description: Displays complete interface descriptions. If you do not specify this keyword, the command displays only the first 27 characters of each interface description.

down: Displays information about interfaces in down state and the causes for the down state. If you do not specify this keyword, the command displays information about interfaces in all states.

Usage guidelines

If you do not specify an aggregate interface type, the command displays information about all interfaces.

If you specify an aggregate interface type but do not specify an interface number, the command displays information about all aggregate interfaces of the specified type.

Examples

# Display detailed information about Layer 2 aggregate interface Bridge-Aggregation 1.

<Sysname> display interface bridge-aggregation 1

Bridge-Aggregation1

Current state: UP

Line protocol state: UP

IP packet frame type: Ethernet II, hardware address: 000f-e207-f2e0

Description: Bridge-Aggregation1 Interface

Bandwidth: 1000 kbps

2Gbps-speed mode, full-duplex mode

Link speed type is autonegotiation, link duplex type is autonegotiation

PVID: 1

Port link-type: Access

Tagged VLANs: None

UnTagged VLANs: 1

Last clearing of counters: Never

Last 300 seconds input: 6900 packets/sec 885160 bytes/sec 0%

Last 300 seconds output: 3150 packets/sec 404430 bytes/sec 0%

Input (total): 5364747 packets, 686688416 bytes

2682273 unicasts, 1341137 broadcasts, 1341337 multicasts, 0 pauses

Input (normal): 5364747 packets, 686688416 bytes

2682273 unicasts, 1341137 broadcasts, 1341337 multicasts, 0 pauses

Input: 0 input errors, 0 runts, 0 giants, 0 throttles

0 CRC, 0 frame, 0 overruns, - aborts

- ignored, - parity errors

Output (total): 1042508 packets, 133441832 bytes

1042306 unicasts, 0 broadcasts, 202 multicasts, - pauses

Output (normal): 1042508 packets, 133441832 bytes

1042306 unicasts, 0 broadcasts, 202 multicasts, 0 pauses

Output: 0 output errors, - underruns, - buffer failures

0 aborts, 0 deferred, 0 collisions, 0 late collisions

- lost carrier, - no carrier

# Display detailed information about Layer 3 aggregate interface Route-Aggregation 1.

<Sysname> display interface route-aggregation 1

Route-Aggregation1

Current state: UP

Line protocol state: UP

Description: Route-Aggregation1 Interface

Bandwidth: 1000 kbps

Maximum transmission unit: 1500

Internet protocol processing: Disabled

IP packet frame type: Ethernet II, hardware address: 0000-0000-0000

IPv6 packet frame type: Ethernet II, hardware address: 0000-0000-0000

Link speed type is autonegotiation, link duplex type is autonegotiation

Last clearing of counters: Never

Last 300 seconds input rate: 0 bytes/sec, 0 bits/sec, 0 packets/sec

Last 300 seconds output rate: 0 bytes/sec, 0 bits/sec, 0 packets/sec

Input (total): 0 packets, 0 bytes

0 unicasts, 0 broadcasts, 0 multicasts, 0 pauses

Input (normal): 0 packets, 0 bytes

0 unicasts, 0 broadcasts, 0 multicasts, 0 pauses

Input: 0 input errors, 0 runts, 0 giants, 0 throttles

0 CRC, 0 frame, 0 overruns, 0 aborts

0 ignored, 0 parity errors

Output (total): 0 packets, 0 bytes

0 unicasts, 0 broadcasts, 0 multicasts, 0 pauses

Output (normal): 0 packets, 0 bytes

0 unicasts, 0 broadcasts, 0 multicasts, 0 pauses

Output: 0 output errors, 0 underruns, 0 buffer failures

0 aborts, 0 deferred, 0 collisions, 0 late collisions

0 lost carrier, 0 no carrier

# Display brief information about Layer 2 aggregate interface Bridge-Aggregation 1.

<Sysname> display interface bridge-aggregation 1 brief

Brief information on interfaces in bridge mode:

Link: ADM - administratively down; Stby - standby

Speed: (a) – auto

Duplex: (a)/A - auto; H - half; F - full

Type: A - access; T - trunk; H - hybrid

Interface Link Speed Duplex Type PVID Description

BAGG1 DOWN auto A A 1

# Display brief information about Layer 3 aggregate interface Route-Aggregation 1.

<Sysname> display interface route-aggregation 1 brief

Brief information on interfaces in route mode:

Link: ADM - administratively down; Stby - standby

Protocol: (s) - spoofing

Interface Link Protocol Primary IP Description

RAGG1 UP UP --

Table 1 Command output

Field	Description
Bridge-Aggregation1	Layer 2 aggregate interface name.
Route-Aggregation1	Layer 3 aggregate interface name.
Current state	Physical link state of the interface: · Administratively DOWN—The interface has been shut down by using the shutdown command. · DOWN—The interface is administratively up, but its physical state is down (possibly because no physical link exists or the link has failed). · DOWN (No MEC license)—The interface has been shut down because the device does not have a MEC license. · UP—The interface is both administratively and physically up.
IP packet frame type	IPv4 packet framing format.
Description	Description of the interface.
Bandwidth	Expected bandwidth of the interface. This field is not displayed when the bandwidth is 0 kbps.
Unknown-speed mode, unknown-duplex mode	The interface speed and duplex mode are unknown.
Port link-type	Port link type: · Access. · Trunk. · Hybrid.
Tagged VLANs	VLAN whose packets are sent out of this interface with a tag.
Untagged VLANs	VLAN whose packets are sent out of this interface without a tag.
Last clearing of counters	Time when the reset counters interface command was last used to clear the interface statistics. This field displays Never if the reset counters interface command has never been used on the interface since device startup.
Last 300 seconds input/output rate	Average input or output rate over the last 300 seconds.
Input/Output (total)	Statistics of all packets received or sent on the interface.
Input/Output (normal)	Statistics of all normal packets received or sent on the interface.
Line protocol state	Data link layer state of the interface: · UP. · DOWN.
Maximum transmission unit	MTU of the interface.
Internet protocol processing	IP packet processing capability of the interface when the interface is not assigned an IP address: · Disabled—The interface cannot process IP packets. · Enabled—The interface can process IP packets.
Internet address: ip-address/mask-length (Type)	IP address of the interface and type of the address in parentheses. · Primary—Manually configured primary IP address. · Sub—Manually configured secondary IP address. If the interface has both primary and secondary IP addresses, the primary IP address is displayed. If the interface has only secondary IP addresses, the lowest secondary IP address is displayed. · DHCP-Allocated—DHCP allocated IP address. For more information, see DHCP client configuration in Layer 3—IP Services Configuration Guide. · BOOTP-Allocated—BOOTP allocated IP address. For more information, see BOOTP client configuration in Layer 3—IP Services Configuration Guide. · PPP-Negotiated—IP address assigned by a PPP server during PPP negotiation. For more information, see PPP configuration in Layer 2—WAN Access Configuration Guide. · Unnumbered—IP address borrowed from another interface. · MTunnel—IP address of the multicast tunnel interface (MTI), which is the same as the IP address of the MVPN source interface. For more information, see multicast VPN configuration in IP Multicast Configuration Guide.
Brief information on interfaces in route mode	Brief information about Layer 3 interfaces.
Brief information on interfaces in bridge mode	Brief information about Layer 2 interfaces.
Interface	Abbreviated interface name.
Link	Physical link state of the interface: · UP—The interface is physically up. · DOWN—The interface is physically down. · ADM—The interface has been shut down by using the shutdown command. To restore the physical state of the interface, use the undo shutdown command. · Stby—The interface is a backup interface in standby state.
Speed	Speed of the interface, in bps. This field displays the (a) flag next to the speed if the speed is automatically negotiated. This field displays auto if the interface is configured to autonegotiate its speed but the autonegotiation has not started.
Duplex	Duplex mode of the interface: · A—Autonegotiation. The interface is configured to autonegotiate its duplex mode but the autonegotiation has not started. · F—Full duplex. · F(a)—Autonegotiated full duplex. · H—Half duplex. · H(a)—Autonegotiated half duplex.
Type	Link type of the interface: · A—Access. · H—Hybrid. · T—Trunk.
Protocol	Data link layer protocol state of the interface: · UP—The data link layer protocol of the interface is up. · DOWN—The data link layer protocol of the interface is down. · UP(s)—The data link layer protocol of the interface is up, but the link is an on-demand link or does not exist. The (s) attribute represents the spoofing flag. This value is typical of null interfaces and loopback interfaces.
Primary IP	Primary IP address of the interface. This field displays two hyphens (--) if the interface does not have an IP address.
Cause	Cause for the physical link state of an interface to be DOWN.

display lacp system-id

Use display lacp system-id to display the local system ID.

Syntax

display lacp system-id

Views

Any view

Predefined user roles

network-admin

network-operator

Usage guidelines

You can use the lacp system-priority command to change the LACP priority of the local system. The LACP priority value is specified in decimal format in the lacp system-priority command. However, it is displayed in hexadecimal format in the output from the display lacp system-id command.

Examples

# Display the local system ID.

<Sysname> display lacp system-id

Actor System ID: 0x8000, 0000-fc00-6504

Table 2 Command output

Field	Description
Actor System ID: 0x8000, 0000-fc00-6504	Local system ID, which contains the LACP system priority (0x8000 in this sample output) and the LACP system MAC address (0000-FC00-6504 in this sample output).

