• 产品与解决方案
  • 行业解决方案
  • 服务
  • 支持
  • 合作伙伴
  • 关于我们

H3C POE DIMM条安装说明书(V1.02)

手册下载

整本手册.pdf  (1.47 MB)

  • 发布时间:2007/11/24 23:29:28
  • 浏览量:
  • 下载量:

PoE DIMM条安装说明书

1.1  规格说明

PoE DIMM条的规格说明请参见1-1

1-1 PoE DIMM条规格列表

型号

端口数

类型

断电检测机制

可检测的PD设备

Master DIMM

24

Master

AC

符合IEEE 802.3af标准的PD设备,也兼容非标准的PD设备

Slave DIMM

24

Slave

AC/DC

根据Master而定

 

1-1 Master DIMM

1-2 Slave DIMM

1.2  安装方式

请使用如下方式安装PoE DIMM条:

1.2.1  确认安装位置

1. 对于LSB系列单板(如LSB1GV48DB0LSB2GV48DB0

Master DIMM条插入接口板的J15插槽,Slave DIMM条插入接口板的J16插槽。

2. 对于其他单板(如LSQ1FV48SA0LSQ1GV48SA0LSQ1GV48SC0

Master DIMM条插入接口板具有Master丝印标识的插槽,Slave DIMM条插入接口板具有Slave丝印标识的插槽。

1.2.2  注意事项

(1)        在安装PoE DIMM条时,为了安全起见,请务必配带防静电手套或者防静电护腕。

(2)        在安装时请注意区分Slave DIMMMaster DIMM

l              对于LSB系列单板:Master DIMM条请插入接口板上具有PD67024MUAC丝印标识的插槽,Slave DIMM条插入接口板上具有PD67024S丝印标识的插槽。

l              对于其他单板: Master DIMM条请插入接口板上具有Master丝印标识的插槽,Slave DIMM条请插入接口板上具有Slave丝印标识的插槽。

l              只有Master DIMM条和Slave DIMM条均插入正确槽位,PoE模块才能正常工作。

1.2.3  安装步骤:

(1)        从盒中取出PoE DIMM条。

(2)        根据DIMM条的类型(Slave DIMMMaster DIMM)将其插入接口板上对应的DIMM槽位,并压紧启拔开关。

&  说明:

l      由于DIMM插槽已经设计为防反槽,因此用户无需担心会将PoE DIMM条安装方向插反。

l      PoE DIMM条只能在支持PoE的接口板上使用。

l      如果没插PoE DIMM条或者没有插紧PoE DIMM条,接口板无法进行远程供电,但其他业务可以正常工作。

l      Master DIMMSlave DIMM需同时使用。

 

 

杭州华三通信技术有限公司

 


PoE DIMM Module Installation Guide

1.1  Technical Specifications

Table 1 lists the technical specifications of the PoE DIMM modules.

Table 1        Technical specifications of PoE DIMM modules

Model

Number of ports

Type

Disconnect

Detection

Master DIMM

24

Master

AC

Powered devices (PDs) compliant with IEEE 802.3af or legacy standards

Slave DIMM

24

Slave

AC/DC

According to Master

 

Figure 1         Master DIMM

Figure 2         Slave DIMM

1.2  Installing the PoE DIMM Module

Follow these steps to install the PoE DIMM module:

1.2.1  Checking the Position of the Module

l           On an LSB series card, such as LSB1GV48DB0 and LSB2GV48DB0

Insert the Master DIMM module into the J15 socket of the interface card and the Slave DIMM module into the J16 socket.

l           On any other interface card, such as LSQ1FV48SA0, LSQ1GV48SA0, and LSQ1GV48SC0

Insert the Master DIMM module into the socket with the Master silkscreen on the interface card and the Slave DIMM module into the socket with the Slave silkscreen.

1.2.2  Precautions

l           For the sake of safety, make sure you wear an ESD-protective wrist strap or gloves when installing the PoE DIMM modules.

l           You must insert the Master and Slave DIMM modules in the right sockets.

l           On an LSB series card, insert the Master DIMM into the socket with the PD67024MUAC silkscreen on the interface card and the Slave DIMM into the socket with the PD67024S silkscreen.

l           On any other interface card, insert the Master DIMM module into the socket with the Master silkscreen on the interface card and the Slave DIMM module into the socket with the Slave silkscreen.

l           The PoE module can operate normally only if the Master DIMM and Slave DIMM are properly seated.

1.2.3  Installation Steps

l           Take out the PoE DIMM modules.

l           Insert the Master DIMM and Slave DIMM into the corresponding DIMM sockets and close the locking spring clips until the pins at both ends of the clip snap into the notches in the module.

 

&  Note:

l      The reverse insertion prevention design of the DIMM socket ensures that you can insert the module in the right direction.

l      PoE DIMM modules are supported on PoE interface cards only.

l      If no PoE DIMM module is in place or the module is not fully seated, the interface card cannot supply power, though other functions go well.

l      The Master and Slave DIMM modules must be used at the same time.

 

Hangzhou H3C Technologies Co., Ltd.

 

新华三官网
联系我们