H3C S6520X-SI Switch Series System Log Messages Reference-6W100

HomeSupportResource CenterSwitchesH3C S6520X Series SwitchesH3C S6520X-SI Series SwitchesTechnical DocumentsMaintainMessage ReferencesH3C S6520X-SI Switch Series System Log Messages Reference-6W100

 

System Log Messages Reference

 

 

 

H3C S6520X-HI Switch Series Release 11xx

H3C S6520X-EI Switch Series Release 11xx

H3C S6520X-SI Switch Series Release 11xx

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Document version: 6W100-20181102

 

Copyright © 2018 New H3C Technologies Co., Ltd. All rights reserved.

No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of New H3C Technologies Co., Ltd.

Except for the trademarks of New H3C Technologies Co., Ltd., any trademarks that may be mentioned in this document are the property of their respective owners.

The information in this document is subject to change without notice.


Contents

Introduction· 1

System log message format 1

Managing and obtaining system log messages· 3

Obtaining log messages from the console terminal 3

Obtaining log messages from the log buffer 3

Obtaining log messages from a monitor terminal 3

Obtaining log messages from the log file· 3

Obtaining log messages from a log host 4

Software module list 4

Using this document 7

AAA messages· 9

AAA_FAILURE· 9

AAA_LAUNCH·· 9

AAA_SUCCESS· 10

ACL messages· 11

ACL_ACCELERATE_NO_RES· 11

ACL_ACCELERATE_NONCONTIGUOUSMASK· 11

ACL_ACCELERATE_NOT_SUPPORT· 11

ACL_ACCELERATE_NOT_SUPPORTHOPBYHOP· 12

ACL_ACCELERATE_NOT_SUPPORTMULTITCPFLAG·· 12

ACL_ACCELERATE_UNK_ERR·· 12

ACL_IPV6_STATIS_INFO·· 13

ACL_NO_MEM·· 13

ACL_STATIS_INFO·· 13

ANCP messages· 14

ANCP_INVALID_PACKET· 14

APMGR messages· 15

APMGR_AC_MEM_ALERT· 15

APMGR_ADD_AP_FAIL· 15

APMGR_ADDBAC_INFO·· 16

APMGR_AP_OFFLINE· 16

APMGR_AP_ONLINE· 16

APMGR_CWC_IMG_DOWNLOAD_COMPLETE· 17

APMGR_CWC_IMG_DOWNLOAD_START· 17

APMGR_CWC_IMG_NO_ENOUGH_SPACE· 17

APMGR_CWC_LOCAL_AC_DOWN·· 18

APMGR_CWC_LOCAL_AC_UP· 18

APMGR_CWC_REBOOT· 19

APMGR_CWC_RUN_DOWNLOAD_COMPLETE· 19

APMGR_CWC_RUN_DOWNLOAD_START· 19

APMGR_CWC_RUN_NO_ENOUGH_SPACE· 20

APMGR_CWC_TUNNEL_DOWN·· 20

APMGR_CWC_TUNNEL_UP· 21

APMGR_CWS_IMG_DOWNLOAD_COMPLETE· 21

APMGR_CWS_IMG_DOWNLOAD_START· 21

APMGR_CWS_LOCAL_AC_DOWN·· 22

APMGR_CWS_LOCAL_AC_UP· 22

APMGR_CWS_RUN_DOWNLOAD_COMPLETE· 23

APMGR_CWS_RUN_DOWNLOAD_START· 23

APMGR_CWS_TUNNEL_DOWN·· 24

APMGR_CWS_TUNNEL_UP· 24

APMGR_DELBAC_INFO·· 25

APMGR_LOCAL_AC_OFFLINE· 25

APMGR_LOCAL_AC_ONLINE· 25

ARP messages· 26

ARP_ACTIVE_ACK_NO_REPLY· 26

ARP_ACTIVE_ACK_NOREQUESTED_REPLY· 26

ARP_BINDRULETOHW_FAILED·· 27

ARP_DETECTION_LOG·· 27

ARP_DUPLICATE_IPADDR_DETECT· 28

ARP_DYNAMIC·· 28

ARP_DYNAMIC_IF· 29

ARP_DYNAMIC_SLOT· 29

ARP_ENTRY_CONFLICT· 30

ARP_HOST_IP_CONFLICT· 30

ARP_LOCALPROXY_ENABLE_FAILED·· 31

ARP_RATE_EXCEEDED·· 31

ARP_RATELIMIT_NOTSUPPORT· 31

ARP_SENDER_IP_INVALID·· 32

ARP_SENDER_MAC_INVALID·· 32

ARP_SENDER_SMACCONFLICT· 33

ARP_SENDER_SMACCONFLICT_VSI 33

ARP_SRC_MAC_FOUND_ATTACK· 34

ARP_SUP_ENABLE_FAILED·· 34

ARP_TARGET_IP_INVALID·· 34

ARP_THRESHOLD_REACHED·· 35

DUPIFIP· 35

DUPIP· 35

DUPVRRPIP· 36

ATK messages· 37

ATK_ICMP_ADDRMASK_REQ·· 37

ATK_ICMP_ADDRMASK_REQ_RAW·· 38

ATK_ICMP_ADDRMASK_REQ_RAW_SZ· 39

ATK_ICMP_ADDRMASK_REQ_SZ· 40

ATK_ICMP_ADDRMASK_RPL· 41

ATK_ICMP_ADDRMASK_RPL_RAW·· 42

ATK_ICMP_ADDRMASK_RPL_RAW_SZ· 43

ATK_ICMP_ADDRMASK_RPL_SZ· 44

ATK_ICMP_ECHO_REQ·· 45

ATK_ICMP_ECHO_REQ_RAW·· 46

ATK_ICMP_ECHO_REQ_RAW_SZ· 47

ATK_ICMP_ECHO_REQ_SZ· 48

ATK_ICMP_ECHO_RPL· 49

ATK_ICMP_ECHO_RPL_RAW·· 50

ATK_ICMP_ECHO_RPL_RAW_SZ· 51

ATK_ICMP_ECHO_RPL_SZ· 52

ATK_ICMP_FLOOD·· 53

ATK_ICMP_FLOOD_SZ· 53

ATK_ICMP_INFO_REQ·· 54

ATK_ICMP_INFO_REQ_RAW·· 55

ATK_ICMP_INFO_REQ_RAW_SZ· 56

ATK_ICMP_INFO_REQ_SZ· 57

ATK_ICMP_INFO_RPL· 58

ATK_ICMP_INFO_RPL_RAW·· 59

ATK_ICMP_INFO_RPL_RAW_SZ· 60

ATK_ICMP_INFO_RPL_SZ· 61

ATK_ICMP_LARGE· 62

ATK_ICMP_LARGE_RAW·· 63

ATK_ICMP_LARGE_RAW_SZ· 63

ATK_ICMP_LARGE_SZ· 64

ATK_ICMP_PARAPROBLEM·· 65

ATK_ICMP_PARAPROBLEM_RAW·· 66

ATK_ICMP_PARAPROBLEM_RAW_SZ· 67

ATK_ICMP_PARAPROBLEM_SZ· 68

ATK_ICMP_PINGOFDEATH·· 69

ATK_ICMP_PINGOFDEATH_RAW·· 70

ATK_ICMP_PINGOFDEATH_RAW_SZ· 70

ATK_ICMP_PINGOFDEATH_SZ· 71

ATK_ICMP_REDIRECT· 72

ATK_ICMP_REDIRECT_RAW·· 73

ATK_ICMP_REDIRECT_RAW_SZ· 74

ATK_ICMP_REDIRECT_SZ· 75

ATK_ICMP_SMURF· 76

ATK_ICMP_SMURF_RAW·· 77

ATK_ICMP_SMURF_RAW_SZ· 78

ATK_ICMP_SMURF_SZ· 79

ATK_ICMP_SOURCEQUENCH·· 80

ATK_ICMP_SOURCEQUENCH_RAW·· 81

ATK_ICMP_SOURCEQUENCH_RAW_SZ· 82

ATK_ICMP_SOURCEQUENCH_SZ· 83

ATK_ICMP_TIMEEXCEED·· 84

ATK_ICMP_TIMEEXCEED_RAW·· 85

ATK_ICMP_TIMEEXCEED_RAW_SZ· 86

ATK_ICMP_TIMEEXCEED_SZ· 87

ATK_ICMP_TRACEROUTE· 88

ATK_ICMP_TRACEROUTE_RAW·· 89

ATK_ICMP_TRACEROUTE_RAW_SZ· 89

ATK_ICMP_TRACEROUTE_SZ· 90

ATK_ICMP_TSTAMP_REQ·· 91

ATK_ICMP_TSTAMP_REQ_RAW·· 92

ATK_ICMP_TSTAMP_REQ_RAW_SZ· 93

ATK_ICMP_TSTAMP_REQ_SZ· 94

ATK_ICMP_TSTAMP_RPL· 95

ATK_ICMP_TSTAMP_RPL_RAW·· 96

ATK_ICMP_TSTAMP_RPL_RAW_SZ· 97

ATK_ICMP_TSTAMP_RPL_SZ· 98

ATK_ICMP_TYPE· 99

ATK_ICMP_TYPE_RAW·· 100

ATK_ICMP_TYPE_RAW_SZ· 101

ATK_ICMP_TYPE_SZ· 102

ATK_ICMP_UNREACHABLE· 103

ATK_ICMP_UNREACHABLE_RAW·· 104

ATK_ICMP_UNREACHABLE_RAW_SZ· 105

ATK_ICMP_UNREACHABLE_SZ· 106

ATK_ICMPV6_DEST_UNREACH·· 107

ATK_ICMPV6_DEST_UNREACH_RAW·· 108

ATK_ICMPV6_DEST_UNREACH_RAW_SZ· 108

ATK_ICMPV6_DEST_UNREACH_SZ· 109

ATK_ICMPV6_ECHO_REQ·· 110

ATK_ICMPV6_ECHO_REQ_RAW·· 111

ATK_ICMPV6_ECHO_REQ_RAW_SZ· 111

ATK_ICMPV6_ECHO_REQ_SZ· 112

ATK_ICMPV6_ECHO_RPL· 113

ATK_ICMPV6_ECHO_RPL_RAW·· 114

ATK_ICMPV6_ECHO_RPL_RAW_SZ· 114

ATK_ICMPV6_ECHO_RPL_SZ· 115

ATK_ICMPV6_FLOOD·· 116

ATK_ICMPV6_FLOOD_SZ· 116

ATK_ICMPV6_GROUPQUERY· 117

ATK_ICMPV6_GROUPQUERY_RAW·· 118

ATK_ICMPV6_GROUPQUERY_RAW_SZ· 118

ATK_ICMPV6_GROUPQUERY_SZ· 119

ATK_ICMPV6_GROUPREDUCTION·· 120

ATK_ICMPV6_GROUPREDUCTION_RAW·· 121

ATK_ICMPV6_GROUPREDUCTION_RAW_SZ· 121

ATK_ICMPV6_GROUPREDUCTION_SZ· 122

ATK_ICMPV6_GROUPREPORT· 123

ATK_ICMPV6_GROUPREPORT_RAW·· 124

ATK_ICMPV6_GROUPREPORT_RAW_SZ· 124

ATK_ICMPV6_GROUPREPORT_SZ· 125

ATK_ICMPV6_LARGE· 126

ATK_ICMPV6_LARGE_RAW·· 126

ATK_ICMPV6_LARGE_RAW_SZ· 127

ATK_ICMPV6_LARGE_SZ· 127

ATK_ICMPV6_PACKETTOOBIG·· 128

ATK_ICMPV6_PACKETTOOBIG_RAW·· 129

ATK_ICMPV6_PACKETTOOBIG_RAW_SZ· 129

ATK_ICMPV6_PACKETTOOBIG_SZ· 130

ATK_ICMPV6_PARAPROBLEM·· 131

ATK_ICMPV6_PARAPROBLEM_RAW·· 132

ATK_ICMPV6_PARAPROBLEM_RAW_SZ· 132

ATK_ICMPV6_PARAPROBLEM_SZ· 133

ATK_ICMPV6_TIMEEXCEED·· 134

ATK_ICMPV6_TIMEEXCEED_RAW·· 135

ATK_ICMPV6_TIMEEXCEED_RAW_SZ· 135

ATK_ICMPV6_TIMEEXCEED_SZ· 136

ATK_ICMPV6_TRACEROUTE· 137

ATK_ICMPV6_TRACEROUTE_RAW·· 138

ATK_ICMPV6_TRACEROUTE_RAW_SZ· 139

ATK_ICMPV6_TRACEROUTE_SZ· 140

ATK_ICMPV6_TYPE· 141

ATK_ICMPV6_TYPE _RAW_SZ· 142

ATK_ICMPV6_TYPE_RAW·· 142

ATK_ICMPV6_TYPE_SZ· 143

ATK_IP_OPTION·· 144

ATK_IP_OPTION_RAW·· 145

ATK_IP_OPTION_RAW_SZ· 146

ATK_IP_OPTION_SZ· 147

ATK_IP4_ACK_FLOOD·· 148

ATK_IP4_ACK_FLOOD_SZ· 148

ATK_IP4_DIS_PORTSCAN·· 149

ATK_IP4_DIS_PORTSCAN_SZ· 149

ATK_IP4_DNS_FLOOD·· 150

ATK_IP4_DNS_FLOOD_SZ· 150

ATK_IP4_FIN_FLOOD·· 151

ATK_IP4_FIN_FLOOD_SZ· 151

ATK_IP4_FRAGMENT· 152

ATK_IP4_FRAGMENT_RAW·· 153

ATK_IP4_FRAGMENT_RAW_SZ· 154

ATK_IP4_FRAGMENT_SZ· 155

ATK_IP4_HTTP_FLOOD·· 156

ATK_IP4_HTTP_FLOOD_SZ· 156

ATK_IP4_IMPOSSIBLE· 157

ATK_IP4_IMPOSSIBLE_RAW·· 158

ATK_IP4_IMPOSSIBLE_RAW_SZ· 159

ATK_IP4_IMPOSSIBLE_SZ· 160

ATK_IP4_IPSWEEP· 161

ATK_IP4_IPSWEEP_SZ· 161

ATK_IP4_PORTSCAN·· 162

ATK_IP4_PORTSCAN_SZ· 162

ATK_IP4_RST_FLOOD·· 163

ATK_IP4_RST_FLOOD_SZ· 163

ATK_IP4_SYN_FLOOD·· 164

ATK_IP4_SYN_FLOOD_SZ· 164

ATK_IP4_SYNACK_FLOOD·· 165

ATK_IP4_SYNACK_FLOOD_SZ· 165

ATK_IP4_TCP_ALLFLAGS· 166

ATK_IP4_TCP_ALLFLAGS_RAW·· 167

ATK_IP4_TCP_ALLFLAGS_RAW_SZ· 167

ATK_IP4_TCP_ALLFLAGS_SZ· 168

ATK_IP4_TCP_FINONLY· 169

ATK_IP4_TCP_FINONLY_RAW·· 170

ATK_IP4_TCP_FINONLY_RAW_SZ· 170

ATK_IP4_TCP_FINONLY_SZ· 171

ATK_IP4_TCP_INVALIDFLAGS· 172

ATK_IP4_TCP_INVALIDFLAGS_RAW·· 173

ATK_IP4_TCP_INVALIDFLAGS_RAW_SZ· 174

ATK_IP4_TCP_INVALIDFLAGS_SZ· 175

ATK_IP4_TCP_LAND·· 176

ATK_IP4_TCP_LAND_RAW·· 177

ATK_IP4_TCP_LAND_RAW_SZ· 177

ATK_IP4_TCP_LAND_SZ· 178

ATK_IP4_TCP_NULLFLAG·· 179

ATK_IP4_TCP_NULLFLAG_RAW·· 180

ATK_IP4_TCP_NULLFLAG_RAW_SZ· 180

ATK_IP4_TCP_NULLFLAG_SZ· 181

ATK_IP4_TCP_SYNFIN·· 182

ATK_IP4_TCP_SYNFIN_RAW·· 183

ATK_IP4_TCP_SYNFIN_RAW_SZ· 183

ATK_IP4_TCP_SYNFIN_SZ· 184

ATK_IP4_TCP_WINNUKE· 185

ATK_IP4_TCP_WINNUKE_RAW·· 186

ATK_IP4_TCP_WINNUKE_RAW_SZ· 186

ATK_IP4_TCP_WINNUKE_SZ· 187

ATK_IP4_TEARDROP· 188

ATK_IP4_TEARDROP_RAW·· 189

ATK_IP4_TEARDROP_RAW_SZ· 190

ATK_IP4_TEARDROP_SZ· 191

ATK_IP4_TINY_FRAGMENT· 192

ATK_IP4_TINY_FRAGMENT_RAW·· 193

ATK_IP4_TINY_FRAGMENT_RAW_SZ· 194

ATK_IP4_TINY_FRAGMENT_SZ· 195

ATK_IP4_UDP_BOMB· 196

ATK_IP4_UDP_BOMB_RAW·· 197

ATK_IP4_UDP_BOMB_RAW_SZ· 198

ATK_IP4_UDP_BOMB_SZ· 199

ATK_IP4_UDP_FLOOD·· 200

ATK_IP4_UDP_FLOOD_SZ· 200

ATK_IP4_UDP_FRAGGLE· 201

ATK_IP4_UDP_FRAGGLE_RAW·· 202

ATK_IP4_UDP_FRAGGLE_RAW_SZ· 202

ATK_IP4_UDP_FRAGGLE_SZ· 203

ATK_IP4_UDP_SNORK· 204

ATK_IP4_UDP_SNORK_RAW·· 205

ATK_IP4_UDP_SNORK_RAW_SZ· 205

ATK_IP4_UDP_SNORK_SZ· 206

ATK_IP6_ACK_FLOOD·· 207

ATK_IP6_ACK_FLOOD_SZ· 207

ATK_IP6_DIS_PORTSCAN·· 208

ATK_IP6_DIS_PORTSCAN_SZ· 208

ATK_IP6_DNS_FLOOD·· 209

ATK_IP6_DNS_FLOOD_SZ· 209

ATK_IP6_FIN_FLOOD·· 210

ATK_IP6_FIN_FLOOD_SZ· 210

ATK_IP6_FRAGMENT· 211

ATK_IP6_FRAGMENT_RAW·· 212

ATK_IP6_FRAGMENT_RAW_SZ· 212

ATK_IP6_FRAGMENT_SZ· 213

ATK_IP6_HTTP_FLOOD·· 214

ATK_IP6_HTTP_FLOOD_SZ· 214

ATK_IP6_IMPOSSIBLE· 215

ATK_IP6_IMPOSSIBLE_RAW·· 216

ATK_IP6_IMPOSSIBLE_RAW_SZ· 216

ATK_IP6_IMPOSSIBLE_SZ· 217