Related commands

lacp system-priority

display link-aggregation load-sharing mode

Use display link-aggregation load-sharing mode to display global or group-specific link-aggregation load sharing modes.

Syntax

display link-aggregation load-sharing mode [ interface [ { bridge-aggregation | route-aggregation } interface-number ] ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

bridge-aggregation: Specifies Layer 2 aggregate interfaces.

route-aggregation: Specifies Layer 3 aggregate interfaces.

interface-number: Specifies an existing aggregate interface number.

Usage guidelines

If you do not specify the interface keyword, the command displays the global link-aggregation load sharing modes.

If you specify the interface keyword, but do not specify an interface, the command displays all group-specific load sharing modes.

The bridge-aggregation or route-aggregation keyword is available only when the corresponding aggregate interfaces exist on the device.

Examples

# Display the global link-aggregation load sharing mode. This example displays the default setting.

<Sysname> display link-aggregation load-sharing mode

Link-aggregation load-sharing mode (hardware forwarding):

Layer 2 traffic: destination-mac address source-mac address

Layer 3 traffic: destination-ip address source-ip address

ip-protocol

Layer 4 traffic: destination-port source-port

MPLS traffic : mpls-label1

Link-aggregation load-sharing mode (software forwarding):

Layer 3 traffic: destination-ip address source-ip address

Layer 4 traffic: destination-ip address source-ip address

# Display the link-aggregation load sharing mode of Layer 2 aggregation group 1. This example displays the default setting.

<Sysname> display link-aggregation load-sharing mode interface bridge-aggregation 1

Bridge-Aggregation8 load-sharing mode (hardware forwarding):

Layer 2 traffic: destination-mac address source-mac address

Layer 3 traffic: destination-ip address source-ip address

ip-protocol

Layer 4 traffic: destination-port source-port

MPLS traffic : mpls-label1

Bridge-Aggregation8 load-sharing mode (software forwarding):

Layer 3 traffic: destination-ip address source-ip address

Layer 4 traffic: destination-ip address source-ip address

Table 3 Command output

Field	Description
Link-aggregation load-sharing mode	Global link-aggregation load sharing mode. By default, this field displays the link-aggregation load sharing modes for Layer 2, Layer 3, Layer 4, and MPLS traffic. If you have configured the global link-aggregation load sharing mode, this field displays the configured mode.
Bridge-Aggregation1 load-sharing mode	Link-aggregation load sharing mode of Layer 2 aggregation group 1. By default, this field displays the global link-aggregation load sharing modes. If you have configured a link-aggregation load sharing mode for this aggregation group, this field displays the configured mode.
Route-Aggregation1 load-sharing mode	Link-aggregation load sharing mode of Layer 3 aggregation group 1. By default, this field displays the global link-aggregation load sharing modes. If you have configured a link-aggregation load sharing mode for this aggregation group, this field displays the configured mode.
Layer 2 traffic: packet type-based sharing	Default link-aggregation load sharing mode for Layer 2 traffic. In this sample output, Layer 2 traffic is load shared based on the packet type.
Layer 3 traffic: destination-ip address, source-ip address	Default link-aggregation load sharing mode for Layer 3 traffic. In this sample output, Layer 3 traffic is load shared based on source and destination IP addresses.
Layer 3 traffic: packet type-based sharing	Default link-aggregation load sharing mode for Layer 3 traffic. In this sample output, Layer 3 traffic is load shared based on the packet type.
Layer 4 traffic: destination-port, source-port	Default link-aggregation load sharing mode for Layer 4 traffic. In this sample output, Layer 4 traffic is load shared based on source and destination ports.
MPLS traffic : mpls-label1, mpls-label2, mpls-label3	Default link-aggregation load sharing mode for MPLS traffic. In this sample output, MPLS traffic is load shared based on Layer 1 through Layer 3 MPLS labels.
destination-mac address, source-mac address	User-configured link-aggregation load sharing mode. In this sample output, traffic is load shared based on source and destination MAC addresses.

display link-aggregation member-port

Use display link-aggregation member-port to display detailed link aggregation information about the specified member ports.

Syntax

display link-aggregation member-port [ interface-list | auto ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

interface-list: Specifies a list of link aggregation member ports, in the format interface-type interface-number1 [ to interface-type interface-number2 ]. The value for the interface-number2 argument must be equal to or greater than the value for the interface-number1 argument.

auto: Specifies all link aggregation member ports that are enabled with automatic assignment.

Usage guidelines

A member port in a static aggregation group cannot obtain information about the peer group. For such member ports, the command displays the port number, port priority, and operational key of only the local end.

Examples

# Display detailed information about GigabitEthernet 0/0/1, which is a member port of a static aggregation group.

<Sysname> display link-aggregation member-port gigabitethernet 0/0/1

Flags: A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation,

D -- Synchronization, E -- Collecting, F -- Distributing,

G -- Defaulted, H -- Expired

GigabitEthernet0/0/1:

Aggregate Interface: Bridge-Aggregation1

Port Number: 1

Port Priority: 32768

Oper-Key: 1

# Display detailed information about GigabitEthernet 0/0/2, which is a member port of a dynamic aggregation group.

<Sysname> display link-aggregation member-port gigabitethernet 0/0/2

Flags: A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation,

D -- Synchronization, E -- Collecting, F -- Distributing,

G -- Defaulted, H -- Expired

GigabitEthernet0/0/2:

Aggregate Interface: Bridge-Aggregation10

Local:

Port Number: 2

Port Priority: 32768

Oper-Key: 2

Flag: {ACDEF}

Remote:

System ID: 0x8000, 000f-e267-6c6a

Port Number: 26

Port Priority: 32768

Oper-Key: 2

Flag: {ACDEF}

Received LACP Packets: 5 packet(s)

Illegal: 0 packet(s)

Sent LACP Packets: 7 packet(s)

Table 4 Command output

Field	Description
Flags	LACP state flags. This field is one byte long, represented by ABCDEFGH from the least significant bit to the most significant bit. A letter appears when its bit is 1 and does not appear when its bit is 0. · A—Indicates whether LACP is active on the port. 1 indicates active. 0 indicates passive. · B—Indicates the LACP timeout interval. 1 indicates the short timeout interval. 0 indicates the long timeout interval. · C—Indicates whether the sending system considers that the link is aggregatable. 1 indicates yes. 0 indicates no. · D—Indicates whether the sending system considers that the link has been aggregated. 1 indicates yes. 0 indicates no. · E—Indicates whether the sending system considers that the link can collect frames. 1 indicates yes. 0 indicates no. · F—Indicates whether the sending system considers that the link can distribute frames. 1 indicates yes. 0 indicates no. · G—Indicates whether the RX state machine of the sending system is in default state. 1 indicates yes. 0 indicates no. · H—Indicates whether the RX state machine of the sending system is in expired state. 1 indicates yes. 0 indicates no.
Aggregate Interface	Aggregate interface to which the member port belongs.
Preferred Aggregate Interface	Aggregate interface to which you prefer to assign the member port during automatic assignment.
Local	Information about the local end.
Oper-key	Operational key.
Flag	LACP protocol state flag.
Remote	Information about the peer end.
System ID	Peer system ID, containing the LACP system priority and the LACP system MAC address.
Received LACP Packets	Total number of LACP packets received.
Illegal	Total number of illegal packets.
Sent LACP Packets	Total number of LACP packets sent.

display link-aggregation summary

Use display link-aggregation summary to display brief information about all aggregation groups.

Syntax

display link-aggregation summary

Views

Any view

Predefined user roles

network-admin

network-operator

Usage guidelines

The Partner ID field in the command output always displays None or nothing for a static link aggregation group. This is because the local aggregation system cannot obtain information from the peer system in a static link aggregation.

Examples

# Display brief information about all aggregation groups.

<Sysname> display link-aggregation summary

Aggregate Interface Type:

BAGG -- Bridge-Aggregation, BLAGG –- Blade-Aggregation, RAGG -- Route-Aggregation, SCH-B – Schannel-Bundle

Aggregation Mode: S -- Static, D -- Dynamic

Loadsharing Type: Shar -- Loadsharing, NonS -- Non-Loadsharing

Actor System ID: 0x8000, 000f-e267-6c6a

AGG AGG Partner ID Selected Unselected Individual Share

Interface Mode Ports Ports Ports Type

--------------------------------------------------------------------------------

RAGG10 S None 1 0 0 NonS

BAGG20 D 0x8000,00e0-fcff-ff01 2 0 0 Shar

Table 5 Command output

Field	Description
Aggregate Interface Type	Aggregate interface type: · BAGG—Layer 2. · RAGG—Layer 3.
Aggregation Mode	Aggregation group type: · S—Static. · D—Dynamic.
Loadsharing Type	Load sharing type: · Shar—Load-sharing. · NonS—Non-load-sharing.
Actor System ID	Local system ID, which contains the local LACP system priority and the local LACP system MAC address.
AGG Interface	Type and number of the aggregate interface.
AGG Mode	Aggregation group type.
Partner ID	System ID of the peer system, which contains the peer LACP system priority and the peer LACP system MAC address.
Selected Ports	Total number of Selected ports.
Unselected Ports	Total number of Unselected ports.
Individual Ports	Total number of Individual ports.
Share Type	Load sharing type.

display link-aggregation troubleshooting

Use display link-aggregation troubleshooting to display the aggregation states of aggregation member ports and the reason why a port was placed in Unselected state.

