H3C S6890 System Log Messages Reference(27xx)-6W100

HomeSupportResource CenterSwitchesH3C S6890 Switch SeriesH3C S6890 Switch SeriesTechnical DocumentsMaintainMessage ReferencesH3C S6890 System Log Messages Reference(27xx)-6W100
Download Book
Table of Contents
Related Documents

 

H3C S6890 Switch Series

System Log Messages Reference

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Document version: 6W100-20190610

 

Copyright © 2019 New H3C Technologies Co., Ltd. All rights reserved.

No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of New H3C Technologies Co., Ltd.

Except for the trademarks of New H3C Technologies Co., Ltd., any trademarks that may be mentioned in this document are the property of their respective owners.

The information in this document is subject to change without notice.


 

Contents

Introduction· 1

System log message format 1

Managing and obtaining system log messages· 3

Obtaining log messages from the console terminal 3

Obtaining log messages from the log buffer 3

Obtaining log messages from a monitor terminal 3

Obtaining log messages from the log file· 3

Obtaining log messages from a log host 4

Software module list 4

Using this document 7

AAA messages· 9

AAA_FAILURE· 9

AAA_LAUNCH· 9

AAA_SUCCESS· 10

ACL messages· 10

ACL_ACCELERATE_NO_RES· 10

ACL_ACCELERATE_NONCONTIGUOUSMASK· 11

ACL_ACCELERATE_NOT_SUPPORT· 11

ACL_ACCELERATE_NOT_SUPPORTHOPBYHOP· 11

ACL_ACCELERATE_NOT_SUPPORTMULTITCPFLAG·· 12

ACL_ACCELERATE_UNK_ERR· 12

ACL_IPV6_STATIS_INFO·· 12

ACL_NO_MEM·· 13

ACL_STATIS_INFO·· 13

ANCP messages· 13

ANCP_INVALID_PACKET· 14

ARP messages· 14

ARP_ACTIVE_ACK_NO_REPLY· 14

ARP_ACTIVE_ACK_NOREQUESTED_REPLY· 15

ARP_BINDRULETOHW_FAILED·· 15

ARP_DETECTION_LOG·· 16

ARP_DUPLICATE_IPADDR_DETECT· 16

ARP_DYNAMIC· 17

ARP_DYNAMIC_IF· 17

ARP_DYNAMIC_SLOT· 18

ARP_ENTRY_CONFLICT· 19

ARP_HOST_IP_CONFLICT· 19

ARP_MAXIMUM_DEVICE· 20

ARP_RATE_EXCEEDED·· 20

ARP_SENDER_IP_INVALID·· 20

ARP_SENDER_MAC_INVALID·· 21

ARP_SENDER_SMACCONFLICT· 21

ARP_SENDER_SMACCONFLICT_VSI 22

ARP_SRC_MAC_FOUND_ATTACK· 22

ARP_SUP_ENABLE_FAILED·· 23

ARP_TARGET_IP_INVALID·· 23

ARP_THRESHOLD_REACHED·· 23

DUPIFIP· 24

DUPIP· 24

DUPVRRPIP· 24

ATK messages· 25

ATK_ICMP_ADDRMASK_REQ·· 25

ATK_ICMP_ADDRMASK_REQ_RAW·· 26

ATK_ICMP_ADDRMASK_REQ_RAW_SZ· 27

ATK_ICMP_ADDRMASK_REQ_SZ· 28

ATK_ICMP_ADDRMASK_RPL· 29

ATK_ICMP_ADDRMASK_RPL_RAW·· 30

ATK_ICMP_ADDRMASK_RPL_RAW_SZ· 31

ATK_ICMP_ADDRMASK_RPL_SZ· 32

ATK_ICMP_ECHO_REQ·· 33

ATK_ICMP_ECHO_REQ_RAW·· 34

ATK_ICMP_ECHO_REQ_RAW_SZ· 35

ATK_ICMP_ECHO_REQ_SZ· 36

ATK_ICMP_ECHO_RPL· 37

ATK_ICMP_ECHO_RPL_RAW·· 38

ATK_ICMP_ECHO_RPL_RAW_SZ· 39

ATK_ICMP_ECHO_RPL_SZ· 40

ATK_ICMP_FLOOD·· 41

ATK_ICMP_FLOOD_SZ· 41

ATK_ICMP_INFO_REQ·· 42

ATK_ICMP_INFO_REQ_RAW·· 43

ATK_ICMP_INFO_REQ_RAW_SZ· 44

ATK_ICMP_INFO_REQ_SZ· 45

ATK_ICMP_INFO_RPL· 46

ATK_ICMP_INFO_RPL_RAW·· 47

ATK_ICMP_INFO_RPL_RAW_SZ· 48

ATK_ICMP_INFO_RPL_SZ· 49

ATK_ICMP_LARGE· 50

ATK_ICMP_LARGE_RAW·· 51

ATK_ICMP_LARGE_RAW_SZ· 51

ATK_ICMP_LARGE_SZ· 52

ATK_ICMP_PARAPROBLEM·· 53

ATK_ICMP_PARAPROBLEM_RAW·· 54

ATK_ICMP_PARAPROBLEM_RAW_SZ· 55

ATK_ICMP_PARAPROBLEM_SZ· 56

ATK_ICMP_PINGOFDEATH· 57

ATK_ICMP_PINGOFDEATH_RAW·· 58

ATK_ICMP_PINGOFDEATH_RAW_SZ· 58

ATK_ICMP_PINGOFDEATH_SZ· 59

ATK_ICMP_REDIRECT· 60

ATK_ICMP_REDIRECT_RAW·· 61

ATK_ICMP_REDIRECT_RAW_SZ· 62

ATK_ICMP_REDIRECT_SZ· 63

ATK_ICMP_SMURF· 64

ATK_ICMP_SMURF_RAW·· 65

ATK_ICMP_SMURF_RAW_SZ· 66

ATK_ICMP_SMURF_SZ· 67

ATK_ICMP_SOURCEQUENCH· 68

ATK_ICMP_SOURCEQUENCH_RAW·· 69

ATK_ICMP_SOURCEQUENCH_RAW_SZ· 70

ATK_ICMP_SOURCEQUENCH_SZ· 71

ATK_ICMP_TIMEEXCEED·· 72

ATK_ICMP_TIMEEXCEED_RAW·· 73

ATK_ICMP_TIMEEXCEED_RAW_SZ· 74

ATK_ICMP_TIMEEXCEED_SZ· 75

ATK_ICMP_TRACEROUTE· 76

ATK_ICMP_TRACEROUTE_RAW·· 77

ATK_ICMP_TRACEROUTE_RAW_SZ· 77

ATK_ICMP_TRACEROUTE_SZ· 78

ATK_ICMP_TSTAMP_REQ·· 79

ATK_ICMP_TSTAMP_REQ_RAW·· 80

ATK_ICMP_TSTAMP_REQ_RAW_SZ· 81

ATK_ICMP_TSTAMP_REQ_SZ· 82

ATK_ICMP_TSTAMP_RPL· 83

ATK_ICMP_TSTAMP_RPL_RAW·· 84

ATK_ICMP_TSTAMP_RPL_RAW_SZ· 85

ATK_ICMP_TSTAMP_RPL_SZ· 86

ATK_ICMP_TYPE· 87

ATK_ICMP_TYPE_RAW·· 88

ATK_ICMP_TYPE_RAW_SZ· 89

ATK_ICMP_TYPE_SZ· 90

ATK_ICMP_UNREACHABLE· 91

ATK_ICMP_UNREACHABLE_RAW·· 92

ATK_ICMP_UNREACHABLE_RAW_SZ· 93

ATK_ICMP_UNREACHABLE_SZ· 94

ATK_ICMPV6_DEST_UNREACH· 95

ATK_ICMPV6_DEST_UNREACH_RAW·· 96

ATK_ICMPV6_DEST_UNREACH_RAW_SZ· 96

ATK_ICMPV6_DEST_UNREACH_SZ· 97

ATK_ICMPV6_ECHO_REQ·· 98

ATK_ICMPV6_ECHO_REQ_RAW·· 99

ATK_ICMPV6_ECHO_REQ_RAW_SZ· 99

ATK_ICMPV6_ECHO_REQ_SZ· 100

ATK_ICMPV6_ECHO_RPL· 101

ATK_ICMPV6_ECHO_RPL_RAW·· 102

ATK_ICMPV6_ECHO_RPL_RAW_SZ· 102

ATK_ICMPV6_ECHO_RPL_SZ· 103

ATK_ICMPV6_FLOOD·· 104

ATK_ICMPV6_FLOOD_SZ· 104

ATK_ICMPV6_GROUPQUERY· 105

ATK_ICMPV6_GROUPQUERY_RAW·· 106

ATK_ICMPV6_GROUPQUERY_RAW_SZ· 106

ATK_ICMPV6_GROUPQUERY_SZ· 107

ATK_ICMPV6_GROUPREDUCTION· 108

ATK_ICMPV6_GROUPREDUCTION_RAW·· 109

ATK_ICMPV6_GROUPREDUCTION_RAW_SZ· 109

ATK_ICMPV6_GROUPREDUCTION_SZ· 110

ATK_ICMPV6_GROUPREPORT· 111

ATK_ICMPV6_GROUPREPORT_RAW·· 112

ATK_ICMPV6_GROUPREPORT_RAW_SZ· 112

ATK_ICMPV6_GROUPREPORT_SZ· 113

ATK_ICMPV6_LARGE· 114

ATK_ICMPV6_LARGE_RAW·· 114

ATK_ICMPV6_LARGE_RAW_SZ· 115

ATK_ICMPV6_LARGE_SZ· 115

ATK_ICMPV6_PACKETTOOBIG·· 116

ATK_ICMPV6_PACKETTOOBIG_RAW·· 117

ATK_ICMPV6_PACKETTOOBIG_RAW_SZ· 117

ATK_ICMPV6_PACKETTOOBIG_SZ· 118

ATK_ICMPV6_PARAPROBLEM·· 119

ATK_ICMPV6_PARAPROBLEM_RAW·· 120

ATK_ICMPV6_PARAPROBLEM_RAW_SZ· 120

ATK_ICMPV6_PARAPROBLEM_SZ· 121

ATK_ICMPV6_TIMEEXCEED·· 122

ATK_ICMPV6_TIMEEXCEED_RAW·· 123

ATK_ICMPV6_TIMEEXCEED_RAW_SZ· 123

ATK_ICMPV6_TIMEEXCEED_SZ· 124

ATK_ICMPV6_TRACEROUTE· 125

ATK_ICMPV6_TRACEROUTE_RAW·· 126

ATK_ICMPV6_TRACEROUTE_RAW_SZ· 127

ATK_ICMPV6_TRACEROUTE_SZ· 128

ATK_ICMPV6_TYPE· 129

ATK_ICMPV6_TYPE _RAW_SZ· 130

ATK_ICMPV6_TYPE_RAW·· 130

ATK_ICMPV6_TYPE_SZ· 131

ATK_IP_OPTION· 132

ATK_IP_OPTION_RAW·· 133

ATK_IP_OPTION_RAW_SZ· 134

ATK_IP_OPTION_SZ· 135

ATK_IP4_ACK_FLOOD·· 136

ATK_IP4_ACK_FLOOD_SZ· 136

ATK_IP4_DIS_PORTSCAN· 137

ATK_IP4_DIS_PORTSCAN_SZ· 137

ATK_IP4_DNS_FLOOD·· 138

ATK_IP4_DNS_FLOOD_SZ· 138

ATK_IP4_FIN_FLOOD·· 139

ATK_IP4_FIN_FLOOD_SZ· 139

ATK_IP4_FRAGMENT· 140

ATK_IP4_FRAGMENT_RAW·· 141

ATK_IP4_FRAGMENT_RAW_SZ· 142

ATK_IP4_FRAGMENT_SZ· 143

ATK_IP4_HTTP_FLOOD·· 144

ATK_IP4_HTTP_FLOOD_SZ· 144

ATK_IP4_IMPOSSIBLE· 145

ATK_IP4_IMPOSSIBLE_RAW·· 146

ATK_IP4_IMPOSSIBLE_RAW_SZ· 147

ATK_IP4_IMPOSSIBLE_SZ· 148

ATK_IP4_IPSWEEP· 149

ATK_IP4_IPSWEEP_SZ· 149

ATK_IP4_PORTSCAN· 150

ATK_IP4_PORTSCAN_SZ· 150

ATK_IP4_RST_FLOOD·· 151

ATK_IP4_RST_FLOOD_SZ· 151

ATK_IP4_SYN_FLOOD·· 152

ATK_IP4_SYN_FLOOD_SZ· 152

ATK_IP4_SYNACK_FLOOD·· 153

ATK_IP4_SYNACK_FLOOD_SZ· 153

ATK_IP4_TCP_ALLFLAGS· 154

ATK_IP4_TCP_ALLFLAGS_RAW·· 155

ATK_IP4_TCP_ALLFLAGS_RAW_SZ· 155

ATK_IP4_TCP_ALLFLAGS_SZ· 156

ATK_IP4_TCP_FINONLY· 157

ATK_IP4_TCP_FINONLY_RAW·· 158

ATK_IP4_TCP_FINONLY_RAW_SZ· 158

ATK_IP4_TCP_FINONLY_SZ· 159

ATK_IP4_TCP_INVALIDFLAGS· 160

ATK_IP4_TCP_INVALIDFLAGS_RAW·· 161

ATK_IP4_TCP_INVALIDFLAGS_RAW_SZ· 162

ATK_IP4_TCP_INVALIDFLAGS_SZ· 163

ATK_IP4_TCP_LAND·· 164

ATK_IP4_TCP_LAND_RAW·· 165

ATK_IP4_TCP_LAND_RAW_SZ· 165

ATK_IP4_TCP_LAND_SZ· 166

ATK_IP4_TCP_NULLFLAG·· 167

ATK_IP4_TCP_NULLFLAG_RAW·· 168

ATK_IP4_TCP_NULLFLAG_RAW_SZ· 168

ATK_IP4_TCP_NULLFLAG_SZ· 169

ATK_IP4_TCP_SYNFIN· 170

ATK_IP4_TCP_SYNFIN_RAW·· 171

ATK_IP4_TCP_SYNFIN_RAW_SZ· 171

ATK_IP4_TCP_SYNFIN_SZ· 172

ATK_IP4_TCP_WINNUKE· 173

ATK_IP4_TCP_WINNUKE_RAW·· 174

ATK_IP4_TCP_WINNUKE_RAW_SZ· 174

ATK_IP4_TCP_WINNUKE_SZ· 175

ATK_IP4_TEARDROP· 176

ATK_IP4_TEARDROP_RAW·· 177

ATK_IP4_TEARDROP_RAW_SZ· 178

ATK_IP4_TEARDROP_SZ· 179

ATK_IP4_TINY_FRAGMENT· 180

ATK_IP4_TINY_FRAGMENT_RAW·· 181

ATK_IP4_TINY_FRAGMENT_RAW_SZ· 182

ATK_IP4_TINY_FRAGMENT_SZ· 183

ATK_IP4_UDP_BOMB· 184

ATK_IP4_UDP_BOMB_RAW·· 185

ATK_IP4_UDP_BOMB_RAW_SZ· 186

ATK_IP4_UDP_BOMB_SZ· 187

ATK_IP4_UDP_FLOOD·· 188

ATK_IP4_UDP_FLOOD_SZ· 188

ATK_IP4_UDP_FRAGGLE· 189

ATK_IP4_UDP_FRAGGLE_RAW·· 190

ATK_IP4_UDP_FRAGGLE_RAW_SZ· 190

ATK_IP4_UDP_FRAGGLE_SZ· 191

ATK_IP4_UDP_SNORK· 192

ATK_IP4_UDP_SNORK_RAW·· 193

ATK_IP4_UDP_SNORK_RAW_SZ· 193

ATK_IP4_UDP_SNORK_SZ· 194

ATK_IP6_ACK_FLOOD·· 195

ATK_IP6_ACK_FLOOD_SZ· 195

ATK_IP6_DIS_PORTSCAN· 196

ATK_IP6_DIS_PORTSCAN_SZ· 196

ATK_IP6_DNS_FLOOD·· 197

ATK_IP6_DNS_FLOOD_SZ· 197

ATK_IP6_FIN_FLOOD·· 198