ATK_IP6_IPSWEEP· 217

ATK_IP6_IPSWEEP_SZ· 218

ATK_IP6_PORTSCAN·· 218

ATK_IP6_PORTSCAN_SZ· 219

ATK_IP6_RST_FLOOD·· 219

ATK_IP6_RST_FLOOD_SZ· 220

ATK_IP6_SYN_FLOOD·· 220

ATK_IP6_SYN_FLOOD_SZ· 221

ATK_IP6_SYNACK_FLOOD·· 221

ATK_IP6_SYNACK_FLOOD_SZ· 222

ATK_IP6_TCP_ALLFLAGS· 222

ATK_IP6_TCP_ALLFLAGS_RAW·· 223

ATK_IP6_TCP_ALLFLAGS_RAW_SZ· 223

ATK_IP6_TCP_ALLFLAGS_SZ· 224

ATK_IP6_TCP_FINONLY· 225

ATK_IP6_TCP_FINONLY_RAW·· 225

ATK_IP6_TCP_FINONLY_RAW_SZ· 226

ATK_IP6_TCP_FINONLY_SZ· 226

ATK_IP6_TCP_INVALIDFLAGS· 227

ATK_IP6_TCP_INVALIDFLAGS_RAW·· 228

ATK_IP6_TCP_INVALIDFLAGS_RAW_SZ· 229

ATK_IP6_TCP_INVALIDFLAGS_SZ· 230

ATK_IP6_TCP_LAND·· 231

ATK_IP6_TCP_LAND_RAW·· 231

ATK_IP6_TCP_LAND_RAW_SZ· 232

ATK_IP6_TCP_LAND_SZ· 232

ATK_IP6_TCP_NULLFLAG·· 233

ATK_IP6_TCP_NULLFLAG_RAW·· 233

ATK_IP6_TCP_NULLFLAG_RAW_SZ· 234

ATK_IP6_TCP_NULLFLAG_SZ· 234

ATK_IP6_TCP_SYNFIN·· 235

ATK_IP6_TCP_SYNFIN_RAW·· 235

ATK_IP6_TCP_SYNFIN_RAW_SZ· 236

ATK_IP6_TCP_SYNFIN_SZ· 236

ATK_IP6_TCP_WINNUKE· 237

ATK_IP6_TCP_WINNUKE_RAW·· 237

ATK_IP6_TCP_WINNUKE_RAW_SZ· 238

ATK_IP6_TCP_WINNUKE_SZ· 238

ATK_IP6_UDP_FLOOD·· 239

ATK_IP6_UDP_FLOOD_SZ· 239

ATK_IP6_UDP_FRAGGLE· 240

ATK_IP6_UDP_FRAGGLE_RAW·· 240

ATK_IP6_UDP_FRAGGLE_RAW_SZ· 241

ATK_IP6_UDP_FRAGGLE_SZ· 241

ATK_IP6_UDP_SNORK· 242

ATK_IP6_UDP_SNORK_RAW·· 242

ATK_IP6_UDP_SNORK_RAW_SZ· 243

ATK_IP6_UDP_SNORK_SZ· 243

ATK_IPOPT_ABNORMAL· 244

ATK_IPOPT_ABNORMAL_RAW·· 245

ATK_IPOPT_ABNORMAL_RAW_SZ· 246

ATK_IPOPT_ABNORMAL_SZ· 247

ATK_IPOPT_LOOSESRCROUTE· 248

ATK_IPOPT_LOOSESRCROUTE_RAW·· 249

ATK_IPOPT_LOOSESRCROUTE_RAW_SZ· 250

ATK_IPOPT_LOOSESRCROUTE_SZ· 251

ATK_IPOPT_RECORDROUTE· 252

ATK_IPOPT_RECORDROUTE_RAW·· 253

ATK_IPOPT_RECORDROUTE_RAW_SZ· 254

ATK_IPOPT_RECORDROUTE_SZ· 255

ATK_IPOPT_ROUTEALERT· 256

ATK_IPOPT_ROUTEALERT_RAW·· 257

ATK_IPOPT_ROUTEALERT_RAW_SZ· 258

ATK_IPOPT_ROUTEALERT_SZ· 259

ATK_IPOPT_SECURITY· 260

ATK_IPOPT_SECURITY_RAW·· 261

ATK_IPOPT_SECURITY_RAW_SZ· 262

ATK_IPOPT_SECURITY_SZ· 263

ATK_IPOPT_STREAMID·· 264

ATK_IPOPT_STREAMID_RAW·· 265

ATK_IPOPT_STREAMID_RAW_SZ· 266

ATK_IPOPT_STREAMID_SZ· 267

ATK_IPOPT_STRICTSRCROUTE· 268

ATK_IPOPT_STRICTSRCROUTE_RAW·· 269

ATK_IPOPT_STRICTSRCROUTE_RAW_SZ· 270

ATK_IPOPT_STRICTSRCROUTE_SZ· 271

ATK_IPOPT_TIMESTAMP· 272

ATK_IPOPT_TIMESTAMP_RAW·· 273

ATK_IPOPT_TIMESTAMP_RAW_SZ· 274

ATK_IPOPT_TIMESTAMP_SZ· 275

ATK_IPV6_EXT_HEADER·· 276

ATK_IPV6_EXT_HEADER_RAW·· 277

ATK_IPV6_EXT_HEADER_RAW_SZ· 277

ATK_IPV6_EXT_HEADER_SZ· 278

ATM·· 279

ATM_PVCDOWN·· 279

ATM_PVCUP· 280

BFD messages· 281

BFD_CHANGE_FSM·· 281

BFD_REACHED_UPPER_LIMIT· 281

BGP messages· 282

BGP_EXCEED_ROUTE_LIMIT· 282

BGP_REACHED_THRESHOLD·· 282

BGP_LOG_ROUTE_FLAP· 283

BGP_MEM_ALERT· 283

BGP_PEER_LICENSE_REACHED·· 283

BGP_ROUTE_LICENSE_REACHED·· 284

BGP_STATE_CHANGED·· 284

BLS messages· 285

BLS_ENTRY_ADD·· 285

BLS_ENTRY_DEL· 285

BLS_IPV6_ENTRY_ADD·· 286

BLS_IPV6_ENTRY_DEL· 286

CFD messages· 287

CFD_CROSS_CCM·· 287

CFD_ERROR_CCM·· 287

CFD_LOST_CCM·· 288

CFD_RECEIVE_CCM·· 288

CFGMAN messages· 289

CFGMAN_ARCHIVE_SCP_FAIL· 289

CFGMAN_CFGCHANGED·· 290

CFGMAN_EXIT_FROM_CONFIGURE· 291

CFGMAN_OPTCOMPLETION·· 291

CONNLMT messages· 293

CONNLMT_IPV4_OVERLOAD·· 293

CONNLMT_IPV4_RECOVER·· 294

CONNLMT_IPV6_OVERLOAD·· 295

CONNLMT_IPV6_RECOVER·· 296

DEV messages· 297

BOARD_INSERTED·· 297

BOARD_REBOOT· 297

BOARD_REMOVED·· 298

BOARD_STATE_FAULT· 298

BOARD_STATE_NORMAL· 298

BOARD_STATE_STARTING·· 299

CFCARD_INSERTED·· 299

CFCARD_REMOVED·· 299

CHASSIS_REBOOT· 300

DEV_CLOCK_CHANGE· 300

DEV_FAULT_TOOLONG·· 300

DYINGGASP· 301

FAN_ABSENT· 301

FAN_DIRECTION_NOT_PREFERRED·· 301

FAN_FAILED·· 302

FAN_RECOVERED·· 302

MAD_DETECT· 302

POWER_ABSENT· 303

POWER_FAILED·· 303

POWER_MONITOR_ABSENT· 303

POWER_MONITOR_FAILED·· 304

POWER_MONITOR_RECOVERED·· 304

POWER_RECOVERED·· 304

RPS_ABSENT· 305

RPS_NORMAL· 305

SUBCARD_FAULT· 305

SUBCARD_INSERTED·· 306

SUBCARD_REBOOT· 306

SUBCARD_REMOVED·· 306

SYSTEM_REBOOT· 307

TEMPERATURE_ALARM·· 307

TEMPERATURE_LOW·· 308

TEMPERATURE_NORMAL· 308

TEMPERATURE_SHUTDOWN·· 309

TEMPERATURE_WARNING·· 309

VCHK_VERSION_INCOMPATIBLE· 310

DHCP· 311

DHCP_NOTSUPPORTED·· 311

DHCP_NORESOURCES· 311

DHCPR· 312

DHCPR_SERVERCHANGE· 312

DHCPR_SWITCHMASTER·· 312

DHCPS messages· 313

DHCPS_ALLOCATE_IP· 313

DHCPS_CONFLICT_IP· 313

DHCPS_EXTEND_IP· 314

DHCPS_FILE· 314

DHCPS_RECLAIM_IP· 315

DHCPS_VERIFY_CLASS· 315

DHCPS6 messages· 316

DHCPS6_ALLOCATE_ADDRESS· 316

DHCPS6_ALLOCATE_PREFIX· 316

DHCPS6_CONFLICT_ADDRESS· 317

DHCPS6_EXTEND_ADDRESS· 317

DHCPS6_EXTEND_PREFIX· 318

DHCPS6_FILE· 318

DHCPS6_RECLAIM_ADDRESS· 319

DHCPS6_RECLAIM_PREFIX· 319

DHCPSP4· 320

DHCPSP4_FILE· 320

DHCPSP6· 321

DHCPSP6_FILE· 321

DIAG messages· 322

CPU_MINOR_RECOVERY· 322

CPU_MINOR_THRESHOLD·· 322

CPU_SEVERE_RECOVERY· 322

CPU_SEVERE_THRESHOLD·· 323

MEM_ALERT· 323

MEM_BELOW_THRESHOLD·· 324

MEM_EXCEED_THRESHOLD·· 325

DLDP messages· 326

DLDP_AUTHENTICATION_FAILED·· 326

DLDP_LINK_BIDIRECTIONAL· 326

DLDP_LINK_SHUTMODECHG·· 327

DLDP_LINK_UNIDIRECTIONAL· 327

DLDP_NEIGHBOR_AGED·· 328

DLDP_NEIGHBOR_CONFIRMED·· 328

DLDP_NEIGHBOR_DELETED·· 329

DOT1X messages· 330

DOT1X_CONFIG_NOTSUPPORT· 330

DOT1X_LOGIN_FAILURE· 330

DOT1X_LOGIN_SUCC·· 331

DOT1X_LOGIN_SUCC (in open mode) 331

DOT1X_LOGOFF· 332

DOT1X_LOGOFF (in open mode) 332

DOT1X_LOGOFF_ABNORMAL· 333

DOT1X_LOGOFF_ABNORMAL (in open mode) 333

DOT1X_MACBINDING_EXIST· 334

DOT1X_NOTENOUGH_EADFREEIP_RES· 334

DOT1X_NOTENOUGH_EADFREERULE_RES· 335

DOT1X_NOTENOUGH_EADMACREDIR_RES· 335

DOT1X_NOTENOUGH_EADPORTREDIR_RES· 335

DOT1X_NOTENOUGH_ENABLEDOT1X_RES· 336

DOT1X_PEXAGG_NOMEMBER_RES· 336

DOT1X_SMARTON_FAILURE· 336

DOT1X_UNICAST_NOT_EFFECTIVE· 337

DRNI 338

DRNI_IFEVENT_DR_BIND·· 338

DRNI_IFEVENT_DR_GLOBALDOWN·· 338

DRNI_IFEVENT_DR_GLOBALUP· 338

DRNI_IFEVENT_DR_NOSELECTED·· 339

DRNI_IFEVENT_DR_PEER_NOSELECTED·· 339

DRNI_IFEVENT_DR_PEER_SELECTED·· 339

DRNI_IFEVENT_DR_SELECTED·· 340

DRNI_IFEVENT_DR_UNBIND·· 340

DRNI_IFEVENT_IPP_BIND·· 340

DRNI_IFEVENT_IPP_DOWN·· 341

DRNI_IFEVENT_IPP_UNBIND·· 341

DRNI_IFEVENT_IPP_UP· 341

DRNI_IPP_BLOCK· 342

DRNI_IPP_UNBLOCK· 342

DRNI_KEEPALIVEINTERVAL_MISMATCH·· 342

DRNI_KEEPALIVELINK_DOWN·· 343

DRNI_KEEPALIVELINK_UP· 343

DRNI_SECONDARY_MADDOWN·· 343

DRNI_SYSEVENT_DEVICEROLE_CHANGE· 344

DRNI_SYSEVENT_MAC_CHANGE· 344

DRNI_SYSEVENT_NUMBER_CHANGE· 344

DRNI_SYSEVENT_PRIORITY_CHANGE· 345

EDEV messages· 346

EDEV_ALARM_IN_REMOVED·· 346

EDEV_ALARM_IN_REPORTEDOCCURRED·· 346

EDEV_BOOTROM_UPDATE_FAILED·· 346

EDEV_BOOTROM_UPDATE_SUCCESS· 347

EDEV_FAILOVER_GROUP_STATE_CHANGE· 347

ERPS messages· 348

ERPS_STATE_CHANGED·· 348

ETHOAM messages· 349

ETHOAM_CONNECTION_FAIL_DOWN·· 349

ETHOAM_CONNECTION_FAIL_TIMEOUT· 349

ETHOAM_CONNECTION_FAIL_UNSATISF· 350

ETHOAM_CONNECTION_SUCCEED·· 350

ETHOAM_DISABLE· 350

ETHOAM_DISCOVERY_EXIT· 351

ETHOAM_ENABLE· 351

ETHOAM_ENTER_LOOPBACK_CTRLLED·· 351

ETHOAM_ENTER_LOOPBACK_CTRLLING·· 352

ETHOAM_LOCAL_DYING_GASP· 352

ETHOAM_LOCAL_ERROR_FRAME· 352

ETHOAM_LOCAL_ERROR_FRAME_PERIOD·· 353

ETHOAM_LOCAL_ERROR_FRAME_SECOND·· 353

ETHOAM_LOCAL_ERROR_SYMBOL· 353

ETHOAM_LOCAL_LINK_FAULT· 354

ETHOAM_LOOPBACK_EXIT· 354

ETHOAM_LOOPBACK_EXIT_ERROR_STATU·· 354

ETHOAM_LOOPBACK_NO_RESOURCE· 355

ETHOAM_LOOPBACK_NOT_SUPPORT· 355

ETHOAM_QUIT_LOOPBACK_CTRLLED·· 355

ETHOAM_QUIT_LOOPBACK_CTRLLING·· 356

ETHOAM_REMOTE_CRITICAL· 356

ETHOAM_REMOTE_DYING_GASP· 356

ETHOAM_REMOTE_ERROR_FRAME· 357

ETHOAM_REMOTE_ERROR_FRAME_PERIOD·· 357

ETHOAM_REMOTE_ERROR_FRAME_SECOND·· 357

ETHOAM_REMOTE_ERROR_SYMBOL· 358

ETHOAM_REMOTE_EXIT· 358

ETHOAM_REMOTE_FAILURE_RECOVER·· 358

ETHOAM_REMOTE_LINK_FAULT· 359

ETHOAM_NO_ENOUGH_RESOURCE· 359

ETHOAM_NOT_CONNECTION_TIMEOUT· 359

EVB messages· 360

EVB_AGG_FAILED·· 360

EVB_LICENSE_EXPIRE· 360

EVB_VSI_OFFLINE· 361

EVB_VSI_ONLINE· 361

EVIISIS messages· 362

EVIISIS_LICENSE_EXPIRED·· 362

EVIISIS_LICENSE_EXPIRED_TIME· 362

EVIISIS_LICENSE_UNAVAILABLE· 362

EVIISIS_NBR_CHG·· 363

FCLINK messages· 364

FCLINK_FDISC_REJECT_NORESOURCE· 364

FCLINK_FLOGI_REJECT_NORESOURCE· 364

FCOE messages· 365

FCOE_INTERFACE_NOTSUPPORT_FCOE· 365

FCOE_LAGG_BIND_ACTIVE· 365

FCOE_LAGG_BIND_DEACTIVE· 366

FCZONE messages· 367

FCZONE_DISTRIBUTE_FAILED·· 367

FCZONE_HARDZONE_DISABLED·· 367

FCZONE_HARDZONE_ENABLED·· 368

FCZONE_ISOLATE_ALLNEIGHBOR·· 368

FCZONE_ISOLATE_CLEAR_VSAN·· 369

FCZONE_ISOLATE_CLEAR_ALLVSAN·· 369

FCZONE_ISOLATE_NEIGHBOR·· 369

FIB messages· 370

FIB_FILE· 370

FILTER messages· 371

FILTER_EXECUTION_ICMP· 371

FILTER_EXECUTION_ICMPV6· 372

FILTER_IPV4_EXECUTION·· 373

FILTER_IPV6_EXECUTION·· 374

FIPS messages· 375

FCOE_FIPS_HARD_RESOURCE_NOENOUGH·· 375

FCOE_FIPS_HARD_RESOURCE_RESTORE· 375

FS messages· 376

FS_UNFORMATTED_PARTITION·· 376

FTPD messages· 377

FTP_ACL_DENY· 377

FTPD_REACH_SESSION_LIMIT· 377

FTPD_AUTHOR_FAILED·· 378

HA messages· 379

HA_BATCHBACKUP_FINISHED·· 379

HA_BATCHBACKUP_STARTED·· 379

HA_STANDBY_NOT_READY· 379

HA_STANDBY_TO_MASTER·· 380

HQOS messages· 381

HQOS_DP_SET_FAIL· 381

HQOS_FP_SET_FAIL· 381

HQOS_POLICY_APPLY_FAIL· 382

HQOS_POLICY_APPLY_FAIL· 382

HTTPD messages· 383

HTTPD_CONNECT· 383

HTTPD_CONNECT_TIMEOUT· 383

HTTPD_DISCONNECT· 384

HTTPD_FAIL_FOR_ACL· 384

HTTPD_FAIL_FOR_ACP· 384

HTTPD_REACH_CONNECT_LIMIT· 385

IFNET messages· 386

IF_BUFFER_CONGESTION_OCCURRENCE· 386

IF_BUFFER_CONGESTION_CLEAR·· 386

IF_JUMBOFRAME_WARN·· 387

INTERFACE_NOTSUPPRESSED·· 387

INTERFACE_SUPPRESSED·· 387

LINK_UPDOWN·· 388

PHY_UPDOWN·· 388

PROTOCOL_UPDOWN·· 388

