Login
- Released At: 28-04-2024
- Page Views:
- Downloads:
- Table of Contents
- Related Documents
-
H3C SecPath NS-FWFFGA1 firewall module
1 Identifier
The module identifier NS-FWFFGA1 is in the upper right corner of the front panel.
2 About the module
The NS-FWFFGA1 firewall module has one console port, one USB port (for power output only, not in host mode), one copper management Ethernet port, and two 100GBASE-R fiber ports.
3 Specifications
Figure 1 Front panel
|
(1) Ejector lever |
(2) Console port |
|
(3) BMC network port (reserved) |
(4) USB port (for power output only, not in host mode) |
|
(5) 100GBASE-R fiber port LEDs |
(6) 100GBASE-R fiber port |
|
(7) BMC network port LED |
(8) Copper management Ethernet port |
|
(9) Copper management Ethernet port LED |
(10) Module status LED |
|
(11) CPU status LED |
(12) System power button |
Table 1 Module specifications
|
Item |
Specification |
|
Memory |
96GB RDIMMs |
|
Storage |
8 GB |
|
CPUs |
1 |
|
Dimensions (H × W × D) |
44 × 191 × 365 mm (1.73 × 7.52 × 14.37 in) |
|
Weight |
3.4 kg (7.49 lb) |
|
Power consumption |
208 W to 305 W |
|
Hot swapping |
Not supported |
|
Ports |
· 1 × console port · 1 × USB port (for power output only, not in host mode) · 1 × copper management Ethernet ports · 2 × 100G fiber ports |
|
Compatible modules and slots |
· M9000-AI-X06 multiservice security gateway (NSQM7MBSHC1 interface switch module slots 1 and 2) · M9000-AI-X10 multiservice security gateway (NSQM7MBSHC1 interface switch module slots 1 and 2) · M9000-X06 multiservice security gateway (NSQM7MBSHA0 interface switch module slots 1 and 2) |
Table 2 Console port specifications
|
Item |
Specification |
|
Connector |
RJ-45 |
|
Interface standard |
RS-232 |
|
Transmission baud rate |
· BMC console port: 38400 bps (default) · BIOS console port: 115200 bps (default) |
|
Transmission medium |
Asynchronous serial cable |
|
Transmission distance |
≤15 m (49.21 ft) |
|
Services |
· Provides connection to an ASCII terminal. · Provides connection to the serial port of a local PC running a terminal emulation program. · Supports the command line interface (CLI) |
Table 3 Copper management Ethernet port specifications
|
Item |
Specification |
|
Connector |
RJ-45 |
|
Interface standard |
802.3, 802.3u, and 802.3ab |
|
Interface type |
MDI/MDIX autosensing |
|
Transmission medium |
Category-5 or above twisted pair cable |
|
Transmission distance |
100 m (328.08 ft) |
|
Transmission rate and duplex mode |
· 10 Mbps, half/full duplex · 100 Mbps, half/full duplex · 1000 Mbps, full duplex |
Table 4 QSFP28 transceiver modules available for the 100GBASE-R fiber ports
|
Module |
Central wavelength |
Connector type |
Cable specifications |
Maximum transmission distance |
|
QSFP-100G-SR4-MM850 |
850 nm |
MPO |
50/125 µm, MMF |
100 m (328.08 ft) |
|
QSFP-100G-LR4-WDM1300 |
1310 nm |
LC |
9/125 µm, SMF |
10 km (6.21 miles) |
|
QSFP-100G-SWDM4-MM850 |
850 nm |
LC |
50/125 µm, MMF |
100 m (328.08 ft) |
4 LEDs
Table 5 LED description
|
LED |
Status |
Description |
|
Copper management Ethernet port LED |
Steady green |
A 1000 Mbps link is present on the port. |
|
Flashing green |
The port is sending or receiving data at 1000 Mbps. |
|
|
Steady yellow |
A 10/100 Mbps link is present on the port. |
|
|
Flashing yellow |
The port is sending or receiving data at 10/100 Mbps. |
|
|
Off |
No link is present on the port. |
|
|
100GBSAE-R fiber port LED |
Off |
No link is present on the port. |
|
Steady green |
A link is present on the port. |
|
|
Flashing green |
The port is sending or receiving data. |
|
|
Module status LED ( |
Steady green |
The module is operating correctly or a minor alarm has occurred. |
|
Flashing green at 4 Hz |
HDM is initializing. |
|
|
Flashing orange at 1 Hz |
A critical error has occurred on the module. |
|
|
Flashing red at 1 Hz |
An emergency error has occurred on the module. |
|
|
CPU status LED (RUN) |
Fast flashing green |
Software is being loaded. |
|
Slow flashing green |
The CPU is operating correctly. |
|
|
Steady red |
The CPU is faulty. |
|
|
Off |
The CPU is not operating. |
|
|
System power LED ( |
Steady green |
The system has started up. |
|
Flashing green at 1 Hz |
The system is starting up. |
|
|
Steady orange |
The system is in standby state. |
|
|
Off |
No power is present or the module is faulty. |
5 Related documentation
For information about installing the module, see the installation guide for the device.
Copyright © 2023 New H3C Technologies Co., Ltd.
The information in this document is subject to change without notice.
