Login
- Table of Contents
-
- 01-Fundamentals Command Reference
- 00-Preface
- 01-CLI commands
- 02-Login management commands
- 03-RBAC commands
- 04-FTP and TFTP commands
- 05-File system management commands
- 06-Configuration file management commands
- 07-Software upgrade commands
- 08-ISSU commands
- 09-Emergency shell commands
- 10-Device management commands
- 11-Tcl commands
- 12-Python commands
- 13-License management commands
- 14-Preprovisioning commands
- Related Documents
-
| Title | Size | Download |
|---|---|---|
| 02-Login management commands | 147.72 KB |
Login management commands
The device supports the FIPS mode that complies with NIST FIPS 140-2 requirements. Support for features, commands, and parameters might differ in FIPS mode and non-FIPS mode. For more information about FIPS mode, see Security Configuration Guide.
Some login management commands are available in both user line view and user line class view. For these commands, the device uses the following rules to determine the settings to be activated:
· A setting in user line view is applied only to the user line. A setting in user line class view is applied to all user lines of the class.
· A non-default setting in either view takes precedence over a default setting in the other view. A non-default setting in user line view takes precedence over a non-default setting in user line class view.
· A setting in user line view takes effect immediately and affects the online user. A setting in user line class view does not affect online users. It takes effect only for new login users.
activation-key
Use activation-key to define a shortcut key for starting a terminal session.
Use undo activation-key to restore the default.
Syntax
activation-key key-string
undo activation-key
Default
Pressing Enter starts a terminal session.
Views
User line view, user line class view
Predefined user roles
network-admin
Parameters
key-string: Specifies the shortcut key. It can be a character (case sensitive), or an ASCII code value in the range of 0 to 127. For example, activation-key 65 defines the shortcut key A. If you configure activation-key a, the shortcut key is a.
Usage guidelines
This command is not supported in VTY line view or VTY line class view.
This command is available in both user line view and user line class view. A non-default setting in either view takes precedence over a default setting in the other view. A non-default setting in user line view takes precedence over a non-default setting in user line class view.
To display the shortcut key you have defined, use the display current-configuration | include activation-key command.
Examples
# Configure character s as the shortcut key for starting a terminal session on the AUX line.
<Sysname> system-view
[Sysname] line aux 0
[Sysname-line-aux0] activation-key s
To verify the configuration:
1. Exit the console session.
[Sysname-line-aux0] return
<Sysname> quit
2. Log in again through the AUX line.
The following message appears:
Press ENTER to get started.
3. Press Enter.
Pressing Enter does not start a session.
4. Enter s.
A terminal session is started.
<Sysname>
authentication-mode
Use authentication-mode to set the authentication mode for a user line.
Use undo authentication-mode to restore the default.
Syntax
In non-FIPS mode:
authentication-mode { none | password | scheme }
undo authentication-mode
In FIPS mode:
authentication-mode scheme
undo authentication-mode
Default
In non-FIPS mode, the authentication mode is password for VTY lines, and none for the AUX lines.
In FIPS mode, the authentication mode is scheme.
Views
User line view, user line class view
Predefined user roles
network-admin
Parameters
none: Disables authentication.
password: Performs local password authentication.
scheme: Performs AAA authentication. For more information about AAA, see Security Configuration Guide.
Usage guidelines
When the authentication mode is none, a user can log in without authentication. To improve device security, use the password or scheme authentication mode.
In VTY line view, this command is associated with the protocol inbound command. If you specify a non-default value for only one of the two commands in VTY line view, the other command uses the default setting, regardless of the setting in VTY line class view.
Examples
# Enable the none authentication mode for user line VTY 0.
<Sysname> system-view
[Sysname] line vty 0
[Sysname-line-vty0] authentication-mode none
# Enable password authentication for user line VTY 0 and set the password to 321.
<Sysname> system-view
[Sysname] line vty 0
[Sysname-line-vty0] authentication-mode password
[Sysname-line-vty0] set authentication password simple 321
# Enable scheme authentication for user line VTY 0. Configure local user 123 and set the password to 321. Assign the Telnet service and the user role network-admin to the user.
<Sysname> system-view
[Sysname] line vty 0
[Sysname-line-vty0] authentication-mode scheme
[Sysname-line-vty0] quit
[Sysname] local-user 123
[Sysname-luser-manage-123] password simple 321
[Sysname-luser-manage-123] service-type telnet
[Sysname-luser-manage-123] authorization-attribute user-role network-admin
Related commands
set authentication password
auto-execute command
|
|
CAUTION: After configuring this command for a user line, you might be unable to access the CLI through the user line. Make sure you can access the CLI through a different user line before you configure this command and save the configuration. |
Use auto-execute command to specify a command that is automatically executed when a user logs in through the current user line.
Use undo auto-execute command to remove the configuration.
Syntax
auto-execute command command
undo auto-execute command
Default
Command auto-execution is disabled.
Views
User line view, user line class view
Predefined user roles
network-admin
Parameters
command: Specifies the command to be automatically executed.
Usage guidelines
This command is not supported in AUX line view or AUX line class view.
This command is available in both user line view and user line class view. A non-default setting in either view takes precedence over a default setting in the other view. A non-default setting in user line view takes precedence over a non-default setting in user line class view.
The device automatically executes the specified command when a user logs in through the user line, and closes the user connection after the command is executed. If the command triggers another task, the device does not close the user connection until the task is completed.
Typically, you configure the auto-execute command telnet X.X.X.X command on the device so the device redirects a Telnet user to the host at X.X.X.X. In this case, the connection to the current device is closed when the user terminates the Telnet connection to X.X.X.X.
Examples
# Configure the device to automatically Telnet to 192.168.1.41 after a user logs in through user line VTY 0.
<Sysname> system-view
[Sysname] line vty 0
[Sysname-line-vty0] auto-execute command telnet 192.168.1.41
% This action will lead to configuration failure through line-vty0. Are you sure?
[Y/N]:y
[Sysname-line-vty0]
# To verify the configuration, Telnet to 192.168.1.40.
The device automatically Telnets to 192.168.1.41, and the following output is displayed:
C:\> telnet 192.168.1.40
******************************************************************************
* Copyright (c) 2004-2017 New H3C Technologies Co., Ltd. All rights reserved.*
* Without the owner's prior written consent, *
* no decompiling or reverse-engineering shall be allowed. *
******************************************************************************
Trying 192.168.1.41 ...
