Title | Size | Downloads |
---|---|---|
H3C LSQ1AFCBSC0 Card Manual(V1.01)-book.pdf | 47.04 KB |
- Table of Contents
2 x 10/100/1000BASE-T Electrical Interface + 2 x Gigabit Combo Interface Anomaly Flow Cleaner Card –LSQ1AFCBSC0
1 Card Identifier
The silkscreen LSQ1AFCBSC0 is printed at the upper right corner of the front panel to identify the card.
2 Specifications
The LSQ1AFCBSC0 card provides one console port, one CF card interface, two USB interfaces, two 10/100/1000BASE-T Ethernet copper interfaces, and two Gigabit Combo interfaces.
Table1 LSQ1AFCBSC0 specifications
Item |
Specifications |
Interface |
1 Console port |
1 CF card interface, supporting 256MB, 512MB and 1GB CF cards |
|
2 USB interfaces |
|
2 10/100/1000BASE-T electrical interfaces |
|
2 Gigabit Combo interfaces, supporting flexible switching between optical and electric interfaces. Only one type of interface(s), optical or electrical, can work at a time. Supported interface types are as follows: l 10/100/1000BASE-T electrical interface l 1000BASE-X SFP optical interface |
|
Interface transmission speed |
l Console port: 9600 bps to 115200 bps (default: 9600 bps) l 10/100/1000BASE-T electrical interface: 10/100/1000 Mbps, half/full duplex l 1000BASE-X SFP optical interface: 10000 Mbps. Full duplex |
Connector |
RJ-45 (for electrical interface) or SFP/LC (for optical interface) |
Cable and maximum transmission distance |
l Console port: Asynchronous serial cable with maximum transmission distance of 15 meters l 10/100/1000BASE-T electrical interface: Category 5 or above UTP with maximum transmission distance of 100 meters l 1000BASE-X SFP optical interface: Refer to Table2 for details |
Applied to |
S7500E Series Ethernet switches |
Table2 1000BASE-X SFP interface specifications
Item |
Specifications |
|||||
Connector |
SFP/LC |
|||||
Interface standards |
802.3, 802.3u and 802.3ab |
|||||
Optical transmit power |
Type |
Short-haul multi-mode (850 nm) Optical interface module |
Mid-haul single-mode (1310 nm) Optical interface module |
Long-haul (1310 nm) Optical interface module |
Long-haul (1550 nm) Optical interface module |
Extra-long-haul (1550 nm) Optical interface module |
Min. |
-9.5 dBm |
-9 dBm |
-2 dBm |
-4 dBm |
-4 dBm |
|
Max. |
0 dBm |
-3 dBm |
5 dBm |
1 dBm |
2 dBm |
|
Reception sensitivity |
-17dBm |
-20 dBm |
-23 dBm |
-21 dBm |
-22 dBm |
|
Central wavelength |
850 nm |
1310 nm |
1310 nm |
1550 nm |
1550 nm |
|
Fiber type |
62.5/125µm MM fiber |
9/125µm SM fiber |
9/125µm SM fiber |
9/125µm SM fiber |
9/125µm SM fiber |
|
Max transmission distance |
0.55 km |
10 km |
40 km |
40 km |
70 km |
3 Software Upgrade
The LSQ1AFCBSC0 card supports software upgrade through the console port or an Ethernet interface on the card. For details, refer to H3C SecBlade Card Software Upgrade Manual.
The LSQ1AFCBSC0 card does not support software upgrade through the SRPU of the S7500E switch.
4 Note
If the host software version does not match the one applicable to the card, contact the local dealer or the integrator for the right version.
For the introduction to card installation and host software upgrade, see the related Installation Manual.
As board types or specifications might change with product versions, you may need to obtain the latest documents from Technical Support & Document link on H3C website http://www.h3c.com
Note: This card manual written in English is applicable for the territories except the mainland China (excluding Hong Kong, Macao and ).
Copyright © 2007-2010 Hangzhou H3C Technologies Co., Ltd.