ATK_IP6_FIN_FLOOD_SZ· 198

ATK_IP6_FRAGMENT· 199

ATK_IP6_FRAGMENT_RAW·· 200

ATK_IP6_FRAGMENT_RAW_SZ· 200

ATK_IP6_FRAGMENT_SZ· 201

ATK_IP6_HTTP_FLOOD·· 202

ATK_IP6_HTTP_FLOOD_SZ· 202

ATK_IP6_IMPOSSIBLE· 203

ATK_IP6_IMPOSSIBLE_RAW·· 204

ATK_IP6_IMPOSSIBLE_RAW_SZ· 204

ATK_IP6_IMPOSSIBLE_SZ· 205

ATK_IP6_IPSWEEP· 205

ATK_IP6_IPSWEEP_SZ· 206

ATK_IP6_PORTSCAN· 206

ATK_IP6_PORTSCAN_SZ· 207

ATK_IP6_RST_FLOOD·· 207

ATK_IP6_RST_FLOOD_SZ· 208

ATK_IP6_SYN_FLOOD·· 208

ATK_IP6_SYN_FLOOD_SZ· 209

ATK_IP6_SYNACK_FLOOD·· 209

ATK_IP6_SYNACK_FLOOD_SZ· 210

ATK_IP6_TCP_ALLFLAGS· 210

ATK_IP6_TCP_ALLFLAGS_RAW·· 211

ATK_IP6_TCP_ALLFLAGS_RAW_SZ· 211

ATK_IP6_TCP_ALLFLAGS_SZ· 212

ATK_IP6_TCP_FINONLY· 213

ATK_IP6_TCP_FINONLY_RAW·· 213

ATK_IP6_TCP_FINONLY_RAW_SZ· 214

ATK_IP6_TCP_FINONLY_SZ· 214

ATK_IP6_TCP_INVALIDFLAGS· 215

ATK_IP6_TCP_INVALIDFLAGS_RAW·· 216

ATK_IP6_TCP_INVALIDFLAGS_RAW_SZ· 217

ATK_IP6_TCP_INVALIDFLAGS_SZ· 218

ATK_IP6_TCP_LAND·· 219

ATK_IP6_TCP_LAND_RAW·· 219

ATK_IP6_TCP_LAND_RAW_SZ· 220

ATK_IP6_TCP_LAND_SZ· 220

ATK_IP6_TCP_NULLFLAG·· 221

ATK_IP6_TCP_NULLFLAG_RAW·· 221

ATK_IP6_TCP_NULLFLAG_RAW_SZ· 222

ATK_IP6_TCP_NULLFLAG_SZ· 222

ATK_IP6_TCP_SYNFIN· 223

ATK_IP6_TCP_SYNFIN_RAW·· 223

ATK_IP6_TCP_SYNFIN_RAW_SZ· 224

ATK_IP6_TCP_SYNFIN_SZ· 224

ATK_IP6_TCP_WINNUKE· 225

ATK_IP6_TCP_WINNUKE_RAW·· 225

ATK_IP6_TCP_WINNUKE_RAW_SZ· 226

ATK_IP6_TCP_WINNUKE_SZ· 226

ATK_IP6_UDP_FLOOD·· 227

ATK_IP6_UDP_FLOOD_SZ· 227

ATK_IP6_UDP_FRAGGLE· 228

ATK_IP6_UDP_FRAGGLE_RAW·· 228

ATK_IP6_UDP_FRAGGLE_RAW_SZ· 229

ATK_IP6_UDP_FRAGGLE_SZ· 229

ATK_IP6_UDP_SNORK· 230

ATK_IP6_UDP_SNORK_RAW·· 230

ATK_IP6_UDP_SNORK_RAW_SZ· 231

ATK_IP6_UDP_SNORK_SZ· 231

ATK_IPOPT_ABNORMAL· 232

ATK_IPOPT_ABNORMAL_RAW·· 233

ATK_IPOPT_ABNORMAL_RAW_SZ· 234

ATK_IPOPT_ABNORMAL_SZ· 235

ATK_IPOPT_LOOSESRCROUTE· 236

ATK_IPOPT_LOOSESRCROUTE_RAW·· 237

ATK_IPOPT_LOOSESRCROUTE_RAW_SZ· 238

ATK_IPOPT_LOOSESRCROUTE_SZ· 239

ATK_IPOPT_RECORDROUTE· 240

ATK_IPOPT_RECORDROUTE_RAW·· 241

ATK_IPOPT_RECORDROUTE_RAW_SZ· 242

ATK_IPOPT_RECORDROUTE_SZ· 243

ATK_IPOPT_ROUTEALERT· 244

ATK_IPOPT_ROUTEALERT_RAW·· 245

ATK_IPOPT_ROUTEALERT_RAW_SZ· 246

ATK_IPOPT_ROUTEALERT_SZ· 247

ATK_IPOPT_SECURITY· 248

ATK_IPOPT_SECURITY_RAW·· 249

ATK_IPOPT_SECURITY_RAW_SZ· 250

ATK_IPOPT_SECURITY_SZ· 251

ATK_IPOPT_STREAMID·· 252

ATK_IPOPT_STREAMID_RAW·· 253

ATK_IPOPT_STREAMID_RAW_SZ· 254

ATK_IPOPT_STREAMID_SZ· 255

ATK_IPOPT_STRICTSRCROUTE· 256

ATK_IPOPT_STRICTSRCROUTE_RAW·· 257

ATK_IPOPT_STRICTSRCROUTE_RAW_SZ· 258

ATK_IPOPT_STRICTSRCROUTE_SZ· 259

ATK_IPOPT_TIMESTAMP· 260

ATK_IPOPT_TIMESTAMP_RAW·· 261

ATK_IPOPT_TIMESTAMP_RAW_SZ· 262

ATK_IPOPT_TIMESTAMP_SZ· 263

ATK_IPV6_EXT_HEADER· 264

ATK_IPV6_EXT_HEADER_RAW·· 265

ATK_IPV6_EXT_HEADER_RAW_SZ· 265

ATK_IPV6_EXT_HEADER_SZ· 266

BFD messages· 266

BFD_CHANGE_FSM·· 267

BFD_REACHED_UPPER_LIMIT· 267

BGP messages· 267

BGP_EXCEED_ROUTE_LIMIT· 268

BGP_REACHED_THRESHOLD·· 268

BGP_LOG_ROUTE_FLAP· 269

BGP_MEM_ALERT· 269

BGP_PEER_LICENSE_REACHED·· 269

BGP_ROUTE_LICENSE_REACHED·· 270

BGP_STATE_CHANGED·· 270

BLS messages· 270

BLS_ENTRY_ADD·· 271

BLS_ENTRY_DEL· 271

BLS_IPV6_ENTRY_ADD·· 272

BLS_IPV6_ENTRY_DEL· 272

CFD messages· 272

CFD_CROSS_CCM·· 273

CFD_ERROR_CCM·· 273

CFD_LOST_CCM·· 274

CFD_RECEIVE_CCM·· 274

CFGMAN messages· 275

CFGMAN_ARCHIVE_SCP_FAIL· 275

CFGMAN_CFGCHANGED·· 275

CFGMAN_EXIT_FROM_CONFIGURE· 276

CFGMAN_OPTCOMPLETION· 276

CONNLMT messages· 277

CONNLMT_IPV4_OVERLOAD·· 278

CONNLMT_IPV4_RECOVER· 279

CONNLMT_IPV6_OVERLOAD·· 280

CONNLMT_IPV6_RECOVER· 281

DEV messages· 281

BOARD_INSERTED·· 282

BOARD_REBOOT· 282

BOARD_REMOVED·· 283

BOARD_STATE_FAULT· 284

BOARD_STATE_NORMAL· 284

BOARD_STATE_STARTING·· 285

CFCARD_INSERTED·· 285

CFCARD_REMOVED·· 286

CHASSIS_REBOOT· 286

DEV_CLOCK_CHANGE· 287

DEV_FAULT_TOOLONG·· 287

DYINGGASP· 287

FAN_ABSENT· 288

FAN_DIRECTION_NOT_PREFERRED·· 288

FAN_FAILED·· 289

FAN_RECOVERED·· 289

MAD_DETECT· 290

POWER_ABSENT· 290

POWER_FAILED·· 291

POWER_MONITOR_ABSENT· 291

POWER_MONITOR_FAILED·· 292

POWER_MONITOR_RECOVERED·· 292

POWER_RECOVERED·· 293

RPS_ABSENT· 293

RPS_NORMAL· 294

SUBCARD_FAULT· 295

SUBCARD_INSERTED·· 296

SUBCARD_REBOOT· 297

SUBCARD_REMOVED·· 298

SYSTEM_REBOOT· 298

TEMPERATURE_ALARM·· 299

TEMPERATURE_LOW·· 300

TEMPERATURE_NORMAL· 301

TEMPERATURE_SHUTDOWN· 302

TEMPERATURE_WARNING·· 303

VCHK_VERSION_INCOMPATIBLE· 304

DHCP· 304

DHCP_NOTSUPPORTED·· 304

DHCP_NORESOURCES· 305

DHCPR·· 305

DHCPR_SERVERCHANGE· 305

DHCPR_SWITCHMASTER· 306

DHCPS messages· 306

DHCPS_ALLOCATE_IP· 306

DHCPS_CONFLICT_IP· 307

DHCPS_EXTEND_IP· 307

DHCPS_FILE· 307

DHCPS_RECLAIM_IP· 308

DHCPS_VERIFY_CLASS· 308

DHCPS6 messages· 308

DHCPS6_ALLOCATE_ADDRESS· 309

DHCPS6_ALLOCATE_PREFIX· 309

DHCPS6_CONFLICT_ADDRESS· 310

DHCPS6_EXTEND_ADDRESS· 310

DHCPS6_EXTEND_PREFIX· 311

DHCPS6_FILE· 311

DHCPS6_RECLAIM_ADDRESS· 312

DHCPS6_RECLAIM_PREFIX· 312

DHCPSP4· 312

DHCPSP4_FILE· 313

DHCPSP6· 313

DHCPSP6_FILE· 313

DIAG messages· 313

CPU_MINOR_RECOVERY· 314

CPU_MINOR_THRESHOLD·· 314

CPU_SEVERE_RECOVERY· 314

CPU_SEVERE_THRESHOLD·· 315

MEM_ALERT· 316

MEM_BELOW_THRESHOLD·· 317

MEM_EXCEED_THRESHOLD·· 318

DLDP messages· 318

DLDP_AUTHENTICATION_FAILED·· 318

DLDP_LINK_BIDIRECTIONAL· 319

DLDP_LINK_SHUTMODECHG·· 319

DLDP_LINK_UNIDIRECTIONAL· 320

DLDP_NEIGHBOR_AGED·· 320

DLDP_NEIGHBOR_CONFIRMED·· 321

DLDP_NEIGHBOR_DELETED·· 321

DOT1X messages· 321

DOT1X_CONFIG_NOTSUPPORT· 322

DOT1X_LOGIN_FAILURE· 322

DOT1X_LOGIN_SUCC· 323

DOT1X_LOGIN_SUCC (in open mode) 323

DOT1X_LOGOFF· 324

DOT1X_LOGOFF (in open mode) 324

DOT1X_LOGOFF_ABNORMAL· 325

DOT1X_LOGOFF_ABNORMAL (in open mode) 325

DOT1X_MACBINDING_EXIST· 326

DOT1X_NOTENOUGH_EADFREEIP_RES· 326

DOT1X_NOTENOUGH_EADFREERULE_RES· 327

DOT1X_NOTENOUGH_EADMACREDIR_RES· 327

DOT1X_NOTENOUGH_EADPORTREDIR_RES· 327

DOT1X_NOTENOUGH_ENABLEDOT1X_RES· 328

DOT1X_SMARTON_FAILURE· 328

DOT1X_UNICAST_NOT_EFFECTIVE· 328

DRNI 329

DRNI_IFEVENT_DR_BIND·· 329

DRNI_IFEVENT_DR_GLOBALDOWN· 329

DRNI_IFEVENT_DR_GLOBALUP· 329

DRNI_IFEVENT_DR_NOSELECTED·· 330

DRNI_IFEVENT_DR_PEER_NOSELECTED·· 330

DRNI_IFEVENT_DR_PEER_SELECTED·· 330

DRNI_IFEVENT_DR_SELECTED·· 331

DRNI_IFEVENT_DR_UNBIND·· 331

DRNI_IFEVENT_IPP_BIND·· 331

DRNI_IFEVENT_IPP_DOWN· 332

DRNI_IFEVENT_IPP_UNBIND·· 332

DRNI_IFEVENT_IPP_UP· 332

DRNI_IPP_BLOCK· 333

DRNI_IPP_UNBLOCK· 333

DRNI_KEEPALIVEINTERVAL_MISMATCH· 333

DRNI_KEEPALIVELINK_DOWN· 334

DRNI_KEEPALIVELINK_UP· 334

DRNI_SECONDARY_MADDOWN· 334

DRNI_SYSEVENT_DEVICEROLE_CHANGE· 335

DRNI_SYSEVENT_MAC_CHANGE· 335

DRNI_SYSEVENT_NUMBER_CHANGE· 335

DRNI_SYSEVENT_PRIORITY_CHANGE· 336

EDEV messages· 336

EDEV_ALARM_IN_REMOVED·· 336

EDEV_ALARM_IN_REPORTEDOCCURRED·· 336

EDEV_FAILOVER_GROUP_STATE_CHANGE· 337

ERPS messages· 337

ERPS_STATE_CHANGED·· 337

ETHOAM messages· 337

ETHOAM_CONNECTION_FAIL_DOWN· 338

ETHOAM_CONNECTION_FAIL_TIMEOUT· 338

ETHOAM_CONNECTION_FAIL_UNSATISF· 338

ETHOAM_CONNECTION_SUCCEED·· 339

ETHOAM_DISABLE· 339

ETHOAM_DISCOVERY_EXIT· 339

ETHOAM_ENABLE· 340

ETHOAM_ENTER_LOOPBACK_CTRLLED·· 340

ETHOAM_ENTER_LOOPBACK_CTRLLING·· 340

ETHOAM_LOCAL_DYING_GASP· 341

ETHOAM_LOCAL_ERROR_FRAME· 341

ETHOAM_LOCAL_ERROR_FRAME_PERIOD·· 341

ETHOAM_LOCAL_ERROR_FRAME_SECOND·· 342

ETHOAM_LOCAL_ERROR_SYMBOL· 342

ETHOAM_LOCAL_LINK_FAULT· 342

ETHOAM_LOOPBACK_EXIT· 343

ETHOAM_LOOPBACK_EXIT_ERROR_STATU· 343

ETHOAM_LOOPBACK_NO_RESOURCE· 343

ETHOAM_LOOPBACK_NOT_SUPPORT· 344

ETHOAM_QUIT_LOOPBACK_CTRLLED·· 344

ETHOAM_QUIT_LOOPBACK_CTRLLING·· 344

ETHOAM_REMOTE_CRITICAL· 345

ETHOAM_REMOTE_DYING_GASP· 345

ETHOAM_REMOTE_ERROR_FRAME· 345

ETHOAM_REMOTE_ERROR_FRAME_PERIOD·· 346

ETHOAM_REMOTE_ERROR_FRAME_SECOND·· 346

ETHOAM_REMOTE_ERROR_SYMBOL· 346

ETHOAM_REMOTE_EXIT· 347

ETHOAM_REMOTE_FAILURE_RECOVER· 347

ETHOAM_REMOTE_LINK_FAULT· 347

ETHOAM_NO_ENOUGH_RESOURCE· 348

ETHOAM_NOT_CONNECTION_TIMEOUT· 348

EVB messages· 348

EVB_AGG_FAILED·· 349

EVB_LICENSE_EXPIRE· 349

EVB_VSI_OFFLINE· 349

EVB_VSI_ONLINE· 350

EVIISIS messages· 350

EVIISIS_LICENSE_EXPIRED·· 350

EVIISIS_LICENSE_EXPIRED_TIME· 350

EVIISIS_LICENSE_UNAVAILABLE· 351

EVIISIS_NBR_CHG·· 351

FCLINK messages· 351

FCLINK_FDISC_REJECT_NORESOURCE· 352

FCLINK_FLOGI_REJECT_NORESOURCE· 352

FCOE messages· 352

FCOE_INTERFACE_NOTSUPPORT_FCOE· 353

FCOE_LAGG_BIND_ACTIVE· 353