TUNNEL_LINK_UPDOWN·· 389

TUNNEL_PHY_UPDOWN·· 389

VLAN_MODE_CHANGE· 389

IKE messages· 390

IKE_P1_SA_ESTABLISH_FAIL· 390

IKE_P2_SA_ESTABLISH_FAIL· 390

IKE_P2_SA_TERMINATE· 391

IKE_VERIFY_CERT_FAIL· 392

IPFW·· 394

IPFW_FAILURE· 394

IPSEC messages· 395

IPSEC_FAILED_ADD_FLOW_TABLE· 395

IPSEC_PACKET_DISCARDED·· 395

IPSEC_SA_ESTABLISH·· 396

IPSEC_SA_ESTABLISH_FAIL· 396

IPSEC_SA_INITINATION·· 397

IPSEC_SA_TERMINATE· 397

IPSG messages· 398

IPSG_ADDENTRY_ERROR·· 398

IPSG_DELENTRY_ERROR·· 399

IPSG_ADDEXCLUDEDVLAN_ERROR·· 399

IPSG_DELEXCLUDEDVLAN_ERROR·· 400

IRDP messages· 401

IRDP_EXCEED_ADVADDR_LIMIT· 401

IRF· 402

IRF_LINK_BLOCK· 402

IRF_LINK_DOWN·· 402

IRF_LINK_UP· 402

IRF_MEMBERID_CONFLICT· 403

IRF_MERGE· 403

IRF_MERGE_NEED_REBOOT· 403

IRF_MERGE_NOT_NEED_REBOOT· 404

ISIS messages· 405

ISIS_LSP_CONFLICT· 405

ISIS_MEM_ALERT· 405

ISIS_NBR_CHG·· 406

ISSU messages· 407

ISSU_LOAD_FAILED·· 407

ISSU_LOAD_SUCCESS· 407

ISSU_PROCESSWITCHOVER·· 407

ISSU_ROLLBACKCHECKNORMAL· 408

L2PT messages· 409

L2PT_SET_MULTIMAC_FAILED·· 409

L2PT_CREATE_TUNNELGROUP_FAILED·· 409

L2PT_ADD_GROUPMEMBER_FAILED·· 409

L2PT_ENABLE_DROP_FAILED·· 410

L2TP messages· 411

L2TPV2_TUNNEL_EXCEED_LIMIT· 411

L2TPV2_SESSION_EXCEED_LIMIT· 411

L2VPN messages· 412

L2VPN_BGPVC_CONFLICT_LOCAL· 412

L2VPN_BGPVC_CONFLICT_REMOTE· 412

L2VPN_HARD_RESOURCE_NOENOUGH·· 413

L2VPN_HARD_RESOURCE_RESTORE· 413

L2VPN_LABEL_DUPLICATE· 413

LAGG messages· 414

LAGG_ACTIVE· 414

LAGG_AUTO_AGGREGATION·· 414

LAGG_INACTIVE_AICFG·· 415

LAGG_INACTIVE_BFD·· 415

LAGG_INACTIVE_CONFIGURATION·· 416

LAGG_INACTIVE_DUPLEX· 416

LAGG_INACTIVE_HARDWAREVALUE· 417

LAGG_INACTIVE_LOWER_LIMIT· 417

LAGG_INACTIVE_PARTNER·· 418

LAGG_INACTIVE_PHYSTATE· 418

LAGG_INACTIVE_RESOURCE_INSUFICIE· 419

LAGG_INACTIVE_SPEED·· 419

LAGG_INACTIVE_UPPER_LIMIT· 420

LDP messages· 421

LDP_MPLSLSRID_CHG·· 421

LDP_SESSION_CHG·· 422

LDP_SESSION_GR·· 423

LDP_SESSION_SP· 423

LLDP messages· 424

LLDP_CREATE_NEIGHBOR·· 424

LLDP_DELETE_NEIGHBOR·· 424

LLDP_LESS_THAN_NEIGHBOR_LIMIT· 425

LLDP_NEIGHBOR_AGE_OUT· 425

LLDP_NEIGHBOR_PROTECTION_BLOCK· 426

LLDP_NEIGHBOR_PROTECTION_DOWN·· 426

LLDP_NEIGHBOR_PROTECTION_UNBLOCK· 427

LLDP_NEIGHBOR_PROTECTION_UP· 427

LLDP_PVID_INCONSISTENT· 428

LLDP_REACH_NEIGHBOR_LIMIT· 428

LOAD messages· 429

BOARD_LOADING·· 429

LOAD_FAILED·· 429

LOAD_FINISHED·· 429

LOGIN messages· 430

LOGIN_FAILED·· 430

LOGIN_ INVALID_USERNAME_PWD·· 430

LPDT messages· 431

LPDT_LOOPED·· 431

LPDT_RECOVERED·· 431

LPDT_VLAN_LOOPED·· 431

LPDT_VLAN_RECOVERED·· 432

LS messages· 433

LS_ADD_USER_TO_GROUP· 433

LS_AUTHEN_FAILURE· 433

LS_AUTHEN_SUCCESS· 434

LS_DEL_USER_FROM_GROUP· 434

LS_DELETE_PASSWORD_FAIL· 434

LS_PWD_ADDBLACKLIST· 435

LS_PWD_CHGPWD_FOR_AGEDOUT· 435

LS_PWD_CHGPWD_FOR_AGEOUT· 435

LS_PWD_CHGPWD_FOR_COMPOSITION·· 436

LS_PWD_CHGPWD_FOR_FIRSTLOGIN·· 436

LS_PWD_CHGPWD_FOR_LENGTH·· 436

LS_PWD_FAILED2WRITEPASS2FILE· 437

LS_PWD_MODIFY_FAIL· 437

LS_PWD_MODIFY_SUCCESS· 437

LS_REAUTHEN_FAILURE· 438

LS_UPDATE_PASSWORD_FAIL· 438

LS_USER_CANCEL· 438

LS_USER_PASSWORD_EXPIRE· 439

LS_USER_ROLE_CHANGE· 439

LSPV messages· 440

LSPV_PING_STATIS_INFO·· 440

MAC messages· 441

MAC_DRIVER_ADD_ENTRY· 441

MAC_TABLE_FULL_GLOBAL· 441

MAC_TABLE_FULL_PORT· 442

MAC_TABLE_FULL_VLAN·· 442

MAC_VLAN_LEARNLIMIT_NORESOURCE· 442

MAC_VLAN_LEARNLIMIT_NOTSUPPORT· 443

MACA messages· 444

MACA_ENABLE_NOT_EFFECTIVE· 444

MACA_LOGIN_FAILURE· 444

MACA_LOGIN_SUCC·· 445

MACA_LOGIN_SUCC (in open mode) 445

MACA_LOGOFF· 446

MACA_LOGOFF (in open mode) 446

MACSEC messages· 447

MACSEC_MKA_KEEPALIVE_TIMEOUT· 447

MACSEC_MKA_PRINCIPAL_ACTOR·· 447

MACSEC_MKA_SAK_REFRESH·· 448

MACSEC_MKA_SESSION_REAUTH·· 448

MACSEC_MKA_SESSION_SECURED·· 449

MACSEC_MKA_SESSION_START· 449

MACSEC_MKA_SESSION_STOP· 450

MACSEC_MKA_SESSION_UNSECURED·· 450

MBFD messages· 451

MBFD_TRACEROUTE_FAILURE· 451

MBUF messages· 452

MBUF_DATA_BLOCK_CREATE_FAIL· 452

MDC messages· 453

MDC_CREATE_ERR·· 453

MDC_CREATE· 453

MDC_DELETE· 454

MDC_KERNEL_EVENT_TOOLONG·· 454

MDC_LICENSE_EXPIRE· 454

MDC_NO_FORMAL_LICENSE· 455

MDC_NO_LICENSE_EXIT· 455

MDC_OFFLINE· 455

MDC_ONLINE· 456

MDC_STATE_CHANGE· 456

MFIB messages· 457

MFIB_MEM_ALERT· 457

MGROUP messages· 458

MGROUP_APPLY_SAMPLER_FAIL· 458

MGROUP_RESTORE_CPUCFG_FAIL· 458

MGROUP_RESTORE_IFCFG_FAIL· 459

MGROUP_SYNC_CFG_FAIL· 459

MPLS messages· 460

MPLS_HARD_RESOURCE_NOENOUGH·· 460

MPLS_HARD_RESOURCE_RESTORE· 460

MTLK messages· 461

MTLK_UPLINK_STATUS_CHANGE· 461

NAT messages· 462

NAT_ADDR_BIND_CONFLICT· 462

NAT_FAILED_ADD_FLOW_RULE· 462

NAT_FAILED_ADD_FLOW_TABLE· 463

NAT_FLOW·· 463

NAT_SERVICE_CARD_RECOVER_FAILURE· 464

NAT_SERVER_INVALID·· 465

ND messages· 466

ND_CONFLICT· 466

ND_DUPADDR·· 466

ND_HOST_IP_CONFLICT· 467

ND_MAC_CHECK· 467

ND_RAGUARD_DROP· 468

ND_SET_PORT_TRUST_NORESOURCE· 468

ND_SET_VLAN_REDIRECT_NORESOURCE· 468

NETCONF messages· 469

CLI 469

row-operation· 470

THREAD·· 470

NQA messages· 471

NQA_LOG_UNREACHABLE· 471

NTP messages· 472

NTP_CLOCK_CHANGE· 472

NTP_LEAP_CHANGE· 472

NTP_SOURCE_CHANGE· 473

NTP_SOURCE_LOST· 473

NTP_STRATUM_CHANGE· 473

OBJP messages· 474

OBJP_ACCELERATE_NO_RES· 474

OBJP_ACCELERATE_NOT_SUPPORT· 474

OBJP_ACCELERATE_UNK_ERR·· 475

OFP messages· 476

OFP_ACTIVE· 476

OFP_ACTIVE_FAILED·· 476

OFP_CONNECT· 476

OFP_FAIL_OPEN·· 477

OFP_FLOW_ADD·· 477

OFP_FLOW_ADD_ARP_FAILED·· 478

OFP_FLOW_ADD_DUP· 478

OFP_FLOW_ADD_FAILED·· 479

OFP_FLOW_ADD_FAILED·· 479

OFP_FLOW_ADD_TABLE_MISS· 480

OFP_FLOW_ADD_TABLE_MISS_FAILED·· 480

OFP_FLOW_DEL· 481

OFP_FLOW_DEL_L2VPN_DISABLE· 481

OFP_FLOW_DEL_TABLE_MISS· 482

OFP_FLOW_DEL_TABLE_MISS_FAILED·· 482

OFP_FLOW_DEL_VXLAN_DEL· 483

OFP_FLOW_MOD·· 483

OFP_FLOW_MOD_FAILED·· 484

OFP_FLOW_MOD_TABLE_MISS· 484

OFP_FLOW_MOD_TABLE_MISS_FAILED·· 485

OFP_FLOW_RMV_GROUP· 485

OFP_FLOW_RMV_HARDTIME· 485

OFP_FLOW_RMV_IDLETIME· 486

OFP_FLOW_RMV_METER·· 486

OFP_FLOW_UPDATE_FAILED·· 487

OFP_GROUP_ADD·· 487

OFP_GROUP_ADD_FAILED·· 488

OFP_GROUP_DEL· 488

OFP_GROUP_MOD·· 489

OFP_GROUP_MOD_FAILED·· 489

OFP_METER_ADD·· 490

OFP_METER_ADD_FAILED·· 490

OFP_METER_DEL· 491

OFP_METER_MOD·· 491

OFP_METER_MOD_FAILED·· 492

OFP_MISS_RMV_GROUP· 492

OFP_MISS_RMV_HARDTIME· 492

OFP_MISS_RMV_IDLETIME· 493

OFP_MISS_RMV_METER·· 493

OFP_RADARDETECTION·· 493

PORT_MOD·· 494

OPENSRC (FreeRADIUS) messages· 495

HUP event 495

Process restart event 496

Process start event 496

User authentication· 497

OPTMOD messages· 500

BIAS_HIGH·· 500

BIAS_LOW·· 500

BIAS_NORMAL· 501

CFG_ERR·· 501

CHKSUM_ERR·· 501

FIBER_SFP MODULE_INVALID·· 502

FIBER_SFPMODULE_NOWINVALID·· 502

IO_ERR·· 503

MOD_ALM_OFF· 503

MOD_ALM_ON·· 503

MODULE_IN·· 504

MODULE_OUT· 504

PHONY_MODULE· 504

RX_ALM_OFF· 505

RX_ALM_ON·· 505

RX_POW_HIGH·· 505

RX_POW_LOW·· 506

RX_POW_NORMAL· 506

TEMP_HIGH·· 506

TEMP_LOW·· 507

TEMP_NORMAL· 507

TX_ALM_OFF· 507

TX_ALM_ON·· 508

TX_POW_HIGH·· 508

TX_POW_LOW·· 508

TX_POW_NORMAL· 509

TYPE_ERR·· 509

VOLT_HIGH·· 509

VOLT_LOW·· 510

VOLT_NORMAL· 510

OSPF messages· 511

OSPF_DUP_RTRID_NBR·· 511

OSPF_IP_CONFLICT_INTRA· 511

OSPF_LAST_NBR_DOWN·· 512

OSPF_MEM_ALERT· 512

OSPF_NBR_CHG·· 513

OSPF_RT_LMT· 513

OSPF_RTRID_CHG·· 513

OSPF_RTRID_CONFLICT_INTER·· 514

OSPF_RTRID_CONFLICT_INTRA· 514

OSPF_VLINKID_CHG·· 514

OSPFV3 messages· 515

OSPFV3_LAST_NBR_DOWN·· 515

OSPFV3_MEM_ALERT· 515

OSPFV3_NBR_CHG·· 516

OSPFV3_RT_LMT· 516

PBB messages· 517

PBB_JOINAGG_WARNING·· 517

PBR messages· 518

PBR_HARDWARE_ERROR·· 518

PCE messages· 519

PCE_PCEP_SESSION_CHG·· 519

PEX messages (IRF 3) 520

PEX_ASSOCIATEID_MISMATCHING·· 520

PEX_CONFIG_ERROR·· 520

PEX_CONNECTION_ERROR·· 521

PEX_FORBID_STACK· 521

PEX_LINK_BLOCK· 522

PEX_LINK_DOWN·· 523

PEX_LINK_FORWARD·· 523

PEX_REG_JOININ·· 524

PEX_REG_LEAVE· 524

PEX_REG_REQUEST· 525

PEX_STACKCONNECTION_ERROR·· 525

PEX messages (IRF 3.1) 526

PEX_AUTOCONFIG_BAGG_ASSIGNMEMBER·· 526

PEX_AUTOCONFIG_BAGG_CREATE· 526

PEX_AUTOCONFIG_BAGG_NORESOURCE· 527

PEX_AUTOCONFIG_BAGG_REMOVEMEMBER·· 527

PEX_AUTOCONFIG_CAPABILITY_ENABLE· 528

PEX_AUTOCONFIG_CASCADELIMIT· 528

PEX_AUTOCONFIG_CONNECTION_ERROR·· 529

PEX_AUTOCONFIG_DIFFGROUPNUMBER·· 529

PEX_AUTOCONFIG_DYNAMICBAGG_STP· 530

PEX_AUTOCONFIG_GROUP_CREATE· 530

PEX_AUTOCONFIG_NONUMBERRESOURCE· 530

PEX_AUTOCONFIG_NOT_CASCADEPORT· 531

PEX_AUTOCONFIG_NUMBER_ASSIGN·· 531

PEX_LLDP_DISCOVER·· 532

PEX_MEMBERID_EXCEED·· 532

PEX_PECSP_OPEN_RCVD·· 532

PEX_PECSP_OPEN_SEND·· 533

PEX_PECSP_TIMEOUT· 533

PFILTER messages· 534

PFILTER_GLB_IPV4_DACT_NO_RES· 534

PFILTER_GLB_IPV4_DACT_UNK_ERR·· 534

PFILTER_GLB_IPV6_DACT_NO_RES· 535

PFILTER_GLB_IPV6_DACT_UNK_ERR·· 535

PFILTER_GLB_MAC_DACT_NO_RES· 536

PFILTER_GLB_MAC_DACT_UNK_ERR·· 536

PFILTER_GLB_NO_RES· 537

PFILTER_GLB_NOT_SUPPORT· 537

PFILTER_GLB_ RES_CONFLICT· 538

PFILTER_GLB_UNK_ERR·· 538

PFILTER_IF_IPV4_DACT_NO_RES· 539

PFILTER_IF_IPV4_DACT_UNK_ERR·· 539

PFILTER_IF_IPV6_DACT_NO_RES· 540

PFILTER_IF_IPV6_DACT_UNK_ERR·· 540

PFILTER_IF_MAC_DACT_NO_RES· 541

PFILTER_IF_MAC_DACT_UNK_ERR·· 541

PFILTER_IF_NO_RES· 542

PFILTER_IF_NOT_SUPPORT· 542

PFILTER_IF_RES_CONFLICT· 543

PFILTER_IF_UNK_ERR·· 543

PFILTER_IPV4_FLOW_INFO·· 544

PFILTER_IPV4_FLOW_STATIS· 544

PFILTER_IPV6_FLOW_INFO·· 545

PFILTER_IPV6_FLOW_STATIS· 545

PFILTER_IPV6_STATIS_INFO·· 546

PFILTER_MAC_FLOW_INFO·· 546

PFILTER_STATIS_INFO·· 547

PFILTER_VLAN_IPV4_DACT_NO_RES· 547

PFILTER_VLAN_IPV4_DACT_UNK_ERR·· 548

PFILTER_VLAN_IPV6_DACT_NO_RES· 548

PFILTER_VLAN_IPV6_DACT_UNK_ERR·· 549

PFILTER_VLAN_MAC_DACT_NO_RES· 549

