H3C S6860 Switch Series System Log Messages Reference-6W100

HomeSupportResource CenterSwitchesH3C S6860 Switch SeriesH3C S6860 Switch SeriesTechnical DocumentsMaintainMessage ReferencesH3C S6860 Switch Series System Log Messages Reference-6W100

 

H3C S6860 Switch Series

System Log Messages Reference

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Document version: 6W100-20180605

 

H3C_彩色.emf

 


Contents

Introduction· 1

System log message format 1

Managing and obtaining system log messages· 3

Obtaining log messages from the console terminal 3

Obtaining log messages from the log buffer 3

Obtaining log messages from a monitor terminal 4

Obtaining log messages from the log file· 4

Obtaining log messages from a log host 4

Software module list 4

Using this document 8

AAA messages· 8

AAA_FAILURE· 9

AAA_LAUNCH·· 9

AAA_SUCCESS· 10

ACL messages· 10

ACL_ACCELERATE_NO_RES· 10

ACL_ACCELERATE_NONCONTIGUOUSMASK· 10

ACL_ACCELERATE_NOT_SUPPORT· 11

ACL_ACCELERATE_NOT_SUPPORTHOPBYHOP· 11

ACL_ACCELERATE_NOT_SUPPORTMULTITCPFLAG·· 11

ACL_ACCELERATE_UNK_ERR·· 12

ACL_IPV6_STATIS_INFO·· 12

ACL_NO_MEM·· 12

ACL_STATIS_INFO·· 13

ANCP messages· 13

ANCP_INVALID_PACKET· 13

APMGR messages· 13

APMGR_AC_MEM_ALERT· 14

APMGR_ADD_AP_FAIL· 14

APMGR_ADDBAC_INFO·· 14

APMGR_AP_OFFLINE· 15

APMGR_AP_ONLINE· 15

APMGR_CWC_IMG_DOWNLOAD_COMPLETE· 15

APMGR_CWC_IMG_DOWNLOAD_START· 16

APMGR_CWC_IMG_NO_ENOUGH_SPACE· 16

APMGR_CWC_LOCAL_AC_DOWN·· 17

APMGR_CWC_LOCAL_AC_UP· 17

APMGR_CWC_REBOOT· 18

APMGR_CWC_RUN_DOWNLOAD_COMPLETE· 18

APMGR_CWC_RUN_DOWNLOAD_START· 18

APMGR_CWC_RUN_NO_ENOUGH_SPACE· 19

APMGR_CWC_TUNNEL_DOWN·· 19

APMGR_CWC_TUNNEL_UP· 20

APMGR_CWS_IMG_DOWNLOAD_COMPLETE· 20

APMGR_CWS_IMG_DOWNLOAD_START· 20

APMGR_CWS_LOCAL_AC_DOWN·· 21

APMGR_CWS_LOCAL_AC_UP· 21

APMGR_CWS_RUN_DOWNLOAD_COMPLETE· 22

APMGR_CWS_RUN_DOWNLOAD_START· 22

APMGR_CWS_TUNNEL_DOWN·· 23

APMGR_CWS_TUNNEL_UP· 23

APMGR_DELBAC_INFO·· 24

APMGR_LOCAL_AC_OFFLINE· 24

APMGR_LOCAL_AC_ONLINE· 24

ARP messages· 24

ARP_ACTIVE_ACK_NO_REPLY· 25

ARP_ACTIVE_ACK_NOREQUESTED_REPLY· 25

ARP_BINDRULETOHW_FAILED·· 26

ARP_DETECTION_LOG·· 26

ARP_DUPLICATE_IPADDR_DETECT· 27

ARP_DYNAMIC·· 27

ARP_DYNAMIC_IF· 28

ARP_DYNAMIC_SLOT· 28

ARP_ENTRY_CONFLICT· 29

ARP_HOST_IP_CONFLICT· 29

ARP_MAXIMUM_DEVICE· 30

ARP_LOCALPROXY_ENABLE_FAILED·· 30

ARP_RATE_EXCEEDED·· 30

ARP_SENDER_IP_INVALID·· 31

ARP_SENDER_MAC_INVALID·· 31

ARP_SENDER_SMACCONFLICT· 32

ARP_SENDER_SMACCONFLICT_VSI 32

ARP_SRC_MAC_FOUND_ATTACK· 33

ARP_SUP_ENABLE_FAILED·· 33

ARP_TARGET_IP_INVALID·· 33

ARP_THRESHOLD_REACHED·· 34

DUPIFIP· 34

DUPIP· 34

DUPVRRPIP· 35

ATK messages· 35

ATK_ICMP_ADDRMASK_REQ·· 35

ATK_ICMP_ADDRMASK_REQ_RAW·· 36

ATK_ICMP_ADDRMASK_REQ_RAW_SZ· 37

ATK_ICMP_ADDRMASK_REQ_SZ· 38

ATK_ICMP_ADDRMASK_RPL· 39

ATK_ICMP_ADDRMASK_RPL_RAW·· 40

ATK_ICMP_ADDRMASK_RPL_RAW_SZ· 41

ATK_ICMP_ADDRMASK_RPL_SZ· 42

ATK_ICMP_ECHO_REQ·· 43

ATK_ICMP_ECHO_REQ_RAW·· 44

ATK_ICMP_ECHO_REQ_RAW_SZ· 45

ATK_ICMP_ECHO_REQ_SZ· 46

ATK_ICMP_ECHO_RPL· 47

ATK_ICMP_ECHO_RPL_RAW·· 48

ATK_ICMP_ECHO_RPL_RAW_SZ· 49

ATK_ICMP_ECHO_RPL_SZ· 50

ATK_ICMP_FLOOD·· 51

ATK_ICMP_FLOOD_SZ· 51

ATK_ICMP_INFO_REQ·· 52

ATK_ICMP_INFO_REQ_RAW·· 53

ATK_ICMP_INFO_REQ_RAW_SZ· 54

ATK_ICMP_INFO_REQ_SZ· 55

ATK_ICMP_INFO_RPL· 56

ATK_ICMP_INFO_RPL_RAW·· 57

ATK_ICMP_INFO_RPL_RAW_SZ· 58

ATK_ICMP_INFO_RPL_SZ· 59

ATK_ICMP_LARGE· 60

ATK_ICMP_LARGE_RAW·· 60

ATK_ICMP_LARGE_RAW_SZ· 61

ATK_ICMP_LARGE_SZ· 61

ATK_ICMP_PARAPROBLEM·· 62

ATK_ICMP_PARAPROBLEM_RAW·· 63

ATK_ICMP_PARAPROBLEM_RAW_SZ· 64

ATK_ICMP_PARAPROBLEM_SZ· 65

ATK_ICMP_PINGOFDEATH·· 66

ATK_ICMP_PINGOFDEATH_RAW·· 67

ATK_ICMP_PINGOFDEATH_RAW_SZ· 67

ATK_ICMP_PINGOFDEATH_SZ· 68

ATK_ICMP_REDIRECT· 69

ATK_ICMP_REDIRECT_RAW·· 70

ATK_ICMP_REDIRECT_RAW_SZ· 71

ATK_ICMP_REDIRECT_SZ· 72

ATK_ICMP_SMURF· 73

ATK_ICMP_SMURF_RAW·· 74

ATK_ICMP_SMURF_RAW_SZ· 75

ATK_ICMP_SMURF_SZ· 76

ATK_ICMP_SOURCEQUENCH·· 77

ATK_ICMP_SOURCEQUENCH_RAW·· 78

ATK_ICMP_SOURCEQUENCH_RAW_SZ· 79

ATK_ICMP_SOURCEQUENCH_SZ· 80

ATK_ICMP_TIMEEXCEED·· 81

ATK_ICMP_TIMEEXCEED_RAW·· 82

ATK_ICMP_TIMEEXCEED_RAW_SZ· 83

ATK_ICMP_TIMEEXCEED_SZ· 84

ATK_ICMP_TRACEROUTE· 85

ATK_ICMP_TRACEROUTE_RAW·· 86

ATK_ICMP_TRACEROUTE_RAW_SZ· 86

ATK_ICMP_TRACEROUTE_SZ· 87

ATK_ICMP_TSTAMP_REQ·· 88

ATK_ICMP_TSTAMP_REQ_RAW·· 89

ATK_ICMP_TSTAMP_REQ_RAW_SZ· 90

ATK_ICMP_TSTAMP_REQ_SZ· 91

ATK_ICMP_TSTAMP_RPL· 92

ATK_ICMP_TSTAMP_RPL_RAW·· 93

ATK_ICMP_TSTAMP_RPL_RAW_SZ· 94

ATK_ICMP_TSTAMP_RPL_SZ· 95

ATK_ICMP_TYPE· 96

ATK_ICMP_TYPE_RAW·· 97

ATK_ICMP_TYPE_RAW_SZ· 98

ATK_ICMP_TYPE_SZ· 99

ATK_ICMP_UNREACHABLE· 100

ATK_ICMP_UNREACHABLE_RAW·· 101

ATK_ICMP_UNREACHABLE_RAW_SZ· 102

ATK_ICMP_UNREACHABLE_SZ· 103

ATK_ICMPV6_DEST_UNREACH·· 104

ATK_ICMPV6_DEST_UNREACH_RAW·· 105

ATK_ICMPV6_DEST_UNREACH_RAW_SZ· 105

ATK_ICMPV6_DEST_UNREACH_SZ· 106

ATK_ICMPV6_ECHO_REQ·· 107

ATK_ICMPV6_ECHO_REQ_RAW·· 108

ATK_ICMPV6_ECHO_REQ_RAW_SZ· 108

ATK_ICMPV6_ECHO_REQ_SZ· 109

ATK_ICMPV6_ECHO_RPL· 110

ATK_ICMPV6_ECHO_RPL_RAW·· 111

ATK_ICMPV6_ECHO_RPL_RAW_SZ· 111

ATK_ICMPV6_ECHO_RPL_SZ· 112

ATK_ICMPV6_FLOOD·· 113

ATK_ICMPV6_FLOOD_SZ· 113

ATK_ICMPV6_GROUPQUERY· 114

ATK_ICMPV6_GROUPQUERY_RAW·· 115

ATK_ICMPV6_GROUPQUERY_RAW_SZ· 115

ATK_ICMPV6_GROUPQUERY_SZ· 116

ATK_ICMPV6_GROUPREDUCTION·· 117

ATK_ICMPV6_GROUPREDUCTION_RAW·· 118

ATK_ICMPV6_GROUPREDUCTION_RAW_SZ· 118

ATK_ICMPV6_GROUPREDUCTION_SZ· 119

ATK_ICMPV6_GROUPREPORT· 120

ATK_ICMPV6_GROUPREPORT_RAW·· 121

ATK_ICMPV6_GROUPREPORT_RAW_SZ· 121

ATK_ICMPV6_GROUPREPORT_SZ· 122

ATK_ICMPV6_LARGE· 123

ATK_ICMPV6_LARGE_RAW·· 123

ATK_ICMPV6_LARGE_RAW_SZ· 124

ATK_ICMPV6_LARGE_SZ· 124

ATK_ICMPV6_PACKETTOOBIG·· 125

ATK_ICMPV6_PACKETTOOBIG_RAW·· 126

ATK_ICMPV6_PACKETTOOBIG_RAW_SZ· 126

ATK_ICMPV6_PACKETTOOBIG_SZ· 127

ATK_ICMPV6_PARAPROBLEM·· 128

ATK_ICMPV6_PARAPROBLEM_RAW·· 129

ATK_ICMPV6_PARAPROBLEM_RAW_SZ· 129

ATK_ICMPV6_PARAPROBLEM_SZ· 130

ATK_ICMPV6_TIMEEXCEED·· 131

ATK_ICMPV6_TIMEEXCEED_RAW·· 132

ATK_ICMPV6_TIMEEXCEED_RAW_SZ· 132

ATK_ICMPV6_TIMEEXCEED_SZ· 133

ATK_ICMPV6_TRACEROUTE· 134

ATK_ICMPV6_TRACEROUTE_RAW·· 135

ATK_ICMPV6_TRACEROUTE_RAW_SZ· 136

ATK_ICMPV6_TRACEROUTE_SZ· 137

ATK_ICMPV6_TYPE· 138

ATK_ICMPV6_TYPE _RAW_SZ· 139

ATK_ICMPV6_TYPE_RAW·· 139

ATK_ICMPV6_TYPE_SZ· 140

ATK_IP_OPTION·· 141

ATK_IP_OPTION_RAW·· 142

ATK_IP_OPTION_RAW_SZ· 143

ATK_IP_OPTION_SZ· 144

ATK_IP4_ACK_FLOOD·· 145

ATK_IP4_ACK_FLOOD_SZ· 145

ATK_IP4_DIS_PORTSCAN·· 146

ATK_IP4_DIS_PORTSCAN_SZ· 146

ATK_IP4_DNS_FLOOD·· 147

ATK_IP4_DNS_FLOOD_SZ· 147

ATK_IP4_FIN_FLOOD·· 148

ATK_IP4_FIN_FLOOD_SZ· 148

ATK_IP4_FRAGMENT· 149

ATK_IP4_FRAGMENT_RAW·· 150

ATK_IP4_FRAGMENT_RAW_SZ· 151

ATK_IP4_FRAGMENT_SZ· 152

ATK_IP4_HTTP_FLOOD·· 153

ATK_IP4_HTTP_FLOOD_SZ· 153

ATK_IP4_IMPOSSIBLE· 154

ATK_IP4_IMPOSSIBLE_RAW·· 155

ATK_IP4_IMPOSSIBLE_RAW_SZ· 156

ATK_IP4_IMPOSSIBLE_SZ· 157

ATK_IP4_IPSWEEP· 158

ATK_IP4_IPSWEEP_SZ· 158

ATK_IP4_PORTSCAN·· 159

ATK_IP4_PORTSCAN_SZ· 159

ATK_IP4_RST_FLOOD·· 160

ATK_IP4_RST_FLOOD_SZ· 160

ATK_IP4_SYN_FLOOD·· 161

ATK_IP4_SYN_FLOOD_SZ· 161

ATK_IP4_SYNACK_FLOOD·· 162

ATK_IP4_SYNACK_FLOOD_SZ· 162

ATK_IP4_TCP_ALLFLAGS· 163

ATK_IP4_TCP_ALLFLAGS_RAW·· 164

ATK_IP4_TCP_ALLFLAGS_RAW_SZ· 164

ATK_IP4_TCP_ALLFLAGS_SZ· 165

ATK_IP4_TCP_FINONLY· 166

ATK_IP4_TCP_FINONLY_RAW·· 167

ATK_IP4_TCP_FINONLY_RAW_SZ· 167

ATK_IP4_TCP_FINONLY_SZ· 168

ATK_IP4_TCP_INVALIDFLAGS· 169

ATK_IP4_TCP_INVALIDFLAGS_RAW·· 170

ATK_IP4_TCP_INVALIDFLAGS_RAW_SZ· 171

ATK_IP4_TCP_INVALIDFLAGS_SZ· 172

ATK_IP4_TCP_LAND·· 173

ATK_IP4_TCP_LAND_RAW·· 174

ATK_IP4_TCP_LAND_RAW_SZ· 174

ATK_IP4_TCP_LAND_SZ· 175

ATK_IP4_TCP_NULLFLAG·· 176

ATK_IP4_TCP_NULLFLAG_RAW·· 177

ATK_IP4_TCP_NULLFLAG_RAW_SZ· 177

ATK_IP4_TCP_NULLFLAG_SZ· 178

ATK_IP4_TCP_SYNFIN·· 179

ATK_IP4_TCP_SYNFIN_RAW·· 180

ATK_IP4_TCP_SYNFIN_RAW_SZ· 180

ATK_IP4_TCP_SYNFIN_SZ· 181

ATK_IP4_TCP_WINNUKE· 182

ATK_IP4_TCP_WINNUKE_RAW·· 183

ATK_IP4_TCP_WINNUKE_RAW_SZ· 184

ATK_IP4_TCP_WINNUKE_SZ· 185

ATK_IP4_TEARDROP· 186

ATK_IP4_TEARDROP_RAW·· 187

ATK_IP4_TEARDROP_RAW_SZ· 188

ATK_IP4_TEARDROP_SZ· 189

ATK_IP4_TINY_FRAGMENT· 190

ATK_IP4_TINY_FRAGMENT_RAW·· 191

ATK_IP4_TINY_FRAGMENT_RAW_SZ· 192

ATK_IP4_TINY_FRAGMENT_SZ· 193

ATK_IP4_UDP_BOMB· 194

ATK_IP4_UDP_BOMB_RAW·· 195

ATK_IP4_UDP_BOMB_RAW_SZ· 196

ATK_IP4_UDP_BOMB_SZ· 197

ATK_IP4_UDP_FLOOD·· 198

ATK_IP4_UDP_FLOOD_SZ· 198

ATK_IP4_UDP_FRAGGLE· 199

ATK_IP4_UDP_FRAGGLE_RAW·· 200

ATK_IP4_UDP_FRAGGLE_RAW_SZ· 200

ATK_IP4_UDP_FRAGGLE_SZ· 201

ATK_IP4_UDP_SNORK· 202

ATK_IP4_UDP_SNORK_RAW·· 203

ATK_IP4_UDP_SNORK_RAW_SZ· 203

ATK_IP4_UDP_SNORK_SZ· 204

ATK_IP6_ACK_FLOOD·· 205

ATK_IP6_ACK_FLOOD_SZ· 205

ATK_IP6_DIS_PORTSCAN·· 206

ATK_IP6_DIS_PORTSCAN_SZ· 206

ATK_IP6_DNS_FLOOD·· 207

ATK_IP6_DNS_FLOOD_SZ· 207

ATK_IP6_FIN_FLOOD·· 208

ATK_IP6_FIN_FLOOD_SZ· 208

ATK_IP6_FRAGMENT· 209

ATK_IP6_FRAGMENT_RAW·· 210

ATK_IP6_FRAGMENT_RAW_SZ· 211

ATK_IP6_FRAGMENT_SZ· 212

ATK_IP6_HTTP_FLOOD·· 213

