• 产品与解决方案
  • 行业解决方案
  • 服务
  • 支持
  • 合作伙伴
  • 关于我们

H3C S9500E系列 LSRM1WCM2A1 单板手册-APW100

手册下载

99-整本手册.pdf  (2.2 MB)

  • 发布时间:2009/3/3 17:32:37
  • 浏览量:
  • 下载量:

Access Controller Module无线控制业务板-LSRM1WCM2A1

业务板标识

业务板的面板右上角标有丝印:LSR1WCM2A1,用来标识该业务板。业务板的外观如1所示。

1 LSRM1WCM2A1无线控制业务板外观图

 

业务板简介

LSRM1WCM2A1无线控制业务板能够S9500E系列交换机提供无线特性。业务板的面板和接口示意图如2所示。

2 LSRM1WCM2A1无线控制业务板前面板

(1): 松不脱螺丝

(2): 拉手条

(3): 1USB接口1

(4): 2USB接口2

(5): MGMNT10/100/1000Base-T带外管理以太网接口

(6): LINK10/100/1000 Base-T带外管理以太网接口连接指示灯

(7): ACT10/100/1000 Base-T带外管理以太网接口收发指示灯

(8): CONSOLEConsole

 

1 无线控制业务板属性

属性

规格

CPU主频

600MHz

CF卡容量

256MB

内存容量

1GB

业务板尺寸(长×宽×高)

366.7mm×340mm×40.6mm

功耗

80W105W

重量

3.58kg

对外接口

l      2USB 口(支持USB1.1

l      110/100/1000Base-T以太网管理口

l      1Console

工作环境温度

045

工作环境相对湿度(非凝露)

10%95%

适用主机

S9505E/S9508E-V/S9512E

业务板适用的主机软件版本

S9500E-CMW520-A1132及以上版本

 

安装与拆卸方式

在整个安装、拆卸过程中请注意手部不要接触单板元器件,建议佩戴良好接地的防静电手环并戴上防静电手套后再进行安装操作。

 

LSRM1WCM2A1无线控制业务板支持热插拔。

 

LSRM1WCM2A1无线控制业务板的安装

LSRM1WCM2A1无线控制业务板的安装请按照下面步骤进行:

第一步:操作者正对交换机的前面板。

第二步:选择安装业务板的插槽,并拆卸插槽上的假面板。

第三步:将业务板沿着插槽导轨,缓慢的推进,直到底部的导向销套到背板的导向柱上,然后将拉手条用力向内扣合。

第四步:用十字螺丝刀对准业务板的松不脱螺丝,并顺时针方向旋转,直至拧紧。

3 安装LSRM1WCM2A1无线控制业务板

(1): LSRM1WCM2A1无线控制业务板沿着插槽导轨缓慢推入,直到底部的导向销套到背板的导向柱上

(2): 将拉手条用力向内扣合

 

LSRM1WCM2A1无线控制业务板的拆卸

LSRM1WCM2A1无线控制业务板的拆卸请按照下面步骤进行:

第一步:操作者正对交换机的前面板。

第二步:用十字螺丝刀对准待拆卸的业务板上的松不脱螺丝,并逆时针方向旋转,直至松不脱螺丝的弹簧完全弹开。

第三步:双手分别捏住业务板上的拉手条,用力向外掰开,然后将业务板沿着插槽导轨,缓慢地拉出业务板插槽,直到完全脱离插槽为止。

升级方式

LSRM1WCM2A1无线控制业务板采用自己独立的Boot ROM程序和应用程序,其Boot菜单与S9500E交换机的Boot菜单不同。用户可通过以下方式对LSRM1WCM2A1无线控制业务板的应用程序进行升级:

(1)        通过Boot菜单本地升级

l              通过LSRM1WCM2A1无线控制业务板的Console口利用XModem协议进行升级

l              通过LSRM1WCM2A1无线控制业务板的10/100/1000Base-T以太网口利用TFTP协议进行升级

(2)        通过命令行远程升级

l              通过LSRM1WCM2A1无线控制业务板的10/100/1000Base-T以太网利用FTP协议进行升级

l              通过LSRM1WCM2A1无线控制业务板的10/100/1000Base-T以太网口利用TFTP协议进行升级

用户可以通过LSRM1WCM2A1无线控制业务板的Console口或者以太网口完成软件升级,具体方法可参见《H3C 无线控制业务板 软件升级手册》。

 

注意事项

l              如主机软件版本不匹配,请联系该设备的销售商或集成商获取相应的主机软件版本;

l              主机软件版本的升级方法请参见《H3C S9500E系列路由交换机 安装手册》相关章节。

l              单板种类或规格可能随产品版本的变更而改变,请从公司网站http://www.h3c.com.cn主页上的[服务支持/文档中心]获取最新资料。

 

 

 

Copyright © 2009 杭州华三通信技术有限公司


Access Controller Module LSRM1WCM2A1

1  Appearance

The silkscreen LSR1WCM2A1 is printed at the upper right corner of the front panel, which is used to identify the module. The following figure depicts the appearance of the module.