Press CTRL+K to abort
Connected to 192.168.1.41 ...
******************************************************************************
* Copyright (c) 2004-2017 New H3C Technologies Co., Ltd. All rights reserved.*
* Without the owner's prior written consent, *
* no decompiling or reverse-engineering shall be allowed. *
******************************************************************************
<Sysname.41>
This operation is the same as directly logging in to the device at 192.168.1.41 through Telnet. When you break the Telnet connection to 192.168.1.41, the Telnet connection to 192.168.1.40 is broken at the same time.
command accounting
Use command accounting to enable command accounting.
Use undo command accounting to restore the default.
Syntax
command accounting
undo command accounting
Default
Command accounting is disabled, and the accounting server does not record executed commands.
Views
User line view, user line class view
Predefined user roles
network-admin
Usage guidelines
When command accounting is enabled but command authorization is not, every executed command is recorded on the HWTACACS server.
When both command accounting and command authorization are enabled, only authorized commands that are executed are recorded on the HWTACACS server.
Invalid commands issued by users are not recorded.
If the command accounting command is configured in user line class view, command accounting is enabled on all user lines in the class. You cannot configure the undo command accounting command in the view of a user line in the class.
Examples
# Enable command accounting for user line VTY 0.
<Sysname> system-view
[Sysname] line vty 0
[Sysname-line-vty0] command accounting
Related commands
· accounting command (Security Command Reference)
· command authorization
command authorization
Use command authorization to enable command authorization.
Use undo command authorization to restore the default.
Syntax
command authorization
undo command authorization
Default
Command authorization is disabled. Logged-in users can execute commands without authorization.
Views
User line view, user line class view
Predefined user roles
network-admin
Usage guidelines
When command authorization is enabled, a command is available only if the following requirements are met:
· The user has the commensurate user role.
· The user is authorized to use the command by the AAA scheme.
If the command authorization command is configured in user line class view, command authorization is enabled on all user lines in the class. You cannot configure the undo command authorization command in the view of a user line in the class.
Examples
# Enable command accounting for VTY 0 so the VTY 0 user can execute only authorized commands that are permitted by the user role.
<Sysname> system-view
[Sysname] line vty 0
[Sysname-line-vty0] command authorization
Related commands
· authorization command (Security Command Reference)
· command accounting
databits
Use databits to specify the number of data bits for each character.
Use undo databits to restore the default.
Syntax
databits { 5 | 6 | 7 | 8 }
undo databits
Default
Eight data bits are used for each character.
Views
User line view
Predefined user roles
network-admin
Parameters
5: Uses five data bits for each character.
6: Uses six data bits for each character.
7: Uses seven data bits for each character.
8: Uses eight data bits for each character.
Usage guidelines
This command is not supported in VTY line class view.
This setting must be the same as that on the configuration terminal.
Examples
# Configure AUX 0 to use five data bits for each character.
<Sysname> system-view
[Sysname] line aux 0
[Sysname-line-aux0] databits 5
display line
Use display line to display user line information.
Syntax
display line [ number1 | { aux | vty } number2 ] [ summary ]
Views
Any view
Predefined user roles
network-admin
network-operator
Parameters
number1: Specifies the absolute number of a user line, in the range of 0 to 192.
aux: Specifies the AUX line.
vty: Specifies the VTY line.
number2: Specifies the relative number of a user line. The value range is 0 to 128 for the AUX line and 0 to 63 for the VTY line.
summary: Displays summary information about user lines. If you do not specify this keyword, the detailed information is displayed.
Examples
# Display user line information.
<Sysname> display line 0
Idx Type Tx/Rx Modem Auth Int
0 AUX 0 9600 - N -
+ : Line is active.
F : Line is active and in async mode.
Idx : Absolute index of line.
Type : Type and relative index of line.
Auth : Login authentication mode.
Int : Physical port of the line.
A : Authentication use AAA.
N : No authentication is required.
P : Password authentication.
Table 1 Command output
|
Field |
Description |
|
Modem |
Whether the modem allows calling in or out. By default, this attribute is not configured and a hyphen (-) is displayed. |
# Display summary information about all user lines.
<Sysname> display line summary
Line type : [AUX]
0:UXXX XXXX XXXX XXXX
…
112:XXXX XXXX XXXX XXXX
Line type : [VTY]
129:UUXX XXXX XXXX XXXX
…
176:XXXX XXXX XXXX XXXX
3 lines used. (U)
190 lines not used. (X)
Table 2 Command output
|
Fields |
Description |
|
number:status |
The number indicates the absolute number of the first user line of the user line class, starting from 0. The status indicates whether the user lines of the user line class are being used (X for unused and U for used). For example, if "0:UXXX XXXX XXXX XXXX" is displayed, there are ten user lines of the user line class, which use the absolute numbers 0 through 15. User line 0 is being used. The other user lines are not. |
display telnet client
Use display telnet client to display the source address or interface for outgoing Telnet packets when the device acts as a Telnet client.
Syntax
display telnet client
Views
Any view
Predefined user roles
network-admin
network-operator
Examples
# Display the Telnet client configuration of the device when it acts as a Telnet client.
<Sysname> display telnet client
The source IP address is 1.1.1.1.
The output shows that the device uses the source IPv4 address 1.1.1.1 for outgoing Telnet packets when it acts as a Telnet client.
Related commands
telnet client source
display user-interface
Use display user-interface to display user line information.
Syntax
display user-interface [ number1 | { aux | vty } number2 ] [ summary ]
Views
Any view
Predefined user roles
network-admin
network-operator
Parameters
number1: Specifies the absolute number of a user line, in the range of 0 to 192.
aux: Specifies the AUX line.
vty: Specifies the VTY line.
number2: Specifies the relative number of a user line. The value range is 0 to 128 for the AUX line and 0 to 63 for the VTY line.
summary: Displays summary information about user lines. If you do not specify this keyword, the detailed information is displayed.
Usage guidelines
This command is an older version reserved for backward compatibility purposes. As a best practice, use the display line command.