FCOE_LAGG_BIND_DEACTIVE· 354

FCZONE messages· 354

FCZONE_HARDZONE_DISABLED·· 354

FCZONE_HARDZONE_ENABLED·· 355

FCZONE_ISOLATE_NEIGHBOR· 355

FCZONE_ISOLATE_ALLNEIGHBOR· 356

FCZONE_ISOLATE_CLEAR_VSAN· 356

FCZONE_ISOLATE_CLEAR_ALLVSAN· 357

FCZONE_DISTRIBUTE_FAILED·· 357

FIB messages· 357

FIB_FILE· 358

FILTER messages· 358

FILTER_EXECUTION_ICMP· 358

FILTER_EXECUTION_ICMPV6· 359

FILTER_IPV4_EXECUTION· 360

FILTER_IPV6_EXECUTION· 361

FIPSNG messages· 361

FIPSNG_HARD_RESOURCE_NOENOUGH· 361

FIPSNG_HARD_RESOURCE_RESTORE· 362

FS messages· 362

FS_UNFORMATTED_PARTITION· 362

FTPD messages· 362

FTP_ACL_DENY· 363

FTPD_REACH_SESSION_LIMIT· 363

FTPD_AUTHOR_FAILED·· 363

HA messages· 364

HA_BATCHBACKUP_FINISHED·· 364

HA_BATCHBACKUP_STARTED·· 364

HA_STANDBY_NOT_READY· 365

HA_STANDBY_TO_MASTER· 365

HQOS messages· 365

HQOS_DP_SET_FAIL· 366

HQOS_FP_SET_FAIL· 366

HQOS_POLICY_APPLY_FAIL· 367

HQOS_POLICY_APPLY_FAIL· 367

HTTPD messages· 367

HTTPD_CONNECT· 368

HTTPD_CONNECT_TIMEOUT· 368

HTTPD_DISCONNECT· 368

HTTPD_FAIL_FOR_ACL· 369

HTTPD_FAIL_FOR_ACP· 369

HTTPD_REACH_CONNECT_LIMIT· 369

IFNET messages· 370

IF_BUFFER_CONGESTION_OCCURRENCE· 370

IF_BUFFER_CONGESTION_CLEAR· 370

INTERFACE_NOTSUPPRESSED·· 371

INTERFACE_SUPPRESSED·· 371

LINK_UPDOWN· 371

PHY_UPDOWN· 372

PROTOCOL_UPDOWN· 372

TUNNEL_LINK_UPDOWN· 372

TUNNEL_PHY_UPDOWN· 373

VLAN_MODE_CHANGE· 373

IKE messages· 373

IKE_P1_SA_ESTABLISH_FAIL· 374

IKE_P2_SA_ESTABLISH_FAIL· 375

IKE_P2_SA_TERMINATE· 375

IPSEC messages· 376

IPSEC_FAILED_ADD_FLOW_TABLE· 376

IPSEC_PACKET_DISCARDED·· 376

IPSEC_SA_ESTABLISH· 377

IPSEC_SA_ESTABLISH_FAIL· 377

IPSEC_SA_INITINATION· 378

IPSEC_SA_TERMINATE· 378

IPSG messages· 378

IPSG_ADDENTRY_ERROR· 379

IPSG_DELENTRY_ERROR· 380

IPSG_ADDEXCLUDEDVLAN_ERROR· 381

IPSG_DELEXCLUDEDVLAN_ERROR· 382

IRDP messages· 382

IRDP_EXCEED_ADVADDR_LIMIT· 382

IRF· 383

IRF_LINK_BLOCK· 383

IRF_LINK_DOWN· 383

IRF_LINK_UP· 383

IRF_MEMBERID_CONFLICT· 384

IRF_MERGE· 384

IRF_MERGE_NEED_REBOOT· 384

IRF_MERGE_NOT_NEED_REBOOT· 385

ISIS messages· 385

ISIS_LSP_CONFLICT· 385

ISIS_MEM_ALERT· 386

ISIS_NBR_CHG·· 386

ISSU messages· 386

ISSU_ROLLBACKCHECKNORMAL· 387

ISSU_PROCESSWITCHOVER· 387

L2PT messages· 387

L2PT_SET_MULTIMAC_FAILED·· 387

L2PT_CREATE_TUNNELGROUP_FAILED·· 388

L2PT_ADD_GROUPMEMBER_FAILED·· 388

L2PT_ENABLE_DROP_FAILED·· 388

L2TP messages· 388

L2TPV2_TUNNEL_EXCEED_LIMIT· 389

L2TPV2_SESSION_EXCEED_LIMIT· 389

L2VPN messages· 389

L2VPN_BGPVC_CONFLICT_LOCAL· 390

L2VPN_BGPVC_CONFLICT_REMOTE· 390

L2VPN_HARD_RESOURCE_NOENOUGH· 390

L2VPN_HARD_RESOURCE_RESTORE· 391

L2VPN_LABEL_DUPLICATE· 391

LAGG messages· 391

LAGG_ACTIVE· 392

LAGG_INACTIVE_AICFG·· 392

LAGG_INACTIVE_BFD·· 393

LAGG_INACTIVE_CONFIGURATION· 393

LAGG_INACTIVE_DUPLEX· 394

LAGG_INACTIVE_HARDWAREVALUE· 394

LAGG_INACTIVE_LOWER_LIMIT· 395

LAGG_INACTIVE_PARTNER· 395

LAGG_INACTIVE_PHYSTATE· 396

LAGG_INACTIVE_RESOURCE_INSUFICIE· 396

LAGG_INACTIVE_SPEED·· 397

LAGG_INACTIVE_UPPER_LIMIT· 397

LDP messages· 397

LDP_MPLSLSRID_CHG·· 398

LDP_SESSION_CHG·· 399

LDP_SESSION_GR· 400

LDP_SESSION_SP· 400

LLDP messages· 401

LLDP_CREATE_NEIGHBOR· 401

LLDP_DELETE_NEIGHBOR· 402

LLDP_LESS_THAN_NEIGHBOR_LIMIT· 402

LLDP_NEIGHBOR_AGE_OUT· 403

LLDP_NEIGHBOR_PROTECTION_BLOCK· 403

LLDP_NEIGHBOR_PROTECTION_DOWN· 404

LLDP_NEIGHBOR_PROTECTION_UNBLOCK· 404

LLDP_NEIGHBOR_PROTECTION_UP· 404

LLDP_PVID_INCONSISTENT· 405

LLDP_REACH_NEIGHBOR_LIMIT· 405

LOAD messages· 405

BOARD_LOADING·· 406

LOAD_FAILED·· 406

LOAD_FINISHED·· 406

LOGIN messages· 407

LOGIN_FAILED·· 407

LOGIN_ INVALID_USERNAME_PWD·· 407

LPDT messages· 407

LPDT_LOOPED·· 408

LPDT_RECOVERED·· 408

LPDT_VLAN_LOOPED·· 408

LPDT_VLAN_RECOVERED·· 409

LS messages· 409

LS_ADD_USER_TO_GROUP· 409

LS_AUTHEN_FAILURE· 410

LS_AUTHEN_SUCCESS· 410

LS_DEL_USER_FROM_GROUP· 411

LS_DELETE_PASSWORD_FAIL· 411

LS_PWD_ADDBLACKLIST· 411

LS_PWD_CHGPWD_FOR_AGEDOUT· 412

LS_PWD_CHGPWD_FOR_AGEOUT· 412

LS_PWD_CHGPWD_FOR_COMPOSITION· 412

LS_PWD_CHGPWD_FOR_FIRSTLOGIN· 413

LS_PWD_CHGPWD_FOR_LENGTH· 413

LS_PWD_FAILED2WRITEPASS2FILE· 413

LS_PWD_MODIFY_FAIL· 414

LS_PWD_MODIFY_SUCCESS· 414

LS_REAUTHEN_FAILURE· 415

LS_UPDATE_PASSWORD_FAIL· 415

LS_USER_CANCEL· 415

LS_USER_PASSWORD_EXPIRE· 416

LS_USER_ROLE_CHANGE· 416

LSPV messages· 416

LSPV_PING_STATIS_INFO·· 417

MAC messages· 417

MAC_DRIVER_ADD_ENTRY· 417

MAC_TABLE_FULL_GLOBAL· 418

MAC_TABLE_FULL_PORT· 418

MAC_TABLE_FULL_VLAN· 418

MAC_VLAN_LEARNLIMIT_NORESOURCE· 419

MAC_VLAN_LEARNLIMIT_NOTSUPPORT· 419

MACA messages· 419

MACA_ENABLE_NOT_EFFECTIVE· 419

MACA_LOGIN_FAILURE· 420

MACA_LOGIN_SUCC· 421

MACA_LOGIN_SUCC (in open mode) 421

MACA_LOGOFF· 422

MACA_LOGOFF (in open mode) 422

MACSEC messages· 422

MACSEC_MKA_KEEPALIVE_TIMEOUT· 423

MACSEC_MKA_PRINCIPAL_ACTOR· 423

MACSEC_MKA_SAK_REFRESH· 423

MACSEC_MKA_SESSION_REAUTH· 424

MACSEC_MKA_SESSION_SECURED·· 424

MACSEC_MKA_SESSION_START· 425

MACSEC_MKA_SESSION_STOP· 425

MACSEC_MKA_SESSION_UNSECURED·· 426

MBFD messages· 426

MBFD_TRACEROUTE_FAILURE· 426

MBUF messages· 427

MBUF_DATA_BLOCK_CREATE_FAIL· 427

MDC messages· 427

MDC_CREATE_ERR· 428

MDC_CREATE· 428

MDC_DELETE· 428

MDC_KERNEL_EVENT_TOOLONG·· 429

MDC_LICENSE_EXPIRE· 429

MDC_NO_FORMAL_LICENSE· 429

MDC_NO_LICENSE_EXIT· 430

MDC_OFFLINE· 430

MDC_ONLINE· 430

MDC_STATE_CHANGE· 431

MFIB messages· 431

MFIB_MEM_ALERT· 431

MGROUP messages· 431

MGROUP_APPLY_SAMPLER_FAIL· 432

MGROUP_RESTORE_CPUCFG_FAIL· 432

MGROUP_RESTORE_IFCFG_FAIL· 433

MGROUP_SYNC_CFG_FAIL· 433

MPLS messages· 433

MPLS_HARD_RESOURCE_NOENOUGH· 434

MPLS_HARD_RESOURCE_RESTORE· 434

MTLK messages· 434

MTLK_UPLINK_STATUS_CHANGE· 434

NAT messages· 435

NAT_ADDR_BIND_CONFLICT· 435

NAT_FAILED_ADD_FLOW_RULE· 435

NAT_FAILED_ADD_FLOW_TABLE· 436

NAT_FLOW·· 437

NAT_SERVER_INVALID·· 438

NAT_SERVICE_CARD_RECOVER_FAILURE· 439

ND messages· 439

ND_CONFLICT· 440

ND_DUPADDR· 440

ND_HOST_IP_CONFLICT· 441

ND_MAC_CHECK· 441

ND_RAGUARD_DROP· 442

ND_SET_PORT_TRUST_NORESOURCE· 442

ND_SET_VLAN_REDIRECT_NORESOURCE· 442

NETCONF messages· 442

CLI 443

row-operation· 444

THREAD·· 444

NQA messages· 445

NQA_LOG_UNREACHABLE· 445

NTP messages· 445

NTP_CLOCK_CHANGE· 445

NTP_LEAP_CHANGE· 446

NTP_SOURCE_CHANGE· 446

NTP_SOURCE_LOST· 447

NTP_STRATUM_CHANGE· 447

OBJP messages· 447

OBJP_ACCELERATE_NO_RES· 448

OBJP_ACCELERATE_NOT_SUPPORT· 448

OBJP_ACCELERATE_UNK_ERR· 448

OFP messages· 449

OFP_ACTIVE· 449

OFP_ACTIVE_FAILED·· 449

OFP_CONNECT· 449

OFP_FAIL_OPEN· 450

OFP_FLOW_ADD·· 450

OFP_FLOW_ADD_DUP· 451

OFP_FLOW_ADD_FAILED·· 451

OFP_FLOW_ADD_FAILED·· 452

OFP_FLOW_ADD_TABLE_MISS· 452

OFP_FLOW_ADD_TABLE_MISS_FAILED·· 453

OFP_FLOW_DEL· 453

OFP_FLOW_DEL_TABLE_MISS· 454

OFP_FLOW_DEL_TABLE_MISS_FAILED·· 454

OFP_FLOW_MOD·· 455

OFP_FLOW_MOD_FAILED·· 455

OFP_FLOW_MOD_TABLE_MISS· 456

OFP_FLOW_MOD_TABLE_MISS_FAILED·· 456

OFP_FLOW_RMV_GROUP· 457

OFP_FLOW_RMV_HARDTIME· 457

OFP_FLOW_RMV_IDLETIME· 457

OFP_FLOW_RMV_METER· 458

OFP_FLOW_UPDATE_FAILED·· 458

OFP_GROUP_ADD·· 459

OFP_GROUP_ADD_FAILED·· 459

OFP_GROUP_DEL· 460

OFP_GROUP_MOD·· 460

OFP_GROUP_MOD_FAILED·· 461

OFP_METER_ADD·· 461

OFP_METER_ADD_FAILED·· 461

OFP_METER_DEL· 462

OFP_METER_MOD·· 462

OFP_METER_MOD_FAILED·· 463

OFP_MISS_RMV_GROUP· 463

OFP_MISS_RMV_HARDTIME· 463

OFP_MISS_RMV_IDLETIME· 464

OFP_MISS_RMV_METER· 464

OFP_RADARDETECTION· 464

PORT_MOD·· 465

OPENSRC (FreeRADIUS) messages· 466

HUP event 466

Process restart event 467

Process start event 467

User authentication· 468

OPTMOD messages· 470

BIAS_HIGH· 470

BIAS_LOW·· 471

BIAS_NORMAL· 471

CFG_ERR· 471

CHKSUM_ERR· 472

FIBER_SFP MODULE_INVALID·· 472

FIBER_SFPMODULE_NOWINVALID·· 473

IO_ERR· 473

MOD_ALM_OFF· 473

MOD_ALM_ON· 474

MODULE_IN· 474

MODULE_OUT· 474

PHONY_MODULE· 475

RX_ALM_OFF· 475

RX_ALM_ON· 475

RX_POW_HIGH· 476

RX_POW_LOW·· 476

RX_POW_NORMAL· 476

TEMP_HIGH· 477

TEMP_LOW·· 477

TEMP_NORMAL· 477

TX_ALM_OFF· 478

TX_ALM_ON· 478

TX_POW_HIGH· 478

TX_POW_LOW·· 479

TX_POW_NORMAL· 479

TYPE_ERR· 479

VOLT_HIGH· 480

VOLT_LOW·· 480

VOLT_NORMAL· 480

OSPF messages· 481

OSPF_DUP_RTRID_NBR· 481

OSPF_IP_CONFLICT_INTRA· 481

OSPF_LAST_NBR_DOWN· 482

OSPF_MEM_ALERT· 482

OSPF_NBR_CHG·· 483

OSPF_RT_LMT· 483

OSPF_RTRID_CHG·· 483

OSPF_RTRID_CONFLICT_INTER· 484

