05-Layer 3 - IP Services Command Reference

HomeSupportResource CenterSwitchesH3C S7500X Switch SeriesH3C S7500X Switch SeriesTechnical DocumentsCommandCommand ReferencesH3C S7500X Switch Series Command References-Release758X-6W10005-Layer 3 - IP Services Command Reference
01-ARP commands
Title Size Download
01-ARP commands 195.46 KB

ARP commands

arp check enable

Use arp check enable to enable dynamic ARP entry check.

Use undo arp check enable to disable dynamic ARP entry check.

Syntax

arp check enable

undo arp check enable

Default

Dynamic ARP entry check is enabled.

Views

System view

Predefined user roles

network-admin

mdc-admin

Usage guidelines

Dynamic ARP entry check disables a device from supporting dynamic ARP entries with multicast MAC addresses. The device cannot learn dynamic ARP entries containing multicast MAC addresses. You cannot manually add static ARP entries that contain multicast MAC addresses.

When dynamic ARP entry check is disabled, ARP entries containing multicast MAC addresses are supported. The device can learn dynamic ARP entries containing multicast MAC addresses obtained from the ARP packets sourced from a unicast MAC address. You can also manually add static ARP entries containing multicast MAC addresses.

Examples

# Enable dynamic ARP entry check.

<Sysname> system-view

[Sysname] arp check enable

arp check log enable

Use arp check log enable to enable the ARP logging feature.

Use undo arp check log enable to disable the ARP logging feature.

Syntax

arp check log enable

undo arp check log enable

Default

ARP logging is disabled.

Views

System view

Predefined user roles

network-admin

mdc-admin

Usage guidelines

This feature enables a device to log ARP events when ARP cannot resolve IP addresses correctly. The log information helps administrators locate and solve problems. The device can log the following ARP events:

·           On a proxy ARP-disabled interface, the target IP address of a received ARP packet is not one of the following IP addresses:

¡  The IP address of the receiving interface.

¡  The virtual IP address of the VRRP group.

·           The sender IP address of a received ARP reply conflicts with one of the following IP addresses:

¡  The IP address of the receiving interface.

¡  The virtual IP address of the VRRP group.

The device sends ARP log messages to the information center. You can use the info-center source command to specify the log output rules for the information center. For more information about information center, see Network Management and Monitoring Configuration Guide.

The device can generate a large number of ARP logs. To conserve system resources, enable ARP logging only when you are auditing or troubleshooting ARP events.

Examples

# Enable ARP logging.

<Sysname> system-view

[Sysname] arp check log enable

arp mac-interface-consistency check enable

Use arp mac-interface-consistency check enable to enable interface consistency check between ARP and MAC address entries.

Use undo arp mac-interface-consistency check enable to disable this feature.

Syntax

arp mac-interface-consistency check enable

undo arp mac-interface-consistency check enable

Default

Interface consistency check between ARP and MAC address entries is disabled.

Views

System view

Predefined user roles

network-admin

mdc-admin

Usage guidelines

In an unstable network, the receiving interface for packets from a user might change. The interface in the MAC address entry can be updated immediately while the interface in the ARP entry cannot. In this case, the packets matching the ARP entry will be sent out of an incorrect interface. To solve this problem, you can use this feature to periodically check the interface consistency between the ARP and MAC address entry for a user. If the interfaces are not the same, ARP sends ARP requests in the VLAN of the ARP entry and updates the entry with the ARP reply receiving interface.

Use display mac-address to display MAC address entries.

Examples

# Enable interface consistency check between ARP and MAC address entries.

<Sysname> system-view

[Sysname] arp mac-interface-consistency check enable

Related commands

display mac-address (Layer 2—LAN Switching Command Reference)

arp max-learning-num

Use arp max-learning-num to set the dynamic ARP learning limit for an interface.

Use undo arp max-learning-num to restore the default.

Syntax

arp max-learning-num max-number [ alarm alarm-threshold ]

undo arp max-learning-num

Default

The dynamic ARP learning limit for an interface depends on the maximum free space of the ARP table.

Views

Layer 2 Ethernet interface view

Layer 2 aggregate interface view

Layer 3 Ethernet interface view

Layer 3 Ethernet subinterface view

Layer 3 aggregate interface view

Layer 3 aggregate subinterface view

VXLAN VSI interface view

VLAN interface view

Predefined user roles

network-admin

mdc-admin

Parameters

max-number: Specifies the maximum number of dynamic ARP entries for an interface. The value range for this argument is 0 to 184320.

alarm alarm-threshold: Specifies an alarm threshold for dynamic ARP learning, in percentage. The value range for the alarm-threshold argument is 1 to 100. The device generates a log message when the number of dynamic ARP entries learned on an interface reaches the value calculated by using the formula: (max-number × alarm-threshold)/100. If you do not specify the alarm threshold, the device does not generate log messages.

Usage guidelines

An interface can dynamically learn ARP entries. To prevent an interface from holding too many ARP entries, you can set the maximum number of dynamic ARP entries that the interface can learn. When the maximum number is reached, the interface stops learning ARP entries.

When the number argument is set to 0, the interface is disabled from learning dynamic ARP entries.

Examples

# Specify VLAN-interface 40 to learn a maximum of 10 dynamic ARP entries.

<Sysname> system-view

[Sysname] interface vlan-interface 40

[Sysname-Vlan-interface40] arp max-learning-num 10

# Specify Ten-GigabitEthernet 1/0/1 to learn a maximum of 10 dynamic ARP entries.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] arp max-learning-num 10

# Specify Layer 2 aggregate interface Bridge-Aggregation 1 to learn a maximum of 10 dynamic ARP entries.

<Sysname> system-view

[Sysname] interface bridge-aggregation 1

[Sysname-Bridge-Aggregation1] arp max-learning-num 10

# Specify Layer 3 aggregate interface Route-Aggregation 1 to learn a maximum of 10 dynamic ARP entries.

<Sysname> system-view

[Sysname] interface route-aggregation 1

[Sysname-Route-Aggregation1] arp max-learning-num 10

arp max-learning-number

Use arp max-learning-number to set the dynamic ARP learning limit for a device.

Use undo arp max-learning-number to restore the default.

Syntax

In standalone mode:

arp max-learning-number max-number slot slot-number

undo arp max-learning-number slot slot-number

In IRF mode:

arp max-learning-number max-number chassis chassis-number slot slot-number

undo arp max-learning-number chassis chassis-number slot slot-number

Default

The dynamic ARP learning limit for a device depends on the maximum free space of the ARP table.

Views

System view

Predefined user roles

network-admin

mdc-admin

Parameters

max-number: Specifies the maximum number of dynamic ARP entries for a device. The value range for this argument is 0 to 184320.

slot slot-number: Specifies a card by its slot number. (In standalone mode.)

chassis chassis-number slot slot-number: Specifies a card on an IRF member device. The chassis-number argument represents the member ID of the IRF member device. The slot-number argument represents the slot number of the card. (In IRF mode.)

