Description

This software is used to upgrade the BIOS version of the R4300 G7 server

Installation steps

Publish Description

Supported products

H3C UniServer R4300 G7

Restrictions and cautions

Restrictions

None.

Guidelines

To avoid BIOS boot failures, do not upgrade or reset HDM during BIOS boot.

Version information

Version number

Version 7.00.18

Table 1 Target file name and MD5 checksum

You can access the HDM Web interface of the server to identify the BIOS firmware version in the Device information section of the Dashboard page, as shown in Figure 1.

Figure 1 Viewing the BIOS version number from HDM

BIOS built-in software version

Table 2 SP CPU BIOS built-in software version

Supported languages

English

Chinese

Supported devices

Hardware and software compatibility matrixes

Table 3 Hardware and software compatibility matrix for H3C UniServer R4300 G7

Table 4 Hardware and software compatibility matrix for H3C UniServer R4700 G7/R4900 G7

Update suggestions

This version is recommended.

Update restrictions and guidelines

Make sure the software versions are compatible with each other.

To update both HDM and the BIOS, update HDM first.

Make sure the server is running in stable state before the update. That is, the server is powered off or has entered the operating system.

If the server enters the OS before the update, you must power cycle the server for the new firmware to take effect.

If you select the Retain or Restore method to update the BIOS, the update occurs during POST after the server is powered on again. During the update, do not disconnect the power source from the server, or forcedly power off or restart the server.

If you select the Forcedly restore method to update the BIOS, do not disconnect the power source from the server, or power off or restart the server.

Selecting the Restore or Forcedly restore method will restore the default BIOS settings, including restoring the boot mode in the BIOS to the default (UEFI).

During BIOS update with Forcedly restore selected, writing BIOS data, such as restarting the system or saving BIOS configuration from the BIOS setup utility, can cause data write errors. This can lead to BIOS ROM integrity check failures and even system starting failures. If the system prompts Flash Image Broken! System Halt!, forcedly power off the server, and then try to update the BIOS with Forcedly restore selected again.

As a best practice of bulk update, make sure you can update one server successfully before you update the remaining servers.

Problems Solved

Resolved problems in BIOS-7.00.18

202507160122

Symptom: On the HDM quick system installation interface, the BIOS fails to access the MMIO space.

Condition: This symptom might occur if you perform HDM quick system installation.

202507010341

Symptom: In the OS, network adapter name ethx does not match the bus number.

Condition: This symptom might occur if you view bus number information of all network adapters in the OS.

202506051968

Symptom: When you set a boot password, an administrator password, and a user password that meet password complexity requirements via Redfish, the configuration does take effect after a BIOS restart.

Condition: This symptom might occur if you restart the BIOS after setting passwords via Redfish.

202507140704

Symptom: For VGA alarm information on HDM, some messages of the warning level need to be changed to the info level.

Condition: This symptom might occur if you view VGA alarm information from HDM.

202507241490

Symptom: The total memory capacity displayed on the BIOS POST interface does not include the capacity of the faulty memory.

Condition: This symptom might occur if you view the total memory capacity on the BIOS POST interface.

New Functions

Version:7.00.22P11(2026/1/26)

Upgrade recommendations

optional

Problems Solved

Resolved problems in BIOS-7.00.22P11

202601090877

Symptom: When a new OS boot option is added successfully, the new boot option fails to come first after a server restart.

Condition: This symptom might occur if you add a new OS boot option and restart the server.

202512021816

Symptom: After you save the HDM address in the BIOS setup utility, the page fails to refresh the HDM address information.

Condition: This symptom might occur if you save the HDM address on the BIOS setup utility.

New Functions

Version:7.00.21(2025/12/17)

Upgrade recommendations

Upgrade recommended

Problems Solved

Resolved problems in BIOS-7.00.21

202510240582

Symptom: In BIOS-7.00.11 and later versions, the options for the PCIE Network Configuration menu cannot be properly configured and retained.

Condition: This symptom might occur if you configure and retain the options for the PCIE Network Configuration menu in BIOS-7.00.11 and later versions.

202511100785

Symptom: The Route IP address field on the Server > BMC Dedicated Network Port menu of the BIOS setup utility needs to be changed to the Default Gateway field to provide more accurate information.

Condition: This symptom might occur if you view network port related fields on the Server > BMC Dedicated Network Port menu of the BIOS setup utility.

New Functions

Version:7.00.19(2025/10/21)

Upgrade recommendations

Upgrade recommended

Problems Solved

Resolved problems in BIOS-7.00.19

202509030846

Symptom: The system cannot access H3C iFIST when the system board of the server is embedded with the Renesas USB chip.

Condition: This symptom might occur if the system board of the server is embedded with the Renesas USB chip.

202508180319

Symptom: When you enter the BIOS setup utility after BIOS secure erasure succeeds, the administrator password and user password fail to be restored to the default.

Condition: This symptom might occur if you enter the BIOS setup utility to view the administrator and user passwords after BIOS secure erasure succeeds on HDM.

New Functions

Version:7.00.18(2025/8/29)

Upgrade recommendations

Upgrade recommended

Problems Solved

Resolved problems in BIOS-7.00.18

202507160122

Symptom: On the HDM quick system installation interface, the BIOS fails to access the MMIO space.

Condition: This symptom might occur if you perform HDM quick system installation.

202507010341

Symptom: In the OS, network adapter name ethx does not match the bus number.

Condition: This symptom might occur if you view bus number information of all network adapters in the OS.

202506051968

Symptom: When you set a boot password, an administrator password, and a user password that meet password complexity requirements via Redfish, the configuration does take effect after a BIOS restart.

Condition: This symptom might occur if you restart the BIOS after setting passwords via Redfish.

202507140704

Symptom: For VGA alarm information on HDM, some messages of the warning level need to be changed to the info level.

Condition: This symptom might occur if you view VGA alarm information from HDM.

202507241490

Symptom: The total memory capacity displayed on the BIOS POST interface does not include the capacity of the faulty memory.

Condition: This symptom might occur if you view the total memory capacity on the BIOS POST interface.

New Functions