED Capabilities TLV;必须先禁止发布LLDP-MED Capabilities TLV,才能禁止发布MAC/PHY Configuration/Status TLV。

l              当允许发布LLDP-MED Capabilities TLV之后,MAC/PHY Configuration/Status TLV也将自动发布。

l              在使用该命令时若不指定all参数,每次只能配置某类型下的一种可选TLV,此时可通过多次使用该命令来配置各类型下的多种可选TLV。

【举例】

# 配置端口GigabitEthernet1/0/1上允许发布IEEE 802.3组织定义的Link Aggregation可选TLV。

<Sysname> system-view

[Sysname] interface gigabitethernet 1/0/1

[Sysname-GigabitEthernet1/0/1] lldp tlv-enable dot3-tlv link-aggregation

不同款型规格的资料略有差异, 详细信息请向具体销售和400咨询。H3C保留在没有任何通知或提示的情况下对资料内容进行修改的权利!

新华三官网
联系我们