Usage guidelines

A device can dynamically learn ARP entries. To prevent a device from holding too many ARP entries, you can set the maximum number of dynamic ARP entries that the device can learn. When the maximum number is reached, the device stops learning ARP entries.

When the number argument is set to 0, the device is disabled from learning dynamic ARP entries.

The ARP learning limit setting is not supported on switching fabrics.

Examples

# Set the ARP learning limit to 64 for slot 1.

<Sysname> system-view

[Sysname] arp max-learning-number 64 slot 1

arp mode uni

Use arp mode uni to configure a port as a customer-side port.

Use undo arp mode to restore the default.

Syntax

arp mode uni

undo arp mode

Default

A port operates as a network-side port.

Views

VLAN interface view

VXLAN VSI interface view

Predefined user roles

network-admin

mdc-admin

Usage guidelines

By default, the device associates an ARP entry with routing information when the device learns an ARP entry. The ARP entry provides the next hop information for routing. To save hardware resources, you can use this command to specify a port that connects to a user terminal as a customer-side port. The device will not associate the routing information with the learned ARP entries.

Examples

# Configure VLAN-interface 2 as a customer-side port.

<Sysname> system-view

[Sysname] interface vlan-interface 2

[Sysname-Vlan-interface2] arp mode uni

arp multiport

Use arp multiport to configure a multiport ARP entry.

Use undo arp to delete an ARP entry.

Syntax

arp multiport ip-address mac-address  vlan-id [ vpn-instance vpn-instance-name ]

undo arp ip-address [ vpn-instance-name ]

Default

No multiport ARP entries exist.

Views

System view

Predefined user roles

network-admin

mdc-admin

Parameters

ip-address: Specifies an IP address for the multiport ARP entry.

mac-address: Specifies a MAC address for the multiport ARP entry, in the format of H-H-H.

vlan-id: Specifies a VLAN for the multiport ARP entry, in the range of 1 to 4094. The specified VLAN must already exist.

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance to which the multiport ARP entry belongs. The vpn-instance-name argument represents the VPN instance name, a case-sensitive string of 1 to 31 characters. The specified VPN instance must already exist. To specify a multiport ARP entry on the public network, do not specify this option.

Usage guidelines

If the corresponding VLAN or the VLAN interface is deleted, the multiport ARP entry is also deleted.

To make the multiport ARP entry effective for packet forwarding, you must configure a multicast or multiport unicast MAC address entry to specify multiple output interfaces. The MAC address entry must have the same MAC address and VLAN ID as the multiport ARP entry. In addition, the IP address in the multiport ARP entry must reside on the same subnet as the VLAN interface of the specified VLAN.

Examples

# Configure a multiport ARP entry that contains IP address 202.38.10.2 and MAC address 00e0-fc01-0000 in VLAN 10.

<Sysname> system-view

[Sysname] arp multiport 202.38.10.2 00e0-fc01-0000 10

Related commands

display arp multiport

reset arp multiport

arp smooth

(In standalone mode.) Use arp smooth to synchronize ARP entries from the active MPU to all other cards.

(In IRF mode.) Use arp smooth to synchronize ARP entries from the global active MPU to all other cards.

Syntax

arp smooth

Views

User view

Predefined user roles

network-admin

mdc-admin

Examples

# (In standalone mode.) Synchronize ARP entries from the active MPU to all other cards.

<Sysname> arp smooth

# (In IRF mode.) Synchronize ARP entries from the global active MPU to all other cards.

<Sysname> arp smooth

arp static

Use arp static to configure a static ARP entry.

Use undo arp to delete an ARP entry.

Syntax

arp static ip-address mac-address [ vlan-id interface-type interface-number | vsi-interface vsi-interface-id tunnel number vsi vsi-name | vsi-interface vsi-interface-id interface-type interface-number service-instance instance-id vsi vsi-name ] [ vpn-instance vpn-instance-name ]

undo arp ip-address [ vpn-instance-name ]

Default

No static ARP entries exist.

Views

System view

Predefined user roles

network-admin

mdc-admin

Parameters

ip-address: Specifies an IP address for the static ARP entry.

mac-address: Specifies a MAC address for the static ARP entry, in the format of H-H-H.

vlan-id: Specifies the ID of a VLAN to which the static ARP entry belongs. The value range is 1 to 4094.

interface-type interface-number: Specifies an interface by its type and number.

vsi-interface vsi-interface-id: Specifies a VSI interface by its number. The VSI interface must already exist.

tunnel number: Specifies a tunnel interface by its number. The tunnel interface must already exist.

vsi vsi-name: Specifies a VSI by its name, a case-sensitive string of 1 to 31 characters.

service-instance instance-id: Specifies an Ethernet service instance by its ID in the range of 1 to 4096. You must specify this option if you specify a Layer 2 Ethernet interface for the preceding interface-type interface-number arguments. Do not specify this option if you specify an interface of other types for the preceding interface-type interface-number argument.

vpn-instance vpn-instance-name: Specifies an MPLS L3VPN instance to which the static ARP entry belongs. The vpn-instance-name argument represents the VPN instance name, a case-sensitive string of 1 to 31 characters. The VPN instance must already exist. To specify a static ARP entry on the public network, do not specify this option.

Usage guidelines

A static ARP entry is manually configured and maintained. It does not age out and cannot be overwritten by any dynamic ARP entry.

Static ARP entries can be short or long.

A resolved short static ARP entry becomes unresolved upon certain events, for example, when the resolved output interface goes down, or the corresponding VLAN or VLAN interface is deleted.

Long static ARP entries are effective or ineffective. Ineffective long static ARP entries cannot be used for packet forwarding. A long static ARP entry is ineffective when any of the following conditions exists:

·           The IP address in the entry conflicts with a local IP address.

·           No local interface has an IP address in the same subnet as the IP address in the ARP entry.

If you specify the vlan-id interface-type interface-number argument, follow these restrictions and guidelines:

·           The interface can be an Ethernet interface or an aggregate interface.

·           The VLAN and VLAN interface must already exist. The specified Ethernet interface must belong to the specified VLAN.

·           The IP address of the VLAN interface and the IP address specified by the ip-address argument must be on the same network.

·           A long static ARP entry for a VLAN is deleted if the VLAN or VLAN interface is deleted.

On a VXLAN IP gateway that forwards traffic among VXLANs through VXLAN tunnels, a VSI interface can act as the gateway for multiple VXLANs. The VSI interface (input interface) might be connected to multiple VXLAN tunnel interfaces (output interfaces). In this case, you must specify the vsi-interface vsi-interface-id tunnel number vsi vsi-name parameters to identify a VSI interface-VSI-VXLAN tunnel interface binding. For more information about VSI interfaces, VSI, and VXLAN tunnel interfaces, see VXLAN configuration in VXLAN Configuration Guide.

