Contents

Configuring cloud connections· 1

About cloud connections· 1

Multiple subconnections· 1

Cloud connection establishment 1

Configuring a cloud connection· 2

Unbinding the device from the Oasis server 3

Display and maintenance commands for cloud connections· 3

Cloud connection configuration examples· 3

Example: Configuring a cloud connection· 3

Configuring cloud connections

About cloud connections

A cloud connection is a management tunnel established between a local device and the H3C cloud server. It enables you to manage the local device from the cloud server without accessing the network where the device resides.

Multiple subconnections

After a local device establishes a connection with the cloud server, service modules on the local device can establish multiple subconnections with the microservices on the cloud server. These subconnections are independent from each other and provide separate communication channels for different services. This mechanism avoids interference among different services.

Cloud connection establishment

The cloud connection is established as follows:

1.     The device sends an authentication request to the cloud server.

2.     The cloud server sends an authentication success packet to the device.

The device passes the authentication only if the serial number of the device has been added to the cloud server. If the authentication fails, the cloud server sends an authentication failure packet to the device.

3.     The device sends a registration request to the cloud server.

4.     The cloud server sends a registration response to the device.

The registration response contains the uniform resource locator (URL) used to establish a cloud connection.

5.     The device uses the URL to send a handshake request (changing the protocol from HTTP to WebSocket) to the cloud server.

6.     The cloud server sends a handshake response to the device to finish establishing the cloud connection.

7.     The device sends a subconnection URL request to the cloud server.

8.     The cloud server sends a response that contains the microservice list and all subconnection URLs to the device.

9.     The service module registers on the cloud connection management module.

10.     The cloud connection management module sends the corresponding URLs to the service module.

11.     The service module establishes subconnections with the cloud server.

Figure 1 Establishing a cloud connection

Configuring a cloud connection

About configuring a cloud connection

For a successful cloud connection establishment, specify the domain name of the cloud server and map the IP address of the cloud server to the domain name.

After establishing the cloud connection, the local device sends keepalive packets to the cloud server periodically. If the device does not receive a response from the cloud server within three keepalive intervals, the device sends a registration request to re-establish the cloud connection.

Prerequisites

Add the serial number of the device to be managed to the cloud server.

Configure DNS to ensure that the domain name of the cloud server can be translated into an IP address.

Procedure

1.     Enter system view.

system-view

2.     Configure the domain name of the cloud server.

cloud-management server domain domain-name

By default, the domain name of the cloud server is not configured.

3.     (Optional) Set the keepalive interval.

cloud-management keepalive interval

By default, the keepalive interval is 180 seconds.

4.     (Optional) Specify the TCP port number used to establish cloud connections.

cloud-management server port port-number

By default, the TCP port number used to establish cloud connections is 443.

Unbinding the device from the Oasis server

About this task

A device can be registered on the Oasis server by only one user.

To register a device that has been registered by another user, you need to take the following steps:

1.     Obtain a verification code for device unbinding from the Oasis server.

2.     Execute the command on the device for sending the verification code to the Oasis server.

3.     Register the device on the Oasis server.

Restrictions and guidelines

Only Release 6320 and later versions support this feature.

Procedure

1.     Enter system view.

system-view

2.     Send the verification code for device unbinding to the Oasis server.

cloud-management unbinding-code code

Display and maintenance commands for cloud connections

Execute display commands in any view and reset commands in user view.

Cloud connection configuration examples

Example: Configuring a cloud connection

Network configuration

As shown in Figure 2, configure the device to establish a cloud connection with the cloud server.

Figure 2 Network diagram

Procedure

1.     Configure IP addresses for interfaces, and configure a routing protocol to ensure that the devices can reach each other. (Details not shown.)

2.     Log in to the cloud server to add the serial number of the device to the server. (Details not shown.)

The IP address of the cloud server is 10.1.1.1/24 and the domain name is cloud.com.

3.     Configure the domain name of the cloud server as cloud.com.

<Device> system-view

[Device] cloud-management server domain cloud.com

# Map IP address 10.1.1.1 to host name cloud.com.

[Device] ip host cloud.com 10.1.1.1

Verifying the configuration

# Verify that the device and the cloud server have established a cloud connection.

[Device] display cloud-management state

Cloud connection state   : Established

Device state             : Request_success

Cloud server address     : 10.1.1.1

Cloud server domain name : cloud.com

Cloud server port        : 443

Connected at             : Wed Jan  27 14:18:40 2016

Duration                 : 00d 00h 02m 01s