Examples
# Display user line information.
<Sysname> display user-interface 0
Idx Type Tx/Rx Modem Auth Int
0 AUX 0 9600 - N -
+ : Line is active.
F : Line is active and in async mode.
Idx : Absolute index of line.
Type : Type and relative index of line.
Auth : Login authentication mode.
Int : Physical port of the line.
A : Authentication use AAA.
N : No authentication is required.
P : Password authentication.
Table 3 Command output
|
Field |
Description |
|
Modem |
Whether the modem allows calling in or out. By default, this attribute is not configured and a hyphen (-) is displayed. |
# Display summary information about all user lines.
<Sysname> display user-interface summary
Line type : [AUX]
0:UXXX XXXX XXXX XXXX
…
112:XXXX XXXX XXXX XXXX
Line type : [VTY]
129:UUXX XXXX XXXX XXXX
…
176:XXXX XXXX XXXX XXXX
3 lines used. (U)
190 lines not used. (X)
Table 4 Command output
|
Fields |
Description |
|
number:status |
The number indicates the absolute number of the first user line of the user line class, starting from 0. The status indicates whether the user lines of the user line class are being used (X for unused and U for used). For example, if "0:UXXX XXXX XXXX XXXX" is displayed, there are ten user lines of the user line class, which use the absolute numbers 0 through 15. User line 0 is being used. The other user lines are not. |
display users
Use display users to display online CLI user information.
Syntax
display users [ all ]
Views
Any view
Predefined user roles
network-admin
network-operator
Parameters
all: Displays all user lines supported by the device.
Examples
# Display online user information.
<Sysname> display users
Idx Line Idle Time Pid Type
129 VTY 0 00:10:49 Jun 11 11:27:32 320 TEL
+ 130 VTY 1 00:00:00 Jun 11 11:39:40 334 TEL
Following are more details.
VTY 0 :
Location: 192.168.1.12
VTY 1 :
Location: 192.168.1.26
+ : Current operation user.
F : Current operation user works in async mode.
The output shows that two users have logged in to the device: one is using user line VTY 0 and the other (yourself) is using VTY 1. Your IP address is 192.168.1.26.
Table 5 Command output
|
Field |
Description |
|
Idx |
Absolute number of the user line. |
|
Line |
Type and relative number of the user line. |
|
Idle |
Time elapsed after the user's most recent input, in the format hh:mm:ss. |
|
Time |
Login time of the user. |
|
Pid |
Process ID of the user session. |
|
Type |
User type, such as Telnet, SSH. |
|
+ |
Indicates the user line you are using. |
|
Location |
IP address of the user. |
escape-key
Use escape-key to define a shortcut key for terminating a task.
Use undo escape-key to disable the shortcut key for terminating a task.
Syntax
escape-key { key-string| default }
undo escape-key
Default
Pressing Ctrl+C terminates a task.
Views
User line view, user line class view
Predefined user roles
network-admin
Parameters
key-string: Specifies the shortcut key. It can be a character, or an ASCII code value in the range of 0 to 127. For example, escape-key 65 defines the shortcut key A. If you configure escape-key a, the shortcut key is a.
default: Restores the default escape key sequence Ctrl+C.
Usage guidelines
Some commands might take a long time to complete in certain situations. Examples include:
· A ping command that has 1000 packets to send.
· A tracert command that is used for an unreachable destination.
To stop a command, press the shortcut key for terminating tasks.
Whether a command can be terminated by Ctrl+C by default depends on the software implementation of the command. For more information, see the description of the command.
As a best practice, use a key sequence as the shortcut key. If you define a single character as the shortcut key, pressing the key while a command is being executed stops the command. If no command is being executed, the result depends on the following situations:
· If you are managing the local device, pressing the key enters the character as a common character.
· If you Telnet to another device and manage the remote device, pressing the key does nothing.
You can execute this command multiple times, but only the most recent configuration takes effect. To view the current shortcut key definition, use the display current-configuration command.
This command is available in both user line view and user line class view. A non-default setting in either view takes precedence over a default setting in the other view. A non-default setting in user line view takes precedence over a non-default setting in user line class view.
Examples
# Define character a as the shortcut key for terminating a task.
<Sysname> system-view
[Sysname] line aux 0
[Sysname-line-aux0] escape-key a
To verify the configuration:
1. Ping IP address 192.168.1.49, specifying the -c keyword to set the number of ICMP echo request packets to 20.
<Sysname> ping -c 20 192.168.1.49
PING 192.168.1.49: 56 data bytes, press a to break
Reply from 192.168.1.49: bytes=56 Sequence=1 ttl=255 time=3 ms
Reply from 192.168.1.49: bytes=56 Sequence=2 ttl=255 time=3 ms
2. Press a.
The task is terminated, and the system returns to user view.
--- 192.168.1.49 ping statistics ---
2 packet(s) transmitted
2 packet(s) received
0.00% packet loss
round-trip min/avg/max = 3/3/3 ms
<Sysname>
flow-control
Use flow-control to configure the flow control mode.
Use undo flow-control to restore the default.
Syntax
flow-control { hardware | none | software }
undo flow-control
Default
The flow control mode is none.
Views
User line view
Predefined user roles
network-admin
Parameters
hardware: Performs hardware flow control.
none: Disables flow control.
software: Performs software flow control.
Usage guidelines
This command is not supported in VTY line view.
The device supports flow control in both the inbound and outbound directions.
· For flow control in the inbound direction, the local device listens to flow control information from the remote device.
· For flow control in the outbound direction, the local device sends flow control information to the remote device.
The flow control setting takes effect in both directions.
To communicate, two devices must be configured with the same flow control mode.
Examples
# Configure software flow control in the inbound and outbound directions for user line AUX 0.
<Sysname> system-view
[Sysname] line aux 0
[Sysname-line-aux0] flow-control software
free line
Use free line to release a user line.
Syntax
free line { number1 | { aux | vty } number2 }
Views
User view
Predefined user roles
network-admin
Parameters
number1: Specifies the absolute number of a user line, in the range of 0 to 192.
aux: Specifies the AUX line.
vty: Specifies the VTY line.
number2: Specifies the relative number of a user line. The value range is 0 to 128 for the AUX line and 0 to 63 for the VTY line.