On a VXLAN IP gateway that forwards traffic from multiple local sites to remote sites, a VSI interface can act as the gateway for multiple local sites. The VSI interface (input interface) might be associated with multiple Ethernet services (output interfaces) on Layer 2 Ethernet interfaces through which the VSI interface connects to the local sites. In this case, you must specify the vsi-interface vsi-interface-id interface-type interface-number service-instance instance-id vsi vsi-name parameters to identify a VSI interface-Layer 2 Ethernet interface-Ethernet service instance-VSI binding. For more information about VSI interfaces, VSI, and Ethernet service instances, see VXLAN configuration in VXLAN Configuration Guide.

Examples

# Configure a long static ARP entry that contains IP address 202.38.10.2, MAC address 00e0-fc01-0000, and output interface Ten-GigabitEthernet 1/0/1 in VLAN 10.

<Sysname> system-view

[Sysname] arp static 202.38.10.2 00e0-fc01-0000 10 ten-gigabitethernet 1/0/1

# Configure a long static ARP entry that contains IP address 1.1.1.1, MAC address 00e0-fc01-0000, input interface VSI-interface 1, output interface Tunnel 1, and the VSI a.

<Sysname> system-view

[Sysname] arp static 1.1.1.1 00e0-fc01-0000 vsi-interface 1 tunnel 1 vsi a

# Configure a long static ARP entry that contains IP address 1.1.1.1, MAC address 00e0-fc01-0000, input interface VSI-interface 1, output interface Ethernet instance 1 on GigabitEthernet 1/0/1, and VSI a.

<Sysname> system-view

[Sysname] arp static 1.1.1.1 00e0-fc01-0000 vsi-interface 1 gigabitethernet 1/0/1 service-instance 1 vsi a

Related commands

display arp

reset arp

arp timer aging

Use arp timer aging to set the aging timer for dynamic ARP entries.

Use undo arp timer aging to restore the default.

Syntax

arp timer aging { aging-minutes | second aging-seconds }

undo arp timer aging

Default

In system view, the aging timer for dynamic ARP entries is 20 minutes.

In interface view, the aging timer for dynamic ARP entries is the aging timer set in system view.

Views

System view

Layer 3 Ethernet interface view

Layer 3 Ethernet subinterface view

Layer 3 aggregate interface view

Layer 3 aggregate subinterface view

VXLAN VSI interface view

VLAN interface view

Predefined user roles

network-admin

mdc-admin

Parameters

aging-minutes: Specifies the aging timer in minutes. The value range for this argument is 1 to 1440.

second aging-seconds: Specifies the aging timer in seconds. The value range for the aging-seconds argument is 5 to 86400.

Usage guidelines

Each dynamic ARP entry in the ARP table has a limited lifetime, called an aging timer. The aging timer of a dynamic ARP entry is reset each time the dynamic ARP entry is updated. Dynamic ARP entries that are not updated before their aging timers expire are deleted from the ARP table.

You can set the aging timer for dynamic ARP entries in system view or in interface view. The aging timer set in interface view takes precedence over the aging timer set in system view.

Set the aging timer for dynamic ARP entries as needed. For example, when you configure proxy ARP, set a short aging time so that invalid dynamic ARP entries can be deleted in a timely manner.

Examples

# Set the aging timer for dynamic ARP entries to 10 minutes.

<Sysname> system-view

[Sysname] arp timer aging 10

# Set the aging timer for dynamic ARP entries to 200 seconds.

<Sysname> system-view

[Sysname] arp timer aging second 200

# Set the aging timer for dynamic ARP entries to 200 seconds on VLAN-interface 2.

<Sysname> system-view

[Sysname] interface vlan-interface 2

[Sysname-Vlan-interface2] arp timer aging second 200

Related commands

arp timer aging probe-count

arp timer aging probe-interval

display arp timer aging

arp timer aging probe-count

Use arp timer aging probe-count to set the maximum number of probes for dynamic ARP entries.

Use undo arp timer aging probe-count to restore the default.

Syntax

arp timer aging probe-count count

undo arp timer aging probe-count

Default

In system view, the maximum number of probes is three for dynamic ARP entries.

In interface view, the maximum number of probes for dynamic ARP entries is the maximum probe count set in system view.

Views

System view

Layer 3 Ethernet interface view

Layer 3 Ethernet subinterface view

Layer 3 aggregate interface view

Layer 3 aggregate subinterface view

VXLAN VSI interface view

VLAN interface view

Predefined user roles

network-admin

mdc-admin

Parameters

count: Specifies the maximum number of probes. The value range for this argument is 0 to 10. To disable the device from probing dynamic ARP entries, set the value to 0.

Usage guidelines

This probe mechanism keeps legal dynamic ARP entries valid and avoids unnecessary ARP resolution during later traffic forwarding. This probe feature sends ARP requests for the IP address in a dynamic ARP entry.

·           If the device receives an ARP reply before the entry aging timer expires, the device resets the aging timer.

·           If the device does not receive any ARP reply after the maximum number of probes is made, the device deletes the entry when the entry aging timer expires.

You can set the maximum number of probes in system view and in interface view. The probe count set in interface view takes precedence over the probe count set in system view.

Examples

# Allow the device to perform a maximum of five probes for dynamic ARP entries.

<Sysname> system-view

[Sysname] arp timer aging probe-count 5

# Allow the device to perform a maximum of five probes for dynamic ARP entries on VLAN-interface 2.

<Sysname> system-view

[Sysname] interface vlan-interface 2

[Sysname-Vlan-interface2] arp timer aging probe-count 5

Related commands

arp timer aging

arp timer aging probe-interval

arp timer aging probe-interval

Use arp timer aging probe-interval to set the interval for probing dynamic ARP entries.

Use undo arp timer aging probe-interval to restore the default.

Syntax

arp timer aging probe-interval interval

undo arp timer aging probe-interval

Default

In system view, the probe interval is 5 seconds.

In interface view, the probe interval equals the setting in system view.

Views

System view

Layer 3 Ethernet interface view

Layer 3 Ethernet subinterface view

Layer 3 aggregate interface view

Layer 3 aggregate subinterface view

VXLAN VSI interface view

VLAN interface view

Predefined user roles

network-admin

mdc-admin

Parameters

Interval: Specifies the probe interval in seconds. The value rang is 1 to 60.

Usage guidelines

The probing feature keeps legal dynamic ARP entries valid and avoids unnecessary ARP resolution during later traffic forwarding.

Before a dynamic ARP entry is aged out, the device sends ARP requests for the IP address in the ARP entry.

·           If the device receives an ARP reply during the probe interval, the device resets the aging timer.

·           If the device does not receive any ARP reply during the probe interval, the device starts a new probe.

·           If the maximum number probes are made, and still no ARP reply is received, the device deletes the entry.