Syntax

display link-aggregation troubleshooting [ { bridge-aggregation | route-aggregation } [ interface-number ] ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

bridge-aggregation: Specifies Layer 2 aggregate interfaces.

route-aggregation: Specifies Layer 3 aggregate interfaces.

interface-number: Specifies an existing aggregate interface by its number.

Usage guidelines

If you do not specify an aggregate interface type, the command displays information about all aggregation groups.

If you specify an aggregate interface type but do not specify an interface number, the command displays information about all aggregation groups of the specified type.

You can specify the bridge-aggregation or route-aggregation keyword only when aggregate interfaces of the specified type exist on the device.

Examples

# Display the aggregation states of aggregation member ports for all aggregation groups and the reason why a port was placed in Unselected state.

<Sysname> display link-aggregation troubleshooting

Aggregate Interface: Bridge-Aggregation2

Member ports:

GE0/0/2

Status: Selected

GE0/0/3

Status: Unselected

Reason: The physical or line protocol state of the port is down

Advice: Check the connection

Table 6 Command output

Field	Description
Reason	Reason why the port was placed in Unselected state.
Advice	Recommended action.

Table 7 Reason why the port was placed in Unselected state

Field
The number of Selected ports had reached the upper limit
Hardware resources were not enough
The number of Selected ports was below the lower limit
The link aggregation configuration of the port was incorrect
The link aggregation configuration of its peer port was incorrect
The physical or line protocol state of the port was down
The port's hardware restriction prevented it from being Selected
The speed configuration of the port was different from that of the reference port
The duplex mode of the port was different from that of the reference port
The port and the aggregate interface had different attribute configurations
The port was in secondary state in a redundancy group
The BFD session state of the port was down
The member port has low link quality
It is the secondary member port in the aggregation group in 1+1 backup mode
No LACPDU was received by the reference port
The reference port received its own LACPDUs
The link of the port was not aggregatable
The link of the peer port was not aggregatable
The card that hosts the port was absent
The port's operational key was invalid
Link-aggregation traffic redirection was triggered on the local port
The port had not received LACPDUs
The operational key of the peer port was different from that of the reference port
The system MAC address of the peer port was different from that of the peer port for the reference port
The peer port did not have the Synchronization flag
The port was in Standby state
Link-aggregation lacp isolate is configured

Table 8 Recommended action

Field
Modify the aggregation group configuration
Release resources
Modify port configuration
Modify peer port configuration
Check the connection
Use another port
Change the port rate to be the same as that of the reference port
Change the port duplex mode to be the same as that of the reference port
Change the port attribute configuration to be the same as that of the aggregate interface
Place the port in primary state in the redundancy group
Check the link that conveys the BFD session
Check for CRC errors
Check whether the peer sends LACPDUs correctly
Check whether the device has a loop
Make sure the card that hosts the port is installed
Check whether the port sends LACPDUs correctly
Change the peer system MAC address to be the same as that of the reference port
Check the LACPDUs sent by the peer
Please check the aggregation state of member ports in a few minutes
Make sure the peer aggregation member ports for a M-LAG group reside on the same device and belong to the same aggregation group
Check the configuration
N/A

display link-aggregation verbose

Use display link-aggregation verbose to display detailed information about the aggregation groups that correspond to the specified aggregate interfaces.

Syntax

display link-aggregation verbose [ { bridge-aggregation | route-aggregation } [ interface-number ] ] [ all-configuration ]

Views

Any view

Predefined user roles

network-admin

network-operator

Parameters

bridge-aggregation: Specifies Layer 2 aggregate interfaces.

route-aggregation: Specifies Layer 3 aggregate interfaces.

interface-number: Specifies an existing aggregate interface by its number.

all-configuration: Specifies all member ports in an aggregation group. If you do not specify this keyword, the command displays the member ports on present cards.

Usage guidelines

If you do not specify an aggregate interface type, the command displays detailed information about all aggregation groups.

If you specify an aggregate interface type but do not specify an interface number, the command displays detailed information about all aggregation groups of the specified type.

The bridge-aggregation or route-aggregation keyword is available only when the corresponding aggregate interfaces exist on the device.

This command does not display the interfaces that are enabled with automatic assignment if they have not joined an aggregation group.

Examples

# Display detailed information about Layer 2 aggregation group 10, which is a dynamic aggregation group.

<Sysname> display link-aggregation verbose bridge-aggregation 10

Loadsharing Type: Shar -- Loadsharing, NonS -- Non-Loadsharing

Port Status: S -- Selected, U -- Unselected, I -- Individual

Port: A -- Auto port, M -- Management port, R -- Reference port

Flags: A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation,

D -- Synchronization, E -- Collecting, F -- Distributing,

G -- Defaulted, H -- Expired

Role: P -- Primary, S -- Secondary

Aggregate Interface: Bridge-Aggregation10

Creation Mode: Manual

Aggregation Mode: Dynamic

Loadsharing Type: Shar

Management VLANs: None

System ID: 0x8000, 000f-e267-6c6a

Local:

Port Status Priority Index Oper-Key Flag

GE0/0/1 S 32768 61 2 {ACDEF}

GE0/0/2 S 32768 62 2 {ACDEF}

GE0/0/3 S 32768 63 2 {ACDEF}

Remote:

Actor Priority Index Oper-Key SystemID Flag

GE0/0/1(R) S 32768 1 1 {ACDEF}

GE0/0/2 32768 112 2 0x8000, 000f-e267-57ad {ACDEF}

GE0/0/3 32768 113 2 0x8000, 000f-e267-57ad {ACDEF}

# Display detailed information about Layer 2 aggregation group 20, which is a static aggregation group.

<Sysname> display link-aggregation verbose bridge-aggregation 20

Loadsharing Type: Shar -- Loadsharing, NonS -- Non-Loadsharing

Port Status: S -- Selected, U -- Unselected, I -- Individual

Port: A -- Auto port, M -- Management port, R -- Reference port

Flags: A -- LACP_Activity, B -- LACP_Timeout, C -- Aggregation,

D -- Synchronization, E -- Collecting, F -- Distributing,

G -- Defaulted, H -- Expired

Role: P -- Primary, S -- Secondary

Aggregate Interface: Bridge-Aggregation20

Aggregation Mode: Static

Loadsharing Type: Shar

Management VLANs: None

Port Status Priority Oper-Key Role

GE0/0/1(R) S 32768 1

GE0/0/2 S 32768 1 None

GE0/0/3 S 32768 1 None

Table 9 Command output

Field	Description
Loadsharing Type	Load sharing type: · Shar—Load-sharing. · NonS—Non-load-sharing.
Port Status	Port state: · Selected. · Unselected. · Individual.
Port	Port type: · Auto port—The port is enabled with automatic assignment. · Management port—The port is a management port. · Reference port—The port is a reference port.
Flags	LACP state flags. This field is one byte long, represented by ABCDEFGH from the least significant bit to the most significant bit. A letter appears when its bit is 1 and does not appear when its bit is 0. · A—Indicates whether LACP is active on the port. 1 indicates active. 0 indicates passive. · B—Indicates the LACP timeout interval. 1 indicates the short timeout interval. 0 indicates the long timeout interval. · C—Indicates whether the sending system considers that the link is aggregatable. 1 indicates yes. 0 indicates no. · D—Indicates whether the sending system considers that the link has been aggregated. 1 indicates yes. 0 indicates no. · E—Indicates whether the sending system considers that the link can collect frames. 1 indicates yes. 0 indicates no. · F—Indicates whether the sending system considers that the link can distribute frames. 1 indicates yes. 0 indicates no. · G—Indicates whether the RX state machine of the sending system is in default state. 1 indicates yes. 0 indicates no. · H—Indicates whether the RX state machine of the sending system is in expired state. 1 indicates yes. 0 indicates no.
Role	Role of the port in the aggregation group operating in 1+1 backup mode: · Primary. · Secondary. If the aggregation group is not operating in 1+1 backup mode, None is displayed.
Aggregate Interface	Name of the aggregate interface.
Creation Mode	Creation mode of the dynamic aggregate interface: · Auto. · Manual.
Aggregation Mode	Aggregation group type: · S—Static. · D—Dynamic.
Management VLANs	Management VLANs. If no management VLANs are specified, this field displays None.
System ID	Local system ID, containing the local LACP system priority and the local LACP system MAC address.
Local	Information about the local end: · Port—Port type and number. · Status—Port state, which can be Selected, Unselected, or Individual. · Priority—Port priority. · Index—Port index. · Oper-Key—Operational key. · Flag—LACP state flag. NOTE: For static aggregation groups, the Index and Flag fields are not displayed.
Remote	Information about the peer end: · Actor—Type and number of the local port. This field displays the (R) flag next to the port if its peer port is the reference port. · Priority—Priority of the peer port. · Index—Index of the peer port. · Oper-Key—Operational key of the peer port. · System ID—System ID of the peer end. · Flag—LACP state flag of the peer end.

interface bridge-aggregation

Use interface bridge-aggregation to create a Layer 2 aggregate interface and enter its view, or enter the view of an existing Layer 2 aggregate interface.