OSPF_RTRID_CONFLICT_INTRA· 484

OSPF_VLINKID_CHG·· 484

OSPFV3 messages· 485

OSPFV3_LAST_NBR_DOWN· 485

OSPFV3_MEM_ALERT· 485

OSPFV3_NBR_CHG·· 486

OSPFV3_RT_LMT· 486

Packet capture messages· 486

PKTCPT_AP_OFFLINE· 487

PKTCPT_AREADY_EXIT· 487

PKTCPT_CONN_FAIL· 488

PKTCPT_INVALID_FILTER· 488

PKTCPT_LOGIN_DENIED·· 488

PKTCPT_MEMORY_ALERT· 489

PKTCPT_OPEN_FAIL· 489

PKTCPT_OPERATION_TIMEOUT· 489

PKTCPT_SERVICE_FAIL· 490

PKTCPT_UNKNOWN_ERROR· 490

PKTCPT_UPLOAD_ERROR· 490

PKTCPT_WRITE_FAIL· 491

PBB messages· 491

PBB_JOINAGG_WARNING·· 491

PBR messages· 491

PBR_HARDWARE_ERROR· 492

PCE messages· 492

PCE_PCEP_SESSION_CHG·· 493

PEX messages (IRF 3) 493

PEX_ASSOCIATEID_MISMATCHING·· 494

PEX_CONFIG_ERROR· 494

PEX_CONNECTION_ERROR· 495

PEX_FORBID_STACK· 495

PEX_LINK_BLOCK· 496

PEX_LINK_DOWN· 497

PEX_LINK_FORWARD·· 497

PEX_REG_JOININ· 498

PEX_REG_LEAVE· 498

PEX_REG_REQUEST· 499

PEX_STACKCONNECTION_ERROR· 499

PEX messages (IRF 3.1) 500

PEX_AUTOCONFIG_BAGG_ASSIGNMEMBER· 500

PEX_AUTOCONFIG_BAGG_CREATE· 500

PEX_AUTOCONFIG_BAGG_NORESOURCE· 500

PEX_AUTOCONFIG_BAGG_REMOVEMEMBER· 501

PEX_AUTOCONFIG_CAPABILITY_ENABLE· 501

PEX_AUTOCONFIG_CASCADELIMIT· 501

PEX_AUTOCONFIG_CONNECTION_ERROR· 502

PEX_AUTOCONFIG_DIFFGROUPNUMBER· 502

PEX_AUTOCONFIG_DYNAMICBAGG_STP· 503

PEX_AUTOCONFIG_GROUP_CREATE· 503

PEX_AUTOCONFIG_NONUMBERRESOURCE· 503

PEX_AUTOCONFIG_NOT_CASCADEPORT· 504

PEX_AUTOCONFIG_NUMBER_ASSIGN· 504

PEX_LLDP_DISCOVER· 505

PEX_MEMBERID_EXCEED·· 505

PEX_PECSP_OPEN_RCVD·· 505

PEX_PECSP_OPEN_SEND·· 506

PEX_PECSP_TIMEOUT· 506

PFILTER messages· 506

PFILTER_GLB_IPV4_DACT_NO_RES· 507

PFILTER_GLB_IPV4_DACT_UNK_ERR· 507

PFILTER_GLB_IPV6_DACT_NO_RES· 508

PFILTER_GLB_IPV6_DACT_UNK_ERR· 508

PFILTER_GLB_MAC_DACT_NO_RES· 509

PFILTER_GLB_MAC_DACT_UNK_ERR· 509

PFILTER_GLB_NO_RES· 510

PFILTER_GLB_NOT_SUPPORT· 510

PFILTER_GLB_ RES_CONFLICT· 511

PFILTER_GLB_UNK_ERR· 511

PFILTER_IF_IPV4_DACT_NO_RES· 512

PFILTER_IF_IPV4_DACT_UNK_ERR· 512

PFILTER_IF_IPV6_DACT_NO_RES· 513

PFILTER_IF_IPV6_DACT_UNK_ERR· 513

PFILTER_IF_MAC_DACT_NO_RES· 514

PFILTER_IF_MAC_DACT_UNK_ERR· 514

PFILTER_IF_NO_RES· 515

PFILTER_IF_NOT_SUPPORT· 515

PFILTER_IF_RES_CONFLICT· 516

PFILTER_IF_UNK_ERR· 516

PFILTER_IPV4_FLOW_INFO·· 517

PFILTER_IPV4_FLOWLOG_STATIS· 517

PFILTER_IPV6_FLOW_INFO·· 518

PFILTER_IPV6_FLOWLOG_STATIS· 518

PFILTER_IPV6_STATIS_INFO·· 519

PFILTER_MAC_FLOW_INFO·· 519

PFILTER_STATIS_INFO·· 520

PFILTER_VLAN_IPV4_DACT_NO_RES· 520

PFILTER_VLAN_IPV4_DACT_UNK_ERR· 521

PFILTER_VLAN_IPV6_DACT_NO_RES· 521

PFILTER_VLAN_IPV6_DACT_UNK_ERR· 522

PFILTER_VLAN_MAC_DACT_NO_RES· 522

PFILTER_VLAN_MAC_DACT_UNK_ERR· 523

PFILTER_VLAN_NO_RES· 523

PFILTER_VLAN_NOT_SUPPORT· 524

PFILTER_VLAN_RES_CONFLICT· 524

PFILTER_VLAN_UNK_ERR· 525

PIM messages· 525

PIM_NBR_DOWN· 525

PIM_NBR_UP· 526

PING messages· 526

PING_STATISTICS· 526

PING_VPN_STATISTICS· 527

PKI messages· 527

REQUEST_CERT_FAIL· 527

REQUEST_CERT_SUCCESS· 528

PKT2CPU messages· 528

PKT2CPU_NO_RESOURCE· 528

Portal messages· 528

PORTAL_RULE_FAILED·· 529

PORTSEC messages· 529

PORTSEC_ACL_FAILURE· 530

PORTSEC_CAR_FAILURE· 530

PORTSEC_CREATEAC_FAILURE· 531

PORTSEC_LEARNED_MACADDR· 531

PORTSEC_NTK_NOT_EFFECTIVE· 532

PORTSEC_PORTMODE_NOT_EFFECTIVE· 532

PORTSEC_PROFILE_FAILURE· 532

PORTSEC_URL_FAILURE· 533

PORTSEC_VIOLATION· 533

PPP messages· 533

IPPOOL_ADDRESS_EXHAUSTED·· 534

PPP_USER_LOGON_SUCCESS· 534

PPP_USER_LOGON_FAILED·· 535

PPP_USER_LOGOFF· 535

PWDCTL messages· 536

ADDBLACKLIST· 536

CHANGEPASSWORD·· 537

FAILEDTOWRITEPWD·· 537

QOS messages· 537

MIRROR_SYNC_CFG_FAIL· 538

QOS_CAR_APPLYUSER_FAIL· 538

QOS_CBWFQ_REMOVED·· 539

QOS_GTS_APPLYUSER_FAIL· 539

QOS_NOT_ENOUGH_BANDWIDTH· 540

QOS_POLICY_APPLYCOPP_CBFAIL· 540

QOS_POLICY_APPLYCOPP_FAIL· 541

QOS_POLICY_APPLYGLOBAL_CBFAIL· 541

QOS_POLICY_APPLYGLOBAL_FAIL· 542

QOS_POLICY_APPLYIF_CBFAIL· 542

QOS_POLICY_APPLYIF_FAIL· 543

QOS_POLICY_APPLYUSER_FAIL· 543

QOS_POLICY_APPLYVLAN_CBFAIL· 544

QOS_POLICY_APPLYVLAN_FAIL· 544

QOS_QMPROFILE_APPLYUSER_FAIL· 545

QOS_QMPROFILE_MODIFYQUEUE_FAIL· 545

WRED_TABLE_CFG_FAIL· 546

RADIUS messages· 546

RADIUS_AUTH_FAILURE· 546

RADIUS_AUTH_SUCCESS· 547

RADIUS_DELETE_HOST_FAIL· 547

RDDC messages· 547

RDDC_ACTIVENODE_CHANGE· 548

RESMON·· 548

RESMON_MINOR· 548

RESMON_MINOR_RECOVERY· 549

RESMON_SEVERE· 549

RESMON_SEVERE_RECOVERY· 550

RESMON_USEDUP· 550

RESMON_USEDUP_RECOVERY· 551

RIP messages· 551

RIP_MEM_ALERT· 551

RIP_RT_LMT· 552

RIPNG messages· 552

RIPNG_MEM_ALERT· 552

RIPNG_RT_LMT· 552

RM messages· 552

RM_ACRT_REACH_LIMIT· 553

RM_ACRT_REACH_THRESVALUE· 553

RM_THRESHLD_VALUE_REACH· 554

RM_TOTAL_THRESHLD_VALUE_REACH· 554

RPR messages· 554

RPR_EXCEED_MAX_SEC_MAC· 555

RPR_EXCEED_MAX_SEC_MAC_OVER· 555

RPR_EXCEED_MAX_STATION· 555

RPR_EXCEED_MAX_STATION_OVER· 556

RPR_EXCEED_RESERVED_RATE· 556

RPR_EXCEED_RESERVED_RATE_OVER· 556

RPR_IP_DUPLICATE· 557

RPR_IP_DUPLICATE_OVER· 557

RPR_JUMBO_INCONSISTENT· 557

RPR_JUMBO_INCONSISTENT_OVER· 558

RPR_MISCABLING·· 558

RPR_MISCABLING_OVER· 558

RPR_PROTECTION_INCONSISTENT· 559

RPR_PROTECTION_INCONSISTENT_OVER· 559

RPR_SEC_MAC_DUPLICATE· 559

RPR_SEC_MAC_DUPLICATE_OVER· 560

RPR_TOPOLOGY_INCONSISTENT· 560

RPR_TOPOLOGY_INCONSISTENT_OVER· 560

RPR_TOPOLOGY_INSTABILITY· 561

RPR_TOPOLOGY_INSTABILITY_OVER· 561

RPR_TOPOLOGY_INVALID·· 561

RPR_TOPOLOGY_INVALID_OVER· 562

RRPP messages· 562

RRPP_RING_FAIL· 562

RRPP_RING_RESTORE· 562

RTM messages· 562

RTM_TCL_NOT_EXIST· 563

RTM_TCL_MODIFY· 563

RTM_TCL_LOAD_FAILED·· 563

SCM messages· 563

PROCESS_ABNORMAL· 564

PROCESS_ACTIVEFAILED·· 564

SCM_ABNORMAL_REBOOT· 565

SCM_ABNORMAL_REBOOTMDC· 566

SCM_ABORT_RESTORE· 566

SCM_INSMOD_ADDON_TOOLONG·· 567

SCM_KERNEL_INIT_TOOLONG·· 567

SCM_PROCESS_STARTING_TOOLONG·· 568

SCM_PROCESS_STILL_STARTING·· 568

SCM_SKIP_PROCESS· 569

SCM_SKIP_PROCESS· 569

SCRLSP messages· 569

SCRLSP_LABEL_DUPLICATE· 570

SESSION messages· 570

SESSION_IPV4_FLOW·· 571

SESSION_IPV6_FLOW·· 572

SFLOW messages· 573

SFLOW_HARDWARE_ERROR· 573

SHELL messages· 573

SHELL_CMD·· 574

SHELL_CMD_CONFIRM·· 574

SHELL_CMD_EXECUTEFAIL· 574

SHELL_CMD_INPUT· 575

SHELL_CMD_INPUT_TIMEOUT· 575

SHELL_CMD_MATCHFAIL· 575

SHELL_CMDDENY· 576

SHELL_CMDFAIL· 576

SHELL_COMMIT· 576

SHELL_COMMIT_DELAY· 577

SHELL_COMMIT_REDELAY· 577

SHELL_COMMIT_ROLLBACK· 577

SHELL_COMMIT_ROLLBACKDONE· 578

SHELL_COMMIT_WILLROLLBACK· 578

SHELL_CRITICAL_CMDFAIL· 578

SHELL_LOGIN· 579

SHELL_LOGOUT· 579

SLSP messages· 579

SLSP_LABEL_DUPLICATE· 580

SMLK messages· 580

SMLK_LINK_SWITCH· 580

SNMP messages· 580

SNMP_ACL_RESTRICTION· 581

SNMP_AUTHENTICATION_FAILURE· 581

SNMP_GET· 581

SNMP_NOTIFY· 582

SNMP_SET· 582

SNMP_USM_NOTINTIMEWINDOW·· 583

SSHS messages· 583

SSHS_ACL_DENY· 583

SSHS_ALGORITHM_MISMATCH· 584

SSHS_AUTH_EXCEED_RETRY_TIMES· 584

SSHS_AUTH_FAIL· 585

SSHS_AUTH_TIMEOUT· 585

SSHS_CONNECT· 585

SSHS_DECRYPT_FAIL· 586

SSHS_DISCONNECT· 586

SSHS_ENCRYPT_FAIL· 586

SSHS_LOG·· 587

SSHS_MAC_ERROR· 587

SSHS_REACH_SESSION_LIMIT· 588

SSHS_REACH_USER_LIMIT· 588

SSHS_SCP_OPER· 588

SSHS_SFTP_OPER· 589

SSHS_SRV_UNAVAILABLE· 589

SSHS_VERSION_MISMATCH· 590

STAMGR messages· 590

STAMGR_ADD_FAILVLAN· 590

STAMGR_ADDBAC_INFO·· 590

STAMGR_ADDSTA_INFO·· 591

STAMGR_AUTHORACL_FAILURE· 591

STAMGR_AUTHORUSERPROFILE_FAILURE· 592

STAMGR_CLIENT_OFFLINE· 592

STAMGR_CLIENT_ONLINE· 593

STAMGR_DELBAC_INFO·· 593

STAMGR_DELSTA_INFO·· 593

STAMGR_DOT1X_LOGIN_FAILURE· 594

STAMGR_DOT1X_LOGIN_SUCC· 594

STAMGR_DOT1X_LOGOFF· 595

STAMGR_MACA_LOGIN_FAILURE· 595

STAMGR_MACA_LOGIN_SUCC· 596

STAMGR_MACA_LOGOFF· 596

STAMGR_STAIPCHANGE_INFO·· 597

STAMGR_TRIGGER_IP· 597

STM messages· 597

STM_AUTO_UPDATE_FAILED·· 598

STM_AUTO_UPDATE_FINISHED·· 599

STM_AUTO_UPDATING·· 599

STM_LINK_DOWN· 600

STM_LINK_TIMEOUT· 600

STM_LINK_UP· 600

STM_MERGE· 601

STM_MERGE_NEED_REBOOT· 601

STM_MERGE_NOT_NEED_REBOOT· 601

STM_SAMEMAC· 602

STM_SOMER_CHECK· 602

STP messages· 602

STP_BPDU_PROTECTION· 602

STP_BPDU_RECEIVE_EXPIRY· 603

STP_CONSISTENCY_RESTORATION· 603

STP_DETECTED_TC· 603

STP_DISABLE· 604

STP_DISCARDING·· 604

STP_DISPUTE· 604

STP_ENABLE· 605

STP_FORWARDING·· 605

STP_LOOP_PROTECTION· 605

STP_LOOPBACK_PROTECTION· 606

STP_NOT_ROOT· 606

STP_NOTIFIED_TC· 606

STP_PORT_TYPE_INCONSISTENCY· 607