PFILTER_VLAN_MAC_DACT_UNK_ERR·· 550

PFILTER_VLAN_NO_RES· 550

PFILTER_VLAN_NOT_SUPPORT· 551

PFILTER_VLAN_RES_CONFLICT· 551

PFILTER_VLAN_UNK_ERR·· 552

PIM messages· 553

PIM_NBR_DOWN·· 553

PIM_NBR_UP· 553

PING messages· 554

PING_STATISTICS· 554

PING_VPN_STATISTICS· 555

PKG messages· 556

PKG_BOOTLOADER_FILE_FAILED·· 556

PKG_BOOTLOADER_FILE_SUCCESS· 556

PKG_INSTALL_ACTIVATE_FAILED·· 556

PKG_INSTALL_ACTIVATE_SUCCESS· 557

PKI messages· 558

GET_CERT_FROM_CA_SERVER_FAIL· 558

IMPORT_CERT_FAIL· 559

REQUEST_CERT_FAIL· 560

REQUEST_CERT_SUCCESS· 561

RETRIEVE_CRL_FAIL· 561

VALIDATE_CERT_FAIL· 562

PKT2CPU messages· 564

PKT2CPU_NO_RESOURCE· 564

PKTCPT· 565

PKTCPT_AP_OFFLINE· 565

PKTCPT_AREADY_EXIT· 565

PKTCPT_CONN_FAIL· 566

PKTCPT_INVALID_FILTER·· 566

PKTCPT_LOGIN_DENIED·· 566

PKTCPT_MEMORY_ALERT· 567

PKTCPT_OPEN_FAIL· 567

PKTCPT_OPERATION_TIMEOUT· 567

PKTCPT_SERVICE_FAIL· 568

PKTCPT_UNKNOWN_ERROR·· 568

PKTCPT_UPLOAD_ERROR·· 568

PKTCPT_WRITE_FAIL· 569

Portal messages· 570

PORTAL_RULE_FAILED·· 570

PORTSEC messages· 571

PORTSEC_ACL_FAILURE· 571

PORTSEC_CAR_FAILURE· 571

PORTSEC_CREATEAC_FAILURE· 572

PORTSEC_LEARNED_MACADDR·· 572

PORTSEC_NTK_NOT_EFFECTIVE· 573

PORTSEC_PORTMODE_NOT_EFFECTIVE· 573

PORTSEC_PROFILE_FAILURE· 573

PORTSEC_URL_FAILURE· 574

PORTSEC_VIOLATION·· 574

PPP messages· 575

IPPOOL_ADDRESS_EXHAUSTED·· 575

PPP_USER_LOGON_SUCCESS· 575

PPP_USER_LOGON_FAILED·· 576

PPP_USER_LOGOFF· 576

PWDCTL messages· 578

ADDBLACKLIST· 578

CHANGEPASSWORD·· 578

FAILEDTOWRITEPWD·· 579

FAILEDTOOPENFILE· 579

NOENOUGHSPACE· 579

QOS messages· 580

MIRROR_SYNC_CFG_FAIL· 580

QOS_CAR_APPLYUSER_FAIL· 580

QOS_CBWFQ_REMOVED·· 581

QOS_GTS_APPLYUSER_FAIL· 581

QOS_NOT_ENOUGH_BANDWIDTH·· 582

QOS_POLICY_APPLYCOPP_CBFAIL· 582

QOS_POLICY_APPLYCOPP_FAIL· 583

QOS_POLICY_APPLYGLOBAL_CBFAIL· 583

QOS_POLICY_APPLYGLOBAL_FAIL· 584

QOS_POLICY_APPLYIF_CBFAIL· 584

QOS_POLICY_APPLYIF_FAIL· 585

QOS_POLICY_APPLYUSER_FAIL· 585

QOS_POLICY_APPLYVLAN_CBFAIL· 586

QOS_POLICY_APPLYVLAN_FAIL· 586

QOS_QMPROFILE_APPLYUSER_FAIL· 587

QOS_QMPROFILE_MODIFYQUEUE_FAIL· 587

WRED_TABLE_CFG_FAIL· 588

RADIUS messages· 589

RADIUS_AUTH_FAILURE· 589

RADIUS_AUTH_SUCCESS· 589

RADIUS_DELETE_HOST_FAIL· 589

RDDC messages· 590

RDDC_ACTIVENODE_CHANGE· 590

RESMON· 591

RESMON_MINOR·· 591

RESMON_MINOR_RECOVERY· 592

RESMON_SEVERE· 592

RESMON_SEVERE_RECOVERY· 593

RESMON_USEDUP· 593

RESMON_USEDUP_RECOVERY· 594

RIP messages· 595

RIP_MEM_ALERT· 595

RIP_RT_LMT· 595

RIPNG messages· 596

RIPNG_MEM_ALERT· 596

RIPNG_RT_LMT· 596

RM messages· 597

RM_ACRT_REACH_LIMIT· 597

RM_ACRT_REACH_THRESVALUE· 597

RM_THRESHLD_VALUE_REACH·· 598

RM_TOTAL_THRESHLD_VALUE_REACH·· 598

RPR messages· 599

RPR_EXCEED_MAX_SEC_MAC·· 599

RPR_EXCEED_MAX_SEC_MAC_OVER·· 599

RPR_EXCEED_MAX_STATION·· 600

RPR_EXCEED_MAX_STATION_OVER·· 600

RPR_EXCEED_RESERVED_RATE· 600

RPR_EXCEED_RESERVED_RATE_OVER·· 601

RPR_IP_DUPLICATE· 601

RPR_IP_DUPLICATE_OVER·· 601

RPR_JUMBO_INCONSISTENT· 602

RPR_JUMBO_INCONSISTENT_OVER·· 602

RPR_MISCABLING·· 602

RPR_MISCABLING_OVER·· 603

RPR_PROTECTION_INCONSISTENT· 603

RPR_PROTECTION_INCONSISTENT_OVER·· 603

RPR_SEC_MAC_DUPLICATE· 604

RPR_SEC_MAC_DUPLICATE_OVER·· 604

RPR_TOPOLOGY_INCONSISTENT· 604

RPR_TOPOLOGY_INCONSISTENT_OVER·· 605

RPR_TOPOLOGY_INSTABILITY· 605

RPR_TOPOLOGY_INSTABILITY_OVER·· 605

RPR_TOPOLOGY_INVALID·· 606

RPR_TOPOLOGY_INVALID_OVER·· 606

RRPP messages· 607

RRPP_RING_FAIL· 607

RRPP_RING_RESTORE· 607

RTM messages· 608

RTM_TCL_NOT_EXIST· 608

RTM_TCL_MODIFY· 608

RTM_TCL_LOAD_FAILED·· 608

SCM messages· 609

PROCESS_ABNORMAL· 609

PROCESS_ACTIVEFAILED·· 609

SCM_ABNORMAL_REBOOT· 610

SCM_ABNORMAL_REBOOTMDC·· 610

SCM_ABORT_RESTORE· 611

SCM_INSMOD_ADDON_TOOLONG·· 611

SCM_KERNEL_INIT_TOOLONG·· 611

SCM_PROCESS_STARTING_TOOLONG·· 612

SCM_PROCESS_STILL_STARTING·· 612

SCM_SKIP_PROCESS· 613

SCM_SKIP_PROCESS· 613

SCRLSP messages· 614

SCRLSP_LABEL_DUPLICATE· 614

SESSION messages· 615

SESSION_IPV4_FLOW·· 615

SESSION_IPV6_FLOW·· 616

SFLOW messages· 618

SFLOW_HARDWARE_ERROR·· 618

SHELL messages· 619

SHELL_CMD·· 619

SHELL_CMD_CONFIRM·· 619

SHELL_CMD_EXECUTEFAIL· 620

SHELL_CMD_INPUT· 620

SHELL_CMD_INPUT_TIMEOUT· 620

SHELL_CMD_MATCHFAIL· 621

SHELL_CMDDENY· 621

SHELL_CMDFAIL· 621

SHELL_CRITICAL_CMDFAIL· 622

SHELL_LOGIN·· 622

SHELL_LOGOUT· 622

SLSP messages· 623

SLSP_LABEL_DUPLICATE· 623

SMLK messages· 624

SMLK_LINK_SWITCH·· 624

SNMP messages· 625

SNMP_ACL_RESTRICTION·· 625

SNMP_AUTHENTICATION_FAILURE· 625

SNMP_GET· 626

SNMP_NOTIFY· 626

SNMP_SET· 627

SNMP_USM_NOTINTIMEWINDOW·· 627

SSHC messages· 628

SSHC_ALGORITHM_MISMATCH·· 628

SSHC_AUTH_PASSWORD_FAIL· 628

SSHC_AUTH_PUBLICKEY_FAIL· 629

SSHC_CERT_VERIFY_FAIL· 629

SSHC_CONNECT_FAIL· 630

SSHC_DECRYPT_FAIL· 631

SSHC_DISCONNECT· 631

SSHC_ENCRYPT_FAIL· 631

SSHC_HOST_NAME_ERROR·· 632

SSHC_KEY_EXCHANGE_FAIL· 632

SSHC_MAC_ERROR·· 632

SSHC_PUBLICKEY_NOT_EXIST· 633

SSHC_VERSION_MISMATCH·· 633

SSHS messages· 634

SSHS_ACL_DENY· 634

SSHS_ALGORITHM_MISMATCH·· 634

SSHS_AUTH_EXCEED_RETRY_TIMES· 635

SSHS_AUTH_FAIL· 635

SSHS_AUTH_TIMEOUT· 635

SSHC_CERT_VERIFY_FAIL· 636

SSHS_CONNECT· 637

SSHS_DECRYPT_FAIL· 637

SSHS_DISCONNECT· 638

SSHS_ENCRYPT_FAIL· 638

SSHS_LOG·· 639

SSHS_MAC_ERROR·· 639

SSHS_REACH_SESSION_LIMIT· 640

SSHS_REACH_USER_LIMIT· 640

SSHS_SCP_OPER·· 640

SSHS_SFTP_OPER·· 641

SSHS_SRV_UNAVAILABLE· 641

SSHS_VERSION_MISMATCH·· 642

STAMGR messages· 643

STAMGR_ADD_FAILVLAN·· 643

STAMGR_ADDBAC_INFO·· 643

STAMGR_ADDSTA_INFO·· 643

STAMGR_AUTHORACL_FAILURE· 644

STAMGR_AUTHORUSERPROFILE_FAILURE· 644

STAMGR_CLIENT_OFFLINE· 645

STAMGR_CLIENT_ONLINE· 645

STAMGR_DELBAC_INFO·· 645

STAMGR_DELSTA_INFO·· 646

STAMGR_DOT1X_LOGIN_FAILURE· 646

STAMGR_DOT1X_LOGIN_SUCC·· 647

STAMGR_DOT1X_LOGOFF· 647

STAMGR_MACA_LOGIN_FAILURE· 648

STAMGR_MACA_LOGIN_SUCC·· 649

STAMGR_MACA_LOGOFF· 649

STAMGR_STAIPCHANGE_INFO·· 650

STAMGR_TRIGGER_IP· 650

STM messages· 651

STM_AUTO_UPDATE_FAILED·· 651

STM_AUTO_UPDATE_FAILED·· 652

STM_AUTO_UPDATE_FINISHED·· 652

STM_AUTO_UPDATE_FINISHED·· 653

STM_AUTO_UPDATING·· 653

STM_AUTO_UPDATING·· 653

STM_LINK_DOWN·· 654

STM_LINK_MERGE· 654

STM_LINK_TIMEOUT· 654

STM_LINK_UP· 655

STM_MERGE_NEED_REBOOT· 655

STM_MERGE_NOT_NEED_REBOOT· 655

STM_SAMEMAC·· 656

STM_SOMER_CHECK· 656

STP messages· 657

STP_BPDU_PROTECTION·· 657

STP_BPDU_RECEIVE_EXPIRY· 657

STP_CONSISTENCY_RESTORATION·· 658

STP_DETECTED_TC·· 658

STP_DISABLE· 658

STP_DISCARDING·· 659

STP_DISPUTE· 659

STP_ENABLE· 660

STP_FORWARDING·· 660

STP_LOOP_PROTECTION·· 660

STP_LOOPBACK_PROTECTION·· 661

STP_NOT_ROOT· 661

STP_NOTIFIED_TC·· 661

STP_PORT_TYPE_INCONSISTENCY· 662

STP_PVID_INCONSISTENCY· 662

STP_PVST_BPDU_PROTECTION·· 662

STP_ROOT_PROTECTION·· 663

SYSLOG messages· 665

SYSLOG_LOGFILE_FULL· 665

SYSLOG_NO_SPACE· 665

SYSLOG_RESTART· 665

SYSLOG_RTM_EVENT_BUFFER_FULL· 666

TACACS messages· 667

TACACS_AUTH_FAILURE· 667

TACACS_AUTH_SUCCESS· 667

TACACS_DELETE_HOST_FAIL· 667

TELNETD messages· 668

TELNETD_ACL_DENY· 668

TELNETD_REACH_SESSION_LIMIT· 668

TRILL messages· 669

TRILL_DUP_SYSTEMID·· 669

TRILL_INTF_CAPABILITY· 669

TRILL_LICENSE_EXPIRED·· 670

TRILL_LICENSE_EXPIRED_TIME· 670

TRILL_LICENSE_UNAVAILABLE· 670

TRILL_MEM_ALERT· 671

TRILL_NBR_CHG·· 671

VCF messages· 672

VCF_AGGR_CREAT· 672

VCF_AGGR_DELETE· 672

VCF_AGGR_FAILED·· 673

VCF_AUTO_ANALYZE_USERDEF· 673

VCF_AUTO_NO_USERDEF· 674

VCF_AUTO_START· 674

VCF_AUTO_STATIC_CMD·· 675

VCF_BGP· 675

VCF_DOWN_LINK· 676

VCF_GET_IMAGE· 676

VCF_GET_TEMPLATE· 677

VCF_INSTALL_IMAGE· 677

VCF_IRF_FINISH·· 678

VCF_IRF_FOUND·· 678

VCF_IRF_REBOOT· 679

VCF_IRF_START· 679

VCF_LOOPBACK_START· 680

VCF_LOOPBACK_START_FAILED·· 680

VCF_LOOPBACK_ALLOC·· 681

VCF_LOOPBACK_NO_FREE_IP· 681

VCF_LOOPBACK_RECLAIM·· 682

VCF_REBOOT· 682

VCF_SKIP_INSTALL· 683

VCF_STATIC_CMD_ERROR·· 683

VCF_UP_LINK· 684

VLAN messages· 685

VLAN_CREATEVLAN_NO_ENOUGH_RESOUR·· 685

VLAN_FAILED·· 685

VLAN_VLANMAPPING_FAILED·· 686

VLAN_VLANTRANSPARENT_FAILED·· 686

VRRP messages· 687

VRRP_STATUS_CHANGE· 687

VRRP_VF_STATUS_CHANGE· 688

VRRP_VMAC_INEFFECTIVE· 688

VSRP messages· 689

VSRP_BIND_FAILED·· 689

VXLAN messages· 690

VXLAN_LICENSE_UNAVAILABLE· 690

WIPS messages· 691

APFLOOD·· 691

AP_CHANNEL_CHANGE· 691

ASSOCIATEOVERFLOW·· 691

HONEYPOT· 692

HTGREENMODE· 692

MAN_IN_MIDDLE· 692

WIPS_DOS· 693

WIPS_FLOOD·· 693

WIPS_MALF· 694

WIPS_SPOOF· 695

WIPS_WEAKIV· 695

WIRELESSBRIDGE· 696

 


Introduction

This document includes all system messages for Comware 7 software. It is intended for system administrators who are responsible for managing Comware 7 systems.

This document assumes that the readers are familiar with data communications technologies and H3C networking products.

System log message format

By default, the system log messages use one of the following formats depending on the output destination:

·     Log host:

<PRI>TIMESTAMP Sysname %%vendorMODULE/severity/MNEMONIC: location; CONTENT

·     Destinations except for the log host:

Prefix TIMESTAMP Sysname MODULE/severity/MNEMONIC: CONTENT

Table 1 System log message elements

Element

Description

<PRI>

Priority identifier. It is calculated by using the following formula:

Priority identifier=facilityx8+severity

Where:

·     Facility is specified by using the info-center loghost command. A log host uses this parameter to identify log sources and filter log messages.

·     Severity represents the importance of the message. For more information about severity levels, see Table 2.

Prefix

