02-WLAN

HomeSupportResource CenterH3C Access Controllers Command References(E5208P03 E5215P01 R5215P01)-6W10202-WLAN
16-Hotspot 2.0 commands
Title Size Download
16-Hotspot 2.0 commands 156.68 KB

Hotspot 2.0 commands

3gpp-info

Use 3gpp-info to configure 3GPP information.

Use undo 3gpp-info to remove 3GPP information.

Syntax

3gpp-info country-code mobile-country-code network-code mobile-network-code

undo 3gpp-info country-code mobile-country-code network-code mobile-network-code

Default

No 3GPP information is configured.

Views

Hotspot 2.0 policy view

Predefined user roles

network-admin

Parameters

mobile-country-code: Specifies a mobile country code (MCC). An MCC is a three-digit numeric code that uniquely identifies the country to which clients belong.

mobile-network-cod: Specifies a mobile network code (MNC). A mobile network code is a two-digit or three-digit numeric code that uniquely identifies the mobile network to which clients belong.

Usage guidelines

You can specify a maximum of 32 country code and mobile network code combinations in a Hotspot 2.0 policy.

One country code can be combined with multiple mobile network codes.

Examples

# Configure 3GPP information: set the country code to 460 and network code to 01.

<Sysname> system-view

[Sysname] wlan hotspot-policy 1

[Sysname-wlan-hs-1] 3gpp-info country-code 460 network-code 01

authentication-type

Use authentication-type to specify a network authentication type.

Use undo authentication-type to delete a network authentication type.

Syntax

authentication-type { 0 [ redirect-url url ] | 1 | 2 redirect-url url | 3 }

undo authentication-type { 0 | 1 | 2 | 3 }

Default

No network authentication type is specified.

Views

Hotspot 2.0 policy view

Predefined user roles

network-admin

Parameters

0: Specifies acceptance of terms and conditions.

1: Specifies on-line enrollment.

2: Specifies HTTP/HTTPS redirection.

3: Specifies DNS redirection.

redirect-url url: Specifies a redirected URL address.

Usage guidelines

You can specify a maximum of four network authentication types in a Hotspot 2.0 policy.

Examples

# Specify a network authentication type.

<Sysname> system-view

[Sysname] wlan hotspot-policy 1

[Sysname-wlan-hs-1] authentication-type 1

comeback-delay

Use comeback-delay to set the comeback delay for clients to send GAS comeback requests.

Use undo comeback-delay to restore the default.

Syntax

comeback-delay value

undo comeback-delay

Default

The comeback delay is 1 TU.

Views

Hotspot 2.0 policy view

Predefined user roles

network-admin

Parameters

value: Specifies the comeback delay in the range of 1 to 1024 TUs. One TU is equal to 1024 μs.

Usage guidelines

This command can prevent clients from sending too many GAS comeback requests.

Examples

# Set the comeback delay to 10 TUs.

<Sysname> system-view

[Sysname] wlan hotspot-policy 1

[Sysname-wlan-hs-1] comeback-delay 10d

description

Use description to configure a description for an OSU server.

Use undo description to delete an OSU server description.

Syntax

description description lang-code lang-code

undo description description lang-code lang-code

Default

No description is configured for an OSU server.

Views

OSU server view

Predefined user roles

network-admin

Parameters

description: Specifies a description, a case-sensitive string of 1 to 252 characters.

lang-code: Specifies a language code. The device supports the general international standards.

Usage guidelines

This command is available only for version 2 of Hotspot 2.0.

You can configure a maximum of 32 descriptions for an OSU server. A client displays one description that is in the same language as the client system.

Examples

# Configure a description for OSU server 1.

<Sysname> system-view

[Sysname] wlan osu-provider 1

[Sysname-wlan-osu-1] description "Free service for test purpose" lang-code eng

dgaf enable

Use dgaf enable to enable Downstream Group-Addressed Forwarding (DGAF).

Use undo dgaf enable to disable DGAF.