Usage guidelines
This command does not release the line you are using.
Examples
# Release user line VTY 1:
1. Display online users.
<Sysname> display users
Idx Line Idle Time Pid Type
129 VTY 0 00:10:49 Jun 11 11:27:32 320 TEL
+ 130 VTY 1 00:00:00 Jun 11 11:39:40 334 TEL
Following are more details.
VTY 0 :
Location: 192.168.1.12
VTY 1 :
Location: 192.168.1.26
+ : Current operation user.
F : Current operation user works in async mode.
2. If the operations of the user on VTY 1 impact your operations, log out the user.
<Sysname> free line vty 1
Are you sure to free line vty1? [Y/N]:y
[OK]
free user-interface
Use free user-interface to release a user line.
Syntax
free user-interface { number1 | { aux | vty } number2 }
Views
User view
Predefined user roles
network-admin
Parameters
number1: Specifies the absolute number of a user line, in the range of 0 to 192.
aux: Specifies the AUX line.
vty: Specifies the VTY line.
number2: Specifies the relative number of a user line. The value range is 0 to 128 for the AUX line and 0 to 63 for the VTY line.
Usage guidelines
This command does not release the line you are using.
This command is an older version reserved for backward compatibility purposes. As a best practice, use the free line command.
Examples
# Release user line VTY 1:
1. Display online users.
<Sysname> display users
Idx LINE Idle Time Pid Type
129 VTY 0 00:10:49 Jun 11 11:27:32 320 TEL
+ 130 VTY 1 00:00:00 Jun 11 11:39:40 334 TEL
Following are more details.
VTY 0 :
Location: 192.168.1.12
VTY 1 :
Location: 192.168.1.26
+ : Current operation user.
F : Current operation user works in async mode.
2. If the operations of the user on VTY 1 impact your operations, log out the user.
<Sysname> free user-interface vty 1
Are you sure to free line vty1? [Y/N]:y
[OK]
history-command max-size
Use history-command max-size to set the size of the command history buffer for a user line.
Use undo history-command max-size to restore the default.
Syntax
history-command max-size size-value
undo history-command max-size
Default
The buffer of a user line saves up to 10 history commands.
Views
User line view, user line class view
Predefined user roles
network-admin
Parameters
size-value: Specifies the maximum number of history commands the buffer can store, in the range of 0 to 256.
Usage guidelines
Each user line uses a separate command history buffer to save commands successfully executed by its user. The size of the buffer determines how many history commands the buffer can store.
To view stored history commands on your user line, press the up or down arrow key, or execute the display history-command command.
Terminating a CLI session clears the commands in the history buffer.
This command is available in both user line view and user line class view. A non-default setting in either view takes precedence over a default setting in the other view. A non-default setting in user line view takes precedence over a non-default setting in user line class view.
Examples
# Set the size of the command history buffer to 20 for user line AUX 0.
<Sysname> system-view
[Sysname] line aux 0
[Sysname-line-aux0] history-command max-size 20
idle-timeout
Use idle-timeout to set the CLI connection idle-timeout timer.
Use undo idle-timeout to restore the default.
Syntax
idle-timeout minutes [ seconds ]
undo idle-timeout
Default
The CLI connection idle-timeout timer is 10 minutes.
Views
User line view, user line class view
Predefined user roles
network-admin
Parameters
minutes: Specifies the number of minutes for the timer, in the range of 0 to 35791. The default is 10 minutes.
seconds: Specifies the number of seconds for the timer, in the range of 0 to 59. The default is 0 seconds.
Usage guidelines
The system automatically terminates a user connection if no information interaction occurs on the connection within the idle-timeout interval.
Setting the CLI connection idle-timeout timer to 0 disables the idle-timeout feature.
This command is available in both user line view and user line class view. A non-default setting in either view takes precedence over a default setting in the other view. A non-default setting in user line view takes precedence over a non-default setting in user line class view.
Examples
# Set the CLI connection idle-timeout timer to 1 minute and 30 seconds for user line AUX 0.
<Sysname> system-view
[Sysname] line aux 0
[Sysname-line-aux0] idle-timeout 1 30
line
Use line to enter one or multiple user line views.
Syntax
line { first-number1 [ last-number1 ] | { aux | vty } first-number2 [ last-number2 ] }
Views
System view
Predefined user roles
network-admin
Parameters
first-number1: Specifies the absolute number of the first user line, in the range of 0 to 192.
last-number1: Specifies the absolute number of the last user line. This number cannot be smaller than first-number1.
aux: Specifies the AUX line.
vty: Specifies the VTY line.
first-number2: Specifies the relative number of the first user line. The value range is 0 to 128 for the AUX line and 0 to 63 for the VTY line.
last-number2: Specifies the relative number of the last user line. This number cannot be smaller than first-number2.
Usage guidelines
To configure settings for a single user line, use this command to enter the user line view.
To configure the same settings for multiple user lines, use this command to enter multiple user line views.
Examples
# Enter the view of user line AUX 0.
<Sysname> system-view
[Sysname] line aux 0
[Sysname-line-aux0]
# Enter the views of user lines VTY 0 to VTY 4.
<Sysname> system-view
[Sysname] line vty 0 4
[Sysname-line-vty0-4]
Related commands
line class
line class
Use line class to enter user line class view.
Syntax
line class { aux | vty }
Views
System view
Predefined user roles
network-admin
Parameters
aux: Specifies the AUX line class view.
vty: Specifies the VTY line class view.
Usage guidelines
To configure the same settings for all user lines of a line class, use this command to enter the user line class view.
Some login management commands are available in both user line view and user line class view. For these commands, the device uses the following rules to determine the settings to be activated:
· A setting in user line view is applied only to the user line. A setting in user line class view is applied to all user lines of the class.
· A non-default setting in either view takes precedence over a default setting in the other view. A non-default setting in user line view takes precedence over a non-default setting in user line class view.
· A setting in user line view takes effect immediately and affects the online user. A setting in user line class view takes effect only for new login users. It does not affect online users.