STP_PVID_INCONSISTENCY· 607

STP_PVST_BPDU_PROTECTION· 607

STP_ROOT_PROTECTION· 608

SYSLOG messages· 608

SYSLOG_LOGFILE_FULL· 608

SYSLOG_NO_SPACE· 608

SYSLOG_RESTART· 609

SYSLOG_RTM_EVENT_BUFFER_FULL· 609

TACACS messages· 609

TACACS_AUTH_FAILURE· 610

TACACS_AUTH_SUCCESS· 610

TACACS_DELETE_HOST_FAIL· 610

TELNETD messages· 610

TELNETD_ACL_DENY· 611

TELNETD_REACH_SESSION_LIMIT· 611

TRILL messages· 611

TRILL_DUP_SYSTEMID·· 612

TRILL_INTF_CAPABILITY· 612

TRILL_LICENSE_EXPIRED·· 612

TRILL_LICENSE_EXPIRED_TIME· 613

TRILL_LICENSE_UNAVAILABLE· 613

TRILL_MEM_ALERT· 613

TRILL_NBR_CHG·· 614

VCF messages· 614

VCF_AGGR_CREAT· 614

VCF_AGGR_DELETE· 615

VCF_AGGR_FAILED·· 615

VCF_AUTO_ANALYZE_USERDEF· 615

VCF_AUTO_NO_USERDEF· 616

VCF_AUTO_START· 616

VCF_AUTO_STATIC_CMD·· 617

VCF_BGP· 617

VCF_DOWN_LINK· 618

VCF_GET_IMAGE· 618

VCF_GET_TEMPLATE· 619

VCF_INSTALL_IMAGE· 619

VCF_IRF_FINISH· 619

VCF_IRF_FOUND·· 620

VCF_IRF_REBOOT· 620

VCF_IRF_START· 621

VCF_LOOPBACK_START· 621

VCF_LOOPBACK_START_FAILED·· 622

VCF_LOOPBACK_ALLOC· 622

VCF_LOOPBACK_NO_FREE_IP· 623

VCF_LOOPBACK_RECLAIM·· 623

VCF_REBOOT· 624

VCF_SKIP_INSTALL· 624

VCF_STATIC_CMD_ERROR· 624

VCF_UP_LINK· 625

VLAN messages· 625

VLAN_FAILED·· 625

VLAN_VLANMAPPING_FAILED·· 626

VLAN_VLANTRANSPARENT_FAILED·· 626

VRRP messages· 626

VRRP_STATUS_CHANGE· 627

VRRP_VF_STATUS_CHANGE· 628

VRRP_VMAC_INEFFECTIVE· 628

VSRP messages· 628

VSRP_BIND_FAILED·· 629

VXLAN messages· 629

VXLAN_LICENSE_UNAVAILABLE· 629


Introduction

This document includes system messages for the Comware 7 software platform. Some messages might not be available on the device.

This document assumes that the readers are familiar with data communications technologies and H3C networking products.

System log message format

By default, the system log messages use one of the following formats depending on the output destination:

·     Log host:

<PRI>TIMESTAMP Sysname %%vendorMODULE/severity/MNEMONIC: location; CONTENT

·     Destinations except for the log host:

Prefix TIMESTAMP Sysname MODULE/severity/MNEMONIC: CONTENT

Table 1 System log message elements

Element

Description

<PRI>

Priority identifier. It is calculated by using the following formula:

Priority identifier=facilityx8+severity

Where:

·     Facility is specified by using the info-center loghost command. A log host uses this parameter to identify log sources and filter log messages.

·     Severity represents the importance of the message. For more information about severity levels, see Table 2.

Prefix

Message type identifier. This element is contained in the system log messages sent to non-log host destinations.

The element uses the following symbols to indicate message severity:

·     Percentage sign (%)—Informational and higher levels.

·     Asterisk (*)—Debug level.

TIMESTAMP

Date and time when the event occurred.

The following are commands for configuring the timestamp format:

·     Log host—Use the info-center timestamp loghost command.

·     Non-log host destinationsUse the info-center timestamp command.

Sysname

Name or IP address of the device that generated the message.

%%vendor

Manufacturer flag. This element is %%10 for H3C.

This element is only available in messages sent to the log host.

MODULE

Name of the module that produced the message.

severity

Severity level of the message. (For more information about severity levels, see Table 2.)

MNEMONIC

Text string that uniquely identifies the system message. The maximum length is 32 characters.

location

Optional. This element presents location information for the message in the following format:

-attribute1=x-attribute2=y…-attributeN=z

This element is separated from the message description by using a semicolon (;).

CONTENT

Text string that contains detailed information about the event or error.

For variable fields in this element, this document uses the representations in Table 3.

 

System log messages are classified into eight severity levels from 0 to 7. The lower the number, the higher the severity, as shown in Table 2.

Table 2 System log message severity levels

Level

Severity

Description

0

Emergency

The system is unusable. For example, the system authorization has expired.

1

Alert

Action must be taken immediately. For example, traffic on an interface exceeds the upper limit.

2

Critical

Critical condition. For example, the device temperature exceeds the upper limit, the power module fails, or the fan tray fails.

3

Error

Error condition. For example, the link state changes or a storage card is unplugged.

4

Warning

Warning condition. For example, an interface is disconnected, or the memory resources are used up.

5

Notification

Normal but significant condition. For example, a terminal logs in to the device, or the device reboots.

6

Informational

Informational message. For example, a command or a ping operation is executed.

7

Debug

Debugging message.

 

For variable fields in the message text, this document uses the representations in Table 3. The values are case insensitive, even though the representations are uppercase letters.

Table 3 Variable field representations

Representation

Information type

INT16

Signed 16-bit decimal number.

UINT16

Unsigned 16-bit decimal number.

INT32

Signed 32-bit decimal number.

UINT32

Unsigned 32-bit decimal number.

INT64

Signed 64-bit decimal number.

UINT64

Unsigned 64-bit decimal number.

DOUBLE

Two dot-separated signed 32-bit decimal numbers. The format is [INTEGER].[INTEGER].

HEX

Hexadecimal number.

CHAR

Single character.

STRING

Character string.

IPADDR

IP address.

MAC

MAC address.

DATE

Date.

TIME

Time.

 

Managing and obtaining system log messages

You can manage system log messages by using the information center.

By default, the information center is enabled. Log messages can be output to the console, log buffer, monitor terminal, log host, and log file.

To filter log messages, use the info-center source command to specify log output rules. A log output rule specifies the source modules and the lowest severity level of log messages that can be output to a destination. A log message is output if its severity level is higher than or equal to the specified level. For example, if you specify a severity level of 6 (informational), log messages that have a severity level from 0 to 6 are output.

For more information about using the information center, see the network management and monitoring configuration guide for the product.

Obtaining log messages from the console terminal

Access the device through the console port. Real-time log messages are displayed on the console terminal.

Obtaining log messages from the log buffer

Use the display logbuffer command to display history log messages in the log buffer.

Obtaining log messages from a monitor terminal

Monitor terminals refer to terminals that access the device through the AUX, VTY, or TTY lines (for example, Telnet). To obtain log messages from a monitor terminal, use the following guidelines:

·     To display log messages on the monitor terminal, you must configure the terminal monitor command.

·     For monitor terminals, the lowest level of log messages that can be displayed is determined by both the terminal logging level and info-center source commands.

Obtaining log messages from the log file

By default, the log file feature automatically saves logs from the log file buffer to the log file every 24 hours. You can use the info-center logfile frequency command to change the automatic saving internal.

To manually save logs to the log file, use the logfile save command. The log file buffer is cleared each time a save operation is performed.

By default, you can obtain the log file from the flash:/logfile/ path.

Obtaining log messages from a log host

Use the info-center loghost command to specify the service port number and IP address of a log host. To specify multiple log hosts, repeat the command.

For a successful log message transmission, make sure the specified port number is the same as the port number used on the log host. The default service port number is 514.

Software module list

Table 4 lists all software modules that might produce system log messages. This document uses "OPENSRC" to represent all open source modules.