Figure 1 Appearance of the LSRM1WCM2A1

 

2  Specifications

The LSRM1WCM2A1 can provide wireless services to S9500E series switches. The following figure depicts the front panel of the LSRM1WCM2A1.

Figure 2 Front panel of the LSRM1WCM2A1

(1) Captive screw

(2) Ejector lever

(3) USB interface 1

(4) USB interface 2

(5) 10/100/1000Base-T out-of-band management Ethernet port (MGMNT)

(6) 10/100/1000Base-T out-of-band management Ethernet port status LED (LINK)

(7) 10/100/1000Base-T out-of-band management Ethernet port status LED (ACT)

(8) Console port (CONSOLE)

 

Table1 LSRM1WCM2A1 specifications

Item

Specification

CPU frequency

600 MHz

CF card

256 MB

Capacity

1 GB DDRII

Dimensions (H × W × D)

40.6 × 366.7 × 340 mm (1.60 × 14.44 × 13.39 in.)

Power consumption

80 W to 105 W

Weight

3.58 kg (7.89 lb)

Interface

l      Two USB interfaces (USB 1.1-compliant)

l      One 10/100/1000Base-T management Ethernet port

l      One console port

Operating temperature

0°C to 45°C (32°F to 113°F)

Operating humidity (noncondensing)

10% to 95%

Applicable device model

S9505E/S9508E-V/S9512E

Applicable host software version

S9500E-CMW520-A1132 or later versions

 

3  Installing and Removing the LSRM1WCM2A1

 

Avoid touching any components on the module during the installation or removal process. It is recommended to wear an ESD-preventive wrist strap and ESD-preventive gloves before installation.

 

The LSRM1WCM2A1 is hot swappable.

 

Installing the LSRM1WCM2A1

(1)          Face the front panel of the switch.

(2)          Choose an empty slot and remove the filler panel.

(3)          Push the access controller module into the slot along the guide rails until the positioning hole of the module is seated onto the positioning pin on the backplane.

(4)          Push the ejector levers inward to lock the access controller module in place.

(5)          Fasten the captive screws on the access controller module with a Philips screwdriver.

Figure 3 Installing the LSRM1WCM2A1

(1) Push the access controller module into the slot along the guide rails until the positioning hole of the module is seated onto the positioning pin on the backplane.

(2) Push the ejector levers inward to lock the access controller module in place.

 

Removing the LSRM1WCM2A1

(1)          Face the front panel of the switch.

(2)          Loosen the captive screws on the access controller module with a Philips screwdriver until all spring pressure is released.

(3)          Hold the ejector levers of the access controller module and push them outward.

(4)          Gently pull the access controller module out of the slot along the guide rails.

4  Upgrading the LSRM1WCM2A1

The LSRM1WCM2A1 has its own Boot ROM program and application program with a Boot ROM menu different from that of the S9500E series switches. To update the application program of the LSRM1WCM2A1, use one of the following ways:

(1)          Local update through the Boot ROM menu

l              Use the XMODEM protocol through the console port of the LSRM1WCM2A1

l              Use the TFTP protocol through the 10/100/1000Base-T Ethernet port of the LSRM1WCM2A1

(2)          Remote update through CLI

l              Use the FTP protocol through the 10/100/1000Base-T Ethernet port of the LSRM1WCM2A1

l              Use the TFTP protocol through the 10/100/1000Base-T Ethernet port of the LSRM1WCM2A1

 

You can upgrade the LSRM1WCM2A1 through its console port or Ethernet port. For details, refer to H3C Access Controller Module  Software Maintenance Manual.

 

5  Guidelines

l              If the host software version does not match the access controller module, contact the sales agent or the integrator for the right version.

l              For how to upgrade the host software version, refer to the related part in H3C S9500E Series Routing Switches  Installation Manual.

l              The types and specifications of the access controller modules may vary with product versions. For the latest documentation, go to Technical Support & Document > Technical Documents on H3C's website at http://www.h3c.com.

 

Copyright © 2009 Hangzhou H3C Technologies Co., Ltd.

 

 

 

新华三官网
联系我们