You can set the probe interval in system view and in interface view. The probe interval in interface view takes precedence over the probe interval in system view.

Examples

# Set the probe interval to 10 seconds for dynamic ARP entries.

<Sysname> system-view

[Sysname] arp timer aging probe-interval 10

# Set the probe interval to 10 seconds for dynamic ARP entries on VLAN-interface 2.

<Sysname> system-view

[Sysname] interface vlan-interface 2

[Sysname-Vlan-interface2] arp timer aging probe-interval 10

Related commands

arp timer aging

arp timer aging probe-count

arp user-ip-conflict record enable

Use arp user-ip-conflict record enable to enable recording user IP address conflicts.

Use undo arp user-ip-conflict record enable to disable recording user IP address conflicts.

Syntax

arp user-ip-conflict record enable

undo arp user-ip-conflict record enable

Default

Recording user IP address conflicts is disabled.

Views

System view

Predefined user roles

network-admin

mdc-admin

Usage guidelines

This feature enables the device to detect and record user IP address conflicts. The device determines that a conflict occurs if an incoming non-gratuitous ARP packet has the same sender IP address as an existing ARP entry but a different sender MAC address. The device generates a user IP address conflict record, logs the conflict, and sends the log to the information center. For information about the log destination and output rule configuration, see the information center in Network Management and Monitoring Configuration Guide.

A card can generate a maximum of 10 user IP address conflict logs per second.

To display user IP address conflict records, use the display arp user-ip-conflict record command.

Examples

# Enable recording user IP address conflicts.

<Sysname> system-view

[Sysname] arp user-ip-conflict record enable

Related commands

display arp user-ip-conflict record

arp user-move record enable

Use user-move record enable to enable recording user port migrations.

Use undo arp user-move record enable to disable recording user port migrations.

Syntax

arp user-move record enable

undo arp user-move record enable

Default

Recording user port migrations is disabled.

Views

System view

Predefined user roles

network-admin

mdc-admin

Usage guidelines

Each card can generate a maximum of 10 user port migration logs per second.

To display user port migration records, use the display arp user-move record command.

Examples

# Enable recording user port migration.

<Sysname> system-view

[Sysname] arp user-move record enable

Related commands

display arp user-move record

display arp

Use display arp to display ARP entries.

Syntax

In standalone mode:

display arp [ [ all | dynamic | multiport | static ] [ slot slot-number ] | vlan vlan-id | interface interface-type interface-number ] [ count | verbose ]

In IRF mode:

display arp [ [ all | dynamic | multiport | static ] [ chassis chassis-number slot slot-number ] | vlan vlan-id | interface interface-type interface-number ] [ count | verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

all: Displays all ARP entries.

dynamic: Displays dynamic ARP entries.

multiport: Displays multiport ARP entries.

static: Displays static ARP entries.

slot slot-number: Specifies a card by its slot number. If you do not specify a card, this command displays ARP entries for the active MPU. (In standalone mode.)

chassis chassis-number slot slot-number: Specifies a card on an IRF member device. The chassis-number argument represents the member ID of the IRF member device. The slot-number argument represents the slot number of the card. If you do not specify a card, this command displays ARP entries for the global active MPU. (In IRF mode.)

vlan vlan-id: Specifies a VLAN by its VLAN ID. The VLAN ID is in the range of 1 to 4094.

interface interface-type interface-number: Specifies an interface by its type and number. If you do not specify an interface, this command displays ARP entries for all interfaces.

count: Displays the number of ARP entries.

verbose: Displays detailed information about ARP entries.

Usage guidelines

This command displays information about ARP entries, including the IP address, MAC address, VLAN ID, output interface, entry type, and aging timer.

Examples

# Display all ARP entries.

<Sysname> display arp all

  Type: S-Static   D-Dynamic   O-Openflow   R-Rule   M-Multiport  I-Invalid

IP address      MAC address    VLAN/VSI   Interface                Aging Type

1.1.1.1          02e0-f102-0023 1         XGE1/0/1                 --    S

1.1.1.2          00e0-fc00-0001 12        XGE1/0/2                 960   D

1.1.1.3          00e0-fe50-6503 12        Tunnel1                  960   D

1.1.1.4          00e0-fe60-5000 0         --                       --    M

# Display detailed information about all ARP entries.

IP address          : 1.1.1.1             MAC address    : 02e0-f102-0023

Type                : Static              Aging          : --

Interface           : XGE1/0/1             VLAN           : 1

VPN instance        : --

Link ID             : --

Service instance    : 1

VXLAN ID            : --

VSI name            : --

VSI interface       : --

Nickname            : 0x0000

 

IP address          : 1.1.1.2             MAC address    : 0015-e944-adc5

Type                : Dynamic             Aging          : 960 sec

Interface           : XGE1/0/2             VLAN           : 12

VPN instance        : --

Link ID             : --

Service instance    : --

VXLAN ID            : --

VSI name            : --

VSI interface       : --

Nickname            : 0x0000

 

IP address          : 1.1.1.3             MAC address    : 0013-1234-0001

Type                : Dynamic             Aging          : 960 sec

Interface           : Tunnel1             VLAN           : 12

VPN instance        : --

Link ID             : 0x5000001

Service instance    : --

VXLAN ID            : --

VSI name            : vpna

VSI interface       : Vsi1

Nickname            : 0x0000

 

IP address          : 1.1.1.4                  MAC address    : 00e0-fe60-5000

Type                : Multiport                Aging          : --

Interface           : --                       VLAN           : --

VPN instance        : --

Link ID             : --

Service instance    : --

VXLAN ID            : 1

VSI name            : vpna

VSI interface       : Vsi1

Nickname            : 0x0000

# Display the number of all ARP entries.

<Sysname> display arp all count

 Total number of entries : 3

Table 1 Command output

Field

Description

IP address

IP address in an ARP entry.

MAC address

MAC address in an ARP entry.

VLAN/VSI

ID of the VLAN or index of the VSI to which the ARP entry belongs. This field displays hyphens (--) in either of the following situations:

·          The ARP entry is an unresolved short static ARP entry.

·          The output interface of the ARP entry does not belong to the VLAN or VSI.

Interface

Output interface in an ARP entry. This field displays hyphens (--) in either of the following situations:

·          The ARP entry is an unresolved short static ARP entry.

·          The ARP entry is a multiport ARP entry and has no output interface information.
To obtain the output interface information of the multiport ARP entry, look up the MAC address table according to the MAC address in the ARP entry.

NOTE:

In an IRF 3.1 system, ARP entries with a virtual management Ethernet interface as the output interface are generated for packet forwarding between PEXs and the parent fabric. For more information about IRF3.1, see Virtual Technologies Configuration Guide.

Link ID

Link ID in an ARP entry. This field displays hyphens (--) if the ARP entry does not belong to any VSI.

Aging

Aging time for an ARP entry in seconds.