Table 4 Software module list

Module name representation

Module name expansion

AAA

Authentication, Authorization and Accounting

ACL

Access Control List

ANCP

Access Node Control Protocol

APMGR

Access Point Management

ARP

Address Resolution Protocol

ATK

Attack Detection and Prevention

ATM

Asynchronous Transfer Mode

BFD

Bidirectional Forwarding Detection

BGP

Border Gateway Protocol

BLS

Blacklist

CFD

Connectivity Fault Detection

CFGMAN

Configuration Management

CONNLMT

Connection Limit

DEV

Device Management

DHCP

Dynamic Host Configuration Protocol

DHCPR

IPv4 DHCP Relay

DHCPS

DHCP Server

DHCPS6

DHCPv6 Server

DHCPSP4

DHCP Snooping

DHCPSP6

DHCPv6 Snooping

DIAG

Diagnosis

DLDP

Device Link Detection Protocol

DOT1X

802.1X

EDEV

Extended-Device Management

ERPS

Ethernet Ring Protection Switching

ETHOAM

Ethernet Operation, Administration and Maintenance

EVB

Edge Virtual Bridging

EVIISIS

Ethernet Virtual Interconnect Intermediate System-to-Intermediate System

FCOE

Fibre Channel Over Ethernet

FCLINK

Fibre Channel Link

FCZONE

Fibre Channel Zone

FIB

Forwarding Information Base

FILTER

Filter

FIPS

FIP Snooping

FTPD

File Transfer Protocol Daemon

HA

High Availability

HQOS

Hierarchical QoS

HTTPD

Hypertext Transfer Protocol Daemon

IFNET

Interface Net Management

IKE

Internet Key Exchange

IPSEC

IP Security

IPSG

IP Source Guard

IRDP

ICMP Router Discovery Protocol

ISIS

Intermediate System-to-Intermediate System

ISSU

In-Service Software Upgrade

L2TP

Layer 2 Tunneling Protocol

L2VPN

Layer 2 VPN

LAGG

Link Aggregation

LDP

Label Distribution Protocol

LLDP

Link Layer Discovery Protocol

LOAD

Load Management

LOGIN

Login

LPDT

Loopback Detection

LS

Local Server

LSPV

LSP Verification

MAC

Media Access Control

MACA

MAC Authentication

MACSEC

MAC Security

MBFD

MPLS BFD

MDC

Multitenant Device Context

MFIB

Multicast Forwarding Information Base

MGROUP

Mirroring group

MPLS

Multiprotocol Label Switching

MTLK

Monitor Link

NAT

Network Address Translation

ND

Neighbor Discovery

NQA

Network Quality Analyzer

NTP

Network Time Protocol

OPENSRC

Open Source

OBJP

Object Policy

OFP

OpenFlow Protocol

OPTMOD

Optical Module

OSPF

Open Shortest Path First

OSPFV3

Open Shortest Path First Version 3

Packet Capture

Packet Capture

PBB

Provider Backbone Bridge

PBR

Policy-Based Routing

PCE

Path Computation Element

PEX

Port Extender

PIM

Protocol Independent Multicast

PING

Packet Internet Groper

PKI

Public Key Infrastructure

PKT2CPU

Packet to CPU

PORTSEC

Port Security

PPP

Point to Point Protocol

PWDCTL

Password Control

QOS

Quality of Service

RADIUS

Remote Authentication Dial In User Service

RDDC

Redundancy

RIP

Routing Information Protocol

RIPNG

Routing Information Protocol Next Generation

RM

Routing Management

RRPP

Rapid Ring Protection Protocol

RTM

Real-Time Event Manager

SCM

Service Control Manager

SCRLSP

Static CRLSP

SESSION

Session

SFLOW

Sampler Flow

SHELL

Shell

SLSP

Static LSP

SMLK

Smart Link

SNMP

Simple Network Management Protocol

SSHS

Secure Shell Server

STAMGR

Station Management

STM

Stack Topology Management

STP

Spanning Tree Protocol

SYSEVENT

System Event

SYSLOG

System Log

TACACS

Terminal Access Controller Access Control System

TELNETD

Telnet Daemon

TRILL

Transparent Interconnect of Lots of Links

VCF

Vertical Converged Framework

VLAN

Virtual Local Area Network

VRRP

Virtual Router Redundancy Protocol

VSRP

Virtual Service Redundancy Protocol

WIPS

Wireless Intrusion Prevention System

 

Using this document

This document categorizes system log messages by software module. The modules are ordered alphabetically. Except for OPENSRC, the system log messages for each module are listed in alphabetic order of their mnemonic names. The OPENSRC messages are unordered because they use the same mnemonic name (SYSLOG). For each OPENSRC message, the section title uses a short description instead of the mnemonic name.

This document explains messages in tables. Table 5 describes information provided in these tables.

Table 5 Message explanation table contents

Item

Content

Example

Message text

Presents the message description.

ACL [UINT32] [STRING] [UINT64] packet(s).

Variable fields

Briefly describes the variable fields in the order that they appear in the message text.

The variable fields are numbered in the "$Number" form to help you identify their location in the message text.

$1: ACL number.

$2: ID and content of an ACL rule.

$3: Number of packets that matched the rule.

Severity level

Provides the severity level of the message.

6

Example

Provides a real message example. The examples do not include the "<PRI>TIMESTAMP Sysname %%vendor" part or the "Prefix TIMESTAMP Sysname" part, because information in this part varies with system settings.

ACL/6/ACL_STATIS_INFO: ACL 2000 rule 0 permit source 1.1.1.1 0 logging 10000 packet(s).

Explanation

Explains the message, including the event or error cause.

Number of packets that matched an ACL rule. This message is sent when the packet counter changes.

Recommended action

Provides recommended actions. For informational messages, no action is required.

No action is required.

 


AAA messages

This section contains AAA messages.

AAA_FAILURE

Message text

-AAAType=[STRING]-AAADomain=[STRING]-Service=[STRING]-UserName=[STRING]; AAA failed.

Variable fields

$1: AAA type.

$2: AAA scheme.

$3: Service.

$4: Username.

Severity level

5

Example

AAA/5/AAA_FAILURE: -AAAType=AUTHOR-AAADomain=domain1-Service=login-UserName=cwf@system; AAA failed.

Explanation

An AAA request was rejected.

The following are the common reasons:

·     No response was received from the server.

·     The username or password was incorrect.

·     The service type that the user applied for was incorrect.

Recommended action

1.     Verify that the device is correctly connected to the server.

2.     Enter the correct username and password.

3.     Verify that the server settings are the same as the settings on the device.

4.     If the problem persists, contact H3C Support.

 

AAA_LAUNCH

Message text

-AAAType=[STRING]-AAADomain=[STRING]-Service=[STRING]-UserName=[STRING]; AAA launched.

Variable fields

$1: AAA type.

$2: AAA scheme.

$3: Service.

$4: Username.

Severity level

6

Example

AAA/6/AAA_LAUNCH: -AAAType=AUTHEN-AAADomain=domain1-Service=login-UserName=cwf@system; AAA launched.

Explanation

An AAA request was received.

Recommended action

No action is required.

 

AAA_SUCCESS

Message text

-AAAType=[STRING]-AAADomain=[STRING]-Service=[STRING]-UserName=[STRING]; AAA succeeded.

Variable fields

$1: AAA type.

$2: AAA scheme.

$3: Service.

$4: Username.

Severity level

6

Example

AAA/6/AAA_SUCCESS: -AAAType=AUTHOR-AAADomain=domain1-Service=login-UserName=cwf@system; AAA succeeded.

Explanation

An AAA request was accepted.

Recommended action

No action is required.

 

ACL messages

This section contains ACL messages.

ACL_ACCELERATE_NO_RES

Message text

Failed to accelerate [STRING] ACL [UINT32]. The resources are insufficient.

Variable fields

$1: ACL type.

$2: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NO_RES: Failed to accelerate IPv6 ACL 2001. The resources are insufficient.

Explanation

Hardware resources were insufficient for accelerating an ACL.

Recommended action

Delete some rules or disabled ACL acceleration for other ACLs to release hardware resources.

 

ACL_ACCELERATE_NONCONTIGUOUSMASK

Message text

Failed to accelerate ACL [UINT32]. ACL acceleration supports only contiguous wildcard masks.

Variable fields

$1: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NONCONTIGUOUSMASK: Failed to accelerate ACL 2001. ACL acceleration supports only contiguous wildcard masks.

Explanation

ACL acceleration failed because rules containing noncontiguous wildcard masks exist in the ACL.

Recommended action

Check the ACL rules and delete the unsupported configuration.

 

ACL_ACCELERATE_NOT_SUPPORT

Message text

Failed to accelerate [STRING] ACL [UINT32]. The operation is not supported.

Variable fields

$1: ACL type.

$2: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NOT_SUPPORT: Failed to accelerate IPv6 ACL 2001. The operation is not supported.

Explanation

ACL acceleration failed because the system does not support ACL acceleration.

Recommended action

No action is required.

 

ACL_ACCELERATE_NOT_SUPPORTHOPBYHOP

Message text

Failed to accelerate IPv6 ACL [UINT32]. ACL acceleration does not support the rules that contain the hop-by-hop keywords.

Variable fields

$1: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NOT_SUPPORTHOPBYHOP: Failed to accelerate IPv6 ACL 2001. ACL acceleration does not support the rules that contain the hop-by-hop keywords.

Explanation

ACL acceleration failed for the IPv6 ACL because rules containing the hop-by-hop keyword exist in the ACL.

Recommended action

Check the ACL rules and delete the unsupported configuration.

 

ACL_ACCELERATE_NOT_SUPPORTMULTITCPFLAG

Message text

Failed to accelerate IPv6 ACL [UINT32]. ACL acceleration does not support specifying multiple TCP flags in one rule.

Variable fields

$1: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NOT_SUPPORTMULTITCPFLAG: Failed to accelerate IPv6 ACL 2001. ACL acceleration does not support specifying multiple TCP flags in one rule.

Explanation

ACL acceleration failed for the IPv6 ACL because rules containing multiple TCP flags exist in the ACL.

Recommended action

Check the ACL rules and delete the unsupported configuration.

 

ACL_ACCELERATE_UNK_ERR

Message text

Failed to accelerate [STRING] ACL [UINT32].

Variable fields

$1: ACL type.

$2: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_UNK_ERR: Failed to accelerate IPv6 ACL 2001.

Explanation

ACL acceleration failed because of an unknown error.

Recommended action

No action is required.

 

ACL_IPV6_STATIS_INFO

Message text

IPv6 ACL [UINT32] [STRING] [UINT64] packet(s).

Variable fields

$1: ACL number.

$2: ID and content of an IPv6 ACL rule.

$3: Number of packets that matched the rule.

Severity level

6

Example

ACL6/6/ACL_IPV6_STATIS_INFO: IPv6 ACL 2000 rule 0 permit source 1:1::/64 logging 1000 packet(s).

Explanation

The number of packets matching the IPv6 ACL rule changed.

Recommended action

No action is required.

 

ACL_NO_MEM

Message text

Failed to configure [STRING] ACL [UINT] due to lack of memory.

Variable fields

$1: ACL type.

$2: ACL number.

Severity level

3

Example

ACL/3/ACL_NO_MEM: Failed to configure ACL 2001 due to lack of memory.

Explanation

Configuring the ACL failed because memory is insufficient.

Recommended action

Use the display memory-threshold command to check the memory usage.

 

ACL_STATIS_INFO

Message text

ACL [UINT32] [STRING] [UINT64] packet(s).

Variable fields

$1: ACL number.

$2: ID and content of an IPv4 ACL rule.

$3: Number of packets that matched the rule.

Severity level

6

Example

ACL/6/ACL_STATIS_INFO: ACL 2000 rule 0 permit source 1.1.1.1 0 logging 10000 packet(s).

Explanation

The number of packets matching the IPv4 ACL rule changed.

Recommended action

No action is required.

 

ANCP messages

This section contains ANCP messages.

ANCP_INVALID_PACKET

Message text

-NeighborName=[STRING]-State=[STRING]-MessageType=[STRING]; The [STRING] value [STRING] is wrong, and the value [STRING] is expected.

Variable fields

$1: ANCP neighbor name.

$2: Neighbor state.

$3: Message type.

$4: Field.

$5: Wrong value of the field.

$6: Expected value of the field.

Severity level

6

Example

ANCP/6/ANCP_INVALID_PACKET: -NeighborName=Dslam-State=SYNSENT-MessageType=SYNACK; The Sender Instance value 0 is wrong, and the value 1 is expected.

Explanation

The system received an adjacency message that had a field with a wrong value.

Recommended action

No action is required.

 

ARP messages

This section contains ARP messages.

ARP_ACTIVE_ACK_NO_REPLY

Message text

No ARP reply from IP [STRING] was received on interface [STRING].

Variable fields

$1: IP address.

$2: Interface name.

Severity level

6

Example

ARP/6/ARP_ACTIVE_ACK_NO_REPLY: No ARP reply from IP 192.168.10.1 was received on interface GigabitEthernet1/0/1.

Explanation

The ARP active acknowledgement feature did not receive an ARP reply after it sent an ARP request to the sender IP of an ARP message.

This message indicates the risk of attacks.

Recommended action

5.     Verify that the learned ARP entries on the device are consistent with the existing legal devices. When gateways and servers are on the network, check the ARP entries for these devices first.

6.     If the ARP entries are correct and the attack continues, contact H3C Support.

 

ARP_ACTIVE_ACK_NOREQUESTED_REPLY

Message text

Interface [STRING] received from IP [STRING] an ARP reply that was not requested by the device.

Variable fields

$1: Interface name.

$2: IP address.

Severity level

6

Example

ARP/6/ARP_ACTIVE_ACK_NOREQUESTED_REPLY: Interface GigabitEthernet1/0/1 received from IP 192.168.10.1 an ARP reply that was not requested by the device.

Explanation

The ARP active acknowledgement feature received an unsolicited ARP reply from a sender IP.

This message indicates the risk of attacks.

Recommended action

No action is required. The device discards the ARP reply automatically.

 

ARP_BINDRULETOHW_FAILED

Message text

Failed to download binding rule to hardware on the interface [STRING], SrcIP [IPADDR], SrcMAC [MAC], VLAN [UINT16], Gateway MAC [MAC].

Variable fields

$1: Interface name.

$2: Source IP address.

$3: Source MAC address.

$4: VLAN ID.

$5: Gateway MAC address.

Severity level

5

Example

ARP/5/ARP_BINDRULETOHW_FAILED: Failed to download binding rule to hardware on the interface Ethernet1/0/1, SrcIP 1.1.1.132, SrcMAC 0015-E944-A947, VLAN 1, Gateway MAC 00A1-B812-1108.

Explanation

The system failed to set a binding rule to the hardware on an interface. The message is sent in any of the following situations:

·     The resources are not sufficient for the operation.

·     The memory is not sufficient for the operation.

·     A hardware error occurs.

Recommended action

To resolve the problem:

1.     Execute the display qos-acl resource command to check if the ACL resources for the operation are sufficient.

¡     If yes, proceed to step 2.

¡     If no, delete unnecessary configuration to release ACL resources. If no configuration can be deleted, proceed to step 2.

2.     Execute the display memory command to check if the memory for the operation is sufficient.

¡     If yes, proceed to step 3.

¡     If no, delete unnecessary configuration to release memory. If no configuration can be deleted, proceed to step 3.

3.     Delete the configuration and perform the operation again.

 

ARP_DETECTION_LOG

Message text

Detected an ARP attack on interface [STRING]: IP [STRING], MAC [STRING], VLAN [STRING]. [UINT32] packet(s) dropped.

Variable fields

$1: Interface name.

$2: IP address.

$3: MAC address.

$4: VLAN ID.

$5: Number of dropped packets.

Severity level

5

Example

ARP/5/ARP_INSPECTION: -MDC=1; Detected an ARP attack on interface GigabitEthernet1/0/1: IP 1.1.1.1, MAC 0001-0001-0001, VLAN 100. 2 packet(s) dropped.

Explanation

An ARP attack was detected on an interface and attack packets were dropped.

Recommended action

Check the source of the ARP attack.

 

ARP_DUPLICATE_IPADDR_DETECT

Message text

Detected an IP address conflict. The device with MAC address [STRING] connected to interface [STRING] in VSI [STRING] and the device with MAC address [STRING] connected to interface [STRING] in VSI [STRING] were using the same IP address [IPADDR].

Variable fields

$1: MAC address.

$2: Interface name. (The interface can be a tunnel interface, Layer 3 interface, or Ethernet service instance.)

$3: VSI name.

$4: MAC address.

$5: Interface name. (The interface can be a tunnel interface, Layer 3 interface, or Ethernet service instance.)

$6: VSI name.

$7: Conflicting IP address.

Severity level

6

Example

ARP/6/ARP_DUPLICATE_IPADDR_DETECT: Detected an IP address conflict. The device with MAC address 00-00-01 connected to interface GigabitEthernet1/0/1 service-instance 1000 in VSI vpna and the device with MAC address 0011-0011-0002 connected to interface tunnel 10 in VSI vpna were using the same IP address 192.168.1.1.

Explanation

This message is sent when an interface receives an ARP message in which the sender information conflicts with an existing ARP entry. The sender IP address is the same as the IP address in the entry, but the MAC addresses are different.

Recommended action

Change the IP address on either of the two devices.

 

ARP_DYNAMIC

Message text

The maximum number of dynamic ARP entries for the device reached.

Variable fields

N/A

Severity level

6

Example

ARP/6/ ARP_DYNAMIC_IF: The maximum number of dynamic ARP entries for interface GigabitEthernet1/0/1 reached.

Explanation

The maximum number of dynamic ARP entries for the device was reached.

Recommended action

No action is required.

 

ARP_DYNAMIC_IF

Message text

The maximum number of dynamic ARP entries for interface [STRING] reached.

Variable fields

$1: Interface name.

Severity level

6

Example

The maximum number of dynamic ARP entries for interface GigabitEthernet3/0/1 reached.

Explanation

This message is sent when the maximum number of dynamic ARP entries for the specified interface is reached.

Recommended action

No action is required.

 

ARP_DYNAMIC_SLOT

Message text

(Distributed devices in standalone mode.) (Centralized IRF devices.) The maximum number of dynamic ARP entries for slot [UINT32] reached.

(Distributed devices in IRF mode.) The maximum number of dynamic ARP entries for chassis [UINT32] slot [UINT32] reached.

Variable fields

$1: Slot number. (Distributed devices in standalone mode.)

$1: Member device ID. (Centralized IRF devices.)

$2: Member device ID. (Distributed devices in IRF mode.)

$3: Slot number. (Distributed devices in IRF mode.)

Severity level

6

Example

ARP/6/ARP_DYNAMIC_SLOT: The maximum number of dynamic ARP entries for slot 2 reached.

ARP/6/ARP_DYNAMIC_SLOT: The maximum number of dynamic ARP entries for chassis 1 slot 2 reached.

Explanation

The maximum number of dynamic ARP entries for the card was reached. (Distributed devices in standalone mode.)

The maximum number of dynamic ARP entries for the member device was reached. (Centralized IRF devices.)

The maximum number of dynamic ARP entries for the card on the member device was reached. (Distributed devices in IRF mode.)

Recommended action

No action is required.

 

ARP_ENTRY_CONFLICT

Message text

The software entry for [STRING] on [STRING] and the hardware entry did not have the same [STRING].

Variable fields

$1: IP address.

$2: VPN instance name. If the ARP entry belongs to the public network, this field displays the public network.

$3: Inconsistent items:

¡     MAC address.

¡     output interface.

¡     output port.

¡     outermost layer VLAN ID.

¡     second outermost layer VLAN ID.

¡     VSI index.

¡     link ID.

Severity level

6

Example

ARP/6/ARP_ENTRY_CONFLICT: The software entry for 1.1.1.1 on the VPN a and the hardware entry did not have the same MAC address, output port, VSI index, and link ID.

ARP/6/ARP_ENTRY_CONFLICT: The software entry for 1.1.1.2 on the public  network and the hardware entry did not have the same MAC address, output port, VSI index, and link ID.

Explanation

The software entry for the specified IP address is not the same as the hardware entry. For example, they do not have the same output interface.

Recommended action

No action is required. ARP automatically refreshes the hardware entries.

 

ARP_HOST_IP_CONFLICT

Message text

The host [STRING] connected to interface [STRING] cannot communicate correctly, because it uses the same IP address as the host connected to interface [STRING].

Variable fields

$1: IP address.

$2: Interface name.

$3: Interface name.

Severity level

4

Example

ARP/4/ARP_HOST_IP_CONFLICT: The host 1.1.1.1 connected to interface GigabitEthernet1/0/1 cannot communicate correctly, because it uses the same IP address as the host connected to interface GigabitEthernet1/0/2.

Explanation

The sender IP address in a received ARP message conflicted with the IP address of a host connected to another interface.

Recommended action

Check whether the hosts that send the ARP messages are legitimate. Disconnect the illegal host from the network.

 

ARP_MAXIMUM_DEVICE

Message text

Maximum number of ARP entries on the device is reached.

Variable fields

N/A

Severity level

6

Example

ARP/6/ARP_MAXIMUM_DEVICE: Maximum number of ARP entries on the device is reached.

Explanation

This message is sent when the maximum number of all ARP entries is reached on the device.

Recommended action

No action is required.

 

ARP_RATE_EXCEEDED

Message text

The ARP packet rate ([UINT32] pps) exceeded the rate limit ([UINT32] pps) on interface [STRING] in the last [UINT32] seconds.

Variable fields

$1: ARP packet rate.

$2: ARP limit rate.

$3: Interface name.

$4: Interval time.

Severity level

4

Example

ARP/4/ARP_RATE_EXCEEDED: The ARP packet rate (100 pps) exceeded the rate limit (80 pps) on interface GigabitEthernet1/0/1 in the last 10 seconds.

Explanation

An interface received ARP messages at a higher rate than the rate limit.

Recommended action

Verify that the hosts at the sender IP addresses are legitimate.

 

ARP_SENDER_IP_INVALID

Message text

Sender IP [STRING] was not on the same network as the receiving interface [STRING].

Variable fields

$1: IP address.

$2: Interface name.

Severity level

6

Example

ARP/6/ARP_SENDER_IP_INVALID: Sender IP 192.168.10.2 was not on the same network as the receiving interface GigabitEthernet1/0/1.

Explanation

The sender IP of a received ARP message was not on the same network as the receiving interface.

Recommended action

Verify that the host at the sender IP address is legitimate.

 

ARP_SENDER_MAC_INVALID

Message text

Sender MAC [STRING] was not identical to Ethernet source MAC [STRING] on interface [STRING].

Variable fields

$1: MAC address.

$2: MAC address.

$3: Interface name.

Severity level

6

Example

ARP/6/ARP_SENDER_MAC_INVALID: Sender MAC 0000-5E14-0E00 was not identical to Ethernet source MAC 0000-5C14-0E00 on interface GigabitEthernet1/0/1.

Explanation

An interface received an ARP message. The sender MAC address in the message body was not identical to the source MAC address in the Ethernet header.

Recommended action

Verify that the host at the sender MAC address is legitimate.

 

ARP_SENDER_SMACCONFLICT

Message text

Packet was discarded because its sender MAC address was the MAC address of the receiving interface.

Interface: [STRING], sender IP: [STRING], target IP: [STRING].

Variable fields

$1: Interface name.

$2: Sender IP address.

$3: Target IP address.

Severity level

6

Example

ARP/6/ARP_SENDER_SMACCONFLICT: Packet discarded for the sender MAC address is the same as the receiving interface.

Interface: GigabitEthernet1/0/1 sender IP: 1.1.2.2 target IP: 1.1.2.1,

Explanation

The sender MAC address of a received ARP packet conflicts with the MAC address of the device.

Recommended action

No action is required.

 

ARP_SENDER_SMACCONFLICT_VSI

Message text

Packet was discarded because its sender MAC address was the MAC address of the receiving interface.

Interface: [STRING], sender IP: [STRING], target IP: [STRING],VSI index: [UINT32], link ID: [UINT32].

Variable fields

$1: Interface name.

$2: Sender IP address.

$3: Target IP address.

$4: VSI index.

$5: Link ID.

Severity level

6

Example

ARP/6/ARP_SENDER_SMACCONFLICT_VSI: Packet discarded for the sender MAC address is the same as the receiving interface.

Interface: VSI3 sender IP: 1.1.2.2 target IP: 1.1.2.1, VSI Index: 2, Link ID: 0

Explanation

The sender MAC address of a received ARP packet conflicts with the MAC address of the device. The receiving interface is a VSI interface.

Recommended action

No action is required.

 

ARP_SRC_MAC_FOUND_ATTACK

Message text

An attack from MAC [STRING] was detected on interface [STRING].

Variable fields

$1: MAC address.

$2: Interface name.

Severity level

6

Example

ARP/6/ARP_SRC_MAC_FOUND_ATTACK: An attack from MAC 0000-5E14-0E00 was detected on interface GigabitEthernet1/0/1.

Explanation

The source MAC-based ARP attack detection feature received more ARP packets from the same MAC address within 5 seconds than the specified threshold.

This message indicates the risk of attacks.

Recommended action

Verify that the host at the source MAC address is legitimate.

 

ARP_SUP_ENABLE_FAILED

Message text

Failed to enable ARP flood suppression on VSI [string].

Variable fields

$1: VSI name.

Severity level

4

Example

ARP/4/ARP_SUP_ENABLE_FAILED: -MDC=1; Failed to enable ARP flood suppression on VSI vpna.

Explanation

This message is sent when the system failed to enable ARP flood suppression for a VSI. The minimum interval between two log messages is 2 seconds. To prevent the system from failing to send the message, wait for a minimum of 2 seconds before you enable ARP flood suppression for another VSI.

Recommended action

1.     Verify that the device supports ARP flood suppression.

2.     Verify that the hardware resources are sufficient.

 

ARP_TARGET_IP_INVALID

Message text

Target IP [STRING] was not the IP of the receiving interface [STRING].

Variable fields

$1: IP address.

$2: Interface name.

Severity level

6

Example

ARP/6/ARP_TARGET_IP_INVALID: Target IP 192.168.10.2 was not the IP of the receiving interface GigabitEthernet1/0/1.

Explanation

The target IP address of a received ARP message was not the IP address of the receiving interface.

Recommended action

Verify that the host at the sender IP address is legitimate.

 

ARP_THRESHOLD_REACHED

Message text

The alarm threshold for dynamic ARP entry learning was reached on interface [STRING].

Variable fields

$1: Interface name.

Severity level

4

Example

ARP/4/ ARP_THRESHOLD_REACHED: The alarm threshold for dynamic ARP entry learning was reached on interface GigabitEthernet1/0/1.

Explanation

This message is sent when the alarm threshold for dynamic ARP learning was reached on an interface.

Recommended action

Verify that the number of learned dynamic ARP entries matches the actual number of devices in the network, and no ARP attack sources exist in the network.

 

DUPIFIP

Message text

Duplicate address [STRING] on interface [STRING], sourced from [STRING].

Variable fields

$1: IP address.

$2: Interface name.

$3: MAC Address.

Severity level

6

Example

ARP/6/DUPIFIP: Duplicate address 1.1.1.1 on interface Ethernet1/1/1, sourced from 0015-E944-A947.

Explanation

ARP detected a duplicate address.

The sender IP in the received ARP packet was being used by the receiving interface.

Recommended action

Modify the IP address configuration.

 

DUPIP

Message text

IP address [STRING] conflicted with global or imported IP address, sourced from [STRING].

Variable fields

$1: IP address.

$2: MAC Address.

Severity level

6

Example

ARP/6/DUPIP: IP address 30.1.1.1 conflicted with global or imported IP address, sourced from 0000-0000-0001.

Explanation

The sender IP address of the received ARP packet conflicted with the global or imported IP address.

Recommended action

Modify the IP address configuration.

 

DUPVRRPIP

Message text

IP address [STRING] conflicted with VRRP virtual IP address on interface [STRING], sourced from [STRING].

Variable fields

$1: IP address.

$2: Interface name.

$3: MAC address.

Severity level

6

Example

ARP/6/DUPVRRPIP: IP address 1.1.1.1 conflicted with VRRP virtual IP address on interface GigabitEthernet1/0/1, sourced from 0015-E944-A947.

Explanation

The sender IP address of the received ARP packet conflicted with the VRRP virtual IP address.

Recommended action

Modify the IP address configuration.

 

 

ATK messages

This section contains attack detection and prevention messages.

ATK_ICMP_ADDRMASK_REQ

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_REQ: IcmpType(1058)=17; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP address mask request logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_ADDRMASK_REQ_RAW

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_REQ_RAW: IcmpType(1058)=17; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP address mask requests of the same attributes, this message is sent only when the first request is received.

If log aggregation is disabled, this message is sent every time an ICMP address mask request is received.

Recommended action

No action is required.

 

ATK_ICMP_ADDRMASK_REQ_RAW_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_REQ_RAW_SZ: IcmpType(1058)=17; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP address mask requests of the same attributes, this message is sent only when the first request is received.

If log aggregation is disabled, this message is sent every time an ICMP address mask request is received.

Recommended action

No action is required.

 

ATK_ICMP_ADDRMASK_REQ_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_REQ_SZ: IcmpType(1058)=17; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP address mask request logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_ADDRMASK_RPL

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_RPL: IcmpType(1058)=18; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP address mask reply logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_ADDRMASK_RPL_RAW

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_RPL_RAW: IcmpType(1058)=18; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP address mask replies of the same attributes, this message is sent only when the first reply is received.

If log aggregation is disabled, this message is sent every time an ICMP address mask reply is received.

Recommended action

No action is required.

 

ATK_ICMP_ADDRMASK_RPL_RAW_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_RPL_RAW_SZ: IcmpType(1058)=18; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP address mask replies of the same attributes, this message is sent only when the first reply is received.

If log aggregation is disabled, this message is sent every time an ICMP address mask reply is received.

Recommended action

No action is required.

 

ATK_ICMP_ADDRMASK_RPL_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_RPL_SZ: IcmpType(1058)=18; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP address mask reply logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_ECHO_REQ

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_ECHO_REQ: IcmpType(1058)=8; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP echo request logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_ECHO_REQ_RAW

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; DstPort(1004)=[UINT16]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Destination port number.

$7: Name of the receiving VPN instance.

$8: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_ECHO_REQ_RAW: IcmpType(1058)=8; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DstPort(1004)=22; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP echo requests of the same attributes, this message is sent only when the first request is received.

If log aggregation is disabled, this message is sent every time an ICMP echo request is received.

Recommended action

No action is required.

 

ATK_ICMP_ECHO_REQ_RAW_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; DstPort(1004)=[UINT16]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Destination port number.

$7: Name of the receiving VPN instance.

$8: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_ECHO_REQ_RAW_SZ: IcmpType(1058)=8; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DstPort(1004)=22; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP echo requests of the same attributes, this message is sent only when the first request is received.

If log aggregation is disabled, this message is sent every time an ICMP echo request is received.

Recommended action

No action is required.

 

ATK_ICMP_ECHO_REQ_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_ECHO_REQ_SZ: IcmpType(1058)=8; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP echo request logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_ECHO_RPL

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_ECHO_RPL: IcmpType(1058)=0; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP echo reply logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_ECHO_RPL_RAW

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_ECHO_RPL_RAW: IcmpType(1058)=0; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP echo replies of the same attributes, this message is sent only when the first reply is received.