ATK_IP6_HTTP_FLOOD_SZ· 213

ATK_IP6_IMPOSSIBLE· 214

ATK_IP6_IMPOSSIBLE_RAW·· 215

ATK_IP6_IMPOSSIBLE_RAW_SZ· 216

ATK_IP6_IMPOSSIBLE_SZ· 217

ATK_IP6_IPSWEEP· 217

ATK_IP6_IPSWEEP_SZ· 218

ATK_IP6_PORTSCAN·· 218

ATK_IP6_PORTSCAN_SZ· 219

ATK_IP6_RST_FLOOD·· 219

ATK_IP6_RST_FLOOD_SZ· 220

ATK_IP6_SYN_FLOOD·· 220

ATK_IP6_SYN_FLOOD_SZ· 221

ATK_IP6_SYNACK_FLOOD·· 221

ATK_IP6_SYNACK_FLOOD_SZ· 222

ATK_IP6_TCP_ALLFLAGS· 222

ATK_IP6_TCP_ALLFLAGS_RAW·· 223

ATK_IP6_TCP_ALLFLAGS_RAW_SZ· 223

ATK_IP6_TCP_ALLFLAGS_SZ· 224

ATK_IP6_TCP_FINONLY· 225

ATK_IP6_TCP_FINONLY_RAW·· 225

ATK_IP6_TCP_FINONLY_RAW_SZ· 226

ATK_IP6_TCP_FINONLY_SZ· 226

ATK_IP6_TCP_INVALIDFLAGS· 227

ATK_IP6_TCP_INVALIDFLAGS_RAW·· 228

ATK_IP6_TCP_INVALIDFLAGS_RAW_SZ· 229

ATK_IP6_TCP_INVALIDFLAGS_SZ· 230

ATK_IP6_TCP_LAND·· 231

ATK_IP6_TCP_LAND_RAW·· 231

ATK_IP6_TCP_LAND_RAW_SZ· 232

ATK_IP6_TCP_LAND_SZ· 232

ATK_IP6_TCP_NULLFLAG·· 233

ATK_IP6_TCP_NULLFLAG_RAW·· 233

ATK_IP6_TCP_NULLFLAG_RAW_SZ· 234

ATK_IP6_TCP_NULLFLAG_SZ· 234

ATK_IP6_TCP_SYNFIN·· 235

ATK_IP6_TCP_SYNFIN_RAW·· 235

ATK_IP6_TCP_SYNFIN_RAW_SZ· 236

ATK_IP6_TCP_SYNFIN_SZ· 236

ATK_IP6_TCP_WINNUKE· 237

ATK_IP6_TCP_WINNUKE_RAW·· 237

ATK_IP6_TCP_WINNUKE_RAW_SZ· 238

ATK_IP6_TCP_WINNUKE_SZ· 238

ATK_IP6_UDP_FLOOD·· 239

ATK_IP6_UDP_FLOOD_SZ· 239

ATK_IP6_UDP_FRAGGLE· 240

ATK_IP6_UDP_FRAGGLE_RAW·· 240

ATK_IP6_UDP_FRAGGLE_RAW_SZ· 241

ATK_IP6_UDP_FRAGGLE_SZ· 241

ATK_IP6_UDP_SNORK· 242

ATK_IP6_UDP_SNORK_RAW·· 242

ATK_IP6_UDP_SNORK_RAW_SZ· 243

ATK_IP6_UDP_SNORK_SZ· 243

ATK_IPOPT_ABNORMAL· 244

ATK_IPOPT_ABNORMAL_RAW·· 245

ATK_IPOPT_ABNORMAL_RAW_SZ· 246

ATK_IPOPT_ABNORMAL_SZ· 247

ATK_IPOPT_LOOSESRCROUTE· 248

ATK_IPOPT_LOOSESRCROUTE_RAW·· 249

ATK_IPOPT_LOOSESRCROUTE_RAW_SZ· 250

ATK_IPOPT_LOOSESRCROUTE_SZ· 251

ATK_IPOPT_RECORDROUTE· 252

ATK_IPOPT_RECORDROUTE_RAW·· 253

ATK_IPOPT_RECORDROUTE_RAW_SZ· 254

ATK_IPOPT_RECORDROUTE_SZ· 255

ATK_IPOPT_ROUTEALERT· 256

ATK_IPOPT_ROUTEALERT_RAW·· 257

ATK_IPOPT_ROUTEALERT_RAW_SZ· 258

ATK_IPOPT_ROUTEALERT_SZ· 259

ATK_IPOPT_SECURITY· 260

ATK_IPOPT_SECURITY_RAW·· 261

ATK_IPOPT_SECURITY_RAW_SZ· 262

ATK_IPOPT_SECURITY_SZ· 263

ATK_IPOPT_STREAMID·· 264

ATK_IPOPT_STREAMID_RAW·· 265

ATK_IPOPT_STREAMID_RAW_SZ· 266

ATK_IPOPT_STREAMID_SZ· 267

ATK_IPOPT_STRICTSRCROUTE· 268

ATK_IPOPT_STRICTSRCROUTE_RAW·· 269

ATK_IPOPT_STRICTSRCROUTE_RAW_SZ· 270

ATK_IPOPT_STRICTSRCROUTE_SZ· 271

ATK_IPOPT_TIMESTAMP· 272

ATK_IPOPT_TIMESTAMP_RAW·· 273

ATK_IPOPT_TIMESTAMP_RAW_SZ· 274

ATK_IPOPT_TIMESTAMP_SZ· 275

ATK_IPV6_EXT_HEADER·· 276

ATK_IPV6_EXT_HEADER_RAW·· 277

ATK_IPV6_EXT_HEADER_RAW_SZ· 277

ATK_IPV6_EXT_HEADER_SZ· 278

ATM·· 278

ATM_PVCDOWN·· 279

ATM_PVCUP· 280

BFD messages· 280

BFD_CHANGE_FSM·· 280

BFD_REACHED_UPPER_LIMIT· 281

BGP messages· 281

BGP_EXCEED_ROUTE_LIMIT· 281

BGP_REACHED_THRESHOLD·· 282

BGP_LOG_ROUTE_FLAP· 282

BGP_MEM_ALERT· 283

BGP_PEER_LICENSE_REACHED·· 283

BGP_ROUTE_LICENSE_REACHED·· 283

BGP_STATE_CHANGED·· 284

BLS messages· 284

BLS_ENTRY_ADD·· 284

BLS_ENTRY_DEL· 285

BLS_IPV6_ENTRY_ADD·· 285

BLS_IPV6_ENTRY_DEL· 286

CFD messages· 286

CFD_CROSS_CCM·· 286

CFD_ERROR_CCM·· 287

CFD_LOST_CCM·· 287

CFD_RECEIVE_CCM·· 288

CFGMAN messages· 288

CFGMAN_ARCHIVE_SCP_FAIL· 288

CFGMAN_CFGCHANGED·· 289

CFGMAN_EXIT_FROM_CONFIGURE· 290

CFGMAN_OPTCOMPLETION·· 291

CONNLMT messages· 292

CONNLMT_IPV4_OVERLOAD·· 292

CONNLMT_IPV4_RECOVER·· 293

CONNLMT_IPV6_OVERLOAD·· 294

CONNLMT_IPV6_RECOVER·· 295

DEV messages· 295

BOARD_INSERTED·· 296

BOARD_REBOOT· 296

BOARD_REMOVED·· 297

BOARD_STATE_FAULT· 298

BOARD_STATE_NORMAL· 298

BOARD_STATE_STARTING·· 299

CFCARD_INSERTED·· 299

CFCARD_REMOVED·· 300

CHASSIS_REBOOT· 300

DEV_CLOCK_CHANGE· 301

DEV_FAULT_TOOLONG·· 301

DYINGGASP· 301

FAN_ABSENT· 302

FAN_DIRECTION_NOT_PREFERRED·· 302

FAN_FAILED·· 303

FAN_RECOVERED·· 303

MAD_DETECT· 303

POWER_ABSENT· 304

POWER_CONFLICT· 304

POWER_FAILED·· 305

POWER_MONITOR_ABSENT· 305

POWER_MONITOR_FAILED·· 306

POWER_MONITOR_RECOVERED·· 306

POWER_RECOVERED·· 307

RPS_ABSENT· 307

RPS_NORMAL· 308

SUBCARD_FAULT· 309

SUBCARD_INSERTED·· 310

SUBCARD_REBOOT· 311

SUBCARD_REMOVED·· 312

SYSTEM_REBOOT· 312

TEMPERATURE_ALARM·· 313

TEMPERATURE_LOW·· 314

TEMPERATURE_NORMAL· 315

TEMPERATURE_SHUTDOWN·· 316

TEMPERATURE_WARNING·· 317

VCHK_VERSION_INCOMPATIBLE· 318

DHCP· 318

DHCP_NOTSUPPORTED·· 318

DHCP_NORESOURCES· 318

DHCPR· 319

DHCPR_SERVERCHANGE· 319

DHCPR_SWITCHMASTER·· 319

DHCPS messages· 319

DHCPS_ALLOCATE_IP· 320

DHCPS_CONFLICT_IP· 320

DHCPS_EXTEND_IP· 321

DHCPS_FILE· 321

DHCPS_RECLAIM_IP· 322

DHCPS_VERIFY_CLASS· 322

DHCPS6 messages· 322

DHCPS6_ALLOCATE_ADDRESS· 323

DHCPS6_ALLOCATE_PREFIX· 323

DHCPS6_CONFLICT_ADDRESS· 324

DHCPS6_EXTEND_ADDRESS· 324

DHCPS6_EXTEND_PREFIX· 325

DHCPS6_FILE· 325

DHCPS6_RECLAIM_ADDRESS· 326

DHCPS6_RECLAIM_PREFIX· 326

DHCPSP4· 326

DHCPSP4_FILE· 327

DHCPSP6· 327

DHCPSP6_FILE· 327

DIAG messages· 327

CPU_MINOR_RECOVERY· 327

CPU_MINOR_THRESHOLD·· 328

CPU_SEVERE_RECOVERY· 328

CPU_SEVERE_THRESHOLD·· 328

MEM_ALERT· 329

MEM_BELOW_THRESHOLD·· 330

MEM_EXCEED_THRESHOLD·· 330

DLDP messages· 330

DLDP_AUTHENTICATION_FAILED·· 331

DLDP_LINK_BIDIRECTIONAL· 331

DLDP_LINK_SHUTMODECHG·· 332

DLDP_LINK_UNIDIRECTIONAL· 332

DLDP_NEIGHBOR_AGED·· 333

DLDP_NEIGHBOR_CONFIRMED·· 333

DLDP_NEIGHBOR_DELETED·· 334

DOT1X messages· 334

DOT1X_CONFIG_NOTSUPPORT· 334

DOT1X_LOGIN_FAILURE· 335

DOT1X_LOGIN_SUCC·· 335

DOT1X_LOGIN_SUCC (in open mode) 336

DOT1X_LOGOFF· 336

DOT1X_LOGOFF (in open mode) 337

DOT1X_LOGOFF_ABNORMAL· 337

DOT1X_LOGOFF_ABNORMAL (in open mode) 338

DOT1X_MACBINDING_EXIST· 338

DOT1X_NOTENOUGH_EADFREEIP_RES· 339

DOT1X_NOTENOUGH_EADFREERULE_RES· 339

DOT1X_NOTENOUGH_EADMACREDIR_RES· 339

DOT1X_NOTENOUGH_EADPORTREDIR_RES· 340

DOT1X_NOTENOUGH_ENABLEDOT1X_RES· 340

DOT1X_SMARTON_FAILURE· 340

DOT1X_UNICAST_NOT_EFFECTIVE· 341

DRNI 341

DRNI_IFEVENT_DR_BIND·· 341

DRNI_IFEVENT_DR_GLOBALDOWN·· 341

DRNI_IFEVENT_DR_GLOBALUP· 342

DRNI_IFEVENT_DR_NOSELECTED·· 342

DRNI_IFEVENT_DR_PEER_NOSELECTED·· 342

DRNI_IFEVENT_DR_PEER_SELECTED·· 343

DRNI_IFEVENT_DR_SELECTED·· 343

DRNI_IFEVENT_DR_UNBIND·· 343

DRNI_IFEVENT_IPP_BIND·· 344

DRNI_IFEVENT_IPP_DOWN·· 344

DRNI_IFEVENT_IPP_UNBIND·· 344

DRNI_IFEVENT_IPP_UP· 345

DRNI_IPP_BLOCK· 345

DRNI_IPP_UNBLOCK· 345

DRNI_KEEPALIVEINTERVAL_MISMATCH·· 346

DRNI_KEEPALIVELINK_DOWN·· 346

DRNI_KEEPALIVELINK_UP· 346

DRNI_SECONDARY_MADDOWN·· 347

DRNI_SYSEVENT_DEVICEROLE_CHANGE· 347

DRNI_SYSEVENT_MAC_CHANGE· 347

DRNI_SYSEVENT_NUMBER_CHANGE· 348

DRNI_SYSEVENT_PRIORITY_CHANGE· 348

DRVPLAT· 348

EDEV messages· 351

EDEV_ALARM_IN_REMOVED·· 352

EDEV_ALARM_IN_REPORTEDOCCURRED·· 352

EDEV_FAILOVER_GROUP_STATE_CHANGE· 352

ERPS messages· 352

ERPS_STATE_CHANGED·· 353

ETHOAM messages· 353

ETHOAM_CONNECTION_FAIL_DOWN·· 353

ETHOAM_CONNECTION_FAIL_TIMEOUT· 353

ETHOAM_CONNECTION_FAIL_UNSATISF· 354

ETHOAM_CONNECTION_SUCCEED·· 354

ETHOAM_DISABLE· 354

ETHOAM_DISCOVERY_EXIT· 355

ETHOAM_ENABLE· 355

ETHOAM_ENTER_LOOPBACK_CTRLLED·· 355

ETHOAM_ENTER_LOOPBACK_CTRLLING·· 356

ETHOAM_LOCAL_DYING_GASP· 356

ETHOAM_LOCAL_ERROR_FRAME· 356

ETHOAM_LOCAL_ERROR_FRAME_PERIOD·· 357

ETHOAM_LOCAL_ERROR_FRAME_SECOND·· 357

ETHOAM_LOCAL_ERROR_SYMBOL· 357

ETHOAM_LOCAL_LINK_FAULT· 358

ETHOAM_LOOPBACK_EXIT· 358

ETHOAM_LOOPBACK_EXIT_ERROR_STATU·· 358

ETHOAM_LOOPBACK_NO_RESOURCE· 359

ETHOAM_LOOPBACK_NOT_SUPPORT· 359

ETHOAM_QUIT_LOOPBACK_CTRLLED·· 359

ETHOAM_QUIT_LOOPBACK_CTRLLING·· 360

ETHOAM_REMOTE_CRITICAL· 360

ETHOAM_REMOTE_DYING_GASP· 360

ETHOAM_REMOTE_ERROR_FRAME· 361

ETHOAM_REMOTE_ERROR_FRAME_PERIOD·· 361

ETHOAM_REMOTE_ERROR_FRAME_SECOND·· 361

ETHOAM_REMOTE_ERROR_SYMBOL· 362

ETHOAM_REMOTE_EXIT· 362

ETHOAM_REMOTE_FAILURE_RECOVER·· 362

ETHOAM_REMOTE_LINK_FAULT· 363

ETHOAM_NO_ENOUGH_RESOURCE· 363

ETHOAM_NOT_CONNECTION_TIMEOUT· 363

EVB messages· 363

EVB_AGG_FAILED·· 364

EVB_LICENSE_EXPIRE· 364

EVB_VSI_OFFLINE· 364

EVB_VSI_ONLINE· 365

EVIISIS messages· 365

EVIISIS_LICENSE_EXPIRED·· 365

EVIISIS_LICENSE_EXPIRED_TIME· 365

EVIISIS_LICENSE_UNAVAILABLE· 366

EVIISIS_NBR_CHG·· 366

FCLINK messages· 366

FCLINK_FDISC_REJECT_NORESOURCE· 367

FCLINK_FLOGI_REJECT_NORESOURCE· 367

FCOE messages· 367

FCOE_INTERFACE_NOTSUPPORT_FCOE· 368

FCOE_LAGG_BIND_ACTIVE· 368

FCOE_LAGG_BIND_DEACTIVE· 369

FCZONE messages· 369

FCZONE_HARDZONE_DISABLED·· 369

FCZONE_HARDZONE_ENABLED·· 369

FCZONE_ISOLATE_NEIGHBOR·· 370

FCZONE_ISOLATE_ALLNEIGHBOR·· 370

FCZONE_ISOLATE_CLEAR_VSAN·· 371

FCZONE_ISOLATE_CLEAR_ALLVSAN·· 371

FCZONE_DISTRIBUTE_FAILED·· 372

FIB messages· 372

FIB_FILE· 372

FILTER messages· 373

FILTER_EXECUTION_ICMP· 373

FILTER_EXECUTION_ICMPV6· 374

FILTER_IPV4_EXECUTION·· 375

FILTER_IPV6_EXECUTION·· 376

FIPS messages· 376

FCOE_FIPS_HARD_RESOURCE_NOENOUGH·· 376

FCOE_FIPS_HARD_RESOURCE_RESTORE· 377

FS messages· 377

FS_UNFORMATTED_PARTITION·· 377

FTPD messages· 377

FTP_ACL_DENY· 377