Use undo interface bridge-aggregation to delete a Layer 2 aggregate interface.

Syntax

interface bridge-aggregation interface-number

undo interface bridge-aggregation interface-number

The following compatibility matrixes show the support of hardware platforms for this command:

Hardware	Command compatibility
MSR1008	Yes
MSR1004-G	No
MSR1004-G-5GCN	No
MSR2630E-X1	Yes
MSR3610E-X1, MSR3610E-X1-DP	Yes
MSR3610-G-X3-DP, MSR3610-G-X3, MSR3610-G-X3-DP-DC, MSR3610-G-X3-DC	No

‌

Hardware	Command compatibility
MSR2660-XS	Yes
MSR2680-XS	Yes

‌

Hardware	Command compatibility
MSR2600-12X-WiNet	Yes
MSR2610-13X-WiNet	Yes

‌

Default

No Layer 2 aggregate interfaces exist.

Views

System view

Predefined user roles

network-admin

Parameters

interface-number: Specifies a Layer 2 aggregate interface number. The value range for the interface-number argument is 1 to 8.

Usage guidelines

When you create a Layer 2 aggregate interface, the system automatically creates a Layer 2 aggregation group with the same number. The aggregation group operates in static aggregation mode by default.

Deleting a Layer 2 aggregate interface also deletes the Layer 2 aggregation group. At the same time, the member ports of the aggregation group, if any, leave the aggregation group.

Examples

# Create Layer 2 aggregate interface Bridge-Aggregation 1, and enter its view.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1]

interface route-aggregation

Use interface route-aggregation to create a Layer 3 aggregate interface or subinterface and enter its view, or enter the view of an existing Layer 3 aggregate interface or subinterface.

Use undo interface route-aggregation to delete a Layer 3 aggregate interface or subinterface.

Syntax

interface route-aggregation { interface-number | interface-number.subnumber }

undo interface route-aggregation { interface-number | interface-number.subnumber }

Default

No Layer 3 aggregate interfaces or subinterfaces exist.

Views

System view

Predefined user roles

network-admin

Parameters

interface-number: Specifies a Layer 3 aggregate interface number. The value range for the interface-number argument is 1 to 8.

interface-number.subnumber: Specifies a subinterface of a Layer 3 aggregate interface. The interface-number argument specifies the main interface number. The subnumber argument specifies the subinterface number and is separated from the main interface number by a dot (.). The value range for the subnumber argument is 1 to 4094.

Usage guidelines

When you create a Layer 3 aggregate interface, the system automatically creates a Layer 3 aggregation group with the same number. The Layer 3 aggregation group operates in static aggregation mode by default.

Deleting a Layer 3 aggregate interface also deletes the Layer 3 aggregation group and all its aggregate subinterfaces. At the same time, the member ports of the aggregation group, if any, leave the aggregation group.

Deleting a Layer 3 aggregate subinterface does not affect the state of the main interface and the corresponding aggregation group.

Examples

# Create Layer 3 aggregate interface Route-Aggregation 1 and enter its view.

<Sysname> system-view

[Sysname] interface route-aggregation 1

[Sysname-Route-Aggregation1]

jumboframe enable

Use jumboframe enable to allow the jumbo frames on an interface to pass through.

Use undo jumboframe enable to deny jumbo frames on an interface.

Use undo jumboframe enable size to restore the default.

Syntax

jumboframe enable [ size ]

undo jumboframe enable [ size ]

Default

An aggregate interface allows jumbo frames that are within 9664 bytes to pass through.

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Predefined user roles

network-admin

Parameters

size: Specifies the maximum length of jumbo frames, in bytes. The value of this argument is fixed at 9664.

Usage guidelines

If you execute this command multiple times, the most recent configuration takes effect.

Examples

# Allow jumbo frames on Layer 2 aggregate interface Bridge-Aggregation 1.

<Sysname> System-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] jumboframe enable

lacp default-selected-port disable

Use lacp default-selected-port disable to disable the default port selection action for dynamic aggregation groups.

Use undo lacp default-selected-port disable to enable the default port selection action for dynamic aggregation groups.

Syntax

lacp default-selected-port disable

undo lacp default-selected-port disable

Default

The default port selection action is enabled for dynamic aggregation groups.

Views

System view

Predefined user roles

network-admin

Usage guidelines

The default port selection action applies to dynamic aggregation groups.

This action automatically chooses the port with the lowest ID from among all up member ports as a Selected port if none of them has received LACPDUs before the LACP timeout interval expires.

After this action is disabled, a dynamic aggregation group will not have any Selected ports to forward traffic if it has not received LACPDUs before the LACP timeout interval expires.

Examples

# Disable the default port selection action.

<Sysname> system-view

[Sysname] lacp default-selected-port disable

lacp edge-port

Use lacp edge-port to configure an aggregate interface as an edge aggregate interface.

Use undo lacp edge-port to restore the default.

Syntax

lacp edge-port

undo lacp edge-port

Default

An aggregate interface does not operate as an edge aggregate interface.

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Predefined user roles

network-admin

Usage guidelines

Use this command on the aggregate interface that connects the device to a server if dynamic link aggregation is configured only on the device. This feature improves link reliability by enabling all member ports of the aggregation group to forward packets.

This command takes effect only on an aggregate interface corresponding to a dynamic aggregation group.

Link-aggregation traffic redirection cannot operate correctly on an edge aggregate interface.

Examples

# Configure Layer 2 aggregate interface Bridge-Aggregation 1 as an edge aggregate interface.

<Sysname> System-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] lacp edge-port

lacp mode

Use lacp mode passive to configure LACP to operate in passive mode on a port.

Use undo lacp mode to restore the default.

Syntax

lacp mode passive

undo lacp mode

Default

LACP operates in active mode on a port.

Views

Layer 2 Ethernet interface view

Layer 3 Ethernet interface view

Predefined user roles

network-admin

Usage guidelines

This command takes effect only on member ports of dynamic aggregation groups.

When LACP is operating in passive mode on a local member port and its peer port, both ports cannot send LACPDUs. When LACP is operating in active mode on either end of a link, both ports can send LACPDUs.

Examples

# Configure LACP to operate in passive mode on GigabitEthernet 0/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 0/0/1

[Sysname-GigabitEthernet0/0/1] lacp mode passive

lacp period short

Use lacp period short to enable the short LACP timeout interval (3 seconds) on an interface.

Use undo lacp period to restore the default.

Syntax

lacp period short

undo lacp period

Default

The LACP timeout interval is the long timeout interval (90 seconds) on an interface.

Views

Layer 2 Ethernet interface view

Layer 3 Ethernet interface view

Predefined user roles

network-admin

Examples

# Enable the short LACP timeout interval (3 seconds) on GigabitEthernet 0/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 0/0/1

[Sysname-GigabitEthernet0/0/1] lacp period short

lacp preempt delay

Use lacp select speed to set the preemption delay for an aggregate interface.

Use undo lacp select speed to restore the default.

Syntax

lacp preempt delay delay-time

undo lacp preempt delay

Default

The preemption delay for an aggregate interface is 0 seconds, which means preemption occurs immediately.

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Predefined user roles

network-admin

Parameters

delay-time: Specifies the preemption delay time for the aggregate interface. The value range is 10 to 180 seconds.

Usage guidelines

For a dynamic aggregate interface, when Selected port A fails, the device selects member port B with the highest priority from the member ports that meet the conditions of becoming a Selected port. If preemption is enabled, port A will replace port B on recovery. To avoid packet loss caused by an unstable port A taking over port B, set a preemption delay time for the aggregate interface.

Examples

# Set the preemption delay for an aggregate interface to 100 seconds.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] lacp preempt delay 100

lacp preempt enable

Use lacp preempt enable to enable the preemption feature on an aggregate interface.

Use undo lacp preempt enable to disable the preemption feature on an aggregate interface.

Syntax

lacp preempt enable

undo lacp preempt enable

Default

The preemption feature on an aggregate interface is enabled.

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Predefined user roles

network-admin

Usage guidelines

For a dynamic aggregate interface, when Selected port A fails, the device selects member port B with the highest priority from the member ports that meet the conditions of becoming a Selected port. If the preemption feature is enabled on the aggregate interface, port A will replace port B on recovery. If the preemption feature is disabled on the aggregate interface, port B will continue to be the Selected port to reduce packet loss caused by selected port switching, even if its priority is lower than port A's.

Examples

# Disable the preemption feature on an aggregate interface.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] undo lacp preempt enable

lacp select speed

Use lacp select speed to configure a dynamic aggregation group to use port speed as the prioritized criterion for reference port selection.

Use undo lacp select speed to restore the default.

Syntax

lacp select speed

undo lacp select speed

Default

Port ID is the prioritized criterion for reference port selection in a dynamic aggregation group.

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Predefined user roles

network-admin

Usage guidelines

CAUTION:

Changing reference port selection criteria might cause transient traffic interruption. When you use this command, make sure you understand its impact on your network.

This command enables a dynamic aggregation group to select a high-speed member port as the reference port.

You must execute this command at both ends of the aggregate link so the peer aggregation systems use the same criteria for reference port selection.

As a best practice, shut down the peer aggregate interfaces before you execute this command and bring up the interfaces after this command is executed on both of them.

This command takes effect only on dynamic aggregate interfaces. On a static aggregate interface, you can execute this command, but the setting cannot take effect.

Examples

# Specify port speed as the prioritized criterion for reference port selection on Layer 2 dynamic aggregate interface Bridge-Aggregation 1.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] link-aggregation mode dynamic

[Sysname-Bridge-Aggregation1] lacp select speed

lacp system-mac

Use lacp system-mac to set the LACP system MAC address.

Use undo lacp system to restore the default.

Syntax

lacp system-mac mac-address

undo lacp system-mac

Default

The LACP system MAC address is the bridge MAC address of the device.

Views

System view

Predefined user roles

network-admin

Parameters

mac-address: Specifies a MAC address in the format of H-H-H. The MAC address cannot be an all-zero or all-F MAC address.

Usage guidelines

All S-MLAG devices must use the same LACP system MAC address.

LACPDUs carry the LACP system MAC address configured by using this command. To identify the LACP system MAC address used by a link aggregation group, examine the System ID field in the output from the display link-aggregation verbose command.

You can configure the LACP system MAC address globally and in aggregate interface view. The global LACP system MAC address takes effect on all aggregation groups, and an aggregate-interface-specific LACP system MAC address takes precedence over the global LACP system MAC address.

Examples

# Set the LACP system MAC address to 0001-0001-0001.

<Sysname> system-view

[Sysname] lacp system-mac 1-1-1

Related commands

display link-aggregation verbose

lacp system-number

Use lacp system-number to set the LACP system number used by the local device.

Use undo lacp system-number to restore the default.

Syntax

lacp system-number number

undo lacp system-number

Default

The LACP system number is not set.

Views

System view

Predefined user roles

network-admin

Parameters

number: Specifies a number in the range of 1 to 3.

Usage guidelines

You must assign a unique LACP system number to each S-MLAG device.

The LACP system number configured by using this command takes effect only on aggregate interfaces in S-MLAG groups. Aggregate interfaces not in S-MLAG groups do not use the configured LACP system number in LACPDUs. To view the LACP system number in LACPDUs, examine the Index field in the output from the display link-aggregation verbose command.

Examples

# Set the LACP system number to 1.

<Sysname> system-view

[Sysname] lacp system-number 1

Related commands

display link-aggregation verbose

lacp system-priority

Use lacp system-priority to set the LACP system priority.

Use undo lacp system-priority to restore the default.

Syntax

lacp system-priority priority

undo lacp system-priority

Default

The LACP system priority is 32768.

Views

System view

Predefined user roles

network-admin

Parameters

priority: Specifies the LACP system priority in the range of 0 to 65535. The smaller the value, the higher the LACP system priority.

Usage guidelines

LACPDUs carry the LACP system priority configured by using this command. To identify the LACP system priority used by a link aggregation group, examine the System ID field in the output from the display link-aggregation verbose command.

You can configure the LACP system priority globally and in aggregate interface view. The global LACP system priority takes effect on all aggregation groups, and an aggregate-interface-specific LACP system priority takes precedence over the global LACP system priority.

Examples

# Set the LACP system priority to 64.

<Sysname> system-view

[Sysname] lacp system-priority 64

Related commands

link-aggregation port-priority

link-aggregation bfd

Use link-aggregation bfd to enable BFD for an aggregation group.

Use undo link-aggregation bfd to disable BFD for an aggregation group.

Syntax

link-aggregation bfd ipv4 source ipv4-address destination ipv4-address

undo link-aggregation bfd ipv4

Default

BFD is disabled for an aggregation group.

Views

Layer 3 aggregate interface view

Predefined user roles

network-admin

Parameters

ipv4: Specifies IPv4 BFD.

source: Specifies the unicast source IP address of BFD sessions.

destination: Specifies the unicast destination IP address of BFD sessions.

ipv4-address: Specifies an IPv4 address. The address cannot be 0.0.0.0.

Usage guidelines

Make sure the source and destination IP addresses are reversed between the two ends of an aggregate link. For example, if you execute link-aggregation bfd ipv4 source 1.1.1.1 destination 2.2.2.2 at the local end, execute link-aggregation bfd ipv4 source 2.2.2.2 destination 1.1.1.1 at the peer end. The source and destination IP addresses cannot be the same.

The BFD parameters configured on an aggregate interface take effect on all BFD sessions established by the member ports in its aggregation group. BFD on a link aggregation supports only control packet mode for session establishment and maintenance. The two ends of an established BFD session can only operate in Asynchronous mode. For more information about BFD, see High Availability Configuration Guide.

As a best practice, do not configure BFD for any protocols on a BFD-enabled aggregate interface.

Make sure the number of member ports in the BFD-enabled aggregation group is less than or identical to the number of BFD sessions supported by the device. If the aggregation group contains more member ports than the supported sessions, some Selected ports might change to the Unselected state.

If the number of BFD sessions differs between the two ends of an aggregate link, check their settings for inconsistency in the maximum number of Selected ports. You must make sure the two ends have the same setting for the maximum number of Selected ports.

Examples

# Enable BFD for Layer 3 aggregation group 1, and specify the source and destination IP addresses as 1.1.1.1 and 2.2.2.2 for BFD sessions

<Sysname> system-view

[Sysname] interface route-aggregation 1

[Sysname-Route-Aggregation1] link-aggregation bfd ipv4 source 1.1.1.1 destination 2.2.2.2

link-aggregation bfd-compatible enable

Use link-aggregation bfd-compatible enable to enable BFD compatible mode on an aggregate interface.

Use undo link-aggregation bfd-compatible enable to disable BFD compatible mode on an aggregate interface.

Syntax

link-aggregation bfd-compatible enable

undo link-aggregation bfd-compatible enable

Default

BFD compatible mode is disabled on aggregate interfaces.

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Predefined user roles

network-admin

Usage guidelines

BFD compatible mode enables BFD to operate correctly on an aggregate link whose remote end is a third-party device that implements BFD differently from the device.

With BFD compatible mode enabled, all member ports in an aggregation group establish BFD sessions with their peer ports. The BFD sessions are not deleted or re-established when the aggregation states of the member ports change.

Examples

# Enable BFD compatible mode on Bridge-Aggregation 1.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] link-aggregation bfd-compatible enable

# Enable BFD compatible mode on Route-Aggregation 1.

<Sysname> system-view

[Sysname] interface route-aggregation 1

[Sysname-Route-Aggregation1] link-aggregation bfd-compatible enable

Related commands

link-aggregation bfd

link-aggregation global load-sharing mode

Use link-aggregation global load-sharing mode to set the global link-aggregation load sharing mode.

Use undo link-aggregation global load-sharing mode to restore the default.

Syntax

link-aggregation global load-sharing mode { destination-ip | destination-mac | destination-port | ingress-port | ip-protocol | mpls-label1 | source-ip | source-mac | source-port | vlan-id } *

undo link-aggregation global load-sharing mode

Default

The device distributes traffic based on the source and destination IP addresses on aggregate links.

Views

System view

Predefined user roles

network-admin

Parameters

destination-ip: Distributes traffic based on destination IP addresses.

destination-mac: Distributes traffic based on destination MAC addresses.

The following compatibility matrixes show the support of hardware platforms for this keyword:

Hardware	Parameter compatibility
MSR1008	Yes
MSR1004-G	No
MSR1004-G-5GCN	No
MSR2630E-X1	Yes
MSR3610E-X1, MSR3610E-X1-DP	Yes
MSR3610-G-X3-DP, MSR3610-G-X3, MSR3610-G-X3-DP-DC, MSR3610-G-X3-DC	Yes

‌

Hardware	Parameter compatibility
MSR2660-XS	Yes
MSR2680-XS	Yes

‌

Hardware	Parameter compatibility
MSR2600-12X-WiNet	Yes
MSR2610-13X-WiNet	Yes

‌

destination-port: Distributes traffic based on destination ports.

ingress-port: Distributes traffic based on ingress ports.

The following compatibility matrixes show the support of hardware platforms for this keyword:

Hardware	Parameter compatibility
MSR1008	No
MSR1004-G	Yes
MSR1004-G-5GCN	Yes
MSR2630E-X1	No
MSR3610E-X1, MSR3610E-X1-DP	No
MSR3610-G-X3-DP, MSR3610-G-X3, MSR3610-G-X3-DP-DC, MSR3610-G-X3-DC	No

Hardware	Parameter compatibility
MSR2660-XS	No
MSR2680-XS	No

Hardware	Parameter compatibility
MSR2600-12X-WiNet	No
MSR2610-13X-WiNet	No

‌

ip-protocol: Distributes traffic based on IP protocol types.

The following compatibility matrixes show the support of hardware platforms for this keyword:

Hardware	Parameter compatibility
MSR1008	No
MSR1004-G	Yes
MSR1004-G-5GCN	Yes
MSR2630E-X1	No
MSR3610E-X1, MSR3610E-X1-DP	No
MSR3610-G-X3-DP, MSR3610-G-X3, MSR3610-G-X3-DP-DC, MSR3610-G-X3-DC	No

Hardware	Parameter compatibility
MSR2660-XS	No
MSR2680-XS	No

Hardware	Parameter compatibility
MSR2600-12X-WiNet	No
MSR2610-13X-WiNet	No

‌

mpls-label1: Distributes MPLS traffic based on Layer 1 labels.

source-ip: Distributes traffic based on source IP addresses.

source-mac: Distributes traffic based on source MAC addresses.

The following compatibility matrixes show the support of hardware platforms for this keyword:

Hardware	Parameter compatibility
MSR1008	Yes
MSR1004-G	No
MSR1004-G-5GCN	No
MSR2630E-X1	Yes
MSR3610E-X1, MSR3610E-X1-DP	Yes
MSR3610-G-X3-DP, MSR3610-G-X3, MSR3610-G-X3-DP-DC, MSR3610-G-X3-DC	Yes

‌

Hardware	Parameter compatibility
MSR2660-XS	Yes
MSR2680-XS	Yes

‌

Hardware	Parameter compatibility
MSR2600-12X-WiNet	Yes
MSR2610-13X-WiNet	Yes

‌

source-port: Distributes traffic based on source ports.

vlan-id: Distributes traffic based on VLAN IDs.

The following compatibility matrixes show the support of hardware platforms for this keyword:

Hardware	Parameter compatibility
MSR1008	No
MSR1004-G	Yes
MSR1004-G-5GCN	Yes
MSR2630E-X1	No
MSR3610E-X1, MSR3610E-X1-DP	No
MSR3610-G-X3-DP, MSR3610-G-X3, MSR3610-G-X3-DP-DC, MSR3610-G-X3-DC	No

Hardware	Parameter compatibility
MSR2660-XS	No
MSR2680-XS	No

Hardware	Parameter compatibility
MSR2600-12X-WiNet	No
MSR2610-13X-WiNet	No

‌

Usage guidelines

If you execute this command multiple times, the most recent configuration takes effect.

If an unsupported load sharing mode is set, the device displays an error message.

Examples

# Set the global load sharing mode to load share packets based on destination IP addresses.

<Sysname> system-view

[Sysname] link-aggregation global load-sharing mode destination-ip

Related commands

link-aggregation load-sharing mode

link-aggregation ignore speed

Use link-aggregation ignore speed to configure the system to ignore port speed when it sets the aggregation states of the member ports in an aggregation group.

Use undo link-aggregation ignore speed to restore the default.

Syntax

link-aggregation ignore speed

undo link-aggregation ignore speed

Default

The system does not ignore port speed when it sets the aggregation states of the member ports in an aggregation group.

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Predefined user roles

network-admin

Usage guidelines

IMPORTANT:

Make sure you are fully aware of the impacts of this command when you execute it on a live network.

· When you execute this command or its undo form, the operational key changes and the aggregate interface flaps temporarily.

· This command might cause traffic loss on Selected ports operating at a speed lower than the other Selected ports in the aggregation group when traffic is distributed among the ports.

This command allows ports at a different speed than the reference port to become Selected by ignoring the port speed during operational key calculation.

You must configure the same port speed ignoring setting at the two ends of a static configuration to ensure that the peer ports are placed in the same aggregation state. This requirement does not apply to a dynamic aggregation, on which the two ends negotiate the aggregation state of the peer ports automatically.

Examples

# Configure the system to ignore port speed when it sets the aggregation states of member ports in Layer 2 aggregation group 1.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] link-aggregation ignore speed

link-aggregation lacp traffic-redirect-notification enable

Use link-aggregation lacp traffic-redirect-notification enable to enable link-aggregation traffic redirection.

Use undo link-aggregation lacp traffic-redirect-notification enable to disable link-aggregation traffic redirection.

Syntax

link-aggregation lacp traffic-redirect-notification enable

undo link-aggregation lacp traffic-redirect-notification enable

Default

Link-aggregation traffic redirection is disabled.

Views

System view

Layer 3 aggregate interface view

Predefined user roles

network-admin

Usage guidelines

This feature redirects traffic on a Selected port to the remaining available Selected ports of an aggregation group if one of the following events occurs:

· The port is shut down by using the shutdown command.

NOTE:

The device does not redirect traffic to member ports that become Selected during the traffic redirection process.

This feature ensures zero packet loss for known unicast traffic, but does not protect unknown unicast traffic.

This feature applies only to dynamic link aggregation groups.

To prevent traffic interruption, enable link-aggregation traffic redirection on devices at both ends of the aggregate link.

Global link-aggregation traffic redirection settings take effect on all aggregation groups. A link aggregation group preferentially uses the group-specific link-aggregation traffic redirection settings. If group-specific link-aggregation traffic redirection is not configured, the group uses the global link-aggregation traffic redirection settings.

As a best practice, enable link-aggregation traffic redirection on a per-interface basis. If you enable this feature globally, communication with a third-party peer device might be affected if the peer is not compatible with this feature.

Examples

# Enable link-aggregation traffic redirection.

<Sysname> system-view

[Sysname] link-aggregation lacp traffic-redirect-notification enable

link-aggregation load-sharing mode

Use link-aggregation load-sharing mode to set the link-aggregation load sharing mode for an aggregation group.

Use undo link-aggregation load-sharing mode to restore the default.

Syntax

link-aggregation load-sharing mode { { destination-ip | destination-port | source-ip | source-port } * | bandwidth-usage | per-packet }

undo link-aggregation load-sharing mode

Default

The group-specific load sharing mode is the same as the global load sharing mode.

Views

Layer 3 aggregate interface view

Predefined user roles

network-admin

Parameters

destination-ip: Distributes traffic based on destination IP addresses.

destination-port: Distributes traffic based on destination ports.

source-ip: Distributes traffic based on source IP addresses.

source-port: Distributes traffic based on source ports.

bandwidth-usage: Distributes traffic based on the bandwidth usage of aggregation member ports.

per-packet: Distributes traffic on a per-packet basis.

Usage guidelines

If you execute this command multiple times, the most recent configuration takes effect.

If an unsupported load sharing mode is set, the device displays an error message.

Examples

# Configure Layer 3 aggregation group 1 to load share packets based on destination IP addresses.

<Sysname> system-view

[Sysname] interface route-Aggregation 1

[Sysname-Route-Aggregation1] link-aggregation load-sharing mode destination-ip

Related commands

link-aggregation global load-sharing mode

link-aggregation load-sharing mpls enhanced

Use link-aggregation load-sharing mpls enhanced to enable link-aggregation load sharing enhancement for MPLS packets.

Use undo link-aggregation load-sharing mpls enhanced to disable link-aggregation load sharing enhancement for MPLS packets.

Syntax

link-aggregation load-sharing mpls enhanced

undo link-aggregation load-sharing mpls enhanced

Default

Link-aggregation load sharing enhancement is disabled for MPLS packets.

Views

Layer 3 aggregate interface view

Predefined user roles

network-admin

Usage guidelines

This command enables an aggregate interface to use the IP five-tuple for MPLS packet distribution. The IP five-tuple contains the source IP address, source port number, destination IP address, destination port number, and protocol number.

Use this command only on the provider (P) device. For information about the P device, see MPLS L3VPN configuration in MPLS Configuration Guide.

Examples

# Enable link-aggregation load sharing enhancement for MPLS packets on Route-Aggregation 1.

<Sysname> system-view

[Sysname] interface route-aggregation 1

[Sysname-Route-Aggregation1] link-aggregation load-sharing mpls enhanced

link-aggregation mode

Use link-aggregation mode to set the aggregation mode of an aggregation group.

Use undo link-aggregation mode to restore the default.

Syntax

link-aggregation mode { dynamic | static [ backup ] }

undo link-aggregation mode

Default

An aggregation group operates in static aggregation mode.

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Predefined user roles

network-admin

Parameters

dynamic: Specifies dynamic mode and enables LACP.

static: Specifies static mode.

backup: Specifies static 1+1 backup mode. If you do not specify this keyword, 1+1 backup is not enabled. Only Layer 3 aggregate interfaces support this keyword.

Usage guidelines

When you change the aggregation mode, make sure you understand the impact of the change on services.

Aggregation mode change might cause Selected member ports to become Unselected.

The following restrictions apply to an aggregation group operating in 1+1 backup mode:

· The aggregation group can contain a maximum of two member ports.

· The maximum and minimum limits on the number of Selected ports in the aggregation group do not take effect.

Examples

# Configure Layer 2 aggregation group 1 to operate in dynamic aggregation mode.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] link-aggregation mode dynamic

link-aggregation port-priority

Use link-aggregation port-priority to set the port priority of an interface.

Use undo link-aggregation port-priority to restore the default.

Syntax

link-aggregation port-priority priority

undo link-aggregation port-priority

Default

The port priority of an interface is 32768.

Views

Layer 2 Ethernet interface view

Layer 3 Ethernet interface view

Predefined user roles

network-admin

Parameters

priority: Specifies the port priority in the range of 0 to 65535. The smaller the value, the higher the port priority.

Examples

# Set the port priority to 64 for Layer 2 Ethernet interface GigabitEthernet 0/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 0/0/1

[Sysname-GigabitEthernet0/0/1] link-aggregation port-priority 64

# Set the port priority to 64 for Layer 3 Ethernet interface GigabitEthernet 0/0/2.

<Sysname> system-view

[Sysname] interface gigabitethernet 0/0/2

[Sysname-GigabitEthernet0/0/2] link-aggregation port-priority 64

Related commands

lacp system-priority

link-aggregation primary-port

Use link-aggregation primary-port to assign the primary role to a member port in a 1+1 backup aggregation group.