Message type identifier. This element is contained in the system log messages sent to non-log host destinations.

The element uses the following symbols to indicate message severity:

·     Percentage sign (%)—Informational and higher levels.

·     Asterisk (*)—Debug level.

TIMESTAMP

Date and time when the event occurred.

The following are commands for configuring the timestamp format:

·     Log host—Use the info-center timestamp loghost command.

·     Non-log host destinationsUse the info-center timestamp command.

Sysname

Name or IP address of the device that generated the message.

%%vendor

Manufacturer flag. This element is %%10 for H3C.

This element is only available in messages sent to the log host.

MODULE

Name of the module that produced the message.

severity

Severity level of the message. (For more information about severity levels, see Table 2.)

MNEMONIC

Text string that uniquely identifies the system message. The maximum length is 32 characters.

location

Optional. This element presents location information for the message in the following format:

-attribute1=x-attribute2=y…-attributeN=z

This element is separated from the message description by using a semicolon (;).

CONTENT

Text string that contains detailed information about the event or error.

For variable fields in this element, this document uses the representations in Table 3.

 

System log messages are classified into eight severity levels from 0 to 7. The lower the number, the higher the severity, as shown in Table 2.

Table 2 System log message severity levels

Level

Severity

Description

0

Emergency

The system is unusable. For example, the system authorization has expired.

1

Alert

Action must be taken immediately. For example, traffic on an interface exceeds the upper limit.

2

Critical

Critical condition. For example, the device temperature exceeds the upper limit, the power module fails, or the fan tray fails.

3

Error

Error condition. For example, the link state changes or a storage card is unplugged.

4

Warning

Warning condition. For example, an interface is disconnected, or the memory resources are used up.

5

Notification

Normal but significant condition. For example, a terminal logs in to the device, or the device reboots.

6

Informational

Informational message. For example, a command or a ping operation is executed.

7

Debug

Debugging message.

 

For variable fields in the message text, this document uses the representations in Table 3. The values are case insensitive, even though the representations are uppercase letters.

Table 3 Variable field representations

Representation

Information type

INT16

Signed 16-bit decimal number.

UINT16

Unsigned 16-bit decimal number.

INT32

Signed 32-bit decimal number.

UINT32

Unsigned 32-bit decimal number.

INT64

Signed 64-bit decimal number.

UINT64

Unsigned 64-bit decimal number.

DOUBLE

Two dot-separated signed 32-bit decimal numbers. The format is [INTEGER].[INTEGER].

HEX

Hexadecimal number.

CHAR

Single character.

STRING

Character string.

IPADDR

IP address.

MAC

MAC address.

DATE

Date.

TIME

Time.

 

Managing and obtaining system log messages

You can manage system log messages by using the information center.

By default, the information center is enabled. Log messages can be output to the console, log buffer, monitor terminal, log host, and log file.

To filter log messages, use the info-center source command to specify log output rules. A log output rule specifies the source modules and the lowest severity level of log messages that can be output to a destination. A log message is output if its severity level is higher than or equal to the specified level. For example, if you specify a severity level of 6 (informational), log messages that have a severity level from 0 to 6 are output.

For more information about using the information center, see the network management and monitoring configuration guide for the product.

Obtaining log messages from the console terminal

Access the device through the console port. Real-time log messages are displayed on the console terminal.

Obtaining log messages from the log buffer

Use the display logbuffer command to display history log messages in the log buffer.

Obtaining log messages from a monitor terminal

Monitor terminals refer to terminals that access the device through the AUX, VTY, or TTY lines (for example, Telnet). To obtain log messages from a monitor terminal, use the following guidelines:

·     To display log messages on the monitor terminal, you must configure the terminal monitor command.

·     For monitor terminals, the lowest level of log messages that can be displayed is determined by both the terminal logging level and info-center source commands.

Obtaining log messages from the log file

By default, the log file feature automatically saves logs from the log file buffer to the log file every 24 hours. You can use the info-center logfile frequency command to change the automatic saving internal.

To manually save logs to the log file, use the logfile save command. The log file buffer is cleared each time a save operation is performed.

By default, you can obtain the log file from the flash:/logfile/ path.

Obtaining log messages from a log host

Use the info-center loghost command to specify the service port number and IP address of a log host. To specify multiple log hosts, repeat the command.

For a successful log message transmission, make sure the specified port number is the same as the port number used on the log host. The default service port number is 514.

Software module list

Table 4 lists all software modules that might produce system log messages. This document uses "OPENSRC" to represent all open source modules.

Table 4 Software module list

Module name representation

Module name expansion

AAA

Authentication, Authorization and Accounting

ACL

Access Control List

ANCP

Access Node Control Protocol

APMGR

Access Point Management

ARP

Address Resolution Protocol

ATK

Attack Detection and Prevention

ATM

Asynchronous Transfer Mode

BFD

Bidirectional Forwarding Detection

BGP

Border Gateway Protocol

BLS

Blacklist

CFD

Connectivity Fault Detection

CFGMAN

Configuration Management

CONNLMT

Connection Limit

DEV

Device Management

DHCP

Dynamic Host Configuration Protocol

DHCPR

IPv4 DHCP Relay

DHCPS

DHCP Server

DHCPS6

DHCPv6 Server

DHCPSP4

DHCP Snooping

DHCPSP6

DHCPv6 Snooping

DIAG

Diagnosis

DLDP

Device Link Detection Protocol

DOT1X

802.1X

DRNI

Distributed Resilient Network Interconnect

EDEV

Extended-Device Management

ERPS

Ethernet Ring Protection Switching

ETHOAM

Ethernet Operation, Administration and Maintenance

EVB

Edge Virtual Bridging

EVIISIS

Ethernet Virtual Interconnect Intermediate System-to-Intermediate System

FCOE

Fibre Channel Over Ethernet

FCLINK

Fibre Channel Link

FCZONE

Fibre Channel Zone

FIB

Forwarding Information Base

FILTER

Filter

FIPS

FIP Snooping

FTPD

File Transfer Protocol Daemon

HA

High Availability

HQOS

Hierarchical QoS

HTTPD

Hypertext Transfer Protocol Daemon

IFNET

Interface Net Management

IKE

Internet Key Exchange

IPFW

IP Forwarding

IPSEC

IP Security

IPSG

IP Source Guard

IRDP

ICMP Router Discovery Protocol

ISIS

Intermediate System-to-Intermediate System

ISSU

In-Service Software Upgrade

L2TP

Layer 2 Tunneling Protocol

L2VPN

Layer 2 VPN

LAGG

Link Aggregation

LDP

Label Distribution Protocol

LLDP

Link Layer Discovery Protocol

LOAD

Load Management

LOGIN

Login

LPDT

Loopback Detection

LS

Local Server

LSPV

LSP Verification

MAC

Media Access Control

MACA

MAC Authentication

MACSEC

MAC Security

MBFD

MPLS BFD

MBUF

Memory buffer

MDC

Multitenant Device Context

MFIB

Multicast Forwarding Information Base

MGROUP

Mirroring group

MPLS

Multiprotocol Label Switching

MTLK

Monitor Link

NAT

Network Address Translation

NETCONF

Network Configuration Protocol

ND

Neighbor Discovery

NQA

Network Quality Analyzer

NTP

Network Time Protocol

OPENSRC

Open Source

OBJP

Object Policy

OFP

OpenFlow Protocol

OPTMOD

Optical Module

OSPF

Open Shortest Path First

OSPFV3

Open Shortest Path First Version 3

PKTCPT

Packet Capture

PFILTER

Packet Filter

PBB

Provider Backbone Bridge

PBR

Policy-Based Routing

PCE

Path Computation Element

PEX

Port Extender

PIM

Protocol Independent Multicast

PING

Packet Internet Groper

PKI

Public Key Infrastructure

PKT2CPU

Packet to CPU

PORTSEC

Port Security

PPP

Point to Point Protocol

PWDCTL

Password Control

QOS

Quality of Service

RADIUS

Remote Authentication Dial In User Service

RDDC

Redundancy

RIP

Routing Information Protocol

RIPNG

Routing Information Protocol Next Generation

RM

Routing Management

RRPP

Rapid Ring Protection Protocol

RTM

Real-Time Event Manager

SCM

Service Control Manager

SCRLSP

Static CRLSP

SESSION

Session

SFLOW

Sampler Flow

SHELL

Shell

SLSP

Static LSP

SMLK

Smart Link

SNMP

Simple Network Management Protocol

SSHC

Secure Shell Client

SSHS

Secure Shell Server

STAMGR

Station Management

STM

Stack Topology Management

STP

Spanning Tree Protocol

SYSEVENT

System Event

SYSLOG

System Log

TACACS

Terminal Access Controller Access Control System

TELNETD

Telnet Daemon

TRILL

Transparent Interconnect of Lots of Links

VCF

Vertical Converged Framework

VLAN

Virtual Local Area Network

VRRP

Virtual Router Redundancy Protocol

VSRP

Virtual Service Redundancy Protocol

VXLAN

Virtual eXtensible LAN

WIPS

Wireless Intrusion Prevention System

 

