Login
- Released At: 29-11-2024
- Page Views:
- Downloads:
- Related Documents
-
H3C EWPXM1XG03 Ethernet Interface Expansion Module Installation Guide-6W103
Introduction
The H3C EWPXM1XG03 Ethernet interface expansion module provides expansion ports for the WX3800X series access controllers.
Figure 1 EWPXM1XG03 Ethernet interface expansion module
Ports
The module provides eight 100/1000BASE-T Ethernet copper ports and two 10-GE SFP+ fiber ports.
Figure 2 Front panel
|
(2) 100/1000BASE-T Ethernet copper port LED |
|
|
(3) 100/1000BASE-T Ethernet copper port |
(4) SFP+ fiber port LED |
|
(5) SFP+ fiber port |
|
Ethernet copper ports
Table 1 100/1000BASE-T Ethernet copper port specifications
|
Item |
Specification |
|
Connector |
RJ-45 |
|
Port mode |
· 100/1000BASE-T autosensing · MDI/MDI-X autosensing |
|
Max transmission distance |
100 m (328.08 ft) |
|
Cable |
Category 5 or above twisted pair cables |
|
Standard |
IEEE 802.3ab |
SFP+ fiber ports
The transceiver modules that have MM and SM in their names support multi-mode optical fibers and single-mode optical fibers, respectively.
The SFP and SFP+ transceiver modules supported by the module are subject to change over time. For the most recent list of SFP and SFP+ transceiver modules available for the module, contact marketing staff or Technical Support.
Optional optical transceiver modules and cables, please refer to "H3C WX3800X Series Access Controllers Hardware Information and Specifications".
SFP+ fiber port specifications
Table 2 SFP+ fiber port specifications
|
Item |
Specification |
|
Connector |
LC |
|
Port transmission rate |
1 Gbps, 10 Gbps |
LEDs
Table 3 LED description
|
LED |
Status |
Description |
|
100/1000BASE-T Ethernet copper port LED |
Steady green |
The port is operating at 1000 Mbps, and a link is present on the port. |
|
Flashing green |
The port is sending or receiving data at 1000 Mbps. |
|
|
Steady yellow |
The port is operating at 100 Mbps, and a link is present on the port. |
|
|
Flashing yellow |
The port is sending or receiving data at 100 Mbps. |
|
|
Off |
No link is present on the port. |
|
|
SFP+ fiber port LED |
Steady green |
The port is operating at 10 Gbps, and a link is present on the port. |
|
Flashing green |
The port is sending or receiving data at 10 Gbps. |
|
|
Steady yellow |
The port is operating at 1 Gbps, and a link is present on the port. |
|
|
Flashing yellow |
The port is sending or receiving data at 1 Gbps. |
|
|
Off |
No transceiver module is installed or no link is present on the port. |
Installing and removing the module
|
|
CAUTION: · Do not use excessive force or touch the surface-mounted components directly with hands when you install or remove the module. · To avoid system anomalies, do not hot swap the module. |
Before installing or removing the module, prepare the ESD wrist strap and other tools that might be used.
Installing the module
|
|
IMPORTANT: · Keep the removed filler panel secure for future use. · Do not hot swap the module. Before you install or remove the module, make sure the device is powered off. |
To install an EWPXM1XG03:
1. Wear an ESD wrist strap and make sure the strap makes good skin contact and is reliably grounded.
2. Unpack the module.
3. Loosen the screws on the filler panel, and then remove the filler panel.
4. Insert the module into the target slot, and then fasten the captive screws.
Figure 3 Installing an EWPXM1XG03
Removing the module
If you are not to install a new module after removing the original one, install a filler panel in the slot.
To remove an EWPXM1XG03:
1. Wear an ESD wrist strap and make sure the strap makes good skin contact and is reliably grounded.
2. Loosen the captive screws on the module.
3. Pull the module slowly out of the slot.
Technical support
New H3C Technologies Co., Ltd. provides customers with comprehensive technical support and service. If you purchase the products from the sales agent of New H3C Technologies Co., Ltd., please contact our sales agent or technical personnel.