For a static ARP entry, this field always displays hyphens (--). The static ARP entry never ages out unless you delete it manually.

For a dynamic ARP entry, this field displays hyphens (--) if the aging time is unknown.

Type

ARP entry type:

·          D—Dynamic.

·          S—Static.

·          O—OpenFlow.

·          R—Rule.

·          M—Multiport.

·          I—Invalid.

VPN instance

Name of VPN instance. If no VPN instance is configured for the ARP entry, this field displays hyphens (--).

Service instance

Ethernet service instance in an ARP entry. This field displays hyphens (--) if no Ethernet service instance is specified for the Layer 2 Ethernet interface or Layer 2 aggregate interface in the ARP entry.

VXLAN ID

ID of the VXLAN to which the ARP entry belongs. VXLAN ID is also called VNI. If the ARP entry does not belong to any VXLAN, this field displays hyphens (--).

VSI name

Name of the VSI to which the ARP entry belongs. If the ARP entry does not belong to any VSI, this field displays hyphens (--).

VSI interface

Name of the gateway interface of the VSI. If no gateway interface is specified for the VSI, this field displays hyphens (--).

Nickname

Nickname of the ARP entry. The nickname is a string of four hexadecimal numbers, for example, 012a.

Total number of entries

Number of ARP entries.

 

Related commands

arp static

reset arp

display arp entry-limit

Use display arp entry-limit to display the maximum number of ARP entries that a device supports.

Syntax

display arp entry-limit

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Examples

# Display the maximum number of ARP entries that the device supports.

<Sysname> display arp entry-limit

ARP entries: 184320

display arp ip-address

Use display arp ip-address to display the ARP entry for an IP address.

Syntax

In standalone mode:

display arp ip-address [ slot slot-number ] [ verbose ]

In IRF mode:

display arp ip-address [ chassis chassis-number slot slot-number ] [ verbose ]

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

ip-address: Displays the ARP entry for the specified IP address.

slot slot-number: Specifies a card by its slot number. If you do not specify a card, this command displays information for the active MPU. (In standalone mode.)

chassis chassis-number slot slot-number: Specifies a card on an IRF member device. The chassis-number argument represents the member ID of the IRF member device. The slot-number argument represents the slot number of the card. If you do not specify a card, this command displays information for the global active MPU. (In IRF mode.)

verbose: Displays the detailed information about the specified ARP entry.

Usage guidelines

The ARP entry information includes the IP address, MAC address, VLAN ID, output interface, entry type, and aging timer.

Examples

# Display the ARP entry for the IP address 20.1.1.1.

<Sysname> display arp 20.1.1.1

  Type: S-Static   D-Dynamic   O-Openflow   R-Rule   M-Multiport  I-Invalid

IP address      MAC address    VLAN/VSI   Interface                Aging Type

20.1.1.1        00e0-fc00-0001 --         --                       --    S

Related commands

arp static

reset arp

display arp openflow count

Use display arp openflow count to display the number of OpenFlow ARP entries.

Syntax

In standalone mode:

display arp openflow count [ slot slot-number ]

In IRF mode:

display arp openflow count [ chassis chassis-number slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

slot slot-number: Specifies a card by its slot number. If you do not specify a card, this command displays the number of OpenFlow ARP entries for the active MPU. (In standalone mode.)

chassis chassis-number slot slot-number: Specifies a card on an IRF member device. The chassis-number argument represents the member ID of the IRF member device. The slot-number argument represents the slot number of the card. If you do not specify a card, this command displays the number of OpenFlow ARP entries for the global active MPU. (In IRF mode.)

Examples

# Display the number of OpenFlow ARP entries.

<Sysname> display arp openflow count

 Total number of OpenFlow ARP entries: 6

display arp timer aging

Use display arp timer aging to display the aging timer of dynamic ARP entries.

Syntax

display arp timer aging

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Usage guidelines

This command always displays the aging time in seconds no matter which unit you set in the arp timer aging command.

Examples

# Display the aging timer of dynamic ARP entries.

<Sysname> display arp timer aging

Current ARP aging time is 1200 seconds

Related commands

arp timer aging

display arp user-ip-conflict record

Use display arp user-ip-conflict record to display user IP address conflict records.

Syntax

In standalone mode:

display arp user-ip-conflict record [ slot slot-number ]

In IRF mode:

display arp user-ip-conflict record [ chassis chassis-number slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

slot slot-number: Specifies a card by its slot number. If you do not specify a card, this command displays user IP address conflict records for the active MPU. (In standalone mode.)

chassis chassis-number slot slot-number: Specifies a card on an IRF member device. The chassis-number argument represents the member ID of the IRF member device. The slot-number argument represents the slot number of the card. If you do not specify a card, this command displays user IP address conflict records for the global active MPU. (In IRF mode.)

Usage guidelines

Each card can save a maximum of 200 user IP address conflict records.

If the maximum number is reached, a new record will override the earliest record.

Examples

# Display all user IP address conflict records.

<Sysname> display arp user-ip-conflict record

IP address: 10.1.1.1

System time: 2018-02-02 11:22:29

Conflict count: 1

Log suppress count: 0

Old interface: Ten-GigabitEthernet1/0/1

New interface: Ten-GigabitEthernet1/0/2

Old SVLAN/CVLAN: 100/2

New SVLAN/CVLAN: 100/2

Old MAC: 00e0-ca63-8141

New MAC: 00e0-ca63-8142

 

IP address: 10.1.1.2

System time: 2018-02-02 10:20:30

Conflict count: 1

Log suppress count: 0

Old interface: Ten-GigabitEthernet1/0/1

New interface: Ten-GigabitEthernet1/0/2

Old SVLAN/CVLAN: 100/--

New SVLAN/CVLAN: 100/--

Old MAC: 00e0-ca63-8141

New MAC: 00e0-ca63-8142

Table 2 Command output

Field

Description

IP address

IP address of a  user.

System time

Time when the user IP address conflict occurred.

Conflict count

Number of times that conflicts for the IP address.

Log suppress count

Number of times that user IP address conflict logs are suppressed.

Old interface

Output interface in the old ARP entry.

New interface

Output interface in the new ARP entry.

Old SVLAN/CVLAN

ID of the outer VLAN or inner VLAN in the old ARP entry. This field displays hyphens (--) if the ARP entry does not belong to any outer VLAN or inner VLAN.

New SVLAN/CVLAN

ID of the outer VLAN or inner VLAN in the new ARP entry. This field displays hyphens (--) if the ARP entry does not belong to any outer VLAN or inner VLAN.

Old MAC

MAC address in the old ARP entry.

New MAC

MAC address in the new ARP entry.

 

Related commands

arp user-ip-conflict record enable

display arp user-move record

Use display arp user-move record to display user port migration records.