Using this document

This document categorizes system log messages by software module. The modules are ordered alphabetically. Except for OPENSRC, the system log messages for each module are listed in alphabetic order of their mnemonic names. The OPENSRC messages are unordered because they use the same mnemonic name (SYSLOG). For each OPENSRC message, the section title uses a short description instead of the mnemonic name.

This document explains messages in tables. Table 5 describes information provided in these tables.

Table 5 Message explanation table contents

Item

Content

Example

Message text

Presents the message description.

ACL [UINT32] [STRING] [UINT64] packet(s).

Variable fields

Briefly describes the variable fields in the order that they appear in the message text.

The variable fields are numbered in the "$Number" form to help you identify their location in the message text.

$1: ACL number.

$2: ID and content of an ACL rule.

$3: Number of packets that matched the rule.

Severity level

Provides the severity level of the message.

6

Example

Provides a real message example. The examples do not include the "<PRI>TIMESTAMP Sysname %%vendor" part or the "Prefix TIMESTAMP Sysname" part, because information in this part varies with system settings.

ACL/6/ACL_STATIS_INFO: ACL 2000 rule 0 permit source 1.1.1.1 0 logging 10000 packet(s).

Explanation

Explains the message, including the event or error cause.

Number of packets that matched an ACL rule. This message is sent when the packet counter changes.

Recommended action

Provides recommended actions. For informational messages, no action is required.

No action is required.

 

 


AAA messages

This section contains AAA messages.

AAA_FAILURE

Message text

-AAAType=[STRING]-AAADomain=[STRING]-Service=[STRING]-UserName=[STRING]; AAA failed.

Variable fields

$1: AAA type.

$2: AAA scheme.

$3: Service.

$4: Username.

Severity level

5

Example

AAA/5/AAA_FAILURE: -AAAType=AUTHOR-AAADomain=domain1-Service=login-UserName=cwf@system; AAA failed.

Explanation

An AAA request was rejected.

The following are the common reasons:

·     No response was received from the server.

·     The username or password was incorrect.

·     The service type that the user applied for was incorrect.

Recommended action

1.     Verify that the device is correctly connected to the server.

2.     Enter the correct username and password.

3.     Verify that the server settings are the same as the settings on the device.

4.     If the problem persists, contact H3C Support.

 

AAA_LAUNCH

Message text

-AAAType=[STRING]-AAADomain=[STRING]-Service=[STRING]-UserName=[STRING]; AAA launched.

Variable fields

$1: AAA type.

$2: AAA scheme.

$3: Service.

$4: Username.

Severity level

6

Example

AAA/6/AAA_LAUNCH: -AAAType=AUTHEN-AAADomain=domain1-Service=login-UserName=cwf@system; AAA launched.

Explanation

An AAA request was received.

Recommended action

No action is required.

 

AAA_SUCCESS

Message text

-AAAType=[STRING]-AAADomain=[STRING]-Service=[STRING]-UserName=[STRING]; AAA succeeded.

Variable fields

$1: AAA type.

$2: AAA scheme.

$3: Service.

$4: Username.

Severity level

6

Example

AAA/6/AAA_SUCCESS: -AAAType=AUTHOR-AAADomain=domain1-Service=login-UserName=cwf@system; AAA succeeded.

Explanation

An AAA request was accepted.

Recommended action

No action is required.

 

 


ACL messages

This section contains ACL messages.

ACL_ACCELERATE_NO_RES

Message text

Failed to accelerate [STRING] ACL [UINT32]. The resources are insufficient.

Variable fields

$1: ACL type.

$2: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NO_RES: Failed to accelerate IPv6 ACL 2001. The resources are insufficient.

Explanation

Hardware resources were insufficient for accelerating an ACL.

Recommended action

Delete some rules or disabled ACL acceleration for other ACLs to release hardware resources.

 

ACL_ACCELERATE_NONCONTIGUOUSMASK

Message text

Failed to accelerate ACL [UINT32]. ACL acceleration supports only contiguous wildcard masks.

Variable fields

$1: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NONCONTIGUOUSMASK: Failed to accelerate ACL 2001. ACL acceleration supports only contiguous wildcard masks.

Explanation

ACL acceleration failed because rules containing noncontiguous wildcard masks exist in the ACL.

Recommended action

Check the ACL rules and delete the unsupported configuration.

 

ACL_ACCELERATE_NOT_SUPPORT

Message text

Failed to accelerate [STRING] ACL [UINT32]. The operation is not supported.

Variable fields

$1: ACL type.

$2: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NOT_SUPPORT: Failed to accelerate IPv6 ACL 2001. The operation is not supported.

Explanation

ACL acceleration failed because the system does not support ACL acceleration.

Recommended action

No action is required.

 

ACL_ACCELERATE_NOT_SUPPORTHOPBYHOP

Message text

Failed to accelerate IPv6 ACL [UINT32]. ACL acceleration does not support the rules that contain the hop-by-hop keywords.

Variable fields

$1: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NOT_SUPPORTHOPBYHOP: Failed to accelerate IPv6 ACL 2001. ACL acceleration does not support the rules that contain the hop-by-hop keywords.

Explanation

ACL acceleration failed for the IPv6 ACL because rules containing the hop-by-hop keyword exist in the ACL.

Recommended action

Check the ACL rules and delete the unsupported configuration.

 

ACL_ACCELERATE_NOT_SUPPORTMULTITCPFLAG

Message text

Failed to accelerate IPv6 ACL [UINT32]. ACL acceleration does not support specifying multiple TCP flags in one rule.

Variable fields

$1: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NOT_SUPPORTMULTITCPFLAG: Failed to accelerate IPv6 ACL 2001. ACL acceleration does not support specifying multiple TCP flags in one rule.

Explanation

ACL acceleration failed for the IPv6 ACL because rules containing multiple TCP flags exist in the ACL.

Recommended action

Check the ACL rules and delete the unsupported configuration.

 

ACL_ACCELERATE_UNK_ERR

Message text

Failed to accelerate [STRING] ACL [UINT32].

Variable fields

$1: ACL type.

$2: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_UNK_ERR: Failed to accelerate IPv6 ACL 2001.

Explanation

ACL acceleration failed because of an unknown error.

Recommended action

No action is required.

 

ACL_IPV6_STATIS_INFO

Message text

IPv6 ACL [UINT32] [STRING] [UINT64] packet(s).

Variable fields

$1: ACL number.

$2: ID and content of an IPv6 ACL rule.

$3: Number of packets that matched the rule.

Severity level

6

Example

ACL6/6/ACL_IPV6_STATIS_INFO: IPv6 ACL 2000 rule 0 permit source 1:1::/64 logging 1000 packet(s).

Explanation

The number of packets matching the IPv6 ACL rule changed.

Recommended action

No action is required.

 

ACL_NO_MEM

Message text

Failed to configure [STRING] ACL [UINT] due to lack of memory.

Variable fields

$1: ACL type.

$2: ACL number.

Severity level

3

Example

ACL/3/ACL_NO_MEM: Failed to configure ACL 2001 due to lack of memory.

Explanation

Configuring the ACL failed because memory is insufficient.

Recommended action

Use the display memory-threshold command to check the memory usage.

 

ACL_STATIS_INFO

Message text

ACL [UINT32] [STRING] [UINT64] packet(s).

Variable fields

$1: ACL number.

$2: ID and content of an IPv4 ACL rule.

$3: Number of packets that matched the rule.

Severity level

6

Example

ACL/6/ACL_STATIS_INFO: ACL 2000 rule 0 permit source 1.1.1.1 0 logging 10000 packet(s).

Explanation

The number of packets matching the IPv4 ACL rule changed.

Recommended action

No action is required.

 

 


ANCP messages

This section contains ANCP messages.

ANCP_INVALID_PACKET

Message text

-NeighborName=[STRING]-State=[STRING]-MessageType=[STRING]; The [STRING] value [STRING] is wrong, and the value [STRING] is expected.

Variable fields

$1: ANCP neighbor name.

$2: Neighbor state.

$3: Message type.

$4: Field.

$5: Wrong value of the field.

$6: Expected value of the field.

Severity level

6

Example

ANCP/6/ANCP_INVALID_PACKET: -NeighborName=Dslam-State=SYNSENT-MessageType=SYNACK; The Sender Instance value 0 is wrong, and the value 1 is expected.

Explanation

The system received an adjacency message that had a field with a wrong value.

Recommended action

No action is required.

 

 


APMGR messages

This section contains access point management messages.

APMGR_AC_MEM_ALERT

Message text

The memory utilization has reached the threshold.

Variable fields

N/A

Severity level

4

Example

APMGR/4/APMGR_AC_MEM_ALERT: The memory utilization has reached the threshold.

Explanation

The AP failed to come online because the memory utilization exceeded the limit.

Recommended action

Stop creating manual APs and prevent APs from coming online.

 

APMGR_ADD_AP_FAIL

Message text

AP [STRING] failed to come online using serial ID [STRING]: MAC address [STRING] is being used by AP [STRING].

Variable fields

$1: AP name.

$2: Serial ID.

$3: MAC address.

$4: AP name.

Severity level

4

Example

APMGR/4/ APMGR_ADD_AP_FAIL: AP ap1 failed to come online using serial ID 01247ef96: MAC address 0023-7961-5201 is being used by AP ap2.

Explanation

The AP failed to come online because a manual AP that has the same MAC address already exists on the AC.

Recommended action

Delete either the manual AP that has the MAC address or the serial ID.

 

APMGR_ADDBAC_INFO

Message text

Add BAS AC [STRING].

Variable fields

$1: MAC address of the BAS AC.

Severity level

6

Example

APMGR/6/APMGR_ADDBAC_INFO: Add BAS AC 3ce5-a616-28cd.

Explanation

The BAS AC was connected to the master AC.

Recommended action

No action is required.

 

APMGR_AP_OFFLINE

Message text

AP [STRING] went offline. State changed to Idle.

Variable fields

$1: AP name.

Severity level

6

Example

APMGR/6/APMGR_AP_OFFLINE: AP ap1 went offline. State changed to Idle.

Explanation

The AP went offline. The state of the AP changed to Idle.

Recommended action

If the AP went offline abnormally, check the debugging information to locate the issue and resolve it.

 

APMGR_AP_ONLINE

Message text

AP [STRING] went online. State changed to Run.

Variable fields

$1: AP name.

Severity level

6

Example

APMGR/6/APMGR_AP_ONLINE: AP ap1 went online. State changed to Run.

Explanation

The AP came online. The state of the AP changed to Run.

Recommended action

No action is required.

 

APMGR_CWC_IMG_DOWNLOAD_COMPLETE

Message text

System software image file [STRING] downloading through the CAPWAP tunnel to AC [STRING] completed.

Variable fields

$1: Image file name.

$2: AC IP address.

Severity level

6

Example

APMGR/6/APMGR_CWC_IMG_DOWNLOAD_COMPLETE: System software image file 5800.ipe downloading through the CAPWAP tunnel to AC 192.168.10.1 completed.

Explanation

The AP downloaded the image file from the AC successfully.

Recommended action

No action is required.

 

APMGR_CWC_IMG_DOWNLOAD_START

Message text

Started to download the system software image file [STRING] through the CAPWAP tunnel to AC [STRING].

Variable fields

$1: Image file name.

$2: AC IP address.

Severity level

6

Example

APMGR/6/APMGR_CWC_IMG_DOWNLOAD_START: Started to download the system software image file 5800.ipe through the CAPWAP tunnel to AC 192.168.10.1.

Explanation

The AP started to download the image file from the AC.

Recommended action

Make sure the AP is correctly connected to the AC.

 

APMGR_CWC_IMG_NO_ENOUGH_SPACE

Message text

Insufficient flash memory space for downloading system software image file [STRING].

Variable fields

$1: Image file name.

Severity level

6

Example

APMGR/6/APMGR_CWC_IMG_NO_ENOUGH_SPACE: Insufficient flash memory space for downloading system software image file 5800.ipe.

Explanation

The AP failed to download the image file from the AC because of insufficient flash memory.

Recommended action

Delete files not in use from the AP.

 

APMGR_CWC_LOCAL_AC_DOWN

Message text

CAPWAP tunnel to Central AC [STRING] went down. Reason: [STRING].

Variable fields

$1: IP address of the central AC.

$2: Reason:

·     Added local AC IP address.

·     Deleted local AC IP address.

·     Local AC interface used for CAPWAP tunnel went down.

·     Local AC config changed.

·     N/A

Severity level

4

Example

APMGR/4/APMGR_CWC_LOCAL_AC_DOWN: CAPWAP tunnel to Central AC 2.2.2.1 went down. Reason: Added local AC IP address.

Explanation

The CAPWAP tunnel between the central AC and the local AC was terminated for a specific reason.

Recommended action

To resolve the issue:

1.     Examine the network connection between the central AC and the local AC.

2.     Verify that the central AC is correctly configured.

3.     Verify that the local AC is correctly configured.

4.     If the issue persists, contact H3C Support.

 

APMGR_CWC_LOCAL_AC_UP

Message text

CAPWAP tunnel to Central AC [STRING] went up.

Variable fields

$1: IP address of the central AC.

Severity level

6

Example

APMGR/6/APMGR_CWC_LOCAL_AC_UP: CAPWAP tunnel to Central AC 2.2.2.1 went up.

Explanation

The central AC has established a CAPWAP tunnel with the local AC.

Recommended action

No action is required.

 

APMGR_CWC_REBOOT

Message text

AP in state [STRING] is rebooting. Reason: [STRING]

Variable fields

$1: AP state.

$2: Reason:

·     AP was reset.

·     Image was downloaded successfully.

·     AP stayed in idle state for a long time.