Syntax

dgaf enable

undo dgaf enable

Default

DGAF is enabled.

Views

Hotspot 2.0 policy view

Predefined user roles

network-admin

Usage guidelines

Before disabling DGAF, make sure all service templates bound to the Hotspot 2.0 policy are disabled.

DGAF enables an AP to forward all downstream wireless broadcast ARP packets and wireless multicast packets. To prevent spoofing attacks by using downstream multicasts, you can disable DGAF for the AP.

To avoid packet loss, enable proxy ARP and multicast optimization before disabling DGAF. For more information about proxy ARP, see Layer 3—IP Services Configuration Guide.

Examples

# Disable DGAF.

<Sysname> system-view

[Sysname] wlan hotspot-policy 1

[Sysname-wlan-hs-1] undo dgaf enable

display wlan hotspot uploaded-osu-icon

Use display wlan hotspot uploaded-osu-icon to display the list of uploaded OSU server icons.

Syntax

display wlan hotspot uploaded-osu-icon

Views

Any view

Predefined user roles

network-admin

Usage guidelines

This command is available only for version 2 of Hotspot 2.0.

Examples

# Display the list of uploaded OSU server icons.

<Sysname> display wlan hotspot uploaded-osu-icon

Total uploaded osu icon count: 1

Icon name                                 Icon type

---------------------------------------------------------

college.png                                  png

Related commands

icon-file

wlan hotspot osu-icon upload

domain-name

Use domain-name to set an ISP domain name.

Use undo domain-name to delete an ISP domain name.

Syntax

domain-name domain-name

undo domain-name domain-name

Default

No domain name is set.

Views

Hotspot 2.0 policy view

Predefined user roles

network-admin

Parameters

domain-name: Specifies a domain by its name, a case-sensitive string of 1 to 255 characters.

Usage guidelines

You can configure a maximum of 32 domain names in one Hotspot 2.0 policy.

Examples

# Set the domain name to college in Hotspot 2.0 policy 1.

<Sysname> system-view

[Sysname] wlan hotspot-policy 1

[Sysname-wlan-hs-1] domain-name college

gas-limit

Use gas-limit to set the maximum number of GAS initial requests that the AC can receive within the specified interval.

Use undo gas-limit to restore the default.

Syntax

gas-limit number number interval interval

undo gas-limit

Default

The number of GAS initial requests that the AC can receive is not limited.

Views

Hotspot 2.0 policy view

Predefined user roles

network-admin

Parameters

number number: Specifies the maximum number of GAS initial requests that the AC can receive, in the range of 10 to 60.

interval interval: Specifies the interval at which the AC receive GAS initial requests, in the range of 10 to 60 seconds.

Usage guidelines

This feature enables you to limit the number of GAS initial requests that the AC can receive within the specified interval to release the burden of the AC.

If the number of GAS initial requests received by the AC exceeds the limit, the exceeded frames will be discarded.

Examples

# Set the maximum number of GAS initial requests that the AC can receive within 15 seconds to 50.

<Sysname> system-view

[Sysname] wlan hotspot-policy 1

[Sysname-wlan-hs-1] gas-limit number 50 interval 15

hessid

Use hessid to set a homogenous ESS identifier (HESSID).

Use undo hessid to restore the default.

Syntax

hessid hessid

undo hessid

Default

No HESSID is set.

Views

Hotspot 2.0 policy view

Predefined user roles

network-admin

Parameters

hessid: Specifies an HESSID that uniquely identifies a homogeneous ESS, in the H-H-H format. The value cannot be all zeros.

Usage guidelines

Make sure all service templates bound to the Hotspot 2.0 policy are disabled before you set an HESSID.

Examples

# Set the HESSID to 0021-1bea-3660 in Hotspot 2.0 policy 1.

<Sysname> system-view

[Sysname] wlan hotspot-policy 1

[Sysname-wlan-hs-1] hessid 0021-1bea-3660

hotspot-policy

Use hotspot-policy to bind a Hotspot 2.0 policy to a service template.