Examples
# Set the CLI connection idle-timeout timer to 15 minutes in VTY line class view.
<Sysname> system-view
[Sysname] line class vty
[Sysname-line-class-vty] idle-timeout 15
# In AUX line class view, configure character s as the shortcut key for starting a terminal session.
<Sysname> system-view
[Sysname] line class aux
[Sysname-line-class-aux] activation-key s
[Sysname-line-class-aux] quit
# In AUX line view, restore the default shortcut key for starting a terminal session.
[Sysname] line aux 0
[Sysname-line-aux0] undo activation-key
Alternatively:
[Sysname-line-aux0] activation-key 13
To verify the configuration:
1. Exit the console session.
[Sysname-line-aux0] return
<Sysname> quit
2. Log in again through the AUX line.
The following message appears:
Press ENTER to get started.
3. Press Enter.
Pressing Enter does not start a session.
4. Enter s.
A terminal session is started.
<Sysname>
Related commands
line
lock
Use lock to lock the current user line. This method prevents unauthorized users from using the user line.
Syntax
lock
Default
By default, the system does not lock any user lines.
Views
User view
Predefined user roles
network-admin
Usage guidelines
This command is not supported in FIPS mode.
After executing the lock command, enter the password for unlocking the user line and confirm the password by entering it again.
To unlock the user line, press Enter and enter the correct password.
Examples
# Lock the current user line and then unlock it.
<Sysname> lock
Please input password<1 to 16> to lock current line:
Password:
Again:
locked !
// The user line is locked. To unlock it, press Enter and enter the password:
Password:
<Sysname>
parity
Use parity to specify a parity check mode.
Use undo parity to restore the default.
Syntax
parity { even | mark | none | odd | space }
undo parity
Default
The setting is none, and no parity check is performed.
Views
User line view
Predefined user roles
network-admin
Parameters
even: Performs even parity check.
mark: Performs mark parity check.
none: Disables parity check.
odd: Performs odd parity check.
space: Performs space parity check.
Usage guidelines
This command is not supported in VTY line view.
The configuration terminal and the device must be configured with the same parity check mode to communicate.
Examples
# Configure user line AUX 0 to perform odd parity check.
<Sysname> system-view
[Sysname] line aux 0
[Sysname-line-aux0] parity odd
protocol inbound
Use protocol inbound to enable a user line to support Telnet, SSH, or both protocols.
Use undo protocol inbound to restore the default.
Syntax
In non-FIPS mode:
protocol inbound { all |ssh | telnet }
undo protocol inbound
In FIPS mode:
protocol inbound ssh
undo protocol inbound
Default
In non-FIPS mode, both protocols are supported.
In FIPS mode, SSH is supported.
Views
VTY line view, VTY line class view
Predefined user roles
network-admin
Parameters
all: Supports both protocols.
ssh: Supports SSH only.
telnet: Supports Telnet only.
Usage guidelines
A protocol change does not take effect for current online users. It takes effect only for new login users.
Before configuring a user line to support SSH, set the authentication mode to scheme for the user line. For more information, see authentication-mode.
This command is available in both VTY line view and VTY line class view. In VTY line view, this command is associated with the authentication-mode command. If you specify a non-default value for only one of the two commands in VTY line view, the other command uses the default setting, regardless of the setting in VTY line class view.
Examples
# Enable user lines VTY 0 through VTY 4 to support only SSH.
<Sysname> system-view
[Sysname] line vty 0 4
[Sysname-line-vty0-4] authentication-mode scheme
[Sysname-line-vty0-4] protocol inbound ssh
# Enable SSH support and set the authentication mode to scheme in VTY line class view. Enable user lines VTY 0 through VTY 4 to support all protocols and disable authentication for the user lines.
[Sysname] line class vty
[Sysname-line-class-vty] authentication-mode scheme
[Sysname-line-class-vty] protocol inbound ssh
[Sysname-line-class-vty] line vty 0 4
[Sysname-line-vty0-4] authentication-mode none
To verify the configuration:
1. Telnet to the device.
<Client> telnet 192.168.1.241
Trying 192.168.1.241 ...
Press CTRL+K to abort
Connected to 192.168.1.241 ...
******************************************************************************
* Copyright (c) 2004-2017 New H3C Technologies Co., Ltd. All rights reserved.*
* Without the owner's prior written consent, *
* no decompiling or reverse-engineering shall be allowed. *
******************************************************************************
<Server>
You are logged in without authentication.
2. Display online CLI user information.
Idx Line Idle Time Pid Type
+ 50 VTY 0 00:00:00 Jan 17 15:29:27 189 TEL
Following are more details.
VTY 0 :
Location: 192.168.1.186
+ : Current operation user.
F : Current operation user works in async mode.
The output shows that you are using VTY 0. The configuration in user line view is effective.
screen-length
Use screen-length to set the maximum number of lines to be displayed on a screen.
Use undo screen-length to restore the default.
Syntax
screen-length screen-length
undo screen-length
Default
Up to 24 lines are displayed on a screen.
Views
User line view, user line class view
Predefined user roles
network-admin
Parameters
screen-length: Specifies the maximum number of lines to be displayed on a screen, in the range of 0 to 512. Setting this argument to 0 disables pausing between screens of output.
Usage guidelines
This command sets the maximum number of lines that can be displayed on one screen when the screen pause feature is enabled. If the screen pause feature is disabled, the system displays command output without a pause.
The actual number of lines that can be displayed on a screen is restricted by the display specification of the configuration terminal. For example, if you set the maximum number of lines for a screen to 40, the device sends 40 lines to the screen at a time. If the display specification is 24 lines, only the last 24 lines are displayed on the screen. To view the previous 16 lines, you must press PgUp.
The screen pause feature is enabled by default. To disable this feature, execute the screen-length 0 command or the screen-length disable command. The screen-length disable command is available in user view.
This command is available in both user line view and user line class view. A non-default setting in either view takes precedence over a default setting in the other view. A non-default setting in user line view takes precedence over a non-default setting in user line class view.
Examples
# Set the maximum number of lines to be displayed on a screen to 30 for user line AUX 0.
<Sysname> system-view
[Sysname] line aux 0
[Sysname-line-aux0] screen-length 30
screen-length disable
send
Use send to send messages to user lines.