Severity level

6

Example

APMGR/6/APMGR_CWC_REBOOT: AP in State Run is rebooting. Reason: AP was reset.

Explanation

The AP rebooted for a specific reason.

Recommended action

No action is required.

 

APMGR_CWC_RUN_DOWNLOAD_COMPLETE

Message text

File [STRING] successfully downloaded through the CAPWAP tunnel to AC [STRING].

Variable fields

$1: File name.

$2: AC IP address.

Severity level

6

Example

APMGR/6/APMGR_CWC_RUN_DOWNLOAD_COMPLETE: File ac.cfg successfully downloaded through the CAPWAP tunnel to AC 192.168.10.1.

Explanation

The AP downloaded the file from the AC successfully.

Recommended action

No action is required.

 

APMGR_CWC_RUN_DOWNLOAD_START

Message text

Started to download the file [STRING] through the CAPWAP tunnel to AC [STRING].

Variable fields

$1: File name.

$2: AC IP address.

Severity level

6

Example

APMGR/6/APMGR_CWC_RUN_DOWNLOAD_START: Started to download the file ac.cfg through the CAPWAP tunnel to AC 192.168.10.1.

Explanation

The AP started to download the file from the AC.

Recommended action

Make sure the AP is correctly connected to the AC.

 

APMGR_CWC_RUN_NO_ENOUGH_SPACE

Message text

Insufficient flash memory space for downloading file [STRING].

Variable fields

$1: File name.

Severity level

6

Example

APMGR/6/APMGR_CWC_RUN_NO_ENOUGH_SPACE: Insufficient flash memory space for downloading file ac.cfg.

Explanation

The AP failed to download the file from the AC because of insufficient flash memory.

Recommended action

Delete files not in use from the AP.

 

APMGR_CWC_TUNNEL_DOWN

Message text

CAPWAP tunnel to AC [STRING] went down. Reason: [STRING].

Variable fields

$1: AC IP address.

$2: Reason:

·     Added AP IP address.

·     Deleted AP IP address.

·     AP interface used for CAPWAP tunnel went down.

·     AP config changed.

·     AP was reset.

·     Number of echo retransmission attempts exceeded the limit.

·     Full retransmission queue.

·     Data channel timer expired.

·     Backup AC IP address changed.

·     Backup tunnel changed to master tunnel.

·     Failed to change backup tunnel to master tunnel.

·     Backup method changed.

·     N/A.

Severity level

6

Example

APMGR/6/APMGR_CWC_TUNNEL_DOWN: CAPWAP tunnel to AC 192.168.10.1 went down. Reason: AP was reset.

Explanation

The CAPWAP tunnel between the AP and the AC was terminated for a specific reason.

Recommended action

Examine the network connection between the AP and the AC.

 

APMGR_CWC_TUNNEL_UP

Message text

[STRING] CAPWAP tunnel to AC [STRING] went up.

Variable fields

$1: Tunnel type:

·     Master.

·     Backup.

$2: AC IP address.

Severity level

6

Example

APMGR/6/APMGR_CWC_TUNNEL_UP: Master CAPWAP tunnel to AC 192.168.10.1 went up.

Explanation

The AP was connected to the AC successfully and entered Run state.

Recommended action

No action is required.

 

APMGR_CWS_IMG_DOWNLOAD_COMPLETE

Message text

System software image file [STRING] downloading through the CAPWAP tunnel for AP [STRING] completed.

Variable fields

$1: Image file name.

$2: AP name.

Severity level

6

Example

APMGR/6/APMGR_ CWS_IMG_DOWNLOAD_COMPLETE: System software image file 5800.ipe downloading through the CAPWAP tunnel for AP ap2 completed.

Explanation

The AP downloaded the image file from the AC successfully.

Recommended action

No action is required.

 

APMGR_CWS_IMG_DOWNLOAD_START

Message text

AP [STRING] started to download the system software image file [STRING].

Variable fields

$1: AP name.

$2: Image file name.

Severity level

6

Example

APMGR/6/APMGR_CWS_IMG_DOWNLOAD_START: AP ap1 started to download the system software image file 5800.ipe.

Explanation

The AP started to download the image file from the AC.

Recommended action

No action is required.

 

APMGR_CWS_LOCAL_AC_DOWN

Message text

CAPWAP tunnel to local AC [STRING] went down. Reason: [STRING].

Variable fields

$1: IP address of the local AC.

$2: Reason:

·     Neighbor dead timer expired.

·     Local AC was deleted.

·     Serial number changed.

·     Processed join request in Run state.

·     Failed to retransmit message.

·     N/A

Severity level

4

Example

APMGR/4/APMGR_CWS_LOCAL_AC_DOWN: CAPWAP tunnel to local AC 1.1.1.1 went down. Reason: Serial number changed.

Explanation

The CAPWAP tunnel between the central AC and the local AC was terminated for a specific reason.

Recommended action

To resolve the issue:

1.     Examine the network connection between the central AC and the local AC.

2.     Verify that the central AC is correctly configured.

3.     Verify that the local AC is correctly configured.

4.     If the issue persists, contact H3C Support.

 

APMGR_CWS_LOCAL_AC_UP

Message text

CAPWAP tunnel to local AC [STRING] went up.

Variable fields

$1: IP address of the local AC.

Severity level

6

Example

APMGR/6/APMGR_CWS_LOCAL_AC_UP: CAPWAP tunnel to local AC 1.1.1.1 went up.

Explanation

The central AC has established a CAPWAP tunnel with the local AC.

Recommended action

No action is required.

 

APMGR_CWS_RUN_DOWNLOAD_COMPLETE

Message text

File [STRING] successfully downloaded through the CAPWAP tunnel for AP [STRING].

Variable fields

$1: File name.

$2: AP name.

Severity level

6

Example

APMGR/6/APMGR_CWS_RUN_DOWNLOAD_COMPLETE: File ac.cfg successfully downloaded through the CAPWAP tunnel for AP ap2.

Explanation

The AP downloaded the file from the AC successfully.

Recommended action

No action is required.

 

APMGR_CWS_RUN_DOWNLOAD_START

Message text

AP [STRING] started to download the file [STRING].

Variable fields

$1: AP name.

$2: File name.

Severity level

6

Example

APMGR/6/APMGR_CWS_RUN_DOWNLOAD_START: AP ap1 started to download the file ac.cfg.

Explanation

The AP started to download the file from the AC.

Recommended action

No action is required.

 

APMGR_CWS_TUNNEL_DOWN

Message text

CAPWAP tunnel to AP [STRING] went down. Reason: [STRING].

Variable fields

$1: AP name.

$2: Reason:

·     Neighbor dead timer expired.

·     AP was reset.

·     AP was deleted.

·     Serial number changed.

·     Processed join request in Run state.

·     Failed to retransmit message.

·     Received WTP tunnel down event from AP.

·     Backup AC closed the backup tunnel.

·     Tunnel switched.

·     N/A.

Severity level

6

Example

APMGR/6/APMGR_CWS_TUNNEL_DOWN: CAPWAP tunnel to AP ap1 went down. Reason: AP was reset.

Explanation

The AP went offline for a specific reason.

Recommended action

To resolve the issue:

1.     Examine the network connection between the AP and the AC.

2.     Verify that the AP is correctly configured.

3.     Verify that the AC is correctly configured.

4.     If the issue persists, contact H3C Support.

 

APMGR_CWS_TUNNEL_UP

Message text

[STRING] CAPWAP tunnel to AP [STRING] went up.

Variable fields

$1: Tunnel type:

·     Master.

·     Backup.

$2: AP name.

Severity level

6

Example

APMGR/6/APMGR_CWS_TUNNEL_UP: Backup CAPWAP tunnel to AP ap1 went up.

Explanation

The AP came online and entered Run state.

Recommended action

No action is required.

 

APMGR_DELBAC_INFO

Message text

Delete BAS AC [STRING].

Variable fields

$1: MAC address of the BAS AC.

Severity level

6

Example

APMGR/6/APMGR_DELBAC_INFO: Delete BAS AC 3ce5-a616-28cd.

Explanation

The BAS AC was disconnected from the master AC.

Recommended action

No action is required.

 

APMGR_LOCAL_AC_OFFLINE

Message text

Local AC [STRING] went offline. State changed to Idle.

Variable fields

$1: Name of the local AC.

Severity level

6

Example

APMGR/6/APMGR_LOCAL_AC_OFFLINE: Local AC ac1 went offline. State changed to Idle.

Explanation

The local AC went offline. The state of the local AC changed to Idle.

Recommended action

1.     If the local AC went offline abnormally, check the debugging information to locate the issue and resolve it.

2.     If the issue persists, contact H3C Support.

 

APMGR_LOCAL_AC_ONLINE

Message text

Local AC [STRING] went online. State changed to Run.

Variable fields

$1: Name of the local AC.

Severity level

6

Example

APMGR/6/APMGR_LOCAL_AC_ONLINE: Local AC ac1 went online. State changed to Run.

Explanation

The local AC came online. The state of the local AC changed to Run.

Recommended action

No action is required.

 

 


ARP messages

This section contains ARP messages.

ARP_ACTIVE_ACK_NO_REPLY

Message text

No ARP reply from IP [STRING] was received on interface [STRING].

Variable fields

$1: IP address.

$2: Interface name.

Severity level

6

Example

ARP/6/ARP_ACTIVE_ACK_NO_REPLY: No ARP reply from IP 192.168.10.1 was received on interface GigabitEthernet1/0/1.

Explanation

The ARP active acknowledgement feature did not receive an ARP reply after it sent an ARP request to the sender IP of an ARP message.

This message indicates the risk of attacks.

Recommended action

1.     Verify that the learned ARP entries on the device are consistent with the existing legal devices. When gateways and servers are on the network, check the ARP entries for these devices first.

2.     If the ARP entries are correct and the attack continues, contact H3C Support.

 

ARP_ACTIVE_ACK_NOREQUESTED_REPLY

Message text

Interface [STRING] received from IP [STRING] an ARP reply that was not requested by the device.

Variable fields

$1: Interface name.

$2: IP address.

Severity level

6

Example

ARP/6/ARP_ACTIVE_ACK_NOREQUESTED_REPLY: Interface GigabitEthernet1/0/1 received from IP 192.168.10.1 an ARP reply that was not requested by the device.

Explanation

The ARP active acknowledgement feature received an unsolicited ARP reply from a sender IP.

This message indicates the risk of attacks.

Recommended action

No action is required. The device discards the ARP reply automatically.

 

ARP_BINDRULETOHW_FAILED

Message text

Failed to download binding rule to hardware on the interface [STRING], SrcIP [IPADDR], SrcMAC [MAC], VLAN [UINT16], Gateway MAC [MAC].

Variable fields

$1: Interface name.

$2: Source IP address.

$3: Source MAC address.

$4: VLAN ID.

$5: Gateway MAC address.

Severity level

5

Example

ARP/5/ARP_BINDRULETOHW_FAILED: Failed to download binding rule to hardware on the interface GigabitEthernet1/0/1, SrcIP 1.1.1.132, SrcMAC 0015-E944-A947, VLAN 1, Gateway MAC 00A1-B812-1108.

Explanation

The system failed to set a binding rule to the hardware on an interface. The message is sent in any of the following situations:

·     The resources are not sufficient for the operation.

·     The memory is not sufficient for the operation.

·     A hardware error occurs.

Recommended action

To resolve the problem:

1.     Execute the display qos-acl resource command to check if the ACL resources for the operation are sufficient.

?     If yes, proceed to step 2.

?     If no, delete unnecessary configuration to release ACL resources. If no configuration can be deleted, proceed to step 2.

2.     Execute the display memory command to check if the memory for the operation is sufficient.

?     If yes, proceed to step 3.

?     If no, delete unnecessary configuration to release memory. If no configuration can be deleted, proceed to step 3.

3.     Delete the configuration and perform the operation again.

 

ARP_DETECTION_LOG

Message text

Detected an ARP attack on interface [STRING]: IP [STRING], MAC [STRING], VLAN [STRING]. [UINT32] packet(s) dropped.

Variable fields

$1: Interface name.

$2: IP address.

$3: MAC address.

$4: VLAN ID.

$5: Number of dropped packets.

Severity level

5

Example

ARP/5/ARP_INSPECTION: -MDC=1; Detected an ARP attack on interface GigabitEthernet1/0/1: IP 1.1.1.1, MAC 1-1-1, VLAN 100. 2 packet(s) dropped.

Explanation

An ARP attack was detected on an interface and attack packets were dropped.

Recommended action

Check the source of the ARP attack.

 

ARP_DUPLICATE_IPADDR_DETECT

Message text

Detected an IP address conflict. The device with MAC address [STRING] connected to interface [STRING] in VSI [STRING] and the device with MAC address [STRING] connected to interface [STRING] in VSI [STRING] were using the same IP address [IPADDR].

Variable fields

$1: MAC address.

$2: Interface name. (The interface can be a tunnel interface, Layer 3 interface, or Ethernet service instance.)

$3: VSI name.

$4: MAC address.

$5: Interface name. (The interface can be a tunnel interface, Layer 3 interface, or Ethernet service instance.)

$6: VSI name.

$7: Conflicting IP address.

Severity level

6

Example

ARP/6/ ARP_DUPLICATE_IPADDR_DETECT: Detected an IP address conflict. The device with MAC address 00-00-01 connected to interface GigabitEthernet1/0/1 service-instance 1000 in VSI vpna and the device with MAC address 00-00-02 connected to interface tunnel 10 in VSI vpna were using the same IP address 192.168.1.1.

Explanation

This message is sent when an interface receives an ARP message in which the sender information conflicts with an existing ARP entry. The sender IP address is the same as the IP address in the entry, but the MAC addresses are different.

Recommended action

Change the IP address on either of the two devices.

 

ARP_DYNAMIC

Message text

The maximum number of dynamic ARP entries for the device reached.

Variable fields

N/A

Severity level

6

Example

ARP/6/ARP_DYNAMIC: The maximum number of dynamic ARP entries for the device reached.

Explanation

The maximum number of dynamic ARP entries for the device was reached.

Recommended action

No action is required.

 

ARP_DYNAMIC_IF

Message text

The maximum number of dynamic ARP entries for interface [STRING] reached.

Variable fields

$1: Interface name.

Severity level

6

Example

ARP/6/ARP_DYNAMIC_IF: The maximum number of dynamic ARP entries for interface GigabitEthernet1/0/1 reached.

Explanation

The maximum number of dynamic ARP entries for the specified interface was reached.

Recommended action

No action is required.

 

ARP_DYNAMIC_SLOT

Message text

The maximum number of dynamic ARP entries for slot [UINT32] reached.

Variable fields

$1: Member device ID.

Severity level

6

Example

ARP/6/ARP_DYNAMIC_SLOT: The maximum number of dynamic ARP entries for slot 2 reached.

ARP/6/ARP_DYNAMIC_SLOT: The maximum number of dynamic ARP entries for chassis 1 slot 2 reached.

Explanation

The maximum number of dynamic ARP entries for the member device was reached.

Recommended action

No action is required.

 

ARP_ENTRY_CONFLICT

Message text

The software entry for [STRING] on [STRING] and the hardware entry did not have the same [STRING].

Variable fields

$1: IP address.

$2: VPN instance name. If the ARP entry belongs to the public network, this field displays the public network.

$3: Inconsistent items:

?     MAC address.

?     output interface.

?     output port.

?     outermost layer VLAN ID.

?     second outermost layer VLAN ID.

?     VSI index.

?     link ID.

Severity level

6

Example

ARP/6/ARP_ENTRY_CONFLICT: The software entry for 1.1.1.1 on the VPN a and the hardware entry did not have the same MAC address, output port, VSI index, and link ID.

ARP/6/ARP_ENTRY_CONFLICT: The software entry for 1.1.1.2 on the public  network and the hardware entry did not have the same MAC address, output port, VSI index, and link ID.