Syntax

In standalone mode:

display arp user-move record [ slot slot-number ]

In IRF mode:

display arp user-move record [ chassis chassis-number slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

slot slot-number: Specifies a card by its slot number. If you do not specify a card, this command displays user port migration records for the active MPU. (In standalone mode.)

chassis chassis-number slot slot-number: Specifies a card on an IRF member device. The chassis-number argument represents the member ID of the IRF member device. The slot-number argument represents the slot number of the card. If you do not specify a card, this command displays user port migration records for the global active MPU. (In IRF mode.)

Usage guidelines

Each card can save a maximum of 200 user port migration records.

When the number of user port migration records reaches the upper limit, new records will overwrite the earliest ones.

Examples

# Display all user port migration records.

<Sysname> display arp user-move record

IP address: 10.1.1.1

MAC address: 0001-0201-0e81

System time: 2018-02-02 11:22:29

Move count: 1

Log suppress count: 0

Before:

  interface: Ten-GigabitEthernet1/0/1

  SVLAN/CVLAN: 100/2

After:

  interface: Ten-GigabitEthernet1/0/2

  SVLAN/CVLAN: 100/2

 

IP address: 10.1.1.2

MAC address: 0001-0201-0e82

System time: 2018-02-02 10:20:30

Move count: 1

Log suppress count: 0

Before:

  interface: Ten-GigabitEthernet1/0/1

  SVLAN/CVLAN: 100/--

After:

  interface: Ten-GigabitEthernet1/0/2

  SVLAN/CVLAN: 100/--

Table 3 Command output

Field

Description

IP address

IP address of the user.

MAC address

MAC address of the user.

System time

Time when the user port migration occurred.

Move count

Number of times that user port migrated.

Log suppress count

Number of times that the generation of user port migration logs is suppressed.

Interface

Output interface in the ARP entry.

SVLAN/CVLAN

ID of the outer VLAN or inner VLAN in the ARP entry. This field displays hyphens (--) if the ARP entry does not belong to any outer VLAN or inner VLAN.

 

Related commands

arp user-move record enable

display arp vpn-instance

Use display arp vpn-instance to display the ARP entries for a VPN instance.

Syntax

display arp vpn-instance vpn-instance-name [ count ]

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

vpn-instance-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31 characters. The VPN instance name cannot contain any spaces.

count: Displays the number of ARP entries.

Usage guidelines

This command displays information about ARP entries for a VPN instance, including the IP address, MAC address, VLAN ID, output interface, entry type, and aging timer.

Examples

# Display ARP entries for VPN instance test.

<Sysname> display arp vpn-instance test

  Type: S-Static   D-Dynamic   O-Openflow   R-Rule   M-Multiport  I-Invalid

IP address      MAC address    VLAN/VSI   Interface                Aging Type

20.1.1.1        00e0-fc00-0001 N/A        N/A                      N/A   S

Related commands

arp static

reset arp

reset arp

Use reset arp to clear ARP entries from the ARP table.

Syntax

In standalone mode:

reset arp { all | dynamic | interface interface-type interface-number | multiport | slot slot-number | static }

In IRF mode:

reset arp { all | chassis chassis-number slot slot-number | dynamic | interface interface-type interface-number | multiport | static }

Views

User view

Predefined user roles

network-admin

mdc-admin

Parameters

all: Clears all ARP entries.

dynamic: Clears all dynamic ARP entries.

multiport: Clears all multiport ARP entries.

static: Clears all static ARP entries.

slot slot-number: Specifies a card by its slot number. If you do not specify a card, this command clears ARP entries for the active MPU. (In standalone mode.)

chassis chassis-number slot slot-number: Specifies a card on an IRF member device. The chassis-number argument represents the member ID of the IRF member device. The slot-number argument represents the slot number of the card. If you do not specify a card, this command clears ARP entries for the global active MPU. (In IRF mode.)

interface interface-type interface-number: Specifies an interface by its type and number. If you do not specify an interface, this command clears ARP entries for all interfaces.

Examples

# Clear all static ARP entries.

<Sysname> reset arp static

Related commands

arp static

display arp


Gratuitous ARP commands

arp ip-conflict log prompt

Use arp ip-conflict log prompt to enable IP conflict notification.

Use undo arp ip-conflict log prompt to restore the default.

Syntax

arp ip-conflict log prompt

undo arp ip-conflict log prompt

Default

IP conflict notification is disabled.

Views

System view

Predefined user roles

network-admin

mdc-admin

Usage guidelines

By default, the device performs the following operations if it is using the sender IP address of a received ARP packet:

·           Sends a gratuitous ARP request.

·           Displays an error message after the device receives an ARP reply about the conflict.

You can use this command to enable the device to display error messages before sending a gratuitous ARP reply or request for conflict confirmation.

Examples

# Enable IP conflict notification on the device.

<Sysname> system-view

[Sysname] arp ip-conflict log prompt

arp send-gratuitous-arp

Use arp send-gratuitous-arp to enable periodic sending of gratuitous ARP packets on an interface.

Use undo arp send-gratuitous-arp to disable the interface from periodically sending gratuitous ARP packets.

Syntax

arp send-gratuitous-arp [ interval interval ]

undo arp send-gratuitous-arp

Default

Periodic sending of gratuitous ARP packets is disabled.

Views

Layer 3 Ethernet interface view

Layer 3 Ethernet subinterface view

Layer 3 aggregate interface view

Layer 3 aggregate subinterface view

VXLAN VSI interface view

VLAN interface view

Predefined user roles

network-admin

mdc-admin

Parameters

interval interval: Specifies the sending interval in the range of 200 to 200000 milliseconds. The default value is 2000 milliseconds.

Usage guidelines

This feature takes effect on an interface only when the interface has an IP address and the data link layer state of the interface is up.

This feature can send gratuitous ARP requests only for a VRRP virtual IP address, or the sending interface's primary IP address or manually configured secondary IP address. The primary IP address can be configured manually or automatically, whereas the secondary IP address must be configured manually.

If you change the sending interval for gratuitous ARP packets, the configuration takes effect at the next sending interval.

The sending interval for gratuitous ARP packets might be much longer than the set interval when any of the following conditions exist:

·           This feature is enabled on multiple interfaces.

·           Each interface is configured with multiple secondary IP addresses.

·           A small sending interval is configured in the preceding cases.

Examples

# Enable VLAN-interface 2 to send gratuitous ARP packets every 300 milliseconds.

<Sysname> system-view

[Sysname] interface vlan-interface 2

[Sysname-Vlan-interface2] arp send-gratuitous-arp interval 300

gratuitous-arp mac-change retransmit

Use gratuitous-arp mac-change retransmit to set the times and the interval for retransmitting a gratuitous ARP packet for the device MAC address change.

Use undo gratuitous-arp mac-change retransmit to restore the default.

Syntax

gratuitous-arp mac-change retransmit times interval seconds

undo gratuitous-arp mac-change retransmit

Default

The device sends a gratuitous packet for its MAC address change once only.