Syntax
send { all | number1 | { aux | vty } number2 }
Views
User view
Predefined user roles
network-admin
Parameters
all: Specifies all user lines.
number1: Specifies the absolute number of a user line, in the range of 0 to 192.
aux: Specifies the AUX line.
vty: Specifies the VTY line.
number2: Specifies the relative number of a user line. The value range is 0 to 128 for the AUX line and 0 to 63 for the VTY line.
Usage guidelines
To end a message, press Enter. To cancel a message and return to user view, press Ctrl+C.
Examples
# Before you restart the device, send a notification to VTY 1 to inform the user.
<Sysname> send vty 1
Input message, end with Enter; abort with CTRL+C:
Your attention, please. I will reboot the system in 3 minutes.
Send message? [Y/N]:y
The message should appear on the screen of the user's configuration terminal, as shown in the following example:
[Sysname]
***
***
***Message from vty0 to vty1
***
Your attention, please. I will reboot the system in 3 minutes.
set authentication password
Use set authentication password to set a password for password authentication.
Use undo set authentication password to remove the password.
Syntax
set authentication password { hash | simple } password
undo set authentication password
Default
No password is set for password authentication.
Views
User line view, user line class view
Predefined user roles
network-admin
Parameters
hash: Sets a hashed password.
simple: Sets a plaintext password.
password: Specifies the password string. This argument is case sensitive. If simple is specified, it must be a string of 1 to 16 characters. If hash is specified, it must be a string of 1 to 110 characters.
Usage guidelines
This command is not supported in FIPS mode.
For security purposes, the password is hashed before being saved, whether you specify the hash or simple keyword.
This command is available in both user line view and user line class view. A non-default setting in either view takes precedence over a default setting in the other view. A non-default setting in user line view takes precedence over a non-default setting in user line class view.
Examples
# Set the password for password authentication on user line AUX 0 to hello.
<Sysname> system-view
[Sysname] line aux 0
[Sysname-line-aux0] authentication-mode password
[Sysname-line-aux0] set authentication password simple hello
When you log in again through user line AUX 0, you must enter the password hello to pass authentication.
Related commands
authentication-mode
shell
Use shell to enable the terminal service for a user line.
Use undo shell to disable the terminal service for a user line.
Syntax
shell
undo shell
Default
The terminal service is enabled on all user lines.
Views
User line view, user line class view
Predefined user roles
network-admin
Usage guidelines
The undo shell command is not supported in AUX line view or AUX line class view.
You cannot disable the terminal service on the user line you are using.
When the device operates as a Telnet or SSH server, you cannot configure the undo shell command.
If the undo shell command is configured in user line class view, you cannot configure the shell command in the view of a user line in the class.
Examples
# Disable the terminal service for user line VTY 0 through VTY 4 so no user can log in to the device through the user lines.
<Sysname> system-view
[Sysname] line vty 0 4
[Sysname-line-vty0-4] undo shell
Disable ui-vty0-4 , are you sure? [Y/N]:y
[Sysname-line-vty0-4]
speed
Use speed to set the transmission rate (also called the "baud rate") on a user line.
Use undo speed to restore the default.
Syntax
speed speed-value
undo speed
Default
The transmission rate is 9600 bps on a user line.
Views
User line view
Predefined user roles
network-admin
Parameters
speed-value: Specifies the transmission rate in bps. Supported transmission rates vary by configuration environment. The transmission rates for asynchronous serial interfaces might include:
· 300 bps.
· 600 bps.
· 1200 bps.
· 2400 bps.
· 4800 bps.
· 9600 bps.
· 19200 bps.
· 38400 bps.
· 57600 bps.
· 115200 bps.
Usage guidelines
This command is not supported in VTY line view.
The configuration terminal and the device must be configured with the same transmission rate to communicate.
Examples
# Set the transmission rate to 19200 bps for user line AUX 0.
<Sysname> system-view
[Sysname] line aux 0
[Sysname-line-aux0] speed 19200
stopbits
Use stopbits to specify the number of stop bits for a character.
Use undo stopbits to restore the default.
Syntax
stopbits { 1 | 1.5 | 2 }
undo stopbits
Default
One stop bit is used.
Views
User line view
Predefined user roles
network-admin
Parameters
1: Uses one stop bit.
1.5: Uses one and a half stop bits. The device does not support using one and a half stop bits. If you specify this keyword, two stop bits are used.
2: Uses two stop bits.
Usage guidelines
This command is not supported in VTY line view.
The configuration terminal and the device must be configured to use the same number of stop bits to communicate.
Examples
# Set the number of stop bits to 1 for user line AUX 0.
<Sysname> system-view
[Sysname] line aux 0
[Sysname-line-aux0] stopbits 1
telnet
Use telnet to Telnet to a host in an IPv4 network.
Syntax
telnet remote-host [ service-port ] [ vpn-instance vpn-instance-name ] [ source { interface interface-type interface-number | ip ip-address } ] [ dscp dscp-value ]
Views
User view
Predefined user roles
network-admin
Parameters
remote-host: Specifies the IPv4 address or host name of a remote host. A host name can be a case-insensitive string of 1 to 253 characters. Valid characters for a host name include letters, digits, hyphens (-), underscores (_), and dots (.).
service-port: Specifies the TCP port number for the Telnet service on the remote host. The value range is 0 to 65535 and the default is 23.
vpn-instance vpn-instance-name: Specifies the VPN instance to which the remote host belongs, where vpn-instance-name is a case-sensitive string of 1 to 31 characters. If the remote host belongs to the public network, do not specify this option.
source: Specifies a source IPv4 address or source interface for outgoing Telnet packets.
interface interface-type interface-number: Specifies the source interface. The primary IPv4 address of the interface will be used as the source IPv4 address for outgoing Telnet packets.
ip ip-address: Specifies the source IPv4 address for outgoing Telnet packets.
dscp dscp-value: Specifies the DSCP value for IP to use in outgoing Telnet packets to indicate the packet transmission priority. The value range is 0 to 63. The default is 48.
Usage guidelines
This command is not supported in FIPS mode.
To terminate the current Telnet connection, press Ctrl+K or execute the quit command.
The source address or interface specified by this command is applied only to the current Telnet connection.