Use undo hotspot-policy to restore the default.

Syntax

hotspot-policy policy-number

undo hotspot-policy

Default

No Hotspot 2.0 policy is bound to a service template.

Views

Service template view

Predefined user roles

network-admin

Parameters

policy-number: Specifies the number of a Hotspot 2.0 policy, in the range of 1 to 32.

Usage guidelines

Before you bind a Hotspot 2.0 policy to a service template, perform the following tasks:

·     Make sure the Hotspot 2.0 policy exists and the service template is disabled.

·     Make sure the following settings are configured for the service template:

¡     802.1X authentication and key management mode.

¡     RSN IE.

¡     AES-CCMP cipher suite.

Examples

# Bind Hotspot 2.0 policy 1 to service template 1.

<Sysname> system-view

[Sysname] wlan service-template 1

[Sysname-wlan-st-1] hotspot-policy 1

icon-file

Use icon-file to specify an icon for an OSU server.

Use undo icon-file to delete the specified icon for an OSU server.

Syntax

icon-file filename lang-code lang-code icon-type icon-type

undo icon-file filename

Default

No icon is specified for an OSU server.

Views

OSU server view

Predefined user roles

network-admin

Parameters

filename: Specifies an icon file by its name, a case-sensitive string of 1 to 63 characters.

lang-code lang-code: Specifies a language code. The device supports the general international standards.

icon-type icon-type: Specifies the type of the icon file, a case-sensitive string of 1 to 15 characters.

Usage guidelines

This command is available only for version 2 of Hotspot 2.0.

The device loads the specified icon when the command is executed. You can specify a maximum of six icons for an OSU server. A client displays an icon that is in the same language as the client system.

When you specify an icon for an OSU server, follow these restrictions and guidelines:

·     Create a directory named icon in the root directory where the version files are saved, and use FTP or TFTP to download icon files to the folder before executing the command.

·     If the specified icon file does not exist in the icon directory, the command cannot load the icon file. To load the icon file, save the icon file in the icon directory, and then execute the wlan hotspot osu-icon upload command.

·     The file size cannot exceed 64 KB.

·     Make sure the file type specified in the command is the same as the actual file type.

·     If  an OSU server is already bound to a Hotspot 2.0 policy, you cannot delete the most recently specified OSU server icon.

Examples

# Specify an icon for OSU server 1.

<Sysname> system-view

[Sysname] wlan osu-provider 1

[Sysname-wlan-osu-1] icon-file wifi_icon lang-code eng icon-type png

ip-protocol

Use ip-protocol to set the port status for an IP protocol.

Use undo ip-protocol to remove the configuration.

Syntax

ip-protocol { esp | icmp | tcp | udp } port-number port-number { closed | open | unknown }

undo ip-protocol { esp | icmp | tcp | udp } port-number port-number

Default

The port status is not configured for an IP protocol.

Views

Hotspot 2.0 policy view

Predefined user roles

network-admin

Parameters

esp: Specifies the ESP protocol.

icmp: Specifies the ICMP protocol.

tcp: Specifies the TCP protocol.

udp: Specifies the UDP protocol.

port-number: Specifies a port by its number.

Table 1 Port number and protocol type

Protocol type

Port number

Description

ICMP

0

ICMP, used for diagnostics

TCP

20

FTP

TCP

22

SSH

TCP

80

HTTP

TCP

443

Used by TLS VPNs

TCP

1723

Used by Point to Point

Tunneling Protocol VPNs

TCP

5060

VoIP

UDP

500

Used by IKEv2 (IPSec VPN)

UDP

5060

VoIP

UDP

4500

May be used by IKEv2 (IPSec VPN)

ESP

0

ESP, used by IPSec VPNs

 

closed: Specifies the port status as closed.

open: Specifies the port status as open.

unknown: Specifies the port status as unknown.