FTPD_REACH_SESSION_LIMIT· 378

FTPD_AUTHOR_FAILED·· 378

HA messages· 378

HA_BATCHBACKUP_FINISHED·· 379

HA_BATCHBACKUP_STARTED·· 379

HA_STANDBY_NOT_READY· 380

HA_STANDBY_TO_MASTER·· 380

HQOS messages· 380

HQOS_DP_SET_FAIL· 381

HQOS_FP_SET_FAIL· 381

HQOS_POLICY_APPLY_FAIL· 382

HQOS_POLICY_APPLY_FAIL· 382

HTTPD messages· 382

HTTPD_CONNECT· 383

HTTPD_CONNECT_TIMEOUT· 383

HTTPD_DISCONNECT· 383

HTTPD_FAIL_FOR_ACL· 384

HTTPD_FAIL_FOR_ACP· 384

HTTPD_REACH_CONNECT_LIMIT· 384

IFNET messages· 385

IF_BUFFER_CONGESTION_OCCURRENCE· 385

IF_BUFFER_CONGESTION_CLEAR·· 385

INTERFACE_NOTSUPPRESSED·· 386

INTERFACE_SUPPRESSED·· 386

LINK_UPDOWN·· 386

PHY_UPDOWN·· 387

PROTOCOL_UPDOWN·· 387

TUNNEL_LINK_UPDOWN·· 387

TUNNEL_PHY_UPDOWN·· 388

VLAN_MODE_CHANGE· 388

IKE messages· 388

IKE_P1_SA_ESTABLISH_FAIL· 389

IKE_P2_SA_ESTABLISH_FAIL· 390

IKE_P2_SA_TERMINATE· 390

IPSEC messages· 390

IPSEC_FAILED_ADD_FLOW_TABLE· 391

IPSEC_PACKET_DISCARDED·· 391

IPSEC_SA_ESTABLISH·· 392

IPSEC_SA_ESTABLISH_FAIL· 392

IPSEC_SA_INITINATION·· 393

IPSEC_SA_TERMINATE· 393

IPSG messages· 393

IPSG_ADDENTRY_ERROR·· 394

IPSG_DELENTRY_ERROR·· 395

IPSG_ADDEXCLUDEDVLAN_ERROR·· 396

IPSG_DELEXCLUDEDVLAN_ERROR·· 397

IRDP messages· 397

IRDP_EXCEED_ADVADDR_LIMIT· 397

IRF· 397

IRF_LINK_BLOCK· 398

IRF_LINK_DOWN·· 398

IRF_LINK_UP· 398

IRF_MEMBERID_CONFLICT· 399

IRF_MERGE· 399

IRF_MERGE_NEED_REBOOT· 399

IRF_MERGE_NOT_NEED_REBOOT· 400

ISIS messages· 400

ISIS_LSP_CONFLICT· 400

ISIS_MEM_ALERT· 400

ISIS_NBR_CHG·· 401

ISSU messages· 401

ISSU_ROLLBACKCHECKNORMAL· 401

ISSU_PROCESSWITCHOVER·· 402

L2PT messages· 402

L2PT_SET_MULTIMAC_FAILED·· 402

L2PT_CREATE_TUNNELGROUP_FAILED·· 402

L2PT_ADD_GROUPMEMBER_FAILED·· 403

L2PT_ENABLE_DROP_FAILED·· 403

L2TP messages· 403

L2TPV2_TUNNEL_EXCEED_LIMIT· 403

L2TPV2_SESSION_EXCEED_LIMIT· 404

L2VPN messages· 404

L2VPN_BGPVC_CONFLICT_LOCAL· 404

L2VPN_BGPVC_CONFLICT_REMOTE· 405

L2VPN_HARD_RESOURCE_NOENOUGH·· 405

L2VPN_HARD_RESOURCE_RESTORE· 405

L2VPN_LABEL_DUPLICATE· 406

LAGG messages· 406

LAGG_ACTIVE· 406

LAGG_INACTIVE_AICFG·· 407

LAGG_INACTIVE_BFD·· 407

LAGG_INACTIVE_CONFIGURATION·· 408

LAGG_INACTIVE_DUPLEX· 408

LAGG_INACTIVE_HARDWAREVALUE· 409

LAGG_INACTIVE_LOWER_LIMIT· 409

LAGG_INACTIVE_PARTNER·· 409

LAGG_INACTIVE_PHYSTATE· 410

LAGG_INACTIVE_RESOURCE_INSUFICIE· 410

LAGG_INACTIVE_SPEED·· 410

LAGG_INACTIVE_UPPER_LIMIT· 411

LDP messages· 411

LDP_MPLSLSRID_CHG·· 411

LDP_SESSION_CHG·· 412

LDP_SESSION_GR·· 413

LDP_SESSION_SP· 413

LLDP messages· 413

LLDP_CREATE_NEIGHBOR·· 414

LLDP_DELETE_NEIGHBOR·· 414

LLDP_LESS_THAN_NEIGHBOR_LIMIT· 415

LLDP_NEIGHBOR_AGE_OUT· 415

LLDP_NEIGHBOR_PROTECTION_BLOCK· 416

LLDP_NEIGHBOR_PROTECTION_DOWN·· 416

LLDP_NEIGHBOR_PROTECTION_UNBLOCK· 417

LLDP_NEIGHBOR_PROTECTION_UP· 417

LLDP_PVID_INCONSISTENT· 417

LLDP_REACH_NEIGHBOR_LIMIT· 418

LOAD messages· 418

BOARD_LOADING·· 418

LOAD_FAILED·· 419

LOAD_FINISHED·· 419

LOGIN messages· 419

LOGIN_FAILED·· 420

LOGIN_ INVALID_USERNAME_PWD·· 420

LPDT messages· 420

LPDT_LOOPED·· 420

LPDT_RECOVERED·· 421

LPDT_VLAN_LOOPED·· 421

LPDT_VLAN_RECOVERED·· 421

LS messages· 421

LS_ADD_USER_TO_GROUP· 422

LS_AUTHEN_FAILURE· 422

LS_AUTHEN_SUCCESS· 422

LS_DEL_USER_FROM_GROUP· 423

LS_DELETE_PASSWORD_FAIL· 423

LS_PWD_ADDBLACKLIST· 423

LS_PWD_CHGPWD_FOR_AGEDOUT· 424

LS_PWD_CHGPWD_FOR_AGEOUT· 424

LS_PWD_CHGPWD_FOR_COMPOSITION·· 424

LS_PWD_CHGPWD_FOR_FIRSTLOGIN·· 425

LS_PWD_CHGPWD_FOR_LENGTH·· 425

LS_PWD_FAILED2WRITEPASS2FILE· 425

LS_PWD_MODIFY_FAIL· 426

LS_PWD_MODIFY_SUCCESS· 426

LS_REAUTHEN_FAILURE· 426

LS_UPDATE_PASSWORD_FAIL· 427

LS_USER_CANCEL· 427

LS_USER_PASSWORD_EXPIRE· 427

LS_USER_ROLE_CHANGE· 428

LSPV messages· 428

LSPV_PING_STATIS_INFO·· 428

MAC messages· 428

MAC_DRIVER_ADD_ENTRY· 429

MAC_TABLE_FULL_GLOBAL· 429

MAC_TABLE_FULL_PORT· 429

MAC_TABLE_FULL_VLAN·· 430

MAC_VLAN_LEARNLIMIT_NORESOURCE· 430

MAC_VLAN_LEARNLIMIT_NOTSUPPORT· 430

MACA messages· 430

MACA_ENABLE_NOT_EFFECTIVE· 431

MACA_LOGIN_FAILURE· 431

MACA_LOGIN_SUCC·· 432

MACA_LOGIN_SUCC (in open mode) 432

MACA_LOGOFF· 433

MACA_LOGOFF (in open mode) 433

MACSEC messages· 433

MACSEC_MKA_KEEPALIVE_TIMEOUT· 434

MACSEC_MKA_PRINCIPAL_ACTOR·· 434

MACSEC_MKA_SAK_REFRESH·· 434

MACSEC_MKA_SESSION_REAUTH·· 435

MACSEC_MKA_SESSION_SECURED·· 435

MACSEC_MKA_SESSION_START· 436

MACSEC_MKA_SESSION_STOP· 436

MACSEC_MKA_SESSION_UNSECURED·· 437

MBFD messages· 437

MBFD_TRACEROUTE_FAILURE· 437

MBUF messages· 437

MBUF_DATA_BLOCK_CREATE_FAIL· 438

MDC messages· 438

MDC_CREATE_ERR·· 439

MDC_CREATE· 439

MDC_DELETE· 439

MDC_KERNEL_EVENT_TOOLONG·· 440

MDC_LICENSE_EXPIRE· 440

MDC_NO_FORMAL_LICENSE· 440

MDC_NO_LICENSE_EXIT· 441

MDC_OFFLINE· 441

MDC_ONLINE· 441

MDC_STATE_CHANGE· 442

MFIB messages· 442

MFIB_MEM_ALERT· 442

MGROUP messages· 442

MGROUP_APPLY_SAMPLER_FAIL· 443

MGROUP_RESTORE_CPUCFG_FAIL· 443

MGROUP_RESTORE_IFCFG_FAIL· 444

MGROUP_SYNC_CFG_FAIL· 444

MPLS messages· 444

MPLS_HARD_RESOURCE_NOENOUGH·· 445

MPLS_HARD_RESOURCE_RESTORE· 445

MTLK messages· 445

MTLK_UPLINK_STATUS_CHANGE· 445

NAT messages· 445

NAT_ADDR_BIND_CONFLICT· 446

NAT_FAILED_ADD_FLOW_RULE· 446

NAT_FAILED_ADD_FLOW_TABLE· 447

NAT_FLOW·· 448

NAT_SERVER_INVALID·· 449

NAT_SERVICE_CARD_RECOVER_FAILURE· 450

ND messages· 450

ND_CONFLICT· 451

ND_DUPADDR·· 451

ND_HOST_IP_CONFLICT· 452

ND_MAC_CHECK· 452

ND_RAGUARD_DROP· 453

ND_SET_PORT_TRUST_NORESOURCE· 453

ND_SET_VLAN_REDIRECT_NORESOURCE· 453

ETCONF messages· 453

CLI 454

row-operation· 455

THREAD·· 455

NQA messages· 456

NQA_LOG_UNREACHABLE· 456

NTP messages· 456

NTP_CLOCK_CHANGE· 456

NTP_LEAP_CHANGE· 457

NTP_SOURCE_CHANGE· 457

NTP_SOURCE_LOST· 458

NTP_STRATUM_CHANGE· 458

OBJP messages· 458

OBJP_ACCELERATE_NO_RES· 459

OBJP_ACCELERATE_NOT_SUPPORT· 459

OBJP_ACCELERATE_UNK_ERR·· 459

OFP messages· 459

OFP_ACTIVE· 460

OFP_ACTIVE_FAILED·· 460

OFP_CONNECT· 460

OFP_FAIL_OPEN·· 461

OFP_FLOW_ADD·· 461

OFP_FLOW_ADD_DUP· 462

OFP_FLOW_ADD_FAILED·· 462

OFP_FLOW_ADD_FAILED·· 463

OFP_FLOW_ADD_TABLE_MISS· 463

OFP_FLOW_ADD_TABLE_MISS_FAILED·· 464

OFP_FLOW_DEL· 464

OFP_FLOW_DEL_TABLE_MISS· 465

OFP_FLOW_DEL_TABLE_MISS_FAILED·· 465

OFP_FLOW_MOD·· 466

OFP_FLOW_MOD_FAILED·· 466

OFP_FLOW_MOD_TABLE_MISS· 467

OFP_FLOW_MOD_TABLE_MISS_FAILED·· 467

OFP_FLOW_RMV_GROUP· 467

OFP_FLOW_RMV_HARDTIME· 468

OFP_FLOW_RMV_IDLETIME· 468

OFP_FLOW_RMV_METER·· 468

OFP_FLOW_UPDATE_FAILED·· 469

OFP_GROUP_ADD·· 469

OFP_GROUP_ADD_FAILED·· 470

OFP_GROUP_DEL· 470

OFP_GROUP_MOD·· 470

OFP_GROUP_MOD_FAILED·· 471

OFP_METER_ADD·· 471

OFP_METER_ADD_FAILED·· 471

OFP_METER_DEL· 472

OFP_METER_MOD·· 472

OFP_METER_MOD_FAILED·· 473

OFP_MISS_RMV_GROUP· 473

OFP_MISS_RMV_HARDTIME· 473

OFP_MISS_RMV_IDLETIME· 474

OFP_MISS_RMV_METER·· 474

OFP_RADARDETECTION·· 474

PORT_MOD·· 475

OPENSRC (FreeRADIUS) messages· 476

HUP event 476

Process restart event 477

Process start event 477

User authentication· 478

OPTMOD messages· 480

BIAS_HIGH·· 481

BIAS_LOW·· 481

BIAS_NORMAL· 481

CFG_ERR·· 482

CHKSUM_ERR·· 482

FIBER_SFP MODULE_INVALID·· 482

FIBER_SFPMODULE_NOWINVALID·· 483

IO_ERR·· 483

MOD_ALM_OFF· 483

MOD_ALM_ON·· 484

MODULE_IN·· 484

MODULE_OUT· 484

PHONY_MODULE· 485

RX_ALM_OFF· 485

RX_ALM_ON·· 485

RX_POW_HIGH·· 486

RX_POW_LOW·· 486

RX_POW_NORMAL· 486

TEMP_HIGH·· 487

TEMP_LOW·· 487

TEMP_NORMAL· 487

TX_ALM_OFF· 488

TX_ALM_ON·· 488

TX_POW_HIGH·· 488

TX_POW_LOW·· 489

TX_POW_NORMAL· 489

TYPE_ERR·· 489

VOLT_HIGH·· 490

VOLT_LOW·· 490

VOLT_NORMAL· 490

OSPF messages· 490

OSPF_DUP_RTRID_NBR·· 491

OSPF_IP_CONFLICT_INTRA· 491

OSPF_LAST_NBR_DOWN·· 492

OSPF_MEM_ALERT· 492

OSPF_NBR_CHG·· 493

OSPF_RT_LMT· 493

OSPF_RTRID_CHG·· 493

OSPF_RTRID_CONFLICT_INTER·· 494

OSPF_RTRID_CONFLICT_INTRA· 494

OSPF_VLINKID_CHG·· 494

OSPFV3 messages· 495

OSPFV3_LAST_NBR_DOWN·· 495

OSPFV3_MEM_ALERT· 495

OSPFV3_NBR_CHG·· 496

OSPFV3_RT_LMT· 496

Packet capture messages· 496

PKTCPT_AP_OFFLINE· 497

PKTCPT_AREADY_EXIT· 497

PKTCPT_CONN_FAIL· 498

PKTCPT_INVALID_FILTER·· 498

PKTCPT_LOGIN_DENIED·· 498

PKTCPT_MEMORY_ALERT· 499

PKTCPT_OPEN_FAIL· 499

PKTCPT_OPERATION_TIMEOUT· 499

PKTCPT_SERVICE_FAIL· 500

PKTCPT_UNKNOWN_ERROR·· 500

PKTCPT_UPLOAD_ERROR·· 500

PKTCPT_WRITE_FAIL· 501

PBB messages· 501

PBB_JOINAGG_WARNING·· 501

PBR messages· 501

PBR_HARDWARE_ERROR·· 502

PCE messages· 502

PCE_PCEP_SESSION_CHG·· 503

PEX messages (IRF 3) 503

PEX_ASSOCIATEID_MISMATCHING·· 504

PEX_CONFIG_ERROR·· 504

PEX_CONNECTION_ERROR·· 505

PEX_FORBID_STACK· 505

PEX_LINK_BLOCK· 506

PEX_LINK_DOWN·· 507

PEX_LINK_FORWARD·· 507

PEX_REG_JOININ·· 508

PEX_REG_LEAVE· 508

PEX_REG_REQUEST· 509

PEX_STACKCONNECTION_ERROR·· 509

PEX messages (IRF 3.1) 509

PEX_AUTOCONFIG_BAGG_ASSIGNMEMBER·· 510

PEX_AUTOCONFIG_BAGG_CREATE· 510

PEX_AUTOCONFIG_BAGG_NORESOURCE· 510

PEX_AUTOCONFIG_BAGG_REMOVEMEMBER·· 511

PEX_AUTOCONFIG_CAPABILITY_ENABLE· 511

PEX_AUTOCONFIG_CASCADELIMIT· 512

PEX_AUTOCONFIG_CONNECTION_ERROR·· 512

PEX_AUTOCONFIG_DIFFGROUPNUMBER·· 512

PEX_AUTOCONFIG_DYNAMICBAGG_STP· 513

PEX_AUTOCONFIG_GROUP_CREATE· 513

PEX_AUTOCONFIG_NONUMBERRESOURCE· 513

PEX_AUTOCONFIG_NOT_CASCADEPORT· 514

PEX_AUTOCONFIG_NUMBER_ASSIGN·· 514

PEX_LLDP_DISCOVER·· 515

PEX_MEMBERID_EXCEED·· 515

PEX_PECSP_OPEN_RCVD·· 515

PEX_PECSP_OPEN_SEND·· 516

PEX_PECSP_TIMEOUT· 516

PFILTER messages· 516

PFILTER_GLB_IPV4_DACT_NO_RES· 517

PFILTER_GLB_IPV4_DACT_UNK_ERR·· 517

PFILTER_GLB_IPV6_DACT_NO_RES· 518

PFILTER_GLB_IPV6_DACT_UNK_ERR·· 518

PFILTER_GLB_MAC_DACT_NO_RES· 519

PFILTER_GLB_MAC_DACT_UNK_ERR·· 519

PFILTER_GLB_NO_RES· 520

PFILTER_GLB_NOT_SUPPORT· 520

PFILTER_GLB_ RES_CONFLICT· 521

PFILTER_GLB_UNK_ERR·· 521

PFILTER_IF_IPV4_DACT_NO_RES· 522

PFILTER_IF_IPV4_DACT_UNK_ERR·· 522

PFILTER_IF_IPV6_DACT_NO_RES· 523

PFILTER_IF_IPV6_DACT_UNK_ERR·· 523

PFILTER_IF_MAC_DACT_NO_RES· 524

PFILTER_IF_MAC_DACT_UNK_ERR·· 524

PFILTER_IF_NO_RES· 525

PFILTER_IF_NOT_SUPPORT· 525

PFILTER_IF_RES_CONFLICT· 526

PFILTER_IF_UNK_ERR·· 526

PFILTER_IPV6_STATIS_INFO·· 527

PFILTER_STATIS_INFO·· 527

PFILTER_VLAN_IPV4_DACT_NO_RES· 528

PFILTER_VLAN_IPV4_DACT_UNK_ERR·· 528

PFILTER_VLAN_IPV6_DACT_NO_RES· 529

PFILTER_VLAN_IPV6_DACT_UNK_ERR·· 529

PFILTER_VLAN_MAC_DACT_NO_RES· 530

PFILTER_VLAN_MAC_DACT_UNK_ERR·· 530

PFILTER_VLAN_NO_RES· 531

PFILTER_VLAN_NOT_SUPPORT· 531

PFILTER_VLAN_RES_CONFLICT· 532

PFILTER_VLAN_UNK_ERR·· 532

PIM messages· 532

PIM_NBR_DOWN·· 533

PIM_NBR_UP· 533

PING messages· 533

PING_STATISTICS· 534

PING_VPN_STATISTICS· 535

PKI messages· 535

REQUEST_CERT_FAIL· 535

REQUEST_CERT_SUCCESS· 536

PKT2CPU messages· 536

PKT2CPU_NO_RESOURCE· 536

Portal messages· 536

PORTAL_RULE_FAILED·· 537

PORTSEC messages· 537

PORTSEC_ACL_FAILURE· 538

PORTSEC_CAR_FAILURE· 538

PORTSEC_CREATEAC_FAILURE· 539

PORTSEC_LEARNED_MACADDR·· 539

PORTSEC_NTK_NOT_EFFECTIVE· 540

PORTSEC_PORTMODE_NOT_EFFECTIVE· 540

PORTSEC_PROFILE_FAILURE· 540

PORTSEC_URL_FAILURE· 541

PORTSEC_VIOLATION·· 541

PPP messages· 541

IPPOOL_ADDRESS_EXHAUSTED·· 542

PPP_USER_LOGON_SUCCESS· 542

PPP_USER_LOGON_FAILED·· 543

PPP_USER_LOGOFF· 543

PWDCTL messages· 544

ADDBLACKLIST· 544

CHANGEPASSWORD·· 545

FAILEDTOWRITEPWD·· 545

QOS messages· 545

MIRROR_SYNC_CFG_FAIL· 546

QOS_CAR_APPLYUSER_FAIL· 546

QOS_CBWFQ_REMOVED·· 547

QOS_GTS_APPLYUSER_FAIL· 547

QOS_NOT_ENOUGH_BANDWIDTH·· 548

QOS_POLICY_APPLYCOPP_CBFAIL· 548

QOS_POLICY_APPLYCOPP_FAIL· 549

QOS_POLICY_APPLYGLOBAL_CBFAIL· 549

QOS_POLICY_APPLYGLOBAL_FAIL· 550

QOS_POLICY_APPLYIF_CBFAIL· 550

QOS_POLICY_APPLYIF_FAIL· 551

QOS_POLICY_APPLYUSER_FAIL· 551

QOS_POLICY_APPLYVLAN_CBFAIL· 552

QOS_POLICY_APPLYVLAN_FAIL· 552

QOS_QMPROFILE_APPLYUSER_FAIL· 553

QOS_QMPROFILE_MODIFYQUEUE_FAIL· 553

WRED_TABLE_CFG_FAIL· 554

RADIUS messages· 554

RADIUS_AUTH_FAILURE· 554

RADIUS_AUTH_SUCCESS· 554

RADIUS_DELETE_HOST_FAIL· 555

RDDC messages· 555

RDDC_ACTIVENODE_CHANGE· 555

RESMON· 555

RESMON_MINOR·· 556

RESMON_MINOR_RECOVERY· 556

RESMON_SEVERE· 557

RESMON_SEVERE_RECOVERY· 557

RESMON_USEDUP· 558

RESMON_USEDUP_RECOVERY· 558

RIP messages· 558

RIP_MEM_ALERT· 559

RIP_RT_LMT· 559

RIPNG messages· 559

RIPNG_MEM_ALERT· 559

RIPNG_RT_LMT· 560

RM messages· 560

RM_ACRT_REACH_LIMIT· 560

RM_ACRT_REACH_THRESVALUE· 560

RM_THRESHLD_VALUE_REACH·· 561

RM_TOTAL_THRESHLD_VALUE_REACH·· 561

RPR messages· 561

RPR_EXCEED_MAX_SEC_MAC·· 561

RPR_EXCEED_MAX_SEC_MAC_OVER·· 562

RPR_EXCEED_MAX_STATION·· 562

RPR_EXCEED_MAX_STATION_OVER·· 562

RPR_EXCEED_RESERVED_RATE· 563

RPR_EXCEED_RESERVED_RATE_OVER·· 563

RPR_IP_DUPLICATE· 563

RPR_IP_DUPLICATE_OVER·· 564

RPR_JUMBO_INCONSISTENT· 564

RPR_JUMBO_INCONSISTENT_OVER·· 564

RPR_MISCABLING·· 565

RPR_MISCABLING_OVER·· 565

RPR_PROTECTION_INCONSISTENT· 565

RPR_PROTECTION_INCONSISTENT_OVER·· 566

RPR_SEC_MAC_DUPLICATE· 566

RPR_SEC_MAC_DUPLICATE_OVER·· 566

RPR_TOPOLOGY_INCONSISTENT· 567

RPR_TOPOLOGY_INCONSISTENT_OVER·· 567

RPR_TOPOLOGY_INSTABILITY· 567

RPR_TOPOLOGY_INSTABILITY_OVER·· 568

RPR_TOPOLOGY_INVALID·· 568

RPR_TOPOLOGY_INVALID_OVER·· 568

RRPP messages· 568

RRPP_RING_FAIL· 569

RRPP_RING_RESTORE· 569

RTM messages· 569

RTM_TCL_NOT_EXIST· 569

RTM_TCL_MODIFY· 570

RTM_TCL_LOAD_FAILED·· 570

SCM messages· 570

PROCESS_ABNORMAL· 571

PROCESS_ACTIVEFAILED·· 571

SCM_ABNORMAL_REBOOT· 572

SCM_ABNORMAL_REBOOTMDC·· 573

SCM_ABORT_RESTORE· 573

SCM_INSMOD_ADDON_TOOLONG·· 574

SCM_KERNEL_INIT_TOOLONG·· 574

SCM_PROCESS_STARTING_TOOLONG·· 575

SCM_PROCESS_STILL_STARTING·· 575

SCM_SKIP_PROCESS· 576

SCM_SKIP_PROCESS· 576

SCRLSP messages· 576

SCRLSP_LABEL_DUPLICATE· 577

SESSION messages· 577

SESSION_IPV4_FLOW·· 578

SESSION_IPV6_FLOW·· 579

SFLOW messages· 580

SFLOW_HARDWARE_ERROR·· 580

SHELL messages· 580

SHELL_CMD·· 580

SHELL_CMD_CONFIRM·· 581

SHELL_CMD_EXECUTEFAIL· 581

SHELL_CMD_INPUT· 581

SHELL_CMD_INPUT_TIMEOUT· 582

SHELL_CMD_MATCHFAIL· 582

SHELL_CMDDENY· 582

SHELL_CMDFAIL· 583

SHELL_CRITICAL_CMDFAIL· 583

SHELL_LOGIN·· 583

SHELL_LOGOUT· 584

SLSP messages· 584

SLSP_LABEL_DUPLICATE· 584

SMLK messages· 584

SMLK_LINK_SWITCH·· 585

SNMP messages· 585

SNMP_ACL_RESTRICTION·· 585

SNMP_AUTHENTICATION_FAILURE· 585

SNMP_GET· 586

SNMP_NOTIFY· 586

SNMP_SET· 587

SNMP_USM_NOTINTIMEWINDOW·· 587

SSHS messages· 587

SSHS_ACL_DENY· 588

SSHS_ALGORITHM_MISMATCH·· 588

SSHS_AUTH_EXCEED_RETRY_TIMES· 588

SSHS_AUTH_FAIL· 589

SSHS_AUTH_TIMEOUT· 589

SSHS_CONNECT· 589

SSHS_DECRYPT_FAIL· 590

SSHS_DISCONNECT· 590

SSHS_ENCRYPT_FAIL· 590

SSHS_LOG·· 591

SSHS_MAC_ERROR·· 591

SSHS_REACH_SESSION_LIMIT· 591

SSHS_REACH_USER_LIMIT· 592

SSHS_SCP_OPER·· 592

SSHS_SFTP_OPER·· 593

SSHS_SRV_UNAVAILABLE· 593

SSHS_VERSION_MISMATCH·· 593

STAMGR messages· 594

STAMGR_ADD_FAILVLAN·· 594

STAMGR_ADDBAC_INFO·· 594

STAMGR_ADDSTA_INFO·· 594

STAMGR_AUTHORACL_FAILURE· 595

STAMGR_AUTHORUSERPROFILE_FAILURE· 595

STAMGR_CLIENT_OFFLINE· 596

STAMGR_CLIENT_ONLINE· 596

STAMGR_DELBAC_INFO·· 596

STAMGR_DELSTA_INFO·· 597

STAMGR_DOT1X_LOGIN_FAILURE· 597

STAMGR_DOT1X_LOGIN_SUCC·· 598

STAMGR_DOT1X_LOGOFF· 598

STAMGR_MACA_LOGIN_FAILURE· 599

STAMGR_MACA_LOGIN_SUCC·· 599

STAMGR_MACA_LOGOFF· 600

STAMGR_STAIPCHANGE_INFO·· 600

STAMGR_TRIGGER_IP· 601

STM messages· 601

STM_AUTO_UPDATE_FAILED·· 602

STM_AUTO_UPDATE_FAILED·· 603

STM_AUTO_UPDATE_FINISHED·· 603

STM_AUTO_UPDATE_FINISHED·· 604

STM_AUTO_UPDATING·· 604

STM_AUTO_UPDATING·· 604

STM_LINK_DOWN·· 605

STM_LINK_MERGE· 605

STM_LINK_TIMEOUT· 605

STM_LINK_UP· 605

STM_MERGE_NEED_REBOOT· 606

STM_MERGE_NOT_NEED_REBOOT· 606

STM_SAMEMAC·· 606

STM_SOMER_CHECK· 607

STP messages· 607

STP_BPDU_PROTECTION·· 607

STP_BPDU_RECEIVE_EXPIRY· 607

STP_CONSISTENCY_RESTORATION·· 608

STP_DETECTED_TC·· 608

STP_DISABLE· 608

STP_DISCARDING·· 609

STP_DISPUTE· 609

STP_ENABLE· 609

STP_FORWARDING·· 610

STP_LOOP_PROTECTION·· 610

STP_LOOPBACK_PROTECTION·· 610

STP_NOT_ROOT· 611

STP_NOTIFIED_TC·· 611

STP_PORT_TYPE_INCONSISTENCY· 611

STP_PVID_INCONSISTENCY· 612

STP_PVST_BPDU_PROTECTION·· 612

STP_ROOT_PROTECTION·· 612

SYSEVENT· 612

EVENT_TIMEOUT· 613

SYSLOG messages· 613

SYSLOG_LOGFILE_FULL· 613

SYSLOG_NO_SPACE· 614

SYSLOG_RESTART· 614

SYSLOG_RTM_EVENT_BUFFER_FULL· 614

TACACS messages· 615

TACACS_AUTH_FAILURE· 615

TACACS_AUTH_SUCCESS· 615

TACACS_DELETE_HOST_FAIL· 615

TELNETD messages· 615

TELNETD_ACL_DENY· 616

TELNETD_REACH_SESSION_LIMIT· 616

TRILL messages· 616

TRILL_DUP_SYSTEMID·· 617

TRILL_INTF_CAPABILITY· 617

TRILL_LICENSE_EXPIRED·· 617

TRILL_LICENSE_EXPIRED_TIME· 618

TRILL_LICENSE_UNAVAILABLE· 618

TRILL_MEM_ALERT· 618

TRILL_NBR_CHG·· 619

VCF messages· 619

VCF_AGGR_CREAT· 619

VCF_AGGR_DELETE· 620

VCF_AGGR_FAILED·· 620

VCF_AUTO_ANALYZE_USERDEF· 620

VCF_AUTO_NO_USERDEF· 621

VCF_AUTO_START· 621

VCF_AUTO_STATIC_CMD·· 621

VCF_BGP· 622

VCF_DOWN_LINK· 622

VCF_GET_IMAGE· 623

VCF_GET_TEMPLATE· 623

VCF_INSTALL_IMAGE· 623

VCF_IRF_FINISH·· 624

VCF_IRF_FOUND·· 624

VCF_IRF_REBOOT· 625

VCF_IRF_START· 625

VCF_LOOPBACK_START· 626

VCF_LOOPBACK_START_FAILED·· 626

VCF_LOOPBACK_ALLOC·· 627

VCF_LOOPBACK_NO_FREE_IP· 627

VCF_LOOPBACK_RECLAIM·· 628

VCF_REBOOT· 628

VCF_SKIP_INSTALL· 628

VCF_STATIC_CMD_ERROR·· 629

VCF_UP_LINK· 629

VLAN messages· 629

VLAN_FAILED·· 630

VLAN_VLANMAPPING_FAILED·· 630

VLAN_VLANTRANSPARENT_FAILED·· 630

VRRP messages· 631

VRRP_STATUS_CHANGE· 631

VRRP_VF_STATUS_CHANGE· 632

VRRP_VMAC_INEFFECTIVE· 632

VSRP messages· 632

VSRP_BIND_FAILED·· 633

VXLAN messages· 633

VXLAN_LICENSE_UNAVAILABLE· 633

WIPS messages· 633

WIPS_APFLOOD·· 633

WIPS_AP_CHANNEL_CHANGE· 634

WIPS_ASSOCIATEOVERFLOW·· 634

WIPS_DOS· 634

WIPS_FLOOD·· 635

WIPS_HONEYPOT· 635

WIPS_HTGREENMODE· 636

WIPS_MALF· 636

WIPS_MAN_IN_MIDDLE· 637

WIPS_SPOOF· 637

WIPS_WEAKIV· 637

WIPS_WIRELESSBRIDGE· 638

 


Introduction

This document includes the following system messages:

·     Messages specific to Release 2612 of the switch.

·     Messages for the Comware 7 software platform version based on which Release 2612 was produced. Some platform system messages might not be available on the switch.

This document is intended only for managing S6860 switches. Do not use this document for any other device models.

This document assumes that the readers are familiar with data communications technologies and H3C networking products.

System log message format

By default, the system log messages use one of the following formats depending on the output destination:

·     Log host:

<PRI>TIMESTAMP Sysname %%vendorMODULE/severity/MNEMONIC: location; CONTENT

·     Destinations except for the log host:

Prefix TIMESTAMP Sysname MODULE/severity/MNEMONIC: CONTENT

Table 1 System log message elements

Element

Description

<PRI>

Priority identifier. It is calculated by using the following formula:

Priority identifier=facilityx8+severity

Where:

·     Facility is specified by using the info-center loghost command. A log host uses this parameter to identify log sources and filter log messages.

·     Severity represents the importance of the message. For more information about severity levels, see Table 2.

Prefix

Message type identifier. This element is contained in the system log messages sent to non-log host destinations.

The element uses the following symbols to indicate message severity:

·     Percentage sign (%)—Informational and higher levels.

·     Asterisk (*)—Debug level.

TIMESTAMP

Date and time when the event occurred.

The following are commands for configuring the timestamp format:

·     Log host—Use the info-center timestamp loghost command.

·     Non-log host destinations—Use the info-center timestamp command.

Sysname

Name or IP address of the device that generated the message.

%%vendor

Manufacturer flag. This element is %%10 for H3C.

This element is only available in messages sent to the log host.

MODULE

Name of the module that produced the message.

severity

Severity level of the message. (For more information about severity levels, see Table 2.)

MNEMONIC

Text string that uniquely identifies the system message. The maximum length is 32 characters.

location

Optional. This element presents location information for the message in the following format:

-attribute1=x-attribute2=y…-attributeN=z

This element is separated from the message description by using a semicolon (;).

CONTENT

Text string that contains detailed information about the event or error.

For variable fields in this element, this document uses the representations in Table 3.

 

System log messages are classified into eight severity levels from 0 to 7. The lower the number, the higher the severity, as shown in Table 2.

Table 2 System log message severity levels

Level

Severity

Description

0

Emergency

The system is unusable. For example, the system authorization has expired.

1

Alert

Action must be taken immediately. For example, traffic on an interface exceeds the upper limit.

2

Critical

Critical condition. For example, the device temperature exceeds the upper limit, the power module fails, or the fan tray fails.

3

Error

Error condition. For example, the link state changes or a storage card is unplugged.

4

Warning

Warning condition. For example, an interface is disconnected, or the memory resources are used up.

5

Notification

Normal but significant condition. For example, a terminal logs in to the device, or the device reboots.

6

Informational

Informational message. For example, a command or a ping operation is executed.

7

Debug

Debugging message.

 

For variable fields in the message text, this document uses the representations in Table 3. The values are case insensitive, even though the representations are uppercase letters.

Table 3 Variable field representations

Representation

Information type

INT16

Signed 16-bit decimal number.

UINT16

Unsigned 16-bit decimal number.

INT32

Signed 32-bit decimal number.

UINT32

Unsigned 32-bit decimal number.

INT64

Signed 64-bit decimal number.

UINT64

Unsigned 64-bit decimal number.

DOUBLE

Two dot-separated signed 32-bit decimal numbers. The format is [INTEGER].[INTEGER].

HEX

Hexadecimal number.

CHAR

Single character.

STRING

Character string.

IPADDR

IP address.

MAC

MAC address.

DATE

Date.

TIME

Time.

 

Managing and obtaining system log messages

You can manage system log messages by using the information center.

By default, the information center is enabled. Log messages can be output to the console, log buffer, monitor terminal, log host, and log file.

To filter log messages, use the info-center source command to specify log output rules. A log output rule specifies the source modules and the lowest severity level of log messages that can be output to a destination. A log message is output if its severity level is higher than or equal to the specified level. For example, if you specify a severity level of 6 (informational), log messages that have a severity level from 0 to 6 are output.

For more information about using the information center, see the network management and monitoring configuration guide for the product.

Obtaining log messages from the console terminal

Access the device through the console port. Real-time log messages are displayed on the console terminal.

Obtaining log messages from the log buffer

Use the display logbuffer command to display history log messages in the log buffer.

Obtaining log messages from a monitor terminal

Monitor terminals refer to terminals that access the device through the AUX, VTY, or TTY lines (for example, Telnet). To obtain log messages from a monitor terminal, use the following guidelines:

·     To display log messages on the monitor terminal, you must configure the terminal monitor command.

·     For monitor terminals, the lowest level of log messages that can be displayed is determined by both the terminal logging level and info-center source commands.

Obtaining log messages from the log file

By default, the log file feature automatically saves logs from the log file buffer to the log file every 24 hours. You can use the info-center logfile frequency command to change the automatic saving internal.

To manually save logs to the log file, use the logfile save command. The log file buffer is cleared each time a save operation is performed.

By default, you can obtain the log file from the cfa0:/logfile/ path if the CF card is not partitioned. If the CF card is partitioned, the file path is cfa1:/logfile/.

Obtaining log messages from a log host

Use the info-center loghost command to specify the service port number and IP address of a log host. To specify multiple log hosts, repeat the command.

For a successful log message transmission, make sure the specified port number is the same as the port number used on the log host. The default service port number is 514.

Software module list

Table 4 lists all software modules that might produce system log messages. This document uses "OPENSRC" to represent all open source modules.

Table 4 Software module list

Module name representation

Module name expansion

AAA

Authentication, Authorization and Accounting

ACL

Access Control List

ANCP

Access Node Control Protocol

APMGR

Access Point Management

ARP

Address Resolution Protocol

ATK

Attack Detection and Prevention

ATM

Asynchronous Transfer Mode

BFD

Bidirectional Forwarding Detection

BGP

Border Gateway Protocol

BLS

Blacklist

CFD

Connectivity Fault Detection

CFGMAN

Configuration Management

CONNLMT

Connection Limit

DEV

Device Management

DHCP

Dynamic Host Configuration Protocol

DHCPR

IPv4 DHCP Relay

DHCPS

DHCP Server

DHCPS6

DHCPv6 Server

DHCPSP4

DHCP Snooping

DHCPSP6

DHCPv6 Snooping

DIAG

Diagnosis

DLDP

Device Link Detection Protocol

DOT1X

802.1X

DRNI

Distributed Resilient Network Interconnect

EDEV

Extended-Device Management

ERPS

Ethernet Ring Protection Switching

ETHOAM

Ethernet Operation, Administration and Maintenance

EVB

Edge Virtual Bridging

EVIISIS

Ethernet Virtual Interconnect Intermediate System-to-Intermediate System

FCLINK

Fibre Channel Link

FCOE

Fibre Channel Over Ethernet

FCZONE

Fibre Channel Zone

FIB

Forwarding Information Base

FILTER

Filter

FIPS

FIP Snooping

FTPD

File Transfer Protocol Daemon

HA

High Availability

HQOS

Hierarchical QoS

HTTPD

Hypertext Transfer Protocol Daemon

IFNET

Interface Net Management

IKE

Internet Key Exchange

IPSEC

IP Security

IPSG

IP Source Guard

IRDP

ICMP Router Discovery Protocol

ISIS

Intermediate System-to-Intermediate System

ISSU

In-Service Software Upgrade

L2TP

Layer 2 Tunneling Protocol

L2VPN

Layer 2 VPN

LAGG

Link Aggregation

LDP

Label Distribution Protocol

LLDP

Link Layer Discovery Protocol

LOAD

Load Management

LOGIN

Login

LPDT

Loopback Detection

LS

Local Server

LSPV

LSP Verification

MAC

Media Access Control

MACA

MAC Authentication

MACSEC

MAC Security

MBFD

MPLS BFD

MBUF

Memory buffer

MDC

Multitenant Device Context

MFIB

Multicast Forwarding Information Base

MGROUP

Mirroring group

MPLS

Multiprotocol Label Switching

MTLK

Monitor Link

NAT

Network Address Translation

ND

Neighbor Discovery

NETCONF

Network Configuration Protocol

NQA

Network Quality Analyzer

NTP

Network Time Protocol

OBJP

Object Policy

OFP

OpenFlow Protocol

OPENSRC

Open Source

OPTMOD

Optical Module

OSPF

Open Shortest Path First

OSPFV3

Open Shortest Path First Version 3

PBB

Provider Backbone Bridge

PBR

Policy-Based Routing

PCE

Path Computation Element

PEX

Port Extender

PFILTER

Packet Filter

PIM

Protocol Independent Multicast

PING

Packet Internet Groper

PKI

Public Key Infrastructure

PKT2CPU

Packet to CPU

PKTCPT

Packet Capture

PORTSEC

Port Security

PPP

Point to Point Protocol

PWDCTL

Password Control

QOS

Quality of Service

RADIUS

Remote Authentication Dial In User Service

RDDC

Redundancy

RIP

Routing Information Protocol

RIPNG

Routing Information Protocol Next Generation

RM

Routing Management

RRPP

Rapid Ring Protection Protocol

RTM

Real-Time Event Manager

SCM

Service Control Manager

SCRLSP

Static CRLSP

SESSION

Session

SFLOW

Sampler Flow

SHELL

Shell

SLSP

Static LSP

SMLK

Smart Link

SNMP

Simple Network Management Protocol

SSHS

Secure Shell Server

STAMGR

Station Management

STM

Stack Topology Management

STP

Spanning Tree Protocol

SYSEVENT

System Event

SYSLOG

System Log

TACACS

Terminal Access Controller Access Control System

TELNETD

Telnet Daemon

TRILL

Transparent Interconnect of Lots of Links

VCF

Vertical Converged Framework

VLAN

Virtual Local Area Network

VRRP

Virtual Router Redundancy Protocol

VSRP

Virtual Service Redundancy Protocol

VXLAN

Virtual eXtensible LAN

WIPS

Wireless Intrusion Prevention System

 

Using this document

This document categorizes system log messages by software module. The modules are ordered alphabetically. Except for OPENSRC, the system log messages for each module are listed in alphabetic order of their mnemonic names. The OPENSRC messages are unordered because they use the same mnemonic name (SYSLOG). For each OPENSRC message, the section title uses a short description instead of the mnemonic name.

This document explains messages in tables. Table 5 describes information provided in these tables.

Table 5 Message explanation table contents

Item

Content

Example

Message text

Presents the message description.

ACL [UINT32] [STRING] [UINT64] packet(s).

Variable fields

Briefly describes the variable fields in the order that they appear in the message text.

The variable fields are numbered in the "$Number" form to help you identify their location in the message text.

$1: ACL number.

$2: ID and content of an ACL rule.

$3: Number of packets that matched the rule.

Severity level

Provides the severity level of the message.

6

Example

Provides a real message example. The examples do not include the "<PRI>TIMESTAMP Sysname %%vendor" part or the "Prefix TIMESTAMP Sysname" part, because information in this part varies with system settings.

ACL/6/ACL_STATIS_INFO: ACL 2000 rule 0 permit source 1.1.1.1 0 logging 10000 packet(s).

Explanation

Explains the message, including the event or error cause.

Number of packets that matched an ACL rule. This message is sent when the packet counter changes.

Recommended action

Provides recommended actions. For informational messages, no action is required.

No action is required.

 

AAA messages

This section contains AAA messages.

AAA_FAILURE

Message text

-AAAType=[STRING]-AAADomain=[STRING]-Service=[STRING]-UserName=[STRING]; AAA failed.

Variable fields

$1: AAA type.

$2: AAA scheme.

$3: Service.

$4: Username.

Severity level

5

Example

AAA/5/AAA_FAILURE: -AAAType=AUTHOR-AAADomain=domain1-Service=login-UserName=cwf@system; AAA failed.

Explanation

An AAA request was rejected.

The following are the common reasons:

·     No response was received from the server.

·     The username or password was incorrect.

·     The service type that the user applied for was incorrect.

Recommended action

1.     Verify that the device is correctly connected to the server.

2.     Enter the correct username and password.

3.     Verify that the server settings are the same as the settings on the device.

4.     If the problem persists, contact H3C Support.

 

AAA_LAUNCH

Message text

-AAAType=[STRING]-AAADomain=[STRING]-Service=[STRING]-UserName=[STRING]; AAA launched.

Variable fields

$1: AAA type.

$2: AAA scheme.

$3: Service.

$4: Username.

Severity level

6

Example

AAA/6/AAA_LAUNCH: -AAAType=AUTHEN-AAADomain=domain1-Service=login-UserName=cwf@system; AAA launched.

Explanation

An AAA request was received.

Recommended action

No action is required.

 

AAA_SUCCESS

Message text

-AAAType=[STRING]-AAADomain=[STRING]-Service=[STRING]-UserName=[STRING]; AAA succeeded.

Variable fields

$1: AAA type.

$2: AAA scheme.

$3: Service.

$4: Username.

Severity level

6

Example

AAA/6/AAA_SUCCESS: -AAAType=AUTHOR-AAADomain=domain1-Service=login-UserName=cwf@system; AAA succeeded.

Explanation

An AAA request was accepted.

Recommended action

No action is required.

 

ACL messages

This section contains ACL messages.

ACL_ACCELERATE_NO_RES

Message text

Failed to accelerate [STRING] ACL [UINT32]. The resources are insufficient.

Variable fields

$1: ACL type.

$2: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NO_RES: Failed to accelerate IPv6 ACL 2001. The resources are insufficient.

Explanation

Hardware resources were insufficient for accelerating an ACL.

Recommended action

Delete some rules or disabled ACL acceleration for other ACLs to release hardware resources.

 

ACL_ACCELERATE_NONCONTIGUOUSMASK

Message text

Failed to accelerate ACL [UINT32]. ACL acceleration supports only contiguous wildcard masks.

Variable fields

$1: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NONCONTIGUOUSMASK: Failed to accelerate ACL 2001. ACL acceleration supports only contiguous wildcard masks.

Explanation

ACL acceleration failed because rules containing noncontiguous wildcard masks exist in the ACL.

Recommended action

Check the ACL rules and delete the unsupported configuration.

 

ACL_ACCELERATE_NOT_SUPPORT

Message text

Failed to accelerate [STRING] ACL [UINT32]. The operation is not supported.

Variable fields

$1: ACL type.

$2: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NOT_SUPPORT: Failed to accelerate IPv6 ACL 2001. The operation is not supported.

Explanation

ACL acceleration failed because the system does not support ACL acceleration.

Recommended action

No action is required.

 

ACL_ACCELERATE_NOT_SUPPORTHOPBYHOP

Message text

Failed to accelerate IPv6 ACL [UINT32]. ACL acceleration does not support the rules that contain the hop-by-hop keywords.

Variable fields

$1: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NOT_SUPPORTHOPBYHOP: Failed to accelerate IPv6 ACL 2001. ACL acceleration does not support the rules that contain the hop-by-hop keywords.

Explanation

ACL acceleration failed for the IPv6 ACL because rules containing the hop-by-hop keyword exist in the ACL.

Recommended action

Check the ACL rules and delete the unsupported configuration.

 

ACL_ACCELERATE_NOT_SUPPORTMULTITCPFLAG

Message text

Failed to accelerate IPv6 ACL [UINT32]. ACL acceleration does not support specifying multiple TCP flags in one rule.

Variable fields

$1: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_NOT_SUPPORTMULTITCPFLAG: Failed to accelerate IPv6 ACL 2001. ACL acceleration does not support specifying multiple TCP flags in one rule.

Explanation

ACL acceleration failed for the IPv6 ACL because rules containing multiple TCP flags exist in the ACL.

Recommended action

Check the ACL rules and delete the unsupported configuration.

 

ACL_ACCELERATE_UNK_ERR

Message text

Failed to accelerate [STRING] ACL [UINT32].

Variable fields

$1: ACL type.

$2: ACL number.

Severity level

4

Example

ACL/4/ACL_ACCELERATE_UNK_ERR: Failed to accelerate IPv6 ACL 2001.

Explanation

ACL acceleration failed because of an unknown error.

Recommended action

No action is required.

 

ACL_IPV6_STATIS_INFO

Message text

IPv6 ACL [UINT32] [STRING] [UINT64] packet(s).

Variable fields

$1: ACL number.

$2: ID and content of an IPv6 ACL rule.

$3: Number of packets that matched the rule.

Severity level

6

Example

ACL6/6/ACL_IPV6_STATIS_INFO: IPv6 ACL 2000 rule 0 permit source 1:1::/64 logging 1000 packet(s).

Explanation

The number of packets matching the IPv6 ACL rule changed.

Recommended action

No action is required.

 

ACL_NO_MEM

Message text

Failed to configure [STRING] ACL [UINT] due to lack of memory.

Variable fields

$1: ACL type.

$2: ACL number.

Severity level

3

Example

ACL/3/ACL_NO_MEM: Failed to configure ACL 2001 due to lack of memory.

Explanation

Configuring the ACL failed because memory is insufficient.

Recommended action

Use the display memory-threshold command to check the memory usage.

 

ACL_STATIS_INFO

Message text

ACL [UINT32] [STRING] [UINT64] packet(s).

Variable fields

$1: ACL number.

$2: ID and content of an IPv4 ACL rule.

$3: Number of packets that matched the rule.

Severity level

6

Example

ACL/6/ACL_STATIS_INFO: ACL 2000 rule 0 permit source 1.1.1.1 0 logging 10000 packet(s).

Explanation

The number of packets matching the IPv4 ACL rule changed.

Recommended action

No action is required.

 

ANCP messages

This section contains ANCP messages.

ANCP_INVALID_PACKET

Message text

-NeighborName=[STRING]-State=[STRING]-MessageType=[STRING]; The [STRING] value [STRING] is wrong, and the value [STRING] is expected.

Variable fields

$1: ANCP neighbor name.

$2: Neighbor state.

$3: Message type.

$4: Field.

$5: Wrong value of the field.

$6: Expected value of the field.

Severity level

6

Example

ANCP/6/ANCP_INVALID_PACKET: -NeighborName=Dslam-State=SYNSENT-MessageType=SYNACK; The Sender Instance value 0 is wrong, and the value 1 is expected.

Explanation

The system received an adjacency message that had a field with a wrong value.

Recommended action

No action is required.

 

APMGR messages

This section contains access point management messages.

APMGR_AC_MEM_ALERT

Message text

The memory utilization has reached the threshold.

Variable fields

N/A

Severity level

4

Example

APMGR/4/APMGR_AC_MEM_ALERT: The memory utilization has reached the threshold.

Explanation

The AP failed to come online because the memory utilization exceeded the limit.

Recommended action

Stop creating manual APs and prevent APs from coming online.

 

APMGR_ADD_AP_FAIL

Message text

AP [STRING] failed to come online using serial ID [STRING]: MAC address [STRING] is being used by AP [STRING].

Variable fields

$1: AP name.

$2: Serial ID.

$3: MAC address.

$4: AP name.

Severity level

4

Example

APMGR/4/ APMGR_ADD_AP_FAIL: AP ap1 failed to come online using serial ID 01247ef96: MAC address 0023-7961-5201 is being used by AP ap2.

Explanation

The AP failed to come online because a manual AP that has the same MAC address already exists on the AC.

Recommended action

Delete either the manual AP that has the MAC address or the serial ID.

 

APMGR_ADDBAC_INFO

Message text

Add BAS AC [STRING].

Variable fields

$1: MAC address of the BAS AC.

Severity level

6

Example

APMGR/6/APMGR_ADDBAC_INFO: Add BAS AC 3ce5-a616-28cd.

Explanation

The BAS AC was connected to the master AC.

Recommended action

No action is required.

 

APMGR_AP_OFFLINE

Message text

AP [STRING] went offline. State changed to Idle.

Variable fields

$1: AP name.

Severity level

6

Example

APMGR/6/APMGR_AP_OFFLINE: AP ap1 went offline. State changed to Idle.

Explanation

The AP went offline. The state of the AP changed to Idle.

Recommended action

If the AP went offline abnormally, check the debugging information to locate the issue and resolve it.

 

APMGR_AP_ONLINE

Message text

AP [STRING] went online. State changed to Run.

Variable fields

$1: AP name.

Severity level

6

Example

APMGR/6/APMGR_AP_ONLINE: AP ap1 went online. State changed to Run.

Explanation

The AP came online. The state of the AP changed to Run.

Recommended action

No action is required.

 

APMGR_CWC_IMG_DOWNLOAD_COMPLETE

Message text

System software image file [STRING] downloading through the CAPWAP tunnel to AC [STRING] completed.

Variable fields

$1: Image file name.

$2: AC IP address.

Severity level

6

Example

APMGR/6/APMGR_CWC_IMG_DOWNLOAD_COMPLETE: System software image file 5800.ipe downloading through the CAPWAP tunnel to AC 192.168.10.1 completed.

Explanation

The AP downloaded the image file from the AC successfully.

Recommended action

No action is required.

 

APMGR_CWC_IMG_DOWNLOAD_START

Message text

Started to download the system software image file [STRING] through the CAPWAP tunnel to AC [STRING].

Variable fields

$1: Image file name.

$2: AC IP address.

Severity level

6

Example

APMGR/6/APMGR_CWC_IMG_DOWNLOAD_START: Started to download the system software image file 5800.ipe through the CAPWAP tunnel to AC 192.168.10.1.

Explanation

The AP started to download the image file from the AC.

Recommended action

Make sure the AP is correctly connected to the AC.

 

APMGR_CWC_IMG_NO_ENOUGH_SPACE

Message text

Insufficient flash memory space for downloading system software image file [STRING].

Variable fields

$1: Image file name.

Severity level

6

Example

APMGR/6/APMGR_CWC_IMG_NO_ENOUGH_SPACE: Insufficient flash memory space for downloading system software image file 5800.ipe.

Explanation

The AP failed to download the image file from the AC because of insufficient flash memory.

Recommended action

Delete files not in use from the AP.

 

APMGR_CWC_LOCAL_AC_DOWN

Message text

CAPWAP tunnel to Central AC [STRING] went down. Reason: [STRING].

Variable fields

$1: IP address of the central AC.

$2: Reason:

·     Added local AC IP address.

·     Deleted local AC IP address.

·     Local AC interface used for CAPWAP tunnel went down.

·     Local AC config changed.

·     N/A

Severity level

4

Example

APMGR/4/APMGR_CWC_LOCAL_AC_DOWN: CAPWAP tunnel to Central AC 2.2.2.1 went down. Reason: Added local AC IP address.

Explanation

The CAPWAP tunnel between the central AC and the local AC was terminated for a specific reason.

Recommended action

To resolve the issue:

1.     Examine the network connection between the central AC and the local AC.

2.     Verify that the central AC is correctly configured.

3.     Verify that the local AC is correctly configured.

4.     If the issue persists, contact H3C Support.

 

APMGR_CWC_LOCAL_AC_UP

Message text

CAPWAP tunnel to Central AC [STRING] went up.

Variable fields

$1: IP address of the central AC.

Severity level

6

Example

APMGR/6/APMGR_CWC_LOCAL_AC_UP: CAPWAP tunnel to Central AC 2.2.2.1 went up.

Explanation

The central AC has established a CAPWAP tunnel with the local AC.

Recommended action

No action is required.

 

APMGR_CWC_REBOOT

Message text

AP in state [STRING] is rebooting. Reason: [STRING]

Variable fields

$1: AP state.

$2: Reason:

·     AP was reset.

·     Image was downloaded successfully.

·     AP stayed in idle state for a long time.

Severity level

6

Example

APMGR/6/APMGR_CWC_REBOOT: AP in State Run is rebooting. Reason: AP was reset.

Explanation

The AP rebooted for a specific reason.

Recommended action

No action is required.

 

APMGR_CWC_RUN_DOWNLOAD_COMPLETE

Message text

File [STRING] successfully downloaded through the CAPWAP tunnel to AC [STRING].

Variable fields

$1: File name.

$2: AC IP address.

Severity level

6

Example

APMGR/6/APMGR_CWC_RUN_DOWNLOAD_COMPLETE: File ac.cfg successfully downloaded through the CAPWAP tunnel to AC 192.168.10.1.

Explanation

The AP downloaded the file from the AC successfully.

Recommended action

No action is required.

 

APMGR_CWC_RUN_DOWNLOAD_START

Message text

Started to download the file [STRING] through the CAPWAP tunnel to AC [STRING].

Variable fields

$1: File name.

$2: AC IP address.

Severity level

6

Example

APMGR/6/APMGR_CWC_RUN_DOWNLOAD_START: Started to download the file ac.cfg through the CAPWAP tunnel to AC 192.168.10.1.

Explanation

The AP started to download the file from the AC.

Recommended action

Make sure the AP is correctly connected to the AC.

 

APMGR_CWC_RUN_NO_ENOUGH_SPACE

Message text

Insufficient flash memory space for downloading file [STRING].

Variable fields

$1: File name.

Severity level

6

Example

APMGR/6/APMGR_CWC_RUN_NO_ENOUGH_SPACE: Insufficient flash memory space for downloading file ac.cfg.

Explanation

The AP failed to download the file from the AC because of insufficient flash memory.

Recommended action

Delete files not in use from the AP.

 

APMGR_CWC_TUNNEL_DOWN

Message text

CAPWAP tunnel to AC [STRING] went down. Reason: [STRING].

Variable fields

$1: AC IP address.

$2: Reason:

·     Added AP IP address.

·     Deleted AP IP address.

·     AP interface used for CAPWAP tunnel went down.

·     AP config changed.

·     AP was reset.

·     Number of echo retransmission attempts exceeded the limit.

·     Full retransmission queue.

·     Data channel timer expired.

·     Backup AC IP address changed.

·     Backup tunnel changed to master tunnel.

·     Failed to change backup tunnel to master tunnel.

·     Backup method changed.

·     N/A.

Severity level

6

Example

APMGR/6/APMGR_CWC_TUNNEL_DOWN: CAPWAP tunnel to AC 192.168.10.1 went down. Reason: AP was reset.

Explanation

The CAPWAP tunnel between the AP and the AC was terminated for a specific reason.

Recommended action

Examine the network connection between the AP and the AC.

 

APMGR_CWC_TUNNEL_UP

Message text

[STRING] CAPWAP tunnel to AC [STRING] went up.

Variable fields

$1: Tunnel type:

·     Master.

·     Backup.

$2: AC IP address.

Severity level

6

Example

APMGR/6/APMGR_CWC_TUNNEL_UP: Master CAPWAP tunnel to AC 192.168.10.1 went up.

Explanation

The AP was connected to the AC successfully and entered Run state.

Recommended action

No action is required.

 

APMGR_CWS_IMG_DOWNLOAD_COMPLETE

Message text

System software image file [STRING] downloading through the CAPWAP tunnel for AP [STRING] completed.

Variable fields

$1: Image file name.

$2: AP name.

Severity level

6

Example

APMGR/6/APMGR_ CWS_IMG_DOWNLOAD_COMPLETE: System software image file 5800.ipe downloading through the CAPWAP tunnel for AP ap2 completed.

Explanation

The AP downloaded the image file from the AC successfully.

Recommended action

No action is required.

 

APMGR_CWS_IMG_DOWNLOAD_START

Message text

AP [STRING] started to download the system software image file [STRING].

Variable fields

$1: AP name.

$2: Image file name.

Severity level

6

Example

APMGR/6/APMGR_CWS_IMG_DOWNLOAD_START: AP ap1 started to download the system software image file 5800.ipe.

Explanation

The AP started to download the image file from the AC.

Recommended action

No action is required.

 

APMGR_CWS_LOCAL_AC_DOWN

Message text

CAPWAP tunnel to local AC [STRING] went down. Reason: [STRING].

Variable fields

$1: IP address of the local AC.

$2: Reason:

·     Neighbor dead timer expired.

·     Local AC was deleted.

·     Serial number changed.

·     Processed join request in Run state.

·     Failed to retransmit message.

·     N/A

Severity level

4

Example

APMGR/4/APMGR_CWS_LOCAL_AC_DOWN: CAPWAP tunnel to local AC 1.1.1.1 went down. Reason: Serial number changed.

Explanation

The CAPWAP tunnel between the central AC and the local AC was terminated for a specific reason.

Recommended action

To resolve the issue:

1.     Examine the network connection between the central AC and the local AC.

2.     Verify that the central AC is correctly configured.

3.     Verify that the local AC is correctly configured.

4.     If the issue persists, contact H3C Support.

 

APMGR_CWS_LOCAL_AC_UP

Message text

CAPWAP tunnel to local AC [STRING] went up.

Variable fields

$1: IP address of the local AC.

Severity level

6

Example

APMGR/6/APMGR_CWS_LOCAL_AC_UP: CAPWAP tunnel to local AC 1.1.1.1 went up.

Explanation

The central AC has established a CAPWAP tunnel with the local AC.

Recommended action

No action is required.

 

APMGR_CWS_RUN_DOWNLOAD_COMPLETE

Message text

File [STRING] successfully downloaded through the CAPWAP tunnel for AP [STRING].

Variable fields

$1: File name.

$2: AP name.

Severity level

6

Example

APMGR/6/APMGR_CWS_RUN_DOWNLOAD_COMPLETE: File ac.cfg successfully downloaded through the CAPWAP tunnel for AP ap2.

Explanation

The AP downloaded the file from the AC successfully.

Recommended action

No action is required.

 

APMGR_CWS_RUN_DOWNLOAD_START

Message text

AP [STRING] started to download the file [STRING].

Variable fields

$1: AP name.

$2: File name.

Severity level

6

Example

APMGR/6/APMGR_CWS_RUN_DOWNLOAD_START: AP ap1 started to download the file ac.cfg.

Explanation

The AP started to download the file from the AC.

Recommended action

No action is required.

 

APMGR_CWS_TUNNEL_DOWN

Message text

CAPWAP tunnel to AP [STRING] went down. Reason: [STRING].

Variable fields

$1: AP name.

$2: Reason:

·     Neighbor dead timer expired.

·     AP was reset.

·     AP was deleted.

·     Serial number changed.

·     Processed join request in Run state.

·     Failed to retransmit message.

·     Received WTP tunnel down event from AP.

·     Backup AC closed the backup tunnel.

·     Tunnel switched.

·     N/A.

Severity level

6

Example

APMGR/6/APMGR_CWS_TUNNEL_DOWN: CAPWAP tunnel to AP ap1 went down. Reason: AP was reset.

Explanation

The AP went offline for a specific reason.

Recommended action

To resolve the issue:

1.     Examine the network connection between the AP and the AC.

2.     Verify that the AP is correctly configured.

3.     Verify that the AC is correctly configured.

4.     If the issue persists, contact H3C Support.

 

APMGR_CWS_TUNNEL_UP

Message text

[STRING] CAPWAP tunnel to AP [STRING] went up.

Variable fields

$1: Tunnel type:

·     Master.

·     Backup.

$2: AP name.

Severity level

6

Example

APMGR/6/APMGR_CWS_TUNNEL_UP: Backup CAPWAP tunnel to AP ap1 went up.

Explanation

The AP came online and entered Run state.

Recommended action

No action is required.

 

APMGR_DELBAC_INFO

Message text

Delete BAS AC [STRING].

Variable fields

$1: MAC address of the BAS AC.

Severity level

6

Example

APMGR/6/APMGR_DELBAC_INFO: Delete BAS AC 3ce5-a616-28cd.

Explanation

The BAS AC was disconnected from the master AC.

Recommended action

No action is required.

 

APMGR_LOCAL_AC_OFFLINE

Message text

Local AC [STRING] went offline. State changed to Idle.

Variable fields

$1: Name of the local AC.

Severity level

6

Example

APMGR/6/APMGR_LOCAL_AC_OFFLINE: Local AC ac1 went offline. State changed to Idle.

Explanation

The local AC went offline. The state of the local AC changed to Idle.

Recommended action

1.     If the local AC went offline abnormally, check the debugging information to locate the issue and resolve it.

2.     If the issue persists, contact H3C Support.

 

APMGR_LOCAL_AC_ONLINE

Message text

Local AC [STRING] went online. State changed to Run.

Variable fields

$1: Name of the local AC.

Severity level

6

Example

APMGR/6/APMGR_LOCAL_AC_ONLINE: Local AC ac1 went online. State changed to Run.

Explanation

The local AC came online. The state of the local AC changed to Run.

Recommended action

No action is required.

 

ARP messages

This section contains ARP messages.

ARP_ACTIVE_ACK_NO_REPLY

Message text

No ARP reply from IP [STRING] was received on interface [STRING].

Variable fields

$1: IP address.

$2: Interface name.

Severity level

6

Example

ARP/6/ARP_ACTIVE_ACK_NO_REPLY: No ARP reply from IP 192.168.10.1 was received on interface GigabitEthernet1/0/1.

Explanation

The ARP active acknowledgement feature did not receive an ARP reply after it sent an ARP request to the sender IP of an ARP message.

This message indicates the risk of attacks.

Recommended action

1.     Verify that the learned ARP entries on the device are consistent with the existing legal devices. When gateways and servers are on the network, check the ARP entries for these devices first.

2.     If the ARP entries are correct and the attack continues, contact H3C Support.

 

ARP_ACTIVE_ACK_NOREQUESTED_REPLY

Message text

Interface [STRING] received from IP [STRING] an ARP reply that was not requested by the device.

Variable fields

$1: Interface name.

$2: IP address.

Severity level

6

Example

ARP/6/ARP_ACTIVE_ACK_NOREQUESTED_REPLY: Interface GigabitEthernet1/0/1 received from IP 192.168.10.1 an ARP reply that was not requested by the device.

Explanation

The ARP active acknowledgement feature received an unsolicited ARP reply from a sender IP.

This message indicates the risk of attacks.

Recommended action

No action is required. The device discards the ARP reply automatically.

 

ARP_BINDRULETOHW_FAILED

Message text

Failed to download binding rule to hardware on the interface [STRING], SrcIP [IPADDR], SrcMAC [MAC], VLAN [UINT16], Gateway MAC [MAC].

Variable fields

$1: Interface name.

$2: Source IP address.

$3: Source MAC address.

$4: VLAN ID.

$5: Gateway MAC address.

Severity level

5

Example

ARP/5/ARP_BINDRULETOHW_FAILED: Failed to download binding rule to hardware on the interface Ethernet1/0/1, SrcIP 1.1.1.132, SrcMAC 0015-E944-A947, VLAN 1, Gateway MAC 00A1-B812-1108.

Explanation

The system failed to set a binding rule to the hardware on an interface. The message is sent in any of the following situations:

·     The resources are not sufficient for the operation.

·     The memory is not sufficient for the operation.

·     A hardware error occurs.

Recommended action

To resolve the problem:

1.     Execute the display qos-acl resource command to check if the ACL resources for the operation are sufficient.

¡     If yes, proceed to step 2.

¡     If no, delete unnecessary configuration to release ACL resources. If no configuration can be deleted, proceed to step 2.

2.     Execute the display memory command to check if the memory for the operation is sufficient.

¡     If yes, proceed to step 3.

¡     If no, delete unnecessary configuration to release memory. If no configuration can be deleted, proceed to step 3.

3.     Delete the configuration and perform the operation again.

 

ARP_DETECTION_LOG

Message text

Detected an ARP attack on interface [STRING]: IP [STRING], MAC [STRING], VLAN [STRING]. [UINT32] packet(s) dropped.

Variable fields

$1: Interface name.

$2: IP address.

$3: MAC address.

$4: VLAN ID.

$5: Number of dropped packets.

Severity level

5

Example

ARP/5/ARP_INSPECTION: -MDC=1; Detected an ARP attack on interface GigabitEthernet1/0/1: IP 1.1.1.1, MAC 0001-0001-0001, VLAN 100. 2 packet(s) dropped.

Explanation

An ARP attack was detected on an interface and attack packets were dropped.

Recommended action

Check the source of the ARP attack.

 

ARP_DUPLICATE_IPADDR_DETECT

Message text

Detected an IP address conflict. The device with MAC address [STRING] connected to interface [STRING] in VSI [STRING] and the device with MAC address [STRING] connected to interface [STRING] in VSI [STRING] were using the same IP address [IPADDR].

Variable fields

$1: MAC address.

$2: Interface name. (The interface can be a tunnel interface, Layer 3 interface, or Ethernet service instance.)

$3: VSI name.

$4: MAC address.

$5: Interface name. (The interface can be a tunnel interface, Layer 3 interface, or Ethernet service instance.)

$6: VSI name.

$7: Conflicting IP address.

Severity level

6

Example

ARP/6/ARP_DUPLICATE_IPADDR_DETECT: Detected an IP address conflict. The device with MAC address 00-00-01 connected to interface GigabitEthernet1/0/1 service-instance 1000 in VSI vpna and the device with MAC address 0011-0011-0002 connected to interface tunnel 10 in VSI vpna were using the same IP address 192.168.1.1.

Explanation

This message is sent when an interface receives an ARP message in which the sender information conflicts with an existing ARP entry. The sender IP address is the same as the IP address in the entry, but the MAC addresses are different.

Recommended action

Change the IP address on either of the two devices.

 

ARP_DYNAMIC

Message text

The maximum number of dynamic ARP entries for the device reached.

Variable fields

N/A

Severity level

6

Example

ARP/6/ ARP_DYNAMIC_IF: The maximum number of dynamic ARP entries for interface GigabitEthernet1/0/1 reached.

Explanation

The maximum number of dynamic ARP entries for the device was reached.

Recommended action

No action is required.

 

ARP_DYNAMIC_IF

Message text

The maximum number of dynamic ARP entries for interface [STRING] reached.

Variable fields

$1: Interface name.

Severity level

6

Example

The maximum number of dynamic ARP entries for interface GigabitEthernet3/0/1 reached.

Explanation

This message is sent when the maximum number of dynamic ARP entries for the specified interface is reached.

Recommended action

No action is required.

 

ARP_DYNAMIC_SLOT

Message text

(Distributed devices in standalone mode.) (Centralized IRF devices.) The maximum number of dynamic ARP entries for slot [UINT32] reached.

(Distributed devices in IRF mode.) The maximum number of dynamic ARP entries for chassis [UINT32] slot [UINT32] reached.

Variable fields

$1: Slot number. (Distributed devices in standalone mode.)

$1: Member device ID. (Centralized IRF devices.)

$2: Member device ID. (Distributed devices in IRF mode.)

$3: Slot number. (Distributed devices in IRF mode.)

Severity level

6

Example

ARP/6/ARP_DYNAMIC_SLOT: The maximum number of dynamic ARP entries for slot 2 reached.

ARP/6/ARP_DYNAMIC_SLOT: The maximum number of dynamic ARP entries for chassis 1 slot 2 reached.

Explanation

The maximum number of dynamic ARP entries for the card was reached. (Distributed devices in standalone mode.)

The maximum number of dynamic ARP entries for the member device was reached. (Centralized IRF devices.)

The maximum number of dynamic ARP entries for the card on the member device was reached. (Distributed devices in IRF mode.)

Recommended action

No action is required.

 

ARP_ENTRY_CONFLICT

Message text

The software entry for [STRING] on [STRING] and the hardware entry did not have the same [STRING].

Variable fields

$1: IP address.

$2: VPN instance name. If the ARP entry belongs to the public network, this field displays the public network.

$3: Inconsistent items:

¡     MAC address.

¡     output interface.

¡     output port.

¡     outermost layer VLAN ID.

¡     second outermost layer VLAN ID.

¡     VSI index.

¡     link ID.

Severity level

6

Example

ARP/6/ARP_ENTRY_CONFLICT: The software entry for 1.1.1.1 on the VPN a and the hardware entry did not have the same MAC address, output port, VSI index, and link ID.

ARP/6/ARP_ENTRY_CONFLICT: The software entry for 1.1.1.2 on the public  network and the hardware entry did not have the same MAC address, output port, VSI index, and link ID.

Explanation

The software entry for the specified IP address is not the same as the hardware entry. For example, they do not have the same output interface.

Recommended action

No action is required. ARP automatically refreshes the hardware entries.

 

ARP_HOST_IP_CONFLICT

Message text

The host [STRING] connected to interface [STRING] cannot communicate correctly, because it uses the same IP address as the host connected to interface [STRING].

Variable fields

$1: IP address.

$2: Interface name.

$3: Interface name.

Severity level

4

Example

ARP/4/ARP_HOST_IP_CONFLICT: The host 1.1.1.1 connected to interface GigabitEthernet1/0/1 cannot communicate correctly, because it uses the same IP address as the host connected to interface GigabitEthernet1/0/2.

Explanation

The sender IP address in a received ARP message conflicted with the IP address of a host connected to another interface.

Recommended action

Check whether the hosts that send the ARP messages are legitimate. Disconnect the illegal host from the network.

 

ARP_MAXIMUM_DEVICE

Message text

Maximum number of ARP entries on the device is reached.

Variable fields

N/A

Severity level

6

Example

ARP/6/ARP_MAXIMUM_DEVICE: Maximum number of ARP entries on the device is reached.

Explanation

This message is sent when the maximum number of all ARP entries is reached on the device.

Recommended action

No action is required.

 

ARP_LOCALPROXY_ENABLE_FAILED

Message text

Failed to enable local proxy ARP on interface [STRING].

Variable fields

$1: Interface name.

Severity level

4

Example

ARP/4/ARP_LOCALPROXY_ENABLE_FAILED: -MDC=1-Slot=2; Failed to enable local proxy ARP on interface VSI-interface 1.

Explanation

This message is sent when the device fails to enable local proxy ARP on an interface in a slot. If the interface resides on the MPU, the slot number is 0.

Recommended action

1.     Verify that the card supports local proxy ARP.

2.     Verify that sufficient hardware resources are available.

 

ARP_RATE_EXCEEDED

Message text

The ARP packet rate ([UINT32] pps) exceeded the rate limit ([UINT32] pps) on interface [STRING] in the last [UINT32] seconds.

Variable fields

$1: ARP packet rate.

$2: ARP limit rate.

$3: Interface name.

$4: Interval time.

Severity level

4

Example

ARP/4/ARP_RATE_EXCEEDED: The ARP packet rate (100 pps) exceeded the rate limit (80 pps) on interface GigabitEthernet1/0/1 in the last 10 seconds.

Explanation

An interface received ARP messages at a higher rate than the rate limit.

Recommended action

Verify that the hosts at the sender IP addresses are legitimate.

 

ARP_SENDER_IP_INVALID

Message text

Sender IP [STRING] was not on the same network as the receiving interface [STRING].

Variable fields

$1: IP address.

$2: Interface name.

Severity level

6

Example

ARP/6/ARP_SENDER_IP_INVALID: Sender IP 192.168.10.2 was not on the same network as the receiving interface GigabitEthernet1/0/1.

Explanation

The sender IP of a received ARP message was not on the same network as the receiving interface.

Recommended action

Verify that the host at the sender IP address is legitimate.

 

ARP_SENDER_MAC_INVALID

Message text

Sender MAC [STRING] was not identical to Ethernet source MAC [STRING] on interface [STRING].

Variable fields

$1: MAC address.

$2: MAC address.

$3: Interface name.

Severity level

6

Example

ARP/6/ARP_SENDER_MAC_INVALID: Sender MAC 0000-5E14-0E00 was not identical to Ethernet source MAC 0000-5C14-0E00 on interface GigabitEthernet1/0/1.

Explanation

An interface received an ARP message. The sender MAC address in the message body was not identical to the source MAC address in the Ethernet header.

Recommended action

Verify that the host at the sender MAC address is legitimate.

 

ARP_SENDER_SMACCONFLICT

Message text

Packet was discarded because its sender MAC address was the MAC address of the receiving interface.

Interface: [STRING], sender IP: [STRING], target IP: [STRING].

Variable fields

$1: Interface name.

$2: Sender IP address.

$3: Target IP address.

Severity level

6

Example

ARP/6/ARP_SENDER_SMACCONFLICT: Packet discarded for the sender MAC address is the same as the receiving interface.

Interface: GigabitEthernet1/0/1 sender IP: 1.1.2.2 target IP: 1.1.2.1,

Explanation

The sender MAC address of a received ARP packet conflicts with the MAC address of the device.

Recommended action

No action is required.

 

ARP_SENDER_SMACCONFLICT_VSI

Message text

Packet was discarded because its sender MAC address was the MAC address of the receiving interface.

Interface: [STRING], sender IP: [STRING], target IP: [STRING],VSI index: [UINT32], link ID: [UINT32].

Variable fields

$1: Interface name.

$2: Sender IP address.

$3: Target IP address.

$4: VSI index.

$5: Link ID.

Severity level

6

Example

ARP/6/ARP_SENDER_SMACCONFLICT_VSI: Packet discarded for the sender MAC address is the same as the receiving interface.

Interface: VSI3 sender IP: 1.1.2.2 target IP: 1.1.2.1, VSI Index: 2, Link ID: 0

Explanation

The sender MAC address of a received ARP packet conflicts with the MAC address of the device. The receiving interface is a VSI interface.

Recommended action

No action is required.

 

ARP_SRC_MAC_FOUND_ATTACK

Message text

An attack from MAC [STRING] was detected on interface [STRING].

Variable fields

$1: MAC address.

$2: Interface name.

Severity level

6

Example

ARP/6/ARP_SRC_MAC_FOUND_ATTACK: An attack from MAC 0000-5E14-0E00 was detected on interface GigabitEthernet1/0/1.

Explanation

The source MAC-based ARP attack detection feature received more ARP packets from the same MAC address within 5 seconds than the specified threshold.

This message indicates the risk of attacks.

Recommended action

Verify that the host at the source MAC address is legitimate.

 

ARP_SUP_ENABLE_FAILED

Message text

Failed to enable ARP flood suppression on VSI [string].

Variable fields

$1: VSI name.

Severity level

4

Example

ARP/4/ARP_SUP_ENABLE_FAILED: -MDC=1; Failed to enable ARP flood suppression on VSI vpna.

Explanation

This message is sent when the system failed to enable ARP flood suppression for a VSI. The minimum interval between two log messages is 2 seconds. To prevent the system from failing to send the message, wait for a minimum of 2 seconds before you enable ARP flood suppression for another VSI.

Recommended action

1.     Verify that the device supports ARP flood suppression.

2.     Verify that the hardware resources are sufficient.

 

ARP_TARGET_IP_INVALID

Message text

Target IP [STRING] was not the IP of the receiving interface [STRING].

Variable fields

$1: IP address.

$2: Interface name.

Severity level

6

Example

ARP/6/ARP_TARGET_IP_INVALID: Target IP 192.168.10.2 was not the IP of the receiving interface GigabitEthernet1/0/1.

Explanation

The target IP address of a received ARP message was not the IP address of the receiving interface.

Recommended action

Verify that the host at the sender IP address is legitimate.

 

ARP_THRESHOLD_REACHED

Message text

The alarm threshold for dynamic ARP entry learning was reached on interface [STRING].

Variable fields

$1: Interface name.

Severity level

4

Example

ARP/4/ ARP_THRESHOLD_REACHED: The alarm threshold for dynamic ARP entry learning was reached on interface GigabitEthernet1/0/1.

Explanation

This message is sent when the alarm threshold for dynamic ARP learning was reached on an interface.

Recommended action

Verify that the number of learned dynamic ARP entries matches the actual number of devices in the network, and no ARP attack sources exist in the network.

 

DUPIFIP

Message text

Duplicate address [STRING] on interface [STRING], sourced from [STRING].

Variable fields

$1: IP address.

$2: Interface name.

$3: MAC Address.

Severity level

6

Example

ARP/6/DUPIFIP: Duplicate address 1.1.1.1 on interface Ethernet1/1/1, sourced from 0015-E944-A947.

Explanation

ARP detected a duplicate address.

The sender IP in the received ARP packet was being used by the receiving interface.

Recommended action

Modify the IP address configuration.

 

DUPIP

Message text

IP address [STRING] conflicted with global or imported IP address, sourced from [STRING].

Variable fields

$1: IP address.

$2: MAC Address.

Severity level

6

Example

ARP/6/DUPIP: IP address 30.1.1.1 conflicted with global or imported IP address, sourced from 0000-0000-0001.

Explanation

The sender IP address of the received ARP packet conflicted with the global or imported IP address.

Recommended action

Modify the IP address configuration.

 

DUPVRRPIP

Message text

IP address [STRING] conflicted with VRRP virtual IP address on interface [STRING], sourced from [STRING].

Variable fields

$1: IP address.

$2: Interface name.

$3: MAC address.

Severity level

6

Example

ARP/6/DUPVRRPIP: IP address 1.1.1.1 conflicted with VRRP virtual IP address on interface GigabitEthernet1/0/1, sourced from 0015-E944-A947.

Explanation

The sender IP address of the received ARP packet conflicted with the VRRP virtual IP address.

Recommended action

Modify the IP address configuration.

 

ATK messages

This section contains attack detection and prevention messages.

ATK_ICMP_ADDRMASK_REQ

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_REQ: IcmpType(1058)=17; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP address mask request logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_ADDRMASK_REQ_RAW

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_REQ_RAW: IcmpType(1058)=17; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP address mask requests of the same attributes, this message is sent only when the first request is received.

If log aggregation is disabled, this message is sent every time an ICMP address mask request is received.

Recommended action

No action is required.

 

ATK_ICMP_ADDRMASK_REQ_RAW_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_REQ_RAW_SZ: IcmpType(1058)=17; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP address mask requests of the same attributes, this message is sent only when the first request is received.

If log aggregation is disabled, this message is sent every time an ICMP address mask request is received.

Recommended action

No action is required.

 

ATK_ICMP_ADDRMASK_REQ_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_REQ_SZ: IcmpType(1058)=17; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP address mask request logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_ADDRMASK_RPL

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_RPL: IcmpType(1058)=18; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP address mask reply logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_ADDRMASK_RPL_RAW

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_RPL_RAW: IcmpType(1058)=18; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP address mask replies of the same attributes, this message is sent only when the first reply is received.

If log aggregation is disabled, this message is sent every time an ICMP address mask reply is received.

Recommended action

No action is required.

 

ATK_ICMP_ADDRMASK_RPL_RAW_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_RPL_RAW_SZ: IcmpType(1058)=18; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP address mask replies of the same attributes, this message is sent only when the first reply is received.

If log aggregation is disabled, this message is sent every time an ICMP address mask reply is received.

Recommended action

No action is required.

 

ATK_ICMP_ADDRMASK_RPL_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_ADDRMASK_RPL_SZ: IcmpType(1058)=18; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP address mask reply logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_ECHO_REQ

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_ECHO_REQ: IcmpType(1058)=8; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP echo request logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_ECHO_REQ_RAW

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; DstPort(1004)=[UINT16]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Destination port number.

$7: Name of the receiving VPN instance.

$8: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_ECHO_REQ_RAW: IcmpType(1058)=8; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DstPort(1004)=22; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP echo requests of the same attributes, this message is sent only when the first request is received.

If log aggregation is disabled, this message is sent every time an ICMP echo request is received.

Recommended action

No action is required.

 

ATK_ICMP_ECHO_REQ_RAW_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; DstPort(1004)=[UINT16]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Destination port number.

$7: Name of the receiving VPN instance.

$8: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_ECHO_REQ_RAW_SZ: IcmpType(1058)=8; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DstPort(1004)=22; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP echo requests of the same attributes, this message is sent only when the first request is received.

If log aggregation is disabled, this message is sent every time an ICMP echo request is received.

Recommended action

No action is required.

 

ATK_ICMP_ECHO_REQ_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_ECHO_REQ_SZ: IcmpType(1058)=8; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP echo request logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_ECHO_RPL

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_ECHO_RPL: IcmpType(1058)=0; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP echo reply logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_ECHO_RPL_RAW

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_ECHO_RPL_RAW: IcmpType(1058)=0; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP echo replies of the same attributes, this message is sent only when the first reply is received.

If log aggregation is disabled, this message is sent every time an ICMP echo reply is received.

Recommended action

No action is required.

 

ATK_ICMP_ECHO_RPL_RAW_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_ECHO_RPL_RAW_SZ: IcmpType(1058)=0; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP echo replies of the same attributes, this message is sent only when the first reply is received.

If log aggregation is disabled, this message is sent every time an ICMP echo reply is received.

Recommended action

No action is required.

 

ATK_ICMP_ECHO_RPL_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_ECHO_RPL_SZ: IcmpType(1058)=0; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP echo reply logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_FLOOD

Message text

RcvIfName(1023)=[STRING]; DstIPAddr(1007)=[IPADDR]; DstPort(1008)=[UINT16]; RcvVPNInstance(1041)=[STRING]; UpperLimit(1048)=[UINT32]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING].

Variable fields

$1: Receiving interface name.

$2: Destination IP address.

$3: Destination port number.

$4: Name of the receiving VPN instance.

$5: Rate limit.

$6: Actions against the attack.

$7: Start time of the attack.

Severity level

3

Example

ATK/3/ATK_ICMP_FLOOD: RcvIfName(1023)=Ethernet0/0/2; DstIPAddr(1007)=6.1.1.5; DstPort(1008)=22; RcvVPNInstance(1041)=--; UpperLimit(1048)=10; Action(1049)=logging; BeginTime_c(1011)=20131009093351.

Explanation

This message is sent when the number of ICMP packets sent to a destination per second exceeds the rate limit.

Recommended action

No action is required.

 

ATK_ICMP_FLOOD_SZ

Message text

SrcZoneName(1025)=[STRING]; DstIPAddr(1007)=[IPADDR]; DstPort(1008)=[UINT16]; RcvVPNInstance(1041)=[STRING]; UpperLimit(1048)=[UINT32]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING].

Variable fields

$1: Source security zone name.

$2: Destination IP address.

$3: Destination port number.

$4: Name of the receiving VPN instance.

$5: Rate limit.

$6: Actions against the attack.

$7: Start time of the attack.

Severity level

3

Example

ATK/3/ATK_ICMP_FLOOD_SZ: SrcZoneName(1025)=Trust; DstIPAddr(1007)=6.1.1.5; DstPort(1008)=22; RcvVPNInstance(1041)=--; UpperLimit(1048)=10; Action(1049)=logging; BeginTime_c(1011)=20131009093351.

Explanation

This message is sent when the number of ICMP packets sent to a destination per second exceeds the rate limit.

Recommended action

No action is required.

 

ATK_ICMP_INFO_REQ

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_INFO_REQ: IcmpType(1058)=15; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP information request logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_INFO_REQ_RAW

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_INFO_REQ_RAW: IcmpType(1058)=15; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP information requests of the same attributes, this message is sent only when the first request is received.

If log aggregation is disabled, this message is sent every time an ICMP information request is received.

Recommended action

No action is required.

 

ATK_ICMP_INFO_REQ_RAW_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_INFO_REQ_RAW_SZ: IcmpType(1058)=15; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP information requests of the same attributes, this message is sent only when the first request is received.

If log aggregation is disabled, this message is sent every time an ICMP information request is received.

Recommended action

No action is required.

 

ATK_ICMP_INFO_REQ_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_INFO_REQ_SZ: IcmpType(1058)=15; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP information request logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_INFO_RPL

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_INFO_RPL: IcmpType(1058)=16; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP information reply logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_INFO_RPL_RAW

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_INFO_RPL_RAW: IcmpType(1058)=16; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP information replies of the same attributes, this message is sent only when the first reply is received.

If log aggregation is disabled, this message is sent every time an ICMP information reply is received.

Recommended action

No action is required.

 

ATK_ICMP_INFO_RPL_RAW_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_INFO_RPL_RAW_SZ: IcmpType(1058)=16; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP information replies of the same attributes, this message is sent only when the first reply is received.

If log aggregation is disabled, this message is sent every time an ICMP information reply is received.

Recommended action

No action is required.

 

ATK_ICMP_INFO_RPL_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_INFO_RPL_SZ: IcmpType(1058)=16; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP information reply logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_LARGE

Message text

RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: Receiving interface name.

$2: Source IP address.

$3: IP address of the peer DS-Lite tunnel interface.

$4: Destination IP address.

$5: Name of the receiving VPN instance.

$6: Actions against the attack.

$7: Start time of the attack.

$8: End time of the attack.

$9: Attack times.

Severity level

3

Example

ATK/3/ATK_ICMP_LARGE: RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011074913; EndTime_c(1012)=20131011075413; AtkTimes(1050)=2.

Explanation

This message is sent when large ICMP packet logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_LARGE_RAW

Message text

RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: Receiving interface name.

$2: Source IP address.

$3: IP address of the peer DS-Lite tunnel interface.

$4: Destination IP address.

$5: Name of the receiving VPN instance.

$6: Actions against the attack.

Severity level

3

Example

ATK/3/ATK_ICMP_LARGE_RAW: RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for large ICMP packets of the same attributes, this message is sent only when the first packet is received.

If log aggregation is disabled, this message is sent every time a large ICMP packet is received.

Recommended action

No action is required.

 

ATK_ICMP_LARGE_RAW_SZ

Message text

SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: Source security zone name.

$2: Source IP address.

$3: IP address of the peer DS-Lite tunnel interface.

$4: Destination IP address.

$5: Name of the receiving VPN instance.

$6: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_LARGE_RAW_SZ: SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for large ICMP packets of the same attributes, this message is sent only when the first packet is received.

If log aggregation is disabled, this message is sent every time a large ICMP packet is received.

Recommended action

No action is required.

 

ATK_ICMP_LARGE_SZ

Message text

SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: Source security zone name.

$2: Source IP address.

$3: IP address of the peer DS-Lite tunnel interface.

$4: Destination IP address.

$5: Name of the receiving VPN instance.

$6: Actions against the attack.

$7: Start time of the attack.

$8: End time of the attack.

$9: Attack times.

Severity level

3

Example

ATK/3/ATK_ICMP_LARGE_SZ: SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011074913; EndTime_c(1012)=20131011075413; AtkTimes(1050)=2.

Explanation

This message is sent when large ICMP packet logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_PARAPROBLEM

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_PARAPROBLEM: IcmpType(1058)=12; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP parameter problem logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_PARAPROBLEM_RAW

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_PARAPROBLEM_RAW: IcmpType(1058)=12; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP parameter problem packets of the same attributes, this message is sent only when the first packet is received.

If log aggregation is disabled, this message is sent every time an ICMP parameter problem packet is received.

Recommended action

No action is required.

 

ATK_ICMP_PARAPROBLEM_RAW_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_PARAPROBLEM_RAW_SZ: IcmpType(1058)=12; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP parameter problem packets of the same attributes, this message is sent only when the first packet is received.

If log aggregation is disabled, this message is sent every time an ICMP parameter problem packet is received.

Recommended action

No action is required.

 

ATK_ICMP_PARAPROBLEM_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_PARAPROBLEM_SZ: IcmpType(1058)=12; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP parameter problem logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_PINGOFDEATH

Message text

RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: Receiving interface name.

$2: Source IP address.

$3: IP address of the peer DS-Lite tunnel interface.

$4: Destination IP address.

$5: Name of the receiving VPN instance.

$6: Actions against the attack.

$7: Start time of the attack.

$8: End time of the attack.

$9: Attack times.

Severity level

3

Example

ATK/3/ATK_ICMP_PINGOFDEATH: RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011074913; EndTime_c(1012)=20131011075413; AtkTimes(1050)=2.

Explanation

This message is sent when logs are aggregated for ICMP packets larger than 65535 bytes with the MF flag set to 0.

Recommended action

No action is required.

 

ATK_ICMP_PINGOFDEATH_RAW

Message text

RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: Receiving interface name.

$2: Source IP address.

$3: IP address of the peer DS-Lite tunnel interface.

$4: Destination IP address.

$5: Name of the receiving VPN instance.

$6: Actions against the attack.

Severity level

3

Example

ATK/3/ATK_ICMP_PINGOFDEATH_RAW: RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

This message is for the ping of death attack. The attack uses ICMP packets larger than 65535 bytes with the MF flag set to 0.

If log aggregation is enabled, for packets of the same attributes, this message is sent only when the first packet is received.

If log aggregation is disabled, this message is sent every time a packet is received.

Recommended action

No action is required.

 

ATK_ICMP_PINGOFDEATH_RAW_SZ

Message text

SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: Source security zone name.

$2: Source IP address.

$3: IP address of the peer DS-Lite tunnel interface.

$4: Destination IP address.

$5: Name of the receiving VPN instance.

$6: Actions against the attack.

Severity level

3

Example

ATK/3/ATK_ICMP_PINGOFDEATH_RAW_SZ: SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

This message is for the ping of death attack. The attack uses ICMP packets larger than 65535 bytes with the MF flag set to 0.

If log aggregation is enabled, for packets of the same attributes, this message is sent only when the first packet is received.

If log aggregation is disabled, this message is sent every time a packet is received.

Recommended action

No action is required.

 

ATK_ICMP_PINGOFDEATH_SZ

Message text

SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: Source security zone name.

$2: Source IP address.

$3: IP address of the peer DS-Lite tunnel interface.

$4: Destination IP address.

$5: Name of the receiving VPN instance.

$6: Actions against the attack.

$7: Start time of the attack.

$8: End time of the attack.

$9: Attack times.

Severity level

3

Example

ATK/3/ATK_ICMP_PINGOFDEATH_SZ: SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011074913; EndTime_c(1012)=20131011075413; AtkTimes(1050)=2.

Explanation

This message is sent when logs are aggregated for ICMP packets larger than 65535 bytes with the MF flag set to 0.

Recommended action

No action is required.

 

ATK_ICMP_REDIRECT

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_REDIRECT: IcmpType(1058)=5; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP redirect logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_REDIRECT_RAW

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_REDIRECT_RAW: IcmpType(1058)=5; RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP redirect packets of the same attributes, this message is sent only when the first packet is received.

If log aggregation is disabled, this message is sent every time an ICMP redirect packet is received.

Recommended action

No action is required.

 

ATK_ICMP_REDIRECT_RAW_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

Severity level

5

Example

ATK/5/ATK_ICMP_REDIRECT_RAW_SZ: IcmpType(1058)=5; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

If log aggregation is enabled, for ICMP redirect packets of the same attributes, this message is sent only when the first packet is received.

If log aggregation is disabled, this message is sent every time an ICMP redirect packet is received.

Recommended action

No action is required.

 

ATK_ICMP_REDIRECT_SZ

Message text

IcmpType(1058)=[UINT32]; SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Source security zone name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.

Severity level

5

Example

ATK/5/ATK_ICMP_REDIRECT_SZ: IcmpType(1058)=5; SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011091319; EndTime_c(1012)=20131011091819; AtkTimes(1050)=2.

Explanation

This message is sent when ICMP redirect logs are aggregated.

Recommended action

No action is required.

 

ATK_ICMP_SMURF

Message text

RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: Receiving interface name.

$2: Source IP address.

$3: IP address of the peer DS-Lite tunnel interface.

$4: Destination IP address.

$5: Name of the receiving VPN instance.

$6: Actions against the attack.

$7: Start time of the attack.

$8: End time of the attack.

$9: Attack times.

Severity level

3

Example

ATK/3/ATK_ICMP_SMURF: RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011074913; EndTime_c(1012)=20131011075413; AtkTimes(1050)=2.

Explanation

This message is sent when logs are aggregated for ICMP echo requests whose destination IP address is one of the following addresses:

·     A broadcast or network address of A, B, or C class.

·     An IP address of D or E class.

·     The broadcast or network address of the network where the receiving interface resides.

Recommended action

No action is required.

 

ATK_ICMP_SMURF_RAW

Message text

RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: Receiving interface name.

$2: Source IP address.

$3: IP address of the peer DS-Lite tunnel interface.

$4: Destination IP address.

$5: Name of the receiving VPN instance.

$6: Actions against the attack.

Severity level

3

Example

ATK/3/ATK_ICMP_SMURF_RAW: RcvIfName(1023)=Ethernet0/0/2; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

This message is for the smurf attack. The attack uses ICMP echo requests with the destination IP address being one of the following addresses:

·     A broadcast or network address of A, B, or C class.

·     An IP address of D or E class.

·     The broadcast or network address of the network where the receiving interface resides.

If log aggregation is enabled, for requests of the same attributes, this message is sent only when the first request is received.

If log aggregation is disabled, this message is sent every time a request is received.

Recommended action

No action is required.

 

ATK_ICMP_SMURF_RAW_SZ

Message text

SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING].

Variable fields

$1: Source security zone name.

$2: Source IP address.

$3: IP address of the peer DS-Lite tunnel interface.

$4: Destination IP address.

$5: Name of the receiving VPN instance.

$6: Actions against the attack.

Severity level

3

Example

ATK/3/ATK_ICMP_SMURF_RAW_SZ: SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging.

Explanation

This message is for the smurf attack. The attack uses ICMP echo requests with the destination IP address being one of the following addresses:

·     A broadcast or network address of A, B, or C class.

·     An IP address of D or E class.

·     The broadcast or network address of the network where the receiving interface resides.

If log aggregation is enabled, for requests of the same attributes, this message is sent only when the first request is received.

If log aggregation is disabled, this message is sent every time a request is received.

Recommended action

No action is required.

 

ATK_ICMP_SMURF_SZ

Message text

SrcZoneName(1025)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: Source security zone name.

$2: Source IP address.

$3: IP address of the peer DS-Lite tunnel interface.

$4: Destination IP address.

$5: Name of the receiving VPN instance.

$6: Actions against the attack.

$7: Start time of the attack.

$8: End time of the attack.

$9: Attack times.

Severity level

3

Example

ATK/3/ATK_ICMP_SMURF_SZ: SrcZoneName(1025)=Trust; SrcIPAddr(1003)=9.1.1.1; DSLiteTunnelPeer(1040)=--; DstIPAddr(1007)=6.1.1.1; RcvVPNInstance(1041)=--; Action(1049)=logging; BeginTime_c(1011)=20131011074913; EndTime_c(1012)=20131011075413; AtkTimes(1050)=2.

Explanation

This message is sent when logs are aggregated for ICMP echo requests whose destination IP address is one of the following addresses:

·     A broadcast or network address of A, B, or C class.

·     An IP address of D or E class.

·     The broadcast or network address of the network where the receiving interface resides.

Recommended action

No action is required.

 

ATK_ICMP_SOURCEQUENCH

Message text

IcmpType(1058)=[UINT32]; RcvIfName(1023)=[STRING]; SrcIPAddr(1003)=[IPADDR]; DSLiteTunnelPeer(1040)=[STRING]; DstIPAddr(1007)=[IPADDR]; RcvVPNInstance(1041)=[STRING]; Action(1049)=[STRING]; BeginTime_c(1011)=[STRING]; EndTime_c(1012)=[STRING]; AtkTimes(1050)=[UINT32].

Variable fields

$1: ICMP message type.

$2: Receiving interface name.

$3: Source IP address.

$4: IP address of the peer DS-Lite tunnel interface.

$5: Destination IP address.

$6: Name of the receiving VPN instance.

$7: Actions against the attack.

$8: Start time of the attack.

$9: End time of the attack.

$10: Attack times.