Explanation

The software entry for the specified IP address is not the same as the hardware entry. For example, they do not have the same output interface.

Recommended action

No action is required. ARP automatically refreshes the hardware entries.

 

ARP_HOST_IP_CONFLICT

Message text

The host [STRING] connected to interface [STRING] cannot communicate correctly, because it uses the same IP address as the host connected to interface [STRING].

Variable fields

$1: IP address.

$2: Interface name.

$3: Interface name.

Severity level

4

Example

ARP/4/ARP_HOST_IP_CONFLICT: The host 1.1.1.1 connected to interface GigabitEthernet1/0/1 cannot communicate correctly, because it uses the same IP address as the host connected to interface GigabitEthernet1/0/2.

Explanation

The sender IP address in a received ARP message conflicted with the IP address of a host connected to another interface.

Recommended action

Check whether the hosts that send the ARP messages are legitimate. Disconnect the illegal host from the network.

 

ARP_LOCALPROXY_ENABLE_FAILED

Message text

Failed to enable local proxy ARP on interface [STRING].

Variable fields

$1: Interface name.

Severity level

4

Example

ARP/4/ARP_LOCALPROXY_ENABLE_FAILED: -MDC=1-Slot=2; Failed to enable local proxy ARP on interface VSI-interface 1.

Explanation

This message is sent when the device fails to enable local proxy ARP on an interface in a slot. If the interface resides on the MPU, the slot number is 0.

Recommended action

1.     Verify that the card supports local proxy ARP.

2.     Verify that sufficient hardware resources are available.

 

ARP_RATE_EXCEEDED

Message text

The ARP packet rate ([UINT32] pps) exceeded the rate limit ([UINT32] pps) on interface [STRING] in the last [UINT32] seconds.

Variable fields

$1: ARP packet rate.

$2: ARP limit rate.

$3: Interface name.

$4: Interval time.

Severity level

4

Example

ARP/4/ARP_RATE_EXCEEDED: The ARP packet rate (100 pps) exceeded the rate limit (80 pps) on interface GigabitEthernet1/0/1 in the last 10 seconds.

Explanation

An interface received ARP messages at a higher rate than the rate limit.

Recommended action

Verify that the hosts at the sender IP addresses are legitimate.

 

ARP_RATELIMIT_NOTSUPPORT

Message text

 ARP packet rate limit is not support on slot [UINT32].

Variable fields

$1: Member device ID.

Severity level

6

Example

ARP/6/ARP_RATELIMIT_NOTSUPPORT: ARP packet rate limit is not support on slot 2.

Explanation

ARP packet rate limit is not supported on the member device.

Recommended action

Verify that the host at the sender IP address is legitimate.

 

ARP_SENDER_IP_INVALID

Message text

Sender IP [STRING] was not on the same network as the receiving interface [STRING].

Variable fields

$1: IP address.

$2: Interface name.

Severity level

6

Example

ARP/6/ARP_SENDER_IP_INVALID: Sender IP 192.168.10.2 was not on the same network as the receiving interface GigabitEthernet1/0/1.

Explanation

The sender IP of a received ARP message was not on the same network as the receiving interface.

Recommended action

Verify that the host at the sender IP address is legitimate.

 

ARP_SENDER_MAC_INVALID

Message text

Sender MAC [STRING] was not identical to Ethernet source MAC [STRING] on interface [STRING].

Variable fields

$1: MAC address.

$2: MAC address.

$3: Interface name.

Severity level

6

Example

ARP/6/ARP_SENDER_MAC_INVALID: Sender MAC 0000-5E14-0E00 was not identical to Ethernet source MAC 0000-5C14-0E00 on interface GigabitEthernet1/0/1.

Explanation

An interface received an ARP message. The sender MAC address in the message body was not identical to the source MAC address in the Ethernet header.

Recommended action

Verify that the host at the sender MAC address is legitimate.

 

ARP_SENDER_SMACCONFLICT

Message text

Packet was discarded because its sender MAC address was the MAC address of the receiving interface.

Interface: [STRING], sender IP: [STRING], target IP: [STRING].

Variable fields

$1: Interface name.

$2: Sender IP address.

$3: Target IP address.

Severity level

6

Example

ARP/6/ ARP_SENDER_SMACCONFLICT: Packet discarded for the sender MAC address is the same as the receiving interface.

Interface: GigabitEthernet1/0/1 sender IP: 1.1.2.2 target IP: 1.1.2.1,

Explanation

The sender MAC address of a received ARP packet conflicts with the MAC address of the device.

Recommended action

No action is required.

 

ARP_SENDER_SMACCONFLICT_VSI

Message text

Packet was discarded because its sender MAC address was the MAC address of the receiving interface.

Interface: [STRING], sender IP: [STRING], target IP: [STRING],VSI index: [UINT32], link ID: [UINT32].

Variable fields

$1: Interface name.

$2: Sender IP address.

$3: Target IP address.

$4: VSI index.

$5: Link ID.

Severity level

6

Example

ARP/6/ ARP_SENDER_SMACCONFLICT_VSI: Packet discarded for the sender MAC address is the same as the receiving interface.

Interface: VSI3 sender IP: 1.1.2.2 target IP: 1.1.2.1, VSI Index: 2, Link ID: 0

Explanation

The sender MAC address of a received ARP packet conflicts with the MAC address of the device. The receiving interface is a VSI interface.

Recommended action

No action is required.

 

ARP_SRC_MAC_FOUND_ATTACK

Message text

An attack from MAC [STRING] was detected on interface [STRING].

Variable fields

$1: MAC address.

$2: Interface name.

Severity level

6

Example

ARP/6/ARP_SRC_MAC_FOUND_ATTACK: An attack from MAC 0000-5E14-0E00 was detected on interface GigabitEthernet1/0/1.

Explanation

The source MAC-based ARP attack detection feature received more ARP packets from the same MAC address within 5 seconds than the specified threshold.

This message indicates the risk of attacks.

Recommended action

Verify that the host at the source MAC address is legitimate.

 

ARP_SUP_ENABLE_FAILED

Message text

Failed to enable ARP flood suppression on VSI [STRING].

Variable fields

$1: VSI name.

Severity level

4

Example

ARP/4/ARP_SUP_ENABLE_FAILED: -MDC=1; Failed to enable ARP flood suppression on VSI vpna.

Explanation

This message is sent when the system failed to enable ARP flood suppression for a VSI. The minimum interval between two log messages is 2 seconds. To make the system send the message successfully, wait for a minimum of 2 seconds before you enable ARP flood suppression for another VSI.

Recommended action

1.     Verify that the device supports ARP flood suppression.

2.     Verify that the hardware resources are sufficient.

 

ARP_TARGET_IP_INVALID

Message text

Target IP [STRING] was not the IP of the receiving interface [STRING].

Variable fields

$1: IP address.

$2: Interface name.

Severity level

6

Example

ARP/6/ARP_TARGET_IP_INVALID: Target IP 192.168.10.2 was not the IP of the receiving interface GigabitEthernet1/0/1.

Explanation

The target IP address of a received ARP message was not the IP address of the receiving interface.

Recommended action

Verify that the host at the sender IP address is legitimate.

 

ARP_THRESHOLD_REACHED

Message text

The alarm threshold for dynamic ARP entry learning was reached on interface [STRING].

Variable fields

$1: Interface name.

Severity level

4

Example

ARP/4/ARP_THRESHOLD_REACHED: The alarm threshold for dynamic ARP entry learning was reached on interface GigabitEthernet1/0/1.

Explanation

This message is sent when the alarm threshold for dynamic ARP learning was reached on GigabitEthernet 1/0/1.

Recommended action

Verify that the number of learned dynamic ARP entries matches the actual number of devices in the network and no ARP attack sources exist in the network.

 

DUPIFIP

Message text

Duplicate address [STRING] on interface [STRING], sourced from [STRING].

Variable fields

$1: IP address.

$2: Interface name.

$3: MAC Address.

Severity level

6

Example

ARP/6/DUPIFIP: Duplicate address 1.1.1.1 on interface GigabitEthernet1/0/1, sourced from 0015-E944-A947.

Explanation

ARP detected a duplicate address.

The sender IP in the received ARP packet was being used by the receiving interface.

Recommended action

Modify the IP address configuration.

 

DUPIP

Message text

IP address [STRING] conflicted with global or imported IP address, sourced from [STRING].

Variable fields

$1: IP address.

$2: MAC Address.

Severity level

6

Example

ARP/6/DUPIP: IP address 30.1.1.1 conflicted with global or imported IP address, sourced from 0000-0000-0001.

Explanation

The sender IP address of the received ARP packet conflicted with the global or imported IP address.

Recommended action

Modify the IP address configuration.

 

DUPVRRPIP

Message text

IP address [STRING] conflicted with VRRP virtual IP address on interface [STRING], sourced from [STRING].

Variable fields

$1: IP address.

$2: Interface name.

$3: MAC address.

Severity level

6

Example

ARP/6/DUPVRRPIP: IP address 1.1.1.1 conflicted with VRRP virtual IP address on interface GigabitEthernet1/0/1, sourced from 0015-E944-A947.

Explanation

The sender IP address of the received ARP packet conflicted with the VRRP virtual IP address.

Recommended action

Modify the IP address configuration.

 

 


ATK messages

This section contains attack detection and prevention messages.

ATK_ICMP_ADDRMASK_REQ

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_REQ: IcmpType(1058)=17; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP address mask request logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_ADDRMASK_REQ_RAW

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_REQ_RAW: IcmpType(1058)=17; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP address mask requests of the same attributes, this message is sent only when the first request is received.

If log aggregation is disabled, this message is sent every time an ICMP address mask request is received.

Recommended action

No action is required.

 

ATK_ICMP_ADDRMASK_REQ_RAW_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_REQ_RAW_SZ: IcmpType(1058)=17; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP address mask requests of the same attributes, this message is sent only when the first request is received.

If log aggregation is disabled, this message is sent every time an ICMP address mask request is received.

Recommended action

No action is required.

 

ATK_ICMP_ADDRMASK_REQ_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_REQ_SZ: IcmpType(1058)=17; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP address mask request logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_ADDRMASK_RPL

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_RPL: IcmpType(1058)=18; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP address mask reply logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_ADDRMASK_RPL_RAW

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_RPL_RAW: IcmpType(1058)=18; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP address mask replies of the same attributes, this message is sent only when the first reply is received.

If log aggregation is disabled, this message is sent every time an ICMP address mask reply is received.

Recommended action

No action is required.

 

ATK_ICMP_ADDRMASK_RPL_RAW_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_RPL_RAW_SZ: IcmpType(1058)=18; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP address mask replies of the same attributes, this message is sent only when the first reply is received.

If log aggregation is disabled, this message is sent every time an ICMP address mask reply is received.

Recommended action

No action is required.

 

ATK_ICMP_ADDRMASK_RPL_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_RPL_SZ: IcmpType(1058)=18; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP address mask reply logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_ECHO_REQ

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_ECHO_REQ: IcmpType(1058)=8; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP echo request logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_ECHO_REQ_RAW

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; DstPort(1004)=[UINT16]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Destination port number.

$7: Name of the receiving VPN instance.

$8: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_ECHO_REQ_RAW: IcmpType(1058)=8; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DstPort(1004)=22; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP echo requests of the same attributes, this message is sent only when the first request is received.

If log aggregation is disabled, this message is sent every time an ICMP echo request is received.

Recommended action

No action is required.

 

ATK_ICMP_ECHO_REQ_RAW_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; DstPort(1004)=[UINT16]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Destination port number.

$7: Name of the receiving VPN instance.

$8: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_ECHO_REQ_RAW_SZ: IcmpType(1058)=8; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DstPort(1004)=22; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP echo requests of the same attributes, this message is sent only when the first request is received.

If log aggregation is disabled, this message is sent every time an ICMP echo request is received.

Recommended action

No action is required.

 

ATK_ICMP_ECHO_REQ_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_ECHO_REQ_SZ: IcmpType(1058)=8; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP echo request logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_ECHO_RPL

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_ECHO_RPL: IcmpType(1058)=0; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP echo reply logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_ECHO_RPL_RAW

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_ECHO_RPL_RAW: IcmpType(1058)=0; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP echo replies of the same attributes, this message is sent only when the first reply is received.

If log aggregation is disabled, this message is sent every time an ICMP echo reply is received.

Recommended action

No action is required.

 

ATK_ICMP_ECHO_RPL_RAW_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_ECHO_RPL_RAW_SZ: IcmpType(1058)=0; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP echo replies of the same attributes, this message is sent only when the first reply is received.

If log aggregation is disabled, this message is sent every time an ICMP echo reply is received.

Recommended action

No action is required.

 

ATK_ICMP_ECHO_RPL_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_ECHO_RPL_SZ: IcmpType(1058)=0; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP echo reply logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_FLOOD

Message text

RcvIfName(1023)=[STRING]; DstIPAddr(1007)=[IPADDR]; DstPort(1008)=[UINT16]; RcvVPNInstance(1041)=[STRING]; UpperLimit(1048)=[UINT32]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING].

Variable fields

$1: Receiving interface name.

$2: Destination IP address.

$3: Destination port number.

$4: Name of the receiving VPN instance.

$5: Rate limit.

$6: Actions against the attack.

$7: Start time of the attack.

Severity level

3

Example

ATK/3/ATK_ICMP_FLOOD: RcvIfName(1023)=Ethernet0/0/2; DstIPAddr(1007)=6.1.1.5; DstPort(1008)=22; RcvVPNInstance(1041)=--; UpperLimit(1048)=10; Action(1049)=logging; BeginTime_c(1011)=20131009093351.

Explanation

This message is sent when the number of ICMP packets sent to a destination per second exceeds the rate limit.

Recommended action

No action is required.

 

ATK_ICMP_FLOOD_SZ

Message text

SrcZoneName(1025)=[STRING]; DstIPAddr(1007)=[IPADDR]; DstPort(1008)=[UINT16]; RcvVPNInstance(1041)=[STRING]; UpperLimit(1048)=[UINT32]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING].

Variable fields

$1: Source security zone name.

$2: Destination IP address.

$3: Destination port number.

$4: Name of the receiving VPN instance.

$5: Rate limit.

$6: Actions against the attack.

$7: Start time of the attack.

Severity level

3

Example

ATK/3/ATK_ICMP_FLOOD_SZ: SrcZoneName(1025)=Trust; DstIPAddr(1007)=6.1.1.5; DstPort(1008)=22; RcvVPNInstance(1041)=--; UpperLimit(1048)=10; Action(1049)=logging; BeginTime_c(1011)=20131009093351.

Explanation

This message is sent when the number of ICMP packets sent to a destination per second exceeds the rate limit.

Recommended action

No action is required.

 

ATK_ICMP_INFO_REQ

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_INFO_REQ: IcmpType(1058)=15; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP information request logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_INFO_REQ_RAW

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_INFO_REQ_RAW: IcmpType(1058)=15; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP information requests of the same attributes, this message is sent only when the first request is received.

If log aggregation is disabled, this message is sent every time an ICMP information request is received.

Recommended action

No action is required.

 

ATK_ICMP_INFO_REQ_RAW_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_INFO_REQ_RAW_SZ: IcmpType(1058)=15; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP information requests of the same attributes, this message is sent only when the first request is received.

If log aggregation is disabled, this message is sent every time an ICMP information request is received.

Recommended action

No action is required.

 

ATK_ICMP_INFO_REQ_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_INFO_REQ_SZ: IcmpType(1058)=15; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP information request logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_INFO_RPL

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_INFO_RPL: IcmpType(1058)=16; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP information reply logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_INFO_RPL_RAW

Message text

IcmpType(1058)=[UINT32]; RcvIfName(