Examples

# Set the port number to 20 and the port status to open for TCP.

<Sysname> system-view

[Sysname] wlan hotspot-policy 1

[Sysname-wlan-hs-1] ip-protocol tcp port-number 20 open

ip-type

Use ip-type to configure IP address availability.

Use undo ip-type to restore the default.

Syntax

ip-type ipv4 ipv4-type ipv6 ipv6-type

undo ip-type

Default

The availability is 1 for IPv4 addresses and 2 for IPv6 addresses.

Views

Hotspot 2.0 policy view

Predefined user roles

network-admin

Parameters

ipv4-type: Specifies the availability for an IPv4 address, in the range of 0 to 7.

Table 2 IPv4 address availability

Address value

Description

0

Address type not available

1

Public IPv4 address available

2

Port-restricted IPv4 address available

3

Single NATed private IPv4 address available

4

Double NATed private IPv4 address available

5

Port-restricted IPv4 address and single NATed IPv4 address available

6

Port-restricted IPv4 address and double NATed IPv4 address available

7

Availability of the address type is not known

 

ipv6-type: Specifies the availability for an IPv6 address, in the range of 0 to 2.

Table 3 IPv6 address availability

Address value

Description

0

Address type not available

1

Address type available

2

Availability of the address type not known

 

Examples

# Set the availability to 2 for IPv4 addresses and 1 for IPv6 addresses.

<Sysname> system-view

[Sysname] wlan hotspot-policy 1

[Sysname-wlan-hs-1] ip-type ipv4 2 ipv6 1

method

Use method to specify a protocol for clients to communicate with the OSU server.

Use undo method to delete the specified protocol for clients to communicate with the OSU server.

Syntax

method method-id

undo method method-id

Default

No protocol is specified for clients to communicate with an OSU server.

Views

OSU server view

Predefined user roles

network-admin

Parameters

method-id: Specifies the protocol ID:

·     0—Specifies OMA-DM.

·     1—Specifies SOAP-XML SPP.

Usage guidelines

This command is available only for version 2 of Hotspot 2.0.

You can specify both protocols. Clients will choose one protocol to communicate with the OSU server.

If an OSU server is already bound to a Hotspot 2.0 policy, you cannot delete the most recent specified protocol for clients to communicate with the OSU server.

Examples

# Specify a protocol for clients to communicate with the OSU server.

<Sysname> system-view

[Sysname] wlan osu-provider 1

[Sysname-wlan-osu-1] method 0

nai

Use nai to configure a Network Access Identifier (NAI) for an OSU server.

Use undo nai to delete the configured NAI for an OSU server.

Syntax

nai nai

undo nai

Default

No NAI is configured for an OSU server.

Views

OSU server view

Predefined user roles

network-admin

Parameters

nai: Specifies an NAI, a case-sensitive string of 1 to 252 characters.

Usage guidelines

This command is available only for version 2 of Hotspot 2.0.

If an NAI is configured for an OSU server, clients connect to the OSU AP through OSEN OSU. If no NAI is configured for an OSU server, clients connects to the OSU AP through Open OSU.

Examples

# Configure an NAI for OSU server 1.

<Sysname> system-view

[Sysname] wlan osu-provider 1

[Sysname-wlan-osu-1] nai joe@example.com

nai-realm

Use nai-realm to create a Network Access Identifier (NAI) realm and specify an authentication type for the NAI realm.

Use undo nai-realm to delete an NAI realm.

Syntax

nai-realm realm-name eap-method eap-method-id auth-method auth-method-id authentication authentication

undo nai-realm realm-name [ eap-method eap-method [ auth-method auth-method [ authentication authentication ] ] ]

Default

No NAI realm is created.

Views

Hotspot 2.0 policy view

Predefined user roles

network-admin

Parameters

name: Specifies an NAI realm by its name, a case-sensitive string of 1 to 255 characters.

eap-method eap-method-id: Specifies an EAP authentication method by its ID.

Table 4 EAP authentication method

eap-method-id

Description

1

EAP-Transport Layer Security (EAP-TLS)

2

Lightweight Extensible Authentication Protocol (LEAP)

3

EAP for GSM Subscriber Identity Module (EAP-SIM)

4

EAP-Tunneled Transport Layer Security (EAP-TTLS)

5

EAP-Authentication and Key Agreement(EAP-AKA)

6

Protected EAP (PEAP)

 

auth-method auth-method-id: Specifies an authentication method by its ID.

authentication authentication: Specifies an authentication parameter by its ID.

Table 5 Authentication method and authentication parameter

auth-method-id

auth-method-type

authentication

2

Non-EAP Inner Authentication Type

·     1PAP.

·     2CHAP.

·     3MSCHAP.

·     4MSCHAPV2.

5

Credential Type

·     1—SIM.

·     2—USIM.

·     3—NFC Secure Element.

·     4—Hardware Token.

·     5—Softoken.

·     6—Certificate.

·     7—username/password.

·     8—none*.

6

Tunneled EAP Method Credential Type

·     1SIM.

·     2USIM.

·     3NFC Secure Element.

·     4Hardware Token.

·     5Softoken.

·     6Certificate.

·     7username/password.

·     8Reserved.

·     9Anonymous.

 

Usage guidelines

When you use the undo nai-realm command, follow these guidelines:

·     The undo nai-realm realm-name command deletes all NAI realms that use the same name.

·     The undo nai-realm realm-name eap-method eap-method-id command to delete all NAI realms that use the same name and EAP authentication method.

·     The undo nai-realm realm-name eap-method eap-method-id auth-method auth-method-id command deletes all NAI realms that use the same name, EAP authentication method, and authentication method.

·     The undo nai-realm realm-name eap-method eap-method-id auth-method auth-method-id authentication authentication command deletes all NAI realms that use the same name, EAP authentication method, authentication method, and authentication parameter.

You can configure a maximum of 32 NAI realm names in a Hotspot 2.0 policy.

Examples

# Specify the authentication type for the NAI realm wifi in Hotspot 2.0 policy 1.

<Sysname> system-view

[Sysname] wlan hotspot-policy 1

[Sysname-wlan-hs-1] nai-realm wifi eap-method 2 auth-method 5 authentication 1

network-type

Use network-type to set the access network type.

Use undo network-type to restore the default.

Syntax

network-type network-type [ access-internet ]

undo network-type

Default

The access network type is not set.

Views

Hotspot 2.0 policy view

Predefined user roles

network-admin

Parameters

network-type: Specifies a network type in the range of 0 to 5, 14, and 15.

Table 6 Access network type

Value

Description

0

Private network

1

Private network with guest access

2

Chargeable public network

3

Free public network

4

Personal device network

5

Emergency services only network

14

Test or experimental

15

Wildcard

 

access-internet: Enables access to the Internet. If you do not specify this keyword, the Internet cannot be accessed.

Usage guidelines

Make sure all service templates bound to the Hotspot 2.0 policy are disabled before you set the access network type.

Examples

# Set the access network type to 1 and enable access to the Internet.

<Sysname> system-view

[Sysname] wlan hotspot-policy 1

[Sysname-wlan-hs-1] network-type 1 access-internet

operator-name

Use operator-name to set service provider information.

Use undo operator-name to remove the configuration.

Syntax

operator-name operator-name lang-code lang-code

undo operator-name operator-name lang-code lang-code

Default

No service provider name is set.

Views

Hotspot 2.0 policy view

Predefined user roles

network-admin

Parameters

operator-name: Specifies a service provider by its name, a case-sensitive string of 1 to 252 characters.

lang-code: Specifies a language code. The device supports both the ISO-639-1 and ISO-639-2 standards.

Usage guidelines

You can configure a maximum of 32 service provider and language code combinations in a Hotspot 2.0 policy.

Examples

# Set the language code to en for the service provider cmcc.

<Sysname> system-view

[Sysname] wlan hotspot-policy 1

[Sysname-wlan-hs-1] operator-name cmcc lang-code en

osu-provider

Use osu-provider to bind an OSU server to a Hotspot 2.0 policy.

Use undo osu-provider to unbind an OSU server from a Hotspot 2.0 policy.

Syntax

osu-provider osu-provider-number

undo osu-provider osu-provider-number

Default

No OSU server is bound to a Hotspot 2.0 policy.

Views

Hotspot policy view

Predefined user roles

network-admin

Parameters

osu-provider-number: Specifies an OSU server by its number, in the range of 1 to 32. The specified OSU server must exist.

Usage guidelines

This command is available only for version 2 of Hotspot 2.0.

You can bind a maximum of 32 OSU servers to a Hotspot 2.0 policy.

Before binding an OSU server to a Hotspot 2.0 policy, make sure you have finished the following configuration:

·     Set a name for the OSU server.

·     Specify a URI for the OSU server.

·     Specify a protocol for clients to communicate with the OSU server.

·     Specify an icon for the OSU server.

Examples

# Bind OSU server 1 to Hotspot 2.0 policy 1.

<Sysname> system-view

[Sysname] wlan hotspot-policy 1

[Sysname-wlan-hs-1] osu-provider 1

Related commands

friendly-name

icon-file

method

uri

wlan osu-provider

osu-ssid

Use osu-ssid to set an SSID for online signup services.

Use undo osu-ssid to delete the configured SSID for online signup services.

Syntax

osu-ssid ssid-name

undo osu-ssid

Default

No SSID is set for online signup services.

Views

Hotspot policy view

Predefined user roles

network-admin

Parameters

ssid-name: Specifies an SSID name, a case-sensitive string of 1 to 32 characters.

Usage guidelines

This command is available only for version 2 of Hotspot 2.0.

Make sure the configured SSID for online signup services is the same as the SSID for the online signup service template.

Examples

# Set the SSID for online signup services to osu.

<Sysname> system-view

[Sysname] wlan hotspot-policy 1

[Sysname-wlan-hs-1] osu-ssid osu

policy-name

Use policy-name to set a name for a Hotspot 2.0 policy.

Use undo policy-name to restore the default.

Syntax

policy-name name

undo policy-name

Default

A Hotspot 2.0 policy does not have a name.

Views

Hotspot 2.0 policy view

Predefined user roles

network-admin

Parameters

name: Specifies a Hotspot 2.0 policy by its name, a case-insensitive string of 1 to 32 characters.

Examples

# Set the name of Hotspot 2.0 policy 1 to market.

<Sysname> system-view

[Sysname] wlan hotspot-policy 1

[Sysname-wlan-hs-1] policy-name market

roam-oi

Use roam-oi to set an organization identifier (OI).

Use undo roam-oi to delete an OI.

Syntax

roam-oi oi [ in-beacon ]

undo roam-oi oi

Default

No OI is set.

Views

Hotspot 2.0 policy view

Predefined user roles

network-admin

Parameters

oi: Specifies an OI that can uniquely identify a roaming consortium, a six-digit or ten-digit hexadecimal code.

in-beacon: Adds an OI to beacons. As a best practice, specify this keyword for clients to get OIs.

Usage guidelines

Make sure all service templates bound to the Hotspot 2.0 policy are disabled before you set an OI.

You can configure a maximum of 32 OIs in a Hotspot 2.0 policy, and can add a maximum of three OIs to beacons.

Examples

# Set the OI to 004096 and add the OI to beacons.

<Sysname> system-view

[Sysname] wlan hotspot-policy 1

[Sysname-wlan-hs-1] roam-oi 004096 in-beacon

uri

Use uri to specify the URI of an OSU server.

Use undo uri to delete the configured URI of an OSU server.

Syntax

uri uri

undo uri

Default

No URI is specified for an OSU server.

Views

OSU server view

Predefined user roles

network-admin

Parameters

uri: Specifies the URI of an OSU server, a case-sensitive string of 1 to 255 characters.

Usage guidelines

This command is available only for version 2 of Hotspot 2.0.

Clients use the configured URI to visit the OSU server and perform online signup.

If an OSU server is already bound to a Hotspot 2.0 policy, you cannot delete the configured URI of the server.

Examples

# Specify the URI of OSU server 1.

<Sysname> system-view

[Sysname] wlan osu-provider 1

[Sysname-wlan-osu-1] uri https://osu-server.r2-testbed.wi-fi.org/

venue group

Use venue group to set venue group information for an AP.

Use undo venue group to restore the default.

Syntax

venue group venue-group-number type venue-type-number

undo venue group

Default

No venue group information is set for an AP.

Views

AP view

Predefined user roles

network-admin

Parameters

venue-group-number: Specifies a venue group by its number, in the range of 1 to 11.

Table 7 Venue group number and description

Number

Description

1

Assembly

2

Business

3

Educational

4

Factory

5

Institutional

6

Mercantile

7

Residential

8

Storage

9

Utility

10

Vehicular

11

Outdoor

 

venue-type-number: Specifies a venue type by its number. The value depends on the venue group number. For more information, see Table 8.

Table 8 Venue type number and description

Venue group number

Venue type number

Venue description

1

0

Unspecified

1

1

Arena

1

2

Stadium

1

3

Passenger Terminal

1

4

Amphitheater

1

5

Amusement Park

1

6

Place of Worship

1

7

Convention Center

1

8

Library

1

9

Museum

1

10

Restaurant

1

11

Theater

1

12

Bar

1

13

Coffee Shop

1

14

Zoo or Aquarium

1

15

Emergency Coordination Center

2

0

Unspecified

2

1

Doctor or Dentist office

2

2

Bank

2

3

Fire Station

2

4

Police Station

2

6

Post Office

2

7

Professional Office

2

8

Research and Development Facility

2

9

Attorney Office

3

0

Unspecified

3

1

School Primary

3

2

School Secondary

3

3

University or College

4

0

Unspecified

4

1

Factory

5

0

Unspecified

5

1

Hospital

5

2

Long-Term Care Facility

5

3

Alcohol and Drug Rehabilitation Center

5

4

Group Home

5

5

Prison or Jail

6

0

Unspecified

6

1

Retail Store

6

2

Grocery Market

6

3

Automotive Service Station

6

4

Shopping Mall

6

5

Gas Station

7

0

Unspecified

7

1

Private Residence

7

2

Hotel or Motel

7

3

Dormitory

7

4

Boarding House

8

0

Unspecified

9

0

Unspecified

10

0

Unspecified

10

1

Automobile or Truck

10

2

Airplane

10

3

Bus

10

4

Ferry

10

5

Ship or Boat

10

6

Train

10

7

Motor Bike

11

0

Unspecified

11

1

Muni-mesh Network

11

2

City Park

11

3

Rest Area

11

4

Traffic Control

11

5

Bus Stop

11

6

Kiosk

 

Examples

# Specify venue group 1 and venue type 2 for AP ap3.

<Sysname> system-view

[Sysname] wlan ap ap3 model WA4320i-ACN

[Sysname-wlan-ap-ap3] venue group 1 type 2

venue name

Use venue name to set a venue name for an AP.

Use undo venue name to remove the configuration.

Syntax

venue name venue-name lang-code lang-code

undo venue name venue-name lang-code lang-code

Default

No venue name is set for an AP.

Views

AP view

Predefined user roles

network-admin

Parameters

venue-name: Specifies a venue by its name, a case-sensitive string of 1 to 252 characters.

lang-code: Specifies the language code for a venue. The device supports both the ISO-639-1 and ISO-639-2 standards.

Usage guidelines

One venue can have multiple language codes.

You can configure a maximum of 32 venue name and language code combinations for an AP.

Examples

# Set the venue name to office and language codes to en for the AP ap3.

<Sysname> system-view

[Sysname] wlan ap ap3 model WA2610E-AGN

[Sysname-wlan-ap-ap3] venue name office lang-code en

wan-metrics

Use wan-metrics to set WAN link status parameters.

Use undo wan-metrics to restore the default.

Syntax

wan-metrics { link-down | link-test | link-up } [ asymmetric downlink-speed downlink-speed uplink-speed uplink-speed | symmetric link-speed link-speed ]

undo wan-metrics

Default

No WAN link status parameters are set.

Views

Hotspot 2.0 policy view

Predefined user roles

network-admin

Parameters

link-down: Sets the link status for the WAN to down.

link-test: Sets the link status for the WAN to testing.

link-up: Sets the link status for the WAN to up.

asymmetric: Specifies the asymmetric link.

downlink-speed downlink-speed: Specifies the downlink speed in the range of 1 to 4194304 Kbps.

uplink-speed uplink-speed: Specifies the uplink speed in the range of 1 to 4194304 Kbps.

symmetric: Specifies the symmetric link.

link-speed link-speed: Specifies the symmetric link speed in the range of 1 to 4194304 Kbps.

Examples

# Set the link status to up and the symmetric link rate to 67 Kbps for the WAN.

<Sysname> system-view

[Sysname] wlan hotspot-policy 1

[Sysname-wlan-hs-1] wan-metrics link-up symmetric link-speed 67

wlan hotspot-policy

Use wlan hotspot-policy to create a Hotspot 2.0 policy and enter its view, or enter the view of an existing Hotspot 2.0 policy.

Use undo wlan hotspot-policy to delete a Hotspot 2.0 policy.

Syntax

wlan hotspot-policy policy-number

undo wlan hotspot-policy policy-number

Default

No Hotspot 2.0 policies exist.

Views

System view

Predefined user roles

network-admin

Parameters

policy-number: Specifies the number of a Hotspot 2.0 policy, in the range of 1 to 32.

Usage guidelines

You cannot delete a Hotspot 2.0 policy that has been bound to a service template.

Examples

# Create Hotspot 2.0 policy 1 and enter its view.

<Sysname> system-view

[Sysname] wlan hotspot-policy 1

[Sysname-wlan-hs-1]

wlan hotspot osu-icon unload

Use wlan hotspot osu-icon unload to unload all OSU server icon files.

Syntax

wlan hotspot osu-icon unload

Views

System view

Predefined user roles

network-admin

Usage guidelines

This command is available only for version 2 of Hotspot 2.0.

This command only unloads OSU server icon files, and does not delete icon files.

Examples

# Unload all OSU server icon files.

<Sysname> system-view

[Sysname] wlan hotspot osu-icon unload

Related commands

icon-file

wlan hotspot osu-icon upload

wlan hotspot osu-icon upload

Use wlan hotspot osu-icon upload to load all the specified OSU server icon files.

Syntax

wlan hotspot osu-icon upload

Views

System view

Predefined user roles

network-admin

Usage guidelines

This command is available only for version 2 of Hotspot 2.0.

Use this command to load all icon files specified for an OSU server to validate the changes when icon file changes occur.

Examples

# Load all the specified OSU server icon files.

<Sysname> system-view

[Sysname] wlan hotspot osu-icon upload

Related commands

icon-file

wlan hotspot osu-icon unload

wlan osu-provider

Use wlan osu-provider to create an OSU server and enter its view, or enter the view of an existing OSU server.

Use undo wlan osu-provider to delete the specified OSU server.

Syntax

wlan osu-provider osu-provider-number

undo wlan osu-provider osu-provider-number

Default

No OSU server exists.

Views

System view

Predefined user roles

network-admin

Parameters

osu-provider-number: Specifies an OSU server by its number, in the range of 1 to 32.

Usage guidelines

This command is available only for version 2 of Hotspot 2.0.

You cannot delete an OSU server that has been bound to a Hotspot 2.0 policy.

Examples

# Create OSU server 1 and enter its view.

<Sysname> system-view

[Sysname] wlan osu-provider 1

[Sysname-wlan-osu-1]