Views

System view

Predefined user roles

network-admin

mdc-admin

Parameters

times: Specifies the times of retransmitting a gratuitous packet, in the range of 1 to 10.

interval seconds: Specifies the interval for retransmitting a gratuitous packet, in the range of 1 to 10 seconds.

Usage guidelines

The device sends a gratuitous ARP packet to inform other devices of its MAC address change. However, the other devices might fail to receive the packet because the device sends the gratuitous ARP packet once only by default. Use this command to configure gratuitous ARP retransmission parameters to ensure that the other devices can receive the packet.

After you execute this command, the device will retransmit a gratuitous ARP packet for its MAC address change at the specified interval for the specified times.

Examples

# Set the times to 3 and the interval to 5 for retransmitting a gratuitous ARP packet for the device MAC address change.

<Sysname> system-view

[Sysname] gratuitous-arp mac-change retransmit 3 interval 5

gratuitous-arp-learning enable

Use gratuitous-arp-learning enable to enable learning of gratuitous ARP packets.

Use undo gratuitous-arp-learning enable to disable learning of gratuitous ARP packets.

Syntax

gratuitous-arp-learning enable

undo gratuitous-arp-learning enable

Default

Learning of gratuitous ARP packets is enabled.

Views

System view

Predefined user roles

network-admin

mdc-admin

Usage guidelines

The learning of gratuitous ARP packets feature allows a device to maintain its ARP table by creating or updating ARP entries based on received gratuitous ARP packets.

When this feature is disabled, the device uses received gratuitous ARP packets to update existing ARP entries only. ARP entries are not created based on the received gratuitous ARP packets, which saves ARP table space.

Examples

# Enable learning of gratuitous ARP packets.

<Sysname> system-view

[Sysname] gratuitous-arp-learning enable

gratuitous-arp-sending enable

Use gratuitous-arp-sending enable to enable sending gratuitous ARP packets upon receiving ARP requests whose sender IP address is on a different subnet.

Use undo gratuitous-arp-sending enable to disable sending gratuitous ARP packets upon receiving ARP requests whose sender IP address is on a different subnet.

Syntax

gratuitous-arp-sending enable

undo gratuitous-arp-sending enable

Default

A device does not send gratuitous ARP packets when it receives ARP requests whose sender IP address is on a different subnet.

Views

System view

Predefined user roles

network-admin

mdc-admin

Examples

# Disable a device from sending gratuitous ARP packets upon receiving ARP requests whose sender IP address is on a different subnet.

<Sysname> system-view

[Sysname] undo gratuitous-arp-sending enable


Proxy ARP commands

display local-proxy-arp

Use display local-proxy-arp to display the local proxy ARP status.

Syntax

display local-proxy-arp [ interface interface-type interface-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

interface interface-type interface-number: Specifies an interface by its type and number. If you do not specify an interface, this command displays the local proxy ARP status for all interfaces.

Usage guidelines

You can use this command to check whether local proxy ARP is enabled or disabled.

Examples

# Display the local proxy ARP status for VLAN-interface 2.

<Sysname> display local-proxy-arp interface vlan-interface 2

Interface Vlan-interface2

 Local Proxy ARP status: enabled

Related commands

local-proxy-arp enable

display proxy-arp

Use display proxy-arp to display the proxy ARP status.

Syntax

display proxy-arp [ interface interface-type interface-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

interface interface-type interface-number: Specifies an interface by its type and number. If you do not specify an interface, this command displays the proxy ARP status for all interfaces.

Usage guidelines

You can use this command to check whether proxy ARP is enabled or disabled.

Examples

# Display the proxy ARP status on VLAN-interface 2.

<Sysname> display proxy-arp interface vlan-interface 2

Interface Vlan-interface2

 Proxy ARP status: disabled

Related commands

proxy-arp enable

local-proxy-arp enable

Use local-proxy-arp enable to enable local proxy ARP.

Use undo local-proxy-arp enable to disable local proxy ARP.

Syntax

local-proxy-arp enable [ ip-range start-ip-address to end-ip-address ]

undo local-proxy-arp enable

Default

Local proxy ARP is disabled.

Views

Layer 3 Ethernet interface view

Layer 3 Ethernet subinterface view

Layer 3 aggregate interface view

Layer 3 aggregate subinterface view

VLAN interface view

Predefined user roles

network-admin

mdc-admin

Parameters

ip-range start-ip-address to end-ip-address: Specifies the IP address range for which local proxy ARP is enabled. The start IP address must be lower than or equal to the end IP address.

Usage guidelines

Proxy ARP enables a device on a network to answer ARP requests for an IP address not on that network. With proxy ARP, hosts in different broadcast domains can communicate with each other as they do on the same network.

Proxy ARP includes common proxy ARP and local proxy ARP.

Common proxy ARP allows communication between hosts that connect to different Layer 3 interfaces and reside in different broadcast domains.

Local proxy ARP allows communication between hosts that connect to the same Layer 3 interface and reside in different broadcast domains.

If you execute this command multiple times, the most recent configuration takes effect.

Examples

# Enable local proxy ARP on VLAN-interface 2.

<Sysname> system-view

[Sysname] interface vlan-interface 2

[Sysname-Vlan-interface2] local-proxy-arp enable

# Enable local proxy ARP on VLAN-interface 2 for an IP address range.

<Sysname> system-view

[Sysname] interface vlan-interface 2

[Sysname-Vlan-interface2] local-proxy-arp enable ip-range 1.1.1.1 to 1.1.1.20

Related commands

display local-proxy-arp

proxy-arp enable

Use proxy-arp enable to enable proxy ARP.

Use undo proxy-arp enable to disable proxy ARP.

Syntax

proxy-arp enable

undo proxy-arp enable

Default

Proxy ARP is disabled.

Views

Layer 3 Ethernet interface view

Layer 3 Ethernet subinterface view

Layer 3 aggregate interface view

Layer 3 aggregate subinterface view

VLAN interface view

Predefined user roles

network-admin

mdc-admin

Usage guidelines

Proxy ARP enables a device on a network to answer ARP requests for an IP address not on that network. With proxy ARP, hosts in different broadcast domains can communicate with each other as they do on the same network.

Proxy ARP includes common proxy ARP and local proxy ARP.

Common proxy ARP allows communication between hosts that connect to different Layer 3 interfaces and reside in different broadcast domains.

Local proxy ARP allows communication between hosts that connect to the same Layer 3 interface and reside in different broadcast domains.

Examples

# Enable proxy ARP on VLAN-interface 2.

<Sysname> system-view

[Sysname] interface vlan-interface 2

[Sysname-Vlan-interface2] proxy-arp enable

Related commands

display proxy-arp


ARP snooping commands

arp snooping enable

Use arp snooping enable to enable ARP snooping.

Use undo arp snooping enable to disable ARP snooping.

Syntax

arp snooping enable

undo arp snooping enable

Default

ARP snooping is disabled.

Views

VLAN view

VSI view

Predefined user roles

network-admin

mdc-admin

Examples

# Enable ARP snooping for VLAN 2.

<Sysname> system-view

[Sysname] vlan 2

[Sysname-vlan2] arp snooping enable

# Enable ARP snooping for VSI vsi1.

<Sysname> system-view

[Sysname] vsi vsi1

[Sysname-vsi-vsi1] arp snooping enable

display arp snooping

Use display arp snooping to display ARP snooping entries.

Syntax

In standalone mode:

display arp snooping { vlan [ vlan-id ] | vsi [vsi-name ] } [ slot slot-number ] [ count ]

display arp snooping vlan ip ip-address [ slot slot-number ]

In IRF mode:

display arp snooping { vlan [ vlan-id ] | vsi [vsi-name ] } [ chassis chassis-number slot slot-number ] [ count ]

display arp snooping vlan ip ip-address [ chassis chassis-number slot slot-number ]

Views

Any view

Predefined user roles

network-admin

network-operator

mdc-admin

mdc-operator

Parameters

vlan: Displays ARP snooping entries for a VLAN.

vlan-id: Specifies a VLAN ID in the range of 1 to 4094. If you do not specify a VLAN, this command displays ARP snooping entries for all VLANs.

vsi: Displays ARP snooping entries for a VSI.

vsi-name: Specifies a VSI name, a case-sensitive string of 1 to 31 characters. If you do not specify a VSI, this command displays ARP snooping entries for all VSIs.

count: Displays the number of the ARP snooping entries. If you do not specify this keyword, the command displays ARP snooping entries.

ip ip-address: Displays the ARP snooping entry for the specified IP address in VLANs.

slot slot-number: Specifies a card by its slot number. If you do not specify a card, this command displays ARP snooping entries for the active MPU. (In standalone mode.)

chassis chassis-number slot slot-number: Specifies a card on an IRF member device. The chassis-number argument represents the member ID of the IRF member device. The slot-number argument represents the slot number of the card. If you do not specify a card, this command displays ARP snooping entries for the global active MPU. (In IRF mode.)

Examples

# Display ARP snooping entries for VLAN 2.

<Sysname> display arp snooping vlan 2

IP Address   MAC Address    VLAN ID Interface  Aging       Status

3.3.3.3         0003-0003-0003 2       XGE1/0/1   20          Valid

3.3.3.4         0004-0004-0004 2       XGE1/0/2   5           Invalid

# Display ARP snooping entries for all VSIs.

<Sysname> display arp snooping vsi

IP address      MAC address    VSI name                    Link ID    Aging(min)

1.1.1.2         000f-e201-0101 vsi1                        0x70000    14

1.1.1.3         000f-e201-0202 vsi1                        0x80000    18

1.1.1.4         000f-e201-0203 vsi2                        0x90000    10

# Display the ARP snooping entry for IP address 1.1.1.1 in a VLAN.

<Sysname> display arp snooping vlan ip 1.1.1.1

IP address      MAC address    VLAN ID Interface  Aging       Status

1.1.1.1         001f-e201-0111 2       GE1/0/1    15          Valid

# Display the number of ARP snooping entries in all VSIs.

<Sysname> display arp snooping vsi count

Total entries: 3

Table 4 Command output

Field

Description

IP Address

IP address in an ARP snooping entry.

MAC Address

MAC address in an ARP snooping entry.

VLAN ID

ID of the VLAN to which the ARP snooping entry belongs.

Interface

Input interface in an ARP snooping entry.

Aging

Aging time for an ARP snooping entry in minutes.

If the card learns an ARP snooping entry from another card, the card cannot learn the aging time of the entry, and this field displays N/A.

Status

Status of an ARP snooping entry: Valid, Invalid, Collision.

VSI name

Name of the VSI to which the ARP snooping entry belongs.

Link ID

Link ID in an ARP snooping entry.

Total entries

Number of ARP snooping entries.

 

Related commands

reset arp snooping

reset arp snooping

Use reset arp snooping to delete ARP snooping entries.

Syntax

reset arp snooping { vlan [ vlan-id ] | vsi [ vsi-name ] }

reset arp snooping vlan ip ip-address

Views

User view

Predefined user roles

network-admin

mdc-admin

Parameters

vlan: Deletes ARP snooping entries for a VLAN.

vlan-id: Specifies a VLAN ID in the range of 1 to 4094. If you do not specify a VLAN, this command deletes ARP snooping entries for all VLANs.

vsi: Deletes ARP snooping entries for a VSI.

vsi-name: Specifies a VSI name, a case-sensitive string of 1 to 31 characters. If you do not specify a VSI, this command deletes ARP snooping entries for all VSIs.

ip ip-address: Deletes the ARP snooping entry for the specified IP address in VLANs.

Examples

# Delete ARP snooping entries for VLAN 2.

<Sysname> reset arp snooping vlan 2

Related commands

display arp snooping


ARP fast-reply commands

arp fast-reply enable

Use arp fast-reply enable to enable ARP fast-reply for a VLAN.

Use undo arp fast-reply enable to disable ARP fast-reply for a VLAN.

Syntax

arp fast-reply enable

undo arp fast-reply enable

Default

ARP fast-reply is disabled on a VLAN.

Views

VLAN view

Predefined user roles

network-admin

mdc-admin

Examples

# Enable ARP fast-reply for VLAN 2.

<Sysname> system-view

[Sysname] vlan 2

[Sysname-vlan2] arp fast-reply enable


ARP direct route advertisement commands

arp route-direct advertise

Use arp route-direct advertise to enable ARP direct route advertisement.

Use undo arp route-direct advertise to disable ARP direct route advertisement.

Syntax

arp route-direct advertise

undo arp route-direct advertise

Default

ARP direct route advertisement is disabled.

Views

Interface view

Predefined user roles

network-admin

mdc-admin

Examples

# Enable ARP direct route advertisement on Layer 3 Ethernet interface Ten-GigabitEthernet 1/0/1.

<Sysname> system-view

[Sysname] interface ten-gigabitethernet 1/0/1

[Sysname-Ten-GigabitEthernet1/0/1] arp route-direct advertise


ARP proxy forwarding commands

arp proxy-forwarding

Use arp proxy-forwarding to enable the ARP proxy forwarding feature.

Use undo arp proxy-forwarding to disable ARP proxy forwarding.

Syntax

arp proxy-forwarding

undo arp proxy-forwarding

Default

ARP proxy forwarding is disabled.

Views

VLAN interface view

Predefined user roles

network-admin

mdc-admin

Examples

# Enable ARP proxy forwarding on VLAN-interface 10.

<Sysname> system-view

[Sysname] interface vlan-interface 10

[Sysname-Vlan-interface10] arp proxy-forwarding