If log aggregation is disabled, this message is sent every time an ICMP echo reply is received.

Recommended action

No action is required.

 

ATK_ICMP_ECHO_RPL_RAW_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_ECHO_RPL_RAW_SZ: IcmpType(1058)=0; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP echo replies of the same attributes, this message is sent only when the first reply is received.

If log aggregation is disabled, this message is sent every time an ICMP echo reply is received.

Recommended action

No action is required.

 

ATK_ICMP_ECHO_RPL_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_ECHO_RPL_SZ: IcmpType(1058)=0; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP echo reply logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_FLOOD

Message text

RcvIfName(1023)=[STRING]; DstIPAddr(1007)=[IPADDR]; DstPort(1008)=[UINT16]; RcvVPNInstance(1041)=[STRING]; UpperLimit(1048)=[UINT32]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING].

Variable fields

$1: Receiving interface name.

$2: Destination IP address.

$3: Destination port number.

$4: Name of the receiving VPN instance.

$5: Rate limit.

$6: Actions against the attack.

$7: Start time of the attack.

Severity level

3

Example

ATK/3/ATK_ICMP_FLOOD: RcvIfName(1023)=Ethernet0/0/2; DstIPAddr(1007)=6.1.1.5; DstPort(1008)=22; RcvVPNInstance(1041)=--; UpperLimit(1048)=10; Action(1049)=logging; BeginTime_c(1011)=20131009093351.

Explanation

This message is sent when the number of ICMP packets sent to a destination per second exceeds the rate limit.

Recommended action

No action is required.

 

ATK_ICMP_FLOOD_SZ

Message text

SrcZoneName(1025)=[STRING]; DstIPAddr(1007)=[IPADDR]; DstPort(1008)=[UINT16]; RcvVPNInstance(1041)=[STRING]; UpperLimit(1048)=[UINT32]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING].

Variable fields

$1: Source security zone name.

$2: Destination IP address.

$3: Destination port number.

$4: Name of the receiving VPN instance.

$5: Rate limit.

$6: Actions against the attack.

$7: Start time of the attack.

Severity level

3

Example

ATK/3/ATK_ICMP_FLOOD_SZ: SrcZoneName(1025)=Trust; DstIPAddr(1007)=6.1.1.5; DstPort(1008)=22; RcvVPNInstance(1041)=--; UpperLimit(1048)=10; Action(1049)=logging; BeginTime_c(1011)=20131009093351.

Explanation

This message is sent when the number of ICMP packets sent to a destination per second exceeds the rate limit.

Recommended action

No action is required.

 

ATK_ICMP_INFO_REQ

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_INFO_REQ: IcmpType(1058)=15; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP information request logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_INFO_REQ_RAW

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_INFO_REQ_RAW: IcmpType(1058)=15; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP information requests of the same attributes, this message is sent only when the first request is received.

If log aggregation is disabled, this message is sent every time an ICMP information request is received.

Recommended action

No action is required.

 

ATK_ICMP_INFO_REQ_RAW_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_INFO_REQ_RAW_SZ: IcmpType(1058)=15; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP information requests of the same attributes, this message is sent only when the first request is received.

If log aggregation is disabled, this message is sent every time an ICMP information request is received.

Recommended action

No action is required.

 

ATK_ICMP_INFO_REQ_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_INFO_REQ_SZ: IcmpType(1058)=15; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP information request logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_INFO_RPL

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_INFO_RPL: IcmpType(1058)=16; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP information reply logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_INFO_RPL_RAW

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_INFO_RPL_RAW: IcmpType(1058)=16; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP information replies of the same attributes, this message is sent only when the first reply is received.

If log aggregation is disabled, this message is sent every time an ICMP information reply is received.

Recommended action

No action is required.

 

ATK_ICMP_INFO_RPL_RAW_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_INFO_RPL_RAW_SZ: IcmpType(1058)=16; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP information replies of the same attributes, this message is sent only when the first reply is received.

If log aggregation is disabled, this message is sent every time an ICMP information reply is received.

Recommended action

No action is required.

 

ATK_ICMP_INFO_RPL_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_INFO_RPL_SZ: IcmpType(1058)=16; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP information reply logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_LARGE

Message text

RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: Receiving interface name.

$2: Source IP address.

$3: IP address of the peer DS-Lite tunnel interface.

$4: Destination IP address.

$5: Name of the receiving VPN instance.

$6: Actions against the attack.

$7: Start time of the attack.

$8: End time of the attack.

$9: Attack times.

Severity level

3

Example

ATK/3/ATK_ICMP_LARGE: RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011074913; EndTime_c(1012)=20131011075413; AtkTimes(1050)=2.

Explanation

This message is sent when large ICMP packet logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_LARGE_RAW

Message text

RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: Receiving interface name.

$2: Source IP address.

$3: IP address of the peer DS-Lite tunnel interface.

$4: Destination IP address.

$5: Name of the receiving VPN instance.

$6: Actions against the attack.

Severity level

3

Example

ATK/3/ATK_ICMP_LARGE_RAW: RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for large ICMP packets of the same attributes, this message is sent only when the first packet is received.

If log aggregation is disabled, this message is sent every time a large ICMP packet is received.

Recommended action

No action is required.

 

ATK_ICMP_LARGE_RAW_SZ

Message text

SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: Source security zone name.

$2: Source IP address.

$3: IP address of the peer DS-Lite tunnel interface.

$4: Destination IP address.

$5: Name of the receiving VPN instance.

$6: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_LARGE_RAW_SZ: SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for large ICMP packets of the same attributes, this message is sent only when the first packet is received.

If log aggregation is disabled, this message is sent every time a large ICMP packet is received.

Recommended action

No action is required.

 

ATK_ICMP_LARGE_SZ

Message text

SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: Source security zone name.

$2: Source IP address.

$3: IP address of the peer DS-Lite tunnel interface.

$4: Destination IP address.

$5: Name of the receiving VPN instance.

$6: Actions against the attack.

$7: Start time of the attack.

$8: End time of the attack.

$9: Attack times.

Severity level

3

Example

ATK/3/ATK_ICMP_LARGE_SZ: SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011074913; EndTime_c(1012)=20131011075413; AtkTimes(1050)=2.

Explanation

This message is sent when large ICMP packet logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_PARAPROBLEM

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_PARAPROBLEM: IcmpType(1058)=12; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP parameter problem logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_PARAPROBLEM_RAW

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_PARAPROBLEM_RAW: IcmpType(1058)=12; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP parameter problem packets of the same attributes, this message is sent only when the first packet is received.

If log aggregation is disabled, this message is sent every time an ICMP parameter problem packet is received.

Recommended action

No action is required.

 

ATK_ICMP_PARAPROBLEM_RAW_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_PARAPROBLEM_RAW_SZ: IcmpType(1058)=12; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP parameter problem packets of the same attributes, this message is sent only when the first packet is received.

If log aggregation is disabled, this message is sent every time an ICMP parameter problem packet is received.

Recommended action

No action is required.

 

ATK_ICMP_PARAPROBLEM_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_PARAPROBLEM_SZ: IcmpType(1058)=12; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP parameter problem logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_PINGOFDEATH

Message text

RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: Receiving interface name.

$2: Source IP address.

$3: IP address of the peer DS-Lite tunnel interface.

$4: Destination IP address.

$5: Name of the receiving VPN instance.

$6: Actions against the attack.

$7: Start time of the attack.

$8: End time of the attack.

$9: Attack times.

Severity level

3

Example

ATK/3/ATK_ICMP_PINGOFDEATH: RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011074913; EndTime_c(1012)=20131011075413; AtkTimes(1050)=2.

Explanation

This message is sent when logs are aggregated for ICMP packets larger than 65535 bytes with the MF flag set to 0.

Recommended action

No action is required.

 

ATK_ICMP_PINGOFDEATH_RAW

Message text

RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: Receiving interface name.

$2: Source IP address.

$3: IP address of the peer DS-Lite tunnel interface.

$4: Destination IP address.

$5: Name of the receiving VPN instance.

$6: Actions against the attack.

Severity level

3

Example

ATK/3/ATK_ICMP_PINGOFDEATH_RAW: RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

This message is for the ping of death attack. The attack uses ICMP packets larger than 65535 bytes with the MF flag set to 0.

If log aggregation is enabled, for packets of the same attributes, this message is sent only when the first packet is received.

If log aggregation is disabled, this message is sent every time a packet is received.

Recommended action

No action is required.

 

ATK_ICMP_PINGOFDEATH_RAW_SZ

Message text

SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: Source security zone name.

$2: Source IP address.

$3: IP address of the peer DS-Lite tunnel interface.

$4: Destination IP address.

$5: Name of the receiving VPN instance.

$6: Actions against the attack.

Severity level

3

Example

ATK/3/ATK_ICMP_PINGOFDEATH_RAW_SZ: SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

This message is for the ping of death attack. The attack uses ICMP packets larger than 65535 bytes with the MF flag set to 0.

If log aggregation is enabled, for packets of the same attributes, this message is sent only when the first packet is received.

If log aggregation is disabled, this message is sent every time a packet is received.

Recommended action

No action is required.

 

ATK_ICMP_PINGOFDEATH_SZ

Message text

SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: Source security zone name.

$2: Source IP address.

$3: IP address of the peer DS-Lite tunnel interface.

$4: Destination IP address.

$5: Name of the receiving VPN instance.

$6: Actions against the attack.

$7: Start time of the attack.

$8: End time of the attack.

$9: Attack times.

Severity level

3

Example

ATK/3/ATK_ICMP_PINGOFDEATH_SZ: SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011074913; EndTime_c(1012)=20131011075413; AtkTimes(1050)=2.

Explanation

This message is sent when logs are aggregated for ICMP packets larger than 65535 bytes with the MF flag set to 0.

Recommended action

No action is required.

 

ATK_ICMP_REDIRECT

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_REDIRECT: IcmpType(1058)=5; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP redirect logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_REDIRECT_RAW

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_REDIRECT_RAW: IcmpType(1058)=5; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP redirect packets of the same attributes, this message is sent only when the first packet is received.

If log aggregation is disabled, this message is sent every time an ICMP redirect packet is received.

Recommended action

No action is required.

 

ATK_ICMP_REDIRECT_RAW_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_REDIRECT_RAW_SZ: IcmpType(1058)=5; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP redirect packets of the same attributes, this message is sent only when the first packet is received.

If log aggregation is disabled, this message is sent every time an ICMP redirect packet is received.

Recommended action

No action is required.

 

ATK_ICMP_REDIRECT_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_REDIRECT_SZ: IcmpType(1058)=5; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP redirect logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_SMURF

Message text

RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: Receiving interface name.

$2: Source IP address.

$3: IP address of the peer DS-Lite tunnel interface.

$4: Destination IP address.

$5: Name of the receiving VPN instance.

$6: Actions against the attack.

$7: Start time of the attack.

$8: End time of the attack.

$9: Attack times.

Severity level

3

Example

ATK/3/ATK_ICMP_SMURF: RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011074913; EndTime_c(1012)=20131011075413; AtkTimes(1050)=2.

Explanation

This message is sent when logs are aggregated for ICMP echo requests whose destination IP address is one of the following addresses:

·     A broadcast or network address of A, B, or C class.

·     An IP address of D or E class.

·     The broadcast or network address of the network where the receiving interface resides.

Recommended action

No action is required.

 

ATK_ICMP_SMURF_RAW

Message text

RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: Receiving interface name.

$2: Source IP address.

$3: IP address of the peer DS-Lite tunnel interface.

$4: Destination IP address.

$5: Name of the receiving VPN instance.

$6: Actions against the attack.

Severity level

3

Example

ATK/3/ATK_ICMP_SMURF_RAW: RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

This message is for the smurf attack. The attack uses ICMP echo requests with the destination IP address being one of the following addresses:

·     A broadcast or network address of A, B, or C class.

·     An IP address of D or E class.

·     The broadcast or network address of the network where the receiving interface resides.

If log aggregation is enabled, for requests of the same attributes, this message is sent only when the first request is received.

If log aggregation is disabled, this message is sent every time a request is received.

Recommended action

No action is required.

 

ATK_ICMP_SMURF_RAW_SZ

Message text

SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: Source security zone name.

$2: Source IP address.

$3: IP address of the peer DS-Lite tunnel interface.

$4: Destination IP address.

$5: Name of the receiving VPN instance.

$6: Actions against the attack.

Severity level

3

Example

ATK/3/ATK_ICMP_SMURF_RAW_SZ: SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

This message is for the smurf attack. The attack uses ICMP echo requests with the destination IP address being one of the following addresses:

·     A broadcast or network address of A, B, or C class.

·     An IP address of D or E class.

·     The broadcast or network address of the network where the receiving interface resides.

If log aggregation is enabled, for requests of the same attributes, this message is sent only when the first request is received.

If log aggregation is disabled, this message is sent every time a request is received.

Recommended action

No action is required.

 

ATK_ICMP_SMURF_SZ

Message text

SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: Source security zone name.

$2: Source IP address.

$3: IP address of the peer DS-Lite tunnel interface.

$4: Destination IP address.

$5: Name of the receiving VPN instance.

$6: Actions against the attack.

$7: Start time of the attack.

$8: End time of the attack.

$9: Attack times.

Severity level

3

Example

ATK/3/ATK_ICMP_SMURF_SZ: SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011074913; EndTime_c(1012)=20131011075413; AtkTimes(1050)=2.

Explanation

This message is sent when logs are aggregated for ICMP echo requests whose destination IP address is one of the following addresses:

·     A broadcast or network address of A, B, or C class.

·     An IP address of D or E class.

·     The broadcast or network address of the network where the receiving interface resides.

Recommended action

No action is required.

 

ATK_ICMP_SOURCEQUENCH

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_SOURCEQUENCH: IcmpType(1058)=4; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP source quench logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_SOURCEQUENCH_RAW

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_SOURCEQUENCH_RAW: IcmpType(1058)=4; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP source quench packets of the same attributes, this message is sent only when the first packet is received.

If log aggregation is disabled, this message is sent every time an ICMP source quench packet is received.

Recommended action

No action is required.

 

ATK_ICMP_SOURCEQUENCH_RAW_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_SOURCEQUENCH_RAW_SZ: IcmpType(1058)=4; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP source quench packets of the same attributes, this message is sent only when the first packet is received.

If log aggregation is disabled, this message is sent every time an ICMP source quench packet is received.

Recommended action

No action is required.

 

ATK_ICMP_SOURCEQUENCH_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_SOURCEQUENCH_SZ: IcmpType(1058)=4; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP source quench logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_TIMEEXCEED

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_TIMEEXCEED: IcmpType(1058)=11; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation