00-About the H3C S12500-X & S12500X-AF Command References

HomeSupportResource CenterH3C S12500-X & S12500X-AF Switch Series Command References(R115x)-6W10200-About the H3C S12500-X & S12500X-AF Command References
Download Book
Table of Contents
Related Documents

About the H3C S12500-X & S12500X-AF command references

CAUTION

CAUTION:

·     Software Release 11xx applies only to F-series LPUs, which have an F in their card identifiers (for example, LSXM1TGS48FX1). S12500-X E-series LPUs (for example, LSX2TGS48EA1) or S12500X-AF H-series LPUs (for example, LSXM1CGQ36HB1) cannot run the software.

·     Do not install an F-series LPU and an E-series LPU on the same S12500-X switch. Do not install an F-series LPU and an H-series LPU on the same S12500X-AF switch.

 

The H3C S12500-X & S12500X-AF command references describe the commands and command syntax options available for the H3C S12500-X & S12500X-AF Switch Series running Release 1150 and later.

 

Command reference

Content

Fundamentals Command Reference

Covers the commands for logging in to and setting up the switch. This command reference includes:

·     Basic CLI

·     Login management

·     RBAC

·     FTP and TFTP

·     File system management

·     Configuration file management

·     Software upgrade

·     ISSU

·     Device management

·     Python

·     License

·     Preprovisioning

Virtual Technologies Command Reference

Covers the commands for configuring the virtual technologies. This command reference includes:

·     IRF

·     MDC

Layer 2—LAN Switching Command Reference

Covers the commands for configuring Layer 2 technologies and features in a LAN switched network. This command reference includes:

·     Ethernet interface

·     Loopback, null, and inloopback interface

·     Bulk interface configuration

·     MAC address table and MAC Information

·     Ethernet link aggregation

·     Port isolation

·     Spanning tree

·     Loop detection

·     VLAN

·     VLAN mapping

·     LLDP

·     Service loopback group

Layer 3—IP Services Command Reference

Covers the commands for configuring IP addressing, IP performance optimization, ARP, IP forwarding basic, DHCP, DNS, UDP helper, IPv6,Tunnel, GRE and DHCPv6. This command reference includes:

·     ARP (including gratuitous ARP and proxy ARP)

·     IP addressing

·     DHCP

·     DNS

·     Basic IP forwarding and load sharing

·     IRDP

·     IP performance optimization

·     UDP helper

·     IPv6

·     DHCPv6

·     Tunnel

·     GRE

Layer 3—IP Routing Command Reference

Covers the commands for configuring routes for IPv4 networks of different sizes. This command reference includes:

·     Basic IP routing

·     Static routing

·     RIP

·     OSPF

·     IS-IS

·     BGP

·     Policy-based routing

·     IPv6 static routing

·     RIPng

·     OSPFv3

·     IPv6 IS-IS

·     IPv6 Policy-based routing

·     Routing policy

IP Multicast Command Reference

Covers the commands for Layer 3 IPv4 multicast protocols (IGMP and PIM), Layer 2 IPv4 multicast protocols (IGMP snooping) and Layer 2 IPv6 multicast protocols (MLD snooping). This command reference includes:

·     IGMP snooping

·     Multicast routing and forwarding

·     IGMP

·     PIM

·     MSDP

·     MLD Snooping

MPLS Command Reference

Covers the commands for configuring basic MPLS and extended MPLS functions. This command reference includes:

·     Basic MPLS

·     Static LSP

·     LDP

·     MPLS TE

·     Static CRLSP

·     RSVP

·     Tunnel policy

·     MPLS L3VPN

·     MCE (including MCE and IPv6 MCE)

ACL and QoS Command Reference

Covers the commands for classifying traffic with ACLs, and allocating network resources and managing congestions with QoS technologies to improve network performance and network use efficiency. This command reference includes:

·     ACL

·     QoS, including the following:

?     QoS policy

?     Priority mapping

?     GTS and rate limit

?     Congestion management

?     Aggregate CAR

·     Time range

·     Data buffer

Security Command Reference

Covers security feature commands. Available security features include identity authentication, secure management, and attack protection. This command reference includes:

·     AAA

·     Password control

·     Public key management

·     PKI

·     SSL

·     IPsec and IKE

·     SSH

·     IP source guard

·     ARP attack protection

·     uRPF

·     FIPS

·     Attack detection and prevention

High Availability Command Reference

Covers high availability commands for managing failure detection and failover. Failure detection technologies focus on fault detection and isolation. Failover technologies focus on network recovery. This command reference includes:

·     Ethernet OAM

·     DLDP

·     RRPP

·     VRRP

·     BFD

·     Track

Network Management and Monitoring Command Reference

Covers the commands that help you manage and monitor your network, for example, manage system events, and test network connectivity. This command reference includes:

·     System maintenance and debugging (ping, tracert, and system debugging)

·     NTP and SNTP

·     Information center

·     SNMP

·     RMON

·     Sampler

·     Mirroring (including both port and traffic mirroring)

·     sFlow

·     EAA

·     NQA

·     NETCONF

FCoE Command Reference

Covers the commands for configuring FCoE.

TRILL Command Reference

Covers the commands for configuring TRILL.

SPB Command Reference

Covers the commands for configuring SPB.

EVI Command Reference

Covers the commands for configuring EVI.

OpenFlow Command Reference

Covers the commands for configuring OpenFlow.

VXLAN Command Reference

Covers the commands for configuring VXLAN.