Examples
# Telnet to host 1.1.1.2, using 1.1.1.1 as the source IP address for outgoing Telnet packets.
<Sysname> telnet 1.1.1.2 source ip 1.1.1.1
Related commands
telnet client source
telnet client source
Use telnet client source to specify a source IPv4 address or source interface for outgoing Telnet packets when the device acts as a Telnet client.
Use undo telnet client source to remove the configuration.
Syntax
telnet client source { interface interface-type interface-number | ip ip-address }
undo telnet client source
Default
No source IPv4 address or source interface is specified for outgoing Telnet packets. The source IPv4 address is the primary IPv4 address of the outbound interface.
Views
System view
Predefined user roles
network-admin
Parameters
interface interface-type interface-number: Specifies a source interface. The primary IPv4 address of the interface will be used as the source IPv4 address for outgoing Telnet packets.
ip ip-address: Specifies a source IPv4 address.
Usage guidelines
This command is not supported in FIPS mode.
The source IPv4 address or source interface that is specified by this command applies to all Telnet connections. However, if a user specifies a source IPv4 address or source interface when executing the telnet command, the setting specified by the user takes effect.
Examples
# Set the source IPv4 address for outgoing Telnet packets to 1.1.1.1 when the device acts as a Telnet client.
<Sysname> system-view
[Sysname] telnet client source ip 1.1.1.1
Related commands
display telnet client configuration
telnet ipv6
Use telnet ipv6 to Telnet to a host in an IPv6 network.
Syntax
telnet ipv6 remote-host [ -i interface-type interface-number ] [ port-number ] [ vpn-instance vpn-instance-name ] [ dscp dscp-value ]
Views
User view
Predefined user roles
network-admin
Parameters
remote-host: Specifies the IP address or host name of a remote host. A host name can be a case-insensitive string of 1 to 253 characters. Valid characters for a host name include letters, digits, hyphens (-), underscores (_), and dots (.).
-i interface-type interface-number: Specifies the outbound interface for sending Telnet packets. This option is required when the destination address is a link-local address. When the destination address is a global unicast address, you cannot specify this option.
port-number: Specifies the TCP port number for the Telnet service on the remote host. The value range is 0 to 65535 and the default is 23.
vpn-instance vpn-instance-name: Specifies the VPN instance to which the remote host belongs, where vpn-instance-name is a case-sensitive string of 1 to 31 characters. If the remote host belongs to the public network, do not specify this option.
dscp dscp-value: Specifies the DSCP value for IPv6 to use in outgoing Telnet packets to indicate the packet transmission priority. The value range is 0 to 63. The default is 48.
Usage guidelines
This command is not supported in FIPS mode.
To terminate the current Telnet connection, press Ctrl+K or execute the quit command.
Examples
# Telnet to the host at 5000::1.
<Sysname> telnet ipv6 5000::1
telnet server acl
Use telnet server acl to apply an ACL to filter Telnet logins.
Use undo telnet server acl to restore the default.
Syntax
telnet server acl acl-number
undo telnet server acl
Default
No ACL is used to filter Telnet logins.
Views
System view
Predefined user roles
network-admin
Parameters
acl-number: Specifies an ACL by its number. The following are the value ranges:
· Basic ACL—2000 to 2999.
· Advanced ACL—3000 to 3999.
· Ethernet frame header ACL—4000 to 4999.
Usage guidelines
This command is not supported in FIPS mode.
Only one ACL can be used to filter Telnet logins, and only users permitted by the ACL can Telnet to the device.
This command does not take effect on existing Telnet connections.
You can specify an ACL that has not been created yet in this command. The command takes effect after the ACL is created.
For more information about ACL, see ACL and QoS Configuration Guide.
Examples
# Permit only the user at 1.1.1.1 to Telnet to the device.
<Sysname> system-view
[Sysname] acl number 2001
[Sysname-acl-basic-2001] rule permit source 1.1.1.1 0
[Sysname-acl-basic-2001] quit
[Sysname] telnet server acl 2001
telnet server dscp
Use telnet server dscp to set the DSCP value for IPv4 to use for outgoing Telnet packets on a Telnet server.
Use undo telnet server dscp to restore the default.
Syntax
telnet server dscp dscp-value
undo telnet server dscp
Default
IPv4 uses the DSCP value 48 for outgoing Telnet packets on a Telnet server.
Views
System view
Predefined user roles
network-admin
Parameters
dscp-value: Specifies a DSCP value in the range of 0 to 63.
Usage guidelines
This command is not supported in FIPS mode.
The DSCP value is carried in the ToS field of an IP packet, and it indicates the transmission priority of the packet.
Examples
# Set the DSCP value for IPv4 to use for outgoing Telnet packets to 30 on a Telnet server.
<Sysname> system-view
[Sysname] telnet server dscp 30
telnet server enable
Use telnet server enable to enable the Telnet server feature.
Use undo telnet server enable to disable the Telnet server feature.
Syntax
telnet server enable
undo telnet server enable
Default
The Telnet server feature is disabled.
Views
System view
Predefined user roles
network-admin
Usage guidelines
This command is not supported in FIPS mode.
Administrators can Telnet to the device only when the Telnet server feature is enabled.
Examples
# Enable the Telnet server feature.
<Sysname> system-view
[Sysname] telnet server enable
telnet server ipv6 acl
Use telnet server ipv6 acl to apply an IPv6 ACL to filter IPv6 Telnet logins.
Use undo telnet server ipv6 acl to restore the default.
Syntax
telnet server ipv6 acl [ ipv6 ] acl-number
undo telnet server ipv6 acl
Default
No IPv6 ACL is used to filter IPv6 Telnet logins.
Views
System view
Predefined user roles
network-admin
Parameters
acl-number: Specifies an IPv6 ACL by its number. The following are the value ranges:
· Basic ACL—2000 to 2999. The ipv6 keyword is required.
· Advanced ACL—3000 to 3999. The ipv6 keyword is required.
· Ethernet frame header ACL—4000 to 4999. Do not specify the ipv6 keyword.
Usage guidelines
This command is not supported in FIPS mode.
If the ACL does not exist or does not have a rule, all users are permitted to Telnet to the device.
When the ACL exists and has rules, only users permitted by the ACL can Telnet to the device.
This command is not effective for existing Telnet connections.
If you execute this command multiple times, the most recent configuration takes effect.
For more information about ACL, see ACL and QoS Configuration Guide.
Examples
# Permit only the user at 2000::1 to Telnet to the device.
<Sysname> system-view
[Sysname] acl ipv6 number 2001
[Sysname-acl6-basic-2001] rule permit source 2000::1 128
[Sysname-acl6-basic-2001] quit
[Sysname] telnet server ipv6 acl ipv6 2001
telnet server ipv6 dscp
Use telnet server ipv6 dscp to set the DSCP value for IPv6 to use for outgoing Telnet packets on a Telnet server.
Use undo telnet server ipv6 dscp to restore the default.
Syntax
telnet server ipv6 dscp dscp-value
undo telnet server ipv6 dscp
Default
IPv6 uses the DSCP value 48 for outgoing Telnet packets on a Telnet server.
Views
System view
Predefined user roles
network-admin
Parameters
dscp-value: Specifies a DSCP value in the range of 0 to 63.
Usage guidelines
This command is not supported in FIPS mode.
The DSCP value is carried in the Traffic class field of an IPv6 packet, and it indicates the transmission priority of the packet.
Examples
# Set the DSCP value for IPv6 to use for outgoing Telnet packets to 30 on a Telnet server.
<Sysname> system-view
[Sysname] telnet server ipv6 dscp 30
terminal type
Use terminal type to specify the terminal display type.
Use undo terminal type to restore the default.
Syntax
terminal type { ansi | vt100 }
undo terminal type
Default
The terminal display type is ANSI.
Views
User line view, user line class view
Predefined user roles
network-admin
Parameters
ansi: Specifies the terminal display type ANSI.
vt100: Specifies the terminal display type VT100.
Usage guidelines
The device supports two terminal display types: ANSI and VT100. As a best practice, set the display type to VT100 on both the device and the configuration terminal. If either side uses the ANSI type, a display problem such as cursor positioning error might occur when a command line has more than 80 characters.
Examples
# Set the terminal display type to VT100.
<Sysname> system-view
[Sysname] line vty 0
[Sysname-line-vty0] terminal type vt100
user-interface
Use user-interface to enter one or multiple user line views.
Syntax
user-interface { first-number1 [ last-number1 ] | { aux | vty } first-number2 [ last-number2 ] }
Views
System view
Predefined user roles
network-admin
Parameters
first-number1: Specifies the absolute number of the first user line, in the range of 0 to 192.
last-number1: Specifies the absolute number of the last user line. This number cannot be smaller than first-number1.
aux: Specifies the AUX line.
vty: Specifies the VTY line.
first-number2: Specifies the relative number of the first user line. The value range is 0 to 128 for the AUX line and 0 to 63 for the VTY line.
last-number2: Specifies the relative number of the last user line. This number cannot be smaller than first-number2.
Usage guidelines
To configure settings for a single user line, use this command to enter the user line view.
To configure the same settings for multiple user lines, use this command to enter multiple user line views.
This command is an older version reserved for backward compatibility purposes. As a best practice, use the line command.
Examples
# Enter the view of user line AUX 0.
<Sysname> system-view
[Sysname] user-interface aux 0
[Sysname-line-aux0]
# Enter the views of user lines VTY 0 to VTY 4.
<Sysname> system-view
[Sysname] user-interface vty 0 4
[Sysname-line-vty0-4]
user-interface class
user-interface class
Use user-interface class to enter user line class view.
Syntax
user-interface class { aux | vty }
Views
System view
Predefined user roles
network-admin
Parameters
aux: Specifies the AUX line class view.
vty: Specifies the VTY line class view.
Usage guidelines
This command is an older version reserved for backward compatibility purposes. As a best practice, use the line class command.
To configure the same settings for all user lines of a line class, you can use this command to enter the user line class view.
Some login management commands are available in both user line view and user line class view. For these commands, the device uses the following rules to determine the settings to be activated:
· A setting in user line view is applied only to the user line. A setting in user line class view is applied to all user lines of the class.
· A non-default setting in either view takes precedence over a default setting in the other view. A non-default setting in user line view takes precedence over a non-default setting in user line class view.
· A setting in user line view takes effect immediately and affects the online user. A setting in user line class view takes effect only for new login users. It does not affect online users.
Examples
# Set the CLI connection idle-timeout timer to 15 minutes in VTY line class view.
<Sysname> system-view
[Sysname] user-interface class vty
[Sysname-line-class-vty] idle-timeout 15
# In AUX line class view, configure character s as the shortcut key for starting a terminal session.
<Sysname> system-view
[Sysname] user-interface class aux
[Sysname-line-class-aux] activation-key s
[Sysname-line-class-aux] quit
# In AUX line view, restore the default shortcut key for starting a terminal session.
[Sysname] line aux 0
[Sysname-line-aux0] undo activation-key
Alternatively:
[Sysname-line-aux0] activation-key 13
To verify the configuration:
1. Exit the console session.
[Sysname-line-aux0] return
<Sysname> quit
2. Log in again through the AUX line.
The following message appears:
Press ENTER to get started.
3. Press Enter.
Pressing Enter does not start a session.
4. Enter s.
A terminal session is started.
<Sysname>
Related commands
user-interface
user-role
Use user-role to assign a user role to a user line so users logged in through the user line get the user role at login.
Use undo user-role to remove a user role or restore the default.
Syntax
user-role role-name
undo user-role [ role-name ]
Default
An AUX line user is assigned the user role network-admin. Users of other user lines are assigned the user role network-operator.
Views
User line view, user line class view
Predefined user roles
network-admin
Parameters
role-name: Specifies a user role name, a case-sensitive string of 1 to 63 characters. The user role can be user-defined or predefined (network-admin, network-operator, or level-0 to level-15). If you do not specify this argument, the undo user-role command restores the default user role.
Usage guidelines
This command is not supported in FIPS mode.
You can assign up to 64 user roles to a user line. A user logged in through the user line gets all the user roles.
For more information about user roles, see "Configuring RBAC."
Examples
# Assign user role network-admin through the user line VTY 0.
<Sysname> system-view
[Sysname] line vty 0
[Sysname-line-vty0] user-role network-admin