Use undo link-aggregation primary-port to restore the default.

Syntax

link-aggregation primary-port

undo link-aggregation primary-port

Default

A member port is not assigned the primary role in a 1+1 backup aggregation group.

Views

Layer 3 Ethernet interface view

Predefined user roles

network-admin

Usage guidelines

In a 1+1 backup aggregation group, the primary member port is placed in Selected state to forward all traffic, and the secondary member port is placed in Unselected state as a standby. You can specify a primary member port with this command or let the system to select a primary member port. If you specify a primary member port for a 1+1 backup aggregation group, the aggregation group can revert to the primary member port when that port recovers from failure. As a best practice, use this command to manually specify a primary member port.

If you do not specify a primary member port for an aggregation group, the system acts as follows:

· Assigns the primary role to the reference port if the member ports join the aggregation group simultaneously.

· Assigns the primary role to the member port that first becomes Selected if the member ports join the aggregation group successively.

This command is not available on a port that is not an aggregation group member or is in an aggregation group not operating in 1+1 backup mode.

A 1+1 backup aggregation group can have only one primary member port.

Examples

# Assign the primary role to GigabitEthernet 0/0/1.

<Sysname> system-view

[Sysname] interface gigabitethernet 0/0/1

[Sysname-GigabitEthernet0/0/1] port link-aggregation group 1

[Sysname-GigabitEthernet0/0/1] link-aggregation primary-port

link-aggregation reversion delay

Use link-aggregation reversion delay to set the reversion delay for a 1+1 backup aggregation group.

Use undo link-aggregation reversion delay to restore the default.

Syntax

link-aggregation reversion delay time-value

undo link-aggregation reversion delay

Default

A 1+1 backup aggregation group reverts to the primary member port immediately after that port recovers from failure.

Views

Layer 3 aggregate interface view

Predefined user roles

network-admin

Parameters

time-value: Sets a reversion delay in the range of 1 to 65535 seconds.

Usage guidelines

The reversion delay is the time a 1+1 backup aggregation group must wait before reverting to the primary member port after that port recovers from failure. This timer prevents link flapping from causing frequent primary/secondary member port switchovers.

For this command to take effect on an aggregation group, first configure the aggregation group to operate in 1+1 backup mode and manually specify its primary member port.

Examples

# Set the reversion delay to 5 seconds on Route-Aggregation 1.

<Sysname> system-view

[Sysname] interface route-aggregation 1

[Sysname-Route-Aggregation1] link-aggregation reversion delay 5

Related commands

link-aggregation mode

link-aggregation primary-port

link-aggregation secondary-down

Use link-aggregation secondary-down to configure a 1+1 backup aggregation group to place its secondary member port in down state.

Use undo link-aggregation secondary-down to restore the default.

Syntax

link-aggregation secondary-down

undo link-aggregation secondary-down

Default

In a 1+1 backup aggregation group, the secondary member port is in Unselected state.

Views

Layer 3 aggregate interface view

Predefined user roles

network-admin

Usage guidelines

If the peer for a 1+1 backup aggregation group is unaware of the member port roles, it might send traffic to the secondary member port, and traffic loss occurs consequently. To prevent traffic loss, configure the aggregation group to place its secondary member port in down state. This allows the peer and local ends to use only up ports to transmit traffic.

For this command to take effect on an aggregation group, first configure the aggregation group to operate in 1+1 backup mode.

Examples

# Configure Route-Aggregation 1 to place its secondary member port in down state.

<Sysname> system-view

[Sysname] interface route-aggregation 1

[Sysname-Route-Aggregation1] link-aggregation secondary-down

Related commands

link-aggregation mode

link-aggregation selected-port maximum

Use link-aggregation selected-port maximum to set the maximum number of Selected ports allowed in an aggregation group.

Use undo link-aggregation selected-port maximum to restore the default.

Syntax

link-aggregation selected-port maximum max-number [ lacp-sync ]

undo link-aggregation selected-port maximum

Default

The maximum number of Selected ports allowed in an aggregation group depends on hardware limitation.

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Predefined user roles

network-admin

Parameters

max-number: Specifies the maximum number of Selected ports allowed in an aggregation group. The value range for this argument is 1 to 8.

lacp-sync: Synchronizes the maximum number of Selected ports through LACPDUs. If you do not specify this keyword, the aggregate interface does not synchronize the maximum number of Selected ports with the peer.

Usage guidelines

Executing this command might cause some of the Selected ports in an aggregation group to become Unselected ports.

On a static aggregate link, you must set the maximum number of Selected ports to the same value at its two ends.

On a dynamic aggregate link, you must set the maximum number of Selected ports to the same value at its two ends if you do not specify the lacp-sync keyword. If you specify this keyword, the two ends of the aggregate link compare their maximum Selected port number settings and use the smaller value.

For an aggregation group, the maximum number of Selected ports must be equal to or higher than the minimum number of Selected ports.

The maximum number of Selected ports allowed in an aggregation group is limited by one of the following values, whichever value is smaller:

· Maximum number set by using the link-aggregation selected-port maximum command.

· Maximum number of Selected ports allowed by the link aggregation capability.

You can implement backup between two ports by performing the following tasks:

· Assigning two ports to an aggregation group.

· Setting the maximum number of Selected ports to 1 for the aggregation group.

Then, only one Selected port is allowed in the aggregation group at any point in time, while the Unselected port acts as a backup port.

Examples

# Set the maximum number of Selected ports to 5 for Layer 2 aggregation group 1.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] link-aggregation selected-port maximum 5

Related commands

link-aggregation selected-port minimum

Use link-aggregation selected-port minimum to set the minimum number of Selected ports in an aggregation group.

Use undo link-aggregation selected-port minimum to restore the default.

Syntax

link-aggregation selected-port minimum min-number

undo link-aggregation selected-port minimum

Default

The minimum number of Selected ports in an aggregation group is not specified.

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Predefined user roles

network-admin

Parameters

min-number: Specifies the minimum number of Selected ports in an aggregation group required to bring up the aggregate interface. The value range for this argument is 1 to 8.

Usage guidelines

Executing this command might cause all member ports in the aggregation group to become Unselected ports.

The minimum number of Selected ports allowed in the aggregation groups must be the same for the local and peer ends.

For an aggregation group, the minimum number of Selected ports must be equal to or lower than the maximum number of Selected ports.

Examples

# Set the minimum number of Selected ports to 3 for Layer 2 aggregation group 1.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] link-aggregation selected-port minimum 3

Related commands

link-aggregation selected-port maximum

link-aggregation selected-port minimum percentage

Use link-aggregation selected-port minimum percentage to set the minimum percentage of Selected ports in an aggregation group.

Use undo link-aggregation selected-port minimum percentage to restore the default.

Syntax

link-aggregation selected-port minimum percentage number

undo link-aggregation selected-port minimum percentage

Default

The minimum percentage of Selected ports is not set for an aggregation group.

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Predefined user roles

network-admin

Parameters

number: Specifies the minimum percentage of Selected ports. The value range for this argument is 1 to 100.

Usage guidelines

CAUTION:

After you execute this command, aggregate interface flapping might occur when ports join or leave an aggregation group. Make sure you are fully aware of the impacts of this command when you execute it on a live network.

You must set the same minimum percentage of Selected ports at the two ends of an aggregate link.

The minimum number of Selected ports in an aggregation group equals the higher one of the following values:

· The number of member ports in the aggregation group multiplied by the minimum percentage of Selected ports.

· The limit set by using the link-aggregation selected-port minimum command.

Examples

# Set the minimum percentage of Selected ports to 50% for Layer 2 aggregate interface Bridge-Aggregation 1.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] link-aggregation selected-port minimum percentage 50

# Set the minimum percentage of Selected ports to 50% for Layer 3 aggregate interface Route-Aggregation 1.

<Sysname> system-view

[Sysname] interface route-aggregation 1

[Sysname-Route-Aggregation1] link-aggregation selected-port minimum percentage 50

Related commands

link-aggregation selected-port minimum

link-aggregation switchover

Use link-aggregation switchover to perform a primary/secondary member port switchover in a 1+1 backup aggregation group.

Syntax

link-aggregation switchover

Views

Layer 3 aggregate interface view

Predefined user roles

network-admin

Usage guidelines

CAUTION:

This command might cause traffic loss. Make sure you are fully aware of the impacts of this command when you execute it on a live network.

Use this command to switch member port roles for a 1+1 backup aggregation group whose primary member port is set by the system when the state of peer ports changes.

If the link-aggregation secondary-down command has been executed for the aggregation group, the link-aggregation switchover command brings up the down secondary member port for it to take over the primary role.

Before you execute the link-aggregation switchover command for a 1+1 backup aggregation group, verify that the following requirements are met:

· The aggregation group contains one Selected port and one Unselected port.

· The primary member port is set by the system.

· The secondary member port can become Selected.

Examples

# Perform a primary/secondary member port switchover in the aggregation group of Route-Aggregation 1.

<Sysname> system-view

[Sysname] interface route-aggregation 1

[Sysname-Route-Aggregation1] link-aggregation switchover

This operation will change the current link status. Continue? [Y/N]:

Related commands

link-aggregation mode

link-aggregation primary-port

mtu

Use mtu to set the MTU of a Layer 3 aggregate interface or subinterface.

Use undo mtu to restore the default.

Syntax

mtu size

undo mtu

Default

The MTU of Layer 3 aggregate interfaces and subinterfaces is 1500 bytes.

Views

Layer 3 aggregate interface view

Layer 3 aggregate subinterface view

Predefined user roles

network-admin

Parameters

size: Specifies an MTUin bytes. The value range for this argument is 46 to 1650..

Examples

# Set the MTU of interface Route-Aggregation 1 to 1430 bytes.

<Sysname> system-view

[Sysname] interface route-aggregation 1

[Sysname-Route-Aggregation1] mtu 1430

Related commands

display interface

port lacp system-mac

Use port lacp system-mac to set the LACP system MAC address on an aggregate interface.

Use undo port lacp system to restore the default.

Syntax

port lacp system-mac mac-address

undo port lacp system-mac

Default

The LACP system MAC address is the bridge MAC address of the device.

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Predefined user roles

network-admin

Parameters

mac-address: Specifies a MAC address in the format of H-H-H. The MAC address cannot be an all-zero or all-F MAC address.

Usage guidelines

Member devices in an S-MLAG system must use the same LACP system MAC address.

Examples

# Set the LACP system MAC address to 0002-0002-0002 on an aggregate interface.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] port lacp system-mac 2-2-2

Related commands

display link-aggregation verbose

lacp system-mac

port lacp system-priority

Use port lacp system-priority to set the LACP system priority on an aggregate interface.

Use undo port lacp system-priority to restore the default.

Syntax

port lacp system-priority priority

undo port lacp system-priority

Default

The LACP system priority is 32768.

Views

Layer 2 aggregate interface view

Layer 3 aggregate interface view

Predefined user roles

network-admin

Parameters

priority: Specifies the LACP system priority in the range of 0 to 65535. The smaller the value, the higher the LACP system priority.

Usage guidelines

Member devices in an S-MLAG system must use the same LACP system priority.

Examples

# Set the LACP system priority to 32 on an aggregate interface.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] port lacp system-priority 32

Related commands

display link-aggregation verbose

lacp system-priority

port link-aggregation group

Use port link-aggregation group to assign an interface to an aggregation group.

Use undo port link-aggregation group to remove an interface from the aggregation group to which it belongs.

Syntax

port link-aggregation group { group-id [ force ] | auto [ group-id ] }

undo port link-aggregation group

Default

An interface does not belong to any aggregation group.

Views

Layer 2 Ethernet interface view

Layer 3 Ethernet interface view

Layer 3 Ethernet subinterface view

Predefined user roles

network-admin

Parameters

group-id: Specifies an aggregation group by its aggregate interface number. The value range for the number argument is 1 to 8.

force: Enables the current interface to synchronize attribute configurations from the aggregate interface. If you do not specify this keyword, the current interface does not synchronize attribute configurations from the aggregate interface when it joins the aggregation group. This keyword is supported only on Layer 2 Ethernet interfaces.

auto: Enables automatic assignment.

Usage guidelines

A Layer 2 Ethernet interface can be assigned only to a Layer 2 aggregation group. A Layer 3 Ethernet interface or subinterface can be assigned only to a Layer 3 aggregation group.

An interface can belong to only one aggregation group.

An interface cannot join an aggregation group if it has different attribute configurations from the aggregate interface. After joining an aggregation group, an interface inherits the attribute configurations on the aggregate interface. You can modify the attribute configurations only on the aggregate interface.

The force keyword takes effect only when you assign the interface to an aggregation group. It cannot be saved in the running configuration or a configuration file.

By default, you cannot assign both Ethernet interfaces and Ethernet subinterfaces to the aggregation group. You cannot create subinterfaces on an Ethernet interface that is in the aggregation group. You cannot assign an Ethernet interface that has subinterfaces to the aggregation group.

You cannot create aggregate subinterfaces on an aggregate interface if its aggregation group contains Ethernet subinterfaces. You cannot assign Ethernet subinterfaces to an aggregation group if its aggregate interface has aggregate subinterfaces.

Automatic assignment is available only on Layer 2 and Layer 3 Ethernet interfaces.

When you enable automatic assignment, you can specify a preferred aggregation group, which must be in dynamic mode.

The device assigns the interface to the preferred aggregation group as long as the LACPDUs received on the interface match the peer information of the reference port in the group.

If you do not specify a preferred group or if the preferred group match fails, the device attempts to select a matching group from the existing dynamic aggregation groups. If no match is found, the device creates a dynamic aggregation group based on the LACPDUs and assigns the interface to that aggregation group.

As a best practice, do not modify the configuration on an automatically created aggregate interface or its member ports.

As a best practice, do not configure both manual member port assignment and automatic member port assignment. If you do that, a port might be assigned to different aggregation groups, causing the member port to fail to be selected.

Examples

# Assign Layer 2 Ethernet interface GigabitEthernet 0/0/1 to Layer 2 aggregation group 1.

<Sysname> system-view

[Sysname] interface gigabitethernet 0/0/1

[Sysname-GigabitEthernet0/0/1] port link-aggregation group 1

# Assign Layer 3 Ethernet interface GigabitEthernet 0/0/2 to Layer 3 aggregation group 2.

<Sysname> system-view

[Sysname] interface gigabitethernet 0/0/2

[Sysname-GigabitEthernet0/0/2] port link-aggregation group 2

port s-mlag group

Use port s-mlag group to assign an aggregate interface to an S-MLAG group.

Use undo port s-mlag group to restore the default.

Syntax

port s-mlag group group-id

undo port s-mlag group

The following compatibility matrixes show the support of hardware platforms for this command:

Hardware	Command compatibility
MSR1008	Yes
MSR1004-G	No
MSR1004-G-5GCN	No
MSR2630E-X1	Yes
MSR3610E-X1, MSR3610E-X1-DP	Yes
MSR3610-G-X3-DP, MSR3610-G-X3, MSR3610-G-X3-DP-DC, MSR3610-G-X3-DC	No

‌

Hardware	Command compatibility
MSR2660-XS	Yes
MSR2680-XS	Yes

‌

Hardware	Command compatibility
MSR2600-12X-WiNet	Yes
MSR2610-13X-WiNet	Yes

‌

Default

An aggregate interface is not in any S-MLAG group.

Views

Layer 2 aggregate interface view

Predefined user roles

network-admin

Parameters

group-id: Specifies an S-MLAG group number in the range of 1 to 1024.

Usage guidelines

You can assign only Layer 2 aggregate interfaces in dynamic mode to an S-MLAG group.

Each S-MLAG group can contain only one aggregate interface on each device.

Examples

# Assign Bridge-Aggregation 1 to S-MLAG group 1.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] port s-mlag group 1

reset lacp statistics

Use reset lacp statistics to clear LACP statistics for the specified link aggregation member ports.

Syntax

reset lacp statistics [ interface interface-list ]

Views

User view

Predefined user roles

network-admin

Parameters

interface interface-list: Specifies a list of link aggregation member ports, in the format interface-type interface-number1 [ to interface-type interface-number2 ]. The value for the interface-number1 argument must be equal to or greater than the value for the interface-number2 argument. If you do not specify any member ports, the command clears LACP statistics for all member ports.

Examples

# Clear LACP statistics for all link aggregation member ports.

<Sysname> reset lacp statistics

Related commands

display link-aggregation member-port

sub-interface rate-statistic

Use sub-interface rate-statistic to enable rate statistics collection for the subinterfaces of a Layer 3 aggregate interface.

Use undo sub-interface rate-statistic to disable rate statistics collection for the subinterfaces of a Layer 3 aggregate interface.

Syntax

sub-interface rate-statistic

undo sub-interface rate-statistic

Default

Rate statistics collection is disabled for Layer 3 aggregate subinterfaces.

Views

Layer 3 aggregate interface view

Predefined user roles

network-admin

Usage guidelines

Rate statistics collection for Layer 3 aggregate subinterfaces is resource intensive. When you use this feature on a live network, make sure you fully understand its impact.

This command enables the device to periodically refresh rate statistics for the subinterfaces of a Layer 3 aggregate interface. The rate statistics are available in two statistics polling intervals after you execute this command. To set the statistics polling interval, use the flow-interval command.

Examples

# Enable rate statistics collection for the subinterfaces of Route-Aggregation 1.

<Sysname> system-view

[Sysname] interface route-aggregation 1

[Sysname-Route-Aggregation1] sub-interface rate-statistic

This configuration may make a negative effect on the performance. Are you sure to continue? [Y/N]:y

The configuration will take effect after 2 flow intervals.

Related commands

flow-interval (Interface Command Reference)

05-Layer 2—LAN Switching Command Reference

display link-aggregation verbose

interface bridge-aggregation

interface route-aggregation

link-aggregation port-priority

port s-mlag group

Intelligent Terminal Products

Product Support Services

Technical Service Solutions

Resource Center

Policy

Online Help

Become a Partner

Partner Policy & Program

Global Learning

Partner Sales Resources

Service Business

News & Events

Contact Us