H3C LSQM3MPUB0 Card Manual-6PW105

HomeSupportSwitchesS7500E SeriesInstall & UpgradeMPU Card ManualsH3C LSQM3MPUB0 Card Manual-6PW105
Download Book
  • Released At: 18-11-2019
  • Page Views:
  • Downloads:
Table of Contents
Related Documents

LSQM3MPUB0 management and route unit

1  Card identifier

The card identifier LSQM3MPUB0 is in the upper right corner of the front panel.

2  Specifications

 

IMPORTANT

IMPORTANT:

Before installing the card, you must remove the protection cover from the card to ensure correct installation.

 

Table 1 LSQM3MPUB0 specifications

Item

Specifications

Flash

1 GB

SDRAM (DDR3)

2 GB

Card size (H × W × D)

40 × 399 × 355 mm (1.57 × 15.71 × 13.98 in)

Power consumption

36 W to 60 W

Ports

·     1 console port

·     1 USB console port

·     2 network management ports: 1 × 10/100/1000BASE-T copper ports and 1 SFP fiber ports

·     1 USB port

Port speed

·     Console port: 115200 bps (default: 9600 bps)

·     USB console port: ≤ 115200 bps (default: 9600 bps)

·     10/100/1000BASE-T copper port: 10/100/1000 Mbps, half/full duplex

·     SFP fiber port: 1000 Mbps

Transmission medium and max transmission distance

·     Console port: 15 m (49.21 ft) over ordinary asynchronous serial port cables.

·     USB console port: 10 m (32.81 ft) over USB-AB cables

·     10/100/1000BASE-T copper port: 100 m (328.1 ft) over Category 5 or higher twisted pair cables

·     SFP fiber port: see Table 3

Compatible device models

S7506E (non-PoE).

Applicable host software versions

Version 7150 and later

 

 

NOTE:

·     To successfully connect an Ethernet port to a network management port (SFP port) on the card, make sure the Ethernet port is operating in full duplex mode and at the port speed of 1000 Mbps.

·     H3C recommends not using a USB extender cable to connect the USB port.

 

The 10/100/1000BASE-T copper port uses an RJ-45 connector.

Figure 1 RJ-45 connector

 

Table 2 RJ-45 GE connector pinout

Pin

10BASE-T/100BASE-TX/1000BASE-T

Signal

Function

1

MX_0+

Transmits and receives data.

2

MX_0-

Transmits and receives data.

3

MX_1+

Transmits and receives data.

4

MX_2+

Transmits and receives data.

5

MX_2-

Transmits and receives data.

6

MX_1-

Transmits and receives data.

7

MX_3+

Transmits and receives data.

8

MX_3-

Transmits and receives data.

 

Table 3 describes the SFP transceiver modules available for the SFP ports on the card.

Table 3 SFP transceiver module specifications

Module

Central wavelength

Connector type

Cable specifications

Maximum transmission distance

SFP-GE-SX-MM850-A

850 nm

LC

50/125 μm multi-mode optical fiber

550 m (0.34 miles)

850 nm

LC

62.5/125 μm multi-mode optical fiber

275 m (0.17 miles)

SFP-GE-SX-MM850-D

850 nm

LC

50/125 μm multi-mode optical fiber

550 m (0.34 miles)

850 nm

LC

62.5/125 μm multi-mode optical fiber

275 m (0.17 miles)

SFP-GE-LX-SM1310-A

1310 nm

LC

9/125 μm single-mode optical fiber

10 km (6.21 miles)

1310 nm

LC

50/125 μm multi-mode optical fiber

550 m (1804.46 ft)

1310 nm

LC

62.5/125 μm multi-mode optical fiber

550 m (1804.46 ft)

SFP-GE-LX-SM1310-D

1310 nm

LC

9/125 μm single-mode optical fiber

10 km (6.21 miles)

1310 nm

LC

50/125 μm multi-mode optical fiber

550 m (1804.46 ft)

1310 nm

LC

62.5/125 μm multi-mode optical fiber

550 m (1804.46 ft)

SFP-GE-LH40-SM1310

1310 nm

LC

9/125 μm single-mode optical fiber

40 km (24.86 miles)

SFP-GE-LH40-SM1310-D

1310nm

LC

9/125 μm single-mode optical fiber

40 km (24.86 miles)

SFP-GE-LH40-SM1550

1550 nm

LC

9/125 μm single-mode optical fiber

40 km (24.86 miles)

SFP-GE-LH80-SM1550

1550 nm

LC

9/125 μm single-mode optical fiber

70 km (43.50 miles)

SFP-GE-LH80-SM1550-D

1550nm

LC

9/125 μm single-mode optical fiber

70 km (43.50 miles)

SFP-GE-LH100-SM1550

1550 nm

LC

9/125 μm single-mode optical fiber

100 km (62.14 miles)

SFP-GE-LX-SM1310-BIDI

RX: 1490 nm

TX: 1310 nm

LC

9/125 μm single-mode optical fiber

10 km (6.21 miles)

SFP-GE-LX-SM1490-BIDI

RX: 1310 nm

TX: 1490 nm

LC

9/125 μm single-mode optical fiber

10 km (6.21 miles)

 

 

NOTE:

·     BIDI modules use different central wavelengths in transmit and receive directions, in order to implement bidirectional transmission of optical signals over the same fiber.

·     The BIDI modules must be used in pairs. For example, if you install the SFP-GE-LX-SM1310-BIDI in the local port, you must install the SFP-GE-LX-SM1490-BIDI in the peer port.

 

3  Related documentation

For module installation, see H3C S7500E Switch Series Installation Guide.

For software upgrade, see the release notes for the device.

 

 

Copyright © 2014-2018 New H3C Technologies Co ., Ltd.

The information in this document is subject to change without notice.

  • Cloud & AI
  • InterConnect
  • Intelligent Computing
  • Security
  • SMB Products
  • Intelligent Terminal Products
  • Product Support Services
  • Technical Service Solutions
All Services
  • Resource Center
  • Policy
  • Online Help
All Support
  • Become a Partner
  • Partner Resources
  • Partner Business Management
All Partners
  • Profile
  • News & Events
  • Online Exhibition Center
  • Contact Us
All